Basic Inspection
- Diagnosis and Repair Work Flow
- Additional Service When Replacing Power Window Motor
- System Initialization
- Anti-Pinch Inspection
Diagnosis and Repair Work Flow Nissan Ariya 1st generation
Work Flow
OVERALL SEQUENCE

DETAILED FLOW
GET INFORMATION FOR SYMPTOM
Get detailed information from the customer about the symptom (the condition and the environment when the incident/malfunction occurs).
Check operation condition of the function that is malfunctioning.
GO TO 2.
CHECK DTC
Check DTC.
Perform the following procedure if DTC is detected.
Record DTC and freeze frame data (Print them out using CONSULT.)
Erase DTC.
Study the relationship between the cause detected by DTC and the symptom described by the customer.
Are any symptoms described and any DTC detected?
Symptom is described, DTC is detected>>GO TO 3.
Symptom is described, DTC is not detected>>GO TO 4.
Symptom is not described, DTC is detected>>GO TO 5.
CONFIRM THE SYMPTOM
Try to confirm the symptom described by the customer.
Also study the normal operation and fail-safe related to the symptom.
Verify relation between the symptom and the condition when the symptom is detected.
>>GO TO 5.
CONFIRM THE SYMPTOM
Try to confirm the symptom described by the customer.
Verify relation between the symptom and the condition when the symptom is detected.
>>GO TO 6.
PERFORM DTC CONFIRMATION PROCEDURE
Perform DTC CONFIRMATION PROCEDURE for the detected DTC, and then check that DTC is detected again. At this time, always connect CONSULT to the Nissan Ariya vehicle, and check self diagnostic results in real time.
If two or more DTCs are detected, refer to DTC INSPECTION PRIORITY CHART, and determine trouble diagnosis order.
Is DTC detected?
YES>>GO TO 7.
NO>>Check according to Intermittent Incident.
DETECT MALFUNCTIONING SYSTEM BY SYMPTOM DIAGNOSIS
Detect malfunctioning system according to SYMPTOM DIAGNOSIS based on the confirmed symptom in step 4, and determine the trouble diagnosis order based on possible causes and symptom.
Is the symptom described?
YES>>GO TO 7.
NO>>Monitor input data from related sensors or check voltage of related module terminals using CONSULT.
DETECT MALFUNCTIONING PART BY DIAGNOSIS PROCEDURE
Inspect according to Diagnosis Procedure of the system.
Is malfunctioning part detected?
YES>>GO TO 8.
NO>>Check according to Intermittent Incident.
REPAIR OR REPLACE THE MALFUNCTIONING PART
Repair or replace the malfunctioning part.
Reconnect parts or connectors disconnected during Diagnosis Procedure again after repair and replacement.
Check DTC. If DTC is detected, erase it.
GO TO 9.
FINAL CHECK
When DTC is detected in step 2, perform DTC CONFIRMATION PROCEDURE again, and then check that the malfunction is repaired securely.
When symptom is described by the customer, refer to confirmed symptom in step 3 or 4, and check that the symptom is not detected.
Is DTC detected and does symptom remain?
YES-1>>DTC is detected: GO TO 7.
YES-2>>Symptom remains: GO TO 4.
NO>>Before returning the Nissan Ariya vehicle to the customer, always erase DTC.
Additional Service When Replacing Power Window Motor Nissan Ariya 1st generation
Description
When each power window motor replaced, the initialization is necessary for normal operation of power window system.
Auto-up operation
Anti-pinch function
Remote control function
Work Procedure
SYSTEM INITIALIZATION
Perform system initialization. Refer to Description.
>>GO TO 2 .
CHECK ANTI-PINCH FUNCTION
Check anti-pinch function. Refer to Description.
>>END
System Initialization Nissan Ariya 2026
Description
If any of the following operations are performed, the initialization is necessary for normal operation of power window system. Refer to Work Procedure.
When power window motor replaced.
Power supply to the power window motor is not cut off properly.
Removal and installation of regulator assembly.
Removal and installation of power window motor from regulator assembly.
Operation of regulator assembly as an independent unit.
Removal and installation of door glass.
Removal and installation of door glass run.
Auto-up operation
Anti-pinch function
Remote control function
Work Procedure
SYSTEM INITIALIZATION
Close the door.
Power switch ON.
Continue pulling the power window switch UP until glass stops at fully closed position then release the switch. *1
Keep pulling the switch for 5 seconds or more. *2
Continue pressing the power window switch DOWN until glass stops then release the switch.
Keep pressing the switch for 5 seconds or more. *2
After glass moves again, keep pressing the switch until glass reaches the fully open position.
Continue pulling the power window switch UP (MANUAL UP operation) until glass stops at fully closed position.
Check that AUTO UP function operates normally.
*2: After keep pulling or pressing 5 seconds or more, glass moves again.
>>GO TO 2.
ANTI-PINCH INSPECTION
Check anti-pinch function. Refer to Description.
>>END
Anti-Pinch Inspection Nissan Ariya
Description
If any of the following operations are performed, the initialization is necessary for normal operation of anti-pinch function. Refer to Work Procedure.
When power window motor replaced.
Power supply to the power window motor is not cut off properly.
Removal and installation of regulator assembly.
Removal and installation of power window motor from regulator assembly.
Operation of regulator assembly as an independent unit.
Removal and installation of door glass.
Removal and installation of door glass run.
Work Procedure
CHECK ANTI-PINCH FUNCTION
Fully open the door glass.
Place a piece of wood near fully closed position.
Close door glass completely with AUTO UP.
Check the following conditions.
Check that door glass lowers for approximately 145 mm (5.71 in) or more without pinching piece of wood and stops.
Check that door glass does not rise when operating the power window main switch while lowering.
END