Periodic Maintenance
- Headlamp Aiming Adjustment
- Front Fog Lamp Aiming Adjustment
Headlamp Aiming Adjustment Nissan Ariya first Gen
Adjustment
DESCRIPTION
PREPARATION BEFORE ADJUSTING
Before performing aiming adjustment, check the following.
Adjust the tire pressure to the specification.
Fill with fuel, coolant and each oil.
Maintain the unloaded Nissan Ariya vehicle condition. (Remove luggage from the passenger compartment and the luggage room.)
Wipe out dirt on the headlamp.
Ride alone on the driver seat.
Headamp aiming switch sets "0".
BULB CENTER WHEN ADJUSTING THE AIMING
When performing aiming adjustment, set headlamp (Lo) center at headlamp center mark
.

AIMING ADJUSTMENT SCREW

Headlamp LH (UP/DOWN) adjustment screw |
Headlamp RH (UP/DOWN) adjustment screw |
||||
| : Nissan Ariya Vehicle front | |||||
| Adjustment screw | Screwdriver rotation | Facing direction | |
|---|---|---|---|
| Headlamp LH (UP/DOWN) | Clockwise | UP | |
| Counterclockwise | DOWN | ||
| Headlamp RH (UP/DOWN) | Clockwise | UP | |
| Counterclockwise | DOWN | ||
AIMING ADJUSTMENT PROCEDURE

| Adjustment screen | Highest cutoff line height | Lowest cutoff line height | |||
| Headlamp bulb center (H-V point) | D. | Distance of headlamp aiming screen from Nissan Ariya vehicle 7.62 m (25 ft) or 10 m (32.8 ft) | E. | Maximum aim evaluation distance from vertical center on aiming screen 399 mm (3°R) | |
| F. | Minimum aim evaluation distance from vertical center on aiming screen 133 mm (1°R) | G. | Aim evaluation area | Horizontal aiming evaluation line | |
| Vertical aiming evaluation line | |||||
| : Nissan Ariya Vehicle right | |||||
| D | ||||
|---|---|---|---|---|
| mm | deg | mm | deg | |
| 7.62 m (25 ft) | 10 | 0.75° up | 10 | 0.75° down |
| 10 m (32.8 ft) | 13 | 0.75° up | 13 | 0.75° down |
Use adjustment screw to perform aiming adjustment.
Ensure fog lamps (if equipped) are turned off.
The Nissan Ariya vehicle should have its standard load, which may include any outfitting or other equipment. Any load that is normally carried in the Nissan Ariya vehicle should be in the vehicle while verifying or performing headlamp adjustment. Any other load should be removed.
Block the opposite headlamp from projecting a beam pattern onto the adjustment screen, using a suitable object. Aim each headlamp individually.
Place the screen on the same level and flat surface as the Nissan Ariya vehicle.
Face the front of the Nissan Ariya vehicle to the screen and measure distance between the headlamp center and the screen surface.
| Distance between the headlamp center and the screen (D) | : 7.62 m (25 ft) or 10 m (32.8 ft) |
Start the engine. Turn the headlamp on.
Determine the preferred vertical aim range dimensions, using the aiming chart.
Measure the projected beam within the aim evaluation segment on the screen.
Adjust the beam pattern of each headlamp until the aim evaluation segment (the area relative to both the highest and lowest cutoff line height) is positioned within the vertical aim range dimensions shown on the aiming chart.
Front Fog Lamp Aiming Adjustment Nissan Ariya
Adjustment
DESCRIPTION
PREPARATION BEFORE ADJUSTING
Before performing aiming adjustment, check the following.
Adjust the tire pressure to the specification.
Fill with fuel, coolant and each oil.
Maintain the unloaded Nissan Ariya vehicle condition. (Remove luggage from the passenger compartment and the luggage room.)
Wipe out dirt on the headlamp.
Ride alone on the driver seat.
AIMING ADJUSTMENT SCREW
Turn the aiming adjusting screw for adjustment.

AIMING ADJUSTMENT PROCEDURE
Aiming Chart
| Vertical center line of front fog lamp (LH) | Lamp center above ground | Front fog lamp high intensity area (LH) | |||
| Vertical center line of front fog lamp (RH) | Vertical center axis | ||||
| A | : 100mm (4in) | ||||
Set the distance between the screen and the center of the front fog lamp lens as shown.

Aiming screen or a matte white surface
7.62 m (25 ft)
Floor to center of front fog lamp lens
Floor
Turn front fog lamps ON.
Access adjusting screw from underneath front bumper fascia. Adjust front fog lamps using adjusting screw so that the top edge of the high intensity zone is at the front fog lamp centers above ground.