Brake Control System :: E-Step
- System Description
- Ecu Diagnosis Information. Chassis Control Module
- Basic Inspection. Diagnosis and Repair Work Flow
- Component Parts /circuit Diagnosis. E-Step Switch
- Removal and Installation
Ecu Diagnosis Information. Chassis Control Module Nissan Ariya 1st generation
List of ECU Reference
| ECU | Reference |
|---|---|
| Chassis control module | DTC Index |
| Physical Values | |
| Values On The Diagnosis Tool | |
| Fail-safe | |
| DTC Inspection Priority Chart |
Basic Inspection. Diagnosis and Repair Work Flow Nissan Ariya 2026
Work Flow
DETAILED FLOW
INTERVIEW FROM THE CUSTOMER
Clarify customer complaints before inspection. First of all, perform an interview utilizing diagnostic work sheet and reproduce the symptom as well as fully understand it. Ask customer about his/her complaints carefully. Check symptoms by driving Nissan Ariya vehicle with customer, if necessary. Refer to Diagnostic Work Sheet.
>>GO TO 2.
CHECK SYMPTOM
Reproduce the symptom that is indicated by the customer, based on the information from the customer obtained by interview. Also check that the symptom is not caused by fail-safe mode. Refer to Fail-safe.
>>GO TO 3.
PERFORM THE SELF-DIAGNOSIS
With CONSULT
Perform “All DTC Reading”.
Is DTC detected?
YES>>Record or print self-diagnosis results and freeze frame data (FFD). GO TO 4.
NO>>INSPECTION END
PERFORM DTC DIAGNOSIS PROCEDURE
With CONSULT
Perform confirmation procedures for the error-detected system.
Is DTC detected?
YES>>GO TO 5.
NO>>Check harness and connectors based on the information obtained by interview. Refer to Intermittent Incident.
REPAIR OR REPLACE ERROR-DETECTED PART
With CONSULT
Repair or replace error-detected parts.
Reconnect part or connector after repairing or replacing.
When DTC is detected, erase self-diagnostic result for “All DTC Reading”.
GO TO 6.
FINAL CHECK
With CONSULT
Check the "Values On The Diagnosis Tool" for "CHASSIS CONTROL".
Recheck the symptom and check that the symptom is not reproduced on the same conditions.
Is the symptom reproduced?
YES>>GO TO 3.
NO>>INSPECTION END
Diagnostic Work Sheet
DESCRIPTION
In general, customers have their own criteria for a problem. Therefore, it is important to understand the symptom and status well enough by asking the customer about his/her concerns carefully. To systemize all the information for the diagnosis, prepare the interview sheet referring to the interview points.
In some cases, multiple conditions that appear simultaneously may cause a DTC to be detected.
INTERVIEW SHEET SAMPLE
| Interview sheet | |||||
|---|---|---|---|---|---|
| Customer name | MR/MS | Registration number | Initial year registration | ||
| Nissan Ariya Vehicle type | VIN | ||||
| Storage date | Engine/traction Motor | Mileage | km (Mile) | ||
| Symptom | □ Does not operate ( | ) function | |||
| □ Warning lamp for ( | ) turns ON. | ||||
| □ Noise □ Vibration | |||||
| □ Other ( | ) | ||||
| First occurrence | □ Recently □ Other ( | ) | |||
| Frequency of occurrence | □ Always □ Under a certain conditions of □ Sometimes ( time(s)/day) | ||||
| Climate conditions | □ Irrelevant | ||||
| Weather | □ Fine □ Cloud □ Rain □Snow □ Others ( | ) | |||
| Temperature | □ Hot □Warm □ Cool □ Cold □ Temperature [Approx. | °C (°F)] | |||
| Relative humidity | □ High □ Moderate □ Low | ||||
| Road conditions | □ Urban area □ Suburb area □ Highway □ Mountainous road (uphill or downhill) □ Rough road | ||||
| Operating condition, etc. | □ Irrelevant □ When engine/traction motor starts □ During idling □ During driving □ During acceleration □ At constant speed driving □ During deceleration □ During cornering (right curve or left curve) □ When steering wheel is steered (to right or to left) |
||||
| Other conditions | |||||
| Nissan Ariya Vehicle equipment | |||||
| Memo | |||||
Component Parts /circuit Diagnosis. E-Step Switch Nissan Ariya: FE0
Component Function Check
CHECK e-Step SWITCH OPERATION
Check that information display in combination meter switched when e-Step switch is operated. Refer to System Description.
Is the inspection result normal?
YES>>INSPECTION END
NO>>Refer to Diagnosis Procedure.
Diagnosis Procedure
PERFORM SELF-DIAGNOSIS
With CONSULT
Perform “All DTC Reading”.
Is DTC detected?
YES>>Record or print self-diagnosis results and freeze frame data (FFD). GO TO 2.
NO-1>>When there is a symptom: GO TO 3.
NO-2>>When there is a not symptom: INSPECTION END
CHECK EACH SYSTEM
Perform the trouble diagnosis of system that DTC indicated.
>>GO TO 10.
CHECK e-Step DISPLAY
Power switch OFF and wait at least 1 minute.
Power switch ON.
By operating e-Step switch, turn ON/OFF e-Step function. Refer to Operation.
Confirm that the e-Step display is displayed and that ON / OFF is switched. Refer to System Description.
Is the e-Step display displayed and ON / OFF switched?
YES>>GO TO 10.
NO>>GO TO 4.
CHECK DATA MONITOR
With CONSULT
Select “CHASSIS CONTROL”, “Data monitor” according this order, check the “e-Pedal VCM status”. Refer to Values On The Diagnosis Tool.
Is the “Malfunction” displayed?
YES>>GO TO 9.
NO>>GO TO 5.
CHECK COMBINATION METER
With CONSULT
Perform self-diagnosis for "COMBINATION METER”.
Is DTC detected?
YES>>GO TO 2.
NO>>GO TO 6.
CHECK e-Step SWITCH SIGNAL CIRCUIT
Powe switch OFF (Auto ACC function OFF).
Disconnect VCM harness connector.
Disconnect center console finisher harness connector.
Check the continuity between VCM harness connector and center console finisher harness connector.
VCM Center console finisher Continuity Connector Terminal Connector Terminal E47 54 M204 6 Existed Perform the trouble diagnosis for center console finisher power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 7.
NO>>Repair / replace harness or connector. GO TO 10.
CHECK e-Step SWITCH GROUND CIRCUIT
Check the continuity between center console finisher harness connector and ground.
| Center console finisher | — | Continuity | |
|---|---|---|---|
| Connector | Terminal | ||
| M204 | 16 | Ground | Existed |
Is the inspection result normal?
YES>>GO TO 8.
NO>>Repair / replace harness or connector. GO TO 10.
REPLACE e-Step SWITCH
Replace the center console finisher. Refer to Removal & Installation.
>>GO TO 10.
CHECK VCM
With CONSULT
Perform self-diagnosis for "EV/HEV”.
Is DTC detected?
YES>>GO TO 2.
NO>>GO TO 10.
FINAL CHECK
Recheck the symptom and check that the symptom is not reproduced under the same conditions.
Is the inspection result normal?
YES>>INSPECTION END
NO>>GO TO 1.