Removal and Installation

In this manual: Removal and Installation
How to Use This Manual — 1Precautions — 1Preparation — 1Vehicle Information — 1Basic Inspection — 1Preparation. Commercial Service Tools Or/and Repair Part — 1Description — 1Component Parts — 1System — 1Diagnosis System (vcm) — 1Ecu Diagnosis Information. Vcm — 1Ev Control System — 1Ev/hev (vcm) — 1Component Parts /circuit Diagnosis — 1Ev Control System — 1Periodic Maintenance. Ev System Warning Lamp — 1Removal and Installation. Vcm — 1Traction Motor System :: Front Traction Motor — 1Preparation — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Traction Motor System :: Rear Traction Motor — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Ev Battery System :: 66kwh Li-Ion Battery — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Disassembly and Assembly — 2Service Data — 1Ev Battery System :: 91kwh Li-Ion Battery — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Disassembly and Assembly — 1Service Data — 2Preparation. Vehicle Charging System — 1Vehicle Charging System :: Description — 1Component Parts — 2System — 1Diagnosis System (on-Board Charger) — 1Diagnosis System (dc/dc Converter) — 1Ecu Diagnosis Information — 1Vehicle Charging System — 1Charger/pd Module (on-Board Charger) — 1Cplc (cplc) — 1Dcdc (dc/dc Converter) — 1Component Parts/circuit Diagnosis — 1Symptom Diagnosis — 1Evse Inspection — 1Periodic Maintenance — 1Removal and Installation — 1Disassembly and Assembly — 1Preparation. High Voltage Cooling System — 1Description — 1Symptom Diagnosis. Overheating Cause Analysis — 1Periodic Maintenance — 1Coolant — 1Removal and Installation — 1Radiator — 1Service Data — 1Removal and Installation. Accelerator Control System — 1Reduction Gear: Re1f62a — 1Removal and Installation — 1Transaxle & Transmission :: Electric Shift — 1Description — 3Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Rear Final Drive: Rn1r62a — 1Removal and Installation — 1Preparation. Front Axle System — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data. Front Drive Shaft — 12wd — 14wd — 1Periodic Maintenance — 1Removal and Installation — 1Preparation. Front Suspension System — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Preparation. Road Wheels & Tires System — 1Description — 1System — 1Ecu Diagnosis Information. Bcm (body Control Module) — 1Tpms — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance. Road Wheels & Tires — 1Removal and Installation — 1Service Data — 1Preparation. Brake System — 1System Description — 1Component Parts — 1Ecu Diagnosis Information. Electrically-Driven Intelligent Brake Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Preparation. Parking Brake System — 1System Description — 1Component Parts — 1System — 1Ecu Diagnosis Information. Abs Actuator and Electric Unit (control Unit) — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Component Parts /circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Brake Control System :: With Vdc — 1System Description — 3Basic Inspection — 2Dtc/circuit Diagnosis — 1Symptom Diagnosis — 2Removal and Installation — 1Brake Control System :: Automatic Brake Hold — 1System Description — 3Component Parts /circuit Diagnosis — 1Removal and Installation — 1Brake Control System :: E-Step — 1System Description — 3Removal and Installation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Symptom Diagnosis — 1Rear Automatic Braking — 1System Description — 1Basic Inspection — 1Preparation. Steering System — 1System Description — 1Component Parts — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance. Steering Wheel — 1Removal and Installation — 1Service Data — 1System Description — 1Component Parts — 1Steering Control System — 1Ecu Diagnosis Information. Power Steering Control Module — 1Dtc/circuit Diagnosis — 1Component Parts /circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation. Power Steering Control Module — 1System Description — 1Removal and Installation — 1System Description — 1System — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Component Parts — 1Basic Inspection — 1Removal and Installation — 1System Description — 1System — 1Ecu Diagnosis Information. Air Bag Diagnosis Sensor Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1System Description. Description. Ventilation System — 1Removal and Installation — 1Preparation. Preparation — 1System Description — 1Basic Inspection — 1Symptom Diagnosis — 1Removal and Installation — 1Electric Compressor — 1Cooler Pipe and Hose — 1A/c Unit Assembly Cover — 1A/c Unit Assembly — 1Heater & Air Conditioning Control System :: Automatic Air Conditioning — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 2Dtc Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 2Preparation. Preparation — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1Preparation. Instrument Panel — 1Component Parts — 1System — 1Ecu Diagnosis Information. Flexible Center Storage Control Module — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Preparation. Preparation — 1Component Parts — 1System — 1Ecu Diagnosis Information. Driver Lumbar Support Control Module — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1System Description — 1System — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Manual Function Does Not Operate — 1Memory Function Does Not Operate — 1Removal and Installation — 1Preparation. Preparation — 1System Description — 1System (intelligent Key System) — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1U2141-87 Can Comm Circuit — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Automatic Back Door Operation Does Not Operate — 1Back Door Does Not Open — 1Door Does Not Lock/unlock with Door Lock and Unlock Switch — 1Removal and Installation — 1Hood — 1Radiator Core Support — 1Charge Port Lid — 1Front Fender — 1Front Door — 1Rear Door — 1Back Door — 1Hood Lock — 1Front Door Lock — 1Rear Door Lock — 1Back Door Lock — 1Outside Key Antenna — 1System Description — 1System — 1Ecu Diagnosis Information. Inverter (front), Inverter (rear), Bcm, Intelligent Key Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Preparation — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Front Passenger Side Power Window Does Not Operate — 1Rear Lh Side Power Window Does Not Operate — 1Rear Rh Side Power Window Does Not Operate — 1Removal and Installation. Power Window Main Switch — 1Preparation. Preparation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Sunroof Switch Assembly — 1Symptom Diagnosis — 1Auto Operation Does Not Operate — 1Removal and Installation — 1Preparation — 1Description — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1Service Information — 6Repair Information — 1Precaution — 1Preparation — 1Removal and Installation — 1Service Data — 1Preparation. Preparation — 1Component Parts — 1System — 1Ecu Diagnosis Information — 1Wiring Diagram. Door Mirror — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Removal and Installation — 1Exterior Lighting System :: Led Headlamp — 1System Description — 3Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance — 1Removal and Installation — 1System Description — 1System — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information. Bcm, Intelligent Key Unit — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis. Interior Lighting System Symptom — 1Removal and Installation — 1Service Data. Bulb Specifications — 1System Description — 1System — 1Ecu Diagnosis Information. Bcm, Ipdm E/r — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1System Description — 1Ecu Diagnosis Information. Bcm — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Preparation. Preparation — 1Removal and Installation. Horn — 1Preparation. Commercial Service Tools Or/and Repair Part — 1System Description — 1Component Parts — 1Ecu Diagnosis Information. Approaching Vehicle Sound for Pedestrians (vsp) Control Unit — 1Approaching Vehicle Sound for Pedestrians (vsp) — 1Vsp [approaching Vehicle Sound for Pedestrians (vsp) Control Unit] — 1Approaching Vehicle Sound for Pedestrians (vsp) System — 1Removal and Installation — 1Removal and Installation — 1Wireless Charger — 1System Description — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Removal and Installation — 1Component Parts — 1System — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information. Bcm — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Can Fundamental — 1Description — 1Trouble Diagnosis — 1Can (controller Area Network) — 1Description — 1
10steps
~60min
4/5difficulty
Done 0 of 10
  • Corrosion Protection
  • Body Construction
  • Replacement Operations

Corrosion Protection Nissan Ariya 2026

Description

To provide improved corrosion prevention, the following anti-corrosive measures have been implemented in NISSAN production plants. When repairing or replacing body panels, it is necessary to use the same anti-corrosive measures.

ANTI-CORROSIVE PRECOATED STEEL (GALVANNEALED STEEL)

To improve repairability and corrosion resistance, a new type of anti-corrosive precoated steel sheet is adopted replacing conventional zinc-coated steel sheet.

Galvannealed steel is electroplated and heated to form Zinc-iron alloy, which provides excellent and long term corrosion resistance with cationic electrodeposition primer.

NISSAN genuine parts are fabricated from galvannealed steel. Therefore, it is recommended that NISSAN genuine parts or an equivalent be used for panel replacement to maintain the anti-corrosive performance built into the Nissan Ariya vehicle at the factory.

PHOSPHATE COATING TREATMENT AND CATIONIC ELECTRODEPOSITION PRIMER

A phosphate coating treatment and a cationic electrodeposition primer, which provide excellent corrosion protection, are applied to all body components.

NISSAN genuine parts are also treated in the same manner. Therefore, it is recommended that NISSAN genuine parts or an equivalent be used for panel replacement to maintain anti-corrosive performance built into the Nissan Ariya vehicle at the factory.

Undercoating

The underside of the floor and wheelhouse are undercoated to prevent rust, vibration, noise and stone chipping. Therefore, when such a panel is replaced or repaired, apply undercoating to that part. Use an undercoating which is rust resistant, soundproof, vibration-proof, shock-resistant, adhesive, and durable.

PRECAUTIONS IN UNDERCOATING

  1. Never apply undercoating to any place unless specified (such as the areas above the muffler and three way catalyst that are subjected to heat).

  2. Never undercoat the exhaust pipe or other parts that become hot.

  3. Never undercoat rotating parts.

  4. Apply bitumen wax after applying undercoating.

  5. After putting seal on the Nissan Ariya vehicle, put undercoating on it.

UNDERCOATED AREAS

2WD

: Undercoated areas

: Sealed portions

AWD

: Undercoated areas

: Sealed portions

Body Sealing

The following figure shows the areas that are sealed at the factory. Sealant that is applied to these areas should be smooth and free from cuts or gaps. Care should be taken not to apply an excess amount of sealant and not to allow other unaffected parts to come into contact with the sealant.

2WD

: Nissan Ariya Vehicle front

: Sealed portions

: Nissan Ariya Vehicle front

: Sealed portions

: Nissan Ariya Vehicle front

: Sealed portions
: Sealed portions

AWD

: Nissan Ariya Vehicle front

: Sealed portions

: Nissan Ariya Vehicle front

: Sealed portions

: Nissan Ariya Vehicle front

: Sealed portions
: Sealed portions

Body Construction Nissan Ariya: FE0

Body Construction

2WD models without Sunroof

Outer side body Outer front pillar reinforcement Lower outer front pillar
Lower inner front pillar reinforcement Upper inner front pillar Inner front pillar bracket
Side dash Outer front pillar Lower front pillar hinge brace
Upper dash Hoodledge reinforcement Weld nut
Inner front pillar reinforcement Lower dash Inner front sill reinforcement
Lower dash reinforcement Rear lower dash Inner sill
1st side member rear outrigger Front outer sill reinforcement Outer sill reinforcement
Front outer sill brace Center sill reinforcement 1st side member outrigger
Front outrigger reinforcement Closing plate reinforcement 2nd cross member
Front floor Front sill bulkhead front Inner sill plate
Outer side roof rail Roof 2nd roof bow
Center roof rail brace Inner side roof rail Center pillar seat belt anchor
Inner center pillar Center pillar hinge brace Center pillar reinforcement
Lower inner center pillar reinforcement Lower hinge plate inner Front sill bulkhead rear
Rear floor front extension Rear seat cross member Rear side member
Front reinforcement connector Outer sill brace Inner sill extension
Nut plate Inner rear wheelhouse Outer rear wheelhouse
Center main back pillar Upper back pillar reinforcement Rear roof rail brace
Inner rear pillar Rear pillar lower reinforcement

2WD models with Sunroof

Outer side body Outer front pillar reinforcement Lower outer front pillar
Lower inner front pillar reinforcement Upper inner front pillar Inner front pillar bracket
Side dash Outer front pillar Lower front pillar hinge brace
Upper dash Hoodledge reinforcement Weld nut
Inner front pillar reinforcement Lower dash Inner front sill reinforcement
Lower dash reinforcement Rear lower dash Inner sill
1st side member rear outrigger Front outer sill reinforcement Outer sill reinforcement
Front outer sill brace Center sill reinforcement 1st side member outrigger
Front outrigger reinforcement Closing plate reinforcement 2nd cross member
Front floor Front sill bulkhead front Inner sill plate
Outer side roof rail Sun roof Side roof rail reinforcement
Inner side roof rail Center pillar seat belt anchor Inner center pillar
Center pillar hinge brace Center pillar reinforcement Lower inner center pillar reinforcement
Lower hinge plate inner Front sill bulkhead rear Rear floor front extension
Rear seat cross member Rear side member Front reinforcement connector
Outer sill brace Inner sill extension Nut plate
Inner rear wheelhouse Outer rear wheelhouse Center main back pillar
Upper back pillar reinforcement Rear roof rail brace Inner rear pillar
Rear pillar lower reinforcement

AWD models without Sunroof

Outer side body Outer front pillar reinforcement Lower outer front pillar
Lower inner front pillar reinforcement Upper inner front pillar Inner front pillar bracket
Side dash Outer front pillar Lower front pillar hinge brace
Upper dash Hoodledge reinforcement Weld nut
Inner front pillar reinforcement Lower dash Inner front sill reinforcement
Lower dash reinforcement Rear lower dash Inner sill
1st side member rear outrigger Front outer sill reinforcement Outer sill reinforcement
Front outer sill brace Center sill reinforcement 1st side member outrigger
Front outrigger reinforcement Closing plate reinforcement 2nd cross member
Front floor Front sill bulkhead front Inner sill plate
Outer side roof rail Roof 2nd roof bow
Center roof rail brace Inner side roof rail Center pillar seat belt anchor
Inner center pillar Center pillar hinge brace Center pillar reinforcement
Lower inner center pillar reinforcement Lower hinge plate inner Front sill bulkhead rear
Rear floor front extension Rear seat cross member Rear side member
Front reinforcement connector Outer sill brace Inner sill extension
Nut plate Inner rear wheelhouse Outer rear wheelhouse
Center main back pillar Upper back pillar reinforcement Rear roof rail brace
Inner rear pillar Rear pillar lower reinforcement

AWD models with Sunroof

Outer side body Outer front pillar reinforcement Lower outer front pillar
Lower inner front pillar reinforcement Upper inner front pillar Inner front pillar bracket
Side dash Outer front pillar Lower front pillar hinge brace
Upper dash Hoodledge reinforcement Weld nut
Inner front pillar reinforcement Lower dash Inner front sill reinforcement
Lower dash reinforcement Rear lower dash Inner sill
1st side member rear outrigger Front outer sill reinforcement Outer sill reinforcement
Front outer sill brace Center sill reinforcement 1st side member outrigger
Front outrigger reinforcement Closing plate reinforcement 2nd cross member
Front floor Front sill bulkhead front Inner sill plate
Outer side roof rail Sun roof Side roof rail reinforcement
Inner side roof rail Center pillar seat belt anchor Inner center pillar
Center pillar hinge brace Center pillar reinforcement Lower inner center pillar reinforcement
Lower hinge plate inner Front sill bulkhead rear Rear floor front extension
Rear seat cross member Rear side member Front reinforcement connector
Outer sill brace Inner sill extension Nut plate
Inner rear wheelhouse Outer rear wheelhouse Center main back pillar
Upper back pillar reinforcement Rear roof rail brace Inner rear pillar
Rear pillar lower reinforcement

Fusible Insulator Applying Part

Apply the fusible insulator (melsheet) to the floor upper surface and dashboard panel interior side to block noise, vibration, and exhaust gas heat.

2WD

Unit: mm (in)

T=3.1 (0.122) T=3.1 (0.122)

T=4.0 (0.157)

LH and RH are symmetrical.

T=4.0 (0.157)

LH and RH are symmetrical.

T=4.0 (0.157)

LH and RH are symmetrical.

T=4.0 (0.157)

LH and RH are symmetrical.

T=4.0 (0.157)

LH and RH are symmetrical.

T=3.1 (0.122)

LH and RH are symmetrical.

T=3.1 (0.122)

LH and RH are symmetrical.

T=3.1 (0.122)

LH and RH are symmetrical.

T=3.1 (0.122)

LH and RH are symmetrical.

T=4.0 (0.157)

LH and RH are symmetrical.

T=4.0 (0.157)

LH and RH are symmetrical.

T=4.0 (0.157)

LH and RH are symmetrical.
T=3.1 (0.122)
T=3.1 (0.122) T=3.1 (0.122)

T=4.0 (0.157)

LH and RH are symmetrical.

T=4.0 (0.157)

LH and RH are symmetrical.

T=4.0 (0.157)

LH and RH are symmetrical.

T=3.1 (0.122)

LH and RH are symmetrical.
Rear wheel house protector (Indoor side view)

: Nissan Ariya Vehicle front

: Fusible insulator applying part

AWD

Unit: mm (in)

T=3.1 (0.122) T=3.1 (0.122)

T=4.0 (0.157)

LH and RH are symmetrical.

T=4.0 (0.157)

LH and RH are symmetrical.

T=4.0 (0.157)

LH and RH are symmetrical.

T=4.0 (0.157)

LH and RH are symmetrical.

T=4.0 (0.157)

LH and RH are symmetrical.

T=3.1 (0.122)

LH and RH are symmetrical.

T=3.1 (0.122)

LH and RH are symmetrical.

T=3.1 (0.122)

LH and RH are symmetrical.

T=3.1 (0.122)

LH and RH are symmetrical.
T=3.1 (0.122)
T=3.1 (0.122) T=3.1 (0.122)
Rear wheel house protector (Indoor side view)

: Nissan Ariya Vehicle front

: Fusible insulator applying part

Replacement Operations Nissan Ariya 2023

Precautions for Body Repair

  • Technicians are encouraged to read the Body Repair Manual (Fundamentals) in order to ensure that the original functions and quality of the Nissan Ariya vehicle are maintained. The Body Repair Manual (Fundamentals) contains additional information, including cautions and warnings, that are not including in this manual. Technicians should refer to both manuals to ensure proper repair.

  • Please note that this information is prepared for worldwide usage, and as such, certain procedures might not apply in some regions or countries.

The symbols used in this section for welding operations are shown below.

Symbol marksDescription
″Number″

″Number″ after symbol mark is the total number of welds to apply.

Example 1: ″4″A = 4 MIG plug welds for 3-panel plug weld method.

Example 2: ″1″× 20 (0.79) = 1 MIG seam weld by length 20 mm (0.79 in).
2-panel spot weld
3-panel spot weld
MIG plug weld

For 3-panel plug weld method

MIG seam weld / Point weld
Rivet
  • Front pillar butt joint can be determined anywhere within shaded area as shown in the figure. The best location for the butt joint is at position A due to the construction of the Nissan Ariya vehicle.

  • Determine cutting position and record distance from the locating indent. Use this distance when cutting the service part. Cut outer front pillar over 60 mm (2.36 in) above the inner front pillar cut position.

  • Prepare a cutting jig to make outer pillar easier to cut. Also, this will permit the service part to be accurately cut at the joint position.

  • An example of cutting operation using a cutting jig is as per the following.

  1. Mark cutting lines.

    A: Cut position of outer pillar

    B: Cut position of inner pillar

  2. Align cutting line with notch on jig. Clamp jig to pillar.

  3. Cut outer pillar along groove of jig (at position A).

  4. Remove jig and cut remaining portions.

  5. Cut inner pillar at position B in same manner.

Welding of Ultra High Strength Steel

SPOT WELDING

Spot welding is limited to ultra high strength steel (tensile strength: 980 MPa) according to the welding conditions listed below.

Welding condition
Welder tip diameter 6 mm
Welding pressure (Gun force) 4150 N
Panel configuration Combination of a plate of tensile strength 980 MPa and that of tensile strength less than 980 MPa. (Up to 3 plates)

Welding current and weld time

Welding current Weld time Welding pressure (Gun force) Description
50 Hz 60 Hz
Before welding 0 A - - 0 N -
First energization 7000 A

0.06 sec

(3 cycle)

0.05 sec

(3 cycle)
4150 N Secure an energization path
Cool down 0 A

0.02 sec

(1 cycle)

0.02 sec

(1 cycle)
4150 N -
Second energization 8000 A

0.22 sec

(11 cycle)

0.22 sec

(13 cycle)
4150 N Main energization for nugget formation
Third energization 4500 A

0.08 sec

(4 cycle)

0.08 sec

(5 cycle)
4150 N Prevent cracking of nugget (prevention of rapid cooling)
Keep pressurization 0 A

0.10 sec

(5 cycle)

0.08 sec

(5 cycle)
4150 N -
After welding 0 A - - 0 N -

PLUG WELDING

To weld ultra high strength steel of tensile strength 980 MPa or more, perform plug welding observing the welding hole diameter described in the manual.

EXAMPLE

Body sealing

: Nissan Ariya Vehicle front

: Drill φ6 mm (0.24 in) hole for the plug welding hole (ultra high strength steel).

: N·m (kg-m, ft-lb)

: For spot welding of steel plate of tensile strength 980 MPa, observe the indicated welding conditions. Refer to ″Welding of Ultra High Strength Steel″.

Radiator Core Support

: Nissan Ariya Vehicle front

: Weld the parts onto the back of the component part.

: N•m (kg-m, ft-lb)
Replacement part
• Side radiator core support assembly • Side radiator core support

Hoodledge

Work after side radiator core support assembly is removed.

: Nissan Ariya Vehicle front
Replacement part
• Front strut housing assembly • Hoodledge reinforcement

: Nissan Ariya Vehicle front

: Weld the parts onto the back of the component part.

View C: Before installing hoodledge reinforcement

PARTIAL REPLACEMENT

Work after side radiator core support assembly is removed.

: Nissan Ariya Vehicle front

: Weld the parts onto the back of the component part.
Replacement part
• Lower hoodledge • Upper hoodledge • Hoodledge reinforcement
• Lower front hoodledge reinforcement
: Nissan Ariya Vehicle front

View E: Before installing hoodledge reinforcement

Front Side Member

Work after side radiator core support assembly and hoodledge are removed.

: Nissan Ariya Vehicle front

: Drill φ10 mm (0.39 in) hole for the plug welding hole (ultra high strength steel).

: Weld the parts onto the back of the component part.

: N•m (kg-m, ft-lb)
Replacement part
• Front side member assembly • Front side member closing plate

: Nissan Ariya Vehicle front

: Drill φ8 mm (0.31 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ10 mm (0.39 in) hole for the plug welding hole (ultra high strength steel).

Front Pillar

Work after hoodledge reinforcement and roof are removed.

Body sealing Urethane foam

: Nissan Ariya Vehicle front

: Drill φ8 mm (0.31 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ9 mm (0.35 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ10 mm (0.39 in) hole for the plug welding hole (ultra high strength steel).
Replacement part
• Outer front side body • Side dash • Upper inner front pillar
• Lower front pillar hinge brace • Outer front pillar reinforcement

View A: Before installing outer front side body

Body sealing Urethane foam
Unit: mm (in)

: Nissan Ariya Vehicle front

: Drill φ8 mm (0.31 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ9 mm (0.35 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ10 mm (0.39 in) hole for the plug welding hole (ultra high strength steel).

View D: Before installing outer front side body

Urethane foam
Unit: mm (in)

: Nissan Ariya Vehicle front

: Drill φ6 mm (0.24 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ7 mm (0.28 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ8 mm (0.31 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ9 mm (0.35 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ11 mm (0.43 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ12 mm (0.47 in) hole for the plug welding hole (ultra high strength steel).

: Weld the parts onto the back of the component part.

: N•m (kg-m, ft-lb)

View J: Before installing outer front side body and lower front pillar hinge brace

View Q: Before installing outer front side body

PARTIAL REPLACEMENT

Work after hoodledge reinforcement is removed.

Body sealing Urethane foam
Unit: mm (in)

: Nissan Ariya Vehicle front

: Drill φ6 mm (0.24 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ8 mm (0.31 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ9 mm (0.35 in) hole for the plug welding hole (ultra high strength steel).
Replacement part
• Outer front side body • Side dash • Lower front pillar hinge brace

View A: Before installing outer front side body

Body sealing Urethane foam

: Nissan Ariya Vehicle front

: Drill φ8 mm (0.31 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ9 mm (0.35 in) hole for the plug welding hole (ultra high strength steel).

View D: Before installing outer front side body

Urethane foam
Unit: mm (in)

: Nissan Ariya Vehicle front

: Drill φ8 mm (0.31 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ10 mm (0.39 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ11 mm (0.43 in) hole for the plug welding hole (ultra high strength steel).

: Weld the parts onto the back of the component part.

: N•m (kg-m, ft-lb)

View J: Before installing outer front side body and lower front pillar hinge brace

Center Pillar

Urethane foam Body sealing
Unit: mm (in)

: Nissan Ariya Vehicle front

: Drill φ6 mm (0.24 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ8 mm (0.31 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ10 mm (0.39 in) hole for the plug welding hole (ultra high strength steel).
Replacement part
• Outer front side body • Inner center pillar assembly • Lower center pillar brace
Urethane foam Body sealing
Unit: mm (in)

: Nissan Ariya Vehicle front

: Drill φ10 mm (0.39 in) hole for the plug welding hole (ultra high strength steel).

View B, E, and G: Before installing outer front side body

Outer Sill

Remove the lower front pillar hinge brace (reusable) and lower center pillar brace (reusable) from the Nissan Ariya vehicle for easier installation.

Urethane foam Body sealing Lower front pillar hinge brace (reusable)
Unit: mm (in)

: Nissan Ariya Vehicle front

: Drill φ8 mm (0.31 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ9 mm (0.35 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ12 mm (0.47 in) hole for the plug welding hole (ultra high strength steel).

: Weld the parts onto the back of the component part.

: For spot welding of steel plate of tensile strength 980 MPa, observe the indicated welding conditions. Refer to Welding of Ultra High Strength Steel
Replacement part
• Outer sill assembly • Outer sill reinforcement

View B: Before installing outer sill assembly

Urethane foam Body sealing Lower center pillar brace (reusable)
Unit: mm (in)

: Nissan Ariya Vehicle front

: Drill φ6 mm (0.24 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ7 mm (0.28 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ8 mm (0.31 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ9 mm (0.35 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ10 mm (0.39 in) hole for the plug welding hole (ultra high strength steel).

: Weld the parts onto the back of the component part.

: For spot welding of steel plate of tensile strength 980 MPa, observe the indicated welding conditions. Refer to Welding of Ultra High Strength Steel

View G: Before installing outer sill assembly

View H: Before installing outer sill assembly and center pillar hinge brace assembly (reusable)

Lower center pillar brace (reusable) Urethane foam Body sealing
Lower front pillar hinge brace (reusable)
Unit: mm (in)

: Nissan Ariya Vehicle front

: Drill φ8 mm (0.31 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ9 mm (0.35 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ10 mm (0.39 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ12 mm (0.47 in) hole for the plug welding hole (ultra high strength steel).

View J and O: Before installing outer sill assembly

PARTIAL REPLACEMENT

Unit: mm (in)
: Nissan Ariya Vehicle front
Replacement part
• Outer sill assembly

Inner Sill

Work after outer sill is removed.

Body sealing
Unit: mm (in)

: Nissan Ariya Vehicle front

: Drill φ7 mm (0.28 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ8 mm (0.31 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ11 mm (0.43 in) hole for the plug welding hole (ultra high strength steel).

: Weld the parts onto the back of the component part.
Replacement part
• Inner sill • Inner center sill assembly
Body sealing
Unit: mm (in)

: Nissan Ariya Vehicle front

: Drill φ8 mm (0.31 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ9 mm (0.35 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ10 mm (0.39 in) hole for the plug welding hole (ultra high strength steel).

: Weld the parts onto the back of the component part.

View E and F: Before installing inner center sill assembly

Rear Fender

Urethane foam Body sealing
Unit: mm (in)
: Nissan Ariya Vehicle front
Replacement part
• Rear fender assembly
Urethane foam Body sealing
Unit: mm (in)

: Nissan Ariya Vehicle front

: Drill φ6 mm (0.24 in) hole for the plug welding hole (ultra high strength steel).

: Weld the parts onto the back of the component part.

View G: Before installing outer side body

Rear Fender Extension

Body sealing
Unit: mm (in)
: Nissan Ariya Vehicle front
Replacement part
• Rear fender extension

Outer Rear Wheelhouse

Work after rear fender is removed.

Remove the outer rear sill reinforcement front (reusable) from the vehicle for easier installation.

Outer rear sill reinforcement (reusable)

: Nissan Ariya Vehicle front

: Weld the parts onto the back of the component part.
Replacement part
• Outer rear wheelhouse • Outer rear wheelhouse extension • Rear fender gusset
Outer rear sill reinforcement
Unit: mm (in)

: Nissan Ariya Vehicle front

: Drill φ6 mm (0.24 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ7 mm (0.28 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ8 mm (0.31 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ10 mm (0.39 in) hole for the plug welding hole (ultra high strength steel).

: Weld the parts onto the back of the component part.

View D: Before installing outer rear sill reinforcement (reusable)

Inner Rear Wheelhouse

Work after rear fender and outer rear wheelhouse are removed.

Unit: mm (in)
: Nissan Ariya Vehicle front
Replacement part
• Inner rear wheelhouse
Body sealing

: Nissan Ariya Vehicle front

: Drill φ6 mm (0.24 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ8 mm (0.31 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ10 mm (0.39 in) hole for the plug welding hole (ultra high strength steel).

: Weld the parts onto the back of the component part.

Inner Rear Pillar Reinforcement

Work after rear fender is removed.

Unit: mm (in)

: Nissan Ariya Vehicle front

: Weld the parts onto the back of the component part.
Replacement part
• Inner rear pillar

Inner Rear Pillar

2WD MODELS

Work after rear fender is removed.

: Nissan Ariya Vehicle front

: Drill φ6 mm (0.24 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ8 mm (0.31 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ11 mm (0.43 in) hole for the plug welding hole (ultra high strength steel).

: Weld the parts onto the back of the component part.

: N•m (kg-m, ft-lb)
Replacement part
• Inner rear pillar
Unit: mm (in)

: Nissan Ariya Vehicle front

: Weld the parts onto the back of the component part.

AWD MODELS

Work after rear fender is removed.

: Nissan Ariya Vehicle front

: Drill φ6 mm (0.24 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ8 mm (0.31 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ11 mm (0.43 in) hole for the plug welding hole (ultra high strength steel).

: Weld the parts onto the back of the component part.

: N•m (kg-m, ft-lb)
Replacement part
• Inner rear pillar
Unit: mm (in)

: Nissan Ariya Vehicle front

: Weld the parts onto the back of the component part.

Rear Panel

2WD MODELS

Unit: mm (in)

: Nissan Ariya Vehicle front

: Weld the parts onto the back of the component part.

: Welding method, the number of welding points, and the distance in the figure apply to both sides of the Nissan Ariya vehicle.
Replacement part
• Upper rear panel

AWD MODELS

Unit: mm (in)

: Nissan Ariya Vehicle front

: Weld the parts onto the back of the component part.

: Welding method, the number of welding points, and the distance in the figure apply to both sides of the Nissan Ariya vehicle.
Replacement part
• Upper rear panel

Rear Floor Rear

2WD MODELS

Work after rear panel is removed.

Remove the rear side floor (reusable) from the vehicle for easier installation.

Rear side floor (reusable)

: Nissan Ariya Vehicle front

: Drill φ6 mm (0.24 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ7 mm (0.28 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ10 mm (0.39 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ12 mm (0.47 in) hole for the plug welding hole (ultra high strength steel).

: Weld the parts onto the back of the component part.

: Welding method and the number of welding points apply to both side of the Nissan Ariya vehicle.
Replacement part
• Rear floor rear • Spare wheel crossmember

AWD MODELS

Work after rear panel is removed.

Remove the rear side floor (reusable) from the vehicle for easier installation.

Rear side floor (reusable)

: Nissan Ariya Vehicle front

: Drill φ6 mm (0.24 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ7 mm (0.28 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ10 mm (0.39 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ12 mm (0.47 in) hole for the plug welding hole (ultra high strength steel).

: Weld the parts onto the back of the component part.

: Welding method and the number of welding points apply to both side of the Nissan Ariya vehicle.
Replacement part
• Rear floor rear • Spare wheel crossmember

Rear Side Member

2WD MODELS

Work after rear fender, rear panel, rear side floor assembly, rear floor rear, outer rear wheelhouse, and inner rear wheelhouse are removed.

Remove the center rear crossmember assembly (reusable) from the vehicle for easier installation.

Center rear crossmember assembly (reusable)
Unit: mm (in)

: Nissan Ariya Vehicle front

: Drill φ6 mm (0.24 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ8 mm (0.31 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ11 mm (0.43 in) hole for the plug welding hole (ultra high strength steel).

: Weld the parts onto the back of the component part.
Replacement part
• Rear side member • Side member closing plate assembly

: Nissan Ariya Vehicle front

: Drill φ6 mm (0.24 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ8 mm (0.31 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ9 mm (0.35 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ10 mm (0.39 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ11 mm (0.43 in) hole for the plug welding hole (ultra high strength steel).

: Weld the parts onto the back of the component part.

AWD MODELS

Work after rear fender, rear panel, rear side floor assembly, rear floor rear, outer rear wheelhouse, and inner rear wheelhouse are removed.

Remove the center rear crossmember assembly (reusable) from the vehicle for easier installation.

Center rear crossmember assembly (reusable)
Unit: mm (in)

: Nissan Ariya Vehicle front

: Drill φ6 mm (0.24 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ8 mm (0.31 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ11 mm (0.43 in) hole for the plug welding hole (ultra high strength steel).

: Weld the parts onto the back of the component part.
Replacement part
• Rear side member • Side member closing plate assembly

: Nissan Ariya Vehicle front

: Drill φ6 mm (0.24 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ8 mm (0.31 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ9 mm (0.35 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ10 mm (0.39 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ11 mm (0.43 in) hole for the plug welding hole (ultra high strength steel).

: Weld the parts onto the back of the component part.

Rear Side Member Extension

2WD MODELS

Work after rear panel is removed.

Remove the spare wheel crossmember (reusable), inner rear wheelhouse rear extension (reusable) from the Nissan Ariya vehicle for easier installation.

Cut two places of inner rear wheelhouse, and raise a panel edge for easier installation.

: Nissan Ariya Vehicle front

: Drill φ10 mm (0.39 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ12 mm (0.47 in) hole for the plug welding hole (ultra high strength steel).

: Weld the parts onto the back of the component part.
Replacement part
• Rear side member
Spare wheel crossmember (reusable) Inner rear wheelhouse rear extension (reusable) The state that raised the inner rear wheelhouse edge.
Unit: mm (in)

: Nissan Ariya Vehicle front

: Drill φ10 mm (0.39 in) hole for the plug welding hole (ultra high strength steel).

AWD MODELS

Work after rear panel is removed.

Remove the spare wheel crossmember (reusable), inner rear wheelhouse rear extension (reusable) from the Nissan Ariya vehicle for easier installation.

Cut two places of inner rear wheelhouse, and raise a panel edge for easier installation.

: Nissan Ariya Vehicle front

: Drill φ10 mm (0.39 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ12 mm (0.47 in) hole for the plug welding hole (ultra high strength steel).

: Weld the parts onto the back of the component part.
Replacement part
• Rear side member
Spare wheel crossmember (reusable) Inner rear wheelhouse rear extension (reusable) The state that raised the inner rear wheelhouse edge.
Unit: mm (in)

: Nissan Ariya Vehicle front

: Drill φ10 mm (0.39 in) hole for the plug welding hole (ultra high strength steel).

Roof

WITHOUT SUNROOF MODELS

Body sealing
Unit: mm (in)

: Nissan Ariya Vehicle front

: Drill φ8 mm (0.31 in) hole for the plug welding hole (ultra high strength steel).

: Drill φ10 mm (0.39 in) hole for the plug welding hole (ultra high strength steel).

: Weld the parts onto the back of the component part.

: Welding method, the number of welding points, and the distance in the figure apply to both sides of the Nissan Ariya vehicle.
Replacement part
• Roof • Roof bow • 2nd roof bow
• 4th roof bow

WITH SUNROOF MODELS

Body sealing
Unit: mm (in)

: Nissan Ariya Vehicle front

: Weld the parts onto the back of the component part.

: Welding method, the number of welding points, and the tightening torque apply to both sides of the Nissan Ariya vehicle.

: N•m (kg-m, ft-lb)
Replacement part
• Roof assembly

Roof Rail

Work after roof is removed.

: Nissan Ariya Vehicle front

: Drill φ7 mm (0.28 in) hole for the plug welding hole (ultra high strength steel).

: Welding method, the number of welding points, and the tightening torque apply to both side of the Nissan Ariya vehicle.

: N•m (kg-m, ft-lb)
Replacement part
• Front roof rail • Rear roof rail