(Inner center front bumper reinforcement component part)
Front bumper reinforcement
(Inner center front bumper reinforcement component part)
Front side member rear
(Front side member closing plate component part)
Front suspension mounting rear bracket
(Front side member closing plate component part)
Front side member brace
(Front side member assembly component part)
Front side member reinforcement
(Front side member assembly component part)
Front outrigger reinforcement
(Side member rear outrigger assembly component part)
1st side member rear outrigger
(Side member rear outrigger assembly component part)
Upper rear seat crossmember
Inner sill extension
(Rear side member component part)
Rear side member
(Rear side member component part)
Rear side member reinforcement
(Rear side member component part)
Rear side member extension reinforcement
(Rear side member component part)
Read the following precautions when repairing HSS and UHSS:
BODY COMPONENT PARTS
ROOF AND DOORS COMPONENT PARTS
Tensile strength
Applicable parts
440 - 590 MPa
Rear side roof reinforcement (With sunroof model only)
(Roof assembly component part)
Rear roof reinforcement (With sunroof model only)
(Roof assembly component part)
Front roof rail
(Front roof rail component part)
4th roof bow (Without Sunroof models only)
Front door guard front bracket
(Front door assembly component part)
Rear door guard front bracket
(Rear door assembly component part)
Tensile strength
Applicable parts
1180 - 1300 MPa
Front roof rail reinforcement
(Front roof rail component part)
2nd roof bow (Without Sunroof models only)
Read the following precautions when repairing HSS and UHSS:
BODY SIDE COMPONENT PARTS
Tensile strength
Applicable parts
440 - 780 MPa
Inner center pillar (Lower)
(Inner center pillar assembly component part)
Lower inner center pillar reinforcement
(Inner center pillar assembly component part)
Center sill reinforcement
(Inner center sill assembly component part)
Center pillar hinge brace (Lower)
(Lower center pillar brace component part)
Lower hinge plate
(Lower center pillar brace component part)
Lower front pillar hinge brace
(Lower front pillar hinge brace component part)
Outer front sill brace
(Outer sill reinforcement component part)
Outer sill reinforcement
(Outer sill reinforcement component part)
Outer sill brace
(Outer sill reinforcement component part)
Shock absorber mounting plate
(Inner rear wheelhouse component part)
Striker plate
(Upper rear panel component part)
Inner center rear bumper reinforcement (Except for "ee" part)
Tensile strength
Applicable parts
980 - 1500 MPa
Inner side roof rail
(Upper inner front pillar component part)
Center roof rail brace (Without Sunroof models only)
(Upper inner front pillar component part)
Front roof rail brace
(Upper inner front pillar component part)
Lower inner front pillar reinforcement
(Upper inner front pillar component part)
Upper inner front pillar
(Upper inner front pillar component part)
Center pillar seat belt anchor
(Inner center pillar assembly component part)
Inner center pillar (Upper)
(Inner center pillar assembly component part)
Upper center pillar brace
(Inner center pillar assembly component part)
Center sill reinforcement
(Inner center sill assembly component part)
Closing plate reinforcement
(Inner center sill assembly component part)
Center pillar hinge brace (Upper)
(Lower center pillar brace component part)
Center pillar reinforcement
(Lower center pillar brace component part)
Outer side roof rail
(Outer front pillar reinforcement component part)
Outer side roof stiffener
(Outer front pillar reinforcement component part)
Outer front pillar reinforcement
(Outer front pillar reinforcement component part)
Lower outer front pillar reinforcement
(Outer front pillar reinforcement component part)
Lower front pillar bulkhead
(Lower front pillar hinge brace component part)
Outer front pillar
(Lower front pillar hinge brace component part)
Outer front sill reinforcement
(Lower front pillar hinge brace component part)
Center sill reinforcement
(Outer sill reinforcement component part)
Outer sill brace
(Outer sill reinforcement component part)
Outer rear sill reinforcement
(Outer sill reinforcement component part)
Rear bumper reinforcement
(Inner center rear bumper reinforcement component part)
Read the following precautions when repairing HSS and UHSS:
Following precautions
Additional points to consider
The repair of reinforcements (such as side members) by heating is not recommended, because it may weaken the component. When heating is unavoidable, never heat HSS parts above 550 °C.
Verify heating temperature with a thermometer.
(Crayon-type and other similar type thermometer are appropriate.)
When you heat the HSS or UHSS parts above 550 °C, it must be replaced with new parts.
When straightening body panels, use caution in pulling any HSS panel. Because HSS is very strong, pulling may cause deformation in adjacent sections of the body. In this case, increase the number of measuring points, and carefully pull the HSS panel.
When cutting HSS panels, avoid gas (torch) cutting if possible. Instead, use a saw to avoid weakening surrounding areas due to heat. If gas (torch) cutting is unavoidable, allow a minimum margin of 50 mm (1.97 in).
When welding HSS panels, use spot welding whenever possible in order to minimize weakening surrounding areas due to heat.
If spot welding is impossible, use MIG. welding. Do not use gas (torch) for welding because it is inferior in welding strength.
Spot welding on HSS panels is harder than that of an ordinary steel panel.
Therefore, when cutting spot welds on a HSS panel, use a low speed high torque drill (1,000 to 1,200 rpm) to increase drill bit durability and facilitate the operation.
Precautions in spot welding HSS
This work should be performed under standard working conditions. Always note the following when spot welding HSS:
The electrode tip diameter must be sized properly according to the metal thickness.
The panel surfaces must fit flush to each other, leaving no gaps.
Follow the specifications for the proper welding pitch.
Unit: mm (in)
Thickness (T)
Minimum pitch (L)
0.6 (0.024)
0.8 (0.031)
1.0 (0.039)
1.2 (0.047)
1.6 (0.063)
1.8 (0.071)
10 (0.39) or more
12 (0.47) or more
18 (0.71) or more
20 (0.79) or more
27 (1.06) or more
31 (1.22) or more
Painting Booth Nissan Ariya 2026
Temperature Control
While using painting booth, outer sill temperature must not exceed 60 °C to prevent deterioration of li-ion battery.
Protection of Vehicle Nissan Ariya 2026
Protection of Vehicle
The seats, glass, and carpet must be removed or covered with appropriate material (spatter cover), according to the type of work to be done, to prevent contamination and welding spatter.
In addition, when cutting the vehicle in an area close to high voltage parts or performing a welding operation, the high voltage parts must be covered with a heat-resistant insulating cover (spatter cover).