Removal and Installation

In this manual: Removal and Installation
How to Use This Manual — 1Precautions — 1Preparation — 1Vehicle Information — 1Basic Inspection — 1Preparation. Commercial Service Tools Or/and Repair Part — 1Description — 1Component Parts — 1System — 1Diagnosis System (vcm) — 1Ecu Diagnosis Information. Vcm — 1Ev Control System — 1Ev/hev (vcm) — 1Component Parts /circuit Diagnosis — 1Ev Control System — 1Periodic Maintenance. Ev System Warning Lamp — 1Removal and Installation. Vcm — 1Traction Motor System :: Front Traction Motor — 1Preparation — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Traction Motor System :: Rear Traction Motor — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Ev Battery System :: 66kwh Li-Ion Battery — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Disassembly and Assembly — 2Service Data — 1Ev Battery System :: 91kwh Li-Ion Battery — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Disassembly and Assembly — 1Service Data — 2Preparation. Vehicle Charging System — 1Vehicle Charging System :: Description — 1Component Parts — 2System — 1Diagnosis System (on-Board Charger) — 1Diagnosis System (dc/dc Converter) — 1Ecu Diagnosis Information — 1Vehicle Charging System — 1Charger/pd Module (on-Board Charger) — 1Cplc (cplc) — 1Dcdc (dc/dc Converter) — 1Component Parts/circuit Diagnosis — 1Symptom Diagnosis — 1Evse Inspection — 1Periodic Maintenance — 1Removal and Installation — 1Disassembly and Assembly — 1Preparation. High Voltage Cooling System — 1Description — 1Symptom Diagnosis. Overheating Cause Analysis — 1Periodic Maintenance — 1Coolant — 1Removal and Installation — 1Radiator — 1Service Data — 1Removal and Installation. Accelerator Control System — 1Reduction Gear: Re1f62a — 1Removal and Installation — 1Transaxle & Transmission :: Electric Shift — 1Description — 3Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Rear Final Drive: Rn1r62a — 1Removal and Installation — 1Preparation. Front Axle System — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data. Front Drive Shaft — 12wd — 14wd — 1Periodic Maintenance — 1Removal and Installation — 1Preparation. Front Suspension System — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Preparation. Road Wheels & Tires System — 1Description — 1System — 1Ecu Diagnosis Information. Bcm (body Control Module) — 1Tpms — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance. Road Wheels & Tires — 1Removal and Installation — 1Service Data — 1Preparation. Brake System — 1System Description — 1Component Parts — 1Ecu Diagnosis Information. Electrically-Driven Intelligent Brake Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Preparation. Parking Brake System — 1System Description — 1Component Parts — 1System — 1Ecu Diagnosis Information. Abs Actuator and Electric Unit (control Unit) — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Component Parts /circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Brake Control System :: With Vdc — 1System Description — 3Basic Inspection — 2Dtc/circuit Diagnosis — 1Symptom Diagnosis — 2Removal and Installation — 1Brake Control System :: Automatic Brake Hold — 1System Description — 3Component Parts /circuit Diagnosis — 1Removal and Installation — 1Brake Control System :: E-Step — 1System Description — 3Removal and Installation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Symptom Diagnosis — 1Rear Automatic Braking — 1System Description — 1Basic Inspection — 1Preparation. Steering System — 1System Description — 1Component Parts — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance. Steering Wheel — 1Removal and Installation — 1Service Data — 1System Description — 1Component Parts — 1Steering Control System — 1Ecu Diagnosis Information. Power Steering Control Module — 1Dtc/circuit Diagnosis — 1Component Parts /circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation. Power Steering Control Module — 1System Description — 1Removal and Installation — 1System Description — 1System — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Component Parts — 1Basic Inspection — 1Removal and Installation — 1System Description — 1System — 1Ecu Diagnosis Information. Air Bag Diagnosis Sensor Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1System Description. Description. Ventilation System — 1Removal and Installation — 1Preparation. Preparation — 1System Description — 1Basic Inspection — 1Symptom Diagnosis — 1Removal and Installation — 1Electric Compressor — 1Cooler Pipe and Hose — 1A/c Unit Assembly Cover — 1A/c Unit Assembly — 1Heater & Air Conditioning Control System :: Automatic Air Conditioning — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 2Dtc Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 2Preparation. Preparation — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1Preparation. Instrument Panel — 1Component Parts — 1System — 1Ecu Diagnosis Information. Flexible Center Storage Control Module — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Preparation. Preparation — 1Component Parts — 1System — 1Ecu Diagnosis Information. Driver Lumbar Support Control Module — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1System Description — 1System — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Manual Function Does Not Operate — 1Memory Function Does Not Operate — 1Removal and Installation — 1Preparation. Preparation — 1System Description — 1System (intelligent Key System) — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1U2141-87 Can Comm Circuit — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Automatic Back Door Operation Does Not Operate — 1Back Door Does Not Open — 1Door Does Not Lock/unlock with Door Lock and Unlock Switch — 1Removal and Installation — 1Hood — 1Radiator Core Support — 1Charge Port Lid — 1Front Fender — 1Front Door — 1Rear Door — 1Back Door — 1Hood Lock — 1Front Door Lock — 1Rear Door Lock — 1Back Door Lock — 1Outside Key Antenna — 1System Description — 1System — 1Ecu Diagnosis Information. Inverter (front), Inverter (rear), Bcm, Intelligent Key Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Preparation — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Front Passenger Side Power Window Does Not Operate — 1Rear Lh Side Power Window Does Not Operate — 1Rear Rh Side Power Window Does Not Operate — 1Removal and Installation. Power Window Main Switch — 1Preparation. Preparation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Sunroof Switch Assembly — 1Symptom Diagnosis — 1Auto Operation Does Not Operate — 1Removal and Installation — 1Preparation — 1Description — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1Service Information — 6Repair Information — 1Precaution — 1Preparation — 1Removal and Installation — 1Service Data — 1Preparation. Preparation — 1Component Parts — 1System — 1Ecu Diagnosis Information — 1Wiring Diagram. Door Mirror — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Removal and Installation — 1Exterior Lighting System :: Led Headlamp — 1System Description — 3Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance — 1Removal and Installation — 1System Description — 1System — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information. Bcm, Intelligent Key Unit — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis. Interior Lighting System Symptom — 1Removal and Installation — 1Service Data. Bulb Specifications — 1System Description — 1System — 1Ecu Diagnosis Information. Bcm, Ipdm E/r — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1System Description — 1Ecu Diagnosis Information. Bcm — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Preparation. Preparation — 1Removal and Installation. Horn — 1Preparation. Commercial Service Tools Or/and Repair Part — 1System Description — 1Component Parts — 1Ecu Diagnosis Information. Approaching Vehicle Sound for Pedestrians (vsp) Control Unit — 1Approaching Vehicle Sound for Pedestrians (vsp) — 1Vsp [approaching Vehicle Sound for Pedestrians (vsp) Control Unit] — 1Approaching Vehicle Sound for Pedestrians (vsp) System — 1Removal and Installation — 1Removal and Installation — 1Wireless Charger — 1System Description — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Removal and Installation — 1Component Parts — 1System — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information. Bcm — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Can Fundamental — 1Description — 1Trouble Diagnosis — 1Can (controller Area Network) — 1Description — 1
~35min read
  • Brake Pedal
  • Front Brake Piping
  • Rear Brake Piping
  • Brake Power Supply Backup Unit
  • Electrically-Driven Intelligent Brake Unit
  • Warning Buzzer
  • Front Brake Pad
  • Front Brake Caliper Assembly
  • Rear Brake Pad
  • Rear Brake Caliper Assembly

Brake Pedal Nissan Ariya 2023

BRAKE PEDAL : Exploded View

Brake pedal assembly Snap pin Brake pedal pad
Stop lamp switch Clevis pin
: N·m (kg-m, ft-lb)
: Apply Nissan multi-purpose Special Grease No. 2.
: Always replace after every disassembly.

BRAKE PEDAL : Removal & Installation

REMOVAL

Disconnect 12V battery negative terminal. Refer to Removal & Installation.

Remove instrument lower panel. Refer to Removal & Installation.

Remove instrument finisher B. Refer to Removal & Installation.

Remove screw .

Remove mounting nuts , and then remove bracket .

Remove negative harness mounting bolt and screw , and then remove bracket.

Disconnect the stop lamp switch harness connector.

Remove stop lamp switch 90° rotate the stop lamp switch counterclockwise.

Disconnect the accelerator pedal harness connector.

Remove snap pin and clevis pin form the clevis .

Remove harness clip from brake pedal assembly.

Remove electrically-driven intelligent brake unit mounting nuts and brake pedal assembly mounting nuts and then remove brake pedal assembly from the Nissan Ariya vehicle.

Remove accelerator pedal from brake pedal assembly. Refer to Removal & Installation.

Perform inspection after removal. Refer to Inspection and Adjustment.

INSTALLATION

Note the following, and install in the reverse order of removal.

  • Never reuse the clevis pin.

  • Apply the Nissan multi-purpose Special Grease No. 2 to the clevis pin and the mating faces. (Not necessary if grease has been already applied)

  • Never impact brake pedal such as drop and interference with tools and parts.

  • Replace brake pedal when impacting brake pedal.

  • Perform adjustment after installation. Refer to Inspection and Adjustment.

BRAKE PEDAL : Inspection and Adjustment

INSPECTION AFTER REMOVAL

Check the brake pedal assembly for bend, damage, and cracks on the welded parts. If any is found, replace brake pedal assembly.

ADJUSTMENT AFTER INSTALLATION

  • Adjust each item of brake pedal after installing the brake pedal assembly to the vehicle. Refer to Periodic Maintenance Operation .

    • Perform the release position learning of the accelerator pedal. Refer to Work Procedure.

Front Brake Piping Nissan Ariya first Gen

FRONT BRAKE PIPING : Exploded View

electrically-driven intelligent brake unit Brake tube Bracket
ABS actuator and electric unit (control unit) Lock plate Brake hose
Union bolt Copper washer
To rear brake tube. Refer to Exploded View.
: Nissan Ariya Vehicle front
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
: Always replace after every disassembly.
: Indicates that the part is connected at points with same symbol in actual Nissan Ariya vehicle.

FRONT BRAKE PIPING : Hydraulic Layout

Front disc brake ABS actuator and electric unit (control unit) Electrically-driven intelligent brake unit
Rear disc brake
Brake tube Brake hose
: Flare nut
: Union bolt

FRONT BRAKE PIPING : Removal & Installation

REMOVAL

Remove tires. Refer to Removal and Installation.

Drain brake fluid. Refer to Draining.

Loosen the flare nut with a flare nut wrench (A) and separate the brake tube from the brake hose .

Remove the union bolt and copper washers , and remove the brake hose from the brake caliper assembly.

Remove the lock plate and remove the brake hose.

INSTALLATION

Assemble the union bolt and the copper washer to the brake hose .

Align the brake hose pin with the brake caliper assembly projection , and tighten the union bolt to the specified torque.

Install the brake tube to the brake hose , temporarily tighten the flare nut by hand until it does not rotate further, and fix the brake hose to the bracket with the lock plate .

Tighten the flare nut to the specified torque with a flare nut torque wrench (A).

Refill with new brake fluid and perform the air bleeding. Refer to Bleeding Brake System.

Install tires. Refer to Removal and Installation.

Perform inspection after installation. Refer to Inspection.

FRONT BRAKE PIPING : Inspection

INSPECTION AFTER INSTALLATION

Check the brake hoses and tubes for the following: no scratches; no twist and deformation; no interference with other components when steering the steering wheel; no looseness at connections.

*: Fuel, engine coolant and lubricant are quantity to specified. Spare tire, jack, hand tools and mats are brought out of Nissan Ariya vehicle.

Depress the brake pedal with a force of 785 N (80 kg, 176 lb) and hold down the pedal for approximately 5 seconds with the engine running. Check for any fluid leakage.

Rear Brake Piping Nissan Ariya 1st generation

REAR BRAKE PIPING : Exploded View

2WD MODELS

Brake tube RH Brake tube LH Bracket
Lock plate Bracket Aluminum washer
Union bolt Brake hose
To front brake tube. Refer to Exploded View.
: Nissan Ariya Vehicle front
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
: Always replace after every disassembly.
: Indicates that the part is connected at points with same symbol in actual Nissan Ariya vehicle.

4WD MODELS

Brake tube RH Brake tube LH Bracket
Lock plate Bracket Aluminum washer
Union bolt Brake hose
To front brake tube. Refer to Exploded View.
: Nissan Ariya Vehicle front
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
: Always replace after every disassembly.
: Indicates that the part is connected at points with same symbol in actual Nissan Ariya vehicle.

REAR BRAKE PIPING : Hydraulic Layout

Front disc brake ABS actuator and electric unit (control unit) Electrically-driven intelligent brake unit
Rear disc brake
Brake tube Brake hose
: Flare nut
: Union bolt

REAR BRAKE PIPING : Removal & Installation

REMOVAL

Remove tires. Refer to Removal and Installation.

Remove the lock plate , then remove the brake hose from the brake tube bracket.

Loosen the flare nut with a flare nut wrench (A) and separate the brake tube from the brake hose .

Remove the lock plate , then remove the brake tube B from the brake tube bracket.

Remove the union bolt and aluminum washers , and remove the brake hose from the brake caliper assembly.

INSTALLATION

Assemble the union bolt and the aluminum washers to the brake hose.

Align the brake hose L-pin with the brake caliper assembly hole , and tighten the union bolt to the specified torque.

Install the brake hose to the brake tube, temporarily tighten the flare nut by hand until it does not rotate further, and fix the brake hose to the brake hose bracket with the lock plate.

Tighten the flare nut to the specified torque with a flare nut torque wrench (A).

Refill with new brake fluid and perform the air bleeding. Refer to Bleeding Brake System.

Install tires. Refer to Removal and Installation.

Perform inspection after installation. Refer to Inspection.

REAR BRAKE PIPING : Inspection

INSPECTION AFTER INSTALLATION

Check the brake hoses and tubes for the following: no scratches; no twist and deformation; no looseness at connections.

*: Fuel, engine coolant and lubricant are quantity to specified. Spare tire, jack, hand tools and mats are brought out of Nissan Ariya vehicle.

Depress the brake pedal with a force of 785 N (80 kg, 176 lb) and hold down the pedal for approximately 5 seconds with the engine running. Check for any fluid leakage.

Brake Power Supply Backup Unit Nissan Ariya 2023

BRAKE POWER SUPPLY BACKUP UNIT : Exploded View

Brake power supply backup unit Bracket
: N·m (kg-m, in-lb)

BRAKE POWER SUPPLY BACKUP UNIT : Removal & Installation

REMOVAL

Power switch OFF and disconnect CONSULT from DDL2 diagnosis connector.

Check that room lamps are turned OFF after closing all doors including back door, and then wait for 3 minutes or more at out side of Nissan Ariya vehicle.

Remove luggage side lower finisher (right).Refer to Removal & Installation.

Disconnect brake power supply backup unit harness connector.

Remove nut and then remove brake power supply backup unit assembly .

Remove bracket from brake power supply backup unit.

INSTALLATION

Note the following, and install in the reverse order of removal.

  • Align the direction of alphabet letters on the brake power supply backup unit with the direction of the same alphabet letters on the bracket .

  • When installing bracket to brake power supply backup unit , make sure to insert protrusion of brake power supply backup to lock hole of bracket unit protrudes from the opposite side of the lock hole.

Electrically-Driven Intelligent Brake Unit Nissan Ariya 2023

ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Exploded View

Reservoir cap Oil strainer Electrically-driven intelligent brake unit
Clevis Gasket
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.

ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation

REMOVAL

Perform inspection before removal. Refer to Inspection and Adjustment.

Power switch OFF and disconnect CONSULT from DDL2 diagnosis connector.

Check that room lamps are turned OFF after closing all doors including back door, and then wait for 3 minutes or more at out side of Nissan Ariya vehicle.

Disconnect negative terminal of 12 V battery. Refer to Removal and Installation.

Drain brake fluid. Refer to Draining.

Remove cowl top member. Refer to Removal & Installation.

Separate the brake tube from electrically-driven intelligent brake unit with a flare nut wrench (A).

Remove brake fluid level switch as follows;Slide connector lock to right (1) of Nissan Ariya vehicle. While connector lock is pushed in , disconnect brake fluid level switch harness connector in lateral direction (2) of Nissan Ariya vehicle.

Disconnect electrically-driven intelligent brake unit harness connector as follows;

Slide lever lock to right of Nissan Ariya vehicle and unlock it. While connector lock is pushed in, move lever to arrow direction. Disconnect electrically-driven intelligent brake unit harness connector.

Disconnect stroke sensor harness connector as follows;Slide connector lock to right (1) of Nissan Ariya vehicle. While connector lock (2) is pushed in , disconnect stroke sensor harness connector in the front direction (3) of Nissan Ariya vehicle.

Remove stroke sensor harness clip behind brake master cylinder .

Remove snap pin and clevis pin from clevis.

Remove brake pedal bracket assembly. Refer to. Removal & Installation.

Remove electrically-driven intelligent brake unit mounting nut.

Remove electrically-driven intelligent brake unit.

Remove gasket from electrically-driven intelligent brake unit.

INSTALLATION

  • If electrically-driven intelligent brake unit is dropped or impacted, replace electrically-driven intelligent brake unit assembly.

  • When installing, hold part of electrically-driven intelligent brake unit.

  • Never apply grease or lubricant to the parts that contact with brake fluid and rubber parts.

  • Never spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe it off immediately and wash with water if it gets on a painted surface. For brake component parts, never wash them with water.

  • Never depress brake pedal during removal and installation of brake hose because brake fluid may scatter.

Note the following, and install in the reverse order of removal.

  • Never crush threads of stud bolts of the electrically-driven intelligent brake unit. When installing diagonally, the dash panel may damage the threads.

  • Never deform brake tube when installing electrically-driven intelligent brake unit.

  • Never reuse clevis pin.

  • Temporarily tighten flare nut of brake tube by hand, and then install it to the electrically-driven intelligent brake unit to the specified tightening torque using flare nut torque wrench (commercial tool) (A). Refer to Exploded View.

  • After installing electrically-driven intelligent brake unit harness connector , move lever part in the direction until it locks, and push in lock part to lock it securely.

  • Install stroke sensor harness connector as follows;

    1. Insert connector lock into electrically-driven intelligent brake unit (1).

    2. Push in the connector lock in the (2) direction and securely lock.

  • Install brake fluid level switch harness connector as follows;

    1. Insert connector to brake fluid level switch.

    2. Push in connector lock in the (2) direction and securely lock.

  • Perform air bleeding. Refer to Air Bleeding.

  • Check brake pedal for each item, adjust when there is deviation from the specified value. Refer to Periodic Maintenance Operation.

ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Inspection

INSPECTION BEFORE REMOVAL

Check brake fluid level switch. Refer to DTC Diagnosis Procedure.

INSPECTION AFTER REMOVAL

Check the following items, and replace the part if necessary.

  • Check for damage, deformation, interference with the other parts, and looseness of connection.

  • Check for fluid leakage from connection. Refer to Inspection

INSPECTION AFTER INSTALLATION

Must be performed additional service when replacing electrically-driven intelligent brake unit. Refer to Description.

Warning Buzzer Nissan Ariya 2023

WARNING BUZZER : Exploded View

Warning buzzer Clip Screw
Bracket

WARNING BUZZER : Removal & Installation

REMOVAL

Remove integrated interface display. Refer. Removal & Installation.

Disconnect warning buzzer harness connector .

Remove mounting screw and the remove warning buzzer .

INSTALLATION

Note the following, and install in the reverse order of removal.

Front Brake Pad Nissan Ariya 2026

FRONT BRAKE PAD : Exploded View

FOR 31 SIZE NAO MODELS

Cylinder body Inner shim Inner pad (with pad wear sensor)
Torque member Pad retainer Outer pad (with pad wear sensor)
Outer shim
: Nissan Ariya Vehicle front
: N·m (kg-m, ft-lb)
: Nissan disc brake shim grease

FOR 36 SIZE NAO MODELS

Cylinder body Inner shim Inner pad (with pad wear sensor)
Torque member Pad retainer (VHB foil) Outer pad
Outer shim
: Nissan Ariya Vehicle front
: N·m (kg-m, ft-lb)
: Nissan disc brake shim grease

FRONT BRAKE PAD : Removal & Installation

FOR NAO 31 SIZE MODELS

REMOVAL

Remove tires. Refer to Removal and Installation.

Remove sliding pin bolt (lower side).

Hang cylinder body with suitable wire not to stretch brake hose.

Remove brake pads, shims, and pad retainer from torque member.

Perform inspection after removal. Refer to Inspection and Adjustment.

INSTALLATION

Install pad retainers to torque members if pad retainers are removed before.

Apply Nissan disc brake shim grease to the matching surfaces between brake pad and shim cover , and install shim covers to brake pad.

Install brake pads to torque member.

Install cylinder body to torque member.

Install slide pin bolt (lower side) and tighten to the specified torque.

Check front disc brake for dragging, while depressing brake pedal several times. Refer to Inspection and Adjustment.

Install tires. Refer to Removal and Installation.

FOR NAO 36 SIZE MODELS

REMOVAL

Remove tires. Refer to Removal and Installation.

Remove sliding pin bolt (lower side).

Hang cylinder body with suitable wire not to stretch brake hose.

Remove brake pads, shims, and pad retainer from torque member.

Perform inspection after removal. Refer to Inspection and Adjustment.

INSTALLATION

Install pad retainers to torque members if pad retainers are removed before.

Install pad retainer with new VHB foil on pad retainer.

Apply Nissan disc brake shim grease to the matching surfaces between brake pad and shim cover , and install shim covers to brake pad.

Install brake pads to torque member.

Install cylinder body to torque member.

Install slide pin bolt (lower side) and tighten to the specified torque.

Check front disc brake for dragging, while depressing brake pedal several times. Refer to Inspection and Adjustment.

Install tires. Refer to Removal and Installation.

FRONT BRAKE PAD : Inspection

INSPECTION AFTER REMOVAL

  • Replace the shims and shim covers if rust is excessively occurred.

  • Eliminate rust on pad retainers and the torque member. Replace them if rust is excessively occurred.

INSPECTION AFTER INSTALLATION

Check front disc brake for a dragging. If any drag is felt, follow the procedure described below.

Remove brake pads. Refer to Removal and Installation.

Return pistons of caliper. Refer to Removal and Installation.

Install brake pads. Refer to Removal and Installation.

Depress brake pedal several times.

Check front disc brake for a dragging again. If any drag is felt, disassemble cylinder body. Replace if necessary. Refer to Disassembly and Assembly.

If brake pads are replaced or ground, or if braking force is felt strange, perform break-in work. Refer to Periodic Maintenance Operation.

Front Brake Caliper Assembly Nissan Ariya SUV

FRONT BRAKE CALIPER ASSEMBLY : Exploded View

FOR NAO 31 SIZE MODELS

REMOVAL

Brake caliper assembly
: N·m (kg-m, ft-lb)

DISASSEMBLY

Cap Bleeder valve Cylinder body
Piston seal Sliding pin Piston
Sliding pin boot Piston boot Torque member
Bushing
: Nissan Ariya Vehicle front
: N·m (kg-m, in-lb)
: NISSAN rubber grease.
: NISSAN brake fluid No.2500
: Always replace after every disassembly.

FOR NAO 36 SIZE MODELS

REMOVAL

Brake caliper assembly
: N·m (kg-m, ft-lb)

DISASSEMBLY

Cap Bleeder valve Cylinder body
Piston seal Sliding pin Piston
Sliding pin boot Piston boot Torque member
Bushing
: Nissan Ariya Vehicle front
: N·m (kg-m, in-lb)
: NISSAN rubber grease.
: NISSAN brake fluid No.2500
: Always replace after every disassembly.

FRONT BRAKE CALIPER ASSEMBLY : Removal & Installation

REMOVAL

Remove tires. Refer to Removal and Installation.

Fix the disc rotor using wheel nuts.

Drain brake fluid. Refer to Draining.

Remove union bolts and copper washer and then separate brake hose from brake caliper assembly. Refer to Removal & Installation

Remove torque member mounting bolt and then remove brake caliper assembly.

INSTALLATION

Install disc rotor. Refer to Removal & Installation.

Install brake caliper assembly to steering knuckle and tighten torque member mounting bolt to the specified torque.

Install copper washers and brake hose to brake caliper and tighten union bolt to the specified torque. Refer to Removal & Installation.

Perform air bleeding. Refer to Air Bleeding.

Check front disc brake for dragging. Refer to Inspection.

Install tires. Refer to Removal and Installation.

Perform inspection after installation. Refer to Inspection.

FRONT BRAKE CALIPER ASSEMBLY : Disassembly & Assembly

DISASSEMBLY

Remove sliding pin bolts and then remove cylinder body from torque member.

Remove sliding pin boots from torque member.

Remove bushing from sliding pin .

Place a wooden block as shown in the figure, and blow air into union bolt mounting hole to remove pistons and piston boots.

Remove piston seals from cylinder body using seal pick tool.

Remove bleeder valve and cap.

Perform inspection after disassembly. Refer to Inspection.

ASSEMBLY

Install bleeder valve and cap.

Apply Nissan rubber grease to piston seals , and install them to cylinder body.

Apply Nissan rubber grease to piston boots . Cover piston end with piston boot, and then install cylinder side lip of piston boot securely into groove on cylinder body.

Apply new brake fluid to pistons . Push piston into cylinder body and then install piston-side lip of piston boot into the piston groove.

Apply rubber grease to mating faces between sliding pin and bushing , and install bushing to sliding pin.

Apply rubber grease to mating faces between sliding pins and sliding pin boots , and install sliding pins and sliding pin boots to torque member .

Install cylinder body to torque member and tighten sliding pin bolts to the specified torque.

FRONT BRAKE CALIPER ASSEMBLY : Inspection

INSPECTION AFTER DISASSEMBLY

Check the following items and replace if necessary.

Cylinder Body

Check cylinder inner wall for rust, wear, cracks or damage.

Torque Member

Check the torque member for rust, wear, cracks or damage.

Pistons

Check surface of piston for rust, wear, cracks or damage.

Sliding Pin, Sliding Pin Boot and Bushing

Check sliding pins, sliding pin boots and bushing for rust, wear, cracks or damage.

INSPECTION AFTER INSTALLATION

Check front disc brake for dragging. If any drag is found, follow the procedure described below.

Remove brake pads. Refer to Removal and Installation.

Return pistons caliper. Refer to Removal and Installation.

Install brake pad. Refer to Removal and Installation.

Depress the brake pedal several times.

Check front disc brake for dragging again. When any drag is found, disassemble the cylinder body and replace if necessary. Refer to Disassembly and Assembly.

If brake pads are replaced or ground, or if braking force is felt strange, perform break-in work. Refer to Periodic Maintenance Operation .

Rear Brake Pad Nissan Ariya SUV

REAR BRAKE PAD : Exploded View

Cylinder body Inner shim cover Inner shim
Inner pad (with pad wear sensor) Pad retainer Torque member
Outer pad (with pad wear sensor) Outer shim cover
: Nissan Ariya Vehicle front
: N·m (kg-m, ft-lb)

REAR BRAKE PAD : Removal & Installation

REMOVAL

Release parking brake.

Must be performed additional service when replacing brake pad or rear brake caliper. Refer to Description.

Remove tires. Refer to Removal and Installation.

Disconnect parking brake actuator harness connector .

Fix sliding pin with spanner wrench (commercial tool) (A) and remove sliding pin bolt.

Remove cylinder body from torque member, and hang cylinder body with suitable wire (A) to prevent brake hose for stretching.

Remove brake pads, shims and shim covers from torque member.

Perform inspection after removal. Refer to Inspection.

INSTALLATION

Install pad retainers to torque members if pad retainers are removed before.

Install inner shim and inner shim cover to inner pad.

Install outer cover to outer pad.

Install brake pad to torque member.

Install cylinder body to torque member.

Install sliding pin bolt to cylinder body and tighten them to the specified torque.

Must be performed additional service when removing and replacing brake pad and rear brake caliper. Refer to Description.

Depress the brake pedal several times to check that no drag feel is present for the rear disc brake. Refer to Inspection.

Install tires. Refer to Removal and Installation.

Perform inspection after installation. Refer to Inspection.

REAR BRAKE PAD : Inspection

INSPECTION AFTER REMOVAL

  • Replace the shims and shim covers if rust is excessively attached.

  • Eliminate rust on the pad and the torque member. Replace them if rust is excessively attached.

INSPECTION AFTER INSTALLATION

  • When replacing rear brake pad or when returning piston of rear brake caliper, perform the following procedure.

    • Adjust initial position. Refer to Work Procedure.

    • Must be performed additional service when removing and replacing rear brake pad and rear brake caliper. Refer to Description.

  • Check a drag of rear disc brake, if any drag is felt, follow the procedure described below.

    1. Must be performed additional service when removing and replacing rear brake pad and rear Refer to Description.

    2. Depress the brake pedal several times.

    3. Check a drag of rear disc brake again. If any drag is felt, disassemble the cylinder body and replace if necessary. Refer to Removal and Installation.

  • If brake pads are replaced or ground, or if braking force is felt strange, perform break-in work. Refer to Periodic Maintenance Operation.

Rear Brake Caliper Assembly Nissan Ariya: FE0

REAR BRAKE CALIPER ASSEMBLY : Exploded View

REMOVAL

Brake caliper assembly
: N·m (kg-m, ft-lb)

DISASSEMBLY

Cap Bleeder valve Cylinder body
Sliding pin Sliding pin boot Bushing
Torque member
: Nissan Ariya Vehicle front
: N·m (kg-m, in-lb)
: NISSAN rubber grease.

REAR BRAKE CALIPER ASSEMBLY : Removal & Installation

REMOVAL

Release parking brake.

Must be performed additional service when removing and replacing brake pad or rear brake caliper. Refer to Description.

Remove tires. Refer to Removal and Installation.

Fix disc rotor using wheel nut.

Drain brake fluid. Refer to Draining.

Separate brake hose from brake caliper assembly. Refer to Removal and Installation.

Remove parking brake actuator harness connector and bracket mounting bolt .

Remove torque member mounting bolt and then remove brake caliper assembly.

When remove disc rotor. Refer to Removal and Installation.

INSTALLATION

Install disc rotor. Refer to Removal and Installation.

Install brake caliper assembly to axle housing and then tighten torque member mounting bolts to the specified torque.

Install brake hose and copper washers to brake caliper assembly. Refer to Removal and Installation.

Install parking brake actuator harness connector and bracket mounting bolt .

Must be performed additional service when removing and replacing brake pad or brake caliper. Refer to Description.

Perform air bleeding. Refer to Bleeding.

Check drag of rear disc brake. If any drag is felt. Refer to Inspection.

Install tires. Refer to Removal and Installation.

Perform inspection after installation. Refer to Inspection.

REAR BRAKE CALIPER ASSEMBLY : Disassembly & Assembly

DISASSEMBLY

Remove sliding pin bolt, and then remove cylinder body from torque member. Refer to Removal and Installation.

Remove sliding pins and sliding pin boots from torque member.

Remove bushing from sliding pin .

Remove bleeder valve and cap.

Perform inspection after disassembly. Refer to Inspection.

ASSEMBLY

Install bleeder valve and cap.

Apply rubber grease to mating faces between sliding pin bolt and bushing , and install bushing to sliding pin.

Apply Nissan rubber grease to mating faces between sliding pins and sliding pin boots , and then install sliding pins and sliding pin boots to torque member .

Install cylinder body to torque member and tighten sliding pin bolts to the specified torque. Refer to Exploded View

Perform inspection after installation. Refer to Inspection.

REAR BRAKE CALIPER ASSEMBLY : Inspection

INSPECTION AFTER DISASSEMBLY

Check the following items and replace if necessary.

Cylinder Body

Check cylinder inner wall for rust, wear, cracks or damage.

Torque Member

Check torque member for rust, wear, cracks or damage.

Piston

Check piston for rust, wear, cracks or damage.

Sliding Pin, Sliding Pin Boot and Bushing

Check sliding pins, sliding pin boots and bushing for rust, wear, cracks or damage.

INSPECTION AFTER INSTALLATION

  • When replacing rear brake caliper or when returning piston of rear brake caliper, perform the following procedure.

    • Adjust initial position. Refer to Work Procedure

      .
    • Must be performed additional service when removing and replacing rear brake pad and rear brake caliper. Refer to Description.

  • Check drag of rear disc brake. If any drag is felt, follow the procedure described below.

    1. Performed additional service when removing and replacing rear brake pad and rear brake caliper. Refer to. Work Procedure.

    2. Depress the brake pedal several times.

    3. Check drag of rear disc brake again. When any drag is felt, replace cylinder body. Refer to Removal and Installation.

  • If brake pads are replaced or ground, or if braking force is felt strange, perform break-in work. Refer to Periodic Maintenance Operation.