Dtc/circuit Diagnosis
- Power Supply and Ground Circuit (center Console Finisher)
- Console Slide Switch
- Console Slide Motor
- Flexible Center Storage Motor
- Flexible Center Storage Open/close Switch Circuit
- Flexible Center Storage Full Close/open Switch Circuit
- Vehicle Speed Signal Circuit
- Close Reminder Circuit
Power Supply and Ground Circuit (center Console Finisher) Nissan Ariya SUV
Diagnosis Procedure
CHECK FUSE
Check that the following fuses are not blown (open).
| Location | Fuse No. | Capacity |
|---|---|---|
| Fuse block (J/B) | 53 | 10A |
| 8 | 10A |
Is the fuse blown (open)?
YES>>Replace the blown (open) fuse after repairing the affected circuit if a fuse is blown (open).
NO>>GO TO 2.
CHECK POWER SUPPLY CIRCUIT
Power switch OFF.
Disconnect center console finisher connector.
Check voltage between center console finisher harness connector and ground.
+ - Condition Voltage Center console finisher Connector Terminal M204 1 Ground Power switch OFF (auto ACC status) or ON Battery voltage Other than above 0 V 2 ON Battery voltage Other than above 0 V
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair the harness or connector.
CHECK GROUND CIRCUIT
Power switch OFF.
Check continuity between center console finisher harness connector and ground.
| Center console finisher | ― | Continuity | |
|---|---|---|---|
| Connector | Terminal | ||
| M204 | 16 | Ground | Existed |
Is the inspection result normal?
YES>>INSPECTION END
NO>>Repair the harness or connector.
Console Slide Switch Nissan Ariya
Component Function Check
CHECK CONSOLE SLIDE SWITCH FUNCTION
Power switch ON.
Select “DRIVER SEAT” using CONSULT.
Select “Console slide switch (Forward)” and "Console slide switch (Backward)" in “Data monitor” mode.
Check that the function operates normally according to the following conditions.
Monitor item Condition Status Console slide switch (Forward) Console slide switch (forward side) Push On Release Off Console slide switch (Backward) Console slide switch (backward side) Push On Release Off
Is the inspection result normal?
YES>>Console slide switch is normal.
NO>>Refer to Diagnosis Procedure.
Diagnosis Procedure
CHECK CONSOLE SLIDE SWITCH POWER SUPPLY VOLTAGE
Power switch OFF.
Disconnect console slide switch connector.
Check voltage between console slide switch harness connector and ground.
+ − Voltage
(Approx.)Console slide switch Connector Terminal M213 1 Ground 5 V
Is the inspection result normal?
YES>>GO TO 2.
NO>>GO TO 3.
CHECK CONSOLE SLIDE SWITCH GROUND CIRCUIT
Disconnect driver seat control unit connector.
Check continuity between console slide switch harness connector and driver seat control unit harness connector.
Console slide switch Driver seat control unit Continuity Connector Terminal Connector Terminal M213 4 B313 32 Existed
Is the inspection result normal?
YES>>GO TO 4.
NO>>Repair the harness or connector.
CHECK CONSOLE SLIDE SWITCH POWER SUPPLY CIRCUIT
Disconnect driver seat control unit connector.
Check continuity between console slide switch harness connector and driver seat control unit harness connector.
Console slide switch Driver seat control unit Continuity Connector Terminal Connector Terminal M213 1 B313 25 Existed
Is the inspection result normal?
YES>>Replace driver seat control unit. Refer to Removal and Installation.
NO>>Repair the harness or connector.
CHECK CONSOLE SLIDE SWITCH
Check console slide switch. Refer to Component Inspection.
Is the inspection result normal?
YES>>Replace driver seat control unit. Refer to Removal and Installation.
NO>>Replace console slide switch. Refer to Removal & Installation.
Component Inspection
CHECK CONSOLE SLIDE SWITCH
Power switch OFF.
Disconnect console slide switch connector.
Check continuity between console slide switch terminals.
Console slide switch Condition Resistance (Ω) Terminal 1 4 Console slide switch Operate forward side switch 399 - 455 Operate backward side switch 241 - 287 Release 7276 - 8235
Is the inspection result normal?
YES>>INSPECTION END
NO>>Replace console slide switch. Refer to Removal & Installation.
Console Slide Motor Nissan Ariya first Gen
Component Function Check
CHECK CONSOLE SLIDE MOTOR FUNCTION
Power switch ON.
Select “DRIVER SEAT” using CONSULT.
Select “Console slide motor” in “Active test” mode.
Check that the function operates normally according to the following conditions.
Test item Operation Console slide motor Up Console slide upper Forward Down Backward Stop Stop
Is the inspection result normal?
YES>>Console slide motor is normal.
NO>>Refer to Diagnosis Procedure.
Diagnosis Procedure
CHECK CONSOLE SLIDE MOTOR OPERATION SIGNAL
Power switch OFF.
Disconnect console slide motor connector.
Check voltage between console slide motor harness connector and ground.
+ − Condition Voltage
(Approx.)Console slide motor Connector Terminal M201 1 Ground Console slide upper Backward operation 13.5 V Other than above 0 – 1 V 2 Forward operation 13.5 V Other than above 0 – 1 V
Is the inspection result normal?
YES>>Replace center console assembly. Refer to Removal & Installation.
NO>>GO TO 2.
CHECK CONSOLE SLIDE MOTOR OPERATION SIGNAL CIRCUIT
Disconnect driver seat control unit connector.
Check continuity between console slide motor harness connector and driver seat control unit harness connector.
Console slide motor Driver seat control unit Continuity Connector Terminal Connector Terminal M201 1 B465 41 Existed 2 42
Is the inspection result normal?
YES>>Replace driver seat control unit. Refer to Removal and Installation.
NO>>Repair the harness or connector.
Flexible Center Storage Motor Nissan Ariya SUV
Diagnosis Procedure
CHECK FLEXIBLE CENTER STORAGE MOTOR OPERATION SIGNAL
Power switch OFF.
Disconnect flexible center storage motor connector.
Check voltage between flexible center storage motor harness connector and ground.
+ - Condition Voltage
(Approx.)Flexible center storage motor Connector Terminal M632 1 Ground Flexible center storage OPEN/CLOSE switch Push OPEN switch 12 V Release 0.13 V 3 Push CLOSE switch 12 V Release 0.13 V
Is the inspection result normal?
YES>>Replace flexible center storage assembly. Refer to Removal & Installation.
NO>>GO TO 2.
CHECK FLEXIBLE CENTER STORAGE MOTOR OPERATION SIGNAL CIRCUIT
Disconnect flexible center storage control module connector.
Check continuity between flexible center storage motor harness connector and flexible center storage control module harness connector.
Flexible center storage motor Flexible center storage control module Continuity Connector Terminal Connector Terminal M632 1 M622 14 Existed 3 18
Is the inspection result normal?
YES>>Replace flexible center storage assembly. Refer to Removal & Installation.
NO>>Repair the harness or connector.
Flexible Center Storage Open/close Switch Circuit Nissan Ariya: FE0
Diagnosis Procedure
CHECK FLEXIBLE CENTER STORAGE OPEN/CLOSE SWITCH SIGNAL
Power switch OFF.
Check voltage between flexible center storage control module harness connector and ground.
+ - Condition Voltage
(Approx.)Flexble center storage control module Connector Terminal M621 8 Ground Flexible center storage OPEN/CLOSE switch Push OPEN switch 5 V Release 0 V 9 Push CLOSE switch 5 V Release 0 V
Is the inspection result normal?
YES>>Check intermittent incident. Refer to Intermittent Incident.
NO>>GO TO 2.
CHECK FLEXIBLE CENTER STORAGE OPEN/CLOSE SWITCH SIGNAL CIRCUIT
Disconnect flexble center storage control module connector and center console finisher connector.
Check continuity between flexble center storage control module harness connector and center console finisher harness connector.
Flexble center storage control module Center console finisher Continuity Connector Terminal Connector Terminal M621 8 M204 8 Existed 9 9
Is the inspection result normal?
YES>>Replace center console finisher. Refer to Removal & Installation.
NO>>Repair the harness or connector.
Flexible Center Storage Full Close/open Switch Circuit Nissan Ariya first Gen
Diagnosis Procedure
CHECK FLEXIBLE CENTER STORAGE FULL CLOSE/OPEN SWITCH SIGNAL
Power switch ON.
Check voltage between flexible center storage control module harness connector and ground.
+ - Condition Voltage
(Approx.)Flexible center storage control module Connector Terminal M621 5 Ground Flexible center storage lid Full close 0 V Other than above 5 V 6 Full open 0 V Other than above 5 V
Is the inspection result normal?
YES>>Check intermittent incident. Refer to Intermittent Incident.
NO>>Replace flexible center storage assembly. Refer to Removal & Installation.
Vehicle Speed Signal Circuit Nissan Ariya first Gen
Diagnosis Procedure
CHECK VEHICLE SPEED SIGNAL
Power switch OFF.
Disconnect flexible center storage control module connector and combination meter connector.
Check continuity between flexible center storage control module harness connector and combination meter harness connector.
Flexible center storage control module Combination meter Continuity Connector Terminal Connector Terminal M621 3 M98 12 Existed Check continuity between flexible center storage control module harness connector and ground.
Flexible center storage control module ― Continuity Connector Terminal M621 3 Ground Not existed
Is the inspection result normal?
YES>>Replace integrated interface display (combination meter). Refer to Removal and Installation.
NO>>Repair the harness or connector.
Close Reminder Circuit Nissan Ariya: FE0
Diagnosis Procedure
CHECK CLOSE REMINDER SIGNAL
Check voltage between center console finisher harness connector and ground.
| + | - | Condition | Voltage (Approx.) | ||
|---|---|---|---|---|---|
| Center console finisher | |||||
| Connector | Terminal | ||||
| M204 | 7 | Ground | Nissan Ariya Vehicle speed | More than 15 km/h | 1.2 V |
| Less than 15 km/h | 0 V | ||||
Is the inspection result normal?
YES>>Replace center console finisher. Refer to Removal & Installation.
NO>>GO TO 2.
CHECK CLOSE REMINDER SIGNAL CIRCUIT
Disconnect flexible center storage control module connector and center console finisher connector.
Check continuity between flexible center storage control module harness connector and center console finisher harness connector.
Flexible center storage control module Center console finisher Continuity Connector Terminal Connector Terminal M621 10 M204 7 Existed Check continuity between flexible center storage control module harness connector and ground.
Flexible center storage control module ― Continuity Connector Terminal M621 10 Ground Not existed
Is the inspection result normal?
YES>>Replace flexible center storage assembly. Refer to Removal & Installation.
NO>>Repair the harness or connector.