Removal and Installation

In this manual: Removal and Installation
How to Use This Manual — 1Precautions — 1Preparation — 1Vehicle Information — 1Basic Inspection — 1Preparation. Commercial Service Tools Or/and Repair Part — 1Description — 1Component Parts — 1System — 1Diagnosis System (vcm) — 1Ecu Diagnosis Information. Vcm — 1Ev Control System — 1Ev/hev (vcm) — 1Component Parts /circuit Diagnosis — 1Ev Control System — 1Periodic Maintenance. Ev System Warning Lamp — 1Removal and Installation. Vcm — 1Traction Motor System :: Front Traction Motor — 1Preparation — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Traction Motor System :: Rear Traction Motor — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Ev Battery System :: 66kwh Li-Ion Battery — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Disassembly and Assembly — 2Service Data — 1Ev Battery System :: 91kwh Li-Ion Battery — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Disassembly and Assembly — 1Service Data — 2Preparation. Vehicle Charging System — 1Vehicle Charging System :: Description — 1Component Parts — 2System — 1Diagnosis System (on-Board Charger) — 1Diagnosis System (dc/dc Converter) — 1Ecu Diagnosis Information — 1Vehicle Charging System — 1Charger/pd Module (on-Board Charger) — 1Cplc (cplc) — 1Dcdc (dc/dc Converter) — 1Component Parts/circuit Diagnosis — 1Symptom Diagnosis — 1Evse Inspection — 1Periodic Maintenance — 1Removal and Installation — 1Disassembly and Assembly — 1Preparation. High Voltage Cooling System — 1Description — 1Symptom Diagnosis. Overheating Cause Analysis — 1Periodic Maintenance — 1Coolant — 1Removal and Installation — 1Radiator — 1Service Data — 1Removal and Installation. Accelerator Control System — 1Reduction Gear: Re1f62a — 1Removal and Installation — 1Transaxle & Transmission :: Electric Shift — 1Description — 3Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Rear Final Drive: Rn1r62a — 1Removal and Installation — 1Preparation. Front Axle System — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data. Front Drive Shaft — 12wd — 14wd — 1Periodic Maintenance — 1Removal and Installation — 1Preparation. Front Suspension System — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Preparation. Road Wheels & Tires System — 1Description — 1System — 1Ecu Diagnosis Information. Bcm (body Control Module) — 1Tpms — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance. Road Wheels & Tires — 1Removal and Installation — 1Service Data — 1Preparation. Brake System — 1System Description — 1Component Parts — 1Ecu Diagnosis Information. Electrically-Driven Intelligent Brake Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Preparation. Parking Brake System — 1System Description — 1Component Parts — 1System — 1Ecu Diagnosis Information. Abs Actuator and Electric Unit (control Unit) — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Component Parts /circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Brake Control System :: With Vdc — 1System Description — 3Basic Inspection — 2Dtc/circuit Diagnosis — 1Symptom Diagnosis — 2Removal and Installation — 1Brake Control System :: Automatic Brake Hold — 1System Description — 3Component Parts /circuit Diagnosis — 1Removal and Installation — 1Brake Control System :: E-Step — 1System Description — 3Removal and Installation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Symptom Diagnosis — 1Rear Automatic Braking — 1System Description — 1Basic Inspection — 1Preparation. Steering System — 1System Description — 1Component Parts — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance. Steering Wheel — 1Removal and Installation — 1Service Data — 1System Description — 1Component Parts — 1Steering Control System — 1Ecu Diagnosis Information. Power Steering Control Module — 1Dtc/circuit Diagnosis — 1Component Parts /circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation. Power Steering Control Module — 1System Description — 1Removal and Installation — 1System Description — 1System — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Component Parts — 1Basic Inspection — 1Removal and Installation — 1System Description — 1System — 1Ecu Diagnosis Information. Air Bag Diagnosis Sensor Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1System Description. Description. Ventilation System — 1Removal and Installation — 1Preparation. Preparation — 1System Description — 1Basic Inspection — 1Symptom Diagnosis — 1Removal and Installation — 1Electric Compressor — 1Cooler Pipe and Hose — 1A/c Unit Assembly Cover — 1A/c Unit Assembly — 1Heater & Air Conditioning Control System :: Automatic Air Conditioning — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 2Dtc Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 2Preparation. Preparation — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1Preparation. Instrument Panel — 1Component Parts — 1System — 1Ecu Diagnosis Information. Flexible Center Storage Control Module — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Preparation. Preparation — 1Component Parts — 1System — 1Ecu Diagnosis Information. Driver Lumbar Support Control Module — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1System Description — 1System — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Manual Function Does Not Operate — 1Memory Function Does Not Operate — 1Removal and Installation — 1Preparation. Preparation — 1System Description — 1System (intelligent Key System) — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1U2141-87 Can Comm Circuit — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Automatic Back Door Operation Does Not Operate — 1Back Door Does Not Open — 1Door Does Not Lock/unlock with Door Lock and Unlock Switch — 1Removal and Installation — 1Hood — 1Radiator Core Support — 1Charge Port Lid — 1Front Fender — 1Front Door — 1Rear Door — 1Back Door — 1Hood Lock — 1Front Door Lock — 1Rear Door Lock — 1Back Door Lock — 1Outside Key Antenna — 1System Description — 1System — 1Ecu Diagnosis Information. Inverter (front), Inverter (rear), Bcm, Intelligent Key Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Preparation — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Front Passenger Side Power Window Does Not Operate — 1Rear Lh Side Power Window Does Not Operate — 1Rear Rh Side Power Window Does Not Operate — 1Removal and Installation. Power Window Main Switch — 1Preparation. Preparation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Sunroof Switch Assembly — 1Symptom Diagnosis — 1Auto Operation Does Not Operate — 1Removal and Installation — 1Preparation — 1Description — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1Service Information — 6Repair Information — 1Precaution — 1Preparation — 1Removal and Installation — 1Service Data — 1Preparation. Preparation — 1Component Parts — 1System — 1Ecu Diagnosis Information — 1Wiring Diagram. Door Mirror — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Removal and Installation — 1Exterior Lighting System :: Led Headlamp — 1System Description — 3Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance — 1Removal and Installation — 1System Description — 1System — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information. Bcm, Intelligent Key Unit — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis. Interior Lighting System Symptom — 1Removal and Installation — 1Service Data. Bulb Specifications — 1System Description — 1System — 1Ecu Diagnosis Information. Bcm, Ipdm E/r — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1System Description — 1Ecu Diagnosis Information. Bcm — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Preparation. Preparation — 1Removal and Installation. Horn — 1Preparation. Commercial Service Tools Or/and Repair Part — 1System Description — 1Component Parts — 1Ecu Diagnosis Information. Approaching Vehicle Sound for Pedestrians (vsp) Control Unit — 1Approaching Vehicle Sound for Pedestrians (vsp) — 1Vsp [approaching Vehicle Sound for Pedestrians (vsp) Control Unit] — 1Approaching Vehicle Sound for Pedestrians (vsp) System — 1Removal and Installation — 1Removal and Installation — 1Wireless Charger — 1System Description — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Removal and Installation — 1Component Parts — 1System — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information. Bcm — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Can Fundamental — 1Description — 1Trouble Diagnosis — 1Can (controller Area Network) — 1Description — 1
57steps
~342min
5/5difficulty
0204060801006548N·mlb·ft
Tightening torque found on this page
Done 0 of 57
  • Cplc
  • High Voltage Power Delivery Assembly
  • Charge Port
  • Charge Connector Lock Actuator
  • Immediate Charging Switch
  • Charging Status Indicator

Cplc Nissan Ariya

CPLC : Exploded View

CPLC CPLC bracket
:N·m(kg-m, in-lb)

CPLC : Removal & Installation

Remove instrument lower cover center .

Remove RH front kicking plate.Refer to Removal & Installation.

Remove RH dash side finisher. Refer to Removal & Installation.

Turn up the front right side of the floor carpet.

Remove front floor spacer RH. Refer to Exploded View.

Remove the CPLC installing nut and remove the CPLC harness connector .

Remove the CPLC bracket installing nut. (If necessary)

High Voltage Power Delivery Assembly Nissan Ariya

HIGH VOLTAGE POWER DELIVERY ASSEMBLY : Exploded View

EXPLODED VIEW

Harness bracket 1 Harness bracket 2 High voltage power delivery ASSY
Harness bracket 3 High voltage power delivery ASSY bracket (front RH) High voltage power delivery ASSY bracket (front LH)
High voltage harness (high voltage Junction box - traction motor inverter) Harness bracket 4 Harness bracket 5
Harness bracket 6 High voltage harness (high voltage Junction box - air conditioner unit) Terminal cover
High voltage harness protector lower bracket High voltage harness protector lower High voltage harness protector upper
High voltage power delivery ASSY bracket (rear LH) High voltage power delivery ASSY bracket (rear RH) Busbercover
Gasket Breather plug
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
: Always replace after every disassembly.
,, : Indicates that parts with the same mark are connected

HIGH VOLTAGE POWER DELIVERY ASSEMBLY : Removal & Installation

DANGER:

Since hybrid vehicles and electric vehicles contain a high voltage battery, there is the risk of electric shock, electric leakage, or similar accidents if the high voltage component and Nissan Ariya vehicle are handled incorrectly. Be sure to follow the correct work procedures when performing inspection and maintenance.

REMOVAL

  1. Check voltage in high voltage circuit. (Check that condenser are discharged.)

    DANGER:

    Touching high voltage components without using the appropriate protective equipment will cause electrocution.

  2. Drain coolant. Refer to COOLANT : Draining.

  3. Remove the ground bolt in the motor room.

    : Nissan Ariya Vehicle front

    DANGER:

    Touching high voltage components without using the appropriate protective equipment will cause electrocution.

  4. Remove the bus bar cover on the high voltage junction box.

    DANGER:

    Touching high voltage components without using the appropriate protective equipment will cause electrocution.

  5. Remove the bus bar cover fixing bolt to remove the terminal cover of the bus bar.

    DANGER:

    Touching high voltage components without using the appropriate protective equipment will cause electrocution.

  6. Remove the bus bar fastening bolt.

    DANGER:

    Touching high voltage components without using the appropriate protective equipment will cause electrocution.

  7. Remove the high voltage harness protector upper fixing bolt to remove the high voltage harness protector upper.

    DANGER:

    Touching high voltage components without using the appropriate protective equipment will cause electrocution.

  8. Remove the high voltage harness fixing bolt to remove the high voltage harness from the high voltage junction box.
    DANGER:

    Touching high voltage components without using the appropriate protective equipment will cause electrocution.

  9. Apply protective tape on the high voltage junction box opening area and high voltage harness.

    DANGER:

    Touching high voltage components without using the appropriate protective equipment will cause electrocution.

  10. Remove the harness bracket 6 fixing bolt.

    DANGER:

    Touching high voltage components without using the appropriate protective equipment will cause electrocution.

  11. Remove the high voltage harness connector, high voltage harness connector and the high voltage harness clip.

    DANGER:

    Touching high voltage components without using the appropriate protective equipment will cause electrocution.

    • High voltage harness connector is disconnected as per the following steps.

  12. Apply protective tape on the high voltage harness and the connector part.

    DANGER:

    Touching high voltage components without using the appropriate protective equipment will cause electrocution.

  13. Remove the harness protector lower fixing bolt to remove the high voltage harness protector lower.

    DANGER:

    Touching high voltage components without using the appropriate protective equipment will cause electrocution.

  14. Remove the harness clip.

    DANGER:

    Touching high voltage components without using the appropriate protective equipment will cause electrocution.

  15. Remove the high voltage harness bracket bolt.

    DANGER:

    Touching high voltage components without using the appropriate protective equipment will cause electrocution.

  16. Disconnect the high voltage harness connecter.

    DANGER:

    Touching high voltage components without using the appropriate protective equipment will cause electrocution.

    • High voltage harness connector is disconnected as per the following steps.

  17. Apply protective tape on the high voltage harness and connector part of the on-board charger.

    DANGER:

    Touching high voltage components without using the appropriate protective equipment will cause electrocution.

  18. Disconnect the harness connector.

    DANGER:

    Touching high voltage components without using the appropriate protective equipment will cause electrocution.

  19. Disconnect the harness connector.

    DANGER:

    Touching high voltage components without using the appropriate protective equipment will cause electrocution.

  20. Apply protective tape on the high voltage harness and the connector part.

    DANGER:

    Touching high voltage components without using the appropriate protective equipment will cause electrocution.

  21. Fasten the high voltage harness by lope in the area where is not disturb repairing operation.

    DANGER:

    Touching high voltage components without using the appropriate protective equipment will cause electrocution.

  22. Disconnect the harness connector and the harness connector.

    DANGER:

    Touching high voltage components without using the appropriate protective equipment will cause electrocution.

  23. Remove front side of the water hose from the on-board charger.

    DANGER:

    Touching high voltage components without using the appropriate protective equipment will cause electrocution.

  24. Remove rear side of the water hose from the DC/DC converter.

    DANGER:

    Touching high voltage components without using the appropriate protective equipment will cause electrocution.

  25. Remove high voltage power delivery ASSY fixing bolts and nuts to remove the high voltage power delivery ASSY from the Nissan Ariya vehicle.

    DANGER:

    Touching high voltage components without using the appropriate protective equipment will cause electrocution.

  26. Remove the high voltage power delivery ASSY bracket if needed.

    DANGER:

    Touching high voltage components without using the appropriate protective equipment will cause electrocution.

INSTALLATION

Note the followings, and install in the reverse order of removal.

  1. Connect high voltage harness connectors.

    DANGER:

    Touching high voltage components without using the appropriate protective equipment will cause electrocution.

    • High voltage harness connector is connected as per the following steps.

  2. Install the high voltage harness connector.

    DANGER:

    Touching high voltage components without using the appropriate protective equipment will cause electrocution.

    • High voltage harness connector is connected as per the following steps.

    • Be sure to check the harness connector is properly fitted after push the harness connector to the direction of the arrow.

      DANGER:

      Touching high voltage components without using the appropriate protective equipment will cause electrocution.

HIGH VOLTAGE POWER DELIVERY ASSEMBLY : Inspection

Electric Equipotential Test

  • Check the resistance between the high voltage junction box (Aluminum part) and the body (Ground bolt, )

  • Check the resistance between the on-board charger (Aluminum part) and the body (Ground bolt, )

  • Check the resistance between the DC/DC converter (Aluminum part) and the body (Ground bolt, )

    DANGER:

    Touching high voltage components without using the appropriate protective equipment will cause electrocution.

    :Nissan Ariya Vehicle front
    Standard : Less than 0.1Ω

    If result deviates from standard values, check that no paint, oil, dirt, or other substance is adhering to bolts or conductive mounting parts. If any such substance is adhering, clean the surrounding area and remove the substance.

Charge Port Nissan Ariya SUV

CHARGE PORT : Exploded View

REMOVAL

Charge port Bracket
: N·m (kg-m, in-lb)

DISASSEMBLY

Charge port Clip Pin
Spring (small) Lever Spring (large)
Damper Port cap 1 Port cap 2
Always replace after every disassembly.

CHARGE PORT : Removal & Installation

DANGER:

Since hybrid vehicles and electric vehicles contain a high voltage battery, there is the risk of electric shock, electric leakage, or similar accidents if the high voltage component and Nissan Ariya vehicle are handled incorrectly. Be sure to follow the correct work procedures when performing inspection and maintenance.

REMOVAL

  1. Check voltage in high voltage circuit. (Check that condenser are discharged.)

    DANGER:

    Touching high voltage components without using the appropriate protective equipment will cause electrocution.

  2. Discharge the refrigerant gas. Refer to Recycle Refrigerant.

  3. Remove the Li-ion battery undercover lid (Front RH) and the Li-ion battery undercover lid (Front LH).

  4. Lift up the Nissan Ariya vehicle and remove the front undercover rear, the Li-ion battery undercovers front (RH,LH) and the Li-ion battery under cover front. Refer to Exploded View.

    :Nissan Ariya Vehicle front

  5. Remove the reinforce fixing bolt and then remove the reinforce .

  6. Remove the quick charge port high voltage harness cramp.

    DANGER:

    Touching high voltage components without using the appropriate protective equipment will cause electrocution.

  7. Disconnect the quick charge port high voltage harness connector from the Li-ion battery.

    DANGER:
    • Touching high voltage components without using the appropriate protective equipment will cause electrocution.

    • Immediately insulate disconnected quick charge port high voltage harness connector and terminals with insulating tape, since there is the risk of electric shock.

  8. Remove the high voltage power delivery assembly. Refer to HIGH VOLTAGE POWER DELIVERY ASSEMBLY :Removal & Installation.

  9. Remove the A/C unit assembly. Refer to Removal & Installation.

  10. Remove the bracket.

    DANGER:

    Touching high voltage components without using the appropriate protective equipment will cause electrocution.

  11. Remove the charge port high voltage harness clip.

    DANGER:

    Touching high voltage components without using the appropriate protective equipment will cause electrocution.

  12. Remove the charge port lid. Refer to Removal & Installation.

  13. Remove the charge port mounting bolt.

    DANGER:

    Touching high voltage components without using the appropriate protective equipment will cause electrocution.

  14. Remove the charge port high voltage harness connector.

  15. Remove the charge port high voltage harness from the Nissan Ariya vehicle.

    DANGER:

    Touching high voltage components without using the appropriate protective equipment will cause electrocution.

INSTALLATION

Note the following and install in the reverse order of removal while be careful below point.

  1. Install the quick charge port high voltage harness connector.

    :Nissan Ariya Vehicle front

    DANGER:

    Touching high voltage components without using the appropriate protective equipment will cause electrocution.

    • Install the quick charge port high voltage harness as per the following steps.

  2. Install the reinforce .

    Reinforce fixing bolt :65 N·m

CHARGE PORT : Disassembly & Assembly

DISASSEMBLY

DANGER:

Since hybrid vehicles and electric vehicles contain a high voltage battery, there is the risk of electric shock, electric leakage, or similar accidents if the high voltage component and Nissan Ariya vehicle are handled incorrectly. Be sure to follow the correct work procedures when performing inspection and maintenance.

COMMON WORK

Remove the charge port lid. Refer to Removal & Installation.

Apply vinyl tape or equivalent (A) to protect the charge port.

Port Cap Side

Remove the clip that is attached to the pin.

Pull out pin of port cap.

Remove the spring and damper from port cap.

Lever Side

Remove the clip that is attached to the pin.

Pull out pin of lever.

ASSEMBLY

Note the following, and assemble in the reverse order of disassembly.

Port Cap and Lever

CHARGE PORT : Inspection

Inspection after install the quick charge port high voltage harness connector

Measure the length of point, and confirm the quick charge port high voltage harness connector length is standard value. Refer to Removal & Installation.

Standard value : less than 5 mm

DANGER:

Touching high voltage components without using the appropriate protective equipment will cause electrocution.

If the length is out of the standard value, reassemble the quick charge port high voltage harness connector according to the following procedure.

  1. Remove the quick charge port high voltage harness connector from the Li-ion battery. Refer to Removal & Installation.

  2. Remove the quick charge port high voltage harness connector from the slider with slide in the direction of the arrow 2 while the slider lock raised in the direction of the arrow 1.

  3. Set the gear with contact and of the quick charge port high voltage harness connector housing as the illustration.

  4. While keeping the status of step 3 and align the slider with the groove of the quick charge port high voltage harness connector housing as shown by point of the illustration and assemble.

  5. While keep pushing slider lock, slide in the direction arrow until locked slider lock as shown by illustration.

  6. Install the quick charge port high voltage harness connector to Li-ion battery. Refer to Removal & Installation.

Charge Connector Lock Actuator Nissan Ariya

CHARGE CONNECTOR LOCK ACTUATOR : Exploded View

Charge port Bracket Charge connector lock actuator

CHARGE CONNECTOR LOCK ACTUATOR : Removal & Installation

DANGER:

Since hybrid vehicles and electric vehicles contain a high voltage battery, there is the risk of electric shock, electric leakage, or similar accidents if the high voltage component and Nissan Ariya vehicle are handled incorrectly. Be sure to follow the correct work procedures when performing inspection and maintenance.

REMOVAL

Check voltage in high voltage circuit. (Check that condenser are discharged.)DANGER:

Touching high voltage components without using the appropriate protective equipment will cause electrocution.

Discharge the refrigerant gas. Refer to Recycle Refrigerant.

Remove the Li-ion battery undercover lid (front RH) and the Li-ion battery undercover lid (front LH).

Lift up the Nissan Ariya vehicle to remove the front undercover rear, the Li-ion battery undercovers front (RH, LH) and the Li-ion battery under cover front. Refer to Removal & Installation and Exploded View (66 kWh LI-ION BATTERY) or Exploded View (91kWh LI-ION BATTERY).

: Nissan Ariya Vehicle front

Remove the lack mounting fixing bolt to remove the lack mounting.

Remove the quick charge port high voltage harness cramp.

DANGER:

Touching high voltage components without using the appropriate protective equipment will cause electrocution.

Disconnect the quick charge port high voltage harness connector from the Li-ion battery.

DANGER:
  • Touching high voltage components without using the appropriate protective equipment will cause electrocution.

  • Immediately insulate disconnected quick charge port high voltage harness connector and terminals with insulating tape, since there is the risk of electric shock.

Remove the high voltage power delivery ASSY. Refer to HIGH VOLTAGE POWER DELIVERY ASSEMBLY : Removal & Installation.

Remove the A/C unit assembly. Refer to Removal & Installation.

Remove the bracket .DANGER:

Touching high voltage components without using the appropriate protective equipment will cause electrocution.

Remove the charge port high voltage harness clip .

DANGER:

Touching high voltage components without using the appropriate protective equipment will cause electrocution.

Remove the charge port lid. Refer to Removal & Installation.

Remove the charge port mounting bolt.DANGER:

Touching high voltage components without using the appropriate protective equipment will cause electrocution.

Remove the charge port high voltage harness connector.

Remove the charge port high voltage harness from the Nissan Ariya vehicle.DANGER:

Touching high voltage components without using the appropriate protective equipment will cause electrocution.

Remove the charge port high voltage harness from the charge connector lock actuator.DANGER:

Touching high voltage components without using the appropriate protective equipment will cause electrocution.

INSTALLATION

Note the following and install in the reverse order of removal while be careful below oint.

Install the quick charge port high voltage harness connector.DANGER:

Touching high voltage components without using the appropriate protective equipment will cause electrocution.

: Nissan Ariya Vehicle front

  • Install the quick charge port high voltage harness connector as per the following steps:

Install the lack mounting.

Lack mounting fixing bolt : 65 N·m

Quick charge port: Inspection

Inspection after install the quick charge port high voltage harness connector.

Measure the length of point , and confirm the quick charge port high voltage harness connector length is standard value. Refer to Removal & Installation (66 kWh LI-ION BATTERY) or Removal & Installation (91 kWh LI-ION BATTERY).DANGER:

Touching high voltage components without using the appropriate protective equipment will cause electrocution.

Standard value : less than 5 mm

If the length is out of the standard value, reassemble the quick charge port high voltage harness connector according to the following procedure.

  1. Remove the quick charge port high voltage harness connector from the Li-ion battery. Refer to Removal & Installation (66 kWh LI-ION BATTERY) or Removal & Installation (91 kWh LI-ION BATTERY).

  2. Remove the quick charge port high voltage harness connector from the slider with slide in the direction of the arrow 2 while the slider lock raised in the direction of the arrow 1.

  3. Set the gear with contact and of the quick charge port high voltage harness connector housing as the illustration.

  4. While keeping the status of step 3 and align the slider with the groove of the quick charge port high voltage harness connector housing as shown by point of the illustration and assemble.

  5. While keep pushing slider lock, slide in the direction arrow until locked slider lock as shown by illustration.

  6. Install the quick charge port high voltage harness connector to Li-ion battery. Refer to Removal & Installation (66 kWh LI-ION BATTERY) or Removal & Installation (91 kWh LI-ION BATTERY).

Immediate Charging Switch Nissan Ariya: FE0

IMMEDIATE CHARGING SWITCH : Removal & Installation

REMOVAL

Remove instrument lower panel LH. Refer to Exploded View.

Remove switch panel assembly from instrument lower panel LH.

Remove immediate charging switch from switch panel using a suitable tool (A).

INSTALLATION

Install in the reverse order of removal.

Charging Status Indicator Nissan Ariya 2026

CHARGING STATUS INDICATOR : Removal & Installation

REMOVAL

Remove instrument panel. Refer to Exploded View.

Remove switch panel assembly from instrument lower panel LH.

Release The charge status indicator bracket pawl in using a suitable tool (A) the direction of the arrow and remove the charge status indicator from the instrument panel.

INSTALLATION

Install in the reverse order of removal.