Dtc/circuit Diagnosis

In this manual: Dtc/circuit Diagnosis
How to Use This Manual — 1Precautions — 1Preparation — 1Vehicle Information — 1Basic Inspection — 1Preparation. Commercial Service Tools Or/and Repair Part — 1Description — 1Component Parts — 1System — 1Diagnosis System (vcm) — 1Ecu Diagnosis Information. Vcm — 1Ev Control System — 1Ev/hev (vcm) — 1Component Parts /circuit Diagnosis — 1Ev Control System — 1Periodic Maintenance. Ev System Warning Lamp — 1Removal and Installation. Vcm — 1Traction Motor System :: Front Traction Motor — 1Preparation — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Traction Motor System :: Rear Traction Motor — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Ev Battery System :: 66kwh Li-Ion Battery — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Disassembly and Assembly — 2Service Data — 1Ev Battery System :: 91kwh Li-Ion Battery — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Disassembly and Assembly — 1Service Data — 2Preparation. Vehicle Charging System — 1Vehicle Charging System :: Description — 1Component Parts — 2System — 1Diagnosis System (on-Board Charger) — 1Diagnosis System (dc/dc Converter) — 1Ecu Diagnosis Information — 1Vehicle Charging System — 1Charger/pd Module (on-Board Charger) — 1Cplc (cplc) — 1Dcdc (dc/dc Converter) — 1Component Parts/circuit Diagnosis — 1Symptom Diagnosis — 1Evse Inspection — 1Periodic Maintenance — 1Removal and Installation — 1Disassembly and Assembly — 1Preparation. High Voltage Cooling System — 1Description — 1Symptom Diagnosis. Overheating Cause Analysis — 1Periodic Maintenance — 1Coolant — 1Removal and Installation — 1Radiator — 1Service Data — 1Removal and Installation. Accelerator Control System — 1Reduction Gear: Re1f62a — 1Removal and Installation — 1Transaxle & Transmission :: Electric Shift — 1Description — 3Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Rear Final Drive: Rn1r62a — 1Removal and Installation — 1Preparation. Front Axle System — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data. Front Drive Shaft — 12wd — 14wd — 1Periodic Maintenance — 1Removal and Installation — 1Preparation. Front Suspension System — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Preparation. Road Wheels & Tires System — 1Description — 1System — 1Ecu Diagnosis Information. Bcm (body Control Module) — 1Tpms — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance. Road Wheels & Tires — 1Removal and Installation — 1Service Data — 1Preparation. Brake System — 1System Description — 1Component Parts — 1Ecu Diagnosis Information. Electrically-Driven Intelligent Brake Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Preparation. Parking Brake System — 1System Description — 1Component Parts — 1System — 1Ecu Diagnosis Information. Abs Actuator and Electric Unit (control Unit) — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Component Parts /circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Brake Control System :: With Vdc — 1System Description — 3Basic Inspection — 2Dtc/circuit Diagnosis — 1Symptom Diagnosis — 2Removal and Installation — 1Brake Control System :: Automatic Brake Hold — 1System Description — 3Component Parts /circuit Diagnosis — 1Removal and Installation — 1Brake Control System :: E-Step — 1System Description — 3Removal and Installation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Symptom Diagnosis — 1Rear Automatic Braking — 1System Description — 1Basic Inspection — 1Preparation. Steering System — 1System Description — 1Component Parts — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance. Steering Wheel — 1Removal and Installation — 1Service Data — 1System Description — 1Component Parts — 1Steering Control System — 1Ecu Diagnosis Information. Power Steering Control Module — 1Dtc/circuit Diagnosis — 1Component Parts /circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation. Power Steering Control Module — 1System Description — 1Removal and Installation — 1System Description — 1System — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Component Parts — 1Basic Inspection — 1Removal and Installation — 1System Description — 1System — 1Ecu Diagnosis Information. Air Bag Diagnosis Sensor Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1System Description. Description. Ventilation System — 1Removal and Installation — 1Preparation. Preparation — 1System Description — 1Basic Inspection — 1Symptom Diagnosis — 1Removal and Installation — 1Electric Compressor — 1Cooler Pipe and Hose — 1A/c Unit Assembly Cover — 1A/c Unit Assembly — 1Heater & Air Conditioning Control System :: Automatic Air Conditioning — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 2Dtc Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 2Preparation. Preparation — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1Preparation. Instrument Panel — 1Component Parts — 1System — 1Ecu Diagnosis Information. Flexible Center Storage Control Module — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Preparation. Preparation — 1Component Parts — 1System — 1Ecu Diagnosis Information. Driver Lumbar Support Control Module — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1System Description — 1System — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Manual Function Does Not Operate — 1Memory Function Does Not Operate — 1Removal and Installation — 1Preparation. Preparation — 1System Description — 1System (intelligent Key System) — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1U2141-87 Can Comm Circuit — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Automatic Back Door Operation Does Not Operate — 1Back Door Does Not Open — 1Door Does Not Lock/unlock with Door Lock and Unlock Switch — 1Removal and Installation — 1Hood — 1Radiator Core Support — 1Charge Port Lid — 1Front Fender — 1Front Door — 1Rear Door — 1Back Door — 1Hood Lock — 1Front Door Lock — 1Rear Door Lock — 1Back Door Lock — 1Outside Key Antenna — 1System Description — 1System — 1Ecu Diagnosis Information. Inverter (front), Inverter (rear), Bcm, Intelligent Key Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Preparation — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Front Passenger Side Power Window Does Not Operate — 1Rear Lh Side Power Window Does Not Operate — 1Rear Rh Side Power Window Does Not Operate — 1Removal and Installation. Power Window Main Switch — 1Preparation. Preparation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Sunroof Switch Assembly — 1Symptom Diagnosis — 1Auto Operation Does Not Operate — 1Removal and Installation — 1Preparation — 1Description — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1Service Information — 6Repair Information — 1Precaution — 1Preparation — 1Removal and Installation — 1Service Data — 1Preparation. Preparation — 1Component Parts — 1System — 1Ecu Diagnosis Information — 1Wiring Diagram. Door Mirror — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Removal and Installation — 1Exterior Lighting System :: Led Headlamp — 1System Description — 3Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance — 1Removal and Installation — 1System Description — 1System — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information. Bcm, Intelligent Key Unit — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis. Interior Lighting System Symptom — 1Removal and Installation — 1Service Data. Bulb Specifications — 1System Description — 1System — 1Ecu Diagnosis Information. Bcm, Ipdm E/r — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1System Description — 1Ecu Diagnosis Information. Bcm — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Preparation. Preparation — 1Removal and Installation. Horn — 1Preparation. Commercial Service Tools Or/and Repair Part — 1System Description — 1Component Parts — 1Ecu Diagnosis Information. Approaching Vehicle Sound for Pedestrians (vsp) Control Unit — 1Approaching Vehicle Sound for Pedestrians (vsp) — 1Vsp [approaching Vehicle Sound for Pedestrians (vsp) Control Unit] — 1Approaching Vehicle Sound for Pedestrians (vsp) System — 1Removal and Installation — 1Removal and Installation — 1Wireless Charger — 1System Description — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Removal and Installation — 1Component Parts — 1System — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information. Bcm — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Can Fundamental — 1Description — 1Trouble Diagnosis — 1Can (controller Area Network) — 1Description — 1
96steps
~576min
5/5difficulty
Done 0 of 96
  • P161d-61 Immobilizer. Motor Control
  • P161e-68 Immobilizer. Motor Control
  • P161f-64 Immobilizer. Motor Control
  • B2033-4a Dongle Ng
  • B2042-4a Electric Shift Authentication Fail
  • B2043-4a Electric Shift Id Discord
  • B2070-68 Key Registration
  • B2090-14 Nats Antenna Amp.
  • B2f70-01 Stop Lamp
  • B2f71-23 Stop Lamp
  • Stop Lamp Switch
  • Hood Switch
  • Horn Function

P161d-61 Immobilizer. Motor Control Nissan Ariya: FE0

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen itemsDTC detecting condition
P161D-61 IMMOBILIZER Diagnosis condition Power switch ON
Signal (terminal) —
Threshold When key registration has not been completed normally after replacing Intelligent Key unit.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Improper key registration operation

  • Power steering control module

  • Intelligent Key unit

FAIL-SAFE

Inhibit setting the vehicle to READY

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Power switch ON.

  2. Select “Self Diagnostic Result” mode of “MOTOR CONTROL” using CONSULT.

Is the DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P161D-61 is displayed with DTC B2033-4A, first perform the trouble diagnosis for DTC B2033- 4A.

Is DTC B2033–4A detected?

YES>>

Perform diagnosis of applicable. DTC B2033–4A: Refer to DTC Description.

NO>>

GO TO 2.

INTELLIGENT KEY REGISTRATION

  1. Perform registration of all Intelligent Keys using CONSULT.

    For registration procedures, refer to CONSULT immobilizer mode and follow the on-screen instructions.

  2. Erase DTC.

  3. Perform DTC confirmation procedure for DTC P161D-61.Refer to DTC Description.

Is DTC P161D-61 detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

REPLACE INTELLIGENT KEY UNIT

  1. Replace Intelligent Key unit. Refer to Removal and Installation.

  2. Erase DTC.

  3. Perform DTC confirmation procedure for DTC P161D-61. Refer to DTC Description.

  4. Check that the DTC is not detected.

>>

INSPECTION END

P161e-68 Immobilizer. Motor Control Nissan Ariya SUV

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen itemsDTC detecting condition
P161E-68 IMMOBILIZER Diagnosis condition Power switch ON
Signal (terminal) —
Threshold
  • When registration with Intelligent Key unit is not completed normally after replacement inverter (front).

  • When inverter (front) and Intelligent Key unit are replacement at the same time.

Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • When registration with Intelligent Key unit is not completed normally after replacement inverter (front).

  • Intelligent Key unit

  • Inverter (front)

When replacement any parts, replace one by one.

FAIL-SAFE

Inhibit setting the vehicle to READY

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Power switch ON.

  2. Select “Self Diagnostic Result” mode of “MOTOR CONTROL” using CONSULT.

Is the DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

PRECONDITIONING

Does bring the intelligent key inside the Nissan Ariya vehicle and turn on the power switch, when replaced the inverter (front)?

YES>>

GO TO 3.

NO>>

GO TO 2.

INVERTER REGISTRATION

Bring the intelligent key inside the Nissan Ariya vehicle and turn on the power switch.

Is the DTC detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

REPLACE INTELLIGENT KEY UNIT

Replace Intelligent Key unit. Refer to Removal and Installation.

Is the DTC detected?

YES>>

GO TO 4.

NO>>

INSPECTION END

REPLACE INVERTER (FRONT)

Replace inverter (front). Refer to INVERTER (FRONT) : Removal & Installation.

>>

INSPECTION END

P161f-64 Immobilizer. Motor Control Nissan Ariya first Gen

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen itemsDTC detecting condition
P161F-64 IMMOBILIZER Diagnosis condition Power switch ON
Signal (terminal) —
Threshold When inverter (front) detects an immobilizer malfunction and READY set is prohibited.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Inverter (front)

FAIL-SAFE

Inhibit setting the vehicle to READY

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Power switch ON.

  2. Select “Self Diagnostic Result” mode of “MOTOR CONTROL” using CONSULT.

Is the DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

REPLACE INVERTER (FRONT)

Replace inverter (front).Refer to INVERTER (FRONT) : Removal & Installation.

>>

INSPECTION END

B2033-4a Dongle Ng Nissan Ariya first Gen

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen itemsDTC detection condition
B2033–4A Dongle not good Diagnosis condition Power switch ON
Signal (terminal) CAN communication signal
Threshold The ID verification results NG
Diagnosis delay time 1 second or more

POSSIBLE CAUSE

  • Harness or connector

    (CAN communication line is open or shorted)

  • Intelligent Key unit

  • Power steering control module

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Power switch ON.

  2. Select “Self Diagnostic Result” mode of “INTELLIGENT KEY” using CONSULT.

Is the DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

PERFORM INITIALIZATION

  1. Perform initialization of Intelligent Key unit and registration of all Intelligent Keys using CONSULT.

    For initialization and registration procedures, refer to CONSULT immobilizer mode and follow the on-screen instructions.

  2. Check that the Nissan Ariya vehicle can be set to READY using registered Intelligent Key.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

GO TO 2.

REPLACE INTELLIGENT KEY UNIT

Replace Intelligent Key unit. Refer to Removal and Installation.

Is the DTC detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

REPLACE POWER STEERING CONTROL MODULE

Replace power steering control module. Refer to EPS CONTROL UNIT : Removal & Installation.

>>

INSPECTION END

B2042-4a Electric Shift Authentication Fail Nissan Ariya: FE0

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen itemsDTC detecting condition
B2042–4A Electric shift authentication fail Diagnosis condition When power switch is turned from OFF to ON
Signal (terminal) CAN communication signal
Threshold When Intelligent Key unit cannot detect CAN communication with electric shift control module
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Harness or connectors

    (CAN communication line is open or shorted)

  • Electric shift control module

FAIL-SAFE

Prohibit shifting the shift selector from P position

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Power switch ON.

  2. Check DTC in “Self Diagnostic Result” mode of “INTELLIGENT KEY” using CONSULT.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY OF INTELLIGENT KEY UNIT

  1. Select “Self Diagnostic Result” mode of “INTELLIGENT KEY” using CONSULT.

  2. If DTC B2042–4A is displayed with two or more DTCs are detected, refer to DTC inspection priority chart, and determine trouble diagnosis.

Is applicable DTC detected?

YES>>

Perform the trouble diagnosis related to the detected DTC. Refer to DTC Index.

NO>>

GO TO 2.

CHECK DTC PRIORITY OF ELECTRIC SHIFT CONTROL MODULE

Select “Self Diagnostic Result” mode of “SHIFT” using CONSULT.

Is the DTC detected?

YES>>

Perform the trouble diagnosis related to the detected DTC. Refer to DTC Index.

NO>>

Replace electric shift control module. Refer to ELECTRIC SHIFT CONTROL MODULE : Removal & Installation.

B2043-4a Electric Shift Id Discord Nissan Ariya 1st generation

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen itemsDTC detecting condition
B2043–4A Electric shift ID discord Diagnosis condition When registering electric shift control module
Signal (terminal) CAN communication signal
Threshold Electric shift control module registration has not been completed normally
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Improper electric shift control module registration operation

FAIL-SAFE

Prohibit shifting the shift selector from P position

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Power switch ON.

  2. Check DTC in “Self Diagnostic Result” mode of “INTELLIGENT KEY” using CONSULT.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

REPLACE ELECTRIC SHIFT CONTROL MODULE

Replace electric shift control module. Refer to ELECTRIC SHIFT CONTROL MODULE : Removal & Installation.

>>

INSPECTION END

B2070-68 Key Registration Nissan Ariya first Gen

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen itemsDTC detecting condition
B2070–68 Key registration Diagnosis condition —
Signal (terminal) —
Threshold Intelligent Key that does not match the Nissan Ariya vehicle is registered.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Improper registration operation

  • Intelligent Key

  • Intelligent Key unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Perform initialization of Intelligent Key unit and registration of all Intelligent Keys using CONSULT.

  2. Select “Self Diagnostic Result” mode of “INTELLIGENT KEY” using CONSULT.

Is the DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

REPLACE INTELLIGENT KEY

  1. Replace Intelligent Key that matches the Nissan Ariya vehicle.

  2. Perform initialization of Intelligent Key unit and registration of Intelligent Key using CONSULT.

    For initialization and registration procedures, refer to CONSULT immobilizer mode and follow the on-screen instructions.

  3. Erase DTC.

  4. Perform DTC confirmation procedure for B2070–68. Refer to DTC Description.

Is the DTC detected?

YES>>

GO TO 2.

NO>>

INSPECTION END

REPLACE INTELLIGENT KEY UNIT

Replace Intelligent Key unit.Refer to Removal and Installation.

>>

INSPECTION END

B2090-14 Nats Antenna Amp. Nissan Ariya SUV

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen itemsDTC detecting condition
B2090–14 NATS antenna amplifier Diagnosis condition Power switch ON
Signal (terminal) NATS antenna amp. signal
Threshold Inactive communication between NATS antenna amp. and Intelligent Key unit
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Harness or connectors

    (NATS antenna amp. circuit is open or shorted.)

  • Power switch (NATS antenna amp.)

  • Intelligent Key unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Power switch ON.

  2. Select “Self Diagnostic Result” mode of “INTELLIGENT KEY” using CONSULT.

Is the DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK NATS ANTENNA AMP. COMMUNICATION SIGNAL

Check signal between power switch harness connector and ground using an oscilloscope.
(+)(–)Condition

Signal

(Reference value)
Power switch
ConnectorTerminal
M143 2 Ground Intelligent Key battery is removed When a registered Intelligent Key backside is contacted to power switch 0 V
Other than above
3 When a registered Intelligent Key backside is contacted to power switch 0 V
Other than above

Is the inspection result normal?

YES>>

Replace power switch. Refer to Removal and Installation.

NO>>

GO TO 2.

CHECK NATS ANTENNA AMP. COMMUNICATION SIGNAL CIRCUIT

  1. Power switch OFF.

  2. Disconnect Intelligent Key unit connector and power switch connector.

  3. Check continuity between power switch harness connector and Intelligent Key unit harness connector.

    Power switchIntelligent Key unitContinuity
    ConnectorTerminalConnectorTerminal
    M143 2 M79 19 Existed
    3 20
  4. Check continuity between power switch harness connector and ground.

    Power switch—Continuity
    ConnectorTerminal
    M143 2 Ground Not existed
    3

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace harness.

REPLACE INTELLIGENT KEY UNIT

Replace Intelligent Key unit. Refer to Removal and Installation.

>>

INSPECTION END

B2f70-01 Stop Lamp Nissan Ariya first Gen

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen itemsDTC detecting condition
B2F70-01 Stop lamp Diagnosis condition When brake pedal is depressed
Signal (terminal)
  • Stop lamp switch 1 signal

  • Stop lamp switch 2 signal

Threshold BCM makes a comparison between stop lamp switch 1 signal and stop lamp switch 2 signal. It judges from their values to detect the malfunctioning circuit 10 consecutive times
Diagnosis delay time Depress brake pedal 10 times

POSSIBLE CAUSE

  • Harness or connectors

    (Stop lamp switch circuit is open or shorted)

  • Stop lamp switch

  • Fuse

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Depress brake pedal 10 times.

  2. Power switch ON.

  3. Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK STOP LAMP SWITCH

  1. Select “Brake switch 1” and “Brake switch 2” in “Data Monitor” mode of “SIGNAL BUFFER” of “BCM” using CONSULT.

  2. Check “Brake switch 1” and “Brake switch 2” indication under the following condition.

    Monitor itemConditionIndication
    Brake switch 1 Brake pedal Depressed OFF
    Not depressed ON
    Brake switch 2 Depressed ON
    Not depressed OFF

Is the indication normal?

YES>>

INSPECTION END

NO-1>>

Brake switch 1: GO TO 2.

NO-2>>

Brake switch 2: GO TO 7.

CHECK FUSE

  1. Power switch OFF.

  2. Check that the following fuse is not blown (open).

    Signal nameFuse No.
    Ignition power supply 39 (5 A)

Is the fuse blown (open)?

YES>>

Replace the blown (open) fuse after replacing the cause of blown (open).

NO >>

GO TO 3.

CHECK STOP LAMP SWITCH SIGNAL-1

  1. Disconnect BCM connector.

  2. Power switch ON.

  3. Check voltage between BCM harness connector and ground.

    (+)(–)ConditionVoltage
    BCM
    ConnectorTerminal
    M9 111 Ground Stop lamp switch ON (brake pedal is not depressed) 9 – 16 V
    Stop lamp switch OFF (brake pedal is depressed) 0 V

Is the inspection normal?

YES>>

INSPECTION END

NO>>

GO TO 4.

CHECK STOP LAMP SWITCH POWER SUPPLY CIRCUIT-1

  1. Power switch OFF.

  2. Disconnect stop lamp switch connector.

  3. Power switch ON.

  4. Check voltage between stop lamp switch harness connector and ground.

    (+)(–)Voltage
    Stop lamp switch
    ConnectorTerminal
    E115 4 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Check harness for open or short between stop lamp switch and fuse.

CHECK STOP LAMP SWITCH SIGNAL CIRCUIT-1

  1. Power switch OFF.

  2. Check continuity between stop lamp switch harness connector and BCM harness connector.

    Stop lamp switchBCMContinuity
    ConnectorTerminalConnectorTerminal
    E115 3 M9 111 Existed
  3. Check continuity between stop lamp switch harness connector and ground.

    Stop lamp switch—Continuity
    ConnectorTerminal
    E115 3 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace harness.

CHECK STOP LAMP SWITCH

Refer to Component Inspection.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace stop lamp switch. Refer to BRAKE PEDAL : Exploded View.

CHECK FUSE

  1. Power switch OFF.

  2. Check that the following fuse is not blown (open).

    Signal nameFuse No.
    Battery power supply 13 (10 A)

Is the fuse blown (open)?

YES>>

Replace the blown (open) fuse after replacing the cause of blown (open).

NO >>

GO TO 8.

CHECK STOP LAMP SWITCH SIGNAL-2

  1. Disconnect BCM connector.

  2. Check voltage between BCM harness connector and ground.

    (+)(–)ConditionVoltage
    BCM
    ConnectorTerminal
    M9 110 Ground Stop lamp switch ON (brake pedal is depressed) 9 – 16 V
    Stop lamp switch OFF (brake pedal is not depressed) 0 V

Is the inspection normal?

YES>>

INSPECTION END

NO>>

GO TO 9.

CHECK STOP LAMP SWITCH POWER SUPPLY CIRCUIT-2

  1. Disconnect stop lamp switch connector.

  2. Check voltage between stop lamp switch harness connector and ground.

    (+)(–)Voltage
    Stop lamp switch
    ConnectorTerminal
    E115 1 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Check harness for open or short between stop lamp switch and fuse.

CHECK STOP LAMP SWITCH SIGNAL CIRCUIT-2

  1. Check continuity between stop lamp switch harness connector and BCM harness connector.

    Stop lamp switchBCMContinuity
    ConnectorTerminalConnectorTerminal
    E115 2 M9 110 Existed
  2. Check continuity between stop lamp switch harness connector and ground.

    Stop lamp switch—Continuity
    ConnectorTerminal
    E115 2 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace harness.

B2f71-23 Stop Lamp Nissan Ariya first Gen

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen itemsDTC detecting condition
B2F71-23 Stop lamp Diagnosis condition Power switch ON
Signal (terminal) Stop lamp switch 1 signal
Threshold When stop lamp switch 1 signal is input even though the brake pedal is not depressed
Diagnosis delay time 10 hours or more

POSSIBLE CAUSE

  • Harness or connectors

    (Stop lamp switch circuit is short to battery)

  • Stop lamp switch

  • Fuse

  • BCM

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Not depress brake pedal and wait for 10 hours or more.

  2. Power switch ON.

  3. Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK FUSE

  1. Power switch OFF.

  2. Check that the following fuse is not blown (open).

    Signal nameFuse No.
    Ignition power supply 39 (5 A)

Is the fuse blown (open)?

YES>>

Replace the blown (open) fuse after replacing the cause of blown (open).

NO >>

GO TO 2.

CHECK STOP LAMP SWITCH SIGNAL

  1. Disconnect BCM connector.

  2. Power switch ON.

  3. Check voltage between BCM harness connector and ground.

    (+)(–)ConditionVoltage
    BCM
    ConnectorTerminal
    M9 111 Ground Stop lamp switch ON (brake pedal is not depressed) 9 – 16 V
    Stop lamp switch OFF (brake pedal is depressed) 0 V

Is the inspection normal?

YES>>

Replace BCM. Refer to Removal and Installation.

NO>>

GO TO 3.

CHECK STOP LAMP SWITCH POWER SUPPLY CIRCUIT

  1. Power switch OFF.

  2. Disconnect stop lamp switch connector.

  3. Power switch ON.

  4. Check voltage between stop lamp switch harness connector and ground.

    (+)(–)Voltage
    Stop lamp switch
    ConnectorTerminal
    E115 4 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Check harness for open or short between stop lamp switch and fuse.

CHECK STOP LAMP SWITCH SIGNAL CIRCUIT

  1. Power switch OFF.

  2. Check continuity between stop lamp switch harness connector and BCM harness connector.

    Stop lamp switchBCMContinuity
    ConnectorTerminalConnectorTerminal
    E115 3 M9 111 Existed
  3. Check continuity between stop lamp switch harness connector and ground.

    Stop lamp switch—Continuity
    ConnectorTerminal
    E115 3 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace harness.

CHECK STOP LAMP SWITCH

Refer to Component Inspection.

Is the inspection result normal?

YES>>

Replace BCM. Refer to Removal and Installation.

NO>>

Replace stop lamp switch. Refer to BRAKE PEDAL : Exploded View.

Stop Lamp Switch Nissan Ariya SUV

Component Inspection

CHECK STOP LAMP SWITCH

  1. Power switch OFF.

  2. Disconnect stop lamp switch connector.

  3. Check continuity between stop lamp switch terminals.

    Stop lamp switchConditionContinuity
    Terminal
    1 2 Brake pedal Not depressed Not existed
    Depressed Existed
    3 4 Not depressed Existed
    Depressed Not existed

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace stop lamp switch. Refer to BRAKE PEDAL : Exploded View.

Hood Switch Nissan Ariya 1st generation

Component Function Check

CHECK FUNCTION

  1. Select “Hood switch” in “DATA MONITOR” mode of “IPDM E/R” using CONSULT.

  2. Check “Hood switch” indication under the following condition.

    Monitor itemConditionIndication
    Hood switch Hood Open Open
    Close Close

Is the indication normal?

YES>>

Hood switch is OK.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK HOOD SWITCH SIGNAL

  1. Power switch OFF.

  2. Disconnect hood switch connector.

  3. Check voltage between hood switch harness connector and ground.

    (+)(–)Condition

    Voltage

    (Approx.)
    Hood switch
    ConnectorTerminal
    E84 2 Ground Open the hood 6 – 16 V

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

GO TO 2.

CHECK HOOD SWITCH SIGNAL CIRCUIT

  1. Disconnect IPDM E/R connector.

  2. Check continuity between IPDM E/R harness connector and hood switch harness connector.

    IPDM E/RHood switchContinuity
    ConnectorTerminalConnectorTerminal
    E42 52 E84 2 Existed
  3. Check continuity between IPDM E/R harness connector and ground.

    IPDM E/R—Continuity
    ConnectorTerminal
    E42 52 Ground Not existed

Is the inspection result normal?

YES>>

Replace IPDM E/R. Refer to Removal and Installation.

NO>>

Repair or replace harness.

CHECK HOOD SWITCH GROUND CIRCUIT

Check continuity between hood switch harness connector and ground.

Hood switch—Continuity
ConnectorTerminal
E84 1 Ground Existed

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace harness.

CHECK HOOD SWITCH

Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Replace hood lock assembly. Refer to Removal & Installation.

CHECK INTERMITTENT INCIDENT

Refer to Intermittent Incident.

>>

INSPECTION END

Component Inspection

CHECK HOOD SWITCH

  1. Power switch OFF.

  2. Disconnect hood switch connector.

  3. Check continuity between hood switch terminals.

    Hood switchConditionContinuity
    Terminal
    1 2 Hood Open Existed
    Close Not existed

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace hood lock assembly. Refer to Removal & Installation.

Horn Function Nissan Ariya first Gen

Component Function Check

CHECK FUNCTION

  1. Power switch OFF.

  2. Perform “HORN” in “ACTIVE TEST” mode of “IPDM E/R” using CONSULT.

  3. Check the horn operation.

    Test itemDescription
    HORN On Horn low/high Sounds (for 0.5 sec.)

Is the operation normal?

YES>>

INSPECTION END

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK HORN FUNCTION

Check horn function with horn switch.

Do horns sound?

YES>>

GO TO 2.

NO>>

Perform the trouble diagnosis for horn circuit. Refer to Wiring Diagram.

CHECK IPDM E/R POWER SUPPLY CIRCUIT

  1. Power switch OFF.

  2. Disconnect horn relay connector and IPDM E/R connector.

  3. Check continuity between IPDM E/R harness connector and horn relay harness connector.

    IPDM E/RHorn relayContinuity
    ConnectorTerminalConnectorTerminal
    E37 9 E77 2 Existed
  4. Check continuity between IPDM E/R harness connector and ground.

    IPDM E/R—Continuity
    ConnectorTerminal
    E37 9 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace harness.

CHECK INTERMITTENT INCIDENT

Refer to Intermittent Incident.

>>

INSPECTION END