Dtc/circuit Diagnosis
- C1040-63 Emergency Brake System
- C1041-55 Control Unit
- C1042-04 Cut Valve 1
- C1051-04 Pump Motor
- C1055-49 Can Comm Circuit
- C1056-13 Battery Power Supply
- C1058-01 Control Unit
- C105d-7b Brake Fluid Level Switch
- C105e-92 Pressure Sensor
- C105e-93 Pressure Sensor
- C105f-85 Control Unit
- C105f-92 Control Unit
- C1061-02 Wheel Sensor
- C1061-07 Wheel Sensor
- C1061-09 Wheel Sensor
- C1061-11 Wheel Sensor
- C1061-12 Wheel Sensor
- C1061-13 Wheel Sensor
- C1061-1c Wheel Sensor
- C1061-38 Wheel Sensor
- C1061-4a Wheel Sensor
- C1061-64 Wheel Sensor
- C1061-92 Wheel Sensor
- C1063-02 Wheel Sensor
- C1063-07 Wheel Sensor
- C1063-09 Wheel Sensor
- C1063-11 Wheel Sensor
- C1063-12 Wheel Sensor
- C1063-13 Wheel Sensor
- C1063-1c Wheel Sensor
- C1063-38 Wheel Sensor
- C1063-4a Wheel Sensor
- C1063-64 Wheel Sensor
- C1063-92 Wheel Sensor
- C1065-02 Wheel Sensor
- C1065-07 Wheel Sensor
- C1065-09 Wheel Sensor
- C1065-11 Wheel Sensor
- C1065-12 Wheel Sensor
- C1065-13 Wheel Sensor
- C1065-1c Wheel Sensor
- C1065-38 Wheel Sensor
- C1065-4a Wheel Sensor
- C1065-64 Wheel Sensor
- C1065-92 Wheel Sensor
- C1067-02 Wheel Sensor
- C1067-07 Wheel Sensor
- C1067-09 Wheel Sensor
- C1067-11 Wheel Sensor
- C1067-12 Wheel Sensor
- C1067-13 Wheel Sensor
- C1067-1c Wheel Sensor
- C1067-38 Wheel Sensor
- C1067-4a Wheel Sensor
- C1067-64 Wheel Sensor
- C1067-92 Wheel Sensor
- C1068-95 Wheel Sensor
- C1068-96 Wheel Sensor
- C1069-95 Wheel Sensor
- C106a-04 Wheel Sensor
- C106a-55 Wheel Sensor
- C106a-62 Wheel Sensor
- C106a-64 Wheel Sensor
- C106a-95 Wheel Sensor
- C106b-64 Stop Lamp Switch
- C106c-01 Pressure Sensor
- C106c-02 Pressure Sensor
- C106c-16 Pressure Sensor
- C106c-17 Pressure Sensor
- C106c-64 Pressure Sensor
- C106e-54 Steering Angle Sensor
- C106e-55 Steering Angle Sensor
- C106e-64 Steering Angle Sensor
- C106f-54 Steering Angle Sensor
- C1070-01 Side G Sensor
- C1070-54 Side G Sensor
- C1070-64 Side G Sensor
- C1071-54 Decel G Sensor
- C1071-61 Decel G Sensor
- C1071-64 Decel G Sensor
- C1072-01 Yaw Rate Sensor
- C1072-64 Yaw Rate Sensor
- C1072-83 Yaw Rate Sensor
- C1076-55 Control Unit
- C1077-55 Control Unit
- C1077-92 Control Unit
- C1078-55 Control Unit
- C1079-55 Control Unit
- C107a-55 Control Unit
- C107b-53 Vdc Function
- C107c-53 Control Unit
- C1080-86 Vcm System
- C1082-86 Vcm System
- C1083-86 Steering Angle Sensor System
- C1085-86 Combination Meter System
- C1086-86 Bcm System
- C1087-86 Ipdm E/r System
- C1088-86 Av System
- C1090-86 Adas Control Unit System
- C1092-86 4wd/awd System
- C1094-86 Vcm System
- C1095-86 Vcm System
- C1096-86 Chassis Control System
- C1098-86 Avm System
- C10aa-63 Pump Motor
- C10ac-54 G Sensor
- C10ad-04 Brake Backup Function
- C10af-01 Pressure Sensor
- C10b0-01 Parking Brake Actuator (rh)
- C10b0-09 Parking Brake Actuator (rh)
- C10b1-01 Parking Brake Actuator (lh)
- C10b1-09 Parking Brake Actuator (lh)
- C10b2-01 Parking Brake Switch
- C10b2-64 Parking Brake Switch
- C10b3-44 Parking Brake Contrtol Module
- C10b3-49 Parking Brake Contrtol Module
- C10b3-53 Parking Brake Contrtol Module
- C10b3-55 Parking Brake Contrtol Module
- C10b3-68 Parking Brake Control Module
- C10b4-98 Parking Brake Over Heart
- C10b5-76 Parking Brake Assembly Check
- C10b6-68 Parking Brake System
- C10b7-16 Parking Brake Power Supply
- C10b7-17 Parking Brake Power Supply
- C10b8-77 Parking Brake System
- C10b9-77 Parking Brake System
- U0073-00 Can Comm Circuit
- U0073-88 Can Communication
- U0076-00 Can Comm Circuit
- U0076-88 Can Comm Circuit
- U2112-87 Can Comm Circuit
- U2140-87 Can Comm Circuit
- U2143-87 Can Comm Err
- U214e-87 Can Comm Err
- U214f-87 Can Comm Err
- U2152-87 Can Comm Circuit
- U2154-87 Can Comm Circuit
- U2156-87 Can Comm Circuit
- U215b-87 Can Comm Circuit
- U2212-87 Can Comm Circuit
- U2240-87 Can Comm Circuit
- U2241-87 Can Comm Circuit
- U2243-87 Can Comm Err
- U224e-87 Can Comm Circuit
- U2252-87 Can Comm Circuit
- U225b-87 Can Comm Circuit
- U2275-87 Can Comm Circuit
- U2276-87 Can Comm Circuit
- Power Supply and Ground Circuit [abs Actuator and Electric Unit (control Unit)]
- Brake Fluid Level Switch
- Abs Warning Lamp
- Brake Warning Lamp
- Vdc Off Indicator Lamp
- Vdc Warning Lamp
C1040-63 Emergency Brake System Nissan Ariya 1st generation
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1040 | 63 | Emergency brake | Diagnosis condition |
|
|
| Signal (terminal) | CAN communication signal | ||||
| Threshold | When a malfunction is detected in ADAS control unit 2 system. | ||||
| Diagnosis delay time | 2 seconds or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
Normal control
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2.
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1040-63" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK ADAS CONTROL UNIT 2 SYSTEM
With CONSULT
Perform self-diagnosis for “ICC/ADAS 2”.
Is DTC detected?
YES>>Check the DTC. Refer to DTC Index.
NO>>GO TO 2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
CHECK CONNECTOR AND TERMINAL
Disconnect 12V battery negative terminal.
Disconnect ADAS control unit 2 harness connector.
Check the ADAS control unit 2 harness connector for disconnection or looseness.
Check the ADAS control unit 2 terminals for damage or loose connection with harness connector.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 4.
NO>>Repair / replace harness, connector, or terminal, securely lock the connector. GO TO 4.
PERFORM SELF-DIAGNOSIS
With CONSULT
Connect ADAS control unit 2 harness connector.
Connect ABS actuator and electric unit (control unit) harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC detected?
YES>>Check the DTC. Refer to DTC Index.
NO>>INSPECTION END
C1041-55 Control Unit Nissan Ariya 2026
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1041 | 55 | Configuration | Diagnosis condition |
|
|
| Signal (terminal) | — | ||||
| Threshold | When not programing is not complete. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
| Programing is not complete | Programing is not complete |
FAIL-SAFE
Normal control
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2.
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1041-55" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
PERFORM PROGRAMING
Perform programming of ABS actuator and electric unit (control unit). Refer to Work Procedure.
>>GO TO 2.
PERFORM SELF-DIAGNOSIS
With CONSULT
Replace the ABS actuator and electric unit (control unit) even if other DTCs are displayed along with “C1041-55” in self-diagnosis for “ABS”.
>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
C1042-04 Cut Valve 1 Nissan Ariya
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1042 | 04 | Cut valve 1 | Diagnosis condition |
|
|
| Signal (terminal) | — | ||||
| Threshold | When a malfunction is detected in cut valve 1. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2.
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1042-04" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 2.
PERFORM SELF-DIAGNOSIS
With CONSULT
Connect 12V battery negative terminal.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1042-04” detected?
YES>>GO TO 3.
NO>>INSPECTION END
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
C1051-04 Pump Motor Nissan Ariya 2023
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1051 | 04 | Pump motor | Diagnosis condition |
|
|
| Signal (terminal) | — | ||||
| Threshold | When a malfunction is detected in motor or motor relay. | ||||
| Diagnosis delay time | 19 seconds or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2.
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1051-04" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 2.
PERFORM SELF-DIAGNOSIS
With CONSULT
Connect 12V battery negative terminal.
Power switch OFF to ON, and wait 30 seconds.
Drive the Nissan Ariya vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1051-04” detected?
YES>>GO TO 3.
NO>>INSPECTION END
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 4.
ERASE SELF-DIAGNOSIS RESULT (1)
With CONSULT
Drive the Nissan Ariya vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
INSPECTION END
CHECK TERMINAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>Repair / replace harness or connector. GO TO 6.
ERASE SELF-DIAGNOSIS RESULT (2)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect 12V battery negative terminal.
Drive the Nissan Ariya vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
INSPECTION END
C1055-49 Can Comm Circuit Nissan Ariya first Gen
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | ||||
|---|---|---|---|---|---|---|
| C1055 | 49 | CAN system | 1 | Diagnosis condition |
|
|
| Signal (terminal) | CAN communication signal | |||||
| Threshold | When CAN communication signal is not continuously transmitted from ABS actuator and electric unit (control unit). | |||||
| Diagnosis delay time | 2 seconds or more | |||||
| 2 | Diagnosis condition |
|
||||
| Signal (terminal) | CAN communication signal | |||||
| Threshold | When CAN communication signal is not continuously received from ABS actuator and electric unit (control unit). | |||||
| Diagnosis delay time | 2 seconds or more | |||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
CAN communication line |
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2.
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1055-49" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
Refer to Trouble Diagnosis Flow Chart.
C1056-13 Battery Power Supply Nissan Ariya first Gen
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1056 | 13 | Battery power supply | Diagnosis condition |
|
|
| Signal (terminal) | Power switch ON power supply | ||||
| Threshold | When power switch ON power supply voltage is 10 V or less. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
Normal control
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2.
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1056-13" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: Check the 12V battery (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK 12V BATTERY
Check the 12V battery. Refer to Work Procedure.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace error-detected parts.
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness or connector, securely lock the connector.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 4.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
CHECK VCM SYSTEM
With CONSULT
Perform self-diagnosis for “EV/HEV”.
Is DTC detected?
YES>>Check the DTC. Refer to DTC Index.
NO>>GO TO 5.
PERFORM SELF-DIAGNOSIS
With CONSULT
Connect 12V battery negative terminal.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC "C1056-13" detected?
YES-1>>“CRNT” is displayed: Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
YES-2>>“PAST” is displayed: Check the 12V battery. Refer to Work Procedure.
NO>>INSPECTION END
C1058-01 Control Unit Nissan Ariya: FE0
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1058 | 01 | Control unit | Diagnosis condition |
|
|
| Signal (terminal) | — | ||||
| Threshold | When there is an internal malfunction in the ABS actuator and electric unit (control unit). | ||||
| Diagnosis delay time | 2 seconds or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2.
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1058-01" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
ADJUST THE NEUTRAL POSITION OF STEERING ANGLE SENSOR
Perform neutral position adjustment of steering angle sensor. Refer to Work Procedure.
Perform “All DTC Reading”.
Is DTC detected?
YES>>Check the DTC.
NO>>GO TO 2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
PERFORM SELF-DIAGNOSIS
With CONSULT
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC "C1058-01" detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END [Although motor built in the ABS actuator and electric unit (control unit) operates temporarily without a break, this is not a malfunction. Erase the all memory of self-diagnosis results.]
C105d-7b Brake Fluid Level Switch Nissan Ariya: FE0
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | ||||
|---|---|---|---|---|---|---|
| C105D | 7B | Brake fluid level low | 1 | Diagnosis condition |
|
|
| Signal (terminal) | Brake fluid level switch signal | |||||
| Threshold | When brake fluid level low signal is detected. | |||||
| Diagnosis delay time | 5 seconds or more | |||||
| 2 | Diagnosis condition |
|
||||
| Signal (terminal) | Brake fluid level switch signal | |||||
| Threshold | When an open circuit is detected in brake fluid level switch circuit. | |||||
| Diagnosis delay time | 5 seconds or more | |||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2.
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than food assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C105D-7B" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK BRAKE FLUID LEVEL
Power switch OFF.
Check the brake fluid level. Refer to BRAKE FLUID : Inspection.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Refill brake fluid. Refer to BRAKE FLUID : Refilling. GO TO 2.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC "C105D-7B" detected?
YES>>GO TO 3.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the brake fluid level switch harness connector for disconnection or looseness.
Check the combination meter harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Repair / replace harness or connector. GO TO 4.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Connect 12V battery negative terminal.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C105D-7B” detected?
YES>>GO TO 5.
NO>>INSPECTION END
CHECK BRAKE FLUID LEVEL SWITCH
Check the brake fluids level switch. Refer to Component Inspection.
Is the inspection result normal?
YES>>GO TO 7.
NO>>Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation. GO TO 6.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C105D-7B” detected?
YES>>GO TO 7.
NO>>INSPECTION END
CHECK CONNECTOR AND TERMINAL
Disconnect 12V battery negative terminal.
Disconnect brake fluid level switch harness connector.
Check the brake fluid level switch harness connector for disconnection or looseness.
Check the brake fluid level switch terminals for damage or loose connection with harness connector.
Disconnect combination meter harness connector.
Check the combination meter harness connector for disconnection or looseness.
Check the combination mete terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 4.
NO>>Repair / replace harness, connector, or terminal, securely lock the connector. GO TO 4.
PERFORM SELF-DIAGNOSIS (4)
With CONSULT
Connect 12V battery negative terminal.
Connect brake fluid level switch harness connector.
Connect combination meter harness connector.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C105D-7B” detected?
YES>>GO TO 9.
NO>>INSPECTION END
CHECK BRAKE FLUID LEVEL SWITCH CIRCUIT
Disconnect 12V battery negative terminal.
Disconnect brake fluid level switch harness connector.
Disconnect combination meter harness connector.
Check the continuity between brake fluid level switch harness connector and combination meter harness connector.
Brake fluid level switch Combination meter Continuity Connector Terminal Connector Terminal B40 1 M98 28 Existed Check the continuity between brake fluid level switch harness connector and ground.
Brake fluid level switch — Continuity Connector Terminal B40 1 Ground Not existed
Is the inspection result normal?
YES>>GO TO 10.
NO>>Repair / replace harness or connector. GO TO 10.
CHECK BRAKE FLUID LEVEL SWITCH GROUND CIRCUIT
Check the continuity between brake fluid level switch harness connector and ground.
| Brake fluid level switch | — | Continuity | |
|---|---|---|---|
| Connector | Terminal | ||
| B40 | 2 | Ground | Existed |
Is the inspection result normal?
YES>>GO TO 11.
NO>>Repair / replace harness or connector. GO TO 11.
CHECK COMBINATION METER
Connect brake fluid level switch harness connector.
Connect combination meter harness connector.
Connect 12V battery negative terminal.
Check the combination meter. Refer to On Board Diagnosis Function.
Is the inspection result normal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>Repair or replace integrated interface display. Refer to Removal and Installation.
C105e-92 Pressure Sensor Nissan Ariya first Gen
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C105E | 92 | Pressure sensor not calibration | Diagnosis condition |
|
|
| Signal (terminal) | — | ||||
| Threshold | When a malfunction is detected in electrically-driven intelligent brake unit system. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
Cooperative regenerative brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C105E-92" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT SYSTEM
With CONSULT
Perform self-diagnosis for “BRAKE”.
Is DTC detected?
YES>>Check the DTC. Refer to DTC Index.
NO>>GO TO 2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
PERFORM SELF-DIAGNOSIS
With CONSULT
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC "C105E-92" detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END [Although motor built in the ABS actuator and electric unit (control unit) operates temporarily without a break, this is not a malfunction. Erase the all memory of self-diagnosis results.]
C105e-93 Pressure Sensor Nissan Ariya 2026
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C105E | 93 | Pressure sensor not calibration | Diagnosis condition |
|
|
| Signal (terminal) | — | ||||
| Threshold | When a malfunction is detected in electrically-driven intelligent brake unit system. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
Cooperative regenerative brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C105E-93" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT SYSTEM
With CONSULT
Perform self-diagnosis for “BRAKE”.
Is DTC detected?
YES>>Check the DTC. Refer to DTC Index.
NO>>GO TO 2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
PERFORM SELF-DIAGNOSIS
With CONSULT
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC "C105E-93" detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END [Although motor built in the ABS actuator and electric unit (control unit) operates temporarily without a break, this is not a malfunction. Erase the all memory of self-diagnosis results.]
C105f-85 Control Unit Nissan Ariya first Gen
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C105F | 85 | Control unit | Diagnosis condition |
|
|
| Signal (terminal) | — | ||||
| Threshold | When there is an internal malfunction in the ABS actuator and electric unit (control unit). | ||||
| Diagnosis delay time | 2 seconds or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
Normal control
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C105F-85" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
ADJUST THE NEUTRAL POSITION OF STEERING ANGLE SENSOR
Perform neutral position adjustment of steering angle sensor. Refer to Work Procedure.
Perform “All DTC Reading”.
Is DTC detected?
YES>>Check the DTC.
NO>>GO TO 2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
PERFORM SELF-DIAGNOSIS
With CONSULT
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC "C105F-85" detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END [Although motor built in the ABS actuator and electric unit (control unit) operates temporarily without a break, this is not a malfunction. Erase the all memory of self-diagnosis results.]
C105f-92 Control Unit Nissan Ariya SUV
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C105F | 92 | Control unit | Diagnosis condition |
|
|
| Signal (terminal) | — | ||||
| Threshold | When there is an internal malfunction in the ABS actuator and electric unit (control unit). | ||||
| Diagnosis delay time | 2 seconds or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
Normal control
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C105F-92" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
ADJUST THE NEUTRAL POSITION OF STEERING ANGLE SENSOR
Perform neutral position adjustment of steering angle sensor. Refer to Work Procedure.
Perform “All DTC Reading”.
Is DTC detected?
YES>>Check the DTC.
NO>>GO TO 2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
PERFORM SELF-DIAGNOSIS
With CONSULT
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC "C105F-92" detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END [Although motor built in the ABS actuator and electric unit (control unit) operates temporarily without a break, this is not a malfunction. Erase the all memory of self-diagnosis results.]
C1061-02 Wheel Sensor Nissan Ariya SUV
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1061 | 02 | Front left wheel sensor | Diagnosis condition |
|
|
| Signal (terminal) |
|
||||
| Threshold | When a malfunction is detected in front left wheel sensor. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-02" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK WHEEL SENSOR
Disconnect 12V battery negative terminal.
Check the front left wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 3.
NO>>GO TO 2.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the front left wheel sensor. Refer to FRONT WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-02” detected?
YES>>GO TO 3.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the front left wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 4.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-02” detected?
YES>>GO TO 5.
NO>>INSPECTION END
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 7.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect front left wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-02” detected?
YES>>GO TO 7.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect front left wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and front left wheel sensor harness connector. (Check the continuity while turning steering wheel left and right, or while moving center harness in wheel housing.)
Measurement connector and terminal for power supply circuit
ABS actuator and electric unit (control unit) Front left wheel sensor Continuity Connector Terminal Connector Terminal B2 24 B177 1 Existed Measurement connector and terminal for signal circuit
ABS actuator and electric unit (control unit) Front left wheel sensor Continuity Connector Terminal Connector Terminal B2 7 B177 2 Existed
Is the inspection result normal?
YES>>GO TO 10.
NO>>Repair / replace harness or connector. GO TO 8.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect front left wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-02” detected?
YES>>GO TO 9.
NO>>INSPECTION END
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect front left wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to front left wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 10.
REPLACE WHEEL SENSOR
Replace the front left wheel sensor. Refer to FRONT WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-02” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C1061-07 Wheel Sensor Nissan Ariya 1st generation
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | ||||
|---|---|---|---|---|---|---|
| C1061 | 07 | Front left wheel sensor | 1 | Diagnosis condition |
|
|
| Signal (terminal) | Front left wheel sensor signal | |||||
| Threshold | When distance between front left wheel sensor and front left wheel sensor rotor is large. | |||||
| Diagnosis delay time | 1 – 60 seconds or more | |||||
| 2 | Diagnosis condition |
|
||||
| Signal (terminal) | Front left wheel sensor signal | |||||
| Threshold | When installation of front left wheel sensor is not normal. | |||||
| Diagnosis delay time | 1 – 60 seconds or more | |||||
| 3 | Diagnosis condition |
|
||||
| Signal (terminal) | Front left wheel sensor signal | |||||
| Threshold | When installation of front left sensor rotor is not normal. | |||||
| Diagnosis delay time | 1 – 60 seconds or more | |||||
| 4 | Diagnosis condition |
|
||||
| Signal (terminal) | Front left wheel sensor signal | |||||
| Threshold | When there is contamination on to the front left wheel sensor. | |||||
| Diagnosis delay time | 1 – 60 seconds or more | |||||
| 5 | Diagnosis condition |
|
||||
| Signal (terminal) | Front left wheel sensor signal | |||||
| Threshold | When there is contamination on to the front left sensor rotor. | |||||
| Diagnosis delay time | 1 – 60 seconds or more | |||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-07" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK WHEEL HUB ASSEMBLY
Check that there is no excessive looseness in front left wheel hub assembly. Refer to FRONT WHEEL HUB AND KNUCKLE : Periodic Maintenance Operation.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace the front left wheel hub assembly. Refer to FRONT WHEEL HUB AND KNUCKLE : Removal & Installation. GO TO 2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
CHECK TIRE
Power switch OFF.
Check the front left tire air pressure, wear and size. Refer to TIRE AIR PRESSURE : Service Data.
Is the inspection result normal?
YES>>GO TO 6.
NO>>Adjust air pressure or replace front left tire. GO TO 4.
CHECK DATA MONITOR (1)
With CONSULT
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 5.
NO>>GO TO 6.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-07” detected?
YES>>GO TO 6.
NO>>INSPECTION END
CHECK WHEEL SENSOR AND SENSOR ROTOR
Disconnect 12V battery negative terminal.
Disconnect front left wheel sensor harness connector.
Remove dust and foreign matter adhered to the front left wheel sensor and front left sensor rotor with a vacuum dust collector through the front left wheel sensor mounting hole.
GO TO 7.
CHECK WHEEL SENSOR
Check the front left wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 11.
NO>>GO TO 8.
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect front left wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to front left wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 9.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the front left wheel sensor. Refer to FRONT WHEEL SENSOR : Removal & Installation.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 10.
NO>>GO TO 22.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-07” detected?
YES>>GO TO 22.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the front left wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 14.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 12.
CHECK DATA MONITOR (2)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 13.
NO>>GO TO 14.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-07” detected?
YES>>GO TO 14.
NO>>INSPECTION END
CHECK TERMINAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Disconnect front left wheel sensor harness connector.
Check the front left wheel sensor terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 17.
NO>>Repair / replace harness, connector, or terminal. GO TO 15.
CHECK DATA MONITOR (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect front left wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 16.
NO>>GO TO 17.
PERFORM SELF-DIAGNOSIS (4)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-07” detected?
YES>>GO TO 17.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect front left wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and front left wheel sensor harness connector.
ABS actuator and electric unit (control unit) — Continuity Connector Terminal B2 24, 7 Ground Not existed
Is the inspection result normal?
YES>>GO TO 18.
NO>>Repair / replace harness or connector. GO TO 18.
CHECK DATA MONITOR (4)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect front left wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 19.
NO>>GO TO 20.
PERFORM SELF-DIAGNOSIS (5)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-07” detected?
YES>>GO TO 20.
NO>>INSPECTION END
REPLACE WHEEL SENSOR (2)
With CONSULT
Replace the front left wheel sensor. Refer to FRONT WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 21.
NO>>GO TO 22.
PERFORM SELF-DIAGNOSIS (6)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-07” detected?
YES>>GO TO 22.
NO>>INSPECTION END
REPLACE SENSOR ROTOR
With CONSULT
Replace the front left sensor rotor. Refer to FRONT SENSOR ROTOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-07” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C1061-09 Wheel Sensor Nissan Ariya: FE0
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1061 | 09 | Front left wheel sensor | Diagnosis condition |
|
|
| Signal (terminal) | Front left wheel sensor signal | ||||
| Threshold | When a noise is detected in front left wheel sensor. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-09" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK WHEEL HUB ASSEMBLY
Check that there is no excessive looseness in front left wheel hub assembly. Refer to FRONT WHEEL HUB AND KNUCKLE : Periodic Maintenance Operation.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace the front left wheel hub assembly. Refer to FRONT WHEEL HUB AND KNUCKLE : Removal & Installation. GO TO 2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
CHECK TIRE
Power switch OFF.
Check the front left tire air pressure, wear and size. Refer to TIRE AIR PRESSURE : Service Data.
Is the inspection result normal?
YES>>GO TO 6.
NO>>Adjust air pressure or replace front left tire. GO TO 4.
CHECK DATA MONITOR (1)
With CONSULT
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 5.
NO>>GO TO 6.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-09” detected?
YES>>GO TO 6.
NO>>INSPECTION END
CHECK WHEEL SENSOR AND SENSOR ROTOR
Disconnect 12V battery negative terminal.
Disconnect front left wheel sensor harness connector.
Remove dust and foreign matter adhered to the front left wheel sensor and front left sensor rotor with a vacuum dust collector through the front left wheel sensor mounting hole.
GO TO 7.
CHECK WHEEL SENSOR
Check the front left wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 11.
NO>>GO TO 8.
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect front left wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to front left wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 9.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the front left wheel sensor. Refer to FRONT WHEEL SENSOR : Removal & Installation.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 10.
NO>>GO TO 22.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-09” detected?
YES>>GO TO 22.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the front left wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 14.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 12.
CHECK DATA MONITOR (2)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 13.
NO>>GO TO 14.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-09” detected?
YES>>GO TO 14.
NO>>INSPECTION END
CHECK TERMINAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Disconnect front left wheel sensor harness connector.
Check the front left wheel sensor terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 17.
NO>>Repair / replace harness, connector, or terminal. GO TO 15.
CHECK DATA MONITOR (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect front left wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 16.
NO>>GO TO 17.
PERFORM SELF-DIAGNOSIS (4)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-09” detected?
YES>>GO TO 17.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect front left wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and front left wheel sensor harness connector.
ABS actuator and electric unit (control unit) — Continuity Connector Terminal B2 24, 7 Ground Not existed
Is the inspection result normal?
YES>>GO TO 18.
NO>>Repair / replace harness or connector. GO TO 18.
CHECK DATA MONITOR (4)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect front left wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 19.
NO>>GO TO 20.
PERFORM SELF-DIAGNOSIS (5)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-09” detected?
YES>>GO TO 20.
NO>>INSPECTION END
REPLACE WHEEL SENSOR (2)
With CONSULT
Replace the front left wheel sensor. Refer to Removal and Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 21.
NO>>GO TO 22.
PERFORM SELF-DIAGNOSIS (6)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-09” detected?
YES>>GO TO 22.
NO>>INSPECTION END
REPLACE SENSOR ROTOR
With CONSULT
Replace the front left sensor rotor. Refer to FRONT SENSOR ROTOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-09” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C1061-11 Wheel Sensor Nissan Ariya
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1061 | 11 | Front left wheel sensor | Diagnosis condition |
|
|
| Signal (terminal) |
|
||||
| Threshold | When a short circuit is detected in front left wheel sensor circuit. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-11" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK WHEEL SENSOR
Disconnect 12V battery negative terminal.
Check the front left wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 3.
NO>>GO TO 2.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the front left wheel sensor. Refer to FRONT WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-11” detected?
YES>>GO TO 3.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the front left wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 4.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-11” detected?
YES>>GO TO 5.
NO>>INSPECTION END
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 7.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect front left wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-11” detected?
YES>>GO TO 7.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect front left wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and front left wheel sensor harness connector. (Check the continuity while turning steering wheel left and right, or while moving center harness in wheel housing.)
Measurement connector and terminal for power supply circuit
ABS actuator and electric unit (control unit) Front left wheel sensor Continuity Connector Terminal Connector Terminal B2 24 B177 1 Existed Measurement connector and terminal for signal circuit
ABS actuator and electric unit (control unit) Front left wheel sensor Continuity Connector Terminal Connector Terminal B2 7 B177 2 Existed
Is the inspection result normal?
YES>>GO TO 10.
NO>>Repair / replace harness or connector. GO TO 8.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect front left wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-11” detected?
YES>>GO TO 9.
NO>>INSPECTION END
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect front left wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to front left wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 10.
REPLACE WHEEL SENSOR
Replace the front left wheel sensor. Refer to FRONT WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-11” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C1061-12 Wheel Sensor Nissan Ariya SUV
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1061 | 12 | Front left wheel sensor | Diagnosis condition |
|
|
| Signal (terminal) |
|
||||
| Threshold | When a short circuit is detected in front left wheel sensor circuit. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-12" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK WHEEL SENSOR
Disconnect 12V battery negative terminal.
Check the front left wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 3.
NO>>GO TO 2.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the front left wheel sensor. Refer to FRONT WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-12” detected?
YES>>GO TO 3.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the front left wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 4.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-12” detected?
YES>>GO TO 5.
NO>>INSPECTION END
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 7.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect front left wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-12” detected?
YES>>GO TO 7.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect front left wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and front left wheel sensor harness connector. (Check the continuity while turning steering wheel left and right, or while moving center harness in wheel housing.)
Measurement connector and terminal for power supply circuit
ABS actuator and electric unit (control unit) Front left wheel sensor Continuity Connector Terminal Connector Terminal B2 24 B177 1 Existed Measurement connector and terminal for signal circuit
ABS actuator and electric unit (control unit) Front left wheel sensor Continuity Connector Terminal Connector Terminal B2 7 B177 2 Existed
Is the inspection result normal?
YES>>GO TO 9.
NO>>Repair / replace harness or connector. GO TO 8.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect front left wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-12” detected?
YES>>GO TO 9.
NO>>INSPECTION END
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect front left wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to front left wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 10.
REPLACE WHEEL SENSOR
Replace the front left wheel sensor. Refer to FRONT WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-12” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C1061-13 Wheel Sensor Nissan Ariya 1st generation
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1061 | 13 | Front left wheel sensor | Diagnosis condition |
|
|
| Signal (terminal) |
|
||||
| Threshold | When an open circuit is detected in front left wheel sensor circuit. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-13" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK WHEEL SENSOR
Disconnect 12V battery negative terminal.
Check the front left wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 3.
NO>>GO TO 2.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the front left wheel sensor. Refer to FRONT WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-13” detected?
YES>>GO TO 3.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the front left wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 4.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-13” detected?
YES>>GO TO 5.
NO>>INSPECTION END
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 7.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect front left wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-13” detected?
YES>>GO TO 7.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect front left wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and front left wheel sensor harness connector. (Check the continuity while turning steering wheel left and right, or while moving center harness in wheel housing.)
Measurement connector and terminal for power supply circuit
ABS actuator and electric unit (control unit) Front left wheel sensor Continuity Connector Terminal Connector Terminal B2 24 B177 1 Existed Measurement connector and terminal for signal circuit
ABS actuator and electric unit (control unit) Front left wheel sensor Continuity Connector Terminal Connector Terminal B2 7 B177 2 Existed
Is the inspection result normal?
YES>>GO TO 9.
NO>>Repair / replace harness or connector. GO TO 8.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect front left wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-13” detected?
YES>>GO TO 9.
NO>>INSPECTION END
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect front left wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to front left wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 10.
REPLACE WHEEL SENSOR
Replace the front left wheel sensor. Refer to FRONT WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-13” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C1061-1c Wheel Sensor Nissan Ariya SUV
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1061 | 1C | Front left wheel sensor | Diagnosis condition |
|
|
| Signal (terminal) |
|
||||
| Threshold | When front left wheel sensor power supply out of range. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-1C" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK WHEEL SENSOR
Disconnect 12V battery negative terminal.
Check the front left wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 3.
NO>>GO TO 2.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the front left wheel sensor. Refer to FRONT WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-1C” detected?
YES>>GO TO 3.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the front left wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 4.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-1C” detected?
YES>>GO TO 5.
NO>>INSPECTION END
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 7.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect front left wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-1C” detected?
YES>>GO TO 7.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect front left wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and front left wheel sensor harness connector. (Check the continuity while turning steering wheel left and right, or while moving center harness in wheel housing.)
Measurement connector and terminal for power supply circuit
ABS actuator and electric unit (control unit) Front left wheel sensor Continuity Connector Terminal Connector Terminal B2 24 B177 1 Existed Measurement connector and terminal for signal circuit
ABS actuator and electric unit (control unit) Front left wheel sensor Continuity Connector Terminal Connector Terminal B2 7 B177 2 Existed
Is the inspection result normal?
YES>>GO TO 10.
NO>>Repair / replace harness or connector. GO TO 8.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect front left wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-1C” detected?
YES>>GO TO 9.
NO>>INSPECTION END
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect front left wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to front left wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 10.
REPLACE WHEEL SENSOR
Replace the front left wheel sensor. Refer to FRONT WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-1C” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C1061-38 Wheel Sensor Nissan Ariya SUV
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1061 | 38 | Front left wheel sensor | Diagnosis condition |
|
|
| Signal (terminal) | Front left wheel sensor signal | ||||
| Threshold | When a malfunction is detected in front left wheel sensor signal. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-38" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK WHEEL HUB ASSEMBLY
Check that there is no excessive looseness in front left wheel hub assembly. Refer to FRONT WHEEL HUB AND KNUCKLE : Periodic Maintenance Operation.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace the front left wheel hub assembly. Refer to FRONT WHEEL HUB AND KNUCKLE : Removal & Installation. GO TO 2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
CHECK TIRE
Power switch OFF.
Check the front left tire air pressure, wear and size. Refer to TIRE AIR PRESSURE : Service Data.
Is the inspection result normal?
YES>>GO TO 6.
NO>>Adjust air pressure or replace front left tire. GO TO 4.
CHECK DATA MONITOR (1)
With CONSULT
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 5.
NO>>GO TO 6.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-38” detected?
YES>>GO TO 6.
NO>>INSPECTION END
CHECK WHEEL SENSOR AND SENSOR ROTOR
Disconnect 12V battery negative terminal.
Disconnect front left wheel sensor harness connector.
Remove dust and foreign matter adhered to the front left wheel sensor and front left sensor rotor with a vacuum dust collector through the front left wheel sensor mounting hole.
GO TO 7.
CHECK WHEEL SENSOR
Check the front left wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 11.
NO>>GO TO 8.
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect front left wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to front left wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 9.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the front left wheel sensor. Refer to FRONT WHEEL SENSOR : Removal & Installation.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 10.
NO>>GO TO 22.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-38” detected?
YES>>GO TO 22.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the front left wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 14.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 12.
CHECK DATA MONITOR (2)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 13.
NO>>GO TO 14.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-38” detected?
YES>>GO TO 14.
NO>>INSPECTION END
CHECK TERMINAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Disconnect front left wheel sensor harness connector.
Check the front left wheel sensor terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 17.
NO>>Repair / replace harness, connector, or terminal. GO TO 15.
CHECK DATA MONITOR (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect front left wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 16.
NO>>GO TO 17.
PERFORM SELF-DIAGNOSIS (4)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-38” detected?
YES>>GO TO 17.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect front left wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and front left wheel sensor harness connector.
ABS actuator and electric unit (control unit) — Continuity Connector Terminal B2 24, 7 Ground Not existed
Is the inspection result normal?
YES>>GO TO 18.
NO>>Repair / replace harness or connector. GO TO 18.
CHECK DATA MONITOR (4)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect front left wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 19.
NO>>GO TO 20.
PERFORM SELF-DIAGNOSIS (5)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-38” detected?
YES>>GO TO 20.
NO>>INSPECTION END
REPLACE WHEEL SENSOR (2)
With CONSULT
Replace the front left wheel sensor. Refer to FRONT WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 21.
NO>>GO TO 22.
PERFORM SELF-DIAGNOSIS (6)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-38” detected?
YES>>GO TO 22.
NO>>INSPECTION END
REPLACE SENSOR ROTOR
With CONSULT
Replace the front left sensor rotor. Refer to FRONT SENSOR ROTOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-38” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C1061-4a Wheel Sensor Nissan Ariya 2026
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1061 | 4A | Front left wheel sensor | Diagnosis condition |
|
|
| Signal (terminal) |
|
||||
| Threshold | When front left wheel sensor is installed to wrong position. | ||||
| Diagnosis delay time | 3 seconds or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-4A" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK SELF-DIAGNOSIS RESULT
With CONSULT
Check the self-diagnosis result for "ABS".
Is the display result "C1061-4A" of “CRNT”?
YES>>GO TO 2.
NO>>Erase self-diagnosis result for “ABS”.
REPLACE WHEEL SENSOR
Replace the front left wheel sensor. Refer to FRONT WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is the display result "C1061-4A" of “CRNT”?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>Erase self-diagnosis result for “ABS”.
C1061-64 Wheel Sensor Nissan Ariya 2026
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1061 | 64 | Front left wheel sensor | Diagnosis condition |
|
|
| Signal (terminal) | Front left wheel sensor signal | ||||
| Threshold | When difference between front left wheel and other front left wheel speed is detected the Nissan Ariya vehicle is driven, because of installation of other tires than specified. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-64" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK WHEEL HUB ASSEMBLY
Check that there is no excessive looseness in front left wheel hub assembly. Refer to FRONT WHEEL HUB AND KNUCKLE : Periodic Maintenance Operation.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace the front left wheel hub assembly. Refer to FRONT WHEEL HUB AND KNUCKLE : Removal & Installation. GO TO 2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
CHECK TIRE
Power switch OFF.
Check the front left tire air pressure, wear and size. Refer to TIRE AIR PRESSURE : Service Data.
Is the inspection result normal?
YES>>GO TO 6.
NO>>Adjust air pressure or replace front left tire. GO TO 4.
CHECK DATA MONITOR (1)
With CONSULT
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 5.
NO>>GO TO 6.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-64” detected?
YES>>GO TO 6.
NO>>INSPECTION END
CHECK WHEEL SENSOR AND SENSOR ROTOR
Disconnect 12V battery negative terminal.
Disconnect front left wheel sensor harness connector.
Remove dust and foreign matter adhered to the front left wheel sensor and front left sensor rotor with a vacuum dust collector through the front left wheel sensor mounting hole.
GO TO 7.
CHECK WHEEL SENSOR
Check the front left wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 11.
NO>>GO TO 8.
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect front left wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to front left wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 9.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the front left wheel sensor. Refer to FRONT WHEEL SENSOR : Removal & Installation.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 10.
NO>>GO TO 22.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-64” detected?
YES>>GO TO 22.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the front left wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 14.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 12.
CHECK DATA MONITOR (2)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 13.
NO>>GO TO 14.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-64” detected?
YES>>GO TO 14.
NO>>INSPECTION END
CHECK TERMINAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Disconnect front left wheel sensor harness connector.
Check the front left wheel sensor terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 17.
NO>>Repair / replace harness, connector, or terminal. GO TO 15.
CHECK DATA MONITOR (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect front left wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 16.
NO>>GO TO 17.
PERFORM SELF-DIAGNOSIS (4)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-64” detected?
YES>>GO TO 17.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect front left wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and front left wheel sensor harness connector.
ABS actuator and electric unit (control unit) — Continuity Connector Terminal B2 24, 7 Ground Not existed
Is the inspection result normal?
YES>>GO TO 18.
NO>>Repair / replace harness or connector. GO TO 18.
CHECK DATA MONITOR (4)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect front left wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 19.
NO>>GO TO 20.
PERFORM SELF-DIAGNOSIS (5)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-64” detected?
YES>>GO TO 20.
NO>>INSPECTION END
REPLACE WHEEL SENSOR (2)
With CONSULT
Replace the front left wheel sensor. Refer to FRONT WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 21.
NO>>GO TO 22.
PERFORM SELF-DIAGNOSIS (6)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-64” detected?
YES>>GO TO 22.
NO>>INSPECTION END
REPLACE SENSOR ROTOR
With CONSULT
Replace the front left sensor rotor. Refer to FRONT SENSOR ROTOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-64” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C1061-92 Wheel Sensor Nissan Ariya 1st generation
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1061 | 92 | Front left wheel sensor | Diagnosis condition |
|
|
| Signal (terminal) | Front left wheel sensor signal | ||||
| Threshold | When a malfunction is detected in front left wheel sensor signal. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-92" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK WHEEL HUB ASSEMBLY
Check that there is no excessive looseness in front left wheel hub assembly. Refer to FRONT WHEEL HUB AND KNUCKLE : Periodic Maintenance Operation.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace the front left wheel hub assembly. Refer to FRONT WHEEL HUB AND KNUCKLE : Removal & Installation. GO TO 2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
CHECK TIRE
Power switch OFF.
Check the front left tire air pressure, wear and size. Refer to TIRE AIR PRESSURE : Service Data.
Is the inspection result normal?
YES>>GO TO 6.
NO>>Adjust air pressure or replace front left tire. GO TO 4.
CHECK DATA MONITOR (1)
With CONSULT
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 5.
NO>>GO TO 6.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-92” detected?
YES>>GO TO 6.
NO>>INSPECTION END
CHECK WHEEL SENSOR AND SENSOR ROTOR
Disconnect 12V battery negative terminal.
Disconnect front left wheel sensor harness connector.
Remove dust and foreign matter adhered to the front left wheel sensor and front left sensor rotor with a vacuum dust collector through the front left wheel sensor mounting hole.
GO TO 7.
CHECK WHEEL SENSOR
Check the front left wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 11.
NO>>GO TO 8.
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect front left wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to front left wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 9.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the front left wheel sensor. Refer to FRONT WHEEL SENSOR : Removal & Installation.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 10.
NO>>GO TO 22.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-92” detected?
YES>>GO TO 22.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the front left wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 14.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 12.
CHECK DATA MONITOR (2)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 13.
NO>>GO TO 14.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-92” detected?
YES>>GO TO 14.
NO>>INSPECTION END
CHECK TERMINAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Disconnect front left wheel sensor harness connector.
Check the front left wheel sensor terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 17.
NO>>Repair / replace harness, connector, or terminal. GO TO 15.
CHECK DATA MONITOR (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect front left wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 16.
NO>>GO TO 17.
PERFORM SELF-DIAGNOSIS (4)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-92” detected?
YES>>GO TO 17.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect front left wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and front left wheel sensor harness connector.
ABS actuator and electric unit (control unit) — Continuity Connector Terminal B2 24, 7 Ground Not existed
Is the inspection result normal?
YES>>GO TO 18.
NO>>Repair / replace harness or connector. GO TO 18.
CHECK DATA MONITOR (4)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect front left wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 19.
NO>>GO TO 20.
PERFORM SELF-DIAGNOSIS (5)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-92” detected?
YES>>GO TO 20.
NO>>INSPECTION END
REPLACE WHEEL SENSOR (2)
With CONSULT
Replace the front left wheel sensor. Refer to FRONT WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 21.
NO>>GO TO 22.
PERFORM SELF-DIAGNOSIS (6)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-92” detected?
YES>>GO TO 22.
NO>>INSPECTION END
REPLACE SENSOR ROTOR
With CONSULT
Replace the front left sensor rotor. Refer to FRONT SENSOR ROTOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1061-92” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C1063-02 Wheel Sensor Nissan Ariya 2023
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1063 | 02 | Front right wheel sensor | Diagnosis condition |
|
|
| Signal (terminal) |
|
||||
| Threshold | When a malfunction is detected in front right wheel sensor. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-02" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK WHEEL SENSOR
Disconnect 12V battery negative terminal.
Check the front right wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 3.
NO>>GO TO 2.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the front right wheel sensor. Refer to FRONT WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-02” detected?
YES>>GO TO 3.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the front right wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 4.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-02” detected?
YES>>GO TO 5.
NO>>INSPECTION END
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 7.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect front right wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-02” detected?
YES>>GO TO 7.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect front right wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and front right wheel sensor harness connector. (Check the continuity while turning steering wheel left and right, or while moving center harness in wheel housing.)
Measurement connector and terminal for power supply circuit
ABS actuator and electric unit (control unit) Front right wheel sensor Continuity Connector Terminal Connector Terminal B2 21 E109 1 Existed Measurement connector and terminal for signal circuit
ABS actuator and electric unit (control unit) Front right wheel sensor Continuity Connector Terminal Connector Terminal B2 26 E109 2 Existed
Is the inspection result normal?
YES>>GO TO 10.
NO>>Repair / replace harness or connector. GO TO 8.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect front right wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-02” detected?
YES>>GO TO 9.
NO>>INSPECTION END
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect front right wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to front right wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 10.
REPLACE WHEEL SENSOR
Replace the front right wheel sensor. Refer to FRONT WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-02” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C1063-07 Wheel Sensor Nissan Ariya SUV
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | ||||
|---|---|---|---|---|---|---|
| C1063 | 07 | Front right wheel sensor | 1 | Diagnosis condition |
|
|
| Signal (terminal) | Front right wheel sensor signal | |||||
| Threshold | When distance between front right wheel sensor and front right wheel sensor rotor is large. | |||||
| Diagnosis delay time | 1 - 60 seconds or more | |||||
| 2 | Diagnosis condition |
|
||||
| Signal (terminal) | Front right wheel sensor signal | |||||
| Threshold | When installation of front right wheel sensor is not normal. | |||||
| Diagnosis delay time | 1 - 60 seconds or more | |||||
| 3 | Diagnosis condition |
|
||||
| Signal (terminal) | Front right wheel sensor signal | |||||
| Threshold | When installation of front right sensor rotor is not normal. | |||||
| Diagnosis delay time | 1 - 60 seconds or more | |||||
| 4 | Diagnosis condition |
|
||||
| Signal (terminal) | Front right wheel sensor signal | |||||
| Threshold | When there is contamination on to the front right wheel sensor. | |||||
| Diagnosis delay time | 1 - 60 seconds or more | |||||
| 5 | Diagnosis condition |
|
||||
| Signal (terminal) | Front right wheel sensor signal | |||||
| Threshold | When there is contamination on to the front right sensor rotor. | |||||
| Diagnosis delay time | 1 - 60 seconds or more | |||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-07" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK WHEEL HUB ASSEMBLY
Check that there is no excessive looseness in front right wheel hub assembly. Refer to FRONT WHEEL HUB AND KNUCKLE : Periodic Maintenance Operation.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace the front right wheel hub assembly. Refer to FRONT WHEEL HUB AND KNUCKLE : Removal & Installation. GO TO 2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
CHECK TIRE
Power switch OFF.
Check the front right tire air pressure, wear and size. Refer to TIRE AIR PRESSURE : Service Data.
Is the inspection result normal?
YES>>GO TO 6.
NO>>Adjust air pressure or replace front right tire. GO TO 4.
CHECK DATA MONITOR (1)
With CONSULT
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 5.
NO>>GO TO 6.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-07” detected?
YES>>GO TO 6.
NO>>INSPECTION END
CHECK WHEEL SENSOR AND SENSOR ROTOR
Disconnect 12V battery negative terminal.
Disconnect front right wheel sensor harness connector.
Remove dust and foreign matter adhered to the front right wheel sensor and front right sensor rotor with a vacuum dust collector through the front right wheel sensor mounting hole.
GO TO 7.
CHECK WHEEL SENSOR
Check the front right wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 11.
NO>>GO TO 8.
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect front right wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to front right wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 9.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the front right wheel sensor. Refer to FRONT WHEEL SENSOR : Removal & Installation.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 10.
NO>>GO TO 22.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-07” detected?
YES>>GO TO 22.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the front right wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 14.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 12.
CHECK DATA MONITOR (2)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 13.
NO>>GO TO 14.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-07” detected?
YES>>GO TO 14.
NO>>INSPECTION END
CHECK TERMINAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Disconnect front right wheel sensor harness connector.
Check the front right wheel sensor terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 17.
NO>>Repair / replace harness, connector, or terminal. GO TO 15.
CHECK DATA MONITOR (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect front right wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 16.
NO>>GO TO 17.
PERFORM SELF-DIAGNOSIS (4)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-07” detected?
YES>>GO TO 17.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect front right wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and front right wheel sensor harness connector.
ABS actuator and electric unit (control unit) — Continuity Connector Terminal B2 21, 26 Ground Not existed
Is the inspection result normal?
YES>>GO TO 18.
NO>>Repair / replace harness or connector. GO TO 18.
CHECK DATA MONITOR (4)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect front right wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 19.
NO>>GO TO 20.
PERFORM SELF-DIAGNOSIS (5)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-07” detected?
YES>>GO TO 20.
NO>>INSPECTION END
REPLACE WHEEL SENSOR (2)
With CONSULT
Replace the front right wheel sensor. Refer to FRONT WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 21.
NO>>GO TO 22.
PERFORM SELF-DIAGNOSIS (6)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-07” detected?
YES>>GO TO 22.
NO>>INSPECTION END
REPLACE SENSOR ROTOR
With CONSULT
Replace the front right sensor rotor. Refer to FRONT SENSOR ROTOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-07” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C1063-09 Wheel Sensor Nissan Ariya SUV
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1063 | 09 | Front right wheel sensor | Diagnosis condition |
|
|
| Signal (terminal) | Front right wheel sensor signal | ||||
| Threshold | When a noise is detected in front right wheel sensor. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-09" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK WHEEL HUB ASSEMBLY
Check that there is no excessive looseness in front right wheel hub assembly. Refer to FRONT WHEEL HUB AND KNUCKLE : Periodic Maintenance Operation.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace the front right wheel hub assembly. Refer to FRONT WHEEL HUB AND KNUCKLE : Removal & Installation. GO TO 2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
CHECK TIRE
Power switch OFF.
Check the front right tire air pressure, wear and size. Refer to TIRE AIR PRESSURE : Service Data.
Is the inspection result normal?
YES>>GO TO 6.
NO>>Adjust air pressure or replace front right tire. GO TO 4.
CHECK DATA MONITOR (1)
With CONSULT
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 5.
NO>>GO TO 6.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-09” detected?
YES>>GO TO 6.
NO>>INSPECTION END
CHECK WHEEL SENSOR AND SENSOR ROTOR
Disconnect 12V battery negative terminal.
Disconnect front right wheel sensor harness connector.
Remove dust and foreign matter adhered to the front right wheel sensor and front right sensor rotor with a vacuum dust collector through the front right wheel sensor mounting hole.
GO TO 7.
CHECK WHEEL SENSOR
Check the front right wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 11.
NO>>GO TO 8.
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect front right wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to front right wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 9.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the front right wheel sensor. Refer to FRONT WHEEL SENSOR : Removal & Installation.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 10.
NO>>GO TO 22.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-09” detected?
YES>>GO TO 22.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the front right wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 14.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 12.
CHECK DATA MONITOR (2)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 13.
NO>>GO TO 14.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-09” detected?
YES>>GO TO 14.
NO>>INSPECTION END
CHECK TERMINAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Disconnect front right wheel sensor harness connector.
Check the front right wheel sensor terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 17.
NO>>Repair / replace harness, connector, or terminal. GO TO 15.
CHECK DATA MONITOR (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect front right wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 16.
NO>>GO TO 17.
PERFORM SELF-DIAGNOSIS (4)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-09” detected?
YES>>GO TO 17.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect front right wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and front right wheel sensor harness connector.
ABS actuator and electric unit (control unit) — Continuity Connector Terminal B2 21, 26 Ground Not existed
Is the inspection result normal?
YES>>GO TO 18.
NO>>Repair / replace harness or connector. GO TO 18.
CHECK DATA MONITOR (4)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect front right wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 19.
NO>>GO TO 20.
PERFORM SELF-DIAGNOSIS (5)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-09” detected?
YES>>GO TO 20.
NO>>INSPECTION END
REPLACE WHEEL SENSOR (2)
With CONSULT
Replace the front right wheel sensor. Refer to FRONT WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 21.
NO>>GO TO 22.
PERFORM SELF-DIAGNOSIS (6)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-09” detected?
YES>>GO TO 22.
NO>>INSPECTION END
REPLACE SENSOR ROTOR
With CONSULT
Replace the front right sensor rotor. Refer to FRONT SENSOR ROTOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-09” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C1063-11 Wheel Sensor Nissan Ariya SUV
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1063 | 11 | Front right wheel sensor | Diagnosis condition |
|
|
| Signal (terminal) |
|
||||
| Threshold | When a short circuit is detected in front right wheel sensor circuit. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-11" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK WHEEL SENSOR
Disconnect 12V battery negative terminal.
Check the front right wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 3.
NO>>GO TO 2.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the front right wheel sensor. Refer to FRONT WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-11” detected?
YES>>GO TO 3.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the front right wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 4.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-11” detected?
YES>>GO TO 5.
NO>>INSPECTION END
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 7.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect front right wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-11” detected?
YES>>GO TO 7.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect front right wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and front right wheel sensor harness connector. (Check the continuity while turning steering wheel left and right, or while moving center harness in wheel housing.)
Measurement connector and terminal for power supply circuit
ABS actuator and electric unit (control unit) Front right wheel sensor Continuity Connector Terminal Connector Terminal B2 21 E109 1 Existed Measurement connector and terminal for signal circuit
ABS actuator and electric unit (control unit) Front right wheel sensor Continuity Connector Terminal Connector Terminal B2 26 E109 2 Existed
Is the inspection result normal?
YES>>GO TO 10.
NO>>Repair / replace harness or connector. GO TO 8.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect front right wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-11” detected?
YES>>GO TO 9.
NO>>INSPECTION END
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect front right wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to front right wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 10.
REPLACE WHEEL SENSOR
Replace the front right wheel sensor. Refer to FRONT WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-11” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C1063-12 Wheel Sensor Nissan Ariya first Gen
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1063 | 12 | Front right wheel sensor | Diagnosis condition |
|
|
| Signal (terminal) |
|
||||
| Threshold | When a short circuit is detected in front right wheel sensor circuit. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-12" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK WHEEL SENSOR
Disconnect 12V battery negative terminal.
Check the front right wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 3.
NO>>GO TO 2.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the front right wheel sensor. Refer to FRONT WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-12” detected?
YES>>GO TO 3.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the front right wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 4.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-12” detected?
YES>>GO TO 5.
NO>>INSPECTION END
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 7.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect front right wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-12” detected?
YES>>GO TO 7.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect front right wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and front right wheel sensor harness connector. (Check the continuity while turning steering wheel left and right, or while moving center harness in wheel housing.)
Measurement connector and terminal for power supply circuit
ABS actuator and electric unit (control unit) Front right wheel sensor Continuity Connector Terminal Connector Terminal B2 21 E109 1 Existed Measurement connector and terminal for signal circuit
ABS actuator and electric unit (control unit) Front right wheel sensor Continuity Connector Terminal Connector Terminal B2 26 E109 2 Existed
Is the inspection result normal?
YES>>GO TO 10.
NO>>Repair / replace harness or connector. GO TO 8.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect front right wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-12” detected?
YES>>GO TO 9.
NO>>INSPECTION END
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect front right wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to front right wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 10.
REPLACE WHEEL SENSOR
Replace the front right wheel sensor. Refer to FRONT WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-12” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C1063-13 Wheel Sensor Nissan Ariya 2026
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1063 | 13 | Front right wheel sensor | Diagnosis condition |
|
|
| Signal (terminal) |
|
||||
| Threshold | When an open circuit is detected in front right wheel sensor circuit. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-13" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK WHEEL SENSOR
Disconnect 12V battery negative terminal.
Check the front right wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 3.
NO>>GO TO 2.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the front right wheel sensor. Refer to FRONT WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-13” detected?
YES>>GO TO 3.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the front right wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 4.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-13” detected?
YES>>GO TO 5.
NO>>INSPECTION END
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 7.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect front right wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-13” detected?
YES>>GO TO 7.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect front right wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and front right wheel sensor harness connector. (Check the continuity while turning steering wheel left and right, or while moving center harness in wheel housing.)
Measurement connector and terminal for power supply circuit
ABS actuator and electric unit (control unit) Front right wheel sensor Continuity Connector Terminal Connector Terminal B2 21 E109 1 Existed Measurement connector and terminal for signal circuit
ABS actuator and electric unit (control unit) Front right wheel sensor Continuity Connector Terminal Connector Terminal B2 26 E109 2 Existed
Is the inspection result normal?
YES>>GO TO 9.
NO>>Repair / replace harness or connector. GO TO 8.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect front right wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-13” detected?
YES>>GO TO 9.
NO>>INSPECTION END
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect front right wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to front right wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 10.
REPLACE WHEEL SENSOR
Replace the front right wheel sensor. Refer to FRONT WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-13” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C1063-1c Wheel Sensor Nissan Ariya 2023
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1063 | 1C | Front right wheel sensor | Diagnosis condition |
|
|
| Signal (terminal) |
|
||||
| Threshold | When front right wheel sensor power supply out of range. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-1C" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK WHEEL SENSOR
Disconnect 12V battery negative terminal.
Check the front right wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 3.
NO>>GO TO 2.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the front right wheel sensor. Refer to FRONT WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-1C” detected?
YES>>GO TO 3.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the front right wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 4.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-1C” detected?
YES>>GO TO 5.
NO>>INSPECTION END
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 7.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect front right wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-1C” detected?
YES>>GO TO 7.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect front right wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and front right wheel sensor harness connector. (Check the continuity while turning steering wheel left and right, or while moving center harness in wheel housing.)
Measurement connector and terminal for power supply circuit
ABS actuator and electric unit (control unit) Front right wheel sensor Continuity Connector Terminal Connector Terminal B2 21 E109 1 Existed Measurement connector and terminal for signal circuit
ABS actuator and electric unit (control unit) Front right wheel sensor Continuity Connector Terminal Connector Terminal B2 26 E109 2 Existed
Is the inspection result normal?
YES>>GO TO 10.
NO>>Repair / replace harness or connector. GO TO 8.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect front right wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-1C” detected?
YES>>GO TO 9.
NO>>INSPECTION END
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect front right wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to front right wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 10.
REPLACE WHEEL SENSOR
Replace the front right wheel sensor. Refer to FRONT WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-1C” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C1063-38 Wheel Sensor Nissan Ariya 2023
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1063 | 38 | Front right wheel sensor | Diagnosis condition |
|
|
| Signal (terminal) | Front right wheel sensor signal | ||||
| Threshold | When a malfunction is detected in front right wheel sensor signal. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-38" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK WHEEL HUB ASSEMBLY
Check that there is no excessive looseness in front right wheel hub assembly. Refer to FRONT WHEEL HUB AND KNUCKLE : Periodic Maintenance Operation.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace the front right wheel hub assembly. Refer to FRONT WHEEL HUB AND KNUCKLE : Removal & Installation. GO TO 2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
CHECK TIRE
Power switch OFF.
Check the front right tire air pressure, wear and size. Refer to TIRE AIR PRESSURE : Service Data.
Is the inspection result normal?
YES>>GO TO 6.
NO>>Adjust air pressure or replace front right tire. GO TO 4.
CHECK DATA MONITOR (1)
With CONSULT
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 5.
NO>>GO TO 6.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-38” detected?
YES>>GO TO 6.
NO>>INSPECTION END
CHECK WHEEL SENSOR AND SENSOR ROTOR
Disconnect 12V battery negative terminal.
Disconnect front right wheel sensor harness connector.
Remove dust and foreign matter adhered to the front right wheel sensor and front right sensor rotor with a vacuum dust collector through the front right wheel sensor mounting hole.
GO TO 7.
CHECK WHEEL SENSOR
Check the front right wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 11.
NO>>GO TO 8.
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect front right wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to front right wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 9.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the front right wheel sensor. Refer to FRONT WHEEL SENSOR : Removal & Installation.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 10.
NO>>GO TO 22.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-38” detected?
YES>>GO TO 22.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the front right wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 14.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 12.
CHECK DATA MONITOR (2)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 13.
NO>>GO TO 14.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-38” detected?
YES>>GO TO 14.
NO>>INSPECTION END
CHECK TERMINAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Disconnect front right wheel sensor harness connector.
Check the front right wheel sensor terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 17.
NO>>Repair / replace harness, connector, or terminal. GO TO 15.
CHECK DATA MONITOR (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect front right wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 16.
NO>>GO TO 17.
PERFORM SELF-DIAGNOSIS (4)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-38” detected?
YES>>GO TO 17.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect front right wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and front right wheel sensor harness connector.
ABS actuator and electric unit (control unit) — Continuity Connector Terminal B2 21, 26 Ground Not existed
Is the inspection result normal?
YES>>GO TO 18.
NO>>Repair / replace harness or connector. GO TO 18.
CHECK DATA MONITOR (4)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect front right wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 19.
NO>>GO TO 20.
PERFORM SELF-DIAGNOSIS (5)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-38” detected?
YES>>GO TO 20.
NO>>INSPECTION END
REPLACE WHEEL SENSOR (2)
With CONSULT
Replace the front right wheel sensor. Refer to FRONT WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 21.
NO>>GO TO 22.
PERFORM SELF-DIAGNOSIS (6)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-38” detected?
YES>>GO TO 22.
NO>>INSPECTION END
REPLACE SENSOR ROTOR
With CONSULT
Replace the front right sensor rotor. Refer to FRONT SENSOR ROTOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-38” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C1063-4a Wheel Sensor Nissan Ariya SUV
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1063 | 4A | Front right wheel sensor | Diagnosis condition |
|
|
| Signal (terminal) |
|
||||
| Threshold | When front right wheel sensor is installed to wrong position. | ||||
| Diagnosis delay time | 3 seconds or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-4A" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK SELF-DIAGNOSIS RESULT
With CONSULT
Check the self-diagnosis result for "ABS".
Is the display result "C1063-4A" of “CRNT”?
YES>>GO TO 2.
NO>>Erase self-diagnosis result for “ABS”.
REPLACE WHEEL SENSOR
Replace the front right wheel sensor. Refer to FRONT WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is the display result "C1063-4A" of “CRNT”?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>Erase self-diagnosis result for “ABS”.
C1063-64 Wheel Sensor Nissan Ariya
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1063 | 64 | Front right wheel sensor | Diagnosis condition |
|
|
| Signal (terminal) | Front right wheel sensor signal | ||||
| Threshold | When difference between front right wheel and other front right wheel speed is detected the Nissan Ariya vehicle is driven, because of installation of other tires than specified. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-64" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK WHEEL HUB ASSEMBLY
Check that there is no excessive looseness in front right wheel hub assembly. Refer to FRONT WHEEL HUB AND KNUCKLE : Periodic Maintenance Operation.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace the front right wheel hub assembly. Refer to FRONT WHEEL HUB AND KNUCKLE : Removal & Installation. GO TO 2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
CHECK TIRE
Power switch OFF.
Check the front right tire air pressure, wear and size. Refer to TIRE AIR PRESSURE : Service Data.
Is the inspection result normal?
YES>>GO TO 6.
NO>>Adjust air pressure or replace front right tire. GO TO 4.
CHECK DATA MONITOR (1)
With CONSULT
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 5.
NO>>GO TO 6.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-64” detected?
YES>>GO TO 6.
NO>>INSPECTION END
CHECK WHEEL SENSOR AND SENSOR ROTOR
Disconnect 12V battery negative terminal.
Disconnect front right wheel sensor harness connector.
Remove dust and foreign matter adhered to the front right wheel sensor and front right sensor rotor with a vacuum dust collector through the front right wheel sensor mounting hole.
GO TO 7.
CHECK WHEEL SENSOR
Check the front right wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 11.
NO>>GO TO 8.
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect front right wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to front right wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 9.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the front right wheel sensor. Refer to FRONT WHEEL SENSOR : Removal & Installation.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 10.
NO>>GO TO 22.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-64” detected?
YES>>GO TO 22.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the front right wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 14.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 12.
CHECK DATA MONITOR (2)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 13.
NO>>GO TO 14.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-64” detected?
YES>>GO TO 14.
NO>>INSPECTION END
CHECK TERMINAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Disconnect front right wheel sensor harness connector.
Check the front right wheel sensor terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 17.
NO>>Repair / replace harness, connector, or terminal. GO TO 15.
CHECK DATA MONITOR (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect front right wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 16.
NO>>GO TO 17.
PERFORM SELF-DIAGNOSIS (4)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-64” detected?
YES>>GO TO 17.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect front right wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and front right wheel sensor harness connector.
ABS actuator and electric unit (control unit) — Continuity Connector Terminal B2 21, 26 Ground Not existed
Is the inspection result normal?
YES>>GO TO 18.
NO>>Repair / replace harness or connector. GO TO 18.
CHECK DATA MONITOR (4)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect front right wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 19.
NO>>GO TO 20.
PERFORM SELF-DIAGNOSIS (5)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-64” detected?
YES>>GO TO 20.
NO>>INSPECTION END
REPLACE WHEEL SENSOR (2)
With CONSULT
Replace the front right wheel sensor. Refer to FRONT WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 21.
NO>>GO TO 22.
PERFORM SELF-DIAGNOSIS (6)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-64” detected?
YES>>GO TO 22.
NO>>INSPECTION END
REPLACE SENSOR ROTOR
With CONSULT
Replace the front right sensor rotor. Refer to FRONT SENSOR ROTOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-64” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C1063-92 Wheel Sensor Nissan Ariya 1st generation
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1063 | 92 | Front right wheel sensor | Diagnosis condition |
|
|
| Signal (terminal) | Front right wheel sensor signal | ||||
| Threshold | When a malfunction is detected in front right wheel sensor signal. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-92" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK WHEEL HUB ASSEMBLY
Check that there is no excessive looseness in front right wheel hub assembly. Refer to FRONT WHEEL HUB AND KNUCKLE : Periodic Maintenance Operation.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace the front right wheel hub assembly. Refer to FRONT WHEEL HUB AND KNUCKLE : Removal & Installation. GO TO 2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
CHECK TIRE
Power switch OFF.
Check the front right tire air pressure, wear and size. Refer to TIRE AIR PRESSURE : Service Data.
Is the inspection result normal?
YES>>GO TO 6.
NO>>Adjust air pressure or replace front right tire. GO TO 4.
CHECK DATA MONITOR (1)
With CONSULT
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 5.
NO>>GO TO 6.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-92” detected?
YES>>GO TO 6.
NO>>INSPECTION END
CHECK WHEEL SENSOR AND SENSOR ROTOR
Disconnect 12V battery negative terminal.
Disconnect front right wheel sensor harness connector.
Remove dust and foreign matter adhered to the front right wheel sensor and front right sensor rotor with a vacuum dust collector through the front right wheel sensor mounting hole.
GO TO 7.
CHECK WHEEL SENSOR
Check the front right wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 11.
NO>>GO TO 8.
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect front right wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to front right wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 9.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the front right wheel sensor. Refer to FRONT WHEEL SENSOR : Removal & Installation.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 10.
NO>>GO TO 22.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-92” detected?
YES>>GO TO 22.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the front right wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 14.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 12.
CHECK DATA MONITOR (2)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 13.
NO>>GO TO 14.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-92” detected?
YES>>GO TO 14.
NO>>INSPECTION END
CHECK TERMINAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Disconnect front right wheel sensor harness connector.
Check the front right wheel sensor terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 17.
NO>>Repair / replace harness, connector, or terminal. GO TO 15.
CHECK DATA MONITOR (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect front right wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 16.
NO>>GO TO 17.
PERFORM SELF-DIAGNOSIS (4)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-92” detected?
YES>>GO TO 17.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect front right wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and front right wheel sensor harness connector.
ABS actuator and electric unit (control unit) — Continuity Connector Terminal B2 21, 26 Ground Not existed
Is the inspection result normal?
YES>>GO TO 18.
NO>>Repair / replace harness or connector. GO TO 18.
CHECK DATA MONITOR (4)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect front right wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 19.
NO>>GO TO 20.
PERFORM SELF-DIAGNOSIS (5)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-92” detected?
YES>>GO TO 20.
NO>>INSPECTION END
REPLACE WHEEL SENSOR (2)
With CONSULT
Replace the front right wheel sensor. Refer to FRONT WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 21.
NO>>GO TO 22.
PERFORM SELF-DIAGNOSIS (6)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-92” detected?
YES>>GO TO 22.
NO>>INSPECTION END
REPLACE SENSOR ROTOR
With CONSULT
Replace the front right sensor rotor. Refer to FRONT SENSOR ROTOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1063-92” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C1065-02 Wheel Sensor Nissan Ariya first Gen
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1065 | 02 | Rear left wheel sensor | Diagnosis condition |
|
|
| Signal (terminal) |
|
||||
| Threshold | When a malfunction is detected in rear left wheel sensor. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-02" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK WHEEL SENSOR
Disconnect 12V battery negative terminal.
Check the rear left wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 3.
NO>>GO TO 2.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the rear left wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-02” detected?
YES>>GO TO 3.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the rear left wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 4.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-02” detected?
YES>>GO TO 5.
NO>>INSPECTION END
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 7.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect rear left wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-02” detected?
YES>>GO TO 7.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect rear left wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and rear left wheel sensor harness connector. (Check the continuity while turning steering wheel left and right, or while moving center harness in wheel housing.)
Measurement connector and terminal for power supply circuit
ABS actuator and electric unit (control unit) Rear left wheel sensor Continuity Connector Terminal Connector Terminal B2 39 B178 1 Existed Measurement connector and terminal for signal circuit
ABS actuator and electric unit (control unit) Rear left wheel sensor Continuity Connector Terminal Connector Terminal B2 23 B178 2 Existed
Is the inspection result normal?
YES>>GO TO 10.
NO>>Repair / replace harness or connector. GO TO 8.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect rear left wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-02” detected?
YES>>GO TO 9.
NO>>INSPECTION END
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect rear left wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to rear left wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 10.
REPLACE WHEEL SENSOR
Replace the rear left wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-02” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C1065-07 Wheel Sensor Nissan Ariya SUV
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | ||||
|---|---|---|---|---|---|---|
| C1065 | 07 | Rear left wheel sensor | 1 | Diagnosis condition |
|
|
| Signal (terminal) | Rear left wheel sensor signal | |||||
| Threshold | When distance between rear left wheel sensor and rear left wheel sensor rotor is large. | |||||
| Diagnosis delay time | 1 - 60 seconds or more | |||||
| 2 | Diagnosis condition |
|
||||
| Signal (terminal) | Rear left wheel sensor signal | |||||
| Threshold | When installation of rear left wheel sensor is not normal. | |||||
| Diagnosis delay time | 1 - 60 seconds or more | |||||
| 3 | Diagnosis condition |
|
||||
| Signal (terminal) | Rear left wheel sensor signal | |||||
| Threshold | When installation of rear left sensor rotor is not normal. | |||||
| Diagnosis delay time | 1 - 60 seconds or more | |||||
| 4 | Diagnosis condition |
|
||||
| Signal (terminal) | Rear left wheel sensor signal | |||||
| Threshold | When there is contamination on to the rear left wheel sensor. | |||||
| Diagnosis delay time | 1 - 60 seconds or more | |||||
| 5 | Diagnosis condition |
|
||||
| Signal (terminal) | Rear left wheel sensor signal | |||||
| Threshold | When there is contamination on to the rear left sensor rotor. | |||||
| Diagnosis delay time | 1 - 60 seconds or more | |||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-07" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK WHEEL HUB ASSEMBLY
Check that there is no excessive looseness in rear left wheel hub assembly. Refer to REAR WHEEL HUB : Periodic Maintenance Operation.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace the rear left wheel hub assembly. Refer to REAR WHEEL HUB : Removal & Installation. GO TO 2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
CHECK TIRE
Power switch OFF.
Check the rear left tire air pressure, wear and size. Refer to TIRE AIR PRESSURE : Service Data.
Is the inspection result normal?
YES>>GO TO 6.
NO>>Adjust air pressure or replace rear left tire. GO TO 4.
CHECK DATA MONITOR (1)
With CONSULT
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 5.
NO>>GO TO 6.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Never operate the vehicle.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-07” detected?
YES>>GO TO 6.
NO>>INSPECTION END
CHECK WHEEL SENSOR AND SENSOR ROTOR
Disconnect 12V battery negative terminal.
Disconnect rear left wheel sensor harness connector.
Remove dust and foreign matter adhered to the rear left wheel sensor and rear left sensor rotor with a vacuum dust collector through the rear left wheel sensor mounting hole.
GO TO 7.
CHECK WHEEL SENSOR
Check the rear left wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 11.
NO>>GO TO 8.
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect rear left wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to rear left wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 9.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the rear left wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 10.
NO>>GO TO 22.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-07” detected?
YES>>GO TO 22.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the rear left wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 14.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 12.
CHECK DATA MONITOR (2)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 13.
NO>>GO TO 14.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-07” detected?
YES>>GO TO 14.
NO>>INSPECTION END
CHECK TERMINAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Disconnect rear left wheel sensor harness connector.
Check the rear left wheel sensor terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 17.
NO>>Repair / replace harness, connector, or terminal. GO TO 15.
CHECK DATA MONITOR (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect rear left wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 16.
NO>>GO TO 17.
PERFORM SELF-DIAGNOSIS (4)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-07” detected?
YES>>GO TO 17.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect rear left wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and rear left wheel sensor harness connector.
ABS actuator and electric unit (control unit) — Continuity Connector Terminal B2 39, 23 Ground Not existed
Is the inspection result normal?
YES>>GO TO 18.
NO>>Repair / replace harness or connector. GO TO 18.
CHECK DATA MONITOR (4)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect rear left wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 19.
NO>>GO TO 20.
PERFORM SELF-DIAGNOSIS (5)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-07” detected?
YES>>GO TO 20.
NO>>INSPECTION END
REPLACE WHEEL SENSOR (2)
With CONSULT
Replace the rear left wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 21.
NO>>GO TO 22.
PERFORM SELF-DIAGNOSIS (6)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-07” detected?
YES>>GO TO 22.
NO>>INSPECTION END
REPLACE SENSOR ROTOR
With CONSULT
Replace the rear left sensor rotor. Refer to REAR SENSOR ROTOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-07” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C1065-09 Wheel Sensor Nissan Ariya 2026
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1065 | 09 | Rear left wheel sensor | Diagnosis condition |
|
|
| Signal (terminal) | Rear left wheel sensor signal | ||||
| Threshold | When a noise is detected in rear left wheel sensor. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-09" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK WHEEL HUB ASSEMBLY
Check that there is no excessive looseness in rear left wheel hub assembly. Refer to REAR WHEEL HUB : Periodic Maintenance Operation.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace the rear left wheel hub assembly. Refer to REAR WHEEL HUB : Removal & Installation. GO TO 2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
CHECK TIRE
Power switch OFF.
Check the rear left tire air pressure, wear and size. Refer to TIRE AIR PRESSURE : Service Data.
Is the inspection result normal?
YES>>GO TO 6.
NO>>Adjust air pressure or replace rear left tire. GO TO 4.
CHECK DATA MONITOR (1)
With CONSULT
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 5.
NO>>GO TO 6.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Never operate the vehicle.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-09” detected?
YES>>GO TO 6.
NO>>INSPECTION END
CHECK WHEEL SENSOR AND SENSOR ROTOR
Disconnect 12V battery negative terminal.
Disconnect rear left wheel sensor harness connector.
Remove dust and foreign matter adhered to the rear left wheel sensor and rear left sensor rotor with a vacuum dust collector through the rear left wheel sensor mounting hole.
GO TO 7.
CHECK WHEEL SENSOR
Check the rear left wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 11.
NO>>GO TO 8.
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect rear left wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to rear left wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 9.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the rear left wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 10.
NO>>GO TO 22.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-09” detected?
YES>>GO TO 22.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the rear left wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 14.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 12.
CHECK DATA MONITOR (2)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 13.
NO>>GO TO 14.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-09” detected?
YES>>GO TO 14.
NO>>INSPECTION END
CHECK TERMINAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Disconnect rear left wheel sensor harness connector.
Check the rear left wheel sensor terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 17.
NO>>Repair / replace harness, connector, or terminal. GO TO 15.
CHECK DATA MONITOR (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect rear left wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 16.
NO>>GO TO 17.
PERFORM SELF-DIAGNOSIS (4)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-09” detected?
YES>>GO TO 17.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect rear left wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and rear left wheel sensor harness connector.
ABS actuator and electric unit (control unit) — Continuity Connector Terminal B2 39, 23 Ground Not existed
Is the inspection result normal?
YES>>GO TO 18.
NO>>Repair / replace harness or connector. GO TO 18.
CHECK DATA MONITOR (4)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect rear left wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 19.
NO>>GO TO 20.
PERFORM SELF-DIAGNOSIS (5)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-09” detected?
YES>>GO TO 20.
NO>>INSPECTION END
REPLACE WHEEL SENSOR (2)
With CONSULT
Replace the rear left wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 21.
NO>>GO TO 22.
PERFORM SELF-DIAGNOSIS (6)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-09” detected?
YES>>GO TO 22.
NO>>INSPECTION END
REPLACE SENSOR ROTOR
With CONSULT
Replace the rear left sensor rotor. Refer to REAR SENSOR ROTOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-09” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C1065-11 Wheel Sensor Nissan Ariya 1st generation
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1065 | 11 | Rear left wheel sensor | Diagnosis condition |
|
|
| Signal (terminal) |
|
||||
| Threshold | When a short circuit is detected in rear left wheel sensor circuit. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-11" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK WHEEL SENSOR
Disconnect 12V battery negative terminal.
Check the rear left wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 3.
NO>>GO TO 2.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the rear left wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-11” detected?
YES>>GO TO 3.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the rear left wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 4.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-11” detected?
YES>>GO TO 5.
NO>>INSPECTION END
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 7.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect rear left wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-11” detected?
YES>>GO TO 7.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect rear left wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and rear left wheel sensor harness connector. (Check the continuity while turning steering wheel left and right, or while moving center harness in wheel housing.)
Measurement connector and terminal for power supply circuit
ABS actuator and electric unit (control unit) Rear left wheel sensor Continuity Connector Terminal Connector Terminal B2 39 B178 1 Existed Measurement connector and terminal for signal circuit
ABS actuator and electric unit (control unit) Rear left wheel sensor Continuity Connector Terminal Connector Terminal B2 23 B178 2 Existed
Is the inspection result normal?
YES>>GO TO 10.
NO>>Repair / replace harness or connector. GO TO 8.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect rear left wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-11” detected?
YES>>GO TO 9.
NO>>INSPECTION END
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect rear left wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to rear left wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 10.
REPLACE WHEEL SENSOR
Replace the rear left wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-11” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C1065-12 Wheel Sensor Nissan Ariya: FE0
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1065 | 12 | Rear left wheel sensor | Diagnosis condition |
|
|
| Signal (terminal) |
|
||||
| Threshold | When a short circuit is detected in rear left wheel sensor circuit. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-12" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK WHEEL SENSOR
Disconnect 12V battery negative terminal.
Check the rear left wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 3.
NO>>GO TO 2.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the rear left wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-12” detected?
YES>>GO TO 3.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the rear left wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 4.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-12” detected?
YES>>GO TO 5.
NO>>INSPECTION END
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 7.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect rear left wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-12” detected?
YES>>GO TO 7.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect rear left wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and rear left wheel sensor harness connector. (Check the continuity while turning steering wheel left and right, or while moving center harness in wheel housing.)
Measurement connector and terminal for power supply circuit
ABS actuator and electric unit (control unit) Rear left wheel sensor Continuity Connector Terminal Connector Terminal B2 39 B178 1 Existed Measurement connector and terminal for signal circuit
ABS actuator and electric unit (control unit) Rear left wheel sensor Continuity Connector Terminal Connector Terminal B2 23 B178 2 Existed
Is the inspection result normal?
YES>>GO TO 9.
NO>>Repair / replace harness or connector. GO TO 8.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect rear left wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-12” detected?
YES>>GO TO 9.
NO>>INSPECTION END
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect rear left wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to rear left wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 10.
REPLACE WHEEL SENSOR
Replace the rear left wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-12” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C1065-13 Wheel Sensor Nissan Ariya
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1065 | 13 | Rear left wheel sensor | Diagnosis condition |
|
|
| Signal (terminal) |
|
||||
| Threshold | When an open circuit is detected in rear left wheel sensor circuit. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-13" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK WHEEL SENSOR
Disconnect 12V battery negative terminal.
Check the rear left wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 3.
NO>>GO TO 2.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the rear left wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-13” detected?
YES>>GO TO 3.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the rear left wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 4.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-13” detected?
YES>>GO TO 5.
NO>>INSPECTION END
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 7.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect rear left wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-13” detected?
YES>>GO TO 7.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect rear left wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and rear left wheel sensor harness connector. (Check the continuity while turning steering wheel left and right, or while moving center harness in wheel housing.)
Measurement connector and terminal for power supply circuit
ABS actuator and electric unit (control unit) Rear left wheel sensor Continuity Connector Terminal Connector Terminal B2 39 B178 1 Existed Measurement connector and terminal for signal circuit
ABS actuator and electric unit (control unit) Rear left wheel sensor Continuity Connector Terminal Connector Terminal B2 23 B178 2 Existed
Is the inspection result normal?
YES>>GO TO 10.
NO>>Repair / replace harness or connector. GO TO 8.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect rear left wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-13” detected?
YES>>GO TO 9.
NO>>INSPECTION END
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect rear left wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to rear left wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 10.
REPLACE WHEEL SENSOR
Replace the rear left wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-13” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C1065-1c Wheel Sensor Nissan Ariya first Gen
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1065 | 1C | Rear left wheel sensor | Diagnosis condition |
|
|
| Signal (terminal) |
|
||||
| Threshold | When rear left wheel sensor power supply out of range. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-1C" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK WHEEL SENSOR
Disconnect 12V battery negative terminal.
Check the rear left wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 3.
NO>>GO TO 2.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the rear left wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-1C” detected?
YES>>GO TO 3.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the rear left wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 4.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-1C” detected?
YES>>GO TO 5.
NO>>INSPECTION END
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 7.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect rear left wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-1C” detected?
YES>>GO TO 7.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect rear left wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and rear left wheel sensor harness connector. (Check the continuity while turning steering wheel left and right, or while moving center harness in wheel housing.)
Measurement connector and terminal for power supply circuit
ABS actuator and electric unit (control unit) Rear left wheel sensor Continuity Connector Terminal Connector Terminal B2 39 B178 1 Existed Measurement connector and terminal for signal circuit
ABS actuator and electric unit (control unit) Rear left wheel sensor Continuity Connector Terminal Connector Terminal B2 23 B178 2 Existed
Is the inspection result normal?
YES>>GO TO 10.
NO>>Repair / replace harness or connector. GO TO 8.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect rear left wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-1C” detected?
YES>>GO TO 9.
NO>>INSPECTION END
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect rear left wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to rear left wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 10.
REPLACE WHEEL SENSOR
Replace the rear left wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-1C” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C1065-38 Wheel Sensor Nissan Ariya 1st generation
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1065 | 38 | Rear left wheel sensor | Diagnosis condition |
|
|
| Signal (terminal) | Rear left wheel sensor signal | ||||
| Threshold | When a malfunction is detected in rear left wheel sensor signal. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-38" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK WHEEL HUB ASSEMBLY
Check that there is no excessive looseness in rear left wheel hub assembly. Refer to REAR WHEEL HUB : Periodic Maintenance Operation.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace the rear left wheel hub assembly. Refer to REAR WHEEL HUB : Removal & Installation. GO TO 2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
CHECK TIRE
Power switch OFF.
Check the rear left tire air pressure, wear and size. Refer to TIRE AIR PRESSURE : Service Data.
Is the inspection result normal?
YES>>GO TO 6.
NO>>Adjust air pressure or replace rear left tire. GO TO 4.
CHECK DATA MONITOR (1)
With CONSULT
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 5.
NO>>GO TO 6.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Never operate the vehicle.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-38” detected?
YES>>GO TO 6.
NO>>INSPECTION END
CHECK WHEEL SENSOR AND SENSOR ROTOR
Disconnect 12V battery negative terminal.
Disconnect rear left wheel sensor harness connector.
Remove dust and foreign matter adhered to the rear left wheel sensor and rear left sensor rotor with a vacuum dust collector through the rear left wheel sensor mounting hole.
GO TO 7.
CHECK WHEEL SENSOR
Check the rear left wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 11.
NO>>GO TO 8.
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect rear left wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to rear left wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 9.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the rear left wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 10.
NO>>GO TO 22.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-38” detected?
YES>>GO TO 22.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the rear left wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 14.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 12.
CHECK DATA MONITOR (2)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 13.
NO>>GO TO 14.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-38” detected?
YES>>GO TO 14.
NO>>INSPECTION END
CHECK TERMINAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Disconnect rear left wheel sensor harness connector.
Check the rear left wheel sensor terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 17.
NO>>Repair / replace harness, connector, or terminal. GO TO 15.
CHECK DATA MONITOR (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect rear left wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 16.
NO>>GO TO 17.
PERFORM SELF-DIAGNOSIS (4)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-38” detected?
YES>>GO TO 17.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect rear left wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and rear left wheel sensor harness connector.
ABS actuator and electric unit (control unit) — Continuity Connector Terminal B2 39, 23 Ground Not existed
Is the inspection result normal?
YES>>GO TO 18.
NO>>Repair / replace harness or connector. GO TO 18.
CHECK DATA MONITOR (4)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect rear left wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 19.
NO>>GO TO 20.
PERFORM SELF-DIAGNOSIS (5)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-38” detected?
YES>>GO TO 20.
NO>>INSPECTION END
REPLACE WHEEL SENSOR (2)
With CONSULT
Replace the rear left wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 21.
NO>>GO TO 22.
PERFORM SELF-DIAGNOSIS (6)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-38” detected?
YES>>GO TO 22.
NO>>INSPECTION END
REPLACE SENSOR ROTOR
With CONSULT
Replace the rear left sensor rotor. Refer to REAR SENSOR ROTOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-38” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C1065-4a Wheel Sensor Nissan Ariya SUV
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1065 | 4A | Rear left wheel sensor | Diagnosis condition |
|
|
| Signal (terminal) |
|
||||
| Threshold | When rear left wheel sensor is installed to wrong position. | ||||
| Diagnosis delay time | 3 seconds or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-4A" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK SELF-DIAGNOSIS RESULT
With CONSULT
Check the self-diagnosis result for "ABS".
Is the display result "C1065-4A" of “CRNT”?
YES>>GO TO 2.
NO>>Erase self-diagnosis result for “ABS”.
REPLACE WHEEL SENSOR (1)
Replace the rear left wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is the display result "C1065-4A" of “CRNT”?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>Erase self-diagnosis result for “ABS”.
C1065-64 Wheel Sensor Nissan Ariya
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1065 | 64 | Rear left wheel sensor | Diagnosis condition |
|
|
| Signal (terminal) | Rear left wheel sensor signal | ||||
| Threshold | When difference between rear left wheel and other rear left wheel speed is detected the Nissan Ariya vehicle is driven, because of installation of other tires than specified. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-64" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK WHEEL HUB ASSEMBLY
Check that there is no excessive looseness in rear left wheel hub assembly. Refer to REAR WHEEL HUB : Periodic Maintenance Operation.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace the rear left wheel hub assembly. Refer to REAR WHEEL HUB : Removal & Installation. GO TO 2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
CHECK TIRE
Power switch OFF.
Check the rear left tire air pressure, wear and size. Refer to TIRE AIR PRESSURE : Service Data.
Is the inspection result normal?
YES>>GO TO 6.
NO>>Adjust air pressure or replace rear left tire. GO TO 4.
CHECK DATA MONITOR (1)
With CONSULT
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 5.
NO>>GO TO 6.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Never operate the vehicle.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-64” detected?
YES>>GO TO 6.
NO>>INSPECTION END
CHECK WHEEL SENSOR AND SENSOR ROTOR
Disconnect 12V battery negative terminal.
Disconnect rear left wheel sensor harness connector.
Remove dust and foreign matter adhered to the rear left wheel sensor and rear left sensor rotor with a vacuum dust collector through the rear left wheel sensor mounting hole.
GO TO 7.
CHECK WHEEL SENSOR
Check the rear left wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 11.
NO>>GO TO 8.
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect rear left wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to rear left wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 9.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the rear left wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 10.
NO>>GO TO 22.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-64” detected?
YES>>GO TO 22.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the rear left wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 14.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 12.
CHECK DATA MONITOR (2)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 13.
NO>>GO TO 14.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-64” detected?
YES>>GO TO 14.
NO>>INSPECTION END
CHECK TERMINAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Disconnect rear left wheel sensor harness connector.
Check the rear left wheel sensor terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 17.
NO>>Repair / replace harness, connector, or terminal. GO TO 15.
CHECK DATA MONITOR (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect rear left wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 16.
NO>>GO TO 17.
PERFORM SELF-DIAGNOSIS (4)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-64” detected?
YES>>GO TO 17.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect rear left wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and rear left wheel sensor harness connector.
ABS actuator and electric unit (control unit) — Continuity Connector Terminal B2 39, 23 Ground Not existed
Is the inspection result normal?
YES>>GO TO 18.
NO>>Repair / replace harness or connector. GO TO 18.
CHECK DATA MONITOR (4)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect rear left wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 19.
NO>>GO TO 20.
PERFORM SELF-DIAGNOSIS (5)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-64” detected?
YES>>GO TO 20.
NO>>INSPECTION END
REPLACE WHEEL SENSOR (2)
With CONSULT
Replace the rear left wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 21.
NO>>GO TO 22.
PERFORM SELF-DIAGNOSIS (6)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-64” detected?
YES>>GO TO 22.
NO>>INSPECTION END
REPLACE SENSOR ROTOR
With CONSULT
Replace the rear left sensor rotor. Refer to REAR SENSOR ROTOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-64” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C1065-92 Wheel Sensor Nissan Ariya: FE0
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1065 | 92 | Rear left wheel sensor | Diagnosis condition |
|
|
| Signal (terminal) | Rear left wheel sensor signal | ||||
| Threshold | When a malfunction is detected in rear left wheel sensor signal. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-92" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK WHEEL HUB ASSEMBLY
Check that there is no excessive looseness in rear left wheel hub assembly. Refer to REAR WHEEL HUB : Periodic Maintenance Operation.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace the rear left wheel hub assembly. Refer to REAR WHEEL HUB : Removal & Installation. GO TO 2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
CHECK TIRE
Power switch OFF.
Check the rear left tire air pressure, wear and size. Refer to TIRE AIR PRESSURE : Service Data.
Is the inspection result normal?
YES>>GO TO 6.
NO>>Adjust air pressure or replace rear left tire. GO TO 4.
CHECK DATA MONITOR (1)
With CONSULT
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 5.
NO>>GO TO 6.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Never operate the vehicle.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-92” detected?
YES>>GO TO 6.
NO>>INSPECTION END
CHECK WHEEL SENSOR AND SENSOR ROTOR
Disconnect 12V battery negative terminal.
Disconnect rear left wheel sensor harness connector.
Remove dust and foreign matter adhered to the rear left wheel sensor and rear left sensor rotor with a vacuum dust collector through the rear left wheel sensor mounting hole.
GO TO 7.
CHECK WHEEL SENSOR
Check the rear left wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 11.
NO>>GO TO 8.
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect rear left wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to rear left wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 9.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the rear left wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 10.
NO>>GO TO 22.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-92” detected?
YES>>GO TO 22.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the rear left wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 14.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 12.
CHECK DATA MONITOR (2)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 13.
NO>>GO TO 14.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-92” detected?
YES>>GO TO 14.
NO>>INSPECTION END
CHECK TERMINAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Disconnect rear left wheel sensor harness connector.
Check the rear left wheel sensor terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 17.
NO>>Repair / replace harness, connector, or terminal. GO TO 15.
CHECK DATA MONITOR (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect rear left wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 16.
NO>>GO TO 17.
PERFORM SELF-DIAGNOSIS (4)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-92” detected?
YES>>GO TO 17.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect rear left wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and rear left wheel sensor harness connector.
ABS actuator and electric unit (control unit) — Continuity Connector Terminal B2 39, 23 Ground Not existed
Is the inspection result normal?
YES>>GO TO 18.
NO>>Repair / replace harness or connector. GO TO 18.
CHECK DATA MONITOR (4)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect rear left wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 19.
NO>>GO TO 20.
PERFORM SELF-DIAGNOSIS (5)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-92” detected?
YES>>GO TO 20.
NO>>INSPECTION END
REPLACE WHEEL SENSOR (2)
With CONSULT
Replace the rear left wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 21.
NO>>GO TO 22.
PERFORM SELF-DIAGNOSIS (6)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-92” detected?
YES>>GO TO 22.
NO>>INSPECTION END
REPLACE SENSOR ROTOR
With CONSULT
Replace the rear left sensor rotor. Refer to REAR SENSOR ROTOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1065-92” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C1067-02 Wheel Sensor Nissan Ariya SUV
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1067 | 02 | Rear right wheel sensor | Diagnosis condition |
|
|
| Signal (terminal) |
|
||||
| Threshold | When a malfunction is detected in rear right wheel sensor. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-02" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK WHEEL SENSOR
Disconnect 12V battery negative terminal.
Check the rear right wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 3.
NO>>GO TO 2.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the rear right wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-02” detected?
YES>>GO TO 3.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the rear right wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 4.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-02” detected?
YES>>GO TO 5.
NO>>INSPECTION END
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 7.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect rear right wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-02” detected?
YES>>GO TO 7.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect rear right wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and rear right wheel sensor harness connector. (Check the continuity while turning steering wheel right and right, or while moving center harness in wheel housing.)
Measurement connector and terminal for power supply circuit
ABS actuator and electric unit (control unit) Rear right wheel sensor Continuity Connector Terminal Connector Terminal B2 22 B180 1 Existed Measurement connector and terminal for signal circuit
ABS actuator and electric unit (control unit) Rear right wheel sensor Continuity Connector Terminal Connector Terminal B2 37 B180 2 Existed
Is the inspection result normal?
YES>>GO TO 9.
NO>>Repair / replace harness or connector. GO TO 8.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect rear right wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-02” detected?
YES>>GO TO 9.
NO>>INSPECTION END
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect rear right wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to rear right wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 10.
REPLACE WHEEL SENSOR
Replace the rear right wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-02” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C1067-07 Wheel Sensor Nissan Ariya first Gen
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | ||||
|---|---|---|---|---|---|---|
| C1067 | 07 | Rear right wheel sensor | 1 | Diagnosis condition |
|
|
| Signal (terminal) | Rear right wheel sensor signal | |||||
| Threshold | When distance between rear right wheel sensor and rear right wheel sensor rotor is large. | |||||
| Diagnosis delay time | 1 - 60 seconds or more | |||||
| 2 | Diagnosis condition |
|
||||
| Signal (terminal) | Rear right wheel sensor signal | |||||
| Threshold | When installation of rear right wheel sensor is not normal. | |||||
| Diagnosis delay time | 1 - 60 seconds or more | |||||
| 3 | Diagnosis condition |
|
||||
| Signal (terminal) | Rear right wheel sensor signal | |||||
| Threshold | When installation of rear right sensor rotor is not normal. | |||||
| Diagnosis delay time | 1 - 60 seconds or more | |||||
| 4 | Diagnosis condition |
|
||||
| Signal (terminal) | Rear right wheel sensor signal | |||||
| Threshold | When there is contamination on to the rear right wheel sensor. | |||||
| Diagnosis delay time | 1 - 60 seconds or more | |||||
| 5 | Diagnosis condition |
|
||||
| Signal (terminal) | Rear right wheel sensor signal | |||||
| Threshold | When there is contamination on to the rear right sensor rotor. | |||||
| Diagnosis delay time | 1 - 60 seconds or more | |||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-07" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK WHEEL HUB ASSEMBLY
Check that there is no excessive looseness in rear right wheel hub assembly. Refer to REAR WHEEL HUB : Periodic Maintenance Operation.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace the rear right wheel hub assembly. Refer to REAR WHEEL HUB : Removal & Installation. GO TO 2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
CHECK TIRE
Power switch OFF.
Check the rear right tire air pressure, wear and size. Refer to TIRE AIR PRESSURE : Service Data.
Is the inspection result normal?
YES>>GO TO 6.
NO>>Adjust air pressure or replace rear right tire. GO TO 4.
CHECK DATA MONITOR (1)
With CONSULT
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 5.
NO>>GO TO 6.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-07” detected?
YES>>GO TO 6.
NO>>INSPECTION END
CHECK WHEEL SENSOR AND SENSOR ROTOR
Disconnect 12V battery negative terminal.
Disconnect rear right wheel sensor harness connector.
Remove dust and foreign matter adhered to the rear right wheel sensor and rear right sensor rotor with a vacuum dust collector through the rear right wheel sensor mounting hole.
GO TO 7.
CHECK WHEEL SENSOR
Check the rear right wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 11.
NO>>GO TO 8.
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect rear right wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to rear right wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 9.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the rear right wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 10.
NO>>GO TO 22.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-07” detected?
YES>>GO TO 22.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the rear right wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 14.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 12.
CHECK DATA MONITOR (2)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 13.
NO>>GO TO 14.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-07” detected?
YES>>GO TO 14.
NO>>INSPECTION END
CHECK TERMINAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Disconnect rear right wheel sensor harness connector.
Check the rear right wheel sensor terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 17.
NO>>Repair / replace harness, connector, or terminal. GO TO 15.
CHECK DATA MONITOR (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect rear right wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 16.
NO>>GO TO 17.
PERFORM SELF-DIAGNOSIS (4)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-07” detected?
YES>>GO TO 17.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect rear right wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and rear right wheel sensor harness connector.
ABS actuator and electric unit (control unit) — Continuity Connector Terminal B2 22, 37 Ground Not existed
Is the inspection result normal?
YES>>GO TO 18.
NO>>Repair / replace harness or connector. GO TO 18.
CHECK DATA MONITOR (4)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect rear right wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 19.
NO>>GO TO 20.
PERFORM SELF-DIAGNOSIS (5)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-07” detected?
YES>>GO TO 20.
NO>>INSPECTION END
REPLACE WHEEL SENSOR (2)
With CONSULT
Replace the rear right wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 21.
NO>>GO TO 22.
PERFORM SELF-DIAGNOSIS (6)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-07” detected?
YES>>GO TO 22.
NO>>INSPECTION END
REPLACE SENSOR ROTOR
With CONSULT
Replace the rear right sensor rotor. Refer to REAR SENSOR ROTOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-07” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C1067-09 Wheel Sensor Nissan Ariya first Gen
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1067 | 09 | Rear right wheel sensor | Diagnosis condition |
|
|
| Signal (terminal) | Rear right wheel sensor signal | ||||
| Threshold | When a noise is detected in rear right wheel sensor. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-09" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK WHEEL HUB ASSEMBLY
Check that there is no excessive looseness in rear right wheel hub assembly. Refer to REAR WHEEL HUB : Periodic Maintenance Operation.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace the rear right wheel hub assembly. Refer to REAR WHEEL HUB : Removal & Installation. GO TO 2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
CHECK TIRE
Power switch OFF.
Check the rear right tire air pressure, wear and size. Refer to TIRE AIR PRESSURE : Service Data.
Is the inspection result normal?
YES>>GO TO 6.
NO>>Adjust air pressure or replace rear right tire. GO TO 4.
CHECK DATA MONITOR (1)
With CONSULT
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 5.
NO>>GO TO 6.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-09” detected?
YES>>GO TO 6.
NO>>INSPECTION END
CHECK WHEEL SENSOR AND SENSOR ROTOR
Disconnect 12V battery negative terminal.
Disconnect rear right wheel sensor harness connector.
Remove dust and foreign matter adhered to the rear right wheel sensor and rear right sensor rotor with a vacuum dust collector through the rear right wheel sensor mounting hole.
GO TO 7.
CHECK WHEEL SENSOR
Check the rear right wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 11.
NO>>GO TO 8.
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect rear right wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to rear right wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 9.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the rear right wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 10.
NO>>GO TO 22.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-09” detected?
YES>>GO TO 22.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the rear right wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 14.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 12.
CHECK DATA MONITOR (2)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 13.
NO>>GO TO 14.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-09” detected?
YES>>GO TO 14.
NO>>INSPECTION END
CHECK TERMINAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Disconnect rear right wheel sensor harness connector.
Check the rear right wheel sensor terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 17.
NO>>Repair / replace harness, connector, or terminal. GO TO 15.
CHECK DATA MONITOR (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect rear right wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 16.
NO>>GO TO 17.
PERFORM SELF-DIAGNOSIS (4)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-09” detected?
YES>>GO TO 17.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect rear right wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and rear right wheel sensor harness connector.
ABS actuator and electric unit (control unit) — Continuity Connector Terminal B2 22, 37 Ground Not existed
Is the inspection result normal?
YES>>GO TO 18.
NO>>Repair / replace harness or connector. GO TO 18.
CHECK DATA MONITOR (4)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect rear right wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 19.
NO>>GO TO 20.
PERFORM SELF-DIAGNOSIS (5)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-09” detected?
YES>>GO TO 20.
NO>>INSPECTION END
REPLACE WHEEL SENSOR (2)
With CONSULT
Replace the rear right wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 21.
NO>>GO TO 22.
PERFORM SELF-DIAGNOSIS (6)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-09” detected?
YES>>GO TO 22.
NO>>INSPECTION END
REPLACE SENSOR ROTOR
With CONSULT
Replace the rear right sensor rotor. Refer to REAR SENSOR ROTOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-09” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C1067-11 Wheel Sensor Nissan Ariya: FE0
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1067 | 11 | Rear right wheel sensor | Diagnosis condition |
|
|
| Signal (terminal) |
|
||||
| Threshold | When a short circuit is detected in rear right wheel sensor circuit. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-11" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK WHEEL SENSOR
Disconnect 12V battery negative terminal.
Check the rear right wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 3.
NO>>GO TO 2.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the rear right wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-11” detected?
YES>>GO TO 3.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the rear right wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 4.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-11” detected?
YES>>GO TO 5.
NO>>INSPECTION END
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 7.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect rear right wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-11” detected?
YES>>GO TO 7.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect rear right wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and rear right wheel sensor harness connector. (Check the continuity while turning steering wheel right and right, or while moving center harness in wheel housing.)
Measurement connector and terminal for power supply circuit
ABS actuator and electric unit (control unit) Rear right wheel sensor Continuity Connector Terminal Connector Terminal B2 22 B180 1 Existed Measurement connector and terminal for signal circuit
ABS actuator and electric unit (control unit) Rear right wheel sensor Continuity Connector Terminal Connector Terminal B2 37 B180 2 Existed
Is the inspection result normal?
YES>>GO TO 10.
NO>>Repair / replace harness or connector. GO TO 8.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect rear right wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-11” detected?
YES>>GO TO 9.
NO>>INSPECTION END
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect rear right wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to rear right wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 10.
REPLACE WHEEL SENSOR
Replace the rear right wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-11” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C1067-12 Wheel Sensor Nissan Ariya
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1067 | 12 | Rear right wheel sensor | Diagnosis condition |
|
|
| Signal (terminal) |
|
||||
| Threshold | When a short circuit is detected in rear right wheel sensor circuit. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-12" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK WHEEL SENSOR
Disconnect 12V battery negative terminal.
Check the rear right wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 3.
NO>>GO TO 2.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the rear right wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-12” detected?
YES>>GO TO 3.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the rear right wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 4.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-12” detected?
YES>>GO TO 5.
NO>>INSPECTION END
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 7.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect rear right wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-12” detected?
YES>>GO TO 7.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect rear right wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and rear right wheel sensor harness connector. (Check the continuity while turning steering wheel right and right, or while moving center harness in wheel housing.)
Measurement connector and terminal for power supply circuit
ABS actuator and electric unit (control unit) Rear right wheel sensor Continuity Connector Terminal Connector Terminal B2 22 B180 1 Existed Measurement connector and terminal for signal circuit
ABS actuator and electric unit (control unit) Rear right wheel sensor Continuity Connector Terminal Connector Terminal B2 37 B180 2 Existed
Is the inspection result normal?
YES>>GO TO 10.
NO>>Repair / replace harness or connector. GO TO 8.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect rear right wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-12” detected?
YES>>GO TO 9.
NO>>INSPECTION END
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect rear right wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to rear right wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 10.
REPLACE WHEEL SENSOR
Replace the rear right wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-12” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C1067-13 Wheel Sensor Nissan Ariya 2026
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1067 | 13 | Rear right wheel sensor | Diagnosis condition |
|
|
| Signal (terminal) |
|
||||
| Threshold | When an open circuit is detected in rear right wheel sensor circuit. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-13" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK WHEEL SENSOR
Disconnect 12V battery negative terminal.
Check the rear right wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 3.
NO>>GO TO 2.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the rear right wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-13” detected?
YES>>GO TO 3.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the rear right wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 4.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-13” detected?
YES>>GO TO 5.
NO>>INSPECTION END
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 7.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect rear right wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-13” detected?
YES>>GO TO 7.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect rear right wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and rear right wheel sensor harness connector. (Check the continuity while turning steering wheel right and right, or while moving center harness in wheel housing.)
Measurement connector and terminal for power supply circuit
ABS actuator and electric unit (control unit) Rear right wheel sensor Continuity Connector Terminal Connector Terminal B2 22 B180 1 Existed Measurement connector and terminal for signal circuit
ABS actuator and electric unit (control unit) Rear right wheel sensor Continuity Connector Terminal Connector Terminal B2 37 B180 2 Existed
Is the inspection result normal?
YES>>GO TO 10.
NO>>Repair / replace harness or connector. GO TO 8.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect rear right wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-13” detected?
YES>>GO TO 9.
NO>>INSPECTION END
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect rear right wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to rear right wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 10.
REPLACE WHEEL SENSOR
Replace the rear right wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-13” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C1067-1c Wheel Sensor Nissan Ariya 2026
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1067 | 1C | Rear right wheel sensor | Diagnosis condition |
|
|
| Signal (terminal) |
|
||||
| Threshold | When rear right wheel sensor power supply out of range. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-1C" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK WHEEL SENSOR
Disconnect 12V battery negative terminal.
Check the rear right wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 3.
NO>>GO TO 2.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the rear right wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-1C” detected?
YES>>GO TO 3.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the rear right wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 4.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-1C” detected?
YES>>GO TO 5.
NO>>INSPECTION END
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 7.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect rear right wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-1C” detected?
YES>>GO TO 7.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect rear right wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and rear right wheel sensor harness connector. (Check the continuity while turning steering wheel right and right, or while moving center harness in wheel housing.)
Measurement connector and terminal for power supply circuit
ABS actuator and electric unit (control unit) Rear right wheel sensor Continuity Connector Terminal Connector Terminal B2 22 B180 1 Existed Measurement connector and terminal for signal circuit
ABS actuator and electric unit (control unit) Rear right wheel sensor Continuity Connector Terminal Connector Terminal B2 37 B180 2 Existed
Is the inspection result normal?
YES>>GO TO 10.
NO>>Repair / replace harness or connector. GO TO 8.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect rear right wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-1C” detected?
YES>>GO TO 9.
NO>>INSPECTION END
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect rear right wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to rear right wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 10.
REPLACE WHEEL SENSOR
Replace the rear right wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-1C” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C1067-38 Wheel Sensor Nissan Ariya 1st generation
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1067 | 38 | Rear right wheel sensor | Diagnosis condition |
|
|
| Signal (terminal) | Rear right wheel sensor signal | ||||
| Threshold | When a malfunction is detected in rear right wheel sensor signal. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-38" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK WHEEL HUB ASSEMBLY
Check that there is no excessive looseness in rear right wheel hub assembly. Refer to REAR WHEEL HUB : Periodic Maintenance Operation.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace the rear right wheel hub assembly. Refer to REAR WHEEL HUB : Removal & Installation. GO TO 2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
CHECK TIRE
Power switch OFF.
Check the rear right tire air pressure, wear and size. Refer to TIRE AIR PRESSURE : Service Data.
Is the inspection result normal?
YES>>GO TO 6.
NO>>Adjust air pressure or replace rear right tire. GO TO 4.
CHECK DATA MONITOR (1)
With CONSULT
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 5.
NO>>GO TO 6.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-38” detected?
YES>>GO TO 6.
NO>>INSPECTION END
CHECK WHEEL SENSOR AND SENSOR ROTOR
Disconnect 12V battery negative terminal.
Disconnect rear right wheel sensor harness connector.
Remove dust and foreign matter adhered to the rear right wheel sensor and rear right sensor rotor with a vacuum dust collector through the rear right wheel sensor mounting hole.
GO TO 7.
CHECK WHEEL SENSOR
Check the rear right wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 11.
NO>>GO TO 8.
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect rear right wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to rear right wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 9.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the rear right wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 10.
NO>>GO TO 22.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-38” detected?
YES>>GO TO 22.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the rear right wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 14.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 12.
CHECK DATA MONITOR (2)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 13.
NO>>GO TO 14.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-38” detected?
YES>>GO TO 14.
NO>>INSPECTION END
CHECK TERMINAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Disconnect rear right wheel sensor harness connector.
Check the rear right wheel sensor terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 17.
NO>>Repair / replace harness, connector, or terminal. GO TO 15.
CHECK DATA MONITOR (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect rear right wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 16.
NO>>GO TO 17.
PERFORM SELF-DIAGNOSIS (4)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-38” detected?
YES>>GO TO 17.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect rear right wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and rear right wheel sensor harness connector.
ABS actuator and electric unit (control unit) — Continuity Connector Terminal B2 22, 37 Ground Not existed
Is the inspection result normal?
YES>>GO TO 18.
NO>>Repair / replace harness or connector. GO TO 18.
CHECK DATA MONITOR (4)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect rear right wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 19.
NO>>GO TO 20.
PERFORM SELF-DIAGNOSIS (5)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-38” detected?
YES>>GO TO 20.
NO>>INSPECTION END
REPLACE WHEEL SENSOR (2)
With CONSULT
Replace the rear right wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 21.
NO>>GO TO 22.
PERFORM SELF-DIAGNOSIS (6)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-38” detected?
YES>>GO TO 22.
NO>>INSPECTION END
REPLACE SENSOR ROTOR
With CONSULT
Replace the rear right sensor rotor. Refer to REAR SENSOR ROTOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-38” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C1067-4a Wheel Sensor Nissan Ariya SUV
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1067 | 4A | Rear right wheel sensor | Diagnosis condition |
|
|
| Signal (terminal) |
|
||||
| Threshold | When rear right wheel sensor is installed to wrong position. | ||||
| Diagnosis delay time | 3 seconds or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-4A" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK SELF-DIAGNOSIS RESULT
With CONSULT
Check the self-diagnosis result for "ABS".
Is the display result "C1067-4A" of “CRNT”?
YES>>GO TO 2.
NO>>Erase self-diagnosis result for “ABS”.
REPLACE WHEEL SENSOR (1)
Replace the rear right wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is the display result "C1067-4A" of “CRNT”?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>Erase self-diagnosis result for “ABS”.
C1067-64 Wheel Sensor Nissan Ariya first Gen
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1067 | 64 | Rear right wheel sensor | Diagnosis condition |
|
|
| Signal (terminal) | Rear right wheel sensor signal | ||||
| Threshold | When difference between rear right wheel and other rear right wheel speed is detected the Nissan Ariya vehicle is driven, because of installation of other tires than specified. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-64" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK WHEEL HUB ASSEMBLY
Check that there is no excessive looseness in rear right wheel hub assembly. Refer to REAR WHEEL HUB : Periodic Maintenance Operation.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace the rear right wheel hub assembly. Refer to REAR WHEEL HUB : Removal & Installation. GO TO 2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
CHECK TIRE
Power switch OFF.
Check the rear right tire air pressure, wear and size. Refer to TIRE AIR PRESSURE : Service Data.
Is the inspection result normal?
YES>>GO TO 6.
NO>>Adjust air pressure or replace rear right tire. GO TO 4.
CHECK DATA MONITOR (1)
With CONSULT
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 5.
NO>>GO TO 6.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-64” detected?
YES>>GO TO 6.
NO>>INSPECTION END
CHECK WHEEL SENSOR AND SENSOR ROTOR
Disconnect 12V battery negative terminal.
Disconnect rear right wheel sensor harness connector.
Remove dust and foreign matter adhered to the rear right wheel sensor and rear right sensor rotor with a vacuum dust collector through the rear right wheel sensor mounting hole.
GO TO 7.
CHECK WHEEL SENSOR
Check the rear right wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 11.
NO>>GO TO 8.
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect rear right wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to rear right wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 9.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the rear right wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 10.
NO>>GO TO 22.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-64” detected?
YES>>GO TO 22.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the rear right wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 14.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 12.
CHECK DATA MONITOR (2)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 13.
NO>>GO TO 14.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-64” detected?
YES>>GO TO 14.
NO>>INSPECTION END
CHECK TERMINAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Disconnect rear right wheel sensor harness connector.
Check the rear right wheel sensor terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 17.
NO>>Repair / replace harness, connector, or terminal. GO TO 15.
CHECK DATA MONITOR (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect rear right wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 16.
NO>>GO TO 17.
PERFORM SELF-DIAGNOSIS (4)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-64” detected?
YES>>GO TO 17.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect rear right wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and rear right wheel sensor harness connector.
ABS actuator and electric unit (control unit) — Continuity Connector Terminal B2 22, 37 Ground Not existed
Is the inspection result normal?
YES>>GO TO 18.
NO>>Repair / replace harness or connector. GO TO 18.
CHECK DATA MONITOR (4)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect rear right wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 19.
NO>>GO TO 20.
PERFORM SELF-DIAGNOSIS (5)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-64” detected?
YES>>GO TO 20.
NO>>INSPECTION END
REPLACE WHEEL SENSOR (2)
With CONSULT
Replace the rear right wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 21.
NO>>GO TO 22.
PERFORM SELF-DIAGNOSIS (6)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-64” detected?
YES>>GO TO 22.
NO>>INSPECTION END
REPLACE SENSOR ROTOR
With CONSULT
Replace the rear right sensor rotor. Refer to REAR SENSOR ROTOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-64” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C1067-92 Wheel Sensor Nissan Ariya
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1067 | 92 | Rear right wheel sensor | Diagnosis condition |
|
|
| Signal (terminal) | Rear right wheel sensor signal | ||||
| Threshold | When a malfunction is detected in rear right wheel sensor signal. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-92" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK WHEEL HUB ASSEMBLY
Check that there is no excessive looseness in rear right wheel hub assembly. Refer to REAR WHEEL HUB : Periodic Maintenance Operation.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace the rear right wheel hub assembly. Refer to REAR WHEEL HUB : Removal & Installation. GO TO 2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
CHECK TIRE
Power switch OFF.
Check the rear right tire air pressure, wear and size. Refer to TIRE AIR PRESSURE : Service Data.
Is the inspection result normal?
YES>>GO TO 6.
NO>>Adjust air pressure or replace rear right tire. GO TO 4.
CHECK DATA MONITOR (1)
With CONSULT
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 5.
NO>>GO TO 6.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-92” detected?
YES>>GO TO 6.
NO>>INSPECTION END
CHECK WHEEL SENSOR AND SENSOR ROTOR
Disconnect 12V battery negative terminal.
Disconnect rear right wheel sensor harness connector.
Remove dust and foreign matter adhered to the rear right wheel sensor and rear right sensor rotor with a vacuum dust collector through the rear right wheel sensor mounting hole.
GO TO 7.
CHECK WHEEL SENSOR
Check the rear right wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 11.
NO>>GO TO 8.
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect rear right wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to rear right wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 9.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the rear right wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 10.
NO>>GO TO 22.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-92” detected?
YES>>GO TO 22.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the rear right wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 14.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 12.
CHECK DATA MONITOR (2)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 13.
NO>>GO TO 14.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-92” detected?
YES>>GO TO 14.
NO>>INSPECTION END
CHECK TERMINAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Disconnect rear right wheel sensor harness connector.
Check the rear right wheel sensor terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 17.
NO>>Repair / replace harness, connector, or terminal. GO TO 15.
CHECK DATA MONITOR (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect rear right wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 16.
NO>>GO TO 17.
PERFORM SELF-DIAGNOSIS (4)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-92” detected?
YES>>GO TO 17.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect rear right wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and rear right wheel sensor harness connector.
ABS actuator and electric unit (control unit) — Continuity Connector Terminal B2 22, 37 Ground Not existed
Is the inspection result normal?
YES>>GO TO 18.
NO>>Repair / replace harness or connector. GO TO 18.
CHECK DATA MONITOR (4)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect rear right wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 19.
NO>>GO TO 20.
PERFORM SELF-DIAGNOSIS (5)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-92” detected?
YES>>GO TO 20.
NO>>INSPECTION END
REPLACE WHEEL SENSOR (2)
With CONSULT
Replace the rear right wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 21.
NO>>GO TO 22.
PERFORM SELF-DIAGNOSIS (6)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-92” detected?
YES>>GO TO 22.
NO>>INSPECTION END
REPLACE SENSOR ROTOR
With CONSULT
Replace the rear right sensor rotor. Refer to REAR SENSOR ROTOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-92” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C1068-95 Wheel Sensor Nissan Ariya: FE0
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | ||||
|---|---|---|---|---|---|---|
| C1068 | 95 | Front wheel sensor | 1 | Diagnosis condition |
|
|
| Signal (terminal) | Front left wheel sensor signal | |||||
| Threshold | When a malfunction is detected in front left wheel sensor. | |||||
| Diagnosis delay time | 1 second or less | |||||
| 2 | Diagnosis condition |
|
||||
| Signal (terminal) | Front right wheel sensor signal | |||||
| Threshold | When a malfunction is detected in front right wheel sensor. | |||||
| Diagnosis delay time | 1 second or less | |||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1068-95" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK WHEEL HUB ASSEMBLY
Check that there is no excessive looseness in front wheel hub assembly. Refer to FRONT WHEEL HUB AND KNUCKLE : Periodic Maintenance Operation.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace the front wheel hub assembly. Refer to FRONT WHEEL HUB AND KNUCKLE : Removal & Installation. GO TO 2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
CHECK TIRE
Power switch OFF.
Check the front tire air pressure, wear and size. Refer to TIRE AIR PRESSURE : Service Data.
Is the inspection result normal?
YES>>GO TO 6.
NO>>Adjust air pressure or replace front tire. GO TO 4.
CHECK DATA MONITOR (1)
With CONSULT
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 5.
NO>>GO TO 6.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1068-95” detected?
YES>>GO TO 6.
NO>>INSPECTION END
CHECK WHEEL SENSOR AND SENSOR ROTOR
Disconnect 12V battery negative terminal.
Disconnect front wheel sensor harness connector.
Remove dust and foreign matter adhered to the front wheel sensor and front sensor rotor with a vacuum dust collector through the front wheel sensor mounting hole.
GO TO 7.
CHECK WHEEL SENSOR
Check the front wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 11.
NO>>GO TO 8.
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect front wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to front wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 9.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the front wheel sensor. Refer to FRONT WHEEL SENSOR : Removal & Installation.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 10.
NO>>GO TO 22.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1068-95” detected?
YES>>GO TO 22.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the front wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 14.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 12.
CHECK DATA MONITOR (2)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 13.
NO>>GO TO 14.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1068-95” detected?
YES>>GO TO 14.
NO>>INSPECTION END
CHECK TERMINAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Disconnect front wheel sensor harness connector.
Check the front wheel sensor terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 17.
NO>>Repair / replace harness, connector, or terminal. GO TO 15.
CHECK DATA MONITOR (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect front wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 16.
NO>>GO TO 17.
PERFORM SELF-DIAGNOSIS (4)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1068-95” detected?
YES>>GO TO 17.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect front wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and front wheel sensor harness connector.
ABS actuator and electric unit (control unit) — Continuity Connector Terminal B2 24, 7 (Left) Ground Not existed 21, 26 (Right)
Is the inspection result normal?
YES>>GO TO 18.
NO>>Repair / replace harness or connector. GO TO 18.
CHECK DATA MONITOR (4)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect front wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 19.
NO>>GO TO 20.
PERFORM SELF-DIAGNOSIS (5)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1068-95” detected?
YES>>GO TO 20.
NO>>INSPECTION END
REPLACE WHEEL SENSOR (2)
With CONSULT
Replace the front wheel sensor. Refer to FRONT WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 21.
NO>>GO TO 22.
PERFORM SELF-DIAGNOSIS (6)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1068-95” detected?
YES>>GO TO 22.
NO>>INSPECTION END
REPLACE SENSOR ROTOR
With CONSULT
Replace the front sensor rotor. Refer to FRONT SENSOR ROTOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1068-95” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C1068-96 Wheel Sensor Nissan Ariya: FE0
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | ||||
|---|---|---|---|---|---|---|
| C1068 | 96 | Front wheel sensor | 1 | Diagnosis condition |
|
|
| Signal (terminal) | Front left wheel sensor signal | |||||
| Threshold | When a malfunction is detected in front left wheel sensor. | |||||
| Diagnosis delay time | 1 second or less | |||||
| 2 | Diagnosis condition |
|
||||
| Signal (terminal) | Front right wheel sensor signal | |||||
| Threshold | When a malfunction is detected in front right wheel sensor. | |||||
| Diagnosis delay time | 1 second or less | |||||
| 3 | Diagnosis condition |
|
||||
| Signal (terminal) | Rear left wheel sensor signal | |||||
| Threshold | When a malfunction is detected in rear left wheel sensor. | |||||
| Diagnosis delay time | 1 second or less | |||||
| 4 | Diagnosis condition |
|
||||
| Signal (terminal) | Rear right wheel sensor signal | |||||
| Threshold | When a malfunction is detected in rear right wheel sensor. | |||||
| Diagnosis delay time | 1 second or less | |||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1068-96" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK WHEEL HUB ASSEMBLY
Check that there is no excessive looseness in wheel hub assembly.
Front: Refer to FRONT WHEEL HUB AND KNUCKLE : Periodic Maintenance Operation.
Rear: Refer to REAR WHEEL HUB : Periodic Maintenance Operation.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace the wheel hub assembly. GO TO 2.
Front: Refer to FRONT WHEEL HUB AND KNUCKLE : Removal & Installation.
Rear: Refer to REAR WHEEL HUB : Removal & Installation.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
CHECK TIRE
Power switch OFF.
Check the tire air pressure, wear and size. Refer to TIRE AIR PRESSURE : Service Data.
Is the inspection result normal?
YES>>GO TO 6.
NO>>Adjust air pressure or replace tire. GO TO 4.
CHECK DATA MONITOR (1)
With CONSULT
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 5.
NO>>GO TO 6.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1068-96” detected?
YES>>GO TO 6.
NO>>INSPECTION END
CHECK WHEEL SENSOR AND SENSOR ROTOR
Disconnect 12V battery negative terminal.
Disconnect wheel sensor harness connector.
Remove dust and foreign matter adhered to the wheel sensor and sensor rotor with a vacuum dust collector through the wheel sensor mounting hole.
Front: Refer to FRONT WHEEL SENSOR : Exploded View.
Rear: Refer to REAR WHEEL SENSOR : Exploded View.
GO TO 7.
CHECK WHEEL SENSOR
Check the wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 11.
NO>>GO TO 8.
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 9.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the wheel sensor.
Front: Refer to FRONT WHEEL SENSOR : Removal & Installation.
Rear: Refer to REAR WHEEL SENSOR : Removal & Installation.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 10.
NO>>GO TO 22.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1068-96” detected?
YES>>GO TO 22.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 14.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 12.
CHECK DATA MONITOR (2)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 13.
NO>>GO TO 14.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1068-96” detected?
YES>>GO TO 14.
NO>>INSPECTION END
CHECK TERMINAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Disconnect wheel sensor harness connector.
Check the wheel sensor terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 17.
NO>>Repair / replace harness, connector, or terminal. GO TO 15.
CHECK DATA MONITOR (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 16.
NO>>GO TO 17.
PERFORM SELF-DIAGNOSIS (4)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1068-96” detected?
YES>>GO TO 17.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and wheel sensor harness connector.
ABS actuator and electric unit (control unit) — Continuity Connector Terminal B2 24, 7 (Front left) Ground Not existed 21, 26 (Front right) 39, 23 (Rear left) 22, 37 (Rear right)
Is the inspection result normal?
YES>>GO TO 18.
NO>>Repair / replace harness or connector. GO TO 18.
CHECK DATA MONITOR (4)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 19.
NO>>GO TO 20.
PERFORM SELF-DIAGNOSIS (5)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1068-96” detected?
YES>>GO TO 20.
NO>>INSPECTION END
REPLACE WHEEL SENSOR (2)
With CONSULT
Replace the wheel sensor.
Front: Refer to FRONT WHEEL SENSOR : Removal & Installation.
Rear: Refer to REAR WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 21.
NO>>GO TO 22.
PERFORM SELF-DIAGNOSIS (6)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1068-96” detected?
YES>>GO TO 22.
NO>>INSPECTION END
REPLACE SENSOR ROTOR
With CONSULT
Replace the sensor rotor.
Front: Refer to FRONT SENSOR ROTOR : Removal & Installation.
Rear: Refer to REAR SENSOR ROTOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1068-96” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C1069-95 Wheel Sensor Nissan Ariya first Gen
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | ||||
|---|---|---|---|---|---|---|
| C1069 | 95 | Rear wheel sensor | 1 | Diagnosis condition |
|
|
| Signal (terminal) | Rear left wheel sensor signal | |||||
| Threshold | When a malfunction is detected in rear left wheel sensor. | |||||
| Diagnosis delay time | 1 second or less | |||||
| 2 | Diagnosis condition |
|
||||
| Signal (terminal) | Rear right wheel sensor signal | |||||
| Threshold | When a malfunction is detected in rear right wheel sensor. | |||||
| Diagnosis delay time | 1 second or less | |||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1069-95" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK WHEEL HUB ASSEMBLY
Check that there is no excessive looseness in rear wheel hub assembly. Refer to REAR WHEEL HUB : Periodic Maintenance Operation.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace the rear wheel hub assembly. Refer to REAR WHEEL HUB : Removal & Installation. GO TO 2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
CHECK TIRE
Power switch OFF.
Check the rear tire air pressure, wear and size. Refer to TIRE AIR PRESSURE : Service Data.
Is the inspection result normal?
YES>>GO TO 6.
NO>>Adjust air pressure or replace rear tire. GO TO 4.
CHECK DATA MONITOR (1)
With CONSULT
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 5.
NO>>GO TO 6.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1069-95” detected?
YES>>GO TO 6.
NO>>INSPECTION END
CHECK WHEEL SENSOR AND SENSOR ROTOR
Disconnect 12V battery negative terminal.
Disconnect rear wheel sensor harness connector.
Remove dust and foreign matter adhered to the rear wheel sensor and rear sensor rotor with a vacuum dust collector through the rear wheel sensor mounting hole.
GO TO 7.
CHECK WHEEL SENSOR
Check the rear wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 11.
NO>>GO TO 8.
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 9.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the rear wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 10.
NO>>GO TO 22.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1069-95” detected?
YES>>GO TO 22.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the rear wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 14.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 12.
CHECK DATA MONITOR (2)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 13.
NO>>GO TO 14.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1069-95” detected?
YES>>GO TO 14.
NO>>INSPECTION END
CHECK TERMINAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Disconnect rear wheel sensor harness connector.
Check the rear wheel sensor terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 17.
NO>>Repair / replace harness, connector, or terminal. GO TO 15.
CHECK DATA MONITOR (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect rear wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 16.
NO>>GO TO 17.
PERFORM SELF-DIAGNOSIS (4)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1069-95” detected?
YES>>GO TO 17.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect rear wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and rear wheel sensor harness connector.
ABS actuator and electric unit (control unit) — Continuity Connector Terminal B2 39, 23 (Rear left) Ground Not existed 22, 37 (Rear right)
Is the inspection result normal?
YES>>GO TO 18.
NO>>Repair / replace harness or connector. GO TO 18.
CHECK DATA MONITOR (4)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect rear wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 19.
NO>>GO TO 20.
PERFORM SELF-DIAGNOSIS (5)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1069-95” detected?
YES>>GO TO 20.
NO>>INSPECTION END
REPLACE WHEEL SENSOR (2)
With CONSULT
Replace the rear wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 21.
NO>>GO TO 22.
PERFORM SELF-DIAGNOSIS (6)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1069-95” detected?
YES>>GO TO 22.
NO>>INSPECTION END
REPLACE SENSOR ROTOR
With CONSULT
Replace the rear sensor rotor. Refer to REAR SENSOR ROTOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1067-07” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C106a-04 Wheel Sensor Nissan Ariya 2026
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | ||||
|---|---|---|---|---|---|---|
| C106A | 04 | Wheel sensor | 1 | Diagnosis condition |
|
|
| Signal (terminal) | Front left wheel sensor signal | |||||
| Threshold | When a malfunction is detected in front left wheel sensor. | |||||
| Diagnosis delay time | 1 second or less | |||||
| 2 | Diagnosis condition |
|
||||
| Signal (terminal) | Front right wheel sensor signal | |||||
| Threshold | When a malfunction is detected in front right wheel sensor. | |||||
| Diagnosis delay time | 1 second or less | |||||
| 3 | Diagnosis condition |
|
||||
| Signal (terminal) | Rear left wheel sensor signal | |||||
| Threshold | When a malfunction is detected in rear left wheel sensor. | |||||
| Diagnosis delay time | 1 second or less | |||||
| 4 | Diagnosis condition |
|
||||
| Signal (terminal) | Rear right wheel sensor signal | |||||
| Threshold | When a malfunction is detected in rear right wheel sensor. | |||||
| Diagnosis delay time | 1 second or less | |||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106A-04" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK TIRE
Check the tire air pressure, wear and size. Refer to TIRE AIR PRESSURE : Service Data.
Is the inspection result normal?
YES>>GO TO 6.
NO>>Adjust air pressure or replace tire. GO TO 2.
CHECK DATA MONITOR (1)
With CONSULT
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 3.
NO>>GO TO 4.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106A-04” detected?
YES>>GO TO 4.
NO>>INSPECTION END
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.
CHECK WHEEL SENSOR AND SENSOR ROTOR
Disconnect 12V battery negative terminal.
Disconnect wheel sensor harness connector.
Remove dust and foreign matter adhered to the each wheel sensor and each sensor rotor with a vacuum dust collector through the each wheel sensor mounting hole.
Front: Refer to FRONT WHEEL SENSOR : Exploded View.
Rear: Refer to REAR WHEEL SENSOR : Exploded View.
GO TO 6.
CHECK WHEEL SENSOR
Check the wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 10.
NO>>GO TO 7.
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 8.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the wheel sensor.
Front: Refer to FRONT WHEEL SENSOR : Removal & Installation.
Rear: Refer to REAR WHEEL SENSOR : Removal & Installation.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 9.
NO>>GO TO 21.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106A-04” detected?
YES>>GO TO 21.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 13.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 11.
CHECK DATA MONITOR (2)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 12.
NO>>GO TO 13.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106A-04” detected?
YES>>GO TO 13.
NO>>INSPECTION END
CHECK TERMINAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Disconnect wheel sensor harness connector.
Check the wheel sensor terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 16.
NO>>Repair / replace harness, connector, or terminal. GO TO 14.
CHECK DATA MONITOR (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 15.
NO>>GO TO 16.
PERFORM SELF-DIAGNOSIS (4)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106A-04” detected?
YES>>GO TO 16.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and front wheel sensor harness connector.
Measurement connector and terminal for power supply circuit
ABS actuator and electric unit (control unit) Wheel sensor Continuity Connector Terminal Connector Terminal B2 24 B177 (Front left) 1 Existed 21 E109 (Front right) 39 B178 (Rear left) 22 B180 (Rear right) Measurement connector and terminal for signal circuit
ABS actuator and electric unit (control unit) Wheel sensor Continuity Connector Terminal Connector Terminal B2 7 B177 (Front left) 2 Existed 26 E109 (Front right) 23 B178 (Rear left) 37 B180 (Rear right)
Check the continuity between ABS actuator and electric unit (control unit) harness connector and the ground.
ABS actuator and electric unit (control unit) — Continuity Connector Terminal B2 24, 7 Ground Not existed 21, 26 39, 23 22, 37
Is the inspection result normal?
YES>>GO TO 17.
NO>>Repair / replace harness or connector. GO TO 17.
CHECK DATA MONITOR (4)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 18.
NO>>GO TO 19.
PERFORM SELF-DIAGNOSIS (5)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106A-04” detected?
YES>>GO TO 19.
NO>>INSPECTION END
REPLACE WHEEL SENSOR (2)
With CONSULT
Replace the wheel sensor.
Front: Refer to FRONT WHEEL SENSOR : Removal & Installation.
Rear: Refer to REAR WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 20.
NO>>GO TO 21.
PERFORM SELF-DIAGNOSIS (6)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106A-04” detected?
YES>>GO TO 21.
NO>>INSPECTION END
REPLACE SENSOR ROTOR
With CONSULT
Replace the sensor rotor.
Front: Refer to FRONT SENSOR ROTOR : Removal & Installation.
Rear: Refer to REAR SENSOR ROTOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106A-04” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C106a-55 Wheel Sensor Nissan Ariya first Gen
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | ||||
|---|---|---|---|---|---|---|
| C106A | 55 | Wheel sensor | 1 | Diagnosis condition |
|
|
| Signal (terminal) | Front left wheel sensor signal | |||||
| Threshold | When a malfunction is detected in front left wheel sensor. | |||||
| Diagnosis delay time | 1 second or less | |||||
| 2 | Diagnosis condition |
|
||||
| Signal (terminal) | Front right wheel sensor signal | |||||
| Threshold | When a malfunction is detected in front right wheel sensor. | |||||
| Diagnosis delay time | 1 second or less | |||||
| 3 | Diagnosis condition |
|
||||
| Signal (terminal) | Rear left wheel sensor signal | |||||
| Threshold | When a malfunction is detected in rear left wheel sensor. | |||||
| Diagnosis delay time | 1 second or less | |||||
| 4 | Diagnosis condition |
|
||||
| Signal (terminal) | Rear right wheel sensor signal | |||||
| Threshold | When a malfunction is detected in rear right wheel sensor. | |||||
| Diagnosis delay time | 1 second or less | |||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106A-55" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK TIRE
Check the tire air pressure, wear and size. Refer to TIRE AIR PRESSURE : Service Data.
Is the inspection result normal?
YES>>GO TO 6.
NO>>Adjust air pressure or replace tire. GO TO 2.
CHECK DATA MONITOR (1)
With CONSULT
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 3.
NO>>GO TO 4.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106A-55” detected?
YES>>GO TO 4.
NO>>INSPECTION END
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.
CHECK WHEEL SENSOR AND SENSOR ROTOR
Disconnect 12V battery negative terminal.
Disconnect wheel sensor harness connector.
Remove dust and foreign matter adhered to the each wheel sensor and each sensor rotor with a vacuum dust collector through the each wheel sensor mounting hole.
Front: Refer to FRONT WHEEL SENSOR : Exploded View.
Rear: Refer to REAR WHEEL SENSOR : Exploded View.
GO TO 6.
CHECK WHEEL SENSOR
Check the wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 10.
NO>>GO TO 7.
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 8.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the wheel sensor.
Front: Refer to FRONT WHEEL SENSOR : Removal & Installation.
Rear: Refer to REAR WHEEL SENSOR : Removal & Installation.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 9.
NO>>GO TO 21.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106A-55” detected?
YES>>GO TO 21.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 13.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 11.
CHECK DATA MONITOR (2)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 12.
NO>>GO TO 13.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106A-55” detected?
YES>>GO TO 13.
NO>>INSPECTION END
CHECK TERMINAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Disconnect wheel sensor harness connector.
Check the wheel sensor terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 16.
NO>>Repair / replace harness, connector, or terminal. GO TO 14.
CHECK DATA MONITOR (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 15.
NO>>GO TO 16.
PERFORM SELF-DIAGNOSIS (4)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106A-55” detected?
YES>>GO TO 16.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and wheel sensor harness connector.
Measurement connector and terminal for power supply circuit
ABS actuator and electric unit (control unit) Wheel sensor Continuity Connector Terminal Connector Terminal B2 24 B177 (Front left) 1 Existed 21 E109 (Front right) 39 B178 (Rear left) 22 B180 (Rear right) Measurement connector and terminal for signal circuit
ABS actuator and electric unit (control unit) Wheel sensor Continuity Connector Terminal Connector Terminal B2 7 B177 (Front left) 2 Existed 26 E109 (Front right) 23 B178 (Rear left) 37 B180 (Rear right)
Check the continuity between ABS actuator and electric unit (control unit) harness connector and the ground.
ABS actuator and electric unit (control unit) — Continuity Connector Terminal B2 24, 7 Ground Not existed 21, 26 39, 23 22, 37
Is the inspection result normal?
YES>>GO TO 17.
NO>>Repair / replace harness or connector. GO TO 17.
CHECK DATA MONITOR (4)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 18.
NO>>GO TO 19.
PERFORM SELF-DIAGNOSIS (5)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106A-55” detected?
YES>>GO TO 19.
NO>>INSPECTION END
REPLACE WHEEL SENSOR (2)
With CONSULT
Replace the wheel sensor.
Front: Refer to FRONT WHEEL SENSOR : Removal & Installation.
Rear: Refer to REAR WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 20.
NO>>GO TO 21.
PERFORM SELF-DIAGNOSIS (6)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106A-55” detected?
YES>>GO TO 21.
NO>>INSPECTION END
REPLACE SENSOR ROTOR
With CONSULT
Replace the sensor rotor.
Front: Refer to FRONT SENSOR ROTOR : Removal & Installation.
Rear: Refer to REAR SENSOR ROTOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106A-55” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C106a-62 Wheel Sensor Nissan Ariya: FE0
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | ||||
|---|---|---|---|---|---|---|
| C106A | 62 | Wheel sensor | 1 | Diagnosis condition |
|
|
| Signal (terminal) | Front left wheel sensor signal | |||||
| Threshold | When a malfunction is detected in front left wheel sensor. | |||||
| Diagnosis delay time | 1 second or less | |||||
| 2 | Diagnosis condition |
|
||||
| Signal (terminal) | Front right wheel sensor signal | |||||
| Threshold | When a malfunction is detected in front right wheel sensor. | |||||
| Diagnosis delay time | 1 second or less | |||||
| 3 | Diagnosis condition |
|
||||
| Signal (terminal) | Rear left wheel sensor signal | |||||
| Threshold | When a malfunction is detected in rear left wheel sensor. | |||||
| Diagnosis delay time | 1 second or less | |||||
| 4 | Diagnosis condition |
|
||||
| Signal (terminal) | Rear right wheel sensor signal | |||||
| Threshold | When a malfunction is detected in rear right wheel sensor. | |||||
| Diagnosis delay time | 1 second or less | |||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106A-62" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK TIRE
Check the tire air pressure, wear and size. Refer to TIRE AIR PRESSURE : Service Data.
Is the inspection result normal?
YES>>GO TO 6.
NO>>Adjust air pressure or replace tire. GO TO 2.
CHECK DATA MONITOR (1)
With CONSULT
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 3.
NO>>GO TO 4.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106A-62” detected?
YES>>GO TO 4.
NO>>INSPECTION END
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.
CHECK WHEEL SENSOR AND SENSOR ROTOR
Disconnect 12V battery negative terminal.
Disconnect wheel sensor harness connector.
Remove dust and foreign matter adhered to the each wheel sensor and each sensor rotor with a vacuum dust collector through the each wheel sensor mounting hole.
Front: Refer to FRONT WHEEL SENSOR : Exploded View.
Rear: Refer to REAR WHEEL SENSOR : Exploded View.
GO TO 6.
CHECK WHEEL SENSOR
Check the wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 10.
NO>>GO TO 7.
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 8.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the wheel sensor.
Front: Refer to FRONT WHEEL SENSOR : Removal & Installation.
Rear: Refer to REAR WHEEL SENSOR : Removal & Installation.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 9.
NO>>GO TO 21.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106A-62” detected?
YES>>GO TO 21.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 13.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 11.
CHECK DATA MONITOR (2)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 12.
NO>>GO TO 13.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106A-62” detected?
YES>>GO TO 13.
NO>>INSPECTION END
CHECK TERMINAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Disconnect wheel sensor harness connector.
Check the wheel sensor terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 16.
NO>>Repair / replace harness, connector, or terminal. GO TO 14.
CHECK DATA MONITOR (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 15.
NO>>GO TO 16.
PERFORM SELF-DIAGNOSIS (4)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106A-62” detected?
YES>>GO TO 16.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and wheel sensor harness connector.
Measurement connector and terminal for power supply circuit
ABS actuator and electric unit (control unit) Wheel sensor Continuity Connector Terminal Connector Terminal B2 24 B177 (Front left) 1 Existed 21 E109 (Front right) 39 B178 (Rear left) 22 B180 (Rear right) Measurement connector and terminal for signal circuit
ABS actuator and electric unit (control unit) Wheel sensor Continuity Connector Terminal Connector Terminal B2 7 B177 (Front left) 2 Existed 26 E109 (Front right) 23 B178 (Rear left) 37 B180 (Rear right)
Check the continuity between ABS actuator and electric unit (control unit) harness connector and the ground.
ABS actuator and electric unit (control unit) — Continuity Connector Terminal B2 24, 7 Ground Not existed 21, 26 39, 23 22, 37
Is the inspection result normal?
YES>>GO TO 17.
NO>>Repair / replace harness or connector. GO TO 17.
CHECK DATA MONITOR (4)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 18.
NO>>GO TO 19.
PERFORM SELF-DIAGNOSIS (5)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106A-62” detected?
YES>>GO TO 19.
NO>>INSPECTION END
REPLACE WHEEL SENSOR (2)
With CONSULT
Replace the wheel sensor.
Front: Refer to FRONT WHEEL SENSOR : Removal & Installation.
Rear: Refer to REAR WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 20.
NO>>GO TO 21.
PERFORM SELF-DIAGNOSIS (6)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106A-62” detected?
YES>>GO TO 21.
NO>>INSPECTION END
REPLACE SENSOR ROTOR
With CONSULT
Replace the sensor rotor.
Front: Refer to FRONT SENSOR ROTOR : Removal & Installation.
Rear: Refer to REAR SENSOR ROTOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106A-62” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C106a-64 Wheel Sensor Nissan Ariya
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | ||||
|---|---|---|---|---|---|---|
| C106A | 64 | Wheel sensor | 1 | Diagnosis condition |
|
|
| Signal (terminal) | Front left wheel sensor signal | |||||
| Threshold | When a malfunction is detected in front left wheel sensor. | |||||
| Diagnosis delay time | 1 second or less | |||||
| 2 | Diagnosis condition |
|
||||
| Signal (terminal) | Front right wheel sensor signal | |||||
| Threshold | When a malfunction is detected in front right wheel sensor. | |||||
| Diagnosis delay time | 1 second or less | |||||
| 3 | Diagnosis condition |
|
||||
| Signal (terminal) | Rear left wheel sensor signal | |||||
| Threshold | When a malfunction is detected in rear left wheel sensor. | |||||
| Diagnosis delay time | 1 second or less | |||||
| 4 | Diagnosis condition |
|
||||
| Signal (terminal) | Rear right wheel sensor signal | |||||
| Threshold | When a malfunction is detected in rear right wheel sensor. | |||||
| Diagnosis delay time | 1 second or less | |||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106A-64" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK TIRE
Check the tire air pressure, wear and size. Refer to TIRE AIR PRESSURE : Service Data.
Is the inspection result normal?
YES>>GO TO 6.
NO>>Adjust air pressure or replace tire. GO TO 2.
CHECK DATA MONITOR (1)
With CONSULT
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 3.
NO>>GO TO 4.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106A-64” detected?
YES>>GO TO 4.
NO>>INSPECTION END
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.
CHECK WHEEL SENSOR AND SENSOR ROTOR
Disconnect 12V battery negative terminal.
Disconnect wheel sensor harness connector.
Remove dust and foreign matter adhered to the each wheel sensor and each sensor rotor with a vacuum dust collector through the each wheel sensor mounting hole.
Front: Refer to FRONT WHEEL SENSOR : Exploded View.
Rear: Refer to REAR WHEEL SENSOR : Exploded View.
GO TO 6.
CHECK WHEEL SENSOR
Check the wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 10.
NO>>GO TO 7.
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 8.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the wheel sensor.
Front: Refer to FRONT WHEEL SENSOR : Removal & Installation.
Rear: Refer to REAR WHEEL SENSOR : Removal & Installation.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 9.
NO>>GO TO 21.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106A-64” detected?
YES>>GO TO 21.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 13.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 11.
CHECK DATA MONITOR (2)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 12.
NO>>GO TO 13.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106A-64” detected?
YES>>GO TO 13.
NO>>INSPECTION END
CHECK TERMINAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Disconnect wheel sensor harness connector.
Check the wheel sensor terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 16.
NO>>Repair / replace harness, connector, or terminal. GO TO 14.
CHECK DATA MONITOR (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 15.
NO>>GO TO 16.
PERFORM SELF-DIAGNOSIS (4)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106A-64” detected?
YES>>GO TO 16.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and wheel sensor harness connector.
Measurement connector and terminal for power supply circuit
ABS actuator and electric unit (control unit) Wheel sensor Continuity Connector Terminal Connector Terminal B2 24 B177 (Front left) 1 Existed 21 E109 (Front right) 39 B178 (Rear left) 22 B180 (Rear right) Measurement connector and terminal for signal circuit
ABS actuator and electric unit (control unit) Wheel sensor Continuity Connector Terminal Connector Terminal B2 7 B177 (Front left) 2 Existed 26 E109 (Front right) 23 B178 (Rear left) 37 B180 (Rear right)
Check the continuity between ABS actuator and electric unit (control unit) harness connector and the ground.
ABS actuator and electric unit (control unit) — Continuity Connector Terminal B2 24, 7 Ground Not existed 21, 26 39, 23 22, 37
Is the inspection result normal?
YES>>GO TO 17.
NO>>Repair / replace harness or connector. GO TO 17.
CHECK DATA MONITOR (4)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 18.
NO>>GO TO 19.
PERFORM SELF-DIAGNOSIS (5)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106A-64” detected?
YES>>GO TO 19.
NO>>INSPECTION END
REPLACE WHEEL SENSOR (2)
With CONSULT
Replace the wheel sensor.
Front: Refer to FRONT WHEEL SENSOR : Removal & Installation.
Rear: Refer to REAR WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 20.
NO>>GO TO 21.
PERFORM SELF-DIAGNOSIS (6)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106A-64” detected?
YES>>GO TO 21.
NO>>INSPECTION END
REPLACE SENSOR ROTOR
With CONSULT
Replace the sensor rotor.
Front: Refer to FRONT SENSOR ROTOR : Removal & Installation.
Rear: Refer to REAR SENSOR ROTOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106A-64” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C106a-95 Wheel Sensor Nissan Ariya: FE0
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | ||||
|---|---|---|---|---|---|---|
| C106A | 95 | Wheel sensor | 1 | Diagnosis condition |
|
|
| Signal (terminal) | Front left wheel sensor signal | |||||
| Threshold | When a malfunction is detected in front left wheel sensor. | |||||
| Diagnosis delay time | 1 second or less | |||||
| 2 | Diagnosis condition |
|
||||
| Signal (terminal) | Front right wheel sensor signal | |||||
| Threshold | When a malfunction is detected in front right wheel sensor. | |||||
| Diagnosis delay time | 1 second or less | |||||
| 3 | Diagnosis condition |
|
||||
| Signal (terminal) | Rear left wheel sensor signal | |||||
| Threshold | When a malfunction is detected in rear left wheel sensor. | |||||
| Diagnosis delay time | 1 second or less | |||||
| 4 | Diagnosis condition |
|
||||
| Signal (terminal) | Rear right wheel sensor signal | |||||
| Threshold | When a malfunction is detected in rear right wheel sensor. | |||||
| Diagnosis delay time | 1 second or less | |||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106A-95" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK TIRE
Check the tire air pressure, wear and size. Refer to TIRE AIR PRESSURE : Service Data.
Is the inspection result normal?
YES>>GO TO 6.
NO>>Adjust air pressure or replace tire. GO TO 2.
CHECK DATA MONITOR (1)
With CONSULT
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 3.
NO>>GO TO 4.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106A-95” detected?
YES>>GO TO 4.
NO>>INSPECTION END
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.
CHECK WHEEL SENSOR AND SENSOR ROTOR
Disconnect 12V battery negative terminal.
Disconnect wheel sensor harness connector.
Remove dust and foreign matter adhered to the each wheel sensor and each sensor rotor with a vacuum dust collector through the each wheel sensor mounting hole.
Front: Refer to FRONT WHEEL SENSOR : Exploded View.
Rear: Refer to REAR WHEEL SENSOR : Exploded View.
GO TO 6.
CHECK WHEEL SENSOR
Check the wheel sensor for damage.
Is the inspection result normal?
YES>>GO TO 10.
NO>>GO TO 7.
CHECK WHEEL SENSOR OUTPUT SIGNAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect wheel sensor harness connector.
Connect ABS active wheel sensor tester (SST: J-45741-A) to wheel sensor using appropriate adapter.
Turn the ABS active wheel sensor tester power switch ON.
Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
Does the ABS active wheel sensor tester detect a signal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>GO TO 8.
REPLACE WHEEL SENSOR (1)
With CONSULT
Replace the wheel sensor.
Front: Refer to FRONT WHEEL SENSOR : Removal & Installation.
Rear: Refer to REAR WHEEL SENSOR : Removal & Installation.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 9.
NO>>GO TO 21.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106A-95” detected?
YES>>GO TO 21.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 13.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 11.
CHECK DATA MONITOR (2)
With CONSULT
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 12.
NO>>GO TO 13.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106A-95” detected?
YES>>GO TO 13.
NO>>INSPECTION END
CHECK TERMINAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Disconnect wheel sensor harness connector.
Check the wheel sensor terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 16.
NO>>Repair / replace harness, connector, or terminal. GO TO 14.
CHECK DATA MONITOR (3)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 15.
NO>>GO TO 16.
PERFORM SELF-DIAGNOSIS (4)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106A-95” detected?
YES>>GO TO 16.
NO>>INSPECTION END
CHECK WHEEL SENSOR HARNESS
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Disconnect wheel sensor harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and wheel sensor harness connector.
Measurement connector and terminal for power supply circuit
ABS actuator and electric unit (control unit) Wheel sensor Continuity Connector Terminal Connector Terminal B2 24 B177 (Front left) 1 Existed 21 E109 (Front right) 39 B178 (Rear left) 22 B180 (Rear right) Measurement connector and terminal for signal circuit
ABS actuator and electric unit (control unit) Wheel sensor Continuity Connector Terminal Connector Terminal B2 7 B177 (Front left) 2 Existed 26 E109 (Front right) 23 B178 (Rear left) 37 B180 (Rear right)
Check the continuity between ABS actuator and electric unit (control unit) harness connector and the ground.
ABS actuator and electric unit (control unit) — Continuity Connector Terminal B2 24, 7 Ground Not existed 21, 26 39, 23 22, 37
Is the inspection result normal?
YES>>GO TO 17.
NO>>Repair / replace harness or connector. GO TO 17.
CHECK DATA MONITOR (4)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect wheel sensor harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 18.
NO>>GO TO 19.
PERFORM SELF-DIAGNOSIS (5)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106A-95” detected?
YES>>GO TO 19.
NO>>INSPECTION END
REPLACE WHEEL SENSOR (2)
With CONSULT
Replace the wheel sensor.
Front: Refer to FRONT WHEEL SENSOR : Removal & Installation.
Rear: Refer to REAR WHEEL SENSOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Select “ABS” and “Data monitor”, check “Front left wheel speed”, “Front right wheel speed“, “Rear left wheel speed“, and “Rear right wheel speed“.
Read a value (wheel speed) of all wheel sensor.
GO TO 20.
NO>>GO TO 21.
PERFORM SELF-DIAGNOSIS (6)
With CONSULT
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106A-95” detected?
YES>>GO TO 21.
NO>>INSPECTION END
REPLACE SENSOR ROTOR
With CONSULT
Replace the sensor rotor.
Front: Refer to FRONT SENSOR ROTOR : Removal & Installation.
Rear: Refer to REAR SENSOR ROTOR : Removal & Installation.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106A-95” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C106b-64 Stop Lamp Switch Nissan Ariya SUV
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C106B | 64 | Stop lamp switch | Diagnosis condition |
|
|
| Signal (terminal) | CAN communication signal | ||||
| Threshold | When stop lamp switch signal is not input when brake pedal operates. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106B-64" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK BCM SYSTEM
With CONSULT
Perform self-diagnosis for “BCM”.
Is DTC detected?
YES>>Check the DTC. Refer to DTC Index.
NO>>GO TO 2.
CHECK CONNECTOR AND TERMINAL
Disconnect 12V battery negative terminal.
Disconnect BCM harness connector.
Check the BCM harness connector for disconnection or looseness.
Check the BCM terminals for damage or loose connection with harness connector.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, or terminal. GO TO 3.
PERFORM SELF-DIAGNOSIS
With CONSULT
Connect BCM harness connector.
Connect ABS actuator and electric unit (control unit) harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC "C106B-64" detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C106c-01 Pressure Sensor Nissan Ariya
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C106C | 01 | Pressure sensor | Diagnosis condition |
|
|
| Signal (terminal) | — | ||||
| Threshold | When a malfunction is detected in pressure sensor. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106C-01" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
STOP LAMP SWITCH SYSTEM
Check the stop lamp switch system. Refer to Component Function Check.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace stop lamp switch system.
CHECK BRAKE FLUID LEAKAGE
Check the brake fluid leakage. Refer to BRAKE FLUID : Inspection.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair or replace brake fluid leakage part.
CHECK BRAKE PIPING
Check the brake piping.
Front: Refer to FRONT BRAKE PIPING : Inspection.
Rear: Refer to REAR BRAKE PIPING : Inspection.
Is the inspection result normal?
YES>>GO TO 4.
NO>>Repair or replace error-detected brake piping.
Front: Refer to REAR BRAKE PIPING : Inspection.
Rear: Refer to REAR BRAKE PIPING : Removal & Installation.
CHECK BRAKE PEDAL
Check the brake pedal.
Brake pedal height: Refer to BRAKE PEDAL : Periodic Maintenance Operation.
Brake pedal assembly: Refer to BRAKE PEDAL : Inspection and Adjustment.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Adjust the brake pedal height or replace brake pedal assembly.
Adjust the brake pedal: Refer to BRAKE PEDAL : Periodic Maintenance Operation.
Replace the brake pedal: Refer to BRAKE PEDAL : Removal & Installation.
CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT
Check the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Inspection.
Is the inspection result normal?
YES>>GO TO 6.
NO>>Repair or replace electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.
CHECK FRONT DISC BRAKE
Check the front disc brake. Refer to FRONT BRAKE CALIPER ASSEMBLY : Inspection.
Is the inspection result normal?
YES>>GO TO 7.
NO>>Repair or replace front disc brake. Refer to FRONT BRAKE CALIPER ASSEMBLY : Removal & Installation.
CHECK REAR DISC BRAKE
Check the rear disc brake. Refer to REAR BRAKE CALIPER ASSEMBLY : Inspection.
Is the inspection result normal?
YES>>GO TO 8.
NO>>Repair or replace rear disc brake. Refer to REAR BRAKE CALIPER ASSEMBLY : Removal & Installation.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 9.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
PERFORM SELF-DIAGNOSIS
With CONSULT
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY, and drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106C-01” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>Check the ABS actuator and electric unit (control unit) harness connector and terminal for damage, looseness and disconnection. Repair / replace harness, connector, or terminal.
C106c-02 Pressure Sensor Nissan Ariya
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C106C | 02 | Pressure sensor | Diagnosis condition |
|
|
| Signal (terminal) | — | ||||
| Threshold | When a malfunction is detected in pressure sensor. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106C-02" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
STOP LAMP SWITCH SYSTEM
Check the stop lamp switch system. Refer to Component Function Check.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace stop lamp switch system.
CHECK BRAKE FLUID LEAKAGE
Check the brake fluid leakage. Refer to BRAKE FLUID : Inspection.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair or replace brake fluid leakage part.
CHECK BRAKE PIPING
Check the brake piping.
Front: Refer to FRONT BRAKE PIPING : Inspection.
Rear: Refer to REAR BRAKE PIPING : Inspection.
Is the inspection result normal?
YES>>GO TO 4.
NO>>Repair or replace error-detected brake piping.
Front: Refer to REAR BRAKE PIPING : Inspection.
Rear: Refer to REAR BRAKE PIPING : Removal & Installation.
CHECK BRAKE PEDAL
Check the brake pedal.
Brake pedal height: Refer to BRAKE PEDAL : Periodic Maintenance Operation.
Brake pedal assembly: Refer to BRAKE PEDAL : Inspection and Adjustment.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Adjust the brake pedal height or replace brake pedal assembly.
Adjust the brake pedal: Refer to BRAKE PEDAL : Periodic Maintenance Operation.
Replace the brake pedal: Refer to BRAKE PEDAL : Removal & Installation.
CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT
Check the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Inspection.
Is the inspection result normal?
YES>>GO TO 6.
NO>>Repair or replace electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.
CHECK FRONT DISC BRAKE
Check the front disc brake. Refer to FRONT BRAKE CALIPER ASSEMBLY : Inspection.
Is the inspection result normal?
YES>>GO TO 7.
NO>>Repair or replace front disc brake. Refer to FRONT BRAKE CALIPER ASSEMBLY : Removal & Installation.
CHECK REAR DISC BRAKE
Check the rear disc brake. Refer to REAR BRAKE CALIPER ASSEMBLY : Inspection.
Is the inspection result normal?
YES>>GO TO 8.
NO>>Repair or replace rear disc brake. Refer to REAR BRAKE CALIPER ASSEMBLY : Removal & Installation.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 9.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
PERFORM SELF-DIAGNOSIS
With CONSULT
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY, and drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106C-02” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>Check the ABS actuator and electric unit (control unit) harness connector and terminal for damage, looseness and disconnection. Repair / replace harness, connector, or terminal.
C106c-16 Pressure Sensor Nissan Ariya 2026
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C106C | 16 | Pressure sensor | Diagnosis condition |
|
|
| Signal (terminal) | — | ||||
| Threshold | When a malfunction is detected in pressure sensor. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106C-16" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
STOP LAMP SWITCH SYSTEM
Check the stop lamp switch system. Refer to Component Function Check.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace stop lamp switch system.
CHECK BRAKE FLUID LEAKAGE
Check the brake fluid leakage. Refer to BRAKE FLUID : Inspection.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair or replace brake fluid leakage part.
CHECK BRAKE PIPING
Check the brake piping.
Front: Refer to FRONT BRAKE PIPING : Inspection.
Rear: Refer to REAR BRAKE PIPING : Inspection.
Is the inspection result normal?
YES>>GO TO 4.
NO>>Repair or replace error-detected brake piping.
Front: Refer to REAR BRAKE PIPING : Inspection.
Rear: Refer to REAR BRAKE PIPING : Removal & Installation.
CHECK BRAKE PEDAL
Check the brake pedal.
Brake pedal height: Refer to BRAKE PEDAL : Periodic Maintenance Operation.
Brake pedal assembly: Refer to BRAKE PEDAL : Inspection and Adjustment.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Adjust the brake pedal height or replace brake pedal assembly.
Adjust the brake pedal: Refer to BRAKE PEDAL : Periodic Maintenance Operation.
Replace the brake pedal: Refer to BRAKE PEDAL : Removal & Installation.
CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT
Check the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Inspection.
Is the inspection result normal?
YES>>GO TO 6.
NO>>Repair or replace electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.
CHECK FRONT DISC BRAKE
Check the front disc brake. Refer to FRONT BRAKE CALIPER ASSEMBLY : Inspection.
Is the inspection result normal?
YES>>GO TO 7.
NO>>Repair or replace front disc brake. Refer to FRONT BRAKE CALIPER ASSEMBLY : Removal & Installation.
CHECK REAR DISC BRAKE
Check the rear disc brake. Refer to REAR BRAKE CALIPER ASSEMBLY : Inspection.
Is the inspection result normal?
YES>>GO TO 8.
NO>>Repair or replace rear disc brake. Refer to REAR BRAKE CALIPER ASSEMBLY : Removal & Installation.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 9.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
PERFORM SELF-DIAGNOSIS
With CONSULT
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY, and drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106C-16” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>Check the ABS actuator and electric unit (control unit) harness connector and terminal for damage, looseness and disconnection. Repair / replace harness, connector, or terminal.
C106c-17 Pressure Sensor Nissan Ariya: FE0
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C106C | 17 | Pressure sensor | Diagnosis condition |
|
|
| Signal (terminal) | — | ||||
| Threshold | When a malfunction is detected in pressure sensor. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106C-17" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
STOP LAMP SWITCH SYSTEM
Check the stop lamp switch system. Refer to Component Function Check.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace stop lamp switch system.
CHECK BRAKE FLUID LEAKAGE
Check the brake fluid leakage. Refer to BRAKE FLUID : Inspection.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair or replace brake fluid leakage part.
CHECK BRAKE PIPING
Check the brake piping.
Front: Refer to FRONT BRAKE PIPING : Inspection.
Rear: Refer to REAR BRAKE PIPING : Inspection.
Is the inspection result normal?
YES>>GO TO 4.
NO>>Repair or replace error-detected brake piping.
Front: Refer to REAR BRAKE PIPING : Inspection.
Rear: Refer to REAR BRAKE PIPING : Removal & Installation.
CHECK BRAKE PEDAL
Check the brake pedal.
Brake pedal height: Refer to BRAKE PEDAL : Periodic Maintenance Operation.
Brake pedal assembly: Refer to BRAKE PEDAL : Inspection and Adjustment.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Adjust the brake pedal height or replace brake pedal assembly.
Adjust the brake pedal: Refer to BRAKE PEDAL : Periodic Maintenance Operation.
Replace the brake pedal: Refer to BRAKE PEDAL : Removal & Installation.
CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT
Check the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Inspection.
Is the inspection result normal?
YES>>GO TO 6.
NO>>Repair or replace electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.
CHECK FRONT DISC BRAKE
Check the front disc brake. Refer to FRONT BRAKE CALIPER ASSEMBLY : Inspection.
Is the inspection result normal?
YES>>GO TO 7.
NO>>Repair or replace front disc brake. Refer to FRONT BRAKE CALIPER ASSEMBLY : Removal & Installation.
CHECK REAR DISC BRAKE
Check the rear disc brake. Refer to REAR BRAKE CALIPER ASSEMBLY : Inspection.
Is the inspection result normal?
YES>>GO TO 8.
NO>>Repair or replace rear disc brake. Refer to REAR BRAKE CALIPER ASSEMBLY : Removal & Installation.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 9.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
PERFORM SELF-DIAGNOSIS
With CONSULT
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY, and drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106C-17” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>Check the ABS actuator and electric unit (control unit) harness connector and terminal for damage, looseness and disconnection. Repair / replace harness, connector, or terminal.
C106c-64 Pressure Sensor Nissan Ariya SUV
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C106C | 64 | Pressure sensor | Diagnosis condition |
|
|
| Signal (terminal) | — | ||||
| Threshold | When a malfunction is detected in pressure sensor. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106C-64" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
STOP LAMP SWITCH SYSTEM
Check the stop lamp switch system. Refer to Component Function Check.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace stop lamp switch system.
CHECK BRAKE FLUID LEAKAGE
Check the brake fluid leakage. Refer to BRAKE FLUID : Inspection.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair or replace brake fluid leakage part.
CHECK BRAKE PIPING
Check the brake piping.
Front: Refer to FRONT BRAKE PIPING : Inspection.
Rear: Refer to REAR BRAKE PIPING : Inspection.
Is the inspection result normal?
YES>>GO TO 4.
NO>>Repair or replace error-detected brake piping.
Front: Refer to REAR BRAKE PIPING : Inspection.
Rear: Refer to REAR BRAKE PIPING : Removal & Installation.
CHECK BRAKE PEDAL
Check the brake pedal.
Brake pedal height: Refer to BRAKE PEDAL : Periodic Maintenance Operation.
Brake pedal assembly: Refer to BRAKE PEDAL : Inspection and Adjustment.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Adjust the brake pedal height or replace brake pedal assembly.
Adjust the brake pedal: Refer to BRAKE PEDAL : Periodic Maintenance Operation.
Replace the brake pedal: Refer to BRAKE PEDAL : Removal & Installation.
CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT
Check the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Inspection.
Is the inspection result normal?
YES>>GO TO 6.
NO>>Repair or replace electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.
CHECK FRONT DISC BRAKE
Check the front disc brake. Refer to FRONT BRAKE CALIPER ASSEMBLY : Inspection.
Is the inspection result normal?
YES>>GO TO 7.
NO>>Repair or replace front disc brake. Refer to FRONT BRAKE CALIPER ASSEMBLY : Removal & Installation.
CHECK REAR DISC BRAKE
Check the rear disc brake. Refer to REAR BRAKE CALIPER ASSEMBLY : Inspection.
Is the inspection result normal?
YES>>GO TO 8.
NO>>Repair or replace rear disc brake. Refer to REAR BRAKE CALIPER ASSEMBLY : Removal & Installation.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 9.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
PERFORM SELF-DIAGNOSIS
With CONSULT
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Set the vehicle to READY, and drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106C-64” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>Check the ABS actuator and electric unit (control unit) harness connector and terminal for damage, looseness and disconnection. Repair / replace harness, connector, or terminal.
C106e-54 Steering Angle Sensor Nissan Ariya first Gen
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C106E | 54 | Steering angle sensor | Diagnosis condition |
|
|
| Signal (terminal) | — | ||||
| Threshold | When adjustment of steering angle sensor neutral position is not complete. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
| Incomplete adjustment of steering angle sensor |
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106E-54" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
ADJUST THE NEUTRAL POSITION OF STEERING ANGLE SENSOR
With CONSULT
Perform neutral position adjustment of steering angle sensor. Refer to Work Procedure.
>>GO TO 2.
PERFORM SELF-DIAGNOSIS
With CONSULT
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC "C106E-54" detected?
YES>>GO TO 3.
NO>>INSPECTION END
CHECK STEERING ANGLE SENSOR SYSTEM
Power switch OFF.
Check the steering angle sensor system.
C106E-55: Refer to DTC Diagnosis Procedure.
C106E-64: Refer to DTC Diagnosis Procedure.
C106F-54: Refer to DTC Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 4.
NO>>Repair / replace harness, connector, or terminal.
CHECK DATA MONITOR
With CONSULT
Select “ABS”, “Data monitor” and “Steering angle” according to this order.
Check that the indication changes with the steering angle when the steering wheel is turned left/right from the neutral position. Refer to Values On The Diagnosis Tool.
Is the inspection result normal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>Replace the steering angle sensor. Refer to STEERING ANGLE SENSOR : Removal & Installation.
C106e-55 Steering Angle Sensor Nissan Ariya 2023
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C106E | 55 | Steering angle sensor | Diagnosis condition |
|
|
| Signal (terminal) | CAN communication signal | ||||
| Threshold | When a malfunction is detected in steering angle sensor. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106E-55" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
ADJUST THE NEUTRAL POSITION OF STEERING ANGLE SENSOR
With CONSULT
Perform neutral position adjustment of steering angle sensor. Refer to Work Procedure.
>>GO TO 2.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC "C106E-55" detected?
YES>>GO TO 3.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the steering angle sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 4.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Connect 12V battery negative terminal.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC "C106E-55" detected?
YES-1>>“CRNT” is displayed: GO TO 5.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO>>INSPECTION END
STEERING ANGLE SENSOR POWER SUPPLY
Disconnect 12V battery negative terminal.
Disconnect steering angle sensor harness connector.
Connect 12V battery negative terminal.
Check the voltage between steering angle sensor harness connector and ground.
+ — Voltage Steering angle sensor Connector Terminal M122 8 Ground Approx. 0 V Power switch is ON.
Check the voltage between steering angle sensor harness connector and ground.
+ — Voltage Steering angle sensor Connector Terminal M122 8 Ground 10 - 16 V
Is the inspection result normal?
YES>>GO TO 8.
NO-1>>Without ProPILOT Assist 2.0: GO TO 6.
NO-2>>With ProPILPT Assist 2.0: GO TO 7.
STEERING ANGLE SENSOR POWER SUPPLY CIRCUIT (WITHOUT PROPILOT ASSIST2.0)
Disconnect 12V battery negative terminal.
Check the 5A fuse (#7).
Disconnect fuse block (J/B) harness connector.
Check the continuity between steering angle sensor harness connector and fuse block (J/B).
Steering angle sensor Fuse block (J/B) Continuity Connector Terminal Connector Terminal M122 8 M72 115 Existed Check the continuity between steering angle sensor harness connector and ground.
Steering angle sensor — Continuity Connector Terminal M122 8 Ground Not existed
Is the inspection result normal?
YES>>Perform trouble diagnosis for power switch ON power supply.
NO>>Repair / replace harness, connector, or fuse.
STEERING ANGLE SENSOR POWER SUPPLY CIRCUIT (WITH PROPILOT ASSIST 2.0)
Disconnect 12V battery negative terminal.
Check the 5A fuse (#118).
Check the continuity and short circuit between steering angle sensor harness connector terminal (8) and 5A fuse (#118).
Is the inspection result normal?
YES>>Perform trouble diagnosis for power switch ON power supply.
NO>>Repair / replace harness, connector, or fuse.
STEERING ANGLE SENSOR GROUND CIRCUIT
Check the continuity between steering angle sensor harness connector and ground.
| Steering angle sensor | — | Continuity | |
|---|---|---|---|
| Connector | Terminal | ||
| M122 | 5 | Ground | Existed |
Is the inspection result normal?
YES>>GO TO 9.
NO>>Repair / replace harness or connector.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 10.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
CHECK CAN COMMUNICATION LINE
Connect steering angle sensor harness connector.
Connect fuse block (J/B) harness connector. (Without Pro PILOT Assist 2.0)
Connect 12V battery negative terminal.
Check the CAN communication line. Refer to Trouble Diagnosis Flow Chart.
Is the inspection result normal?
YES>>GO TO 11.
NO>>Repair / replace harness or connector.
CHECK DATA MONITOR
With CONSULT
Select "ABS", "Data monitor" and "Steering angle" according to this order.
Check that the indication changes with steering angle when the steering wheel is turned left/right from the neutral position. Refer to Values On The Diagnosis Tool.
Is the inspection result normal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>Replace the steering angle sensor. Refer to STEERING ANGLE SENSOR : Removal & Installation.
C106e-64 Steering Angle Sensor Nissan Ariya
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C106E | 64 | Steering angle sensor | Diagnosis condition |
|
|
| Signal (terminal) | CAN communication signal | ||||
| Threshold | When a malfunction is detected in steering angle sensor. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106E-64" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
ADJUST THE NEUTRAL POSITION OF STEERING ANGLE SENSOR
With CONSULT
Perform neutral position adjustment of steering angle sensor. Refer to Work Procedure.
>>GO TO 2.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC "C106E-64" detected?
YES>>GO TO 3.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the steering angle sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 4.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Connect 12V battery negative terminal.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC "C106E-64" detected?
YES-1>>“CRNT” is displayed: GO TO 5.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO>>INSPECTION END
STEERING ANGLE SENSOR POWER SUPPLY
Disconnect 12V battery negative terminal.
Disconnect steering angle sensor harness connector.
Connect 12V battery negative terminal.
Check the voltage between steering angle sensor harness connector and ground.
+ — Voltage Steering angle sensor Connector Terminal M122 8 Ground Approx. 0 V Power switch is ON.
Check the voltage between steering angle sensor harness connector and ground.
+ — Voltage Steering angle sensor Connector Terminal M122 8 Ground 10 - 16 V
Is the inspection result normal?
YES>>GO TO 8.
NO-1>>Without ProPILOT Assist 2.0: GO TO 6.
NO-2>>With ProPILOT Assist 2.0: GO TO 7.
STEERING ANGLE SENSOR POWER SUPPLY CIRCUIT (WITHOUT PROPILOT ASSIST 2.0)
Disconnect 12V battery negative terminal.
Check the 5A fuse (#7).
Disconnect fuse block (J/B) harness connector.
Check the continuity between steering angle sensor harness connector and fuse block (J/B).
Steering angle sensor Fuse block (J/B) Continuity Connector Terminal Connector Terminal M122 8 M72 115 Existed Check the continuity between steering angle sensor harness connector and ground.
Steering angle sensor — Continuity Connector Terminal M122 8 Ground Not existed
Is the inspection result normal?
YES>>Perform trouble diagnosis for power switch ON power supply.
NO>>Repair / replace harness, connector, or fuse.
STEERING ANGLE SENSOR POWER SUPPLY CIRCUIT (WITH PROPILOT ASSIST 2.0)
Disconnect 12V battery negative terminal.
Check the 5A fuse (#118).
Check the continuity and short circuit between steering angle sensor harness connector terminal (8) and 5A fuse (#118).
Is the inspection result normal?
YES>>Perform trouble diagnosis for power switch ON power supply.
NO>>Repair / replace harness, connector, or fuse.
STEERING ANGLE SENSOR GROUND CIRCUIT
Check the continuity between steering angle sensor harness connector and ground.
| Steering angle sensor | — | Continuity | |
|---|---|---|---|
| Connector | Terminal | ||
| M122 | 5 | Ground | Existed |
Is the inspection result normal?
YES>>GO TO 9.
NO>>Repair / replace harness or connector.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 10.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
CHECK CAN COMMUNICATION LINE
Connect steering angle sensor harness connector.
Connect fuse block (J/B) harness connector. (Without ProPILOT Assist 2.0)
Connect 12V battery negative terminal.
Check the CAN communication line. Refer to Trouble Diagnosis Flow Chart.
Is the inspection result normal?
YES>>GO TO 11.
NO>>Repair / replace harness or connector.
CHECK DATA MONITOR
With CONSULT
Select "ABS", "Data monitor" and "Steering angle" according to this order.
Check that the indication changes with steering angle when the steering wheel is turned left/right from the neutral position. Refer to Values On The Diagnosis Tool.
Is the inspection result normal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>Replace the steering angle sensor. Refer to STEERING ANGLE SENSOR : Removal & Installation.
C106f-54 Steering Angle Sensor Nissan Ariya 2023
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C106F | 54 | Steering angle sensor | Diagnosis condition |
|
|
| Signal (terminal) | CAN communication signal | ||||
| Threshold | When a malfunction is detected in steering angle sensor. | ||||
| Diagnosis delay time | 2 seconds or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C106F-54" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
ADJUST THE NEUTRAL POSITION OF STEERING ANGLE SENSOR
With CONSULT
Perform neutral position adjustment of steering angle sensor. Refer to Work Procedure.
>>GO TO 2.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC "C106F-54" detected?
YES>>GO TO 3.
NO>>INSPECTION END
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the steering angle sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 4.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Connect 12V battery negative terminal.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC "C106F-54" detected?
YES-1>>“CRNT” is displayed: GO TO 5.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO>>INSPECTION END
STEERING ANGLE SENSOR POWER SUPPLY
Disconnect 12V battery negative terminal.
Disconnect steering angle sensor harness connector.
Connect 12V battery negative terminal.
Check the voltage between steering angle sensor harness connector and ground.
+ — Voltage Steering angle sensor Connector Terminal M122 8 Ground Approx. 0 V Power switch is ON.
Check the voltage between steering angle sensor harness connector and ground.
+ — Voltage Steering angle sensor Connector Terminal M122 8 Ground 10 - 16 V
Is the inspection result normal?
YES>>GO TO 8.
NO-1>>Without ProPILOT Assist 2.0: GO TO 6.
NO-2>>With ProPILOT Assist 2.0: GO TO 7.
STEERING ANGLE SENSOR POWER SUPPLY CIRCUIT (WITHOUT PROPILOT ASSIST 2.0)
Disconnect 12V battery negative terminal.
Check the 5A fuse (#7).
Disconnect fuse block (J/B) harness connector.
Check the continuity between steering angle sensor harness connector and fuse block (J/B).
Steering angle sensor Fuse block (J/B) Continuity Connector Terminal Connector Terminal M122 8 M72 115 Existed Check the continuity between steering angle sensor harness connector and ground.
Steering angle sensor — Continuity Connector Terminal M122 8 Ground Not existed
Is the inspection result normal?
YES>>Perform trouble diagnosis for power switch ON power supply.
NO>>Repair / replace harness, connector, or fuse.
STEERING ANGLE SENSOR POWER SUPPLY CIRCUIT (WITH PROPILOT ASSIST 2.0)
Disconnect 12V battery negative terminal
Check the 5A fuse (#118).
Check the continuity and short circuit between steering angle sensor harness connector terminal (8) and 5A fuse (#118).
Is the inspection result normal?
YES>>Perform trouble diagnosis for power switch ON power supply.
NO>>Repair / replace harness, connector, or fuse.
STEERING ANGLE SENSOR GROUND CIRCUIT
Check the continuity between steering angle sensor harness connector and ground.
| Steering angle sensor | — | Continuity | |
|---|---|---|---|
| Connector | Terminal | ||
| M122 | 5 | Ground | Existed |
Is the inspection result normal?
YES>>GO TO 9.
NO>>Repair / replace harness or connector.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 10.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
CHECK CAN COMMUNICATION LINE
Connect steering angle sensor harness connector.
Connect fuse block (J/B) harness connector. (Without ProPILOT Assist 2.0)
Connect 12V battery negative terminal.
Check the CAN communication line. Refer to Trouble Diagnosis Flow Chart.
Is the inspection result normal?
YES>>GO TO 11.
NO>>Repair / replace harness or connector.
CHECK DATA MONITOR
With CONSULT
Select "ABS", "Data monitor" and "Steering angle" according to this order.
Check that the indication changes with steering angle when the steering wheel is turned left/right from the neutral position. Refer to Values On The Diagnosis Tool.
Is the inspection result normal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>Replace the steering angle sensor. Refer to STEERING ANGLE SENSOR : Removal & Installation.
C1070-01 Side G Sensor Nissan Ariya 2023
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1070 | 01 | Side G sensor | Diagnosis condition |
|
|
| Signal (terminal) | — | ||||
| Threshold | When a malfunction is detected in side G sensor. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1070-01" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK SELF-DIAGNOSIS RESULTS
With CONSULT
Replace the ABS actuator and electric unit (control unit) even if other DTCs are displayed along with “C1070-01” in self-diagnosis for “ABS”.
>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
C1070-54 Side G Sensor Nissan Ariya
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1070 | 54 | Side G sensor | Diagnosis condition |
|
|
| Signal (terminal) | — | ||||
| Threshold | When calibration of yaw rate/side/ decel G sensor is not complete. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
| Incomplete calibration of side yaw rate/side/decel G sensor |
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1070-54" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CALIBRATION OF SIDE G SENSOR
Perform calibration of side G sensor. Refer to DTC Diagnosis Procedure.
>>GO TO 2.
PERFORM SELF-DIAGNOSIS
With CONSULT
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC "C1070-54" detected?
YES>>Check the DTC.
NO>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
C1070-64 Side G Sensor Nissan Ariya 2026
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1070 | 64 | Side G sensor | Diagnosis condition |
|
|
| Signal (terminal) | — | ||||
| Threshold | When a malfunction is detected in side G sensor. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1070-64" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK SELF-DIAGNOSIS RESULTS
With CONSULT
Replace the ABS actuator and electric unit (control unit) even if other DTCs are displayed along with “C1070-64” in self-diagnosis for “ABS”.
>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
C1071-54 Decel G Sensor Nissan Ariya 2026
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1071 | 54 | Decel G sensor | Diagnosis condition |
|
|
| Signal (terminal) | — | ||||
| Threshold | When calibration of yaw rate/side/ decel G sensor is not complete. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1071-54" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CALIBRATION OF SIDE G SENSOR
Perform calibration of side G sensor. Refer toDTC Diagnosis Procedure.
>>GO TO 2.
PERFORM SELF-DIAGNOSIS
With CONSULT
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC "C1071-54" detected?
YES>>Check the DTC.
NO>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
C1071-61 Decel G Sensor Nissan Ariya 2023
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1071 | 61 | Decel G sensor | Diagnosis condition |
|
|
| Signal (terminal) | — | ||||
| Threshold | When a malfunction is detected in decel G sensor. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1071-61" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK SELF-DIAGNOSIS RESULTS
With CONSULT
Replace the ABS actuator and electric unit (control unit) even if other DTCs are displayed along with “C1071-61” in self-diagnosis for “ABS”.
>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
C1071-64 Decel G Sensor Nissan Ariya SUV
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1071 | 64 | Decel G sensor | Diagnosis condition |
|
|
| Signal (terminal) | — | ||||
| Threshold | When a malfunction is detected in decel G sensor. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1071-64" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK SELF-DIAGNOSIS RESULTS
With CONSULT
Replace the ABS actuator and electric unit (control unit) even if other DTCs are displayed along with “C1071-64” in self-diagnosis for “ABS”.
>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
C1072-01 Yaw Rate Sensor Nissan Ariya
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1072 | 01 | Yaw rate sensor | Diagnosis condition |
|
|
| Signal (terminal) | — | ||||
| Threshold | When a malfunction is detected in yaw rate sensor. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1072-01" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK SELF-DIAGNOSIS RESULTS
With CONSULT
Replace the ABS actuator and electric unit (control unit) even if other DTCs are displayed along with “C1072-01” in self-diagnosis for “ABS”.
>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
C1072-64 Yaw Rate Sensor Nissan Ariya 1st generation
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1072 | 64 | Yaw rate sensor | Diagnosis condition |
|
|
| Signal (terminal) | — | ||||
| Threshold | When a malfunction is detected in yaw rate sensor. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1072-64" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK SELF-DIAGNOSIS RESULTS
With CONSULT
Replace the ABS actuator and electric unit (control unit) even if other DTCs are displayed along with “C1072-64” in self-diagnosis for “ABS”.
>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
C1072-83 Yaw Rate Sensor Nissan Ariya SUV
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1072 | 83 | Yaw rate sensor | Diagnosis condition |
|
|
| Signal (terminal) | — | ||||
| Threshold | When a malfunction is detected in yaw rate sensor. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1072-83" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK SELF-DIAGNOSIS RESULTS
With CONSULT
Replace the ABS actuator and electric unit (control unit) even if other DTCs are displayed along with “C1072-83” in self-diagnosis for “ABS”.
>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
C1076-55 Control Unit Nissan Ariya: FE0
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1076 | 55 | Not configured | Diagnosis condition |
|
|
| Signal (terminal) | — | ||||
| Threshold | When programing is not complete. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
| Programing is not complete |
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
ABS function
EBD function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1076-55" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
PERFORM PROGRAMING
Perform programming of ABS actuator and electric unit (control unit). Refer to Work Procedure.
>>GO TO 2.
PERFORM SELF-DIAGNOSIS
With CONSULT
Replace the ABS actuator and electric unit (control unit) even if other DTCs are displayed along with “C1076-55” in self-diagnosis for “ABS”.
>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
C1077-55 Control Unit Nissan Ariya 2023
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1077 | 55 | Downhill drive support switch | Diagnosis condition |
|
|
| Signal (terminal) | — | ||||
| Threshold | When an internal malfunction in ABS actuator and electric unit (control unit). | ||||
| Diagnosis delay time | 2 seconds or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1077-55" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK VCM SYSTEM
With CONSULT
Perform self-diagnosis for “EV/HEV”.
Is DTC detected?
YES>>Check the DTC. Refer to DTC Index.
>>GO TO 2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
CHECK CONNECTOR AND TERMINAL
Disconnect 12V battery negative terminal.
Disconnect VCM harness connector.
Check the VCM harness connector for disconnection or looseness.
Check the VCM terminals for damage or loose connection with harness connector.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 4.
NO>>Repair / replace harness, connector, or terminal. GO TO 4.
PERFORM SELF-DIAGNOSIS
With CONSULT
Connect VCM harness connector.
Connect ABS actuator and electric unit (control unit) harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC detected?
YES>>Check the DTC. Refer to DTC Index.
NO>>INSPECTION END
C1077-92 Control Unit Nissan Ariya SUV
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1077 | 92 | Downhill drive support switch | Diagnosis condition |
|
|
| Signal (terminal) | CAN communication signal | ||||
| Threshold | When a malfunction is detected in shift position. | ||||
| Diagnosis delay time | 2 seconds or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
Normal control
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1077-92" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK VCM SYSTEM
With CONSULT
Perform self-diagnosis for “EV/HEV”.
Is DTC detected?
YES>>Check the DTC. Refer to DTC Index.
>>GO TO 2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
CHECK CONNECTOR AND TERMINAL
Disconnect 12V battery negative terminal.
Disconnect VCM harness connector.
Check the VCM harness connector for disconnection or looseness.
Check the VCM terminals for damage or loose connection with harness connector.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 4.
NO>>Repair / replace harness, connector, or terminal. GO TO 4.
PERFORM SELF-DIAGNOSIS
With CONSULT
Connect VCM harness connector.
Connect ABS actuator and electric unit (control unit) harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC detected?
YES>>Check the DTC. Refer to DTC Index.
NO>>INSPECTION END
C1078-55 Control Unit Nissan Ariya
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1078 | 55 | Not configuration | Diagnosis condition |
|
|
| Signal (terminal) | — | ||||
| Threshold | When configuration is not complete. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
| Configuration is not complete |
|
FAIL-SAFE
The following functions are suspended.
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1078-55" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
PERFORM CONFIGURATION
Perform configuration of ABS actuator and electric unit (control unit). Refer to Work Procedure.
>>GO TO 2.
CHECK SELF-DIAGNOSIS RESULTS
With CONSULT
Replace the ABS actuator and electric unit (control unit) even if other DTCs are displayed along with “C1078-55” in self-diagnosis for “ABS”.
>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
C1079-55 Control Unit Nissan Ariya SUV
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1079 | 55 | Not configuration | Diagnosis condition |
|
|
| Signal (terminal) | — | ||||
| Threshold | When configuration is not complete. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
| Configuration is not complete |
|
FAIL-SAFE
Normal control
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1079-55" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
PERFORM CONFIGURATION
Perform configuration of ABS actuator and electric unit (control unit). Refer to Work Procedure.
>>GO TO 2.
CHECK SELF-DIAGNOSIS RESULTS
With CONSULT
Replace the ABS actuator and electric unit (control unit) even if other DTCs are displayed along with “C1079-55” in self-diagnosis for “ABS”.
>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
C107a-55 Control Unit Nissan Ariya SUV
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C107A | 55 | Not configuration | Diagnosis condition |
|
|
| Signal (terminal) | — | ||||
| Threshold | When configuration is not complete. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
| Configuration is not complete |
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C107A-55" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
PERFORM CONFIGURATION
Perform configuration of ABS actuator and electric unit (control unit). Refer to Work Procedure.
>>GO TO 2.
CHECK SELF-DIAGNOSIS RESULTS
With CONSULT
Replace the ABS actuator and electric unit (control unit) even if other DTCs are displayed along with “C107A-55” in self-diagnosis for “ABS”.
>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
C107b-53 Vdc Function Nissan Ariya 2026
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C107B | 53 | Nissan Ariya Vehicle dynamics control function | Diagnosis condition |
|
|
| Signal (terminal) | — | ||||
| Threshold | When configuration is not complete. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
| Configuration is not complete |
|
FAIL-SAFE
Normal control
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C107B-53" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
PERFORM CONFIGURATION
Perform configuration of ABS actuator and electric unit (control unit). Refer to Work Procedure.
>>GO TO 2.
CHECK SELF-DIAGNOSIS RESULTS
With CONSULT
Replace the ABS actuator and electric unit (control unit) even if other DTCs are displayed along with “C107B-53” in self-diagnosis for “ABS”.
>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
C107c-53 Control Unit Nissan Ariya 1st generation
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C107C | 53 | Not configuration | Diagnosis condition |
|
|
| Signal (terminal) | — | ||||
| Threshold | When configuration is not complete. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
| Configuration is not complete |
|
FAIL-SAFE
Normal control
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C107C-53" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
PERFORM CONFIGURATION
Perform configuration of ABS actuator and electric unit (control unit). Refer to Work Procedure.
>>GO TO 2.
CHECK SELF-DIAGNOSIS RESULTS
With CONSULT
Replace the ABS actuator and electric unit (control unit) even if other DTCs are displayed along with “C107C-53” in self-diagnosis for “ABS”.
>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
C1080-86 Vcm System Nissan Ariya
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1080 | 86 | ECM | Diagnosis condition |
|
|
| Signal (terminal) | — | ||||
| Threshold | When a malfunction is detected in VCM system. | ||||
| Diagnosis delay time | 2 seconds or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1080-86" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK VCM SYSTEM
With CONSULT
Perform self-diagnosis for “EV/HEV”.
Is DTC detected?
YES>>Check the DTC. Refer to DTC Index.
NO>>GO TO 2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
CHECK CONNECTOR AND TERMINAL
Disconnect 12V battery negative terminal.
Disconnect VCM harness connector.
Check the VCM harness connector for disconnection or looseness.
Check the VCM terminals for damage or loose connection with harness connector.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 4.
NO>>Repair / replace harness, connector, or terminal, securely lock the connector. GO TO 4.
PERFORM SELF-DIAGNOSIS
With CONSULT
Connect VCM harness connector.
Connect ABS actuator and electric unit (control unit) harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC detected?
YES>>Check the DTC. Refer to DTC Index.
NO>>INSPECTION END
C1082-86 Vcm System Nissan Ariya
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1082 | 86 | CAN communication error (TCM) | Diagnosis condition |
|
|
| Signal (terminal) | — | ||||
| Threshold | When a malfunction is detected in VCM system. | ||||
| Diagnosis delay time | 2 seconds or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1082-86" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK VCM SYSTEM
With CONSULT
Perform self-diagnosis for “EV/HEV”.
Is DTC detected?
YES>>Check the DTC. Refer to DTC Index.
NO>>GO TO 2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
CHECK CONNECTOR AND TERMINAL
Disconnect 12V battery negative terminal.
Disconnect VCM harness connector.
Check the VCM harness connector for disconnection or looseness.
Check the VCM terminals for damage or loose connection with harness connector.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 4.
NO>>Repair / replace harness, connector, or terminal, securely lock the connector. GO TO 4.
PERFORM SELF-DIAGNOSIS
With CONSULT
Connect VCM harness connector.
Connect ABS actuator and electric unit (control unit) harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC detected?
YES>>Check the DTC. Refer to DTC Index.
NO>>INSPECTION END
C1083-86 Steering Angle Sensor System Nissan Ariya first Gen
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1083 | 86 | Steering angle sensor | Diagnosis condition |
|
|
| Signal (terminal) | CAN communication signal | ||||
| Threshold | When a malfunction is detected in steering angle sensor. | ||||
| Diagnosis delay time | 2 seconds or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1083-86" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK STEERING ANGLE SENSOR SYSTEM
With CONSULT
Perform self-diagnosis for “ABS”.
Is DTC detected?
YES>>Check the DTC. Refer to DTC Index.
NO>>GO TO 2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
CHECK CONNECTOR AND TERMINAL
Disconnect 12V battery negative terminal.
Disconnect steering angle sensor harness connector.
Check the steering angle sensor harness connector for disconnection or looseness.
Check the steering angle sensor terminals for damage or loose connection with harness connector.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 4.
NO>>Repair / replace harness, connector, or terminal, securely lock the connector. GO TO 4.
PERFORM SELF-DIAGNOSIS
With CONSULT
Connect steering angle sensor harness connector.
Connect ABS actuator and electric unit (control unit) harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC detected?
YES>>Check the DTC. Refer to DTC Index.
NO>>INSPECTION END
C1085-86 Combination Meter System Nissan Ariya: FE0
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1085 | 86 | Combination meter | Diagnosis condition |
|
|
| Signal (terminal) | CAN communication signal | ||||
| Threshold | When a malfunction is detected in combination meter system. | ||||
| Diagnosis delay time | 2 seconds or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1085-86" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK COMBINATION METER SYSTEM
With CONSULT
Perform self-diagnosis for “COMBINATION METER”.
Is DTC detected?
YES>>Check the DTC. Refer to DTC Index.
NO>>GO TO 2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
CHECK CONNECTOR AND TERMINAL
Disconnect 12V battery negative terminal.
Disconnect combination meter harness connector.
Check the combination meter harness connector for disconnection or looseness.
Check the combination meter terminals for damage or loose connection with harness connector.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 4.
NO>>Repair / replace harness, connector, or terminal, securely lock the connector. GO TO 4.
PERFORM SELF-DIAGNOSIS
With CONSULT
Connect combination meter harness connector.
Connect ABS actuator and electric unit (control unit) harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC detected?
YES>>Check the DTC. Refer to DTC Index.
NO>>INSPECTION END
C1086-86 Bcm System Nissan Ariya SUV
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1086 | 86 | CAN communication error (BCM) | Diagnosis condition |
|
|
| Signal (terminal) | CAN communication signal | ||||
| Threshold | When a malfunction is detected in BCM system. | ||||
| Diagnosis delay time | 2 seconds or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1086-86" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK BCM SYSTEM
With CONSULT
Perform self-diagnosis for “BCM”.
Is DTC detected?
YES>>Check the DTC. Refer to DTC Index.
NO>>GO TO 2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
CHECK CONNECTOR AND TERMINAL
Disconnect 12V battery negative terminal.
Disconnect BCM harness connector.
Check the BCM harness connector for disconnection or looseness.
Check the BCM terminals for damage or loose connection with harness connector.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 4.
NO>>Repair / replace harness, connector, or terminal, securely lock the connector. GO TO 4.
PERFORM SELF-DIAGNOSIS
With CONSULT
Connect BCM harness connector.
Connect ABS actuator and electric unit (control unit) harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC detected?
YES>>Check the DTC. Refer to DTC Index.
NO>>INSPECTION END
C1087-86 Ipdm E/r System Nissan Ariya 1st generation
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1087 | 86 | Intelligent power distribution module engine room | Diagnosis condition |
|
|
| Signal (terminal) | CAN communication signal | ||||
| Threshold | When a malfunction is detected in IPDM E/R system. | ||||
| Diagnosis delay time | 2 seconds or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1087-86" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK IPDM E/R SYSTEM
With CONSULT
Perform self-diagnosis for “IPDM E/R”.
Is DTC detected?
YES>>Check the DTC. Refer to DTC Index.
NO>>GO TO 2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
CHECK CONNECTOR AND TERMINAL
Disconnect 12V battery negative terminal.
Disconnect IPDM E/R harness connector.
Check the IPDM E/R harness connector for disconnection or looseness.
Check the IPDM E/R terminals for damage or loose connection with harness connector.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 4.
NO>>Repair / replace harness, connector, or terminal, securely lock the connector. GO TO 4.
PERFORM SELF-DIAGNOSIS
With CONSULT
Connect IPDM E/R harness connector.
Connect ABS actuator and electric unit (control unit) harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC detected?
YES>>Check the DTC. Refer to DTC Index.
NO>>INSPECTION END
C1088-86 Av System Nissan Ariya SUV
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1088 | 86 | AV system | Diagnosis condition |
|
|
| Signal (terminal) | CAN communication signal | ||||
| Threshold | When a malfunction is detected in AV control unit system. | ||||
| Diagnosis delay time | 2 seconds or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
Normal control
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1088-86" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK AV CONTROL UNIT SYSTEM
With CONSULT
Perform self-diagnosis for “MULTI AV”.
Is DTC detected?
YES>>Check the DTC. Refer to DTC Index.
NO>>GO TO 2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
CHECK CONNECTOR AND TERMINAL
Disconnect 12V battery negative terminal.
Disconnect AV control unit harness connector.
Check the AV control unit harness connector for disconnection or looseness.
Check the AV control unit terminals for damage or loose connection with harness connector.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 4.
NO>>Repair / replace harness, connector, or terminal, securely lock the connector. GO TO 4.
PERFORM SELF-DIAGNOSIS
With CONSULT
Connect AV control unit harness connector.
Connect ABS actuator and electric unit (control unit) harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC detected?
YES>>Check the DTC. Refer to DTC Index.
NO>>INSPECTION END
C1090-86 Adas Control Unit System Nissan Ariya 1st generation
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1090 | 86 | ADAS control unit | Diagnosis condition |
|
|
| Signal (terminal) | CAN communication signal | ||||
| Threshold | When a malfunction is detected in ADAS control unit 2 system. | ||||
| Diagnosis delay time | 2 seconds or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
Normal control
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1090-86" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK ADAS CONTROL UNIT 2 SYSTEM
With CONSULT
Perform self-diagnosis for “ICC/ADAS 2”.
Is DTC detected?
YES>>Check the DTC. Refer to DTC Index.
NO>>GO TO 2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
CHECK CONNECTOR AND TERMINAL
Disconnect 12V battery negative terminal.
Disconnect ADAS control unit 2 harness connector.
Check the ADAS control unit 2 harness connector for disconnection or looseness.
Check the ADAS control unit 2 terminals for damage or loose connection with harness connector.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 4.
NO>>Repair / replace harness, connector, or terminal, securely lock the connector. GO TO 4.
PERFORM SELF-DIAGNOSIS
With CONSULT
Connect ADAS control unit 2 harness connector.
Connect ABS actuator and electric unit (control unit) harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC detected?
YES>>Check the DTC. Refer to DTC Index.
NO>>INSPECTION END
C1092-86 4wd/awd System Nissan Ariya: FE0
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1092 | 86 | 4WD/AWD control unit | Diagnosis condition |
|
|
| Signal (terminal) | CAN communication signal | ||||
| Threshold | When a malfunction is detected in VCM system. | ||||
| Diagnosis delay time | 2 seconds or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1092-86" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK VCM SYSTEM
With CONSULT
Perform self-diagnosis for “EV/HEV”.
Is DTC detected?
YES>>Check the DTC. Refer to DTC Index.
NO>>GO TO 2 .
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3 .
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
CHECK CONNECTOR AND TERMINAL
Disconnect 12V battery negative terminal.
Disconnect VCM harness connector.
Check the VCM harness connector for disconnection or looseness.
Check the VCM terminals for damage or loose connection with harness connector.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 4 .
NO>>Repair / replace harness, connector, or terminal, securely lock the connector. GO TO 4 .
PERFORM SELF-DIAGNOSIS
With CONSULT
Connect VCM harness connector.
Connect ABS actuator and electric unit (control unit) harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC detected?
YES>>Check the DTC. Refer to DTC Index.
NO>>INSPECTION END
C1094-86 Vcm System Nissan Ariya first Gen
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1094 | 86 | VCM/ECM | Diagnosis condition |
|
|
| Signal (terminal) | CAN communication signal | ||||
| Threshold | When a malfunction is detected in VCM system. | ||||
| Diagnosis delay time | 2 seconds or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1094-86" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK VCM SYSTEM
With CONSULT
Perform self-diagnosis for “EV/HEV”.
Is DTC detected?
YES>>Check the DTC. Refer to DTC Index.
NO>>GO TO 2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
CHECK CONNECTOR AND TERMINAL
Disconnect 12V battery negative terminal.
Disconnect VCM harness connector.
Check the VCM harness connector for disconnection or looseness.
Check the VCM terminals for damage or loose connection with harness connector.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 4.
NO>>Repair / replace harness, connector, or terminal, securely lock the connector. GO TO 4.
PERFORM SELF-DIAGNOSIS
With CONSULT
Connect VCM harness connector.
Connect ABS actuator and electric unit (control unit) harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC detected?
YES>>Check the DTC. Refer to DTC Index.
NO>>INSPECTION END
C1095-86 Vcm System Nissan Ariya 1st generation
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1095 | 86 | Electrically-driven intelligent brake unit | Diagnosis condition |
|
|
| Signal (terminal) | CAN communication signal | ||||
| Threshold | When a malfunction is detected in electrically-driven intelligent brake unit system. | ||||
| Diagnosis delay time | 2 seconds or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
Brake limited slip differential (BLSD) function
Brake force distribution function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1095-86" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT SYSTEM
With CONSULT
Perform self-diagnosis for “BRAKE”.
Is DTC detected?
YES>>Check the DTC. Refer to DTC Index.
NO>>GO TO 2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
CHECK CONNECTOR AND TERMINAL
Disconnect 12V battery negative terminal.
Disconnect electrically-driven intelligent brake unit harness connector.
Check the electrically-driven intelligent brake unit harness connector for disconnection or looseness.
Check the electrically-driven intelligent brake unit terminals for damage or loose connection with harness connector.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 4.
NO>>Repair / replace harness, connector, or terminal, securely lock the connector. GO TO 4.
PERFORM SELF-DIAGNOSIS
With CONSULT
Connect electrically-driven intelligent brake unit harness connector.
Connect ABS actuator and electric unit (control unit) harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC detected?
YES>>Check the DTC. Refer to DTC Index.
NO>>INSPECTION END
C1096-86 Chassis Control System Nissan Ariya
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1096 | 86 | Chassis control module | Diagnosis condition |
|
|
| Signal (terminal) | CAN communication signal | ||||
| Threshold | When a malfunction is detected in chassis control module system. | ||||
| Diagnosis delay time | 2 seconds or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
hill start assist function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1096-86" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK CHASSIS CONTROL MODULE SYSTEM
With CONSULT
Perform self-diagnosis for “CHASSIS CONTROL”.
Is DTC detected?
YES>>Check the DTC. Refer to DTC Index.
NO>>GO TO 2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
CHECK CONNECTOR AND TERMINAL
Disconnect 12V battery negative terminal.
Disconnect chassis control module harness connector.
Check the chassis control module harness connector for disconnection or looseness.
Check the chassis control module terminals for damage or loose connection with harness connector.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 4.
NO>>Repair / replace harness, connector, or terminal, securely lock the connector. GO TO 4.
PERFORM SELF-DIAGNOSIS
With CONSULT
Connect chassis control module harness connector.
Connect ABS actuator and electric unit (control unit) harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC detected?
YES>>Check the DTC. Refer to DTC Index.
NO>>INSPECTION END
C1098-86 Avm System Nissan Ariya
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C1098 | 86 | AVM | Diagnosis condition |
|
|
| Signal (terminal) | CAN communication signal | ||||
| Threshold | When a malfunction is detected in around view control unit system. | ||||
| Diagnosis delay time | 2 seconds or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
Normal control
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C1098-86" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK AROUND VIEW MONITOR CONTROL UNIT SYSTEM
With CONSULT
Perform self-diagnosis for “AROUND VIEW MONITOR”.
Is DTC detected?
YES>>Check the DTC. Refer to DTC Index.
NO>>GO TO 2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
CHECK CONNECTOR AND TERMINAL
Disconnect 12V battery negative terminal.
Disconnect around view monitor control unit harness connector.
Check the around view monitor control unit harness connector for disconnection or looseness.
Check the around view monitor control unit terminals for damage or loose connection with harness connector.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 4.
NO>>Repair / replace harness, connector, or terminal, securely lock the connector. GO TO 4.
PERFORM SELF-DIAGNOSIS
With CONSULT
Connect around view monitor control unit harness connector.
Connect ABS actuator and electric unit (control unit) harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC detected?
YES>>Check the DTC. Refer to DTC Index.
NO>>INSPECTION END
C10aa-63 Pump Motor Nissan Ariya: FE0
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C10AA | 63 | Pump motor | Diagnosis condition |
|
|
| Signal (terminal) | — | ||||
| Threshold | When a malfunction is detected in motor or motor relay. | ||||
| Diagnosis delay time | 12 seconds or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
Normal control
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C10AA-63" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 2.
PERFORM SELF-DIAGNOSIS
With CONSULT
Connect 12V battery negative terminal.
Drive the Nissan Ariya vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC "C10AA-63" detected?
YES>>GO TO 3.
NO>>INSPECTION END
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 4.
ERASE SELF-DIAGNOSIS RESULT (1)
With CONSULT
Drive the Nissan Ariya vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
INSPECTION END
CHECK TERMINAL
Disconnect 12V battery negative terminal.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>Repair / replace harness, connector, or terminal. GO TO 6.
ERASE SELF-DIAGNOSIS RESULT (2)
With CONSULT
Connect ABS actuator and electric unit (control unit) harness connector.
Connect 12V battery negative terminal.
Drive the Nissan Ariya vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
INSPECTION END
C10ac-54 G Sensor Nissan Ariya SUV
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C10AC | 54 | Calibration incomplete | Diagnosis condition |
|
|
| Signal (terminal) | — | ||||
| Threshold | When calibration of yaw rate/side/ decel G sensor is not complete. | ||||
| Diagnosis delay time | 2 seconds or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
| Incomplete calibration of side yaw rate/side/decel G sensor |
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C10AC-54" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CALIBRATION OF SIDE G SENSOR
Perform calibration of side G sensor. Refer to DTC Diagnosis Procedure.
>>GO TO 2.
PERFORM SELF-DIAGNOSIS
With CONSULT
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC "C10AC-54" detected?
YES>>Check the DTC.
NO>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
C10ad-04 Brake Backup Function Nissan Ariya
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C10AD | 04 | Brake backup function | Diagnosis condition |
|
|
| Signal (terminal) | CAN communication signal | ||||
| Threshold | When a malfunction in incress backup function by ABS is detected. (When a malfunction is detected in electrically-driven intelligent brake unit system.) | ||||
| Diagnosis delay time | 2 seconds or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
Normal control
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C10AD-04" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT SYSTEM
With CONSULT
Perform self-diagnosis for “BRAKE”.
Is DTC detected?
YES>>Check the DTC. Refer to DTC Index.
NO>>GO TO 2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
CHECK CONNECTOR AND TERMINAL
Disconnect 12V battery negative terminal.
Disconnect electrically-driven intelligent brake unit harness connector.
Check the electrically-driven intelligent brake unit harness connector for disconnection or looseness.
Check the electrically-driven intelligent brake unit terminals for damage or loose connection with harness connector.
Disconnect ABS actuator and electric unit (control unit) harness connector.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 4.
NO>>Repair / replace harness, connector, or terminal, securely lock the connector. GO TO 4.
PERFORM SELF-DIAGNOSIS
With CONSULT
Connect electrically-driven intelligent brake unit harness connector.
Connect ABS actuator and electric unit (control unit) harness connector.
Connect 12V battery negative terminal.
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC detected?
YES>>Check the DTC. Refer to DTC Index.
NO>>INSPECTION END
C10af-01 Pressure Sensor Nissan Ariya first Gen
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C10AF | 01 | Pressure sensor | Diagnosis condition |
|
|
| Signal (terminal) | — | ||||
| Threshold | When a malfunction is detected in pressure sensor. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
Normal control
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “C10AF-01" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK STOP LAMP SWITCH SYSTEM
Check the stop lamp switch system. Refer to DTC Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace stop lamp switch system.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
PERFORM SELF-DIAGNOSIS
With CONSULT
Erase self-diagnosis result for “ABS”.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.
Stop the Nissan Ariya vehicle.
Power switch OFF (Auto ACC function ON).
Get out of the vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC "C10AF-01" detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>Check the ABS actuator and electric unit (control unit) harness connector and terminal for damage, looseness and disconnection. Repair / replace harness, connector, or terminal.
C10b0-01 Parking Brake Actuator (rh) Nissan Ariya 2026
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C10B0 | 01 | Parking brake actuator (right) | Diagnosis condition | When parking brake is apply or release. | |
| Signal (terminal) | — | ||||
| Threshold | When an open circuit is detected in motor of parking brake actuator (RH). | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Push the parking brake switch.
Pull the parking brake switch.
Perform self-diagnosis for “ABS”.
Is DTC “C10B0-01" detected?
YES-1>>“CRNT” is displayed (only "C10B0-01"): Refer to DTC Diagnosis Procedure.
YES-2>>“CRNT” is displayed ("C10B0-01" and "C10B0-09): Refer to DTC Diagnosis Procedure.
YES-3>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the parking brake actuator (RH) harness connector for disconnection or looseness.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair / replace harness or connector. GO TO 2.
CHECK PARKING BRAKE ACTUATOR CIRCUIT (1)
Disconnect the ABS actuator and electric unit (control unit) harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector terminals.
ABS actuator and electric unit (control unit) Continuity Connector Terminal B2 2 - 3 Existed
Is the inspection result normal?
YES>>GO TO 4.
NO>>GO TO 3.
CHECK PARKING BRAKE ACTUATOR CIRCUIT (2)
Check the continuity between parking brake actuator (RH) harness connector terminals.
| Terminal | Continuity |
|---|---|
| 1 - 2 | Existed |
Is the inspection result normal?
YES>>Repair / replace harness or connector.
NO>>Replace the parking brake actuator (RH). Refer to PARKING BRAKE ACTUATOR : Removal & Installation.
CHECK MOTOR POWER SUPPLY
With CONSULT
Connect 12V battery negative terminal.
Check the voltage between ABS actuator and electric unit (control unit) harness connector and ground.
+ — Voltage ABS actuator and electric unit (control unit) Connector Terminal B2 30 Ground 10 − 16 V
Is the inspection result normal?
YES>>GO TO 6.
NO>>GO TO 5.
CHECK MOTOR POWER SUPPLY CIRCUIT
Disconnect 12V battery negative terminal.
Check the 30A fusible link (#K). (Without ProPILOT Assist 2.0)
Check the 30A fusible link (#W). (With ProPILOT Assist 2.0)
Check the continuity and short circuit between ABS actuator and electric unit (control unit) harness connector terminal (30) and 30A fusible link (#K). (Without ProPILOT Assist 2.0)
Check the continuity and short circuit between ABS actuator and electric unit (control unit) harness connector terminal (30) and 30A fusible link (#W). (With ProPILOT Assist 2.0)
Is the inspection result normal?
YES>>Perform trouble diagnosis for 12V battery power supply.
NO>>Repair/replace harness, connector or fusible link.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) MODULE GROUND CIRCUIT
Disconnect 12V battery negative terminal.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and ground.
ABS actuator and electric unit (control unit) — Continuity Connector Terminal B2 46 Ground Existed
Is the inspection result normal?
YES>>GO TO 7.
NO>>Repair / replace harness or connector. GO TO 7.
CHECK TERMINAL
Check parking brake actuator (RH) terminals for damage or loose connection with harness connector
Check ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 8.
NO>>Repair / replace harness, connector, or terminal. GO TO 8.
PERFORM SELF-DIAGNOSIS
With CONSULT
Connect the parking brake actuator (RH) harness connector.
Connect the ABS actuator and electric unit (control unit) harness connector.
Connect 12V battery negative terminal.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Apply and release the parking brake five times.
Perform self-diagnosis for “ABS”.
Is DTC "C10B0-01" detected?
YES-1>>"CRNT" is displayed: Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
YES-2>>"PAST" is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO>>INSPECTION END
C10b0-09 Parking Brake Actuator (rh) Nissan Ariya: FE0
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C10B0 | 09 | Parking brake actuator (right) | Diagnosis condition | When parking brake is apply or release. | |
| Signal (terminal) | — | ||||
| Threshold | When a motor of the parking brake actuator (RH) is not rotate. | ||||
| Diagnosis delay time | 10 seconds or more | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Push the parking brake switch.
Pull the parking brake switch.
Perform self-diagnosis for “ABS”.
Is DTC “C10B0-09" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the parking brake actuator (RH) harness connector for disconnection or looseness.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair / replace harness or connector. GO TO 2.
CHECK PARKING BRAKE ACTUATOR CIRCUIT (1)
Disconnect the ABS actuator and electric unit (control unit) harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector terminals.
ABS actuator and electric unit (control unit) Continuity Connector Terminal B2 2 - 3 Existed
Is the inspection result normal?
YES>>GO TO 4.
NO>>GO TO 3.
CHECK PARKING BRAKE ACTUATOR CIRCUIT (2)
Check the continuity between parking brake actuator (RH) harness connector terminals.
| Terminal | Continuity |
|---|---|
| 1 - 2 | Existed |
Is the inspection result normal?
YES>>Repair / replace harness or connector.
NO>>Replace the parking brake actuator (RH). Refer to PARKING BRAKE ACTUATOR : Removal & Installation.
CHECK TERMINAL
Check parking brake actuator (RH) terminals for damage or loose connection with harness connector.
Check ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Repair / replace harness, connector, or terminal. GO TO 5.
CHECK PARKING BRAKE ACTUATOR
Connect the parking brake actuator (RH) harness connector.
Connect the ABS actuator and electric unit (control unit) harness connector.
Connect 12V battery negative terminal.
Power switch ON.
Pull or push parking brake switch, and check the operation sound of parking brake actuator.
Is the inspection result normal?
YES>>GO TO 6.
NO>>Replace the parking brake actuator (RH). Refer to PARKING BRAKE ACTUATOR : Removal & Installation.
PERFORM SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “ABS”.
Is DTC "C10B0-09" detected?
YES-1>>"CRNT" is displayed: Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
YES-2>>"PAST" is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO>>INSPECTION END
C10b1-01 Parking Brake Actuator (lh) Nissan Ariya
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C10B1 | 01 | Parking brake actuator (left) | Diagnosis condition | When parking brake is apply or release. | |
| Signal (terminal) | — | ||||
| Threshold | When an open circuit is detected in motor of parking brake actuator (LH). | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Push the parking brake switch.
Pull the parking brake switch.
Perform self-diagnosis for “ABS”.
Is DTC “C10B1-01" detected?
YES-1>>“CRNT” is displayed (only "C10B1-01"): Refer to DTC Diagnosis Procedure.
YES-2>>“CRNT” is displayed ("C10B0-01" and "C10B0-09): Refer to DTC Diagnosis Procedure.
YES-3>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the parking brake actuator (LH) harness connector for disconnection or looseness.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair / replace harness or connector. GO TO 2.
CHECK PARKING BRAKE ACTUATOR CIRCUIT (1)
Disconnect the ABS actuator and electric unit (control unit) harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector terminals.
ABS actuator and electric unit (control unit) Continuity Connector Terminal B2 13 - 12 Existed
Is the inspection result normal?
YES>>GO TO 4.
NO>>GO TO 3.
CHECK PARKING BRAKE ACTUATOR CIRCUIT (2)
Check the continuity between parking brake actuator (LH) harness connector terminals.
| Terminal | Continuity |
|---|---|
| 1 - 2 | Existed |
Is the inspection result normal?
YES>>Repair / replace harness or connector.
NO>>Replace the parking brake actuator (LH). Refer to PARKING BRAKE ACTUATOR : Removal & Installation.
CHECK MOTOR POWER SUPPLY
With CONSULT
Connect 12V battery negative terminal.
Check the voltage between ABS actuator and electric unit (control unit) harness connector and ground.
+ — Voltage ABS actuator and electric unit (control unit) Connector Terminal B2 30 Ground 10 − 16 V
Is the inspection result normal?
YES>>GO TO 6.
NO>>GO TO 5.
CHECK MOTOR POWER SUPPLY CIRCUIT
Disconnect 12V battery negative terminal.
Check the 30A fusible link (#K). (Without ProPILOT Assist 2.0)
Check the 30A fusible link (#W). (With ProPILOT Assist 2.0)
Check the continuity and short circuit between ABS actuator and electric unit (control unit) harness connector terminal (30) and 30A fusible link (#K). (Without ProPILOT Assist 2.0)
Check the continuity and short circuit between ABS actuator and electric unit (control unit) harness connector terminal (30) and 30A fusible link (#W). (With ProPILOT Assist 2.0)
Is the inspection result normal?
YES>>Perform trouble diagnosis for 12V battery power supply.
NO>>Repair/replace harness, connector or fusible link.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) MODULE GROUND CIRCUIT
Disconnect 12V battery negative terminal.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and ground.
ABS actuator and electric unit (control unit) — Continuity Connector Terminal B2 46 Ground Existed
Is the inspection result normal?
YES>>GO TO 7.
NO>>Repair / replace harness or connector. GO TO 7.
CHECK TERMINAL
Check parking brake actuator (LH) terminals for damage or loose connection with harness connector
Check ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 8.
NO>>Repair / replace harness, connector, or terminal. GO TO 8.
PERFORM SELF-DIAGNOSIS
With CONSULT
Connect the parking brake actuator (LH) harness connector.
Connect the ABS actuator and electric unit (control unit) harness connector.
Connect 12V battery negative terminal.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Apply and release the parking brake five times.
Perform self-diagnosis for “ABS”.
Is DTC "C10B1-01" detected?
YES-1>>"CRNT" is displayed: Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
YES-2>>"PAST" is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO>>INSPECTION END
C10b1-09 Parking Brake Actuator (lh) Nissan Ariya
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C10B1 | 09 | Parking brake actuator (left) | Diagnosis condition | When parking brake is apply or release. | |
| Signal (terminal) | — | ||||
| Threshold | When a motor of the parking brake actuator (LH) is not rotate. | ||||
| Diagnosis delay time | 10 seconds or more | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Push the parking brake switch.
Pull the parking brake switch.
Perform self-diagnosis for “ABS”.
Is DTC “C10B1-09" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the parking brake actuator (LH) harness connector for disconnection or looseness.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair / replace harness or connector. GO TO 2.
CHECK PARKING BRAKE ACTUATOR CIRCUIT (1)
Disconnect the ABS actuator and electric unit (control unit) harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector terminals.
ABS actuator and electric unit (control unit) Continuity Connector Terminal B2 13 - 12 Existed
Is the inspection result normal?
YES>>GO TO 4.
NO>>GO TO 3.
CHECK PARKING BRAKE ACTUATOR CIRCUIT (2)
Check the continuity between parking brake actuator (LH) harness connector terminals.
| Terminal | Continuity |
|---|---|
| 1 - 2 | Existed |
Is the inspection result normal?
YES>>Repair / replace harness or connector.
NO>>Replace the parking brake actuator (LH). Refer to PARKING BRAKE ACTUATOR : Removal & Installation.
CHECK TERMINAL
Check parking brake actuator (LH) terminals for damage or loose connection with harness connector.
Check ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Repair / replace harness, connector, or terminal. GO TO 5.
CHECK PARKING BRAKE ACTUATOR
Connect the parking brake actuator (LH) harness connector.
Connect the ABS actuator and electric unit (control unit) harness connector.
Connect 12V battery negative terminal.
Power switch ON.
Pull or push parking brake switch, and check the operation sound of parking brake actuator.
Is the inspection result normal?
YES>>GO TO 6.
NO>>Replace the parking brake actuator (LH). Refer to PARKING BRAKE ACTUATOR : Removal & Installation.
PERFORM SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “ABS”.
Is DTC "C10B0-09" detected?
YES-1>>"CRNT" is displayed: Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
YES-2>>"PAST" is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO>>INSPECTION END
C10b2-01 Parking Brake Switch Nissan Ariya SUV
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C10B2 | 01 | Parking brake switch | Diagnosis condition | Power switch is ON. | |
| Signal (terminal) | Parking brake switch signal | ||||
| Threshold | When a malfunction is detected in parking brake switch circuit. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Push the parking brake switch.
Pull the parking brake switch.
Perform self-diagnosis for “ABS”.
Is DTC “C10B2-01" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK DATA MONITOR
With CONSULT
Power switch ON.
Select “ABS”, “Data monitor” and “Parking brake switch” according to this order. Check that data monitor displays when parking brake switch is pull, neutral or push. Refer to Values On The Diagnosis Tool.
Is the inspection result normal?
YES>>GO TO 6.
NO>>GO TO 2.
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the parking brake switch harness connector for disconnection or looseness.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness or connector. GO TO 3.
CHECK PARKING BRAKE SWITCH CIRCUIT
Disconnect the parking brake switch harness connector.
Disconnect the ABS actuator and electric unit (control unit) harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and parking brake switch harness connector.
ABS actuator and electric unit (control unit) Parking brake switch Continuity Connector Terminal Connector Terminal B2 34 M144 9 Existed 15 3 32 5 16 6 31 7 Check the continuity between ABS actuator and electric unit (control unit) harness connector and ground.
ABS actuator and electric unit (control unit) — Continuity Connector Terminal B2 34 Ground Not existed 15 32 16 31
Is the inspection result normal?
YES>>GO TO 4.
NO>>Repair/replace harness or connector. GO TO 4.
CHECK PARKING BRAKE SWITCH
Check the parking brake switch. Refer to Component Inspection.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Replace the parking brake switch. Refer to PARKING BRAKE SWITCH : Removal & Installation.
CHECK TERMINAL
Check parking brake switch terminals for damage or loose connection with harness connector.
Check ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 6.
NO>>Repair / replace harness, connector, or terminal. GO TO 6.
PERFORM SELF-DIAGNOSIS
With CONSULT
Connect the parking brake switch harness connector.
Connect the ABS actuator and electric unit (control unit) harness connector.
Connect 12V battery negative terminal.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Apply and release the parking brake five times.
Perform self-diagnosis for “ABS”.
Is DTC "C10B2-01" detected?
YES-1>>"CRNT" is displayed: Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
YES-2>>"PAST" is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO>>INSPECTION END
C10b2-64 Parking Brake Switch Nissan Ariya: FE0
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C10B2 | 64 | Parking brake switch | Diagnosis condition | Power switch is ON. | |
| Signal (terminal) | Parking brake switch signal | ||||
| Threshold | When a malfunction is detected in parking brake switch circuit. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Push the parking brake switch.
Pull the parking brake switch.
Perform self-diagnosis for “ABS”.
Is DTC “C10B2-64" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK DATA MONITOR
With CONSULT
Power switch ON.
Select “ABS”, “Data monitor” and “Parking brake switch” according to this order. Check that data monitor displays when parking brake switch is pull, neutral or push. Refer to Values On The Diagnosis Tool.
Is the inspection result normal?
YES>>GO TO 6.
NO>>GO TO 2.
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the parking brake switch harness connector for disconnection or looseness.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness or connector. GO TO 3.
CHECK PARKING BRAKE SWITCH CIRCUIT
Disconnect the parking brake switch harness connector.
Disconnect the ABS actuator and electric unit (control unit) harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and parking brake switch harness connector.
ABS actuator and electric unit (control unit) Parking brake switch Continuity Connector Terminal Connector Terminal B2 34 M144 9 Existed 15 3 32 5 16 6 31 7 Check the continuity between ABS actuator and electric unit (control unit) harness connector and ground.
ABS actuator and electric unit (control unit) — Continuity Connector Terminal B2 34 Ground Not existed 15 32 16 31
Is the inspection result normal?
YES>>GO TO 4.
NO>>Repair/replace harness or connector. GO TO 4.
CHECK PARKING BRAKE SWITCH
Check the parking brake switch. Refer to Component Inspection.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Replace the parking brake switch. Refer to PARKING BRAKE SWITCH : Removal & Installation.
CHECK TERMINAL
Check parking brake switch terminals for damage or loose connection with harness connector.
Check ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 6.
NO>>Repair / replace harness, connector, or terminal. GO TO 6.
PERFORM SELF-DIAGNOSIS
With CONSULT
Connect the parking brake switch harness connector.
Connect the ABS actuator and electric unit (control unit) harness connector.
Connect 12V battery negative terminal.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Apply and release the parking brake five times.
Perform self-diagnosis for “ABS”.
Is DTC "C10B2-64" detected?
YES-1>>"CRNT" is displayed: Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
YES-2>>"PAST" is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO>>INSPECTION END
C10b3-44 Parking Brake Contrtol Module Nissan Ariya 2023
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C10B3 | 44 | Parking brake control module | Diagnosis condition | Power switch is ON. | |
| Signal (terminal) | — | ||||
| Threshold | When an internal malfunction in ABS actuator and electric unit (control unit). | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Push the parking brake switch.
Pull the parking brake switch.
Perform self-diagnosis for “ABS”.
Is DTC “C10B3-44" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
PERFORM SELF-DIAGNOSIS
With CONSULT
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Push the parking brake switch.
Pull the parking brake switch.
Perform self-diagnosis for “ABS”.
Is DTC "C10B3-44" detected?
YES-1>>"CRNT" is displayed: Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
YES-2>>"PAST" is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO>>INSPECTION END
C10b3-49 Parking Brake Contrtol Module Nissan Ariya 1st generation
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C10B3 | 49 | Parking brake control module | Diagnosis condition |
|
|
| Signal (terminal) | — | ||||
| Threshold | When an internal malfunction in ABS actuator and electric unit (control unit). | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Push the parking brake switch.
Pull the parking brake switch.
Perform self-diagnosis for “ABS”.
Is DTC “C10B3-49" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the parking brake actuator harness connector for disconnection or looseness.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair / replace harness or connector. GO TO 2.
CHECK PARKING BRAKE ACTUATOR CIRCUIT (1)
Disconnect the ABS actuator and electric unit (control unit) harness connector.
Check the continuity between ABS actuator and electric unit (control unit) harness connector terminals.
ABS actuator and electric unit (control unit) Continuity Connector Terminal B2 13 - 12 (Left) Existed 2 - 3 (Right)
Is the inspection result normal?
YES>>GO TO 4.
NO>>GO TO 3.
CHECK PARKING BRAKE ACTUATOR CIRCUIT (2)
Check the continuity between parking brake actuator harness connector terminals.
| Terminal | Continuity |
|---|---|
| 1 - 2 | Existed |
Is the inspection result normal?
YES>>Repair / replace harness or connector.
NO>>Replace the parking brake actuator. Refer to PARKING BRAKE ACTUATOR : Removal & Installation.
CHECK MOTOR POWER SUPPLY
Connect 12V battery negative terminal.
Check the voltage between ABS actuator and electric unit (control unit) harness connector and ground.
+ — Voltage ABS actuator and electric unit (control unit) Connector Terminal B2 30 Ground 10 − 16 V
Is the inspection result normal?
YES>>GO TO 6.
NO>>GO TO 5.
CHECK MOTOR POWER SUPPLY CIRCUIT
Disconnect 12V battery negative terminal.
Check the 30A fusible link (#K). (Without ProPILOT Assist 2.0)
Check the 30A fusible link (#W). (With ProPILOT Assist 2.0)
Check the continuity and short circuit between ABS actuator and electric unit (control unit) harness connector terminal (30) and 30A fusible link (#K). (Without ProPILOT Assist 2.0)
Check the continuity and short circuit between ABS actuator and electric unit (control unit) harness connector terminal (30) and 30A fusible link (#W). (With ProPILOT Assist 2.0)
Is the inspection result normal?
YES>>Perform trouble diagnosis for 12V battery power supply.
NO>>Repair/replace harness, connector or fusible link.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) MODULE GROUND CIRCUIT
Disconnect 12V battery negative terminal.
Check the continuity between ABS actuator and electric unit (control unit) harness connector and ground.
ABS actuator and electric unit (control unit) — Continuity Connector Terminal B2 46 Ground Existed
Is the inspection result normal?
YES>>GO TO 7.
NO>>Repair / replace harness or connector. GO TO 7.
CHECK TERMINAL
Check parking brake actuator terminals for damage or loose connection with harness connector.
Check ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>GO TO 8.
NO>>Repair / replace harness, connector, or terminal. GO TO 8.
PERFORM SELF-DIAGNOSIS
With CONSULT
Connect the parking brake actuator harness connector.
Connect the ABS actuator and electric unit (control unit) harness connector.
Connect 12V battery negative terminal.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Apply and release the parking brake five times.
Perform self-diagnosis for “ABS”.
Is DTC "C10B3-49" detected?
YES-1>>"CRNT" is displayed: Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
YES-2>>"PAST" is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO>>INSPECTION END
C10b3-53 Parking Brake Contrtol Module Nissan Ariya first Gen
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C10B3 | 53 | Parking brake control module | Diagnosis condition | Power switch is ON. | |
| Signal (terminal) | — | ||||
| Threshold | When an internal malfunction in ABS actuator and electric unit (control unit). | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Push the parking brake switch.
Pull the parking brake switch.
Perform self-diagnosis for “ABS”.
Is DTC “C10B3-53" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHANGE OF SYSTEM MODE
With CONSULT
Check the system mode after ABS actuator and electric unit (control unit) replacement.
Is system mode changes completed?
YES>>GO TO 2.
NO>>Perform change of system mode. Refer to Work Procedure. GO TO 2.
PERFORM SELF-DIAGNOSIS
With CONSULT
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC "C10B3-53" detected?
YES-1>>"CRNT" is displayed: Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
YES-2>>"PAST" is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO>>INSPECTION END
C10b3-55 Parking Brake Contrtol Module Nissan Ariya
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C10B3 | 55 | Parking brake control module | Diagnosis condition |
|
|
| Signal (terminal) | — | ||||
| Threshold | When an internal malfunction in ABS actuator and electric unit (control unit). | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Push the parking brake switch.
Pull the parking brake switch.
Perform self-diagnosis for “ABS”.
Is DTC “C10B3-55" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
PROGRAMING OF ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
Perform programing of ABS actuator and electric unit (control unit). Refer to Work Procedure.
>>GO TO 2.
PERFORM SELF-DIAGNOSIS
With CONSULT
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC "C10B3-55" detected?
YES-1>>"CRNT" is displayed: Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
YES-2>>"PAST" is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO>>INSPECTION END
C10b3-68 Parking Brake Control Module Nissan Ariya
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C10B3 | 68 | Parking brake control module | Diagnosis condition |
|
|
| Signal (terminal) | — | ||||
| Threshold | When an internal malfunction in ABS actuator and electric unit (control unit). | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Push the parking brake switch.
Pull the parking brake switch.
Perform self-diagnosis for “ABS”.
Is DTC “C10B3-68" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHANGE OF SYSTEM MODE
With CONSULT
Select “ABS”, “Work support” and “Finish brake pad replacement” in this order.
Select “START”.
GO TO 2.
PERFORM SELF-DIAGNOSIS
With CONSULT
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC "C10B3-68" detected?
YES-1>>"CRNT" is displayed: Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
YES-2>>"PAST" is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO>>INSPECTION END
C10b4-98 Parking Brake Over Heart Nissan Ariya
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C10B4 | 98 | Overheat | Diagnosis condition |
|
|
| Signal (terminal) | — | ||||
| Threshold | When a high temperature status is detected in electric parking brake system. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Push the parking brake switch.
Pull the parking brake switch.
Perform self-diagnosis for “ABS”.
Is DTC “C10B4-98" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
Erase self-diagnosis result for “ABS”.
After approximately 1 minute, operate (pull and push) parking brake switch.
Perform self-diagnosis for “ABS”.
Is DTC "C10B4-98" detected?
YES>>Check when parking brake actuator is stuck.
NO>>GO TO 2.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
Wait for 1 minute or more.
Operate and release the parking brake five times.
Perform self-diagnosis for “ABS”.
Is DTC "C10B4-98" detected?
YES-1>>"CRNT" is displayed: Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
YES-2>>"PAST" is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO>>INSPECTION END
C10b5-76 Parking Brake Assembly Check Nissan Ariya
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C10B5 | 76 | Parking brake assembly check | Diagnosis condition |
|
|
| Signal (terminal) | — | ||||
| Threshold | When an internal malfunction in ABS actuator and electric unit (control unit). (Maintenance mode) | ||||
| Diagnosis delay time | 30 seconds or more | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Push the parking brake switch.
Pull the parking brake switch.
Perform self-diagnosis for “ABS”.
Is DTC “C10B5-76" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
ADJUSTMENT OF BRAKE CALIPER INITIAL POSITION
Perform adjustment of brake caliper initial position. Refer to Work Procedure.
>>GO TO 2.
PERFORM SELF-DIAGNOSIS
With CONSULT
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC "C10B5-76" detected?
YES-1>>"CRNT" is displayed: Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
YES-2>>"PAST" is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO>>INSPECTION END
C10b6-68 Parking Brake System Nissan Ariya SUV
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C10B6 | 68 | Parking brake system | Diagnosis condition |
|
|
| Signal (terminal) | — | ||||
| Threshold | When a malfunction is detected in electric parking brake system. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
| Parking brake actuator |
|
FAIL-SAFE
The following functions are suspended.
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Push the parking brake switch.
Pull the parking brake switch.
Perform self-diagnosis for “ABS”.
Is DTC “C10B6-68" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK REAR BRAKE COMPONENT PARTS
Apply and release the parking brake.
Disconnect 12V battery negative terminal.
Check rear brake component parts.
Rear brake pad: Refer to REAR BRAKE PAD : Periodic Maintenance Operation.
Rear brake caliper assembly and parking brake actuator: Refer to REAR BRAKE CALIPER ASSEMBLY : Inspection.
Rear disc rotor: Refer to REAR DISC ROTOR : Periodic Maintenance Operation.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace error-detected parts. GO TO 2.
PERFORM SELF-DIAGNOSIS
With CONSULT
Connect 12V battery negative terminal.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Apply and release the parking brake five times.
Perform self-diagnosis for “ABS”.
Is DTC "C10B6-68" detected?
YES-1>>"CRNT" is displayed: Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
YES-2>>"PAST" is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO>>INSPECTION END
C10b7-16 Parking Brake Power Supply Nissan Ariya 1st generation
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C10B7 | 16 | Parking brake power supply | Diagnosis condition |
|
|
| Signal (terminal) | Power switch ON power supply | ||||
| Threshold | When power switch ON power supply voltage is 10 V or less. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Push the parking brake switch.
Pull the parking brake switch.
Perform self-diagnosis for “ABS”.
Is DTC “C10B7-16" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
PERFORM SELF-DIAGNOSIS
With CONSULT
Connect 12V battery negative terminal.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC "C10B7-16" detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C10b7-17 Parking Brake Power Supply Nissan Ariya 1st generation
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C10B7 | 17 | Parking brake power supply | Diagnosis condition |
|
|
| Signal (terminal) | Power switch ON power supply | ||||
| Threshold | When power switch ON power supply voltage is 18 V or more. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Push the parking brake switch.
Pull the parking brake switch.
Perform self-diagnosis for “ABS”.
Is DTC “C10B7-17" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK CONNECTOR
Disconnect 12V battery negative terminal.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair / replace harness or connector, securely lock the connector. GO TO 2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
PERFORM SELF-DIAGNOSIS
With CONSULT
Connect 12V battery negative terminal.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC "C10B7-17" detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
NO>>INSPECTION END
C10b8-77 Parking Brake System Nissan Ariya SUV
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C10B8 | 77 | Parking brake system | Diagnosis condition |
|
|
| Signal (terminal) | — | ||||
| Threshold | When a motor of parking brake actuator does not reach the target position. | ||||
| Diagnosis delay time | 30 seconds or more | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Push the parking brake switch.
Pull the parking brake switch.
Perform self-diagnosis for “ABS”.
Is DTC “C10B8-77" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK REAR BRAKE COMPONENT PARTS
Apply and release the parking brake.
Disconnect 12V battery negative terminal.
Check rear brake component parts.
Rear brake pad: Refer to REAR BRAKE PAD : Periodic Maintenance Operation.
Rear brake caliper assembly and parking brake actuator: Refer to REAR BRAKE CALIPER ASSEMBLY : Inspection.
Rear disc rotor: Refer to REAR DISC ROTOR : Periodic Maintenance Operation.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace error-detected parts. GO TO 2.
PERFORM SELF-DIAGNOSIS
With CONSULT
Connect 12V battery negative terminal.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Apply and release the parking brake five times.
Perform self-diagnosis for “ABS”.
Is DTC "C10B8-77" detected?
YES-1>>"CRNT" is displayed: Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
YES-2>>"PAST" is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO>>INSPECTION END
C10b9-77 Parking Brake System Nissan Ariya 2026
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | |||
|---|---|---|---|---|---|
| C10B9 | 77 | Parking brake system | Diagnosis condition |
|
|
| Signal (terminal) | — | ||||
| Threshold | When a malfunction is detected in electric parking brake system. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Push the parking brake switch.
Pull the parking brake switch.
Perform self-diagnosis for “ABS”.
Is DTC “C10B9-77" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK REAR BRAKE COMPONENT PARTS
Apply and release the parking brake.
Disconnect 12V battery negative terminal.
Check rear brake component parts.
Rear brake pad: Refer to REAR BRAKE PAD : Periodic Maintenance Operation.
Rear brake caliper assembly and parking brake actuator: Refer to REAR BRAKE CALIPER ASSEMBLY : Inspection.
Rear disc rotor: Refer to REAR DISC ROTOR : Periodic Maintenance Operation.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace error-detected parts. GO TO 2.
PERFORM SELF-DIAGNOSIS
With CONSULT
Connect 12V battery negative terminal.
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Apply and release the parking brake five times.
Perform self-diagnosis for “ABS”.
Is DTC "C10B9-77" detected?
YES-1>>"CRNT" is displayed: Replace the ABS actuator and electric unit (control unit). Refer to ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) : Removal & Installation.
YES-2>>"PAST" is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO>>INSPECTION END
U0073-00 Can Comm Circuit Nissan Ariya: FE0
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | ||||
|---|---|---|---|---|---|---|
| U0073 | 00 | Control module comm Bus A Off | 1 | Diagnosis condition |
|
|
| Signal (terminal) | CAN communication signal | |||||
| Threshold | When CAN communication signal is not continuously transmitted from ABS actuator and electric unit (control unit). | |||||
| Diagnosis delay time | 2 seconds or more | |||||
| 2 | Diagnosis condition |
|
||||
| Signal (terminal) | CAN communication signal | |||||
| Threshold | When CAN communication signal is not continuously received from ABS actuator and electric unit (control unit). | |||||
| Diagnosis delay time | 2 seconds or more | |||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
| Harness or connector |
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “U0073-00" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
Refer to Trouble Diagnosis Flow Chart.
U0073-88 Can Communication Nissan Ariya SUV
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | ||||
|---|---|---|---|---|---|---|
| U0073 | 88 | Control module comm Bus A Off | 1 | Diagnosis condition |
|
|
| Signal (terminal) | CAN communication signal | |||||
| Threshold | When CAN communication signal is not continuously transmitted from ABS actuator and electric unit (control unit). | |||||
| Diagnosis delay time | 2 seconds or more | |||||
| 2 | Diagnosis condition |
|
||||
| Signal (terminal) | CAN communication signal | |||||
| Threshold | When CAN communication signal is not continuously received from ABS actuator and electric unit (control unit). | |||||
| Diagnosis delay time | 2 seconds or more | |||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
| Harness or connector |
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “U0073-88" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
Refer to Trouble Diagnosis Flow Chart.
U0076-00 Can Comm Circuit Nissan Ariya 2026
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | ||||
|---|---|---|---|---|---|---|
| U0076 | 00 | Control module comm Bus D Off | 1 | Diagnosis condition |
|
|
| Signal (terminal) | CAN communication signal | |||||
| Threshold | When CAN communication signal is not continuously transmitted from ABS actuator and electric unit (control unit). | |||||
| Diagnosis delay time | 2 seconds or more | |||||
| 2 | Diagnosis condition |
|
||||
| Signal (terminal) | CAN communication signal | |||||
| Threshold | When CAN communication signal is not continuously received from ABS actuator and electric unit (control unit). | |||||
| Diagnosis delay time | 2 seconds or more | |||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
| Harness or connector |
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “U0076-00" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
Refer to Trouble Diagnosis Flow Chart.
U0076-88 Can Comm Circuit Nissan Ariya SUV
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | ||||
|---|---|---|---|---|---|---|
| U0076 | 88 | Control module comm Bus D Off | 1 | Diagnosis condition |
|
|
| Signal (terminal) | CAN communication signal | |||||
| Threshold | When CAN communication signal is not continuously transmitted from ABS actuator and electric unit (control unit). | |||||
| Diagnosis delay time | 2 seconds or more | |||||
| 2 | Diagnosis condition |
|
||||
| Signal (terminal) | CAN communication signal | |||||
| Threshold | When CAN communication signal is not continuously received from ABS actuator and electric unit (control unit). | |||||
| Diagnosis delay time | 2 seconds or more | |||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
| Harness or connector |
|
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “U0076-88" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
Refer to Trouble Diagnosis Flow Chart.
U2112-87 Can Comm Circuit Nissan Ariya
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | ||||
|---|---|---|---|---|---|---|
| U2112 | 87 | CAN communication error brake unit | 1 | Diagnosis condition |
|
|
| Signal (terminal) | CAN communication signal | |||||
| Threshold | When CAN communication signal is not continuously transmitted to electrically-driven intelligent brake unit. | |||||
| Diagnosis delay time | 2 seconds or more | |||||
| 2 | Diagnosis condition |
|
||||
| Signal (terminal) | CAN communication signal | |||||
| Threshold | When CAN communication signal is not continuously received from electrically-driven intelligent brake unit. | |||||
| Diagnosis delay time | 2 seconds or more | |||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
Harness or connector |
FAIL-SAFE
Normal control
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “U2112-87" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
Refer to Trouble Diagnosis Flow Chart.
U2140-87 Can Comm Circuit Nissan Ariya 2026
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | ||||
|---|---|---|---|---|---|---|
| U2140 | 87 | Controller area network communication error (Engine control module) | 1 | Diagnosis condition |
|
|
| Signal (terminal) | CAN communication signal | |||||
| Threshold | When CAN communication signal is not continuously transmitted to VCM. | |||||
| Diagnosis delay time | 2 seconds or more | |||||
| 2 | Diagnosis condition |
|
||||
| Signal (terminal) | CAN communication signal | |||||
| Threshold | When CAN communication signal is not continuously received from VCM. | |||||
| Diagnosis delay time | 2 seconds or more | |||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
Harness or connector |
FAIL-SAFE
Normal control
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “U2140-87" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
Refer to Trouble Diagnosis Flow Chart.
U2143-87 Can Comm Err Nissan Ariya 2026
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | ||||
|---|---|---|---|---|---|---|
| U2143 | 87 | Controller area network communication error (Nissan Ariya Vehicle control module/Hybrid control module) | 1 | Diagnosis condition |
|
|
| Signal (terminal) | CAN communication signal | |||||
| Threshold | When CAN communication signal is not continuously transmitted to VCM. | |||||
| Diagnosis delay time | 2 seconds or more | |||||
| 2 | Diagnosis condition |
|
||||
| Signal (terminal) | CAN communication signal | |||||
| Threshold | When CAN communication signal is not continuously received from VCM. | |||||
| Diagnosis delay time | 2 seconds or more | |||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
Harness or connector |
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “U2143-87" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
Refer to Trouble Diagnosis Flow Chart.
U214e-87 Can Comm Err Nissan Ariya
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | ||||
|---|---|---|---|---|---|---|
| U214E | 87 | CAN communication error combination meter | 1 | Diagnosis condition |
|
|
| Signal (terminal) | CAN communication signal | |||||
| Threshold | When CAN communication signal is not continuously transmitted to combination meter. | |||||
| Diagnosis delay time | 2 seconds or more | |||||
| 2 | Diagnosis condition |
|
||||
| Signal (terminal) | CAN communication signal | |||||
| Threshold | When CAN communication signal is not continuously received from combination meter. | |||||
| Diagnosis delay time | 2 seconds or more | |||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
Harness or connector |
FAIL-SAFE
Normal control
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “U214E-87" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
Refer to Trouble Diagnosis Flow Chart.
U214f-87 Can Comm Err Nissan Ariya SUV
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | ||||
|---|---|---|---|---|---|---|
| U214F | 87 | CAN communication error (BCM) | 1 | Diagnosis condition |
|
|
| Signal (terminal) | CAN communication signal | |||||
| Threshold | When CAN communication signal is not continuously transmitted to BCM. | |||||
| Diagnosis delay time | 2 seconds or more | |||||
| 2 | Diagnosis condition |
|
||||
| Signal (terminal) | CAN communication signal | |||||
| Threshold | When CAN communication signal is not continuously received from BCM. | |||||
| Diagnosis delay time | 2 seconds or more | |||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
Harness or connector |
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “U214F-87" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
Refer to Trouble Diagnosis Flow Chart.
U2152-87 Can Comm Circuit Nissan Ariya first Gen
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | ||||
|---|---|---|---|---|---|---|
| U2152 | 87 | CAN communication error advanced driver assistant systems control unit | 1 | Diagnosis condition |
|
|
| Signal (terminal) | CAN communication signal | |||||
| Threshold | When CAN communication signal is not continuously transmitted to ADAS control unit 2. | |||||
| Diagnosis delay time | 2 seconds or more | |||||
| 2 | Diagnosis condition |
|
||||
| Signal (terminal) | CAN communication signal | |||||
| Threshold | When CAN communication signal is not continuously received from ADAS control unit 2. | |||||
| Diagnosis delay time | 2 seconds or more | |||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
Harness or connector |
FAIL-SAFE
Normal control
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “U2152-87" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
Refer to Trouble Diagnosis Flow Chart.
U2154-87 Can Comm Circuit Nissan Ariya 2026
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | ||||
|---|---|---|---|---|---|---|
| U2154 | 87 | CAN communication error multimedia interface unit | 1 | Diagnosis condition |
|
|
| Signal (terminal) | CAN communication signal | |||||
| Threshold | When CAN communication signal is not continuously transmitted to AV control unit. | |||||
| Diagnosis delay time | 2 seconds or more | |||||
| 2 | Diagnosis condition |
|
||||
| Signal (terminal) | CAN communication signal | |||||
| Threshold | When CAN communication signal is not continuously received from AV control unit. | |||||
| Diagnosis delay time | 2 seconds or more | |||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
Harness or connector |
FAIL-SAFE
Normal control
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “U2154-87" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
Refer to Trouble Diagnosis Flow Chart.
U2156-87 Can Comm Circuit Nissan Ariya 1st generation
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | ||||
|---|---|---|---|---|---|---|
| U2156 | 87 | CAN communication error steering angel sensor | 1 | Diagnosis condition |
|
|
| Signal (terminal) | CAN communication signal | |||||
| Threshold | When CAN communication signal is not continuously transmitted to steering angle sensor. | |||||
| Diagnosis delay time | 2 seconds or more | |||||
| 2 | Diagnosis condition |
|
||||
| Signal (terminal) | CAN communication signal | |||||
| Threshold | When CAN communication signal is not continuously received from steering angle sensor | |||||
| Diagnosis delay time | 2 seconds or more | |||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
Harness or connector |
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “U2156-87" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
Refer to Trouble Diagnosis Flow Chart.
U215b-87 Can Comm Circuit Nissan Ariya: FE0
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | ||||
|---|---|---|---|---|---|---|
| U215B | 87 | CAN communication error (IPDM E/R) | 1 | Diagnosis condition |
|
|
| Signal (terminal) | CAN communication signal | |||||
| Threshold | When CAN communication signal is not continuously transmitted to IPDM E/R. | |||||
| Diagnosis delay time | 2 seconds or more | |||||
| 2 | Diagnosis condition |
|
||||
| Signal (terminal) | CAN communication signal | |||||
| Threshold | When CAN communication signal is not continuously received from IPDM E/R. | |||||
| Diagnosis delay time | 2 seconds or more | |||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
Harness or connector |
FAIL-SAFE
Normal control
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “U215B-87" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
Refer to Trouble Diagnosis Flow Chart.
U2212-87 Can Comm Circuit Nissan Ariya first Gen
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | ||||
|---|---|---|---|---|---|---|
| U2212 | 87 | CAN communication error brake unit | 1 | Diagnosis condition |
|
|
| Signal (terminal) | CAN communication signal | |||||
| Threshold | When CAN communication signal is not continuously transmitted to electrically-driven intelligent brake unit. | |||||
| Diagnosis delay time | 2 seconds or more | |||||
| 2 | Diagnosis condition |
|
||||
| Signal (terminal) | CAN communication signal | |||||
| Threshold | When CAN communication signal is not continuously received from electrically-driven intelligent brake unit. | |||||
| Diagnosis delay time | 2 seconds or more | |||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
Harness or connector |
FAIL-SAFE
The following functions are suspended.
hill start assist function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “U2212-87" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
Refer to Trouble Diagnosis Flow Chart.
U2240-87 Can Comm Circuit Nissan Ariya 2023
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | ||||
|---|---|---|---|---|---|---|
| U2240 | 87 | Controller area network communication error (Engine control module) | 1 | Diagnosis condition |
|
|
| Signal (terminal) | CAN communication signal | |||||
| Threshold | When CAN communication signal is not continuously transmitted to VCM. | |||||
| Diagnosis delay time | 2 seconds or more | |||||
| 2 | Diagnosis condition |
|
||||
| Signal (terminal) | CAN communication signal | |||||
| Threshold | When CAN communication signal is not continuously received from VCM. | |||||
| Diagnosis delay time | 2 seconds or more | |||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
Harness or connector |
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “U2240-87" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
Refer to Trouble Diagnosis Flow Chart.
U2241-87 Can Comm Circuit Nissan Ariya
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | ||||
|---|---|---|---|---|---|---|
| U2241 | 87 | Controller area network communication error (transmission control module) | 1 | Diagnosis condition |
|
|
| Signal (terminal) | CAN communication signal | |||||
| Threshold | When CAN communication signal is not continuously transmitted to VCM. | |||||
| Diagnosis delay time | 2 seconds or more | |||||
| 2 | Diagnosis condition |
|
||||
| Signal (terminal) | CAN communication signal | |||||
| Threshold | When CAN communication signal is not continuously received from VCM. | |||||
| Diagnosis delay time | 2 seconds or more | |||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
Harness or connector |
FAIL-SAFE
The following functions are suspended.
hill start assist function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “U2241-87" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
Refer to Trouble Diagnosis Flow Chart.
U2243-87 Can Comm Err Nissan Ariya 2023
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | ||||
|---|---|---|---|---|---|---|
| U2243 | 87 | Controller area network communication error (Nissan Ariya Vehicle control module/Hybrid control module) | 1 | Diagnosis condition |
|
|
| Signal (terminal) | CAN communication signal | |||||
| Threshold | When CAN communication signal is not continuously transmitted to VCM. | |||||
| Diagnosis delay time | 2 seconds or more | |||||
| 2 | Diagnosis condition |
|
||||
| Signal (terminal) | CAN communication signal | |||||
| Threshold | When CAN communication signal is not continuously received from VCM. | |||||
| Diagnosis delay time | 2 seconds or more | |||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
Harness or connector |
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “U2243-87" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
Refer to Trouble Diagnosis Flow Chart.
U224e-87 Can Comm Circuit Nissan Ariya SUV
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | ||||
|---|---|---|---|---|---|---|
| U224E | 87 | CAN communication error combination meter | 1 | Diagnosis condition |
|
|
| Signal (terminal) | CAN communication signal | |||||
| Threshold | When CAN communication signal is not continuously transmitted to combination meter. | |||||
| Diagnosis delay time | 2 seconds or more | |||||
| 2 | Diagnosis condition |
|
||||
| Signal (terminal) | CAN communication signal | |||||
| Threshold | When CAN communication signal is not continuously received from combination meter. | |||||
| Diagnosis delay time | 2 seconds or more | |||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
Harness or connector |
FAIL-SAFE
The following functions are suspended.
VDC function
TCS function
hill start assist function
Brake limited slip differential (BLSD) function
Brake assist function
Brake force distribution function
Cooperative regenerative brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “U224E-87" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
Refer to Trouble Diagnosis Flow Chart.
U2252-87 Can Comm Circuit Nissan Ariya
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | ||||
|---|---|---|---|---|---|---|
| U2252 | 87 | CAN communication error advanced driver assistant systems control unit | 1 | Diagnosis condition |
|
|
| Signal (terminal) | CAN communication signal | |||||
| Threshold | When CAN communication signal is not continuously transmitted to ADAS control unit 2. | |||||
| Diagnosis delay time | 2 seconds or more | |||||
| 2 | Diagnosis condition |
|
||||
| Signal (terminal) | CAN communication signal | |||||
| Threshold | When CAN communication signal is not continuously received from ADAS control unit 2. | |||||
| Diagnosis delay time | 2 seconds or more | |||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
Harness or connector |
FAIL-SAFE
Normal control
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “U2252-87" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
Refer to Trouble Diagnosis Flow Chart.
U225b-87 Can Comm Circuit Nissan Ariya SUV
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | ||||
|---|---|---|---|---|---|---|
| U225B | 87 | CAN communication error (IPDM E/R) | 1 | Diagnosis condition |
|
|
| Signal (terminal) | CAN communication signal | |||||
| Threshold | When CAN communication signal is not continuously transmitted to IPDM E/R. | |||||
| Diagnosis delay time | 2 seconds or more | |||||
| 2 | Diagnosis condition |
|
||||
| Signal (terminal) | CAN communication signal | |||||
| Threshold | When CAN communication signal is not continuously received from IPDM E/R. | |||||
| Diagnosis delay time | 2 seconds or more | |||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
Harness or connector |
FAIL-SAFE
The following functions are suspended.
hill start assist function
Electric parking brake function
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “U225B-87" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
Refer to Trouble Diagnosis Flow Chart.
U2275-87 Can Comm Circuit Nissan Ariya 2026
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | ||||
|---|---|---|---|---|---|---|
| U2275 | 87 | CAN communication error around view monitor control unit | 1 | Diagnosis condition |
|
|
| Signal (terminal) | CAN communication signal | |||||
| Threshold | When CAN communication signal is not continuously transmitted to ADAS control unit 2. | |||||
| Diagnosis delay time | 2 seconds or more | |||||
| 2 | Diagnosis condition |
|
||||
| Signal (terminal) | CAN communication signal | |||||
| Threshold | When CAN communication signal is not continuously received from ADAS control unit 2. | |||||
| Diagnosis delay time | 2 seconds or more | |||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
Harness or connector |
FAIL-SAFE
Normal control
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “U2275-87" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
Refer to Trouble Diagnosis Flow Chart.
U2276-87 Can Comm Circuit Nissan Ariya: FE0
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms | DTC detection condition | ||||
|---|---|---|---|---|---|---|
| U2276 | 87 | CAN communication error (chassis control module/steering angle sensor) | 1 | Diagnosis condition |
|
|
| Signal (terminal) | CAN communication signal | |||||
| Threshold | When CAN communication signal is not continuously transmitted to chassis control module. | |||||
| Diagnosis delay time | 2 seconds or more | |||||
| 2 | Diagnosis condition |
|
||||
| Signal (terminal) | CAN communication signal | |||||
| Threshold | When CAN communication signal is not continuously received from chassis control module. | |||||
| Diagnosis delay time | 2 seconds or more | |||||
POSSIBLE CAUSE
| PAST DTC | CRNT DTC |
|---|---|
|
Harness or connector |
FAIL-SAFE
Normal control
Confirmation Procedure
PRECONDITIONING
If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors before conducting the next test.
>>GO TO 2
CHECK DTC DETECTION
With CONSULT
Power switch OFF (Auto ACC is ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is DTC “U2276-87" detected?
YES-1>>“CRNT” is displayed: Refer to DTC Diagnosis Procedure.
YES-2>>“PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
Refer to Trouble Diagnosis Flow Chart.
Power Supply and Ground Circuit [abs Actuator and Electric Unit (control Unit)] Nissan Ariya 2023
Diagnosis Procedure
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SWITCH ON POWER SUPPLY
Power switch OFF.
Disconnect the ABS actuator and electric unit (control unit) harness connector.
Check the voltage between ABS actuator and electric unit (control unit) harness connector and ground.
+ — Voltage ABS actuator and electric unit (control unit) Connector Terminal B2 36 Ground Approx. 0 V Power switch ON.
Check the voltage between ABS actuator and electric unit (control unit) harness connector and ground.
+ — Voltage ABS actuator and electric unit (control unit) Connector Terminal B2 36 Ground 10 − 16 V
Is the inspection result normal?
YES>>GO TO 3.
NO>>GO TO 2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SWITCH ON POWER SUPPLY
Power switch OFF.
Check the 5A fuse (#39). (Without ProPILOT Assist 2.0)
Check the 10A fuse (#111). (With ProPILOT Assist 2.0)
Check the continuity between ABS actuator and electric unit (control unit) harness connector and fuse block (J/B) harness connector. (Without ProPILOT Assist 2.0)
ABS actuator and electric unit (control unit) Fuse block (J/B) Continuity Connector Terminal Connector Terminal B2 36 E57 71 Existed Check the continuity and short circuit between ABS actuator and electric unit (control unit) harness connector terminal (36) and 10A fuse (#111). (With ProPILOT Assist 2.0)
Is the inspection result normal?
YES>>Perform trouble diagnosis for power switch ON power supply.
NO>>Repair / replace harness, connector, or fuse.
CHECK ABS MOTOR, AND MOTOR RELAY POWER SUPPLY
Power switch OFF.
Check the voltage between ABS actuator and electric unit (control unit) harness connector and ground.
+ — Voltage ABS actuator and electric unit (control unit) Connector Terminal B2 1 Ground 10 – 16 V
Is the inspection result normal?
YES>>GO TO 5.
NO >>GO TO 4.
CHECK ABS MOTOR AND MOTOR RELAY POWER SUPPLY CIRCUIT
Power switch OFF.
Check the 60A fusible link (#C). (Without ProPILOT Assist 2.0)
Check the 80A fusible link (#AE). (With ProPILOT Assist 2.0)
Check the continuity and short circuit between ABS actuator and electric unit (control unit) harness connector terminal (1) and 600A fusible link (#C). (Without ProPILOT Assist 2.0)
Check the continuity and short circuit between ABS actuator and electric unit (control unit) harness connector terminal (1) and 80A fusible link (#AE). (With ProPILOT Assist 2.0)
Is the inspection result normal?
YES>>Perform trouble diagnosis for 12V battery power supply.
NO>>Repair / replace harness, connector, or fusible link.
CHECK ACTUATOR RELAY, EACH VALVE, PARKING BRAKE ACTUATOR POWER SUPPLY
Power switch OFF.
Check the voltage between ABS actuator and electric unit (control unit) harness connector and ground.
+ — Voltage ABS actuator and electric unit (control unit) Connector Terminal B1 30 Ground 10 – 16 V
Is the inspection result normal?
YES>>GO TO 7.
NO>>GO TO 6.
CHECK ACTUATOR RELAY, EACH VALVE, PARKING BRAKE ACTUATOR POWER SUPPLY CIRCUIT
Power switch OFF.
Check the 30A fusible link (#K). (Without ProPILOT Assist 2.0)
Check the 30A fusible link (#W). (With ProPILOT Assist 2.0)
Check the continuity and short circuit between ABS actuator and electric unit (control unit) harness connector terminal (30) and 30A fusible link (#K). (Without ProPILOT Assist 2.0)
Check the continuity and short circuit between ABS actuator and electric unit (control unit) harness connector terminal (30) and 30A fusible link (#W). (With ProPILOT Assist 2.0)
Is the inspection result normal?
YES>>Perform trouble diagnosis for 12V battery power supply.
NO>>Repair / replace harness, connector, or fuse.
CHECK GROUND CIRCUIT
Check the continuity between ABS actuator and electric unit (control unit) harness connector and the ground.
| ABS actuator and electric unit (control unit) | — | Continuity | |
|---|---|---|---|
| Connector | Terminal | ||
| B2 | 14 | Ground | Existed |
| 46 | |||
Is the inspection result normal?
YES>>GO TO 8.
NO>>Repair / replace harness or connector.
CHECK TERMINAL
Check ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES>>INSPECTION END
NO>>Repair / replace harness, connector, or terminal.
Brake Fluid Level Switch Nissan Ariya 1st generation
Component Inspection
CHECK BRAKE FLUID LEVEL SWITCH
Power switch OFF.
Disconnect brake fluid level switch harness connector.
Check the continuity between terminals of brake fluid level switch.
Brake fluid level switch Condition Continuity Terminal 1 – 2 When brake fluid level in reservoir tank is within the specified level. Not existed When brake fluid level in reservoir tank is less than the specified level. Existed
Is the inspection result normal?
YES>>INSPECTION END
NO>>Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.
Abs Warning Lamp Nissan Ariya: FE0
Component Function Check
CHECK ABS WARNING LAMP FUNCTION
Check that ABS warning lamp in combination meter turns ON for several seconds after power switch is ON.
Is the inspection result normal?
YES>>INSPECTION END
NO>>Refer to Diagnosis Procedure.
Diagnosis Procedure
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Perform the trouble diagnosis for ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
PERFORM SELF-DIAGNOSIS
With CONSULT
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is any DTC detected?
YES>>Check the DTC. Refer to DTC Index.
NO>>Check the combination meter. Refer to On Board Diagnosis Function.
Brake Warning Lamp Nissan Ariya first Gen
Component Function Check
CHECK BRAKE WARNING LAMP FUNCTION (1)
Check that brake warning lamp in combination meter turns ON for several seconds after power switch is ON.
Is the inspection result normal?
YES >>GO TO 2.
NO>>Refer to Diagnosis Procedure.
CHECK BRAKE WARNING LAMP FUNCTION (2)
Check that brake warning lamp in combination meter turns ON/OFF when brake fluid level switch is operated while brake fluid level in reservoir tank is with the specified level.
Is the inspection result normal?
YES>>INSPECTION END
NO>>Check brake fluid level switch system. Refer to DTC Description.
Diagnosis Procedure
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Perform the trouble diagnosis for ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
PERFORM SELF-DIAGNOSIS
With CONSULT
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is any DTC detected?
YES>>Check the DTC. Refer to On Board Diagnosis Function.
NO>>Check the combination meter. Refer to On Board Diagnosis Function.
Vdc Off Indicator Lamp Nissan Ariya 2023
Component Function Check
CHECK VDC OFF INDICATOR LAMP FUNCTION
Check that VDC OFF indicator lamp in combination meter turns ON for several seconds after power switch is ON.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Proceed to diagnosis procedure. Refer to Diagnosis Procedure.
CHECK VDC OFF INDICATOR LAMP OPERATION (VDC SETTING)
Check that VDC OFF indicator lamp is turned ON/OFF when VDC setting is changed ON/OFF with the information display of combination meter.
Is the inspection result normal?
YES>>INSPECTION END
NO>>Refer to Diagnosis Procedure.
Diagnosis Procedure
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Perform the trouble diagnosis for ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>Check combination meter. Refer to On Board Diagnosis Function.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
Vdc Warning Lamp Nissan Ariya 2023
Component Function Check
CHECK VDC WARNING LAMP FUNCTION
Check that VDC warning lamp in combination meter turns ON for several seconds after power switch is ON.
Is the inspection result normal?
YES>>INSPECTION END
NO>>Refer to Diagnosis Procedure.
Diagnosis Procedure
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Perform the trouble diagnosis for ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
PERFORM SELF-DIAGNOSIS
With CONSULT
Power switch OFF (Auto ACC function ON).
Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.
Power switch ON without depressing the brake pedal.
Perform self-diagnosis for “ABS”.
Is any DTC detected?
YES>>Check the DTC. Refer to DTC Index.
NO>>Check the combination meter. Refer to On Board Diagnosis Function.