Dtc/circuit Diagnosis
- B2f60-55 Seat Belt Buckle Sw (dr)
- Seat Belt Buckle Switch (driver Side)
- Rear Seat Belt Buckle Switch
B2f60-55 Seat Belt Buckle Sw (dr) Nissan Ariya: FE0
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen items | DTC detecting condition | |
|---|---|---|---|
| B2F60-55 | Seat belt buckle switch (driver side) | Diagnosis condition | Power switch ON |
| Signal (terminal) | — | ||
| Threshold | Configuration of the BCM is not completed | ||
| Diagnosis delay time | 1 second or less | ||
POSSIBLE CAUSE
BCM
BCM is not configured
FAIL-SAFE
—
DTC CONFIRMATION PROCEDURE
CHECK SELF-DIAG RESULT
With CONSULT
Power switch ON.
Check “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?
YES>>Refer to DTC Diagnosis Procedure.
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
PERFORM CONFIGURATION (BCM)
Perform BCM configuration. Refer to Work Procedure.
Perform DTC CONFIRMATION PROCEDURE for B2F60–55. Refer to DTC Description.
Is the DTC detected?
YES>>GO TO 2.
NO>>INSPECTION END
REPLACE BCM
Replace BCM. Refer to Removal and Installation.
>>INSPECTION END
Seat Belt Buckle Switch (driver Side) Nissan Ariya
Component Function Check
CHECK FUNCTION
Power switch ON.
Select “BCM” using CONSULT.
Select “Seat belt switch (driver)” in “DATA MONITOR” mode.
Check that the function operates normally according to the following conditions.
| Monitor item | Condition | Status | |
|---|---|---|---|
| Seat belt switch (driver) | Seat belt (driver side) | Unfastened | OFF |
| Fastened | ON | ||
Is the inspection result normal?
YES >>Seat belt buckle switch (driver side) is OK.
NO>>Refer to Diagnosis Procedure.
Diagnosis Procedure
CHECK SEAT BELT BUCKLE SWITCH INPUT SIGNAL
Power switch OFF.
Disconnect seat belt buckle switch (driver side) connector.
Power switch ON.
Check voltage between seat belt buckle switch (driver side) harness connector and ground.
(+) (–) Voltage Seat belt buckle switch (driver side) Connector Terminal B459 4 Ground 9 – 16 V
Is the inspection result normal?
YES>>GO TO 3.
NO>>GO TO 2.
CHECK SEAT BELT BUCKLE SWITCH CIRCUIT
Power switch OFF.
Disconnect BCM connector.
Check continuity between seat belt buckle switch (driver side) harness connector and BCM harness connector.
Seat belt buckle switch (driver side) BCM Continuity Connector Terminal Connector Terminal B459 4 M8 17 Existed Check continuity between BCM harness connector and ground.
BCM - Continuity Connector Terminal M8 17 Ground Not existed
Is the inspection result normal?
YES>>Replace BCM. Refer to Removal and Installation.
NO>>Repair or replace harness.
CHECK SEAT BELT BUCKLE SWITCH GROUND CIRCUIT
Power switch OFF.
Check continuity between seat belt buckle switch (driver side) harness connector and ground.
Seat belt buckle switch (driver side) - Continuity Connector Terminal B459 3 Ground Existed
Is the inspection result normal?
YES>>GO TO 4.
NO>>Repair or replace harness.
CHECK SEAT BELT BUCKLE SWITCH (DRIVER SIDE)
Check seat belt buckle switch (driver side). Refer to Component Inspection.
Is the inspection result normal?
YES>>INSPECTION END
NO>>Replace seat belt buckle (driver side). Refer to Removal & Installation.
Component Inspection
CHECK SEAT BELT BUCKLE SWITCH (DRIVER SIDE)
Power switch OFF.
Disconnect seat belt buckle switch (driver side) connector.
Check continuity of seat belt buckle switch (driver side) terminals.
Seat belt buckle switch (driver side) Condition Continuity Terminal 3 4 Seat belt (driver side) Fastened Not existed Unfastened Existed
Is the inspection result normal?
YES>>INSPECTION END
NO>>Replace seat belt buckle (driver side). Refer to Removal & Installation.
Rear Seat Belt Buckle Switch Nissan Ariya
Diagnosis Procedure
CHECK REAR SEAT BELT BUCKLE SWITCH GROUND CIRCUIT
Power switch OFF.
Disconnect rear seat belt buckle switch connector.
Check the continuity between rear seat belt buckle switch harness connector and ground.
| Rear seat belt buckle switch | — | Continuity | ||
|---|---|---|---|---|
| Connector | Terminal | |||
| LH | B17 | 4 | Ground | Existed |
| Center | B18 | 4 | ||
| RH | 2 | |||
Is the inspection result normal?
YES>>GO TO 2
NO>>Repair or replace harness.
CHECK REAR SEAT BELT BUCKLE SWITCH
Check rear seat belt buckle switch. Refer to Component Inspection.
Is the inspection result normal?
YES>>INSPECTION END
NO>>Replace rear seat belt buckle. Refer to Removal & Installation.
Component Inspection
CHECK REAR SEAT BELT BUCKLE SWITCH
Power switch OFF.
Disconnect rear seat belt buckle switch connector.
Check continuity between rear seat belt buckle switch terminals.
Rear seat belt buckle switch Condition Continuity Connector Terminal LH B17 3 4 Rear seat belt (LH) Unfastened Existed Fastened Not existed Center B18 3 4 Rear seat belt (center) Unfastened Existed Fastened Not existed RH 1 2 Rear seat belt (RH) Unfastened Existed Fastened Not existed
Is the inspection result normal?
YES>>INSPECTION END
NO>>Replace rear seat belt buckle. Refer to Removal & Installation.