Removal and Installation
- Reduction Gear Differential Side Oil Seal
- Reduction Gear Air Breather
- Reduction Gear
Reduction Gear Differential Side Oil Seal Nissan Ariya 1st generation
REDUCTION GEAR DIFFERENTIAL SIDE OIL SEAL : Exploded View

| Reduction gear | Side oil seal (left side) | Side oil seal (right side) | |||
REDUCTION GEAR DIFFERENTIAL SIDE OIL SEAL : Removal & Installation
REMOVAL
Remove the front drive shaft (LH side and/or RH side). Refer to FRONT DRIVE SHAFT: Removal & Installation.
Remove side oil seal
(left side and/or right side), using oil seal remover (A) (commercial service tool).

INSTALLATION
Note the following, and install in the reverse order of removal.
Using a drift (commercial service tools), drive the side oil seal
within the dimension (C) and (D) shown as follows.

: Left side 
: Right side Dimension (C) : 2.6 ±0.3 mm (0.102 ±0.012 in) Dimension (D) : 3.45 ±0.3 mm (0.1358 ±0.012 in) Check the oil level and the oil leakage after installation. And check the oil leakage from reduction gear again, after driving the Nissan Ariya vehicle. Refer to REDUCTION GEAR OIL : Inspection.
Reduction Gear Air Breather Nissan Ariya 2023
REDUCTION GEAR AIR BREATHER : Exploded View

| Clip | Air breather hose | Reduction gear |
REDUCTION GEAR AIR BREATHER : Removal & Installation
REMOVAL
Remove high voltage power delivery assembly. Refer to HIGH VOLTAGE POWER DELIVERY ASSEMBLY : Removal & Installation.
Remove air breather hose
and clip
.

INSTALLATION
Note the following, and install in the reverse order of removal.
When installing air breather hose, preventing crush and clogging caused by bending.
Insert the air breather hose all the way to the bulged part of tube.
Reduction Gear Nissan Ariya: FE0
REDUCTION GEAR : Exploded View

| Inverter (front) | Front traction motor | Reduction gear | |||
| Inside of input shaft (insertion part of front traction motor shaft splines) | |||||
REDUCTION GEAR : Unit Removal & Installation
REMOVAL
Drain the gear oil. Refer to REDUCTION GEAR OIL : Draining.
Remove front suspension member assembly, together with reduction gear and front traction motor with inverter (front) from Nissan Ariya vehicle. Refer to FRONT SUSPENSION MEMBER : Removal & Installation.
Remove reduction gear, front traction motor and inverter (front) as a set from front suspension member assembly. Refer to FRONT TRACTION MOTOR : Removal & Installation.
Remove reduction gear air breather hose. Refer to REDUCTION GEAR AIR BREATHER : Removal & Installation.
Remove compressor bracket
, motor mounting LH bracket
, and motor mounting rear bracket
.

Compressor bracket: Refer to Removal & Installation.
Motor mounting LH bracket and motor mounting rear bracket: Refer to FRONT TRACTION MOTOR : Removal & Installation.
Remove the bolts that fasten reduction gear
and front traction motor.

Remove reduction gear
from front traction motor.

INSTALLATION
Note the following, and install in the reverse order of removal.
For each tightening torque, Refer to REDUCTION GEAR : Exploded View.
Check fitting of dowel pins
on front traction motor side of reduction gear installation surface, and remove any moisture, oil, or foreign material from matching surface on front traction motor and reduction gear.
Before installing reduction gear to front traction motor, apply recommended grease to the inside of reduction gear input shaft (insertion part of front traction motor shaft splines), as per the following procedure.
For applying grease, Refer to REDUCTION GEAR : Exploded View.
Clean front traction motor shaft splines and inside of reduction gear input shaft to remove old grease and powder arisen from abrasion.
Inject the specified amount of recommended grease into the reduction gear input shaft back side (greasing part:
).
Specified grease amount : 3.5 ±0.5 g (0.12 ±0.018 oz)
When removing reduction gear from front traction motor, replace O-ring of front traction motor shaft. Refer to FRONT TRACTION MOTOR : Exploded View.
When installing reduction gear
to front traction motor
, align markings
on reduction gear input shaft and front traction motor shaft.

Check the oil level and the oil leakage after installation. Refer to REDUCTION GEAR OIL : Inspection.
When replacing reduction gear, perform adjustment after installation.Refer to REDUCTION GEAR : Adjustment.
REDUCTION GEAR : Adjustment
ADJUSTMENT AFTER INSTALLATION
When replaced reduction gear assembly, perform P position learning of parking actuator. Refer to Work Procedure.