System

In this manual: System
How to Use This Manual — 1Precautions — 1Preparation — 1Vehicle Information — 1Basic Inspection — 1Preparation. Commercial Service Tools Or/and Repair Part — 1Description — 1Component Parts — 1System — 1Diagnosis System (vcm) — 1Ecu Diagnosis Information. Vcm — 1Ev Control System — 1Ev/hev (vcm) — 1Component Parts /circuit Diagnosis — 1Ev Control System — 1Periodic Maintenance. Ev System Warning Lamp — 1Removal and Installation. Vcm — 1Traction Motor System :: Front Traction Motor — 1Preparation — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Traction Motor System :: Rear Traction Motor — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Ev Battery System :: 66kwh Li-Ion Battery — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Disassembly and Assembly — 2Service Data — 1Ev Battery System :: 91kwh Li-Ion Battery — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Disassembly and Assembly — 1Service Data — 2Preparation. Vehicle Charging System — 1Vehicle Charging System :: Description — 1Component Parts — 2System — 1Diagnosis System (on-Board Charger) — 1Diagnosis System (dc/dc Converter) — 1Ecu Diagnosis Information — 1Vehicle Charging System — 1Charger/pd Module (on-Board Charger) — 1Cplc (cplc) — 1Dcdc (dc/dc Converter) — 1Component Parts/circuit Diagnosis — 1Symptom Diagnosis — 1Evse Inspection — 1Periodic Maintenance — 1Removal and Installation — 1Disassembly and Assembly — 1Preparation. High Voltage Cooling System — 1Description — 1Symptom Diagnosis. Overheating Cause Analysis — 1Periodic Maintenance — 1Coolant — 1Removal and Installation — 1Radiator — 1Service Data — 1Removal and Installation. Accelerator Control System — 1Reduction Gear: Re1f62a — 1Removal and Installation — 1Transaxle & Transmission :: Electric Shift — 1Description — 3Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Rear Final Drive: Rn1r62a — 1Removal and Installation — 1Preparation. Front Axle System — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data. Front Drive Shaft — 12wd — 14wd — 1Periodic Maintenance — 1Removal and Installation — 1Preparation. Front Suspension System — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Preparation. Road Wheels & Tires System — 1Description — 1System — 1Ecu Diagnosis Information. Bcm (body Control Module) — 1Tpms — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance. Road Wheels & Tires — 1Removal and Installation — 1Service Data — 1Preparation. Brake System — 1System Description — 1Component Parts — 1Ecu Diagnosis Information. Electrically-Driven Intelligent Brake Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Preparation. Parking Brake System — 1System Description — 1Component Parts — 1System — 1Ecu Diagnosis Information. Abs Actuator and Electric Unit (control Unit) — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Component Parts /circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Brake Control System :: With Vdc — 1System Description — 3Basic Inspection — 2Dtc/circuit Diagnosis — 1Symptom Diagnosis — 2Removal and Installation — 1Brake Control System :: Automatic Brake Hold — 1System Description — 3Component Parts /circuit Diagnosis — 1Removal and Installation — 1Brake Control System :: E-Step — 1System Description — 3Removal and Installation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Symptom Diagnosis — 1Rear Automatic Braking — 1System Description — 1Basic Inspection — 1Preparation. Steering System — 1System Description — 1Component Parts — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance. Steering Wheel — 1Removal and Installation — 1Service Data — 1System Description — 1Component Parts — 1Steering Control System — 1Ecu Diagnosis Information. Power Steering Control Module — 1Dtc/circuit Diagnosis — 1Component Parts /circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation. Power Steering Control Module — 1System Description — 1Removal and Installation — 1System Description — 1System — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Component Parts — 1Basic Inspection — 1Removal and Installation — 1System Description — 1System — 1Ecu Diagnosis Information. Air Bag Diagnosis Sensor Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1System Description. Description. Ventilation System — 1Removal and Installation — 1Preparation. Preparation — 1System Description — 1Basic Inspection — 1Symptom Diagnosis — 1Removal and Installation — 1Electric Compressor — 1Cooler Pipe and Hose — 1A/c Unit Assembly Cover — 1A/c Unit Assembly — 1Heater & Air Conditioning Control System :: Automatic Air Conditioning — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 2Dtc Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 2Preparation. Preparation — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1Preparation. Instrument Panel — 1Component Parts — 1System — 1Ecu Diagnosis Information. Flexible Center Storage Control Module — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Preparation. Preparation — 1Component Parts — 1System — 1Ecu Diagnosis Information. Driver Lumbar Support Control Module — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1System Description — 1System — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Manual Function Does Not Operate — 1Memory Function Does Not Operate — 1Removal and Installation — 1Preparation. Preparation — 1System Description — 1System (intelligent Key System) — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1U2141-87 Can Comm Circuit — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Automatic Back Door Operation Does Not Operate — 1Back Door Does Not Open — 1Door Does Not Lock/unlock with Door Lock and Unlock Switch — 1Removal and Installation — 1Hood — 1Radiator Core Support — 1Charge Port Lid — 1Front Fender — 1Front Door — 1Rear Door — 1Back Door — 1Hood Lock — 1Front Door Lock — 1Rear Door Lock — 1Back Door Lock — 1Outside Key Antenna — 1System Description — 1System — 1Ecu Diagnosis Information. Inverter (front), Inverter (rear), Bcm, Intelligent Key Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Preparation — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Front Passenger Side Power Window Does Not Operate — 1Rear Lh Side Power Window Does Not Operate — 1Rear Rh Side Power Window Does Not Operate — 1Removal and Installation. Power Window Main Switch — 1Preparation. Preparation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Sunroof Switch Assembly — 1Symptom Diagnosis — 1Auto Operation Does Not Operate — 1Removal and Installation — 1Preparation — 1Description — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1Service Information — 6Repair Information — 1Precaution — 1Preparation — 1Removal and Installation — 1Service Data — 1Preparation. Preparation — 1Component Parts — 1System — 1Ecu Diagnosis Information — 1Wiring Diagram. Door Mirror — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Removal and Installation — 1Exterior Lighting System :: Led Headlamp — 1System Description — 3Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance — 1Removal and Installation — 1System Description — 1System — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information. Bcm, Intelligent Key Unit — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis. Interior Lighting System Symptom — 1Removal and Installation — 1Service Data. Bulb Specifications — 1System Description — 1System — 1Ecu Diagnosis Information. Bcm, Ipdm E/r — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1System Description — 1Ecu Diagnosis Information. Bcm — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Preparation. Preparation — 1Removal and Installation. Horn — 1Preparation. Commercial Service Tools Or/and Repair Part — 1System Description — 1Component Parts — 1Ecu Diagnosis Information. Approaching Vehicle Sound for Pedestrians (vsp) Control Unit — 1Approaching Vehicle Sound for Pedestrians (vsp) — 1Vsp [approaching Vehicle Sound for Pedestrians (vsp) Control Unit] — 1Approaching Vehicle Sound for Pedestrians (vsp) System — 1Removal and Installation — 1Removal and Installation — 1Wireless Charger — 1System Description — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Removal and Installation — 1Component Parts — 1System — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information. Bcm — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Can Fundamental — 1Description — 1Trouble Diagnosis — 1Can (controller Area Network) — 1Description — 1
2steps
~12min
5/5difficulty
Done 0 of 2
  • Electric Power Train System
  • Air Conditioner Control
  • Can Communication
  • Charge Port Control
  • Ev System Start up Control
  • High Voltage Power Supply Control
  • Li-Ion Battery Charge Control
  • Motor Power Control
  • Motor Regeneration Control
  • Awd System
  • Power Cut Off Control
  • Ev System Warning
  • Power Limitation Warning
  • Shift P Warning Display
  • Awd Torque Display

Electric Power Train System Nissan Ariya: FE0

System Description

CONTROL OUTLINE

EV requires all electric power source for the system operation.

The power charged in the Li-ion battery is supplied as high-voltage direct current to the high-voltage system. Meanwhile the power is converted by the DC/DC converter and supplied to the 12 V power system.

VCM judges the vehicle status from various information and performs various EV system controls in a comprehensive manner.

Main Control Contents of VCM

ControlReference
EV system start up control Refer to System Description.
High voltage power supply control Refer to System Description.
Power cut off control Refer to System Description.
Motor power control Refer to System Description.
Motor regeneration control Refer to System Description.
AWD system Refer to System Description.
Air conditioner control Refer to System Description.
Li-ion battery charge control Refer to System Description.
Charge port control Refer to System Description.
Motor regeneration control Refer to System Description.
MAC (Message Authentication Code)

MAC (Message Authentication Code) is a function that prevents unauthorized communication from other than the ECU with MAC function by secure authentication communication.

VCM can write a MAC key required for communication between the ECUs and perform MAC diagnosis.

Circuit Diagram

Fail-safe

Fail-safe pattern:

  • Pattern A: Restart is prohibited

  • Pattern B: Traction motor output is limited

  • Pattern C: Quick charge is prohibited

  • Pattern D: Normal charge is prohibited

  • Pattern E: Traction motor output is cut

  • Pattern F: High-voltage system is normally stopped

  • Pattern G: High-voltage system is suddenly stopped

  • Pattern H: A/C control is stopped

FAIL-SAFE LIST

x: applicable

DTC codeTypePatternOthers
ABCDEFGH
P0000 00 × × ×
P0530 16 ×
P0560 61 × × × × × × ×
P0641 16,17 × ×
P0651 16,17 × ×
P0697 16,17 × × × × × × ×
P0AA6 23
  • The insulation resistance of Li-ion battery has decreased: Restart is prohibited

  • The insulation resistance of other than Li-ion battery has decreased: Not applicable

P0AE1 73 ×
P0AE2 72 ×
P0AE2 73 × × ×
P0B33 63 ×
P0CA6 19 ×
P0D0A 11,12,13 ×
P0D11 11,12,13 ×
P1001 78 ×(Nissan Ariya vehicle stopped)
P102C 01 ×
P1033 11 ×
P1035 49 × × × × × × ×
P104B 16,17 ×
P104C 16,17 ×
P12A8 08 Cruse control (ProPILOT Assist/ProPILOT Assist 2.0) operation prohibited
P1596 96 ×(Nissan Ariya vehicle stopped) ×(vehicle stopped)
P1597 F1 ×(Nissan Ariya vehicle stopped)
P159D 23 ×
P15A6 13 × ×
P15A7 31 × ×
P15A9 24 × ×
P15A9 2F ×
P15AA 73 × ×
P15BA 72 × ×
P15BE 96 ×(Nissan Ariya vehicle stopped)
P15BF 96 ×(Nissan Ariya vehicle stopped) ×(vehicle stopped)
P15C5 78 ×(Nissan Ariya vehicle stopped)
P15D3 78 ×(Nissan Ariya vehicle stopped)
P15FA 11,12,13 × ×
P15FB 01 × ×
P15FE 16,17 ×
P15FE 64 × ×
P1604 72,73 × ×
P1605 63 × ×
P160C 04 × × ×
P1613 49 × ×
P161C 49 × × × × × × ×
P161C F1 × × × × × × ×
P161E 96 ×(Nissan Ariya vehicle stopped)
P161F 96 ×(Nissan Ariya vehicle stopped)
P163F 94 × ×
P164B 64 P range is held or N range is indicated
P1666 72 ×
P168A 11 ×
P168B 73 × ×
P168C 72 ×
P168D 11 ×
P168D 12,13 ×
P168D 72 ×
P168E 11 ×
P168E 12,13 ×
P168E 73 ×
P1692 19 ×
P1693 49,87 × × ×
P1694 49,87 × × ×
P1695 96 ×
P1728 19 ×
P1729 98 ×
P3101 61,62 ×
P3194 00,87 Cruse control (ProPILOT Assist/ProPILOT Assist 2.0) operation prohibited
U2370 94,96 ×

Warning / Indicator / Chime List

itemdesignReference
12V battery charge warning lamp For layout, Refer to Design.
For function, Refer to 12V Battery Charge Warning Lamp.
Ready to drive indicator lamp For layout, Refer to Design.
For function, Refer to Ready To Drive Indicator Lamp
Power limitation indicator lamp For layout, Refer to Design.
For function, Refer to Power Limitation Indicator Lamp
EV system warning lamp For layout, Refer to Design.
For function, Refer to EV System Warning Lamp
itemReference
Shift P warning buzzer Refer to Shift P Warning Buzzer.
itemReference
Power limitation warning Refer to System Description.
EV system warning Refer to System Description.
Shift P warning display Refer to System Description.
AWD torque display Refer to System Description.

Air Conditioner Control Nissan Ariya 1st generation

System Description

SYSTEM DIAGRAM

Component partsFunction
IPDM E/R
  • Power switch ON signal is transmitted to VCM

  • Cooling fan speed request signal is received from VCM

On-board charger EVSE connection signal is transmitted to VCM
TCU

The following signals are transmitted to BCM

  • A/C request signal before getting in

  • A/C setting signal before getting in

AV control unit Timer A/C set signal is transmitted to BCM and A/C auto Amp.
BCM
  • The following signals are transmitted to VCM.

    • Wake up request signal

    • Timer A/C request signal

    • A/C setting signal before getting in

  • The following signals are transmitted to A/C auto. Amp.

    • Timer A/C setting time signal

    • A/C request signal before getting in

    • A/C setting signal before getting in

Li-ion battery controller HV battery charge level signal to the VCM.
A/C auto amp.
  • The following signals are received from VCM.

    • Refrigerant pressure signal

    • Wake up request signal

    • Timer A/C request signal

    • Deice permission signal

    • A/C maximum power consumption signal

  • The following signals are transmitted to VCM.

    • Cooling fan speed request signal

    • Timer A/C operation time signal

    • Deice request signal

Charging status indicator Charge state signal is received from VCM
VCM Refer to Component Description.
EV power relay Refer to Component Description.
Refrigerant pressure sensor Refer to Component Description.

DESCRIPTION

In EV, the EV power relay is controlled by VCM so that the air conditioner system can be operated even when the power switch such as timer air conditioner, air conditioner before getting in, and deice control is turned off.

When VCM determines to need starting the air conditioner system by the driver's operation based on timer air conditioner, air conditioner before getting in, and deice control, VCM turns on the EV power relay and supplies power to the air conditioner system.

In addition, VCM calculates the power that can be used by the air conditioner system from the state of Li-ion battery and the state of the Nissan Ariya vehicle, and transmits it to A / C auto amp.

For more information of A/C control, refer to System Description.

DESCRIPTION

TIMER A/C CONTROL

  • When the timer of the timer A/C is ON, BCM reaches the set temperature inside the vehicle* by the scheduled departure time* and activates the timer A/C.

  • While operating time of the timer A/C, two hours before the scheduled departure time, BCM sends a wake up request signal to VCM, VCM activates EV system, and A / C auto amp determines the required operating time from 0 to 1 within the time range based on the outside air temperature and the temperature inside the Nissan Ariya vehicle, and send to BCM. BCM calculates the required operation time sent back from the scheduled departure time and determines the timer A/C start time.

  • For more information on the timer A/C control function,

    refer to Climate Ctrl. Timer (A/C-Heater Timer).

A/C CONTROL BEFORE GETTIN IN

  • When VCM receives A/C request signal before getting in from TCU, VCM activates A/C for 15 to 60 minutes.

  • For more information of A/C control function before getting in,

    refer to Remote Climate Control.

DEICE CONTROL

  • When VCM receives deice request signal from A/C auto amp and is in normal charge mode or quick charge mode, VCM turns on EV power relay and sends deice permission signal (permission) to A/C auto amplifier. A/C auto amp activates deice function upon receiving deice permission signal.

  • If the charge mode ends due to full charge or timer charge end while the deice function is operating, the deice function continues to operate.

  • After completing the compressor operation by the deice control function, VCM activates cooling fan based on cooling fan speed request signal received from A/C auto amp.

  • The deice control function may operate even at the initial stage of timer A/C operation.

  • For more information of the deice control function,

    refer to Heat Pump System Control.

Can Communication Nissan Ariya 2023

System Description

DESCRIPTION

  • CAN (Controller Area Network) is a serial communication line for real time application. It is an on Nissan Ariya vehicle multiplex communication line with high data communication speed and excellent error detection ability. Many electronic control units are equipped onto a Nissan Ariya vehicle, and each control unit shares information and links with other control units during operation (not independent).

    In CAN communication, control units are connected with 2 communication lines (CAN-H line, CAN-L line) allowing a high rate of information transmission with less wiring. Each control unit transmits/receives data but selectively reads required data only.

  • VCM includes a gateway function and communicates signals between the CAN communication circuit and EV system CAN circuit.

  • For CAN communication details, Refer to System Description.

Charge Port Control Nissan Ariya 2023

System Description

SYSTEM DIAGRAM

DESCRIPTION

For charging port control, VCM comprehensively controls the following related to charging according to the Nissan Ariya vehicle status and signals from each switch.

ControlDescription
Charge connector lock/unlock control When the normal charge connector is connected or during normal charging, charge connector is automatically locked and unlocked.
Charge port light control Automatically turns ON/OFF LED lighting inside the charge port.
Charge port lock/unlock control Perform lock /unlock charge port

CHARGE PORT LOCK / UNLOCK CONTROL

Description

The charging connector lock/unlock control automatically locks the charging connector according to the charging scene to prevent tampering during charging.

The VCM determines lock activation and unlock conditions based on signals such as EVSE connection signals received from EVSE, setting information signal received from combination meters via CAN communication, and door lock status signal from BCM.

When the condition is satisfied, the charging connector lock relay is activated to operate the charging connector lock actuator in the closed or open direction to lock/unlock the normal charging connector.

There are the following types of lock modes.

Lock modeFunction
"LOCK" When the normal charge connector is connected, charge connector is automatically locked.
"AUTO"

When charge power supply is not detected even charge connector is locked, or charge connector is locked during normal charge.

(When charge is completed, charge connector is automatically unlocked.)
"UNLOCK" Charge connector is locked when normal charge connector is connected. Charge connector is unlocked when charge power supply is detected.

LOCK OPERATION CONDITION

When the following conditions are satisfied, VCM locks the charge port connector.

"LOCK" mode

  • Select "Charge connector lock" (Vehicle information display): "LOCK" mode

  • Shift position : P range

  • Normal charge connector: Connect (Complete lock)

"AUTO" mode

  • Select "Charge connector lock" (Vehicle information display): "AUTO" mode

  • Shift position : P range

  • Normal charge connector: Connect (Complete lock)

  • When the start normal charge and the charge power supply are not detected

"UNLOCK" mode

  • Select "Charge connector lock" (Vehicle information display): "UNLOCK" mode

  • Shift position : P range

  • Normal charge connector: Connect (Complete lock)

  • When the charge power supply are not detected

"UNLOCK" OPERATION CONDITION

When the following conditions are satisfied, VCM unlocks the charge port connector.

"LOCK" mode

  • When unlock while the door is locked.

  • Select "Charge connector lock" (Nissan Ariya Vehicle information display): "UNLOCK" mode

  • Shift position : Except P range

  • Nissan Ariya Vehicle is READY

"AUTO" mode

  • When unlock while the door is locked.

  • Select "Charge connector lock" (Vehicle information display): "UNLOCK" mode

  • Shift position : Except P range

  • Nissan Ariya Vehicle is READY

  • When the normal charge is completed.

  • When the charge power supply is shut down.

"UNLOCK" mode

  • When unlock while the door is locked.

  • Shift position : Except P range

  • Nissan Ariya Vehicle is READY

  • When the charge power supply is detected. the charge connector is automatically locked again.

OPERATION TIMING CHART

  • "LOCK" MODE

  • "UNLOCK" MODE

OPERATION DESCRIPTION

The swing arm of the charge port lock actuator is inserted into the upper part of the latch at the tip of the normal charge connector, and charge connector is locked by restricting the movement of the latch.

PROCEDURE FOR CHARGE CONNECTOR LOCK / UNLOCK CONTROL ABNORMALITY

When the charge connector lock cannot be unlock automatically, perform the following procedure to unlock manually.

  1. Open the hood

  2. Operate the lock release lever on the back of the charge port base assembly on the normal charge port side in the direction of the arrow in the figure to release the charge port lid lock.

    :Nissan Ariya Vehicle front

CHARGE PORT LIGHT CONTROL

DESCRIPTION

The charge port light control which automatically turns ON the LED illumination inside the port to improve workability while charging.

VCM supplies power to the charge port light and turns ON the LED illumination base on vehicle conditions such as charge port connect /disconnect, door lock/ unlick, driver approach/non-approach, etc.

LIGHT ON CONDITION

When the following all conditions are satisfied, VCM turns ON the charge port light.

  • Vehicle is READY

  • Shift position : P position

  • When ON conditions of the following timer table are satisfied.

LIGHT OFF CONDITION

When the following any condition is satisfied, VCM turns OFF the charge port light.

  • Vehicle is READY

  • Shift position : Except P position

  • When the timer time in the following timer table has passed.

CHARGE PORT LIGHT TIMER TABLE

ControlDescription
When the charge connector is unlocked 3 min.

When the charge lid lock is unlocked

(When the Nissan Ariya vehicle door lock is unlocked, when entering unlock operation condition at approaching)
When the door is opened from closed state.
When the charge connector is removed. *1 30 sec.
When entering auto lock operation condition at getting out from the Nissan Ariya vehicle
When connecting the charge connector 1.5 sec.
When the Nissan Ariya vehicle door is locked during connecting the charge port connector
When the charge connector is locked

*1:If the charging connector is unplugged without holding the intelligent key, the port light may not turn on.

CHARGE PORT LOCK/UNLOCK CONTROL

DESCRIPTION

The VCM receives the door lock status signal from the BCM via CAN communication, activates the charge port lid actuator in conjunction with the door lock / unlock switching, and locks / unlocks the charge port lid.

CHARGE PORT LID LOCK OPERATION CONDITION

When all of the following conditions are satisfied, the VCM locks the charge port lid.

  • When the charge port lid is closed

  • The one of the followings is satisfied.

    • When the Nissan Ariya vehicle door is locked

    • When entering the auto lock operation condition at getting out the Nissan Ariya vehicle.

CHARGE PORT LID UNLOCK OPERATION CONDITION

When the following any condition is satisfied, the VCM unlocks the charge port lid.

  • When the vehicle door is unlocked.

  • When entering the unlock operation condition at approaching to the Nissan Ariya vehicle.

Ev System Start up Control Nissan Ariya: FE0

System Description

SYSTEM DIAGRAM

Component partsFunction
IPDM E/R IPDM E/R transmits the power ON signal to VCM.
BCM

BCM transmits the following signals to VCM

  • READY signal

  • EV system start-up request signal

Charge port (quick charge) Quick charge port transmits the quick charger connecting signal to VCM.
On-board charger

In-Nissan Ariya vehicle charger transmits the following signals to VCM

  • EVSE connection signal

  • EV system start-up request signal

VCM Refer to Component Description.
A/C auto amp. A/C auto amp. transmits the cooling request signal to VCM.
DC/DC converter DC/DC receives converter transmits the start up request signal from VCM
Each relay —

CONTROL DESCRIPTION

VCM judges the operation mode from signals sent by various sensors, switches, and ECUs, and controls the start/stop of the EV system by activating the relays accordingly.

Power Switch ON

When the power supply for power ON is input from the IPDM E/R enters VCM, VCM turns ON each relay to supply power to each ECU and parts of EV system.

READY

When the driver operates the POWER switch while depressing the brake pedal, VCM turns ON each relay to supply power to each ECU and parts of EV system. Furthermore, VCM supplies power to the system main relay.

  • Charge connector is connected.

  • Li-ion battery remaining energy is too low.

  • Li-ion battery temperature is too low. [ -30°C approx. or less ]

In Normal Charging

If VCM judges that the system is in normal charge mode, VCM turns ON each relay to supply power to each ECU of the EV system. Furthermore, VCM supplies power to the system main relay.

In Quick Charging

When VCM judges that the system is in quick charge mode, VCM turns ON each relay to supply power to each ECU of the EV system. Furthermore, Furthermore, VCM supplies power to the quick charge relay and the system main relay.

When Air Conditioner Is Operating (Power OFF)

When air conditioner and its timer, etc., are activated before getting into the vehicle, VCM turns ON each relay to start the EV system. VCM also supplies power of the system main relay and starts A/C system.

In 12V Battery Automatic Charging

When VCM judges that the 12V battery requires automatic charging, VCM turns ON each relay to start the EV system. Furthermore, VCM supplies power the system main relay.

High Voltage Power Supply Control Nissan Ariya: FE0

System Description

SYSTEM DIAGRAM

Component partsFunction
BCM BCM transmits the following signals to VCM.
Charge port (quick charge) Quick charge port transmits the quick charger connecting signal to VCM.
On-board charger

In-Nissan Ariya vehicle charger transmits the following signals to VCM.

  • EVSE connection signal

  • EV system start-up request signal

A/C auto amp. A/C auto amp. transmits the cooling request signal to VCM.
LBC LBC transmits high voltage input permit signal to VCM.
VCM Refer to Component Description.
Pre-charge relay Refer to Component Description.
System main relay 1 Refer to Component Description.
System main relay 2 Refer to Component Description.

DESCRIPTION

When the driver performs the READY operation or connects the charge cable to a charging port, or when VCM starts according to the timer control and judges the necessity of connecting the high voltage circuit to Li-ion battery, VCM activates system main relay 1, system main relay 2, and the pre-charge relay located inside the Li-ion battery junction box and connects high voltage circuit to Li-ion battery.

Moreover, the high voltage circuit of the EV system has a pre-charge circuit to protect the high voltage circuit from sudden application of high voltage current.

CONTROL FLOW

To connect the high voltage circuit, VCM first activates the pre-charge relay and system main relay 2.

As a result, the high voltage power is supplied to the respective systems via the pre-charge resistor in the pre-charge circuit.

VCM activates the system main relay 1 and deactivates the pre-charge relay. Then, normal power is supplied to the respective systems.

Li-Ion Battery Charge Control Nissan Ariya 2026

System Description

CONTROL OUTLINE

  • Li-ion battery charge is controlled by VCM

  • VCM activates the EV system by connecting the charging connector and performing remote control, and starts charging to the Li-ion battery. The following charge modes are available.

Methods of chargingDescription
Li-ion battery charge control Refer to System Description.
Normal charge Immediate charge Refer to System Description.
Timer charge
Remote charge
Quick charge Refer to System Description.
Regeneration charge Refer to System Description.

Motor Power Control Nissan Ariya 2026

System Description

2WD models

SYSTEM DIAGRAM

Component partsFunction
Accelerator pedal position sensor Accelerate pedal position sensor signal is transmitted to VCM
Electric shift control module Electric shift control module transmits shift information to VCM
Inverter (front)

Inverter (front) transmits the following signals to VCM

  • Front motor speed signal

  • Front motor torque limit signal

Front traction motor receives target front motor torque signal from VCM
ABS actuator and electric unit (control unit)

ABS actuator transmits the following signals to VCM

  • ABS operation signal

  • VDC operation signal

  • TCS operation signal

LBC

LBC transmits the following signals to VCM

  • Motor torque limit signal

  • Li-ion battery dischargeable power signal

Electrically-driven intelligent brake unit Electrically-driven intelligent brake unit transmits target braking force signal to VCM.
VCM Refer to Component Description.

DESCRIPTION

The EV system generates traction force by converting the direct current from the Li-ion battery to an alternating current by the inverter (front).

VCM calculates target traction force, based on an accelerator pedal position, vehicle speed, and shift position. After that, VCM adds creep force to the calculated target traction force. Moreover, VCM performs torque limit processing according to the torque limit request from each system, determines target front motor torque signal. and transmits it to the inverter (front) via CAN communication. The inverter (front) applies a current to the motor corresponding to the signal and generates traction force.

In addition, VCM always determines whether the creep force is required to output from the vehicle speed and braking force.

For the operation principle of the motor, Refer to System Description.

OUTPUT LIMIT AND OUTPUT STOP REQUEST LIST

Request ECUOutput limit causePower limitation indicator lampCondition

Inverter (front)

Front traction motor temperature high ON When front traction motor or inverter (front) reaches abnormally high temperature
Input power low ON When high voltage power supply input to inverter (front) is 270V or less.
DTC detected ON Refer to Fail-safe.
Li-ion battery controller (LBC) Li-ion battery remained energy low ON When Li-ion battery cell voltage is low
Li-ion battery temperature high ON When Li-ion battery reaches abnormally high temperature.
Li-ion battery temperature low ON When Li-ion battery reaches an abnormally low temperature.
DTC detected ON Refer to Fail-safe(66kWh LI-ION BATTERY), Fail-safe(91kWh LI-ION BATTERY).
Others ON When none of the above
VCM Accelerator pedal position signal / stop lamp switch signal input error ON When accelerator pedal and brake pedal are judged depressing at the same time
Power train system protection function ON —
DTC detected ON Refer to Fail-safe.

AWD models

SYSTEM DIAGRAM

Component partsFunction
Accelerator pedal position sensor Accelerate pedal position sensor signal is transmitted to VCM
Electric shift control module Electric shift control module transmits shift information to VCM
Inverter (front)

Inverter (front) transmits the following signals to VCM

  • Front motor speed signal

  • Front motor torque limit signal

Front traction motor receives target front motor torque signal from VCM
Inverter (rear)

Inverter (rear) transmits the following signals to VCM.

  • Rear motor speed signal

  • Rear motor torque limit signal

Rear traction motor receives target rear motor torque signal from VCM.
ABS actuator and electric unit (control unit)

ABS actuator transmits the following signals to VCM

  • ABS operation signal

  • VDC operation signal

  • TCS operation signal

LBC

LBC transmits the following signals to VCM

  • Motor torque limit signal

  • Li-ion battery dischargeable power signal

Electrically-driven intelligent brake unit Electrically-driven intelligent brake unit transmits target braking force signal to VCM.
VCM Refer to Component Description.

DESCRIPTION

The EV system generates traction force by converting the direct current from the Li-ion battery to an alternating current by the inverter (front) and inverter (rear).

VCM calculates target traction force, based on an accelerator pedal position, vehicle speed, and shift position. After that, VCM adds creep force to the calculated target traction force. Moreover, VCM performs torque limit processing according to the torque limit request from each system, determines target motor torque signal. and transmits it to the inverter (front) and inverter (rear) via CAN communication. The inverter (front) and inverter (rear) applies a current to the motor corresponding to the signal and generates traction force.

In addition, VCM always determines whether the creep force is required to output from the vehicle speed and braking force.

For the operation principle of the motor, Refer to System Description(Front traction motor), System Description(Rear traction motor).

OUTPUT LIMIT AND OUTPUT STOP REQUEST LIST

Request ECUOutput limit causePower limitation indicator lampCondition
Inverter (front) Front traction motor temperature high ON When front traction motor or inverter (front) reaches abnormally high temperature
Input power low ON When high voltage power supply input to inverter (front) is 270V or less.
DTC detected ON Refer to Fail-safe.
Inverter (rear) Rear traction motor temperature high ON When rear traction motor or inverter (rear) reaches abnormally high temperature
Input power low ON When high voltage power supply input to inverter (rear) is 270V or less.
DTC detected ON Refer to Fail-safe.
Li-ion battery controller (LBC) Li-ion battery remained energy low ON When Li-ion battery cell voltage is low
Li-ion battery temperature high ON When Li-ion battery reaches abnormally high temperature.
Li-ion battery temperature low ON When Li-ion battery reaches an abnormally low temperature.
DTC detected ON Refer to Fail-safe(66kWh LI-ION BATTERY), Fail-safe(91kWh LI-ION BATTERY).
Others ON When none of the above
VCM Accelerator pedal position signal / stop lamp switch signal input error ON When accelerator pedal and brake pedal are judged depressing at the same time
Power train system protection function ON —
DTC detected ON Refer to Fail-safe.

Motor Regeneration Control Nissan Ariya 1st generation

System Description

2WD models

SYSTEM DIAGRAM

Component partsFunction
Accelerator pedal position sensor Transmits accelerator pedal position sensor signal to VCM.
Electric shift control module Transmits shift information to VCM.
Inverter (front)

Inverter (front) transmits the front motor speed signal to VCM.

Receives the following signal from VCM.

  • Regenerative torque command signal

  • Target front motor torque signal

ABS actuator and electric unit (control unit)

Transmits the following signals to VCM.

  • ABS operation signal

  • VDC operation signal

  • TCS operation signal

LBC LBC transmits Li- ion battery chargeable power signal to VCM.
Electrically-driven intelligent brake unit Electrically-driven intelligent brake unit transmits target braking force signal to VCM and receives regenerative torque signal from VCM.
VCM Refer to Component Description.

DESCRIPTION

The front traction motor which is normally used as traction force, is operated as a generator during deceleration to charge Li-ion battery. At the same time the rotational resistance of the generator is utilizes as braking force.

For the operation principle, Refer to System Description.

REGENERATIVE BRAKE CONTROL

When the brake pedal is depressed while driving, the target braking force signal is transmitted from the electrically-driven intelligent brake unit to VCM within the range of the regenerative torque signal transmitted from VCM. VCM calculates the target regenerative torque from the signal and transmits the target front motor torque signal to the inverter (front). Further, the electrically-driven intelligent brake unit receives the regenerative torque signal so that thebraking force can comprehensively be controlled.

REGENERATION CHARGE CONTROL

VCM determines the regenerative charging amount from the Li-ion battery maximum chargeable power signal sent from the Li-ion battery. Moreover, VCM determines the energy recovery amount while performing a collaborative control with the electrically-driven intelligent brake system so that a suitable braking force is provided according to the brake pedal operation amount.

After determining the energy recovery amount, VCM transmits a regenerative torque command signal to the inverter (front) and starts regeneration charge.

AWD models

SYSTEM DIAGRAM

Component partsFunction
Accelerator pedal position sensor Transmits accelerator pedal position sensor signal to VCM.
Electric shift control module Transmits shift information to VCM.
Inverter (front)

Inverter (front) transmits the front motor speed signal to VCM.

Receives the following signal from VCM.

  • Regenerative torque command signal

  • Target front motor torque signal

Inverter (rear)

Inverter (rear) transmits the rear motor speed signal to VCM.

Receives the following signal from VCM.

  • Regenerative torque command signal

  • Target rear motor torque signal

ABS actuator and electric unit (control unit)

Transmits the following signals to VCM.

  • ABS operation signal

  • VDC operation signal

  • TCS operation signal

LBC LBC transmits Li- ion battery chargeable power signal to VCM.
Electrically-driven intelligent brake unit Electrically-driven intelligent brake unit transmits target braking force signal to VCM and receives regenerative torque signal from VCM.
VCM Refer to Component Description.

DESCRIPTION

The front traction motor and rear traction motor which is normally used as traction force, is operated as a generator during deceleration to charge Li-ion battery. At the same time the rotational resistance of the generator is utilizes as braking force.

For the operation principle, Refer to System Description(Front traction motor), System Description(Rear traction motor).

REGENERATIVE BRAKE CONTROL

When the brake pedal is depressed while driving, the target braking force signal is transmitted from the electrically-driven intelligent brake unit to VCM within the range of the regenerative torque signal transmitted from VCM. VCM calculates the target regenerative torque from the signal and transmits the target motor torque signal to the inverter (front) and inverter (rear).Further, the electrically-driven intelligent brake unit receives the regenerative torque signal so that thebraking force can comprehensively be controlled.

REGENERATION CHARGE CONTROL

VCM determines the regenerative charging amount from the Li-ion battery maximum chargeable power signal sent from the Li-ion battery. Moreover, VCM determines the energy recovery amount while performing a collaborative control with the electrically-driven intelligent brake system so that a suitable braking force is provided according to the brake pedal operation amount.

After determining the energy recovery amount, VCM transmits a regenerative torque command signal to the inverter (front) and inverter (rear) and starts regeneration charge.

Awd System Nissan Ariya SUV

System Description

SYSTEM DIAGRAM

Component partsFunction
VCM

Based on each signal (Nissan Ariya vehicle status) obtained from each C/U and sensor, the following signals are transmitted to the inverter (front) and the inverter (rear).

  • Target front motor torque signal

  • Target rear motor torque signal

Inverter (front) Receive the target front motor torque signal from VCM, and operate the front traction motor.
Inverter (rear) Receive the target rear motor torque signal from VCM, and operate the rear traction motor.

DESCRIPTION

  • The VCM estimates the status of the vehicle based on the signals from each C/U and sensor, and controls the optimum front and rear traction force distribution in real time. Taking advantage that the front and rear wheels are 100% electrically driven, the front and rear traction force can be controlled in real time at electrical response speed according to the operation and condition of the Nissan Ariya vehicle.

    The vehicle's attitude is stabilized and performance is improved by estimating changes in vehicle behavior in advance, such as when accelerating or turning, and controlling the traction force distribution to the front and rear wheels without delay.

  • The front and rear traction force distribution during driving can be checked with the AWD torque display. Refer to System Description.

  • The characteristics are changed to the optimum traction force distribution according to the selected drive mode. For the drive mode refer to System Description.

Traction force distribution characteristics at each drive mode

Drive mode
STANDARD ECO SPORT SNOW
Automatic switching between electric power consumption priority (front wheel main)and driving performance priority. Automatic switching between electric power consumption priority (front wheel main)and driving performance priority. Driving performance priority Driving performance priority on the snow covered road.

Power Cut Off Control Nissan Ariya 1st generation

System Description

SYSTEM DIAGRAM

Component partsFunction
Air bag diagnosis sensor unit

The following signals are transmitted to VCM

  • Nissan Ariya Vehicle collision detection information

  • Vehicle light collision detection signal

System main relay 1 Refer to Component Description.
System main relay 2 Refer to Component Description.

DESCRIPTION

Because EV uses high voltage power, there is a risk of electric shock if the high voltage circuit is shorted to a body ground during a collision. To avoid such risks, if VCM detects a car crush information signal, VCM deactivates the system main relay to cut off the Li-ion battery from the high voltage circuit so that the risk of electric shock is reduced.

When detecting a serious collision

When receiving a car crash information signal from the air bag diagnosis sensor unit, VCM turns OFF the system main relay and quickly interrupts the high voltage circuit. When DTC clear signal is received, restart becomes possible.

When detection a minor collision

When receiving a slight collision detection signal from the air bag diagnosis sensor unit, VCM turns OFF the system main relay and quickly interrupts the high voltage circuit. In this case when the power switch is turned OFF, restart becomes possible.

Ev System Warning Nissan Ariya

System Description

Design/Purpose

EV system warning warns the driver that EV system is not normal.

SymbolMessageEV system warningDescription
ONBlink
Service EV System ○ —

Operating Condition : DTC detected

Nissan Ariya Vehicle Condition : EV system error (No need to vehicle stop)

Service EV System

Stop safely
— ○

Operating Condition : DTC detected

Nissan Ariya Vehicle Condition : EV system error (Vehicle is driving, Need to vehicle stop)

Service EV System

Power reduced
○ —

Operating Condition : DTC detected

Nissan Ariya Vehicle Condition : EV system error (No need to vehicle stop, Output is limited)

Service EV System

Power reduced

Stop safely
— ○

Operating Condition : DTC detected

Nissan Ariya Vehicle Condition : EV system error (Vehicle is driving, Need to vehicle stop, Output is limited)

Service EV System

Unable to restart after power off
○ —

Operating Condition : DTC detected

Nissan Ariya Vehicle Condition : EV system error (Restart not possible)
EV System off ○ —

Operating Condition : DTC detected

Nissan Ariya Vehicle Condition : EV system error (Vehicle stop, P range, Cut off the high voltage circuit)

EV System off

Stop safely

— ○

Operating Condition : DTC detected

Nissan Ariya Vehicle Condition : EV system error (Vehicle is driving, Cut off the high voltage circuit)

Service EV System

Apply parking brake
○ —

Operating Condition : DTC detected

Nissan Ariya Vehicle Condition : EV system error (Vehicle stop, Except P range, Cut off the high voltage circuit)

SYNCHRONIZATION WITH MASTER WARNING LAMP

Applicable

For master warning lamp, Refer to Master Warning Lamp.

SYSTEM DIAGRAM

2WD models

AWD models

SIGNAL PATH

  • If VCM detects a malfunction or receives DTC signals from each ECU, VCM transmits EV system warning lamp request signal to the combination meter via CAN communication.

  • Combination meter indicates EV system warning in the Nissan Ariya vehicle information display according to the input signal.

When all of the following conditions are satisfied:

  • Power switch: ON or READY

  • EV system-related DTC is detected.

For DTCs that EV system warning lamp turns ON, refer to following table.
Control unitReference page
VCM Refer to DTC Index.
  • On-board charger

  • DC/DC converter

Refer to DTC Index.

Refer to DTC Index.
Inverter (front) Refer to DTC Index.
Inverter (rear) Refer to DTC Index.
Li-ion battery controller Refer to DTC Index(66kWh LI-ION BATTERY), DTC Index(91kWh LI-ION BATTERY).

When any of the following conditions are satisfied:

  • Power switch: OFF

  • DTC is erased.

TIMING CHART

Power Limitation Warning Nissan Ariya SUV

System Description

2WD models

Design/Purpose

Power limitation warning shows that front traction motor output is limited below the threshold value.

SymbolMessageDescription

EV system hot

Power reduced

Drive slowly

Operating Condition : Power limitation indicator lamp turns ON

Nissan Ariya Vehicle Condition : EV system temperature high

EV system cold

Power reduced

Operating Condition : Power limitation indicator lamp turns ON

Nissan Ariya Vehicle Condition : EV system temperature low

Battery charge is low

Power reduced

Charge now

Operating Condition : Power limitation indicator lamp turns ON

Nissan Ariya Vehicle Condition : Li-ion battery remained energy low
Power reduced

Operating Condition : Power limitation indicator lamp turns ON

Nissan Ariya Vehicle Condition : Other

SYNCHRONIZATION WITH MASTER WARNING LAMP

Synchronization is applied.

For master warning lamp, Refer to Master Warning Lamp.

SYSTEM DIAGRAM

SIGNAL PATH

  • If the front drive motor needs to be protected, the inverter (front) limits the motor torque and transmits a signal to VCM.

  • When Li-ion battery cannot output the power normally, LBC limits the output and transmits signals to VCM.

  • The inverter (front) transmits the front traction motor temperature. The LBC transmits the remaining Li-ion battery charge level, the maximum Li-ion battery temperature, and the minimum Li-ion battery temperature. Using these signals, when the value falls below the threshold value, VCM transmits an output limit indicator light signal and a separate lighting reason signal (output limit warning display signal) to the combination meter.

  • The combination meter turns on the output limit indicator lamp by the signal input, and displays the output limit indicator lights up reason is in the Nissan Ariya vehicle information displays.

INDICATOR OPERATING CONDITION

When output limit indicator lamp is turned ON. Refer to System Description.

INDICATOR OPERATION CANCEL CONDITION

The front traction motor or Li-ion battery recovers from the output limit condition.

AWD models

Design/Purpose

Power limitation warning shows that front traction motor and rear traction motor output is limited below the threshold value.

SymbolMessageDescription
-

EV system cooling

Temporary Power

Reduction*

Operating Condition : Power limitation indicator lamp turns OFF

Nissan Ariya Vehicle Condition : EV system temperature high

EV system hot

Power reduced

Drive slowly

Operating Condition : Power limitation indicator lamp turns ON

Nissan Ariya Vehicle Condition : EV system temperature high

EV system cold

Power reduced

Operating Condition : Power limitation indicator lamp turns ON

Nissan Ariya Vehicle Condition : EV system temperature low

Battery charge is low

Power reduced

Charge now

Operating Condition : Power limitation indicator lamp turns ON

Nissan Ariya Vehicle Condition : Li-ion battery remained energy low
Power reduced

Operating Condition : Power limitation indicator lamp turns ON

Nissan Ariya Vehicle Condition : Other

*: May not indicate depend on the vehicle spec.

SYNCHRONIZATION WITH MASTER WARNING LAMP

Synchronization is applied.

For master warning lamp, Refer to Master Warning Lamp.

SYSTEM DIAGRAM

SIGNAL PATH

  • If the front traction motor and rear traction motor needs to be protected, the inverter (front) and inverter (rear) limits the motor torque and transmits a signal to VCM.

  • When Li-ion battery cannot output the power normally, LBC limits the output and transmits signals to VCM.

  • The inverter (front) and inverter (rear) transmits the front traction motor and rear traction motor temperature. The LBC transmits the remaining Li-ion battery charge level, the maximum Li-ion battery temperature, and the minimum Li-ion battery temperature. Using these signals, when the value falls below the threshold value, VCM transmits an output limit indicator light signal and a separate lighting reason signal (output limit warning display signal) to the combination meter.

  • The combination meter turns on the output limit indicator lamp by the signal input, and displays the output limit indicator lights up reason is in the Nissan Ariya vehicle information displays.

INDICATOR OPERATING CONDITION

When output limit indicator lamp is turned ON. Refer to System Description.

INDICATOR OPERATION CANCEL CONDITION

The front traction motor and rear traction motor or Li-ion battery recovers from the output limit condition.

Shift P Warning Display Nissan Ariya SUV

System Description

DESIGN/PURPOSE

It warns the driver that he/she is trying to get out of the vehicle with the gear shift being placed at other than the P range.

SymbolMessage
Shift P position

SYNCHRONIZATION WITH MASTER WARNING LAMP

Applicable

For master warning lamp, Refer to Master Warning Lamp.

SYNCHRONIZATION WITH WARNING CHIME

Synchronization is applied. (Shift P warning chime)

For warning chime, Refer to Shift P Warning Buzzer

SYSTEM DIAGRAM

SIGNAL PATH

  • Electric shift control module transmits shift position information to VCM.

  • BCM transmits a door switch signal to VCM.

  • VCM judges the Nissan Ariya vehicle condition according to shift position information and a door switch signal. When the driver's door is opened with the shift position except P position, a warning indicator signal for forgetting to return to P position is transmitted to the combination meter.

INDICATOR OPERATING CONDITION

When all of the following conditions are satisfied:

  • Shift position: Except P range

  • Front door (driver side): Open

INDICATOR CANCEL CONDITION

The indication is cancelled when any of the following conditions are satisfied:

  • The shift position is changed to P position.

  • The driver’s door is closed.

TIMING CHART

Awd Torque Display Nissan Ariya SUV

System Description

DESIGN/PURPOSE

DesignPurpose
Displays the drive torque to the front and rear wheels while driving and informs the driver of this.