2wd
- Preparation. Rear Axle System
- Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting
- Periodic Maintenance. Rear Wheel Hub
- Removal and Installation. Rear Wheel Hub
Preparation. Rear Axle System Nissan Ariya SUV
REAR AXLE SYSTEM : Commercial Service Tools or/and Repair Part
| Tool name | Description | |
|---|---|---|
| Ball joint remover | ![]() |
Removing hub bolt |
Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting Nissan Ariya 2026
NVH Troubleshooting Chart
Use chart below to find the cause of the symptom. If necessary, repair or replace these parts.
| Possible cause and suspected parts | Symptom | Reference | |||||
|---|---|---|---|---|---|---|---|
| REAR AXLE | |||||||
| Noise | Shake | Vibration | Shimmy | Judder | Poor quality ride or handling | ||
| Improper installation, looseness | × | × | × | × | × | × | Removal and Installation |
| Parts interference | × | × | × | × | — | × | — |
| Wheel bearing damage | × | × | × | — | — | — | Periodic Maintenance Operation |
| REAR AXLE | × | × | × | × | × | × | — |
| REAR SUSPENSION | × | × | × | × | × | × | — |
| TIRE | × | × | × | × | × | × | NVH in WT section |
| ROAD WHEEL | × | × | — | × | × | × | NVH in WT section |
| BRAKE | × | × | — | × | × | — | NVH in BR section |
×: Applicable, —: Not applicable
Periodic Maintenance. Rear Wheel Hub Nissan Ariya first Gen
REAR WHEEL HUB : Periodic Maintenance Operation
COMPONENT PART
Check the mounting conditions (looseness, back lash) of each component and component conditions (wear, damage) are normal.
WHEEL HUB ASSEMBLY (BEARING-INTEGRATED TYPE)
Check the following items, and replace the part it necessary.
Move wheel hub assembly in the axial direction by hand. Check there is no looseness of wheel bearing.
| Axial end play | : Refer to Wheel Bearing. |
Rotate wheel hub assembly and check there is no unusual noise or other irregular conditions. If there is any of irregular conditions, replace wheel hub assembly.
Removal and Installation. Rear Wheel Hub Nissan Ariya first Gen
REAR WHEEL HUB : Exploded View

| Axle housing | Hub cap | Back plate | |||
| Hub bolt | Wheel hub and bearing assembly | Disc rotor | |||
| : Nissan Ariya Vehicle front | |||||
| : N·m (kg-m, ft-lb) | |||||
| : Always replace after every disassembly. | |||||
REAR WHEEL HUB : Removal & Installation
REMOVAL
Remove tires. Refer to Exploded View.
Remove parking brake actuator harness and rear wheel sensor harness. Refer to Removal & Installation.
Remove caliper assembly. Hang caliper assembly in a place where it will not interfere with work. Refer to Exploded View.
Remove disc rotor and wheel hub assembly. If disc rotor is reused, put align marks
on wheel hub and disc rotor before removing the disc rotor.

Remove mounting bolts
of wheel hub.

Remove wheel hub, back plate, and hub cap.
Remove radius rod. Refer to Removal & Installation.
Remove front lower link. Refer to Removal & Installation.
Remove coil spring. Refer to Removal & Installation.
Remove rear suspension arm mounting bolt
and nut
from axle housing
.

Separate axle housing from rear suspension arm.
Remove hub bolt
from wheel hub assembly with ball remover (commercial tool) (A).

Perform inspection after removal. Refer to Inspection.
INSTALLATION
Note the following, and install in the reverse order of removal.
Set a washer
to hub bolt
and install hub bolt by using the tightening force of nut
.
When reusing disc rotor and wheel hub assembly, align marks
put during removal of them.
Perform inspection after installation. Refer to Inspection.
REAR WHEEL HUB : Inspection
INSPECTION AFTER Removal
Check component parts for deformation, crack, and damage, replace malfunction parts if necessary.
INSPECTION AFTER INSTALLATION
When replacing disc rotor, check it for runout. Refer to Periodic Maintenance.
Check wheel sensor harness for proper connection. Refer to Exploded View.
Check wheel alignment. Refer to Inspection.
Adjust neutral position of steering angle sensor. Refer to Work Procedure.
