Basic Inspection

Brake Control System

In this manual: Basic Inspection
How to Use This Manual — 1Precautions — 1Preparation — 1Vehicle Information — 1Basic Inspection — 1Preparation. Commercial Service Tools Or/and Repair Part — 1Description — 1Component Parts — 1System — 1Diagnosis System (vcm) — 1Ecu Diagnosis Information. Vcm — 1Ev Control System — 1Ev/hev (vcm) — 1Component Parts /circuit Diagnosis — 1Ev Control System — 1Periodic Maintenance. Ev System Warning Lamp — 1Removal and Installation. Vcm — 1Traction Motor System :: Front Traction Motor — 1Preparation — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Traction Motor System :: Rear Traction Motor — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Ev Battery System :: 66kwh Li-Ion Battery — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Disassembly and Assembly — 2Service Data — 1Ev Battery System :: 91kwh Li-Ion Battery — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Disassembly and Assembly — 1Service Data — 2Preparation. Vehicle Charging System — 1Vehicle Charging System :: Description — 1Component Parts — 2System — 1Diagnosis System (on-Board Charger) — 1Diagnosis System (dc/dc Converter) — 1Ecu Diagnosis Information — 1Vehicle Charging System — 1Charger/pd Module (on-Board Charger) — 1Cplc (cplc) — 1Dcdc (dc/dc Converter) — 1Component Parts/circuit Diagnosis — 1Symptom Diagnosis — 1Evse Inspection — 1Periodic Maintenance — 1Removal and Installation — 1Disassembly and Assembly — 1Preparation. High Voltage Cooling System — 1Description — 1Symptom Diagnosis. Overheating Cause Analysis — 1Periodic Maintenance — 1Coolant — 1Removal and Installation — 1Radiator — 1Service Data — 1Removal and Installation. Accelerator Control System — 1Reduction Gear: Re1f62a — 1Removal and Installation — 1Transaxle & Transmission :: Electric Shift — 1Description — 3Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Rear Final Drive: Rn1r62a — 1Removal and Installation — 1Preparation. Front Axle System — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data. Front Drive Shaft — 12wd — 14wd — 1Periodic Maintenance — 1Removal and Installation — 1Preparation. Front Suspension System — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Preparation. Road Wheels & Tires System — 1Description — 1System — 1Ecu Diagnosis Information. Bcm (body Control Module) — 1Tpms — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance. Road Wheels & Tires — 1Removal and Installation — 1Service Data — 1Preparation. Brake System — 1System Description — 1Component Parts — 1Ecu Diagnosis Information. Electrically-Driven Intelligent Brake Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Preparation. Parking Brake System — 1System Description — 1Component Parts — 1System — 1Ecu Diagnosis Information. Abs Actuator and Electric Unit (control Unit) — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Component Parts /circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Brake Control System :: With Vdc — 1System Description — 3Basic Inspection — 2Dtc/circuit Diagnosis — 1Symptom Diagnosis — 2Removal and Installation — 1Brake Control System :: Automatic Brake Hold — 1System Description — 3Component Parts /circuit Diagnosis — 1Removal and Installation — 1Brake Control System :: E-Step — 1System Description — 3Removal and Installation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Symptom Diagnosis — 1Rear Automatic Braking — 1System Description — 1Basic Inspection — 1Preparation. Steering System — 1System Description — 1Component Parts — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance. Steering Wheel — 1Removal and Installation — 1Service Data — 1System Description — 1Component Parts — 1Steering Control System — 1Ecu Diagnosis Information. Power Steering Control Module — 1Dtc/circuit Diagnosis — 1Component Parts /circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation. Power Steering Control Module — 1System Description — 1Removal and Installation — 1System Description — 1System — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Component Parts — 1Basic Inspection — 1Removal and Installation — 1System Description — 1System — 1Ecu Diagnosis Information. Air Bag Diagnosis Sensor Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1System Description. Description. Ventilation System — 1Removal and Installation — 1Preparation. Preparation — 1System Description — 1Basic Inspection — 1Symptom Diagnosis — 1Removal and Installation — 1Electric Compressor — 1Cooler Pipe and Hose — 1A/c Unit Assembly Cover — 1A/c Unit Assembly — 1Heater & Air Conditioning Control System :: Automatic Air Conditioning — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 2Dtc Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 2Preparation. Preparation — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1Preparation. Instrument Panel — 1Component Parts — 1System — 1Ecu Diagnosis Information. Flexible Center Storage Control Module — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Preparation. Preparation — 1Component Parts — 1System — 1Ecu Diagnosis Information. Driver Lumbar Support Control Module — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1System Description — 1System — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Manual Function Does Not Operate — 1Memory Function Does Not Operate — 1Removal and Installation — 1Preparation. Preparation — 1System Description — 1System (intelligent Key System) — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1U2141-87 Can Comm Circuit — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Automatic Back Door Operation Does Not Operate — 1Back Door Does Not Open — 1Door Does Not Lock/unlock with Door Lock and Unlock Switch — 1Removal and Installation — 1Hood — 1Radiator Core Support — 1Charge Port Lid — 1Front Fender — 1Front Door — 1Rear Door — 1Back Door — 1Hood Lock — 1Front Door Lock — 1Rear Door Lock — 1Back Door Lock — 1Outside Key Antenna — 1System Description — 1System — 1Ecu Diagnosis Information. Inverter (front), Inverter (rear), Bcm, Intelligent Key Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Preparation — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Front Passenger Side Power Window Does Not Operate — 1Rear Lh Side Power Window Does Not Operate — 1Rear Rh Side Power Window Does Not Operate — 1Removal and Installation. Power Window Main Switch — 1Preparation. Preparation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Sunroof Switch Assembly — 1Symptom Diagnosis — 1Auto Operation Does Not Operate — 1Removal and Installation — 1Preparation — 1Description — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1Service Information — 6Repair Information — 1Precaution — 1Preparation — 1Removal and Installation — 1Service Data — 1Preparation. Preparation — 1Component Parts — 1System — 1Ecu Diagnosis Information — 1Wiring Diagram. Door Mirror — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Removal and Installation — 1Exterior Lighting System :: Led Headlamp — 1System Description — 3Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance — 1Removal and Installation — 1System Description — 1System — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information. Bcm, Intelligent Key Unit — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis. Interior Lighting System Symptom — 1Removal and Installation — 1Service Data. Bulb Specifications — 1System Description — 1System — 1Ecu Diagnosis Information. Bcm, Ipdm E/r — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1System Description — 1Ecu Diagnosis Information. Bcm — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Preparation. Preparation — 1Removal and Installation. Horn — 1Preparation. Commercial Service Tools Or/and Repair Part — 1System Description — 1Component Parts — 1Ecu Diagnosis Information. Approaching Vehicle Sound for Pedestrians (vsp) Control Unit — 1Approaching Vehicle Sound for Pedestrians (vsp) — 1Vsp [approaching Vehicle Sound for Pedestrians (vsp) Control Unit] — 1Approaching Vehicle Sound for Pedestrians (vsp) System — 1Removal and Installation — 1Removal and Installation — 1Wireless Charger — 1System Description — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Removal and Installation — 1Component Parts — 1System — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information. Bcm — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Can Fundamental — 1Description — 1Trouble Diagnosis — 1Can (controller Area Network) — 1Description — 1
78steps
~468min
5/5difficulty
Done 0 of 78
  • Diagnosis and Repair Work Flow
  • Additional Service When Replacing Abs Actuator and Electric Unit (control Unit)
  • Configuration [abs Actuator and Electric Unit (control Unit)]
  • Adjustment of Steering Angle Sensor Neutral Position
  • Calibration of G Sensor
  • Adjustment of Initial Position
  • Removal/replacement of Rear Brake Pad or Rear Brake Caliper
  • Change of System Mode

Diagnosis and Repair Work Flow Nissan Ariya 2023

Work Flow

DETAILED FLOW

INTERVIEW FROM THE CUSTOMER

Clarify customer complaints before inspection. First of all, perform an interview utilizing diagnostic work sheet and reproduce the symptom as well as fully understand it. Ask customer about his/her complaints carefully. Check symptoms by driving Nissan Ariya vehicle with customer, if necessary. Refer to Diagnostic Work Sheet.

>>

GO TO 2.

CHECK SYMPTOM

Reproduce the symptom that is indicated by the customer, based on the information from the customer obtained by interview. Also check that the symptom is not caused by fail-safe mode. Refer to Fail-safe.

>>

GO TO 3.

PERFORM THE SELF-DIAGNOSIS

With CONSULT

  1. Power switch OFF (Auto ACC is ON).

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Power switch ON without depressing the brake pedal.

  4. Perform self-diagnosis for “ABS”.

Is DTC detected?

YES>>

Record or print self-diagnosis results and freeze frame data (FFD). GO TO 4.

NO>>

GO TO 6.

PERFORM DTC DIAGNOSIS PROCEDURE

With CONSULT

  1. Erase self-diagnostic results for “ABS”.

  2. Power switch OFF (Auto ACC is ON).

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Perform confirmation procedures for the error-detected system.

Is DTC detected?

YES>>

GO TO 5.

NO>>

Check harness and connectors based on the information obtained by interview. Refer to Intermittent Incident.

REPAIR OR REPLACE ERROR-DETECTED PART

With CONSULT

  1. Repair or replace error-detected parts.

  2. Reconnect part or connector after repairing or replacing.

  3. When DTC is detected, erase self-diagnostic result for “ABS”.

>>

GO TO 7.

IDENTIFY ERROR-DETECTED SYSTEM BY SYMPTOM DIAGNOSIS

Estimate error-detected system based on symptom diagnosis and perform inspection.

Can the error-detected system be identified?

YES>>

GO TO 7.

NO>>

Check harness and connectors based on the information obtained by interview. Refer to Intermittent Incident.

FINAL CHECK

With CONSULT

  1. Check the reference value for “ABS”.

  2. Recheck the symptom and check that the symptom is not reproduced on the same conditions.

Is the symptom reproduced?

YES>>

GO TO 3.

NO>>

INSPECTION END

Diagnostic Work Sheet

Description

  • In general, customers have their own criteria for a problem. Therefore, it is important to understand the symptom and status well enough by asking the customer about his/her concerns carefully. To systemize all the information for the diagnosis, prepare the interview sheet referring to the interview points.

  • In some cases, multiple conditions that appear simultaneously may cause a DTC to be detected.

INTERVIEW SHEET SAMPLE

Interview sheet
Customer nameMR/MSRegistration numberInitial year registration
Nissan Ariya Vehicle typeVIN
Storage dateEngine / Traction motorMileagekm (Mile)
Symptom □ Does not operate ( ) function

□ Warning lamp turns ON.

□□□□□□□□□

□ Other (
)
□ Noise (Location: ) □ Vibration (Location: )
□ Other ( )
First occurrence □ Recently □ Other ( )
Frequency of occurrence □ Always □ Under a certain conditions of □ Sometimes ( time(s)/day)
Climate conditions □ Irrelevant
Weather □ Fine □ Cloud □ Rain □Snow □ Others ( )
Temperature □ Hot □Warm □ Cool □ Cold □ Temperature [Approx. °C (°F)]
Relative humidity □ High □ Moderate □ Low
Road conditions □ Ordinary road □ Highway □ Mountainous road (uphill or downhill) □ Rough road
Operating condition, etc.

□ Irrelevant

□ When engine/traction motor starts □ During idling

□ During driving □ During acceleration □ At constant speed driving

□ During deceleration

□ Immediately before stop [Nissan Ariya Vehicle speed: Approx. km/h (MPH)]

□ During cornering (right curve or left curve)

□ When steering wheel is steered (to right or to left)
Other conditions VDC setting status □ On □ Off

Use of other functions

(ex. ICC)
□ Yes □ No ( )
Presence of non-genuine parts installation □ Yes □ No ( )
Memo

Additional Service When Replacing Abs Actuator and Electric Unit (control Unit) Nissan Ariya 2023

Work Procedure

Description

Vehicle specification needs to be written with CONSULT because it is not written after replacing the ABS actuator and electric unit (control unit).

For details the operation, refer to “CONSULT Operation Manual”.

WRITING VEHICLE SPECIFICATION

With CONSULT

Perform writing Nissan Ariya vehicle specification to ABS actuator and electric unit (control unit) according to "Replace ECU" in CONSULT Operation Manual.

>>

GO TO 2.

PERFORM NECESSARY WORK

With CONSULT

  1. Perform configuration. Refer to Work Procedure.

  2. Perform air bleeding. Refer to BRAKE FLUID : Air Bleeding.

  3. Perform calibration of decel G sensor. Refer to Work Procedure.

  4. Perform calibration of side G sensor. Refer to Work Procedure.

  5. Perform adjustment of initialization position. Refer to Work Procedure.

  6. Perform self-diagnosis for “All DTC Reading”.

  7. Erase the memory of self-diagnosis results.

  8. Actual driving 3 km or more.

>>

WORK END

Configuration [abs Actuator and Electric Unit (control Unit)] Nissan Ariya 2023

Work Procedure

Vehicle specification needs to be written with CONSULT because it is not written after replacing the ABS actuator and electric unit (control unit).

For details the operation, refer to “CONSULT Operation Manual”.

WRITING VEHICLE SPECIFICATION

With CONSULT

Perform writing Nissan Ariya vehicle specification to ABS actuator and electric unit (control unit) according to "Replace ECU" in CONSULT Operation Manual.

>>

WORK END

Adjustment of Steering Angle Sensor Neutral Position Nissan Ariya first Gen

Work Procedure

Always adjust the neutral position of steering angle sensor before driving when the following operation is performed.

×: Required —: Not required

ProcedureAdjust the neutral position of steering angle sensor
Removing/ installing ABS actuator and electric unit (control unit) —
Replacing ABS actuator and electric unit (control unit) —
Removing/installing steering angle sensor ×
Replacing steering angle sensor ×
Removing/installing steering components ×
Replacing steering components ×
Removing/installing front suspension components ×
Replacing front suspension components ×
Removing/installing tire —
Replacing tire —
Tire rotation —
Adjusting front wheel alignment. ×

CHECK THE VEHICLE STATUS (1)

Stop vehicle with front wheels in the straight-ahead position.

Does the Nissan Ariya vehicle stay in the straight-ahead position?

YES>>

GO TO 2.

NO>>

Steer the steering wheel to the straight-ahead position. Stop the Nissan Ariya vehicle.

ADJUST NEUTRAL POSITION OF STEERING ANGLE SENSOR

With CONSULT

  1. Power switch ON.

  2. Select “ABS”, “Work support” and “Steering angle sensor adjustment” in this order.

  3. Select “START”.

  4. After approximately 10 seconds, select “END”.

  5. Power switch OFF, and then turn it ON again.

>>

GO TO 3.

CHECK DATA MONITOR (1)

With CONSULT

  1. The Nissan Ariya vehicle is either pointing straight ahead, or the vehicle needs to be moved. Stop when it is pointing straight ahead.

  2. Select “ABS”, “Data monitor”, and “Steering angle” in the order. Check that the signal is within the specified value. Refer to Diagnosis Description.

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

GO TO 4.

CHECK STEERING COMPONENT PARTS

Check the installation condition of steering component parts. Refer to STEERING WHEEL : Periodic Maintenance Operation.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace error-detected parts. GO TO 5.

CHECK FRONT SUSPENSION COMPONENT PARTS

Check the installation condition of front suspension component parts. Refer to FRONT SUSPENSION ASSEMBLY : Periodic Maintenance Operation.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace error-detected parts. GO TO 6.

CHECK FRONT WHEEL ALIGNMENT

Check the front wheel alignment. Refer to WHEEL ALIGNMENT : Inspection.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Adjust the front wheel alignment. Refer to WHEEL ALIGNMENT : Adjustment. GO TO 7.

CHECK THE Nissan Ariya Vehicle STATUS (2)

Stop vehicle with front wheels in the straight-ahead position.

Does the Nissan Ariya vehicle stay in the straight-ahead position?

YES>>

GO TO 8.

NO>>

Steer the steering wheel to the straight-ahead position. GO TO 8.

CHECK DATA MONITOR (2)

With CONSULT

  1. The Nissan Ariya vehicle is either pointing straight ahead, or the vehicle needs to be moved. Stop when it is pointing straight ahead.

  2. Select “ABS”, “Data monitor”, and “Steering angle” in the order. Check that the signal is within the specified value. Refer to Diagnosis Description.

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

GO TO 9.

CHECK DATA MONITOR (3)

With CONSULT

  1. The Nissan Ariya vehicle is either pointing straight ahead, or the vehicle needs to be moved.

  2. The Nissan Ariya vehicle is either pointing straight ahead, or the vehicle needs to be moved. Stop when it is pointing straight ahead.

  3. Select “ABS”, “Data monitor”, and “Steering angle” in the order. Check that the signal is within the specified value. Refer to Diagnosis Description.

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

GO TO 1.

ERASE SELF-DIAGNOSIS MEMORY

With CONSULT

  1. Record or print self-diagnosis results and freeze frame data (FFD).

  2. Erase self-diagnosis result for "ABS".

Are the memories erased?

YES>>

End of work.

NO>>

Check the DTC. Refer to DTC Index.

EPS SYSTEM LEARNING

  1. Pull the parking brake switch.

  2. Power switch OFF.

  3. Get out of the Nissan Ariya vehicle and close all doors.

  4. Wait 65 seconds.

  5. Set the Nissan Ariya vehicle to READY.

>>

WORK END

Calibration of G Sensor Nissan Ariya 2023

Work Procedure

Always perform the decel G sensor calibration and side G sensor calibration before driving when the following operation is performed.

×: Required —: Not required

Procedure
  • Decel G sensor calibration

  • Side G sensor calibration

Removing/ installing ABS actuator and electric unit (control unit) ×
Replacing ABS actuator and electric unit (control unit) ×
Removing/installing steering components —
Replacing steering components —
Removing/installing front suspension components —
Replacing front suspension components —
Removing/installing tire —
Replacing tire —
Tire rotation —
Adjusting front wheel alignment. —

CHECK THE VEHICLE STATUS

  1. Steer the steering wheel to the straight-ahead position. Stop the Nissan Ariya vehicle on level surface.

  2. Power switch OFF.

Is the vehicle stopped in the straight-ahead position on level surface?

YES>>

GO TO 2.

NO>>

Steer the steering wheel to the straight-ahead position. Stop the Nissan Ariya vehicle on level surface.

PERFORM DECEL G SENSOR CALIBRATION, SIDE G SENSOR CALIBRATION

With CONSULT

  1. Power switch ON.

  2. Select “ABS”, “Work support”, “Decel G sensor calibration” in this order.

  3. Select “START”.

  4. After approximately 10 seconds, select “END”.

  5. Select “ABS”, “Work support”, “Side G sensor calibration” in this order.

  6. Select “START”.

  7. After approximately 10 seconds, select “END”.

>>

GO TO 3.

CHECK DATA MONITOR

With CONSULT

  1. Drive the Nissan Ariya vehicle. Steer the steering wheel to the straight-ahead position. Stop the vehicle on level surface.

  2. Select “ABS”, “Data monitor”, “Decel G sensor” and “Side G sensor” in this order. Check that the signal is within the specified value. Refer to Values On The Diagnosis Tool.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

GO TO 1.

ERASE SELF-DIAGNOSIS MEMORY

With CONSULT

  1. Record or print self-diagnosis results and freeze frame data (FFD).

  2. Erase self-diagnosis result for "ABS".

Are the memories erased?

YES>>

INSPECTION END

NO>>

Check the DTC. Refer to DTC Index.

Adjustment of Initial Position Nissan Ariya SUV

Work Procedure

×: Required —: not required

ProcedureInitialization position adjustment
Removing/ installing ABS actuator and electric unit (control unit) —
Replacing ABS actuator and electric unit (control unit) ×
Removing/ installing rear brake pad (When not pressing piston of rear brake caliper assembly) —
Removing/ installing rear brake pad (When pressing piston of rear brake caliper assembly) ×
Replacing rear brake pad ×
Removing/ installing rear brake caliper assembly —
Replacing rear brake caliper assembly ×
Replacing rear disc rotor ×
Removing/ installing parking brake switch —
Replacing parking brake switch —

PERFORM INITIALIZATION POSITION ADJUSTMENT

  1. Select "ABS", "Work support", and "Initialization position adjustment" according to this order.

  2. Touch "START".

>>

GO TO 2.

PERFORM THE SELF-DIAGNOSIS

With CONSULT

  1. Power switch OFF (Auto ACC function ON).

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Power switch ON without depressing the brake pedal.

  4. Erase self-diagnosis results for "ABS".

  5. Pull parking brake switch to activate electric parking brake.

  6. Push parking brake switch to release electric parking brake.

  7. Perform self-diagnosis for “ABS”.

Is malfunction detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

INSPECTION END

Removal/replacement of Rear Brake Pad or Rear Brake Caliper Nissan Ariya 2023

Work Procedure

×: Required —: not required

Procedure
  • Start brake pad replacement

  • Finish brake pad replacement

  • Initialization position adjustment

Removing/installing ABS actuator and electric unit (control unit) —
Replacing ABS actuator and electric unit (control unit) —
Removing/installing rear brake pad (When not pressing piston of rear brake caliper assembly) —
Removing/installing rear brake pad (When pressing piston of rear brake caliper assembly) ×
Replacing rear brake pad ×
Removing/installing rear brake caliper assembly —
Replacing rear brake caliper assembly ×
Replacing rear disc rotor ×
Removing/installing parking brake switch —
Replacing parking brake switch —

BEFORE REMOVAL/REPLACEMENT OF REAR BRAKE PAD OR REAR CALIPER ASSEMBLY

With CONSULT

  1. Power switch OFF to ON.

  2. Select “ABS”, “Work support”, and “Start brake pad replacement” according to this order.

  3. Touch “START”.

>>

GO TO 2.

REMOVAL AND INSTALLATION/REPLACEMENT OF REAR BRAKE PAD OR REAR BRAKE CALIPER ASSEMBLY

Replace the rear brake pad or rear brake caliper.

  • Rear brake pad: Refer to REAR BRAKE PAD : Removal & Installation.

  • Rear brake caliper assembly: Refer to REAR BRAKE CALIPER ASSEMBLY : Removal & Installation.

>>

GO TO 3.

AFTER INSTALLATION/REPLACEMENT OF REAR BRAKE PAD OR REAR CALIPER ASSEMBLY

With CONSULT

  1. Select “ABS”, “Work support”, and “Finish brake pad replacement” according to this order.

  2. Touch “START”.

>>

GO TO 4.

PERFORM THE SELF-DIAGNOSIS

With CONSULT

  1. Pull parking brake switch to activate electric parking brake.

  2. Push parking brake switch to release electric parking brake.

  3. Perform self-diagnosis for “ABS”.

Is malfunction detected?

YES>>

Check the DTC. Refer to DTC Index. GO TO 5.

NO>>

GO TO 5.

CHECK DATA MONITOR

With CONSULT

Select “ABS”, “Data monitor”, “Brake force (left)” and “Brake force (right)” according to this order. Check that signals are within the specified value. Refer to Values On The Diagnosis Tool.

Is the check result normal?

YES>>

GO TO 6.

NO>>

GO TO 1.

ERASE SELF-DIAGNOSIS MEMORY

With CONSULT

  1. Power switch OFF to ON.

  2. Erase self-diagnosis results for “ABS”.

Is the memory erased?

YES>>

INSPECTION END

NO>>

Check the DTC. Refer to DTC Index.

Change of System Mode Nissan Ariya first Gen

Work Procedure

×: Required —: not required

ProcedureSystem mode change
Removing/installing ABS actuator and electric unit (control unit) —
Replacing ABS actuator and electric unit (control unit) —
Removing/installing rear brake pad (When not pressing piston of rear brake caliper assembly) —
Replacing rear brake caliper assembly —
Removing/installing parking brake switch —
Replacing parking brake switch —
When the system mode needs to be changed from “On” to “Off” 〇

CHANGE OF SYSTEM MODE

With CONSULT

  1. Select “ABS”, “Work support”, and “System mode change” according to this order.

  2. Touch “Off”.

>>

GO TO 2.

PERFORM THE SELF-DIAGNOSIS

With CONSULT

  1. Pull parking brake switch to activate electric parking brake.

  2. Push parking brake switch to release electric parking brake.

  3. Perform self-diagnosis for “ABS”.

Is malfunction detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

INSPECTION END