Disassembly and Assembly

Busbar

In this manual: Disassembly and Assembly
How to Use This Manual — 1Precautions — 1Preparation — 1Vehicle Information — 1Basic Inspection — 1Preparation. Commercial Service Tools Or/and Repair Part — 1Description — 1Component Parts — 1System — 1Diagnosis System (vcm) — 1Ecu Diagnosis Information. Vcm — 1Ev Control System — 1Ev/hev (vcm) — 1Component Parts /circuit Diagnosis — 1Ev Control System — 1Periodic Maintenance. Ev System Warning Lamp — 1Removal and Installation. Vcm — 1Traction Motor System :: Front Traction Motor — 1Preparation — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Traction Motor System :: Rear Traction Motor — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Ev Battery System :: 66kwh Li-Ion Battery — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Disassembly and Assembly — 2Service Data — 1Ev Battery System :: 91kwh Li-Ion Battery — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Disassembly and Assembly — 1Service Data — 2Preparation. Vehicle Charging System — 1Vehicle Charging System :: Description — 1Component Parts — 2System — 1Diagnosis System (on-Board Charger) — 1Diagnosis System (dc/dc Converter) — 1Ecu Diagnosis Information — 1Vehicle Charging System — 1Charger/pd Module (on-Board Charger) — 1Cplc (cplc) — 1Dcdc (dc/dc Converter) — 1Component Parts/circuit Diagnosis — 1Symptom Diagnosis — 1Evse Inspection — 1Periodic Maintenance — 1Removal and Installation — 1Disassembly and Assembly — 1Preparation. High Voltage Cooling System — 1Description — 1Symptom Diagnosis. Overheating Cause Analysis — 1Periodic Maintenance — 1Coolant — 1Removal and Installation — 1Radiator — 1Service Data — 1Removal and Installation. Accelerator Control System — 1Reduction Gear: Re1f62a — 1Removal and Installation — 1Transaxle & Transmission :: Electric Shift — 1Description — 3Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Rear Final Drive: Rn1r62a — 1Removal and Installation — 1Preparation. Front Axle System — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data. Front Drive Shaft — 12wd — 14wd — 1Periodic Maintenance — 1Removal and Installation — 1Preparation. Front Suspension System — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Preparation. Road Wheels & Tires System — 1Description — 1System — 1Ecu Diagnosis Information. Bcm (body Control Module) — 1Tpms — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance. Road Wheels & Tires — 1Removal and Installation — 1Service Data — 1Preparation. Brake System — 1System Description — 1Component Parts — 1Ecu Diagnosis Information. Electrically-Driven Intelligent Brake Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Preparation. Parking Brake System — 1System Description — 1Component Parts — 1System — 1Ecu Diagnosis Information. Abs Actuator and Electric Unit (control Unit) — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Component Parts /circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Brake Control System :: With Vdc — 1System Description — 3Basic Inspection — 2Dtc/circuit Diagnosis — 1Symptom Diagnosis — 2Removal and Installation — 1Brake Control System :: Automatic Brake Hold — 1System Description — 3Component Parts /circuit Diagnosis — 1Removal and Installation — 1Brake Control System :: E-Step — 1System Description — 3Removal and Installation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Symptom Diagnosis — 1Rear Automatic Braking — 1System Description — 1Basic Inspection — 1Preparation. Steering System — 1System Description — 1Component Parts — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance. Steering Wheel — 1Removal and Installation — 1Service Data — 1System Description — 1Component Parts — 1Steering Control System — 1Ecu Diagnosis Information. Power Steering Control Module — 1Dtc/circuit Diagnosis — 1Component Parts /circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation. Power Steering Control Module — 1System Description — 1Removal and Installation — 1System Description — 1System — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Component Parts — 1Basic Inspection — 1Removal and Installation — 1System Description — 1System — 1Ecu Diagnosis Information. Air Bag Diagnosis Sensor Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1System Description. Description. Ventilation System — 1Removal and Installation — 1Preparation. Preparation — 1System Description — 1Basic Inspection — 1Symptom Diagnosis — 1Removal and Installation — 1Electric Compressor — 1Cooler Pipe and Hose — 1A/c Unit Assembly Cover — 1A/c Unit Assembly — 1Heater & Air Conditioning Control System :: Automatic Air Conditioning — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 2Dtc Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 2Preparation. Preparation — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1Preparation. Instrument Panel — 1Component Parts — 1System — 1Ecu Diagnosis Information. Flexible Center Storage Control Module — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Preparation. Preparation — 1Component Parts — 1System — 1Ecu Diagnosis Information. Driver Lumbar Support Control Module — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1System Description — 1System — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Manual Function Does Not Operate — 1Memory Function Does Not Operate — 1Removal and Installation — 1Preparation. Preparation — 1System Description — 1System (intelligent Key System) — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1U2141-87 Can Comm Circuit — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Automatic Back Door Operation Does Not Operate — 1Back Door Does Not Open — 1Door Does Not Lock/unlock with Door Lock and Unlock Switch — 1Removal and Installation — 1Hood — 1Radiator Core Support — 1Charge Port Lid — 1Front Fender — 1Front Door — 1Rear Door — 1Back Door — 1Hood Lock — 1Front Door Lock — 1Rear Door Lock — 1Back Door Lock — 1Outside Key Antenna — 1System Description — 1System — 1Ecu Diagnosis Information. Inverter (front), Inverter (rear), Bcm, Intelligent Key Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Preparation — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Front Passenger Side Power Window Does Not Operate — 1Rear Lh Side Power Window Does Not Operate — 1Rear Rh Side Power Window Does Not Operate — 1Removal and Installation. Power Window Main Switch — 1Preparation. Preparation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Sunroof Switch Assembly — 1Symptom Diagnosis — 1Auto Operation Does Not Operate — 1Removal and Installation — 1Preparation — 1Description — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1Service Information — 6Repair Information — 1Precaution — 1Preparation — 1Removal and Installation — 1Service Data — 1Preparation. Preparation — 1Component Parts — 1System — 1Ecu Diagnosis Information — 1Wiring Diagram. Door Mirror — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Removal and Installation — 1Exterior Lighting System :: Led Headlamp — 1System Description — 3Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance — 1Removal and Installation — 1System Description — 1System — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information. Bcm, Intelligent Key Unit — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis. Interior Lighting System Symptom — 1Removal and Installation — 1Service Data. Bulb Specifications — 1System Description — 1System — 1Ecu Diagnosis Information. Bcm, Ipdm E/r — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1System Description — 1Ecu Diagnosis Information. Bcm — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Preparation. Preparation — 1Removal and Installation. Horn — 1Preparation. Commercial Service Tools Or/and Repair Part — 1System Description — 1Component Parts — 1Ecu Diagnosis Information. Approaching Vehicle Sound for Pedestrians (vsp) Control Unit — 1Approaching Vehicle Sound for Pedestrians (vsp) — 1Vsp [approaching Vehicle Sound for Pedestrians (vsp) Control Unit] — 1Approaching Vehicle Sound for Pedestrians (vsp) System — 1Removal and Installation — 1Removal and Installation — 1Wireless Charger — 1System Description — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Removal and Installation — 1Component Parts — 1System — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information. Bcm — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Can Fundamental — 1Description — 1Trouble Diagnosis — 1Can (controller Area Network) — 1Description — 1
~19min read
  • 2wd
  • Awd

2wd Nissan Ariya

Exploded View

DISASSEMBLY

Busbar 2 Busbar 3 Busbar 4
Busbar 5 Busbar 6 Busbar 7
Busbar 8 Busbar 15 Busbar 16
Busbar 17 Busbar 18 Busbar 19
Nut cap
: N·m (kg-m, in-lb)

BUSBAR LAYOUT

Busbar 1 Busbar 2 Busbar 3
Busbar 4 Busbar 5 Busbar 6
Busbar 7 Busbar 8 Busbar 9
Busbar 10 Busbar 11 Busbar 12
Busbar 13 Busbar 14 Busbar 15
Busbar 16 Busbar 17 Busbar 18
Busbar 19 Busbar 20
: Service bracket ASSY

Disassembly & Assembly

DANGER:

Because hybrid vehicles and electric vehicles contain a high voltage battery, there is a risk of electric shock, electric leakage, or similar accidents if the Nissan Ariya vehicle is handled incorrectly. Be sure to follow the correct work procedures when performing inspection and maintenance.

ENVIRONMENT FOR LI-ION BATTERY DISASSEMBLY WORK

Must be an indoor environment.

  • The environment must utilize a shutter or other means to shut out the outside environment and prevent rain, snow, dust, or other substances from entering.

  • The environment must not cause the intrusion of sweat during work, or cause condensation to occur due to high temperature or humidity.

Metal powder, grease, and other foreign substances must not enter.

  • The indoor environment must also prevent metal powder, grease, and other foreign substances from entering due to maintenance performed on other Nissan Ariya vehicles and other sources during disassembly work.

  • During disassembly without internal work, temporarily close the battery pack upper case or cover it with an insulating cover.

The floor must be dry.

  • The floor must not be wet as a result of factors such as Nissan Ariya vehicle entry during rain or snow.

Work space

  • The work space must be approximately the size of one entire Nissan Ariya vehicle.

  • Take appropriate countermeasures so that persons other than the operator do not enter the work space, such as by placing signs indicating that disassembly work is in progress.

Standard fire fighting equipment

  • Always place a standard fire fighting equipment in the disassembly work area.

  • Depending on type of fire (Nissan Ariya vehicle or battery) use standard fire fighting equipment (water or extinguisher).

Busbar 1 and Busbar 20:

Refer to Disassembly & Assembly.

Busbar 8 and Busbar 13:

Refer to Disassembly & Assembly.

Busbar 2 and Busbar 19:

Disassembly

Remove nut cap .

Remove nut and then remove busbar 2 .

Remove busbar 19 in the same way.

Assembly

Note the following items, and assemble in the reverse order of disassembly.

DANGER:
  • There is the danger of electric shock caused by contact with the terminals. Be sure to wear insulated protective gear and use insulated tools.

  • Because there is a danger of electric shock and fire, never allow bus bar to contact a wrong terminal.

    • If bus bar contacts a wrong terminal, the circuit becomes energized and a short may occur.

    • Always keep the busbar cover closed until immediately before the installation of busbar.

Busbar 3, Busbar 4, Busbar 17 and Busbar 18:

Disassembly

Remove bolts and then remove busbar 3 .

Remove the other busbars in the same way.

Assembly

Note the following items, and assemble in the reverse order of disassembly.

DANGER:
  • There is the danger of electric shock caused by contact with the terminals. Be sure to wear insulated protective gear and use insulated tools.

  • Because there is a danger of electric shock and fire, never allow bus bar to contact a wrong terminal.

    • If bus bar contacts a wrong terminal, the circuit becomes energized and a short may occur.

    • Always keep the bus bar cover closed until immediately before the installation of bus bar.

Busbar 5 and Busbar 16:

Disassembly

Remove bracket .

: Bolts

Remove bolts and then remove busbar 5.

Remove busbar 16 in the same way.

Assembly

Note the following items, and assemble in the reverse order of disassembly.

DANGER:
  • There is the danger of electric shock caused by contact with the terminals. Be sure to wear insulated protective gear and use insulated tools.

  • Because there is a danger of electric shock and fire, never allow bus bar to contact a wrong terminal.

    • If bus bar contacts a wrong terminal, the circuit becomes energized and a short may occur.

    • Always keep the bus bar cover closed until immediately before the installation of bus bar.

Busbar 6, Busbar 7, Busbar 14 and Busbar 15:

Disassembly

Remove controller mounting plate. Refer to Removal & Installation.

Remove bolts and then remove busbar 6 .

Remove the other busbats in the same way.

Assembly

Note the following items, and assemble in the reverse order of disassembly.

DANGER:
  • There is the danger of electric shock caused by contact with the terminals. Be sure to wear insulated protective gear and use insulated tools

  • Because there is a danger of electric shock and fire, never allow bus bar to contact a wrong terminal.

    • If bus bar contacts a wrong terminal, the circuit becomes energized and a short may occur.

    • Always keep the bus bar cover closed until immediately before the installation of bus bar.

Awd Nissan Ariya first Gen

Exploded View

FRONT POWER SUPPLY

DISASSEMBLY

Busbar 2 Busbar 3 Busbar 4
Busbar 5 Busbar 6 Busbar 7
Busbar 8 Busbar 9 Busbar 10
Busbar 11 Busbar 15 Busbar 16
Busbar 17 Busbar 18 Busbar 19
Busbar 20 Busbar 21 Busbar 22
Busbar 23 Nut cap
: N·m (kg-m, in-lb)

BUSBAR LAYOUT

Busbar 1 Busbar 2 Busbar 3
Busbar 4 Busbar 5 Busbar 6
Busbar 7 Busbar 8 Busbar 9
Busbar 10 Busbar 11 Busbar 12
Busbar 13 Busbar 14 Busbar 15
Busbar 16 Busbar 17 Busbar 18
Busbar 19 Busbar 20 Busbar 21
Busbar 22 Busbar 23 Busbar 24
: Around Service bracket
: Rear module stack 2nd floor

REAR POWER SUPPLY

DISASSEMBLY

Busbar 41 Busbar 42 Busbar 43
Busbar 44 Busbar 45 Busbar 46
Busbar 47 Nut cap
: N·m (kg-m, in-lb)
Busbar 41 Busbar 42 Busbar 43
Busbar 44 Busbar 45 Busbar 46
Busbar 47

Disassembly & Assembly

DANGER:

Because hybrid vehicles and electric vehicles contain a high voltage battery, there is a risk of electric shock, electric leakage, or similar accidents if the Nissan Ariya vehicle is handled incorrectly. Be sure to follow the correct work procedures when performing inspection and maintenance.

ENVIRONMENT FOR LI-ION BATTERY DISASSEMBLY WORK

Must be an indoor environment.

  • The environment must utilize a shutter or other means to shut out the outside environment and prevent rain, snow, dust, or other substances from entering.

  • The environment must not cause the intrusion of sweat during work, or cause condensation to occur due to high temperature or humidity.

Metal powder, grease, and other foreign substances must not enter.

  • The indoor environment must also prevent metal powder, grease, and other foreign substances from entering due to maintenance performed on other Nissan Ariya vehicles and other sources during disassembly work.

  • During disassembly without internal work, temporarily close the battery pack upper case or cover it with an insulating cover.

The floor must be dry.

  • The floor must not be wet as a result of factors such as Nissan Ariya vehicle entry during rain or snow.

Work space

  • The work space must be approximately the size of one entire Nissan Ariya vehicle.

  • Take appropriate countermeasures so that persons other than the operator do not enter the work space, such as by placing signs indicating that disassembly work is in progress.

Standard fire fighting equipment

  • Always place a standard fire fighting equipment in the disassembly work area.

  • Depending on type of fire (Nissan Ariya vehicle or battery) use standard fire fighting equipment (water or extinguisher).

busbar 1 and busbar 24

Refer to Disassembly & Assembly.

busbar 12 to busbar 14

Refer to Disassembly & Assembly.

busbar 2 and busbar 23

DISASSEMBLY

Remove nut cap .

Remove nut and bolt , and then remove busbar 2 .

Remove busbar 23 in the same way.

Assembly

Note the following items, and assemble in the reverse order of disassembly.

DANGER:
  • There is the danger of electric shock caused by contact with the terminals. Be sure to wear insulated protective gear and use insulated tools.

  • Because there is a danger of electric shock and fire, never allow bus bar to contact a wrong terminal.

    • If bus bar contacts a wrong terminal, the circuit becomes energized and a short may occur.

    • Always keep the busbar cover closed until immediately before the installation of busbar .

busbar 3, busbar 4, busbar 21 and busbar 22

DISASSEMBLY

Remove bolts and then remove busbar 3 .

Remove the other busbar s in the same way.

Assembly

Note the following items, and assemble in the reverse order of disassembly.

DANGER:
  • There is the danger of electric shock caused by contact with the terminals. Be sure to wear insulated protective gear and use insulated tools.

  • Because there is a danger of electric shock and fire, never allow bus bar to contact a wrong terminal.

    • If bus bar contacts a wrong terminal, the circuit becomes energized and a short may occur.

    • Always keep the bus bar cover closed until immediately before the installation of bus bar.

busbar 5 and busbar 20

DISASSEMBLY

Remove bracket .

: Bolts

Remove bolts and then remove busbar 5.

Remove busbar 20 in the same way.

Assembly

Note the following items, and assemble in the reverse order of disassembly.

DANGER:
  • There is the danger of electric shock caused by contact with the terminals. Be sure to wear insulated protective gear and use insulated tools.

  • Because there is a danger of electric shock and fire, never allow bus bar to contact a wrong terminal.

    • If bus bar contacts a wrong terminal, the circuit becomes energized and a short may occur.

    • Always keep the bus bar cover closed until immediately before the installation of bus bar.

busbar 6, busbar 7, busbar 18 and busbar 19

DISASSEMBLY

Remove the battery upper floor assembly. Refer to Disassembly & Assembly.

Remove bolt and nut. And then remove busbar 7

Remove the bolt. and then remove busbar 6.

Remove other busbar in the same way.

Assembly

Note the following items, and assemble in the reverse order of disassembly.

DANGER:
  • There is the danger of electric shock caused by contact with the terminals. Be sure to wear insulated protective gear and use insulated tools.

  • Because there is a danger of electric shock and fire, never allow bus bar to contact a wrong terminal.

    • If bus bar contacts a wrong terminal, the circuit becomes energized and a short may occur.

    • Always keep the bus bar cover closed until immediately before the installation of bus bar.

busbar 8 and busbar 17

DISASSEMBLY

Remove the battery upper floor assembly. Refer to Disassembly & Assembly.

Remove the bolt . And then busbar 8 .

Remove busbar 17 in the same way.

Assembly

Note the following items, and assemble in the reverse order of disassembly.

DANGER:
  • There is the danger of electric shock caused by contact with the terminals. Be sure to wear insulated protective gear and use insulated tools.

  • Because there is a danger of electric shock and fire, never allow bus bar to contact a wrong terminal.

    • If bus bar contacts a wrong terminal, the circuit becomes energized and a short may occur.

    • Always keep the bus bar cover closed until immediately before the installation of bus bar.

busbar 9

DISASSEMBLY

Remove the battery upper floor assembly. Refer to Disassembly & Assembly.

Remove busbar 8 and busbar 17.

Remove the bracket bolt and . And then move the harness to keep the work space.

Remove the bolt. And then busbar 9.

Assembly

Note the following items, and assemble in the reverse order of disassembly.

DANGER:
  • There is the danger of electric shock caused by contact with the terminals. Be sure to wear insulated protective gear and use insulated tools.

  • Because there is a danger of electric shock and fire, never allow bus bar to contact a wrong terminal.

    • If bus bar contacts a wrong terminal, the circuit becomes energized and a short may occur.

    • Always keep the bus bar cover closed until immediately before the installation of bus bar.

busbar 10 and busbar 16

DISASSEMBLY

Remove service plug bracket. Refer to Disassembly & Assembly.

Remove the bolt and nut. And then remove busbar 10.

Remove busbar 16 in the same way.

Assembly

Note the following items, and assemble in the reverse order of disassembly.

DANGER:
  • There is the danger of electric shock caused by contact with the terminals. Be sure to wear insulated protective gear and use insulated tools.

  • Because there is a danger of electric shock and fire, never allow bus bar to contact a wrong terminal.

    • If bus bar contacts a wrong terminal, the circuit becomes energized and a short may occur.

    • Always keep the bus bar cover closed until immediately before the installation of bus bar.

busbar 11 and busbar 15

DISASSEMBLY

Remove the bolt. And then busbar 11.

Remove busbar 15 in the same way.

Assembly

Note the following items, and assemble in the reverse order of disassembly.

DANGER:
  • There is the danger of electric shock caused by contact with the terminals. Be sure to wear insulated protective gear and use insulated tools.

  • Because there is a danger of electric shock and fire, never allow bus bar to contact a wrong terminal.

    • If bus bar contacts a wrong terminal, the circuit becomes energized and a short may occur.

    • Always keep the bus bar cover closed until immediately before the installation of bus bar.

busbar 41, busbar 42, 46 and busbar 47

DISASSEMBLY

Remove nut cap .

Open the busbar cover and remove nut and bolt. And then remove busbar 41.

Remove busbar 47 in the same way.

Open the busbar cover and remove bolt . And then remove busbar 42 .

Remove busbar 46 in the same way.

Assembly

Note the following items, and assemble in the reverse order of disassembly.

DANGER:
  • There is the danger of electric shock caused by contact with the terminals. Be sure to wear insulated protective gear and use insulated tools.

  • Because there is a danger of electric shock and fire, never allow bus bar to contact a wrong terminal.

    • If bus bar contacts a wrong terminal, the circuit becomes energized and a short may occur.

    • Always keep the busbar cover closed until immediately before the installation of busbar.

busbar 43, busbar 44, and busbar 45

DISASSEMBLY

Remove the battery upper floor assembly. Refer to Disassembly & Assembly.

Remove busbar 6, busbar 7, busbar 8, busbar 9, busbar 17, busbar 18 and busbar 19

Remove nut cap .

Open the busbar cover and remove nut and bolt . And then remove busbar 43 and busbar 45 .

Remove nut cap .

Remove nut and bolt . And then remove busbar 44 .

Assembly

Note the following items, and assemble in the reverse order of disassembly.

DANGER:
  • There is the danger of electric shock caused by contact with the terminals. Be sure to wear insulated protective gear and use insulated tools.

  • Because there is a danger of electric shock and fire, never allow bus bar to contact a wrong terminal.

    • If bus bar contacts a wrong terminal, the circuit becomes energized and a short may occur.

    • Always keep the busbar cover closed until immediately before the installation of busbar.