Rear Motor Control [inverter (rear)]
- P030a-62 Ignition a Control Signal
- P0a1c-01 Drive Motor B Control Module
- P0a1c-05 Drive Motor B Control Module
- P0a30-11 Drive Motor B Temperature Sensor
- P0a30-4b Drive Motor B Temperature Sensor
- P0a45-04 Drive Motor B Position Sensor
- P0a79-62 Drive Motor B Inverter
- P0a8b-A2 14 Volt Power Module System Voltage
- P0af2-4b Drive Motor Inverter Temperature Sensor B
- P2d3b-92 Hybrid/ev Discharge System
- P3081-44 Resolver Offset Value Error
- P30e5-04 Drive Motor B Coolant Pump
- P30e6-11 Drive Motor B Excitation Current
- P30e6-12 Drive Motor B Excitation Current
- P30e7-01 Drive Motor B Excitation Current Sensor
- U2143-82 Can Comm Circuit
P030a-62 Ignition a Control Signal Nissan Ariya first Gen
DTC Description
DTC DETECTION LOGIC
| DTC | CONSULT screen terms | DTC detection condition | ||
|---|---|---|---|---|
| P030A | 62 | Ignition A Control Signal | Diagnosis condition | At inverter (rear) start or READY state |
| Signal | Power SW signal | |||
| Threshold | There was a difference between the power SW signal input by hard wire to the inverter (rear) and the power SW signal which receives by CAN signal. | |||
| Diagnosis delay time | Within 2 seconds | |||
POSSIBLE CAUSE
Wiring harness or connector (disconnection or short circuit in the power switch signal circuit)
Power switch signal (CAN signal)
Inverter (rear)
FAIL-SAFE
—
Confirmation Procedure
PREPARATION BEFORE OPERATION
If another "Confirmation Procedure" was performed immediately before this task, always power switch OFF, exit the Nissan Ariya vehicle and close all doors (including the back door), and wait for at least 60 seconds until the combination meter turns off before starting the next test.
>>GO TO 2.
PERFORM THE DTC CONFIRMATION PROCEDURE
With CONSULT
Power switch ON and wait at least 10 seconds.
Check the DTC.
Is "P030A-62" detected?
YES>>Refer to DTC Diagnosis Procedure.
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
INSPECTION OF THE CAN COMMUNICATION
Inspect the CAN communication circuit. Refer to Trouble Diagnosis Flow Chart.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace the malfunctioning parts.
INSPECTION OF THE HARNESS CONNECTOR
Power switch OFF.
Check mating conditions of the harness connector for the inverter (rear).
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair or replace the malfunctioning parts.
INSPECTION OF THE CONNECTOR TERMINAL
Disconnect the harness connector of the inverter (rear).
Check the inverter (rear) connector for water intrusion, or damage or corrosion of the terminals.
Is the inspection result normal?
YES>>GO TO 4.
NO>>Repair or replace the malfunctioning parts.
INSPECTION OF POWER SWITCH CIRCUIT 1
Power switch ON.
Check the voltage between the harness connector of the inverter (rear) and the body ground.
+ - Voltage Inverter (rear) Connector Terminal B297 30 Body ground 9 – 16 V
Is the inspection result normal?
YES>>GO TO 8.
NO>>GO TO 5.
INSPECTION OF POWER SWITCH CIRCUIT 2
Power switch OFF.
Disconnect the IPDM E/R harness connector.
Check continuity between the IPDM E/R harness connector and inverter (rear) harness connector.
IPDM E/R Inverter (rear) Continuity Connector Terminal Connector Terminal E40 25 B297 30 Existed
Is the inspection result normal?
YES>>GO TO 6.
NO>>Repair or replace the malfunctioning parts.
INSPECTION OF POWER SWITCH CIRCUIT 3
Check continuity between the IPDM E/R harness connector and body ground.
| IPDM E/R | − | Continuity | |
|---|---|---|---|
| Connector | Terminal | ||
| E40 | 25 | Body ground | Not existed |
Is the inspection result normal?
YES>>GO TO 7.
NO>>Repair or replace the malfunctioning parts.
INSPECTION OF POWER SWITCH CIRCUIT 4
Inspect the following items:
Disconnection or short circuit in the wiring harness between the power switch and IPDM E/R
5A fuse (#144)
Repair or replace the malfunctioning parts.
PERFORM THE DTC CONFIRMATION PROCEDURE
Connect the disconnected harness connector of the inverter (rear).
Perform the DTC CONFIRMATION PROCEDURE. Refer to Confirmation Procedure.
Is "P030A-62" detected?
YES>>Replace the inverter (rear). Refer to Removal and Installation.
NO>>INSPECTION END
P0a1c-01 Drive Motor B Control Module Nissan Ariya 1st generation
DTC Description
DTC DETECTION LOGIC
| DTC | CONSULT screen terms | DTC detection condition | ||
|---|---|---|---|---|
| P0A1C | 01 | Drive Motor B Control Module | Diagnosis condition | At inverter (rear) start |
| Signal | ― | |||
| Threshold | An error was detected related to the controller inside the inverter (rear). | |||
| Diagnosis delay time | Within 1 second | |||
POSSIBLE CAUSE
Inverter (rear)
FAIL-SAFE
Control of the rear traction motor stops. Or, the vehicle cannot be started (READY status cannot be achieved).
Confirmation Procedure
PREPARATION BEFORE OPERATION
If another "Confirmation Procedure" was performed immediately before this task, always power switch OFF exit the Nissan Ariya vehicle and close all doors (including the back door), and wait for at least 60 seconds until the combination meter turns off before starting the next test.
>>GO TO 2.
PERFORM THE DTC CONFIRMATION PROCEDURE
With CONSULT
Power switch ON and wait at least 10 seconds.
Check the DTC.
Is "P0A1C-01" detected?
YES>>Refer to DTC Diagnosis Procedure.
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
REPLACEMENT OF THE INVERTER (REAR)
Replace the inverter (rear). Refer to Removal and Installation.
>>END
P0a1c-05 Drive Motor B Control Module Nissan Ariya 2026
DTC Description
DTC DETECTION LOGIC
| DTC | CONSULT screen terms | DTC detection condition | ||
|---|---|---|---|---|
| P0A1C | 05 | Drive Motor B Control Module | Diagnosis condition | READY state |
| Signal | — | |||
| Threshold | An error was detected related to the controller inside the inverter (rear). | |||
| Diagnosis delay time | Within 1 second | |||
POSSIBLE CAUSE
Inverter (rear)
FAIL-SAFE
Control of the rear traction motor stops. Or, the vehicle cannot be started (READY status cannot be achieved).
Confirmation Procedure
PREPARATION BEFORE OPERATION
If another "Confirmation Procedure" was performed immediately before this task, always power switch OFF exit the Nissan Ariya vehicle and close all doors (including the back door), and wait for at least 60 seconds until the combination meter turns off before starting the next test.
>>GO TO 2.
PERFORM THE DTC CONFIRMATION PROCEDURE
With CONSULT
Set the Nissan Ariya vehicle to READY and wait for at least 10 seconds.
Check the DTC.
Is "P0A1C-05" detected?
YES>>Refer to DTC Diagnosis Procedure.
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK FOR DTC RELATED TO THE HIGH VOLTAGE SYSTEM
With CONSULT
Power switch ON and wait at least 10 seconds.
Check the DTCs related to the high voltage system.
Is a DTC related to the high voltage system other than the inverter (rear) detected?
YES>>Check the detected DTC.
NO>>GO TO 2.
INSPECTION OF THE CAN COMMUNICATION CIRCUIT
Inspect the CAN communication circuit. Refer to Trouble Diagnosis Flow Chart.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair or replace the malfunctioning parts.
REPLACEMENT OF THE INVERTER (REAR)
Replace the inverter (rear). Refer to Removal and Installation.
>>END
P0a30-11 Drive Motor B Temperature Sensor Nissan Ariya: FE0
DTC Description
DTC DETECTION LOGIC
| DTC | CONSULT screen terms | DTC detection condition | ||
|---|---|---|---|---|
| P0A30 | 11 | Drive Motor B Temperature Sensor | Diagnosis condition | READY state |
| Signal | Temperature sensor signal of rear traction motor | |||
| Threshold | Disconnection or short circuit in the rear traction motor temperature sensor circuit | |||
| Diagnosis delay time | Within 1 second | |||
POSSIBLE CAUSE
Wiring harness or connector (Disconnection or short circuit in the rear traction motor temperature sensor circuit)
Rear traction motor (rear traction motor temperature sensor)
Inverter (rear)
FAIL-SAFE
Send rear traction motor temperature of 180 °C to the VCM.
Confirmation Procedure
PREPARATION BEFORE OPERATION
If another "Confirmation Procedure" was performed immediately before this task, always power switch OFF exit the Nissan Ariya vehicle and close all doors (including the back door), and wait for at least 60 seconds until the combination meter turns off before starting the next test.
>>GO TO 2.
PERFORM THE DTC CONFIRMATION PROCEDURE
With CONSULT
Set the Nissan Ariya vehicle to READY and wait for at least 10 seconds.
Check the DTC.
Is "P0A30-11" detected?
YES>>Refer to DTC Diagnosis Procedure.
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
INSPECTION OF THE TEMPERATURE SENSOR CIRCUIT OF THE REAR TRACTION MOTOR
Inspect the temperature sensor circuit of the rear traction motor. Refer to Diagnosis Procedure.
>>INSPECTION END
P0a30-4b Drive Motor B Temperature Sensor Nissan Ariya first Gen
DTC Description
DTC DETECTION LOGIC
| DTC | CONSULT screen terms | DTC detection condition | ||
|---|---|---|---|---|
| P0A30 | 4B | Drive Motor B Temperature Sensor | Diagnosis condition | READY state |
| Signal | — | |||
| Threshold | Overheat error was detected at the rear traction motor (stator). | |||
| Diagnosis delay time | Within 1 second | |||
POSSIBLE CAUSE
Oil coolant system for rear traction motor
Leakage of rear traction motor oil
Wiring harness or connector (Disconnection or short circuit in the rear traction motor temperature sensor circuit)
Rear traction motor (rear traction motor temperature sensor)
Inverter (rear)
FAIL-SAFE
The driving torque of the rear traction motor is limited to 0 N·m.
Confirmation Procedure
PREPARATION BEFORE OPERATION
If another "Confirmation Procedure" was performed immediately before this task, always power switch OFF exit the Nissan Ariya vehicle and close all doors (including the back door), and wait for at least 60 seconds until the combination meter turns off before starting the next test.
>>GO TO 2.
PERFORM THE DTC CONFIRMATION PROCEDURE
With CONSULT
Set the Nissan Ariya vehicle to READY and wait for at least 10 seconds.
Drive the vehicle for at least 20 minutes to warm it up.
Fully depress the accelerator pedal and accelerate the Nissan Ariya vehicle from 0 km/h to 10 km/h. Repeat this for 10 times without interruption to the maximum extent possible.
Stop the Nissan Ariya vehicle
Check the DTC.
Is "P0A30-4B" detected?
YES>>Refer to DTC Diagnosis Procedure.
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK FOR DTC RELATED TO THE HIGH VOLTAGE COOLING SYSTEM
With CONSULT
Power ON and wait at least 10 seconds.
Check "Self Diagnostic Result" of "EV/HEV".
Is a DTC related to the high voltage cooling system detected?
YES>>Check the detected DTC item. Refer to DTC Index.
NO>>GO TO 2.
INSPECTION OF COOLANT
Inspect the coolant level and leakage of coolant. Refer to COOLANT : Inspection.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair or replace the malfunctioning parts.
INSPECTION OF THE COOLANT HOSE
Check for clogging or twisting of the hose of the oil coolant circuit for the rear traction motor.
Is the inspection result normal?
YES>>GO TO 4.
NO>>Repair or replace the malfunctioning parts.
INSPECTION FOR REAR TRACTION MOTOR OIL
Check visually for leakage of the rear traction motor oil.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Replace the rear traction motor. Refer to Removal and Installation.
INSPECTION OF THE TEMPERATURE SENSOR CIRCUIT OF THE REAR TRACTION MOTOR
Inspect the temperature sensor circuit of the rear traction motor. Refer to Diagnosis Procedure.
>>INSPECTION END
P0a45-04 Drive Motor B Position Sensor Nissan Ariya first Gen
DTC Description
If a DTC remains in the past malfunctions, check the history of 12V battery removal and installation.
DTC DETECTION LOGIC
| DTC | CONSULT screen terms | DTC detection condition | ||
|---|---|---|---|---|
| P0A45 | 04 | Drive Motor B Position Sensor | Diagnosis condition | At inverter (rear) start or READY state |
| Signal | Rear traction motor resolver signal | |||
| Threshold | An error was detected at the rear traction motor resolver system. | |||
| Diagnosis delay time | Within 1 second | |||
POSSIBLE CAUSE
Wiring harness or connector (disconnection or short circuit in the resolver circuit of the rear traction motor)
Rear traction motor (traction motor resolver)
Inverter (rear)
FAIL-SAFE
Control of the rear traction motor stops. Or, the vehicle cannot be started (READY status cannot be achieved).
Confirmation Procedure
PREPARATION BEFORE OPERATION
If another "Confirmation Procedure" was performed immediately before this task, always power switch OFF exit the Nissan Ariya vehicle and close all doors (including the back door), and wait for at least 60 seconds until the combination meter turns off before starting the next test.
>>GO TO 2.
PERFORM THE DTC CONFIRMATION PROCEDURE
With CONSULT
Power switch ON and wait at least 10 seconds.
Check the DTC.
Is "P0A45-04" detected?
YES>>Refer to DTC Diagnosis Procedure.
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
INSPECTION OF THE REAR TRACTION MOTOR RESOLVER CIRCUIT
Inspect the rear traction motor resolver circuit. Refer to Component Inspection.
>>INSPECTION END
P0a79-62 Drive Motor B Inverter Nissan Ariya
DTC Description
DTC DETECTION LOGIC
| DTC | CONSULT screen terms | DTC detection condition | ||
|---|---|---|---|---|
| P0A79 | 62 | Drive Motor B Inverter | Diagnosis condition | READY state |
| Signal | — | |||
| Threshold | There was an inconsistency between the voltage value detected by the voltage monitor circuit and the system main relay ON/OFF that is received via CAN. | |||
| Diagnosis delay time | Within 2 seconds | |||
POSSIBLE CAUSE
CAN signal (system main relay ON/OFF signal)
System main relay
Voltage monitor circuit in the inverter (rear)
FAIL-SAFE
Control of the rear traction motor stops. Or, no limitation
Confirmation Procedure
PREPARATION BEFORE OPERATION
If another "Confirmation Procedure" was performed immediately before this task, always power switch OFF exit the Nissan Ariya vehicle and close all doors (including the back door), and wait for at least 60 seconds until the combination meter turns off before starting the next test.
>>GO TO 2.
PERFORM THE DTC CONFIRMATION PROCEDURE
With CONSULT
Set to READY and wait for at least 10 seconds.
Check the DTC.
Is "P0A79-62" detected?
YES>>Refer to DTC Diagnosis Procedure.
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
INSPECTION OF THE CAN COMMUNICATION CIRCUIT
Inspect the CAN communication circuit. Refer to Trouble Diagnosis Flow Chart.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace the malfunctioning parts.
CHECK FOR DTC RELATED TO THE HIGH VOLTAGE SYSTEM
With CONSULT
Power switch ON and wait at least 10 seconds.
Check the DTCs related to the high voltage system.
Is a DTC related to the high voltage system other than the inverter (rear) detected?
YES>>Check the detected DTC.
NO>>GO TO 3.
PRECONDITIONING
Disconnect high voltage circuit. Refer to HOW TO DISCONNECT HIGH VOLTAGE : Precautions.
Check voltage in high voltage circuit. Refer to CHECK VOLTAGE IN HIGH VOLTAGE CIRCUIT : Precautions.
GO TO 4.
INSPECTION OF THE HIGH VOLTAGE HARNESS
Inspect the high voltage harness between the Li-ion battery and the inverter (rear).
Is the inspection result normal?
YES>>GO TO 5.
NO>>Repair or replace the malfunctioning parts.
INSPECTION OF THE SYSTEM MAIN RELAY CIRCUIT
Inspect the circuits of system main relays 1 and 2.
66kWh Li-ion battery models
System main relay 1: Refer to Diagnosis Procedure.
System main relay 2: Refer to Diagnosis Procedure.
91kWh Li-ion battery models
System main relay 1: Refer to Diagnosis Procedure.
System main relay 2: Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>Replace the inverter (rear). Refer to Removal and Installation.
NO>>Repair or replace the malfunctioning parts.
P0a8b-A2 14 Volt Power Module System Voltage Nissan Ariya
DTC Description
If a DTC remains in the past malfunctions, check the history of 12V battery removal and installation.
DTC DETECTION LOGIC
| DTC | CONSULT screen terms | DTC detection condition | ||
|---|---|---|---|---|
| P0A8B | A2 | 14 Volt Power Module System Voltage | Diagnosis condition | At inverter (rear) start (power switch ON, READY state, or auto ACC ON state) |
| Signal | — | |||
| Threshold | Voltage supplied to the inverter (rear) by the 12V battery dropped below 9 V. | |||
| Diagnosis delay time | Within 1 second | |||
POSSIBLE CAUSE
12V battery voltage drop
Wiring harness or connector (disconnection or short circuit of 12V battery voltage supply circuit)
Inverter (rear)
FAIL-SAFE
Control of the rear traction motor stops.
Confirmation Procedure
PREPARATION BEFORE OPERATION
If another "Confirmation Procedure" was performed immediately before this task, always power switch OFF exit the Nissan Ariya vehicle and close all doors (including the back door), and wait for at least 60 seconds until the combination meter turns off before starting the next test.
>>GO TO 2.
PERFORM THE DTC CONFIRMATION PROCEDURE
With CONSULT
Power switch ON and wait at least 10 seconds.
Check the DTC.
Is "P0A8B-A2" detected?
YES>>Refer to DTC Diagnosis Procedure.
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
INSPECTION OF THE 12V BATTERY
Inspect the 12V battery. Refer to Work Flow.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace the malfunctioning parts.
INSPECTION OF THE HARNESS CONNECTOR
Power switch OFF.
Check mating conditions of the harness connector for the inverter (rear).
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair or replace the malfunctioning parts.
INSPECTION OF THE CONNECTOR TERMINAL
Disconnect the harness connector of the inverter (rear).
Check the inverter (rear) connector for water intrusion, or damage or corrosion of the terminals.
Is the inspection result normal?
YES>>GO TO 4.
NO>>Repair or replace the malfunctioning parts.
INSPECTION OF THE 12V BATTERY POWER SUPPLY CIRCUIT
Power switch ON.
Check the voltage between the harness connector terminals of the inverter (rear).
| Inverter (rear) | Voltage | ||
|---|---|---|---|
| Connector | Terminal | ||
| B297 | 18 | 4 | 9 – 16 V |
| 28 | 14 | ||
Is the inspection result normal?
YES>>Replace the inverter (rear). Refer to Removal and Installation.
NO>>GO TO 5.
INSPECTION OF THE GROUND CIRCUIT FOR THE INVERTER (REAR)
Check continuity between the harness connector of the inverter (rear) and the body ground.
| Inverter (rear) | − | Continuity | |
|---|---|---|---|
| Connector | Terminal | ||
| B297 | 4 | Body ground | Exsited |
| 14 | |||
Is the inspection result normal?
YES>>GO TO 6.
NO>>Repair or replace the malfunctioning parts.
INSPECTION OF 12V BATTERY POWER SUPPLY CIRCUIT 2
Inspect the following items:
Disconnection or short circuit in the wiring harness between harness connector terminals No. 18 and No. 28 between the 12V battery and the inverter (rear).
10A fuse (#93)
Repair or replace the malfunctioning parts.
P0af2-4b Drive Motor Inverter Temperature Sensor B Nissan Ariya SUV
DTC Description
DTC DETECTION LOGIC
| DTC | CONSULT screen terms | DTC detection condition | ||
|---|---|---|---|---|
| P0AF2 | 4B | Drive Motor Inverter Temperature Sensor B | Diagnosis condition | At inverter (rear) start or READY state |
| Signal | — | |||
| Threshold | Any of the following was detected.
|
|||
| Diagnosis delay time | Within 1 second | |||
POSSIBLE CAUSE
Coolant system for inverter (rear)
Inverter (rear)
FAIL-SAFE
The driving torque of the rear traction motor is limited to 0 N·m. Or, control of the rear traction motor stops.
Confirmation Procedure
PREPARATION BEFORE OPERATION
If another "Confirmation Procedure" was performed immediately before this task, always power switch OFF exit the Nissan Ariya vehicle and close all doors (including the back door), and wait for at least 60 seconds until the combination meter turns off before starting the next test.
>>GO TO 2.
PERFORM THE DTC CONFIRMATION PROCEDURE
With CONSULT
Set the Nissan Ariya vehicle to READY and wait for at least 10 seconds.
Drive the vehicle for at least 20 minutes to warm it up.
Fully depress the accelerator pedal and accelerate the Nissan Ariya vehicle from 0 km/h to 10 km/h. Repeat this for 10 times without interruption to the maximum extent possible.
Stop the Nissan Ariya vehicle.
Check the DTC.
Is "P0AF2-4B" detected?
YES>>Refer to DTC Diagnosis Procedure.
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK FOR DTC RELATED TO THE HIGH VOLTAGE COOLING SYSTEM
With CONSULT
Power switch ON and wait at least 10 seconds.
Check "Self Diagnostic Result" of "EV/HEV".
Is a DTC related to the hgih voltage cooling system detected?
YES>>Check the detected DTC item. Refer to DTC Index.
NO>>GO TO 2.
INSPECTION OF COOLANT
Inspect the coolant volume and leakage of coolant. Refer to COOLANT : Inspection.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair or replace the malfunctioning parts.
INSPECTION OF THE COOLANT HOSE
Check for clogging or twisting of the hose in the coolant system for the inverter (rear).
Is the inspection result normal?
YES>>GO TO 4.
NO>>Repair or replace the malfunctioning parts.
PERFORM THE DTC CONFIRMATION PROCEDURE
Perform the DTC CONFIRMATION PROCEDURE. Refer to Confirmation Procedure.
YES>>Replace the inverter (rear). Refer to Removal and Installation.
NO>>INSPECTION END
P2d3b-92 Hybrid/ev Discharge System Nissan Ariya 2023
DTC Description
DTC DETECTION LOGIC
| DTC | CONSULT screen terms | DTC detection condition | ||
|---|---|---|---|---|
| P2D3B | 92 | Hybrid/EV Discharge System | Diagnosis condition | At shutdown (after high voltage relay opens) |
| Signal | — | |||
| Threshold | A discharge error was detected at the smoothing capacitor. |
|||
| Diagnosis delay time | Within 3 seconds | |||
POSSIBLE CAUSE
Inverter (rear)
System main relay
FAIL-SAFE
—
Confirmation Procedure
PREPARATION BEFORE OPERATION
If another "Confirmation Procedure" was performed immediately before this task, always power switch OFF exit the Nissan Ariya vehicle and close all doors (including the back door), and wait for at least 60 seconds until the combination meter turns off before starting the next test.
>>GO TO 2.
PERFORM THE DTC CONFIRMATION PROCEDURE
With CONSULT
Set the Nissan Ariya vehicle to READY and wait for at least 10 seconds.
Check the DTC.
Is "P2D3B-92" detected?
YES>>Refer to DTC Diagnosis Procedure.
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
DTC CHECK (REAR MOTOR CONTROL)
With CONSULT
Set the Nissan Ariya vehicle to READY and wait for at least 10 seconds.
Check "Self Diagnostic Result" under "REAR MOTOR CONTROL".
Is a DTC P2D3B-92 detected at the same time as another DTC?
YES>>Check the DTC Inspection Priority Chart, and perform diagnosis for the DTC with the higher inspection priority. Refer to DTC Inspection Priority Chart.
NO>>GO TO 2.
CHECK FOR DTC RELATED TO THE HIGH VOLTAGE SYSTEM
With CONSULT
Check the DTCs related to the high voltage system.
Is a DTC related to the high voltage system other than the inverter (rear) detected?
YES>>Check the detected DTC.
NO>>Replace the inverter (rear). Refer to Removal and Installation.
P3081-44 Resolver Offset Value Error Nissan Ariya SUV
DTC Description
DTC DETECTION LOGIC
| DTC | CONSULT screen terms | DTC detection condition | ||
|---|---|---|---|---|
| P3081 | 44 | Resolver Offset Value Error | Diagnosis condition | At inverter (rear) start |
| Signal | — | |||
| Threshold | Any of the following was detected.
|
|||
| Diagnosis delay time | Within 1 second | |||
POSSIBLE CAUSE
Inverter (rear)
Resolver offset value was not written or there was an error in the work.
FAIL-SAFE
Change the resolver offset value to the default value. This reduces torque because optimal control of the rotor position is not possible.
Confirmation Procedure
PREPARATION BEFORE OPERATION
If another "Confirmation Procedure" was performed immediately before this task, always power switch OFF exit the Nissan Ariya vehicle and close all doors (including the back door), and wait for at least 60 seconds until the combination meter turns off before starting the next test.
>>GO TO 2.
PERFORM THE DTC CONFIRMATION PROCEDURE
With CONSULT
Power switch ON and wait at least 10 seconds.
Check the DTC.
Is "P3081-44" detected?
YES>>Refer to DTC Diagnosis Procedure.
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
WRITING THE RESOLVER OFFSET VALUE
Perform the work to write the resolver offset value. Refer to Description.
Perform the DTC CONFIRMATION PROCEDURE. Refer to Confirmation Procedure.
Is "P3081-44" detected?
YES>>Replace the inverter (rear). Refer to Removal and Installation.
NO>>INSPECTION END
P30e5-04 Drive Motor B Coolant Pump Nissan Ariya SUV
DTC Description
DTC DETECTION LOGIC
| DTC | CONSULT screen terms | DTC detection condition | ||
|---|---|---|---|---|
| P30E5 | 04 | Drive Motor B Coolant Pump Control | Diagnosis condition | READY state |
| Signal | Rear traction motor oil pump signal | |||
| Threshold | Error notification signal was received from the oil pump of the rear traction motor. | |||
| Diagnosis delay time | Within 10 seconds | |||
POSSIBLE CAUSE
Wiring harness or connector
(Disconnection or short circuit in the oil temperature sensor of the rear traction motor)
(Disconnection or short circuit in the oil pump of the rear traction motor)
Rear traction motor
(Oil temperature sensor of the rear traction motor)
(Oil pump of the rear traction motor)
Inverter (rear)
FAIL-SAFE
The driving torque of the rear traction motor is limited to 30%.
Confirmation Procedure
PREPARATION BEFORE OPERATION
If another "Confirmation Procedure" was performed immediately before this task, always power switch OFF exit the Nissan Ariya vehicle and close all doors (including the back door), and wait for at least 60 seconds until the combination meter turns off before starting the next test.
>>GO TO 2.
PERFORM THE DTC CONFIRMATION PROCEDURE
With CONSULT
Set the Nissan Ariya vehicle to READY and wait for at least 10 seconds.
Check the DTC.
Is "P30E5-04" detected?
YES>>Refer to DTC Diagnosis Procedure.
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK FOR DTC RELATED TO THE REAR TRACTION MOTOR OIL TEMPERATURE SENSOR
With CONSULT
Power switch ON.
Check "Self Diagnostic Result" of "REAR MOTOR CONTROL".
Is a DTC related to the rear traction motor oil temperature sensor detected?
YES>>Inspect the oil temperature sensor circuit of the rear traction motor. Refer to Diagnosis Procedure.
NO>>GO TO 2.
INSPECTION OF THE OIL PUMP CIRCUIT OF THE REAR TRACTION MOTOR
Inspect the oil pump circuit of the rear traction motor. Refer to Diagnosis Procedure.
>>INSPECTION END
P30e6-11 Drive Motor B Excitation Current Nissan Ariya first Gen
DTC Description
DTC DETECTION LOGIC
| DTC | CONSULT screen terms | DTC detection condition | ||
|---|---|---|---|---|
| P30E6 | 11 | Drive Motor B Excitation Current | Diagnosis condition | READY state |
| Signal | — | |||
| Threshold | An excitation module error was detected. | |||
| Diagnosis delay time | Within 1 second | |||
POSSIBLE CAUSE
Inverter (rear)
FAIL-SAFE
Control of the rear traction motor stops
Confirmation Procedure
PREPARATION BEFORE OPERATION
If another "Confirmation Procedure" was performed immediately before this task, always power switch OFF exit the Nissan Ariya vehicle and close all doors (including the back door), and wait for at least 60 seconds until the combination meter turns off before starting the next test.
>>GO TO 2.
PERFORM THE DTC CONFIRMATION PROCEDURE
With CONSULT
Set the Nissan Ariya vehicle to READY and wait for at least 10 seconds.
Depress the accelerator pedal to increase the Nissan Ariya vehicle speed up to 10 km/h.
Stop the vehicle.
Check the DTC.
Is "P30E6-11" detected?
YES>>Refer to DTC Diagnosis Procedure.
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
INSPECTION OF THE EXCITATION CIRCUIT
Remove the inverter (rear) and rear traction motor from the Nissan Ariya vehicle. Refer to Removal and Installation.
Remove the excitation cover and inspect the connection conditions of the bus bar and excitation harness of the inverter (rear).

Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace the malfunctioning parts.
REPLACEMENT OF THE INVERTER (REAR)
Replace the inverter (rear). Refer to Removal and Installation.
>>END
P30e6-12 Drive Motor B Excitation Current Nissan Ariya SUV
DTC Description
If a DTC remains in the past malfunctions, check the history of 12V battery removal and installation.
DTC DETECTION LOGIC
| DTC | CONSULT screen terms | DTC detection condition | ||
|---|---|---|---|---|
| P30E6 | 12 | Drive Motor B Excitation Current | Diagnosis condition | READY state |
| Signal | — | |||
| Threshold | An excitation module error was detected. | |||
| Diagnosis delay time | Within 1 second | |||
POSSIBLE CAUSE
Rear traction motor
Inverter (rear)
FAIL-SAFE
Control of the rear traction motor stops
Confirmation Procedure
PREPARATION BEFORE OPERATION
If another "Confirmation Procedure" was performed immediately before this task, always power switch OFF exit the Nissan Ariya vehicle and close all doors (including the back door), and wait for at least 60 seconds until the combination meter turns off before starting the next test.
>>GO TO 2.
PERFORM THE DTC CONFIRMATION PROCEDURE
With CONSULT
Set the Nissan Ariya vehicle to READY and wait for at least 10 seconds.
Depress the accelerator pedal to increase the Nissan Ariya vehicle speed up to 10 km/h.
Drive the vehicle for approximately 5 minutes.
Stop the Nissan Ariya vehicle.
Check the DTC.
Is "P30E6-12" detected?
YES>>Refer to DTC Diagnosis Procedure.
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
INSPECTION OF SHORT CIRCUIT CONDITION FOR REAR TRACTION MOTOR ROTOR COIL
Remove the inverter (rear) and rear traction motor from the Nissan Ariya vehicle. Refer to Removal and Installation.
Remove the excitation cover then disconnect excitation harness from bus bar of the inverter (rear).

Check the rotor coil resistance value at the rear traction motor and check for short circuits.

Rear traction motor Resistance value in short circuit condition Terminal Ex+ Ex- 4.55 Ω or less
Is the resistance value 4.55 Ω or less?
YES>>The rotor coil has malfunctioned (short circuit condition). Replace the rear traction motor. Refer to Removal and Installation.
NO>>GO TO 2.
REPLACEMENT OF THE INVERTER (REAR)
Replace the inverter (rear). Refer to Removal and Installation.
>>END
P30e7-01 Drive Motor B Excitation Current Sensor Nissan Ariya first Gen
DTC Description
DTC DETECTION LOGIC
| DTC | CONSULT screen terms | DTC detection condition | ||
|---|---|---|---|---|
| P30E7 | 01 | Drive Motor B Excitation Current Sensor | Diagnosis condition | READY state |
| Signal | — | |||
| Threshold | Excitation module current is not flowing normally. | |||
| Diagnosis delay time | Within 1 second | |||
POSSIBLE CAUSE
Inverter (rear)
Rear traction motor
FAIL-SAFE
Control of the rear traction motor stops.
Confirmation Procedure
PREPARATION BEFORE OPERATION
If another "Confirmation Procedure" was performed immediately before this task, always power switch OFF exit the Nissan Ariya vehicle and close all doors (including the back door), and wait for at least 60 seconds until the combination meter turns off before starting the next test.
>>GO TO 2.
PERFORM THE DTC CONFIRMATION PROCEDURE
With CONSULT
Set the Nissan Ariya vehicle to READY and wait for at least 10 seconds.
Increase the vehicle speed to 10 km/h.
Stop the Nissan Ariya vehicle.
Check the DTC.
Is "P30E7-01" detected?
YES>>Refer to DTC Diagnosis Procedure.
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
DTC CHECK (REAR MOTOR CONTROL)
With CONSULT
Set the Nissan Ariya vehicle to READY and wait for at least 10 seconds.
Check "Self Diagnostic Result" under "REAR MOTOR CONTROL".
Is a DTC P30E7-01 detected at the same time as another DTC?
YES>>Check the DTC Inspection Priority Chart, and perform diagnosis for the DTC with the higher inspection priority. Refer to DTC Inspection Priority Chart.
NO>>GO TO 2.
INSPECTION OF THE EXCITATION CIRCUIT
Remove the inverter (rear) and rear traction motor from the Nissan Ariya vehicle. Refer to Removal and Installation.
Remove the excitation cover and inspect the connection conditions of the bus bar and excitation harness of the inverter (rear).

Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair or replace the malfunctioning parts.
CHECK OF THE ROTOR COIL RESISTANCE VALUE AT THE REAR TRACTION MOTOR
Check the rotor coil resistance value at the rear traction motor. Refer to Component Inspection.
Is the inspection result normal?
YES>>Replace the inverter (rear). Refer to Removal and Installation.
NO>>Replace the rear traction motor. Refer to Removal and Installation.
U2143-82 Can Comm Circuit Nissan Ariya SUV
DTC Description
DTC DETECTION LOGIC
| DTC | CONSULT screen terms | DTC detection condition | ||
|---|---|---|---|---|
| U2143 | 82 | CAN communication error (VCM/HCM) | Diagnosis condition | READY state |
| Signal | EV system CAN communication signal | |||
| Threshold | Any of the following was detected.
|
|||
| Diagnosis delay time | Within 10 seconds | |||
POSSIBLE CAUSE
Inverter (rear)
VCM
CAN communications line [between inverter (rear) and VCM]
FAIL-SAFE
Vehicle stops (torque 0 N·m), or the driving torque of the rear traction motor is limited, or is not limited.
Confirmation Procedure
PREPARATION BEFORE OPERATION
If another "Confirmation Procedure" was performed immediately before this task, always power switch OFF exit the Nissan Ariya vehicle and close all doors (including the back door), and wait for at least 60 seconds until the combination meter turns off before starting the next test.
>>GO TO 2.
PERFORM THE DTC CONFIRMATION PROCEDURE
With CONSULT
Set the Nissan Ariya vehicle to READY and wait for at least 10 seconds.
Check the DTC.
Is "U2143-82" detected?
YES>>Refer to DTC Diagnosis Procedure.
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
Perform diagnosis of the CAN communication system. Refer to Trouble Diagnosis Flow Chart.