Certification Ecu
- Removal
- Installation
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during certification ECU (smart key ECU assembly) removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/ReplacedReplaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
Certification ECU (smart key ECU assembly) |
Code registration |
|
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.
Click here ![]()
HINT:
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
- Items for which learning is completed by driving the Toyota Prius vehicle
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
Front Camera System
Drive the Toyota Prius vehicle straight ahead at 35 km/h or more for 5 second or more.

- Items for which learning is completed by operating the vehicle normally
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
*1: w/o Power Back Door System *2: w/ Power Back Door System
Power Door Lock Control System*1
- Back door opener
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.

Power Back Door System*2
Reset back door close position

Air Conditioning System
for HEV Model: - After the ignition switch is turned to ON, the servo motor standard position is recognized.
- After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized.
-

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
PRECAUTION |
- |
- |
- |
|
2 |
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
- |
- |
- |
- |
3 |
JUNCTION BLOCK BRACKET |
82673A |
- |
- |
|
4 |
CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
89990A |
- |
- |
|
PROCEDURE
1. PRECAUTION
![]() |
NOTICE: After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Click here |
2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
(a) for M20A-FXS:
Click here ![]()
(b) for 2ZR-FXE:
Click here ![]()
3. REMOVE JUNCTION BLOCK BRACKET
![]() |
Click here |
4. REMOVE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
![]() |
NOTICE:
|

Installation
INSTALLATION
COMPONENTS (INSTALLATION)
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
89990A |
- |
- |
|
2 |
JUNCTION BLOCK BRACKET |
82673A |
- |
- |
|
3 |
CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL |
- |
- |
- |
- |
4 |
PERFORM CODE REGISTRATION |
- |
- |
- |
|
5 |
INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL |
- |
- |
- |
|
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
- |
- |
PROCEDURE
1. INSTALL CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
![]() |
NOTICE:
|
2. INSTALL JUNCTION BLOCK BRACKET
![]() |
Click here |
Torque:
8 N·m {82 kgf·cm, 71 in·lbf}
3. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
(a) for M20A-FXS:
Click here ![]()
(b) for 2ZR-FXE:
Click here ![]()
4. PERFORM CODE REGISTRATION
Click here ![]()
5. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL
HINT:
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click here
![]()



















