Wiper And Washer System

In this manual: Wiper And Washer System
How To Troubleshoot Ecu Controlled Systems — 1How To Use This Manual — 1Identification Information — 1Repair Instruction — 1Terms — 12zr-fxe Air Cleaner Filter Element — 12zr-fxe Auxiliary Battery — 12zr-fxe Coolant (for Engine Coolant) — 12zr-fxe Oil And Oil Filter — 12zr-fxe Spark Plug — 1Air Conditioning Filter — 1Battery Cooling Filter — 1Brake Fluid — 1Coolant (for Inverter) — 1Front Brake Flexible Hose — 1Front Disc Brake Pad — 1Front Lower Ball Joint — 1Front Wheel Alignment — 1Front Wiper Rubber — 1General Maintenance — 1M20a-fxs Air Cleaner Filter Element — 1M20a-fxs Auxiliary Battery — 1M20a-fxs Coolant (for Engine Coolant) — 1M20a-fxs Oil And Oil Filter — 1M20a-fxs Spark Plug — 1Pa10/pb10/pb12 Hybrid Transaxle Fluid — 1Q810 Hybrid Transaxle Fluid — 1Rear Brake Flexible Hose — 1Rear Disc Brake Pad — 1Rear Wheel Alignment — 1Steering Column — 1Tire And Wheel — 1Transmitter Battery — 1When Disconnecting Or Reconnecting Battery Terminal — 1When Replacing Or Removing/installing Parts — 1Automatic High Beam Main Switch — 1Automatic High Beam System — 1Driver Monitor Camera — 1Driver Monitor Camera System — 1Driver Monitor Ecu — 1Front Camera — 1Front Camera System — 1Front Radar Sensor System — 1Front Side Radar Sensor — 1Front Side Radar Sensor System — 1Millimeter Wave Radar Sensor — 1Utility — 1Advanced Park — 1Advanced Park Main Switch — 1Amplifier Antenna — 1Audio And Visual System — 1Front Door Speaker — 1Instrument Panel Speaker — 1Microphone — 1Noise Filter — 1Pillar Speaker — 1Radio Antenna Cord (for Back Door) — 1Radio Antenna Cord (for Instrument Panel) — 1Radio Antenna Cord (for Roof) — 1Radio Receiver — 1Rear Door Speaker — 1Roof Antenna — 1Stereo Component Amplifier — 1Stereo Jack Adapter Assembly — 1Window Glass Antenna Wire — 1Back-up Battery — 1Dcm(telematics Transceiver) — 1Manual(sos)switch — 1Safety Connect System — 1Telephone And Gps Antenna (for Front Side) — 1Telephone And Gps Antenna (for Roof Side) — 1Telephone And Gps Antenna Cords — 1Garage Door Opener System (for Digital Inner Mirror) — 1Garage Door Opener System (for Ec Inner Mirror) — 1Blind Spot Monitor Sensor — 1Blind Spot Monitor System — 1Clearance Warning Ecu — 1Intuitive Parking Assist System — 1Panoramic View Monitor Switch — 1Panoramic View Monitor System — 1Parking Assist Ecu — 1Parking Assist Light — 1Parking Assist Monitor System — 1Parking Support Brake System — 1Rear View Monitor System — 1Television Camera (for Front) — 1Television Camera (for Rear) — 1Television Camera (for Side) — 1Ultrasonic Sensor (for Front) — 1Ultrasonic Sensor (for Rear) — 1Brake Actuator — 1Brake Pedal Stroke Sensor — 1Electronically Controlled Brake System — 1Front Speed Sensor — 1Rear Speed Sensor (for Awd) — 1Steering Angle Sensor — 1Brake Booster — 1Brake Fluid — 1Brake Line — 1Brake Pedal — 1Brake System — 1Electric Parking Brake Actuator — 1Electric Parking Brake Switch — 1Electric Parking Brake System — 1Forced Release — 1Front Axle Hub — 1Front Axle Hub Bolt — 1Rear Axle Carrier (for 2wd) — 1Rear Axle Carrier (for Awd) — 1Rear Axle Hub (for 2wd) — 1Rear Axle Hub (for Awd) — 1Rear Axle Hub Bolt — 1Steering Knuckle — 1Drive Shaft System — 1Front Drive Shaft Assembly — 1Rear Drive Shaft Assembly — 1Combination Switch — 1Electronic Shift Lever System — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Oil Seal — 1Hybrid Transaxle System — 1Input Shaft Oil Seal — 1Motor Cable — 1Pa10 Hybrid Vehicle Transaxle — 1Pa10 Manual Parking Lock Release — 1Pa10 Oil Cooler — 1Pb10/pb12 Hybrid Vehicle Transaxle — 1Pb10/pb12 Manual Parking Lock Release — 1Pb10/pb12 Oil Cooler — 1Shift Control Actuator — 1Shift Lever — 1Shift Lever Knob — 1Differential Side Gear Shaft — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Side Gear Oil Seal — 1Motor Cable — 1Rear Traction Motor — 1Coolant (for Engine) — 1Cooling Fan Motor — 1Cooling Fan System — 1Radiator — 1Relay — 1Thermostat — 1Water Pump — 1Canister — 1Egr Cooler — 1Egr Valve — 1Emission Control System — 1Fuel Tank Cap — 1Pcv Valve — 1Purge Valve — 1Vacuum Sensor — 1Air Fuel Ratio Sensor — 1Camshaft Oil Control Valve — 1Camshaft Position Sensor — 1Crankshaft Position Sensor — 1Ecm — 1Engine Coolant Temperature Sensor — 1Heated Oxygen Sensor — 1Ignition Coil And Spark Plug — 1Ignition System — 1Knock Sensor — 1Mass Air Flow Meter — 1Relay — 1Sfi System — 1Throttle Body — 1Camshaft — 1Cylinder Block — 1Cylinder Head — 1Cylinder Head Gasket — 1Engine — 1Engine Assembly — 1Engine Unit — 1Front Crankshaft Oil Seal — 1Rear Crankshaft Oil Seal — 1Fuel Filter — 1Fuel Injector — 1Fuel Pressure Regulator — 1Fuel Pump — 1Fuel Sender Gauge Assembly — 1Fuel System — 1Fuel Tank — 1Air Cleaner Filter Element — 1Exhaust Manifold — 1Exhaust Pipe — 1Intake Manifold — 1Intake System — 1Lubrication System — 1Oil And Oil Filter — 1Oil Pan And Oil Level Sensor — 1Oil Pressure Switch — 1Oil Pump — 1Accelerator Pedal Sensor — 1Battery Blower (for Hev Model) — 1Battery Ecu (for Hev Model) — 1Battery Ecu (for Phev Model) — 1Battery Voltage Sensor (for Phev Model) — 1Charge Cable (for Phev Model) — 1Charge Indicator (for Phev Model) — 1Charge Inlet (for Phev Model) — 1Combination Switch — 1Coolant (for Inverter) — 1Cooler (for Phev Model) — 1Electric Vehicle Charger Assembly (for Phev Model) — 1Frame Wire (for Hev Model) — 1Frame Wire (for Phev Model) — 1Heater Relay (for Phev Model) — 1Hv Battery (for Hev Model) — 1Hv Battery (for Phev Model) — 1Hv Battery Heater (for Phev Model) — 1Hv Battery Stack (for Phev Model) — 1Hv Relay Assembly (for Hev Model) — 1Hv Relay Assembly (for Phev Model) — 1Hybrid Battery System (for 2zr-fxe) — 1Hybrid Battery System (for M20a-fxs) — 1Hybrid Battery System (for Phev Model) — 1Hybrid Vehicle Control Ecu — 1Inverter With Converter (for Hev Model) — 1Motor Generator Control System (for 2zr-fxe) — 1Plug-in Charge Control System (for Phev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Service Plug Grip (for Hev Model) — 1Sub Radiator — 1Water Pump With Motor — 1Auxiliary Battery — 1Battery Current Sensor — 1Charging System — 1Solar Charging System — 1Solar Control Unit — 1Solar Roof — 1Can Communication System (for Hev Model) — 1Lin Communication System — 1Network Gateway Ecu — 1Integration Control Supply — 1Main Body Ecu — 1Power Integration System — 1Sub Battery System — 1Power Steering Ecu — 1Power Steering System — 1Heated Steering Wheel Controller — 1Heated Steering Wheel System — 1Steering Column Assembly — 1Steering Heater Switch — 1Steering Pad Switch — 1Steering System — 1Steering Wheel — 1Front Lower Ball Joint — 1Front Lower Suspension Arm (for 2zr-fxe Lh Side) — 1Front Lower Suspension Arm (for 2zr-fxe Rh Side) — 1Front Lower Suspension Arm (for M20a-fxs) — 1Front Shock Absorber — 1Front Stabilizer Bar — 1Front Suspension Member — 1Rear Coil Spring — 1Rear Lower Arm (for Awd Lh Side) — 1Rear Lower Arm (for Awd Rh Side) — 1Rear Lower Arm (for Hev Model 2wd) — 1Rear Lower Arm (for Phev Model) — 1Rear Shock Absorber — 1Rear Stabilizer Bar — 1Rear Suspension Member (for 2wd) — 1Rear Suspension Member (for Awd) — 1Rear Trailing Arm — 1Rear Upper Arm — 1Tire And Wheel System — 1Tire Repair Seal — 1Tire Pressure Warning Receiver — 1Tire Pressure Warning System — 1Tire Pressure Warning Valve — 1Acoustic Vehicle Alerting System — 1Vehicle Approaching Speaker — 1Vehicle Approaching Speaker Ecu — 1Back Door — 1Back Door Closer Ecu — 1Back Door Opener Switch — 1Back Door Support — 1Back Door Weatherstrip — 1Charge Lid Courtesy Switch — 1Charge Lid Opener Motor Assembly — 1Charge Lid Opener System — 1Charge Lid Opener Unit — 1Front Door — 1Front Door Opening Trim Weatherstrip — 1Fuel Lid Opener Motor Assembly — 1Fuel Lid Opener Switch — 1Fuel Lid Opener System — 1Hood — 1Hood Lock Control Cable Assembly — 1Power Back Door Closer Switch — 1Power Back Door Control Switch — 1Power Back Door Drive Unit — 1Power Back Door System — 1Power Back Door Touch Sensor — 1Power Back Door Warning Buzzer — 1Rear Door — 1Rear Door Opening Trim Weatherstrip — 1Reserve Lock Switch — 1Front Bumper — 1Front Door Belt Moulding — 1Front Door Window Frame Moulding — 1Front Fender — 1Front Pillar Upper Cover — 1Grille Shutter — 1Grille Shutter System — 1Name Plate — 1Quarter Garnish — 1Rear Bumper — 1Rear Door Belt Moulding — 1Rear Door Window Frame Moulding — 1Rear Wheel House Plate — 1Rocker Panel Moulding — 1Roof Drip Side Finish Moulding — 1Roof Garnish — 1Wheel Opening Moulding (for Front Side) — 1Wheel Opening Moulding (for Rear Side) — 1Windshield Outside Moulding — 1Horn — 1Horn System — 1Relay — 1Automatic Light Control Sensor — 1Back-up Light Assembly — 1Charge Lid Light — 1Front Marker Light — 1Hazard Warning Switch — 1Headlight Assembly — 1Headlight Dimmer Switch — 1Headlight Leveling Switch — 1High Mounted Stop Light Assembly — 1Illumination Light Assembly — 1License Plate Light Assembly — 1Lighting System — 1Rear Combination Light Assembly — 1Rear Light Assembly — 1Rear Side Marker Light Assembly — 1Relay — 1Side Turn Signal Light Assembly — 1Stop Light Switch — 1Switch Housing — 1Outer Mirror Switch — 1Outer Rear View Mirror — 1Outer Rear View Mirror Cover — 1Outer Rear View Mirror Glass — 1Power Mirror Control System — 1Back Door Glass — 1Front Passenger Side Power Window Switch — 1Power Window Control System — 1Power Window Master Switch — 1Power Window Regulator Motor (for Front Door) — 1Power Window Regulator Motor (for Rear Door) — 1Rear Power Window Switch — 1Relay — 1Roof Window Fix Glass — 1Window Defogger System — 1Windshield Deicer Switch — 1Windshield Deicer System — 1Windshield Glass — 1Front Wiper Motor — 1Rain Sensor — 1Relay — 1Washer Motor — 1Washer Nozzle (for Front Side) — 1Washer Nozzle (for Rear Television Camera) — 1Wiper And Washer System — 1Wiper Ecu — 1Wiper Switch — 1Back Door Lock — 1Door Control Receiver — 1Door Control Switch — 1Door Control Transmitter — 1Door Lock Release Motor (for Rear Side) — 1Door Outside Handle (for Rear Side) — 1Front Door Lock — 1Power Door Lock Control System — 1Rear Door Lock — 1Transmitter Battery — 1Wireless Door Lock Control System — 1Accumulator — 1Air Conditioning Amplifier — 1Air Conditioning Panel — 1Air Conditioning Pressure Sensor — 1Air Conditioning Unit — 1Ambient Temperature Sensor — 1Blower Unit — 1Condenser (for Hev Model) — 1Condenser (for Phev Model) — 1Discharge Temperature Sensor — 1Electric Expansion Valve (cooling) — 1Electric Expansion Valve (heating) — 1Evaporator Pipe Temperature Sensor — 1Evaporator Pressure Regulator — 1Front Blower Motor — 1Front Evaporator Front Solenoid Valve — 1Air Conditioning System (for Hev Model) — 1Front Evaporator Temperature Sensor — 1Heat Exchanger Temperature Sensor — 1Heat Pump Ecu — 1High Pressure Magnetic Valve — 1Humidity Sensor — 1Internal Condenser Temperature Sensor — 1Low Pressure Magnetic Valve — 1Refrigerant (for Hfc-134a(r134a)) — 1Refrigerant Line (for Hev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Room Temperature Sensor — 1Solar Sensor — 1Floor Carpet — 1Front Console Box — 1Instrument Panel Safety Pad — 1Roof Headlining — 1Roof Sunshade — 1Ambient Light (for Driver Side) — 1Ambient Light (for Front Passenger Side) — 1Back Door Courtesy Switch — 1Footwell Light — 1Glove Box Light — 1Lighting System — 1Luggage Compartment Room Light — 1Personal Light — 1Room Light — 1Vanity Light — 1Vanity Light Switch — 1Combination Meter — 1Meter / Gauge System — 1Trip Switch — 1Digital Inner Mirror — 1Digital Rear-view Mirror System — 1Inner Mirror Monitor Camera — 1Inner Rear View Mirror (w/o Ec Mirror) — 1Accessory Power Outlet System — 1Power Outlet Socket (for Console Box Front Side) — 1Power Outlet Socket (for Console Box Rear Side) — 1Power Outlet Socket (for Console Box) — 1Power Outlet Socket (for Luggage Compartment) — 1Power Outlet Switch — 1Wireless Charger Assembly — 1Wireless Charging System — 1Climate Control Seat System — 1Front Power Seat Control System (w/ Memory) — 1Front Power Seat Motor Assembly — 1Front Seat Assembly (for Power Seat) — 1Front Seat Cushion Heater (for Power Seat) — 1Front Seatback Heater (for Power Seat) — 1Lumbar Support Adjuster Assembly — 1Power Seat Control Ecu — 1Power Seat Switch — 1Power Seat Track Rail Assembly — 1Rear Seat Assembly — 1Rear Seat Cushion Heater — 1Rear Seat Reminder System — 1Rear Seatback Heater — 1Seat Heater Control — 1Seat Heater Switch (for Front Seat) — 1Seat Heater Switch (for Rear Side) — 1Seat Heater System — 1Seat Memory Switch — 1Child Restraint Seat Anchor Bracket — 1Front Seat Inner Belt Assembly — 1Front Seat Outer Belt Assembly — 1Occupant Detection Sensor (for Front Passenger Side) — 1Rear Center Seat Outer Belt Assembly — 1Rear Seat Inner Belt Assembly (for Rh Side) — 1Rear Seat Outer Belt Assembly — 1Seat Belt Warning System (w/ Occupant Classification System) — 1Tongue Plate Stopper — 1Airbag System — 1Center Airbag Sensor Assembly — 1Curtain Shield Airbag Assembly — 1Front Airbag Sensor — 1Front Passenger Airbag Assembly — 1Front Seat Side Airbag Assembly — 1Inspection After Collision — 1Knee Airbag Assembly — 1Occupant Classification System — 1Rear Seat Side Airbag Assembly — 1Side Airbag Sensor (for Center Pillar) — 1Side Airbag Sensor (for Front Door) — 1Spiral Cable — 1Steering Pad — 1Certification Ecu — 1Digital Key Ecu — 1Digital Key Receiver (for Front Floor) — 1Digital Key Receiver (for Outside Luggage Compartment) — 1Digital Key Receiver (for Rear Door) — 1Digital Key System — 1Electrical Key Oscillator (for Front Floor) — 1Electrical Key Oscillator (for Outside Luggage Compartment) — 1Electrical Key Oscillator (for Rear Floor) — 1Engine Hood Courtesy Switch — 1Id Code Box — 1Smart Key System (for Start Function) — 1
~51min read
  • Precaution
  • Parts Location
  • System Diagram
  • How To Proceed With Troubleshooting
  • Operation Check
  • Customize Parameters
  • Problem Symptoms Table
  • Terminals Of Ecu
  • Fail-safe Chart
  • Data List / Active Test
  • Humidity/Rain Sensor Missing Message (B127987)
  • Rain Sensor Component Internal Failure (B140096)
  • Wiper Module Missing Message (B235787)
  • Front Wiper Motor Circuit
  • Wiper and Washer Switch Circuit
  • Rear Cleaner Motor and Relay Circuit
  • Washer Fluid Level Warning Switch Circuit

Precaution

PRECAUTION

PRECAUTION FOR DISCONNECTING CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click here

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click here

PRECAUTION FOR WASHER NOZZLE ADJUSTMENT

(a) Do not clean or adjust the washer nozzle with a safety pin, etc. because:

(1) The washer nozzle tip is made of resin and may be damaged.

(2) Adjustment is not necessary for this spray type washer nozzle. If it is necessary to change the nozzle angle, replace the washer nozzle with one that has a different nozzle angle.

Click here

(b) If the washer nozzle is clogged with wax, etc., remove it and clean the nozzle hole with a soft resin brush or other cleaning tool.

PRECAUTIONS FOR RAIN SENSOR (w/ Auto Wiper System)

(a) When the ignition switch is ON and the front wiper switch is in the AUTO position, the rain sensor may operate the front wipers if the rain sensor sensing portion of the windshield glass is touched by a hand or if something moist, such as a wet cloth, is brought near. This may lead to injury or damage to the Toyota Prius vehicle.

(b) When the ignition switch is ON and the front wiper switch is in the AUTO position, the rain sensor may operate the wipers if the rain sensor or parts around the rain sensor (windshield glass, rain sensor cover, etc.) are vibrated.

(c) If the windshield glass is coated with a water-repellent coating, the rain sensor may not correctly detect the amount of raindrops that strike the windshield and the auto wiper system may not operate normally.

(d) As the rain sensor is an optical sensor, if sunlight intermittently strikes the windshield glass or the rain sensor sensing portion of the windshield glass is dirty, the auto wiper system may not operate normally.

(e) The rain sensor cannot operate if the front wipers are stopped in any position other than the park position.

PRECAUTIONS FOR REAR CAMERA WASHER SYSTEM (w/ Rear Camera Cleaner System)

(a) After replacing the parking assist ECU or rear television camera assembly, it is necessary to set the camera cleaner setting to ON.

  • Parking Assist Monitor System:

    Click here

  • Panoramic View Monitor System:

    Click here

Parts Location

PARTS LOCATION

ILLUSTRATION

*A

for LHD

*B

w/ Auto Wiper System

*C

w/ Level Warning Switch Assembly

-

-

*1

WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY

*2

WINDSHIELD WIPER MOTOR ASSEMBLY

*3

RAIN SENSOR

*4

NO. 1 ENGINE ROOM RELAY BLOCK AND NO. 1 JUNCTION BLOCK ASSEMBLY

- WINDSHILD WIPER RELAY

- IGP RELAY

- WIPER FUSE

- WASHER FUSE

*5

LEVEL WARNING SWITCH ASSEMBLY

-

-

ILLUSTRATION

*1

STEERING WHEEL SWITCH HOUSING

*2

WINDSHIELD WIPER SWITCH ASSEMBLY

*3

WINDSHIELD WIPER RELAY ASSEMBLY

*4

MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

*5

POWER DISTRIBUTION BOX ASSEMBLY

- IGR NO. 1 RELAY

- ECU-IGR NO. 3 FUSE

*6

COMBINATION METER ASSEMBLY

*7

STEERING SENSOR

*8

DLC3

System Diagram

SYSTEM DIAGRAM

FRONT WIPER AND WASHER SYSTEM

WASHER FLUID LEVEL WARNING SYSTEM(w/ Level Warning Switch Assembly)

How To Proceed With Troubleshooting

HINT:

  • Use the following procedure to troubleshoot the wiper and washer system.
  • *: Use the GTS.

PROCEDURE

  1. Toyota Prius Vehicle BROUGHT TO WORKSHOP

NEXT
  1. CUSTOMER PROBLEM ANALYSIS

HINT:

  • In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
  • Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
  • The following 5 items are important points for problem analysis:

    What

    Toyota Prius Vehicle model, system name

    When

    Date, time, occurrence frequency

    Where

    Road conditions

    Under what conditions?

    Driving conditions, weather conditions

    How did it happen?

    Problem symptoms

NEXT
  1. PRE-CHECK

(a) Measure the auxiliary battery voltage with ignition switch off.

Standard Voltage:

11 to 14 V

If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.

(b) Check the fuses and relays.

(c) Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.

NEXT
  1. CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*

(a) Using the GTS, check for CAN communication system DTCs.

  • for HEV Model:

    Click here

  • for PHEV Model:

    Click here

Result

Proceed to

CAN DTCs are not output

A

CAN DTCs are output

B

B

GO TO CAN COMMUNICATION SYSTEM

  • for HEV Model:

    Click here

  • for PHEV Model:

    Click here

A
  1. CHECK FOR DTC*

(a) Check for DTCs.

Body Electrical > Main Body > Trouble Codes

Result

Proceed to

DTCs are not output

A

DTCs are output

B

B

GO TO DIAGNOSTIC TROUBLE CODE CHART

A
  1. PROBLEM SYMPTOMS TABLE

(a) Refer to Problem Symptoms Table.

Click here

Result

Proceed to

Fault is not listed in Problem Symptoms Table

A

Fault is listed in Problem Symptoms Table

B

B

GO TO PROBLEM SYMPTOMS TABLE

A
  1. OVERALL ANALYSIS AND TROUBLESHOOTING*

(a) Operation Check

Click here

(b) Customize Parameters

Click here

(c) Terminals of ECU

Click here

(d) Data List / Active Test

Click here

(e) Inspection

(f) On-Toyota Prius vehicle Inspection

NEXT
  1. ADJUST, REPAIR OR REPLACE

NEXT
  1. CONFIRMATION TEST

NEXT

END

Operation Check

OPERATION CHECK

CHECK FRONT WIPER CONTROL (w/ Auto Wiper System)

(a) Auto wiper function

(1) Continuously apply water to the windshield glass in front of the rain sensor.

(2) Turn the ignition switch to ON.

(3) Move the front wiper switch to the AUTO position.

(4) Check that the front wipers operate.

(b) Intermittent control function

HINT:

When the AUTO wiper function is disabled through a customize setting, the intermittent control function can be operated.

Click here

(1) Turn the ignition switch to ON.

(2) Move the front wiper switch to the AUTO position.

(3) Check that the intermittent operation interval can be adjusted between approximately 4 and 12.5 seconds by operating the auto sensitivity adjustment switch.

(c) Toyota Prius Vehicle speed sensing type adjustable intermittent wiper control function

HINT:

When the AUTO wiper function is disabled through a customize setting, the intermittent control function can be operated.

Click here

(1) Turn the ignition switch to ON.

(2) Move the front wiper switch to the AUTO position.

(3) Check that the intermittent operation interval changes between approximately 1.5 and 11 seconds according to the Toyota Prius vehicle speed and the position of the auto sensitivity adjustment switch.

(d) Door open linked wiper suspend function

(1) Continuously apply water to the windshield glass in front of the rain sensor.

(2) Turn the ignition switch to ON.

(3) Move the front wiper switch to the AUTO position and check that the front wipers operate.

(4) Open the driver door or front passenger door and check that the front wipers stop.

(5) Close the driver door or front passenger door and check that the front wipers re-operates.

CHECK FRONT WIPER CONTROL (w/o Auto Wiper System)

(a) Intermittent control function

(1) Turn the ignition switch to ON.

(2) Move the front wiper switch to the INT position.

(3) Check that the intermittent operation interval can be adjusted between approximately 4 and 12.5 seconds by operating the intermittent time adjustment switch.

(b) Toyota Prius Vehicle speed sensing type adjustable intermittent wiper control function

(1) Turn the ignition switch to ON.

(2) Move the front wiper switch to the INT position.

(3) Check that the intermittent operation interval changes between approximately 1.5 and 11 seconds according to the vehicle speed and the position of the intermittent time adjustment switch.

CHECK WASHER CONTROL

(a) Front washer cooperation

(1) Turn the ignition switch to ON.

(2) Hold the washer switch in the Fr WASH position for approximately 0.5 seconds or more and check that the front wipers operate in LO and washer fluid is sprayed.

(3) Release the washer switch and check that the front wipers operate for 3 cycles.

(b) Drip prevention wiper function

NOTICE:

Perform this inspection with the Toyota Prius vehicle stopped.

(1) Turn the ignition switch to ON.

(2) Operate the washers and check that approximately 3 seconds after front washer cooperation operates, the wipers operate 1 cycle.

CHECK REAR CAMERA WASHER SYSTEM (w/ Rear Camera Cleaner System)

(a) Combination switch

(1) Turn the ignition switch to ON.

(2) Hold the washer switch in the Rr WASH position and check that the rear television camera assembly is sprayed with washer fluid.

(b) Multimedia switch

(1) One push

  • The rear camera washer operates for a certain amount of time.

(2) Pressed and held

  • The rear camera washer operates while the multimedia switch is pressed and held.

LEVEL WARNING OPERATION INSPECTION(w/ Level Warning Switch Assembly)

(a) When the volume of washer fluid decreases to below a certain level (when the level warning switch is turned on), the multi-information display warns the driver by displaying a message.

Customize Parameters

CUSTOMIZE PARAMETERS

CUSTOMIZE WIPER AND WASHER SYSTEM

NOTICE:

  • When the customer requests a change in a function, first make sure that the function can be customized.
  • Be sure to make a note of the current settings before customizing.
  • When troubleshooting a function, first make sure that the function is set to the default setting.

HINT:

The following items can be customized.

(a) Select the setting by referring to the table below.

Wiper

Tester Display

Description

Default

Setting

ECU

Auto Wiper Function

Function to enable AUTO wiper operation*

Avail

$00:Enable,$01:Disable

Main body ECU (Multiplex network body ECU)

HINT:

  • Changes to the customize settings will not be applied until the ignition switch is turned off then ON.
  • *: w/ Auto Wiper System
Others

Tester Display

Description

Default

Setting

ECU

Wiper Voice Control Function

Function to enable the wiper-linked voice recognition operation function*

Enable

$00:Disable,$01:Enable

Main body ECU (Multiplex network body ECU)

  • *: w/ Body Device Voice Recognition Function

HINT:

Changes to the customize settings will not be applied until the ignition switch is turned off then ON.

Problem Symptoms Table

PROBLEM SYMPTOMS TABLE

NOTICE:

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

HINT:

  • Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
  • Inspect the fuses and relays related to this system before inspecting the suspected areas below.
Front Wiper System (w/ Auto Wiper System)

Symptom

Suspected Area

Link

Front wipers do not operate at all

Proceed to "Wiper and Washer Switch Circuit"

Proceed to "Front Wiper Motor Circuit"

Main body ECU (Multiplex network body ECU)

Windshield wiper relay assembly

Front wipers do not operate in AUTO

Check customize parameters (Auto wiper)

Rain sensor tape (Check for air bubbles)

-

Proceed to "Wiper and Washer Switch Circuit"

Rain sensor

Front wipers do not operate in LO

Proceed to "Wiper and Washer Switch Circuit"

Proceed to "Front Wiper Motor Circuit"

Windshield wiper relay assembly

Front wipers do not operate in HI

Proceed to "Wiper and Washer Switch Circuit"

Proceed to "Front Wiper Motor Circuit"

Windshield wiper relay assembly

Front wipers do not operate in INT*

Proceed to "Wiper and Washer Switch Circuit"

Front wipers do not operate in MIST

Proceed to "Wiper and Washer Switch Circuit"

Windshield wiper relay assembly

When the front wipers are operating in AUTO, the rain sensor sensitivity cannot be adjusted by the auto sensitivity adjustment switch (wiping interval does not change)

Proceed to "Wiper and Washer Switch Circuit"

When the front wipers are operating in AUTO, the wiper interval does not change according to changes in the Toyota Prius vehicle speed

Rain sensor

Main body ECU (Multiplex network body ECU)

When the front wipers are operating in INT, the front wiper intermittent operation interval cannot be adjusted by the auto sensitivity adjustment switch (wiping interval does not change)*

Proceed to "Wiper and Washer Switch Circuit"

When the front wipers are operating in INT, the front wiper intermittent operation interval does not change according to changes in the Toyota Prius vehicle speed*

Main body ECU (Multiplex network body ECU)

Front wipers continuously operate in AUTO

Proceed to "Wiper and Washer Switch Circuit"

Front wipers continuously operate in LO

Proceed to "Wiper and Washer Switch Circuit"

Front wipers continuously operate in HI

Proceed to "Wiper and Washer Switch Circuit"

Front wipers continuously operate in INT*

Proceed to "Wiper and Washer Switch Circuit"

When the customize setting "Auto Wiper" is changed, the operation of the wiper system does not change

Rain sensor

When the front wiper switch is turned off, the front wipers stop in the wrong position

Proceed to "Front Wiper Motor Circuit"

Check the automatic stop (park) position

Windshield wiper relay assembly

  • *: When the customize setting "Auto Wiper" is set to "Not Avl".
Front Wiper System (w/o Auto Wiper System)

Symptom

Suspected Area

Link

Front wipers do not operate at all

Proceed to "Wiper and Washer Switch Circuit"

Proceed to "Front Wiper Motor Circuit"

Main body ECU (Multiplex network body ECU)

Windshield wiper relay assembly

Front wipers do not operate in LO

Proceed to "Wiper and Washer Switch Circuit"

Proceed to "Front Wiper Motor Circuit"

Windshield wiper relay assembly

Front wipers do not operate in HI

Proceed to "Wiper and Washer Switch Circuit"

Proceed to "Front Wiper Motor Circuit"

Windshield wiper relay assembly

Front wipers do not operate in INT

Proceed to "Wiper and Washer Switch Circuit"

Proceed to "Front Wiper Motor Circuit"

Windshield wiper relay assembly

Front wipers do not operate in MIST

Proceed to "Wiper and Washer Switch Circuit"

Windshield wiper relay assembly

When the front wiper switch is in INT, the front wiper intermittent operation interval cannot be adjusted by the intermittent time adjustment switch

Proceed to "Wiper and Washer Switch Circuit"

Main body ECU (Multiplex network body ECU)

When the front wipers are operating in INT, the front wiper intermittent operation interval does not change according to changes in the Toyota Prius vehicle speed

Main body ECU (Multiplex network body ECU)

Front wipers continuously operate in LO

Proceed to "Wiper and Washer Switch Circuit"

Windshield wiper relay assembly

Front wipers continuously operate in HI

Proceed to "Wiper and Washer Switch Circuit"

Windshield wiper relay assembly

Front wipers continuously operate in INT

Proceed to "Wiper and Washer Switch Circuit"

Front wipers do not move to the service position (wiper operation is normal)

Main body ECU (Multiplex network body ECU)

When the front wiper switch is turned off, the front wipers do not move to the park position or stop in the wrong position

Proceed to "Front Wiper Motor Circuit"

Check the automatic stop (park) position

Windshield wiper relay assembly

Washer System

Symptom

Suspected Area

Link

Windshield washer motor and pump assembly does not operate

Proceed to "Wiper and Washer Switch Circuit"

Proceed to "Washer Motor Circuit"

Windshield wiper relay assembly

Front washers do not operate

Proceed to "Wiper and Washer Switch Circuit"

Windshield wiper relay assembly

Washer fluid does not flow (Windshield washer motor and pump assembly is normal)

Washer fluid

-

Washer hose and nozzle

-

Rear Camera Washer System (w/ Rear Camera Cleaner System)

Symptom

Suspected Area

Link

Washer motor and pump assembly does not operate

Proceed to "Rear Cleaner Motor and Relay Circuit"

Proceed to "Wiper and Washer Switch Circuit"

Main body ECU (multiplex network body ECU)

Washer fluid does not flow (Washer motor and pump assembly is normal)

Washer fluid

-

Washer hose, camera cleaner nozzle

-

Washer Fluid Level Warning System

Symptom

Suspected Area

Link

"Windshield Washer Fluid Low" is displayed on the multi-information display when washer fluid level is not low

Proceed to "Washer Fluid Level Warning Switch Circuit"

"Windshield Washer Fluid Low" is not displayed on the multi-information display when washer fluid level is low

Washer fluid

-

Proceed to "Washer Fluid Level Warning Switch Circuit"

Terminals Of Ecu

TERMINALS OF ECU

CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND POWER DISTRIBUTION BOX ASSEMBLY

(a) Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.

Click here

(b) Reconnect the power distribution box assembly connectors.

(c) Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

z1-13 (GND1) - Body ground

Ground

Always

Below 1 Ω

z1-14 (GND2) - Body ground

Ground

Always

Below 1 Ω

z1-26 (BECU) - Body ground

Auxiliary battery power supply

Always

11 to 14 V

z1-27 (IGR) - Body ground

IG power supply

Ignition switch off

Below 1 V

Ignition switch ON

11 to 14 V

z1-22 - Body ground

CXPI communication line

Ignition switch off

Below 1 V

Ignition switch ON

Pulse generation

z1-15 (LIN2) - Body ground

LIN communication line

Ignition switch ON

Pulse generation

(d) Connect the power distribution box assembly and main body ECU (multiplex network body ECU) connectors.

(e) Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

K17-12 (WHI) - Body ground

Windshield wiper motor assembly HI operation signal

Windshield wiper motor and link assembly operating in LO

9 to 14 V

Windshield wiper motor and link assembly operating in HI

Below 1 V

K16-11 (LIN4) - Body ground

LIN communication line

Ignition switch ON

Pulse generation

K17-6 (WPS) - Body ground

Wiper Relay operation signal

Ignition switch ON

11 to 14 V

Less than approximately 60 seconds after ignition switch turned off

Approximately 60 seconds or more after ignition switch turned off

Below 1 V

CHECK WINDSHIELD WIPER RELAY ASSEMBLY

(a) Disconnect the A55 and A56 windshield wiper relay assembly connectors.

(b) Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

A55-3 (E) - Body ground

Ground

Always

Below 1 Ω

A55-5 (EWS) - Body ground

Ground

Always

Below 1 Ω

A55-6 (IGWS) - Body ground

Washer circuit IG power source

Ignition switch ON

11 to 14 V

A55-8 ( B) - Body ground

Ignition switch ON signal (Power source circuit)

Ignition switch ON

11 to 14 V

Less than approximately 60 seconds after ignition switch turned off

Approximately 60 seconds or more after ignition switch turned off

Below 1 V

A56-5 (ES) - Body ground

Ground

Always

Below 1 Ω

(c) Connect the A55 and A56 windshield wiper relay assembly connectors.

(d) Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

A55-1 ( WR) - Body ground

Front washer operation signal

Ignition switch ON, front washer operating

11 to 14 V

A55-2 ( 1) - Body ground

LO operation signal to windshield wiper motor assembly

Ignition switch ON, windshield wiper motor assembly operating in LO

11 to 14 V

A55-4 ( 2) - Body ground

HI operation signal to windshield wiper motor assembly

Ignition switch ON, windshield wiper motor assembly operating in HI

11 to 14 V

A55-7 (-WR) - Body ground

Rear washer operation signal

Ignition switch ON, rear washer operating

11 to 14 V

A56-3 (2S) - Body ground

Windshield wiper motor assembly HI operation signal

Approximately 60 seconds or more after ignition switch turned off

4.5 to 5.5 V

Windshield wiper motor assembly operating in LO

9 to 14 V

Windshield wiper motor assembly operating in HI

Below 1 V

A56-4 (MPX1) - Body ground

CXPI communication line

Ignition switch ON

Pulse generation

A56-6 ( SM) - Body ground

Windshield wiper motor assembly position detection signal

Windshield wiper motor assembly in LO or HI operation

Below 1 V ←→ 11 to 14 V

Windshield wiper motor assembly stopped

Below 1 V

CHECK RAIN SENSOR (w/ Auto Wiper System)

(a) Disconnect the U4 rain sensor connector.

(b) Measure the voltage and resistance and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

U4-2 (ES) - Body ground

Ground

Always

Below 1 Ω

U4-3 (MPX) - Body ground

LIN communication signal

Ignition switch ON

Pulse generation

U4-4 (SIG) - Body ground

IG power source circuit

Ignition switch ON

11 to 14 V

Fail-safe Chart

FAIL-SAFE CHART

RAIN SENSOR FAIL-SAFE FUNCTION (w/ Auto Wiper System)

(a) The rain sensor performs fail-safe functions when it cannot properly receive necessary signals for wiper system control or a wiper system component is malfunctioning.

Item

Fail-safe Function

Conditions to Return to Normal Condition

Rain sensor voltage is too low

Continues control according to the conditions detected before the malfunction

Rain sensor voltage returns to normal

The rain sensor temperature is excessively high (90 °C or higher)

Stops the wiper operation

Rain sensor returns to normal

The rain sensor temperature is excessively low (-15°C (5°F) or lower)

Rain sensor LIN communication error

LIN communication returns to normal

Abnormal rain sensor signal

Performs intermittent operation according to the position of the auto sensitivity adjustment switch

Rain sensor returns to normal

Data List / Active Test

DATA LIST / ACTIVE TEST

DATA LIST

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

(a) Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Wiper Motor Cam Switch 1

Front wiper stop position status

OFF or ON

OFF: Front wiper not at bottom of stroke

ON: Front wiper at bottom of stroke

-

Wiper Control Switch HI

Front wiper switch HI position signal

OFF or ON

OFF: Front wiper switch not in HI position

ON: Front wiper switch in HI position

-

Rain Sensor Status

Rain sensor temperature circuit condition

Normal or Error

Normal: Rain sensor is normal

Error: Malfunction in rain sensor thermistor

w/ Auto Wiper System

Rain Sensor Level Status

Rain sensor output condition

Normal or Error

Normal: Rain sensor is normal

Error: Malfunction in rain sensor thermistor output

w/ Auto Wiper System

Rain Sensor High Temperature Status

Rain sensor high temperature condition

Normal or Error

Normal: Rain sensor is normal

Error: Rain sensor temperature is high

w/ Auto Wiper System

Rain Sensor Low Temperature Status

Rain sensor low temperature condition

Normal or Error

Normal: Rain sensor is normal

Error: Rain sensor temperature is low

w/ Auto Wiper System

Wiper Switch Auto Signal

Windshield wiper switch assembly (AUTO position) condition

OFF or ON

OFF: Windshield wiper switch assembly not in AUTO position

ON: Windshield wiper switch assembly in AUTO position

w/ Auto Wiper System

Wiper Operation Request (from other system)

Status of wiper operation request from other system

OFF or ON

OFF: Not requested

ON: Requested

w/ Auto Wiper System

Wiper Motor Control Status

Wiper motor control condition in response to rain sensor request

Normal, Normal (Link Ctrl), Normal (Req Deny), Abnormal or Normal (Wiper Ctrl)

Current motor control condition

w/ Auto Wiper System

Wiper Intermittent Time Volume

Auto sensitivity adjustment volume condition

Shortest, Shorter, Longer or Longest

Shortest: Windshield wiper switch assembly (auto sensitivity adjustment volume condition) P4 position

Shorter: Windshield wiper switch assembly (auto sensitivity adjustment volume condition) P3 position

Longer: Windshield wiper switch assembly (auto sensitivity adjustment volume condition) P2 position

Longest: Windshield wiper switch assembly (auto sensitivity adjustment volume condition) P1 position

*

Automatic Wiper Wiping Mode (Sensor to Wiper)

Status of command request signal for front wiper speed and intermittent time from rain sensor

Stop, LO Mode, HI Mode, Wait, INT Mode1 (Toyota Prius Vehicle Stop), INT Mode2 (Vehicle Stop), INT Mode3 (Vehicle Stop), INT Mode4 (Vehicle Stop), INT Mode5 (Vehicle Stop), INT Mode6 (Vehicle Stop), INT Mode7 (Vehicle Stop), INT Mode1 (Vehicle Run), INT Mode2 (Vehicle Run), INT Mode3 (Vehicle Run), INT Mode4 (Vehicle Run), INT Mode5 (Vehicle Run), INT Mode6 (Vehicle Run), INT Mode7 (Toyota Prius Vehicle Run), INT Mode (Sensor Abnormal), OFF (Customize) or Fail Stop

Stop: Windshield wiper switch assembly in AUTO position and stop requested (Windshield wiper switch assembly OFF included) (because rain not detected)

LO Mode: Windshield wiper switch assembly in AUTO position and LO operation requested

HI Mode: Windshield wiper switch assembly in AUTO position and HI operation requested

Wait: Rain sensor is judging wiping mode

INT Mode 1 (Toyota Prius Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 32.7 s

INT Mode 2 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 17.5 s

INT Mode 3 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 9.7 s

INT Mode 4 (Toyota Prius Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 5.4 s

INT Mode 5 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 3.1 s

INT Mode 6 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 1.6 s

INT Mode 7 (Toyota Prius Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 0.8 s

INT Mode 1 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 17.9 s

INT Mode 2 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 10.1 s

INT Mode 3 (Toyota Prius Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 5.9 s

INT Mode 4 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 3.5 s

INT Mode 5 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 2.1 s

INT Mode 6 (Toyota Prius Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 1.2 s

INT Mode 7 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 0.6 s

INT Mode (Sensor Abnormal): Windshield wiper switch assembly in AUTO position and speed sensing intermittent operation requested

OFF (Customize): Windshield wiper switch assembly in AUTO position and stop requested (for customization)

Fail Stop: Windshield wiper switch assembly in AUTO position and stop requested (sensor malfunction)

w/ Auto Wiper System

Rain Sensor

Rain sensor detection information

With or Without

With: w/ Rain Sensor

Without: w/o Rain Sensor

w/ Auto Wiper System

Wiper LO Single Operation Signal

Wiper LO single operation signal

With or Without

With: Windshield wiper switch assembly in AUTO position and sensor determines small amount of rain while wiper is in stopped position

Without: Windshield wiper switch assembly in AUTO position and wiper in position other than stopped

w/ Auto Wiper System

Communication Wiper ECU

Connection status between windshield wiper motor assembly and main body ECU (multiplex network body ECU)

STOP or OK

STOP: Not Connected

OK: Connected

Although this item is displayed on the GTS, it is not applicable to this Toyota Prius vehicle.

Communication Wiper Module

Connection status between windshield wiper relay assembly and main body ECU (multiplex network body ECU)

STOP or OK

STOP: Not Connected

OK: Connected

DTCs are stored if a malfunction occurs in the CXPI communication system.

Communication Humidity/Rain Sensor

Connection status between rain sensor and main body ECU (multiplex network body ECU)

STOP or OK

STOP: Not Connected

OK: Connected

w/ Auto Wiper System

R Wiper Stop Function at Back Door/Trunk Lid Open

Function to enable the back door open linked rear wiper suspend function

Enable or Disable

Customize setting displayed

Although this item is displayed on the GTS, it is not applicable to this Toyota Prius vehicle.

Auto Wiper Function

Function to enable the auto wiper function

Enable or Disable

Customize setting displayed

-

Wiper Voice Control Function

Function to enable the voice recognition function

Enable or Disable

Customize setting displayed

-

  • *: Refer to Inspection for each position of the switch.

    Click here

Body Electrical > Combination Meter > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Washer Level Warning Switch

Washer fluid level warning switch status

Washer Level Switch ON, Washer Level Switch OFF or Unknown

Washer Level Switch ON: Washer fluid level not low

Washer Level Switch OFF: Washer fluid level low

Unknown: Washer fluid level not detected

-

Wiper Switch

Front wiper switch OFF position signal

OFF or ON

OFF: Front wiper switch not in OFF position

ON: Front wiper switch in OFF position

-

Wiper Switch (AUTO/INT)

Front wiper switch AUTO*1 or INT*2 position signal

OFF or ON

OFF: Front wiper switch not in AUTO*1 or INT*2 position

ON: Front wiper switch in AUTO*1 or INT*2 position

-

Wiper Switch (LO)

Front wiper switch LO position signal

OFF or ON

OFF: Front wiper switch not in LO position

ON: Front wiper switch in LO position

-

Wiper Switch (HI)

Front wiper switch HI position signal

OFF or ON

OFF: Front wiper switch not in HI position

ON: Front wiper switch in HI position

-

Wiper Switch (MIST)

Front wiper switch MIST position signal

OFF or ON

OFF: Front wiper switch not in MIST position

ON: Front wiper switch in MIST position

-

Washer Switch

Washer switch Fr WASH position signal

OFF or ON

OFF: Washer switch not in Fr WASH position

ON: Washer switch in Fr WASH position

-

Wiper Switch (Intermittent)

Front wiper switch INT position signal

OFF or ON

OFF: Front wiper switch not in INT

ON: Front wiper switch in INT

*2

Rear Wiper Switch

Rear wiper switch position signal

OFF or ON

OFF: Rear wiper switch not in ON position

ON: Rear wiper switch in ON position

Although this item is displayed on the GTS, it is not applicable to this Toyota Prius vehicle.

Rear Washer Switch

Washer switch Rr WASH position signal

OFF or ON

OFF: Washer switch not in Rr WASH position

ON: Washer switch in Rr WASH position

*3

Wiper Speed (FAST)

Intermittent time adjustment volume condition

OFF or ON

OFF: Windshield wiper switch assembly (auto sensitivity adjustment volume condition) not in P4 position

ON: Windshield wiper switch assembly (auto sensitivity adjustment volume condition) in P4 position

*4

Wiper Speed (2nd FAST)

Intermittent time adjustment volume condition

OFF or ON

OFF: Windshield wiper switch assembly (auto sensitivity adjustment volume condition) not in P3 position

ON: Windshield wiper switch assembly (auto sensitivity adjustment volume condition) in P3 position

*4

Wiper Speed (3rd FAST)

Intermittent time adjustment volume condition

OFF or ON

OFF: Windshield wiper switch assembly (auto sensitivity adjustment volume condition) not in P2 position

ON: Windshield wiper switch assembly (auto sensitivity adjustment volume condition) in P2 position

*4

Wiper Speed (SLOW)

Intermittent time adjustment volume condition

OFF or ON

OFF: Windshield wiper switch assembly (auto sensitivity adjustment volume condition) not in P1 position

ON: Windshield wiper switch assembly (auto sensitivity adjustment volume condition) in P1 position

*4

  • *1: w/ Auto Wiper System
  • *2: w/o Auto Wiper System
  • *3: w/ Rear Camera Cleaner System
  • *4: Refer to Inspection for each position of the switch.

    Click here

ACTIVE TEST

HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Wiper Power Relay

Function to operate the windshield wiper relay

OFF or ON

-

Front Washer Relay

Function to operate the windshield washer motor and pump assembly (Front)

OFF or ON

-

Front Wiper Lo Operation

Function to operate the windshield wiper motor assembly in LO

OFF or ON

-

Front Wiper Hi Operation

Function to operate the windshield wiper motor assembly in HI

OFF or ON

-

Rear Washer Relay

Function to operate the windshield washer motor and pump assembly (Rear)

OFF or ON

-

Humidity/Rain Sensor Missing Message (B127987)

DESCRIPTION

The main body ECU (multiplex network body ECU) and rain sensor communicate via LIN communication. The main body ECU (multiplex network body ECU) stores this DTC if communication becomes abnormal.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Memory

DTC Output from

Priority

B127987

Humidity/Rain Sensor Missing Message

Detection Condition:
  • Auxiliary battery voltage is 9.5 V or more
Malfunction Status:
  • Communication malfunction with rain sensor
Malfunction Duration:
  • 10 seconds or more
  • Rain sensor
  • Harness or connector
  • Main body ECU (multiplex network body ECU)

○

Main Body

A

WIRING DIAGRAM

NOTICE:

  • Inspect the fuses for circuits related to this system before performing the following procedure.
  • Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

PROCEDURE

  1. CHECK FOR DTC

(a) Check for DTCs.

Body Electrical > Main Body > Trouble Codes

Result

Proceed to

Only B127987 is output

A

B127987 and B276C88 are output

B

B

GO TO DTC B276C88

A
  1. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - RAIN SENSOR)

Pre-procedure1

(a) Disconnect the K16 main body ECU (multiplex network body ECU) connector.

(b) Disconnect the U4 rain sensor connector.

Procedure1

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(K16,U4) Click Connector(K16) Click Connector(U4)

Tester Connection

Condition

Specified Condition

Result

K16-11 (LIN4) - U4-3 (MPX)

Always

Below 1 Ω

Ω

Post-procedure1

(d) None

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

(a) Check for pulses according to the value(s) in the table below.

Standard Pulse:

Click Location & Routing(K16) Click Connector(K16)

Tester Connection

Condition

Specified Condition

K16-11 (LIN4) - Body ground

Ignition switch ON

Pulse generation

*a

Component without harness connected

(Main Body ECU (Multiplex Network Body ECU)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

OK
  1. CHECK HARNESS AND CONNECTOR (POWER SOURCE - RAIN SENSOR)

(a) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Click Location & Routing(U4) Click Connector(U4)

Tester Connection

Condition

Specified Condition

Result

U4-4 (SIG) - Body ground

Ignition switch ON

11 to 14 V

V

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (RAIN SENSOR - BODY GROUND)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(U4) Click Connector(U4)

Tester Connection

Condition

Specified Condition

Result

U4-2 (ES) - Body ground

Always

Below 1 Ω

Ω

OK

REPLACE RAIN SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

Rain Sensor Component Internal Failure (B140096)

DESCRIPTION

This DTC is stored when the rain sensor detects an internal malfunction.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Memory

DTC Output from

Priority

B140096

Rain Sensor Component Internal Failure

Detection Condition:
  • IG power source voltage is 9.5 V or more
Malfunction Status:
  • Either of the following is detected
    • Rain sensor internal thermistor malfunction detected for 10 seconds or more
    • LED output malfunction detected for 2 seconds or more

Rain sensor

○

Main Body

A

PROCEDURE

  1. CLEAR DTC

(a) Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
NEXT
  1. CHECK FOR DTC

(a) Read the DTCs.

Body Electrical > Main Body > Trouble Codes

Result

Proceed to

B140096 is not output

A

B140096 is output

B

A

USE SIMULATION METHOD TO CHECK

B

REPLACE RAIN SENSOR

Wiper Module Missing Message (B235787)

DESCRIPTION

The main body ECU (multiplex network body ECU) and windshield wiper relay assembly communicate via CXPI communication. The main body ECU (multiplex network body ECU) stores this DTC if communication becomes abnormal.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Memory

DTC Output from

Priority

B235787

Wiper Module Missing Message

Detection condition:
  • Auxiliary battery voltage is 9.5 V or more
Malfunction Status:
  • Communication malfunction between the main body ECU (multiplex network body ECU) and windshield wiper relay assembly
Malfunction Time:
  • 10 seconds or more
  • Windshield wiper relay assembly
  • Main body ECU (multiplex network body ECU)
  • Harness or connector
  • WIPER relay
  • Power distribution box assembly

○

Main Body

A

WIRING DIAGRAM

NOTICE:

  • Inspect the fuses of circuits related to this system before performing the following procedure.
  • Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

PROCEDURE

  1. CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

Pre-procedure1

(a) Disconnect the A56 windshield wiper relay assembly connector.

(b) Disconnect the A12 power distribution box assembly connector.

Procedure1

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(A56,A12) Click Connector(A56) Click Connector(A12)

Tester Connection

Condition

Specified Condition

A56-4 (MPX1) - A12-5

Always

Below 1 Ω

A56-4 (MPX1) or A12-5 - Body ground

Always

10 kΩ or higher

Post-procedure1

(d) None

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

(a) Check for voltage and pulses according to the value(s) in the table below.

Standard Voltage and Pulse:

Click Location & Routing(A12) Click Connector(A12)

Tester Connection

Condition

Specified Condition

A12-5 - Body ground

Ignition switch ON

Pulse generation

Ignition switch off

Below 1 V

*a

Component without harness connected

(Power Distribution Box Assembly)

NG

GO TO STEP 12

OK
  1. PERFORM ACTIVE TEST USING GTS

(a) Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Wiper Power Relay

Function to operate the Windshield Wiper relay

OFF or ON

-

Body Electrical > Main Body > Active Test

Wiper Power Relay

OK:

Windshield Wiper relay operates normally.

NG

GO TO STEP 9

OK
  1. CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - BODY GROUND)

Pre-procedure1

(a) Disconnect the A55 windshield wiper relay assembly connector.

Procedure1

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(A55,A56) Click Connector(A55) Click Connector(A56)

Tester Connection

Condition

Specified Condition

A55-3 (E) - Body ground

Always

Below 1 Ω

A56-5 (ES) - Body ground

Always

Below 1 Ω

Post-procedure1

(c) None

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (POWER SOURCE - WINDSHIELD WIPER RELAY ASSEMBLY)

(a) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Click Location & Routing(A55) Click Connector(A55)

Tester Connection

Condition

Specified Condition

A55-8 ( B) - Body ground

Ignition switch ON

11 to 14 V

Less than approximately 60 seconds after ignition switch turned off

11 to 14 V

Approximately 60 seconds or more after ignition switch turned off

Below 1 V

OK

REPLACE WINDSHIELD WIPER RELAY ASSEMBLY

NG
  1. INSPECT WINDSHIELD WIPER RELAY

HINT:

Click here

NG

REPLACE WINDSHIELD WIPER RELAY

OK
  1. CHECK HARNESS AND CONNECTOR (POWER SOURCE - WINDSHIELD WIPER RELAY)

(a) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

5 (Windshield Wiper Relay) - Body ground

Ignition switch off

11 to 14 V

*1

NO. 1 ENGINE ROOM RELAY BLOCK AND NO. 1 JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - WINDSHIELD WIPER RELAY)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(A55) Click Connector(A55)

Tester Connection

Condition

Specified Condition

A55-8 ( B) - 3 (Windshield Wiper Relay)

Always

Below 1 Ω

A55-8 ( B) or 3 (Windshield Wiper Relay) - Body ground

Always

10 kΩ or higher

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. INSPECT WINDSHIELD WIPER RELAY

HINT:

Click here

NG

REPLACE WINDSHIELD WIPER RELAY

OK
  1. CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

Pre-procedure1

(a) Disconnect the K17 main body ECU (multiplex network body ECU) connector.

Procedure1

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(K17) Click Connector(K17)

Tester Connection

Condition

Specified Condition

2 (Windshield Wiper Relay) - K17-6 (WPS)

Always

Below 1 Ω

2(Windshield Wiper Relay) or K17-6 (WPS) - Body ground

Always

10 kΩ or higher

Result:

Proceed to

OK

NG

*1

NO. 1 ENGINE ROOM RELAY BLOCK AND NO. 1 JUNCTION BLOCK ASSEMBLY

Post-procedure1

(c) None

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY - BODY GROUND)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

1 (Windshield Wiper Relay) - Body ground

Always

Below 1 Ω

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. CHECK POWER DISTRIBUTION BOX ASSEMBLY

Pre-procedure1

(a) Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.

HINT:

Click here

Procedure1

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(A12,z1) Click Connector(A12) Click Connector(z1)

Tester Connection

Condition

Specified Condition

A12-5 - z1-22 (CXP1)

Always

Below 1 Ω

A12-5 or z1-22 (CXP1) - Body ground

Always

10 kΩ or higher

Result:

Pre-procedure1

Proceed to

OK

NG

*a

Component without harness connected

(Power Distribution Box Assembly)

Post-procedure1

(c) None

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

Front Wiper Motor Circuit

DESCRIPTION

The windshield wiper relay assembly controls the windshield wiper motor assembly through this circuit.

WIRING DIAGRAM

PROCEDURE

  1. PERFORM ACTIVE TEST USING GTS

(a) Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Front Wiper Lo Operation

Function to operate the windshield wiper motor assembly in LO

OFF or ON

-

Front Wiper Hi Operation

Function to operate the windshield wiper motor assembly in HI

OFF or ON

-

Body Electrical > Main Body > Active Test

Front Wiper Lo Operation

Body Electrical > Main Body > Active Test

Front Wiper Hi Operation

OK:

Windshield wiper motor assembly operates normally.

OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG
  1. INSPECT WINDSHIELD WIPER MOTOR ASSEMBLY

(a) Remove the windshield wiper motor assembly.

Click here

(b) Inspect the windshield wiper motor assembly.

Click here

NG

REPLACE WINDSHIELD WIPER MOTOR ASSEMBLY

OK
  1. CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - WINDSHIELD WIPER MOTOR ASSEMBLY)

(a) Disconnect the A55 and A56 windshield wiper relay assembly connectors.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

for 2ZR-FXE Click Location & Routing(A55,A43,A56) Click Connector(A55) Click Connector(A43) Click Connector(A56)

Tester Connection

Condition

Specified Condition

A55-2 ( 1) - A43-1 ( 1)

Always

Below 1 Ω

A55-4 ( 2) - A43-4 ( 2)

Always

Below 1 Ω

A56-6 ( SM) - A43-3 ( S)

Always

Below 1 Ω

A55-2 ( 1) or A43-1 ( 1) - Body ground

Always

10 kΩ or higher

A55-4 ( 2) or A43-4 ( 2) - Body ground

Always

10 kΩ or higher

A56-6 ( SM) or A43-3 ( S) - Body ground

Always

10 kΩ or higher

Standard Resistance:

for M20A-FXS Click Location & Routing(A55,A44,A56) Click Connector(A55) Click Connector(A44) Click Connector(A56)

Tester Connection

Condition

Specified Condition

A55-2 ( 1) - A44-5 ( 1)

Always

Below 1 Ω

A55-4 ( 2) - A44-3 ( 2)

Always

Below 1 Ω

A56-6 ( SM) - A44-1 ( S)

Always

Below 1 Ω

A55-2 ( 1) or A44-5 ( 1) - Body ground

Always

10 kΩ or higher

A55-4 ( 2) or A44-3 ( 2) - Body ground

Always

10 kΩ or higher

A56-6 ( SM) or A44-1 ( S) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER MOTOR ASSEMBLY - BODY GROUND)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

for 2ZR-FXE Click Location & Routing(A43) Click Connector(A43)

Tester Connection

Condition

Specified Condition

A43-5 (E) - Body ground

Always

Below 1 Ω

Standard Resistance:

for M20A-FXS Click Location & Routing(A44) Click Connector(A44)

Tester Connection

Condition

Specified Condition

A44-4 (E) - Body ground

Always

Below 1 Ω

OK

REPLACE WINDSHIELD WIPER RELAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

Wiper and Washer Switch Circuit

DESCRIPTION

The condition of the windshield wiper switch assembly is detected and sent to the steering sensor in this circuit.

WIRING DIAGRAM

PROCEDURE

  1. READ VALUE USING GTS

(a) Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Wiper Switch

Front wiper switch OFF position signal

OFF or ON

OFF: Front wiper switch not in OFF position

ON: Front wiper switch in OFF position

-

Wiper Switch (AUTO/INT)

Front wiper switch AUTO*1 or INT*2 position signal

OFF or ON

OFF: Front wiper switch not in AUTO*1 or INT*2 position

ON: Front wiper switch in AUTO*1 or INT*2 position

-

Wiper Switch (LO)

Front wiper switch LO position signal

OFF or ON

OFF: Front wiper switch not in LO position

ON: Front wiper switch in LO position

-

Wiper Switch (HI)

Front wiper switch HI position signal

OFF or ON

OFF: Front wiper switch not in HI position

ON: Front wiper switch in HI position

-

Wiper Switch (MIST)

Front wiper switch MIST position signal

OFF or ON

OFF: Front wiper switch not in MIST position

ON: Front wiper switch in MIST position

-

Washer Switch

Washer switch Fr WASH position signal

OFF or ON

OFF: Washer switch not in Fr WASH position

ON: Washer switch in Fr WASH position

-

Wiper Switch (Intermittent)

Front wiper switch INT position signal

OFF or ON

OFF: Front wiper switch not in INT

ON: Front wiper switch in INT

*2

Rear Wiper Switch

Rear wiper switch position signal

OFF or ON

OFF: Rear wiper switch not in ON position

ON: Rear wiper switch in ON position

Although this item is displayed on the GTS, it is not applicable to this Toyota Prius vehicle.

Rear Washer Switch

Washer switch Rr WASH position signal

OFF or ON

OFF: Washer switch not in Rr WASH position

ON: Washer switch in Rr WASH position

-

Wiper Speed (FAST)

Intermittent time adjustment volume condition

OFF or ON

OFF: Windshield wiper switch assembly (auto sensitivity adjustment volume condition) not in P4 position

ON: Windshield wiper switch assembly (auto sensitivity adjustment volume condition) in P4 position

*3

Wiper Speed (2nd FAST)

Intermittent time adjustment volume condition

OFF or ON

OFF: Windshield wiper switch assembly (auto sensitivity adjustment volume condition) not in P3 position

ON: Windshield wiper switch assembly (auto sensitivity adjustment volume condition) in P3 position

*3

Wiper Speed (3rd FAST)

Intermittent time adjustment volume condition

OFF or ON

OFF: Windshield wiper switch assembly (auto sensitivity adjustment volume condition) not in P2 position

ON: Windshield wiper switch assembly (auto sensitivity adjustment volume condition) in P2 position

*3

Wiper Speed (SLOW)

Intermittent time adjustment volume condition

OFF or ON

OFF: Windshield wiper switch assembly (auto sensitivity adjustment volume condition) not in P1 position

ON: Windshield wiper switch assembly (auto sensitivity adjustment volume condition) in P1 position

*3

  • *1: w/ Auto Wiper System
  • *2: w/o Auto Wiper System
  • *3: Refer to Inspection for each position of the switch.

    Click here

Body Electrical > Combination Meter > Data List

Tester Display

Wiper Switch

Wiper Switch (AUTO/INT)

Wiper Switch (LO)

Wiper Switch (HI)

Wiper Switch (MIST)

Washer Switch

Wiper Switch (Intermittent)

Rear Wiper Switch

Rear Washer Switch

Wiper Speed (FAST)

Wiper Speed (2nd FAST)

Wiper Speed (3rd FAST)

Wiper Speed (SLOW)

OK:

The GTS display changes correctly in response to the windshield wiper switch assembly operation.

OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG
  1. INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY

(a) Remove the windshield wiper switch assembly.

Click here

(b) Inspect the windshield wiper switch assembly.

Click here

NG

REPLACE WINDSHIELD WIPER SWITCH ASSEMBLY

OK
  1. INSPECT STEERING WHEEL SWITCH HOUSING

(a) Remove the steering wheel switch housing.

Click here

(b) Inspect the steering wheel switch housing.

Click here

NG

REPLACE STEERING WHEEL SWITCH HOUSING

OK
  1. CHECK HARNESS AND CONNECTOR (STEERING SENSOR - WINDSHIELD WIPER RELAY ASSEMBLY)

(a) Disconnect the A56 windshield wiper relay assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(K72,A56) Click Connector(K72) Click Connector(A56)

Tester Connection

Condition

Specified Condition

K72-2 (2S) - A56-3 (2S)

Always

Below 1 Ω

K72-2 (2S) or A56-3 (2S) - Body ground

Always

10 kΩ or higher

OK

REPLACE WINDSHIELD WIPER RELAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

Rear Cleaner Motor and Relay Circuit

DESCRIPTION

When the main body ECU (multiplex network body ECU) receives a washer switch (Rr CAMERA WASH) signal from the windshield wiper switch assembly, the windshield washer motor and pump assembly operates to spray the windshield washer.

WIRING DIAGRAM

Click here

NOTICE:

  • First check that the windshield washer function operates normally.

    Click here

  • Inspect the fuses for circuits related to this system before performing the following procedure.
  • If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.

PROCEDURE

  1. PERFORM ACTIVE TEST USING GTS

(a) Perform the Active Test according to the display on the GTS.

Click here

Body Electrical > Main Body > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Rear Washer Relay

Operates the windshield washer motor and pump assembly

OFF or ON

-

Body Electrical > Main Body > Active Test

Rear Washer Relay

OK:

The windshield washer motor and pump assembly is operate normally.

OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG
  1. INSPECT WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY

(a) Remove the windshield washer motor and pump assembly.

Click here

(b) Inspect the windshield washer motor and pump assembly.

Click here

NG

REPLACE WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY

OK
  1. CHECK HARNESS AND CONNECTOR (POWER SOURCE - WINDSHIELD WIPER RELAY ASSEMBLY)

(a) Disconnect the A55 windshield wiper relay assembly connector.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Click Location & Routing(A55) Click Connector(A55)

Tester Connection

Condition

Specified Condition

A55-6 (IGWS) - Body ground

Ignition switch ON

11 to 14 V

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - BODY GROUND)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(A55) Click Connector(A55)

Tester Connection

Condition

Specified Condition

A55-5 (EWS) - Body ground

Always

Below 1 Ω

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(A55,A46) Click Connector(A55) Click Connector(A46)

Tester Connection

Condition

Specified Condition

A55-1 ( WR) - A46-1 (B)

Always

Below 1 Ω

A55-7 (-WR) - A46-2 (SW)

Always

Below 1 Ω

A55-1 ( WR) or A46-1 (B) - Body ground

Always

10 kΩ or higher

A55-7 (-WR) or A46-2 (SW) - Body ground

Always

10 kΩ or higher

OK

REPLACE WINDSHIELD WIPER RELAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

Washer Fluid Level Warning Switch Circuit

DESCRIPTION

When the washer fluid level is lower than a certain level, a warning message is displayed on the combination meter assembly.

WIRING DIAGRAM

NOTICE:

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another Toyota Prius vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

HINT:

The wiper and washer system uses the CAN and CXPI communication system. First, confirm that there is no malfunction in the CAN and CXPI communication system.

PROCEDURE

  1. READ VALUE USING GTS

(a) Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Washer Level Warning Switch

Washer fluid level warning switch status

Washer Level Switch ON, Washer Level Switch OFF or Unknown

Washer Level Switch ON: Washer fluid level not low

Washer Level Switch OFF: Washer fluid level low

Unknown: Washer fluid level not detected

-

Body Electrical > Combination Meter > Data List

Washer Level Warning Switch

OK:

The GTS display changes correctly in response to the washer fluid level warning switch status.

OK

REPLACE COMBINATION METER ASSEMBLY

NG
  1. INSPECT LEVEL WARNING SWITCH

(a) Inspect the level warning switch assembly.

(1) This check should be performed with the level warning switch installed to the windshield washer jar assembly and fill the washer jar with washer fluid.

*a

Component without harness connected

(Level Warning Switch Assembly)

(2) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(A45) Click Connector(A45)

Tester Connection

Condition

Specified Condition

A45-1(S) - A45-2(E)

Fluid volume is 600 to 800 cc (36.6 to 48.8 cu. in.) or higher*

10 kΩ or higher

Fluid volume is 600 to 800 cc (36.6 to 48.8 cu. in.) or lower*

Below 1 Ω

HINT:

  • Perform checks by reducing the amount of washer fluid.
  • *: The level warning switch assembly begins operating when the fluid volume is 600 to 800 cc (36.6 to 48.8 cu. in.) depending on the Toyota Prius vehicle condition.
NG

REPLACE WINDSHIELD WASHER JAR ASSEMBLY

OK
  1. CHECK HARNESS AND CONNECTOR (LEVEL WARNING SWITCH ASSEMBLY - COMBINATION METER ASSEMBLY)

(a) Disconnect the K19 combination meter assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(A45,K19) Click Connector(A45) Click Connector(K19)

Tester Connection

Condition

Specified Condition

A45-1 (S) - K19-36 (WLVL)

Always

Below 1 Ω

A45-1 (S) or K19-36 (WLVL) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (LEVEL WARNING SWITCH ASSEMBLY - BODY GROUND)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(A45) Click Connector(A45)

Tester Connection

Condition

Specified Condition

A45-2 (E) - Body ground

Always

Below 1 Ω

OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR