Radio Antenna Cord (for Instrument Panel)
- Removal
- Removal
- Installation
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during antenna cord sub-assembly removal/installation are shown below.
CAUTION:
Be sure to read Precaution thoroughly before servicing.

Click here ![]()
NOTICE:
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
Click here ![]()
HINT:
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when Toyota Prius vehicle is drivenEffect/Inoperative Function When Necessary Procedures are not Performed | Necessary Procedures | Link |
|---|---|---|
Front Camera System |
Drive the Toyota Prius vehicle straight ahead at 35 km/h or more for 5 seconds or more. |
Effect/Inoperative Function When Necessary Procedures are not Performed | Necessary Procedures | Link |
|---|---|---|
| *1: w/o Power Back Door System *2: w/ Power Back Door System |
||
Power Door Lock Control System*1
|
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. |
|
Power Back Door System*2 |
Reset back door close position |
|
Air Conditioning System |
After the ignition switch is turned to ON, the servo motor standard position is recognized. |
- |

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY |
- |
- |
- |
- |
2 |
DEFROSTER NOZZLE ASSEMBLY |
55950G |
- |
- |
- |
3 |
NO. 2 HEATER TO REGISTER DUCT SUB-ASSEMBLY |
55085 |
- |
- |
- |
4 |
ANTENNA CORD SUB-ASSEMBLY |
86101T |
- |
- |
- |
PROCEDURE
1. REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY
Click here ![]()
2. REMOVE DEFROSTER NOZZLE ASSEMBLY
Click here ![]()
3. REMOVE NO. 2 HEATER TO REGISTER DUCT SUB-ASSEMBLY
Click here ![]()
4. REMOVE ANTENNA CORD SUB-ASSEMBLY

Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during antenna cord sub-assembly removal/installation are shown below.
CAUTION:
Be sure to read Precaution thoroughly before servicing.

Click here ![]()
NOTICE:
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
Click here ![]()
HINT:
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when Toyota Prius vehicle is drivenEffect/Inoperative Function When Necessary Procedures are not Performed | Necessary Procedures | Link |
|---|---|---|
Front Camera System |
Drive the Toyota Prius vehicle straight ahead at 35 km/h or more for 5 seconds or more. |
Effect/Inoperative Function When Necessary Procedures are not Performed | Necessary Procedures | Link |
|---|---|---|
| *1: w/o Power Back Door System *2: w/ Power Back Door System |
||
Power Door Lock Control System*1
|
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. |
|
Power Back Door System*2 |
Reset back door close position |
|
Air Conditioning System |
for HEV Model:
|
- |

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY |
- |
- |
- |
- |
2 |
DEFROSTER NOZZLE ASSEMBLY |
55950G |
- |
- |
- |
3 |
NO. 2 HEATER TO REGISTER DUCT SUB-ASSEMBLY |
55085 |
- |
- |
- |
4 |
ANTENNA CORD SUB-ASSEMBLY |
86101T |
- |
- |
- |
PROCEDURE
1. REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY
Click here ![]()
2. REMOVE DEFROSTER NOZZLE ASSEMBLY
Click here ![]()
3. REMOVE NO. 2 HEATER TO REGISTER DUCT SUB-ASSEMBLY
Click here ![]()
4. REMOVE ANTENNA CORD SUB-ASSEMBLY

Installation
INSTALLATION
COMPONENTS (INSTALLATION)
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
ANTENNA CORD SUB-ASSEMBLY |
86101T |
- |
- |
- |
2 |
NO. 2 HEATER TO REGISTER DUCT SUB-ASSEMBLY |
55085 |
- |
- |
- |
3 |
DEFROSTER NOZZLE ASSEMBLY |
55950G |
- |
- |
- |
4 |
INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY |
- |
- |
- |
- |
PROCEDURE
1. INSTALL ANTENNA CORD SUB-ASSEMBLY
2. INSTALL NO. 2 HEATER TO REGISTER DUCT SUB-ASSEMBLY
3. INSTALL DEFROSTER NOZZLE ASSEMBLY
4. INSTALL INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY
Click here ![]()














