Roof Antenna
- Removal
- Installation
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during roof antenna removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/ReplacedReplaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
| *: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation. | |||
w/ Occupant Classification System:
|
Zero point calibration (Occupant classification system) |
|
|
CAUTION:
Be sure to read Precaution thoroughly before servicing.

Click here ![]()
NOTICE:
- After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
Click here

HINT:
- When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used. Learning completes when Toyota Prius vehicle is driven
Learning completes when vehicle is operated normallyEffect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
Front Camera System
Drive the Toyota Prius vehicle straight ahead at 35 km/h or more for 5 seconds or more.

Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
*1: w/o Power Back Door System *2: w/ Power Back Door System
Power Door Lock Control System*1
- Back door opener
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.

Power Back Door System*2
Reset back door close position

Air Conditioning System
After the ignition switch is turned to ON, the servo motor standard position is recognized.
-

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
ROOF HEADLINING ASSEMBLY |
- |
- |
- |
- |
*A |
for Normal Roof |
- |
- |

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
2 |
ROOF ANTENNA ASSEMBLY WITH COVER |
- |
- |
- |
- |
3 |
ROOF ANTENNA ASSEMBLY |
86300J |
- |
- |
- |
*A |
for Normal Roof |
- |
- |
*1 |
COVER |
*2 |
ROOF ANTENNA HOUSING |
● |
Non-reusable part |
- |
- |

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
4 |
ROOF TOP MOULDING SUB-ASSEMBLY |
75607B |
- |
- |
- |
5 |
ROOF ANTENNA ASSEMBLY |
86300J |
- |
- |
- |
*A |
for Panoramic Moon Roof |
- |
- |
*1 |
ROOF ANTENNA HOUSING |
- |
- |
● |
Non-reusable part |
- |
- |
PROCEDURE
1. REMOVE ROOF HEADLINING ASSEMBLY (for Normal Roof)
Click here ![]()
2. REMOVE ROOF ANTENNA ASSEMBLY WITH COVER (for Normal Roof)

![]() |
Remove in this Direction |
- |
- |
3. REMOVE ROOF ANTENNA ASSEMBLY (for Normal Roof)

*A |
When reusing the telephone antenna assembly |
- |
- |
![]() |
Remove in this Direction (1) |
![]() |
Remove in this Direction (2) |
4. REMOVE ROOF TOP MOULDING SUB-ASSEMBLY (for Panoramic Moon Roof)
Click here ![]()
5. REMOVE ROOF ANTENNA ASSEMBLY (for Panoramic Moon Roof)

![]() |
Remove in this Direction |
- |
- |

*A |
When reusing the telephone antenna assembly |
- |
- |
![]() |
Remove in this Direction (1) |
- |
- |
Installation
INSTALLATION
COMPONENTS (INSTALLATION)
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
ROOF ANTENNA ASSEMBLY |
86300J |
- |
- |
- |
2 |
ROOF TOP MOULDING SUB-ASSEMBLY |
75607B |
- |
- |
- |
*A |
for Panoramic Moon Roof |
- |
- |
*1 |
ROOF ANTENNA HOUSING |
- |
- |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
3 |
ROOF ANTENNA ASSEMBLY |
86300J |
- |
- |
- |
4 |
ROOF ANTENNA ASSEMBLY WITH COVER |
- |
- |
- |
- |
*A |
for Normal Roof |
- |
- |
*1 |
COVER |
*2 |
ROOF ANTENNA HOUSING |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
5 |
ROOF HEADLINING ASSEMBLY |
- |
- |
- |
- |
*A |
for Normal Roof |
- |
- |
PROCEDURE
1. INSTALL ROOF ANTENNA ASSEMBLY (for Panoramic Moon Roof)
Torque:
9,5 N·m {97 kgf·cm, 84 in·lbf}
2. INSTALL ROOF TOP MOULDING SUB-ASSEMBLY (for Panoramic Moon Roof)
Click here ![]()
3. INSTALL ROOF ANTENNA ASSEMBLY (for Normal Roof)
4. INSTALL ROOF ANTENNA ASSEMBLY WITH COVER (for Normal Roof)
Torque:
9,5 N·m {97 kgf·cm, 84 in·lbf}
5. INSTALL ROOF HEADLINING ASSEMBLY (for Normal Roof)
Click here
![]()

























