Radio Antenna Cord (for Roof)
- Removal
- Installation
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during antenna cord sub-assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/ReplacedReplaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
| *: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation. | |||
w/ Occupant Classification System:
|
Zero point calibration (Occupant classification system) |
|
|
CAUTION:
Be sure to read Precaution thoroughly before servicing.

Click here ![]()
NOTICE:
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
Click here ![]()
HINT:
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when Toyota Prius vehicle is drivenEffect/Inoperative Function When Necessary Procedures are not Performed | Necessary Procedures | Link |
|---|---|---|
Front Camera System |
Drive the Toyota Prius vehicle straight ahead at 35 km/h or more for 5 seconds or more. |
Effect/Inoperative Function When Necessary Procedures are not Performed | Necessary Procedures | Link |
|---|---|---|
| *1: w/o Power Back Door System *2: w/ Power Back Door System |
||
Power Door Lock Control System*1
|
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. |
|
Power Back Door System*2 |
Reset back door close position |
|
Air Conditioning System |
After the ignition switch is turned to ON, the servo motor standard position is recognized. |
- |

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
ROOF HEADLINING ASSEMBLY |
- |
- |
- |
- |
2 |
NO. 3 ANTENNA CORD SUB-ASSEMBLY |
86101D |
- |
- |
- |

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
3 |
ANTENNA CORD SUB-ASSEMBLY |
86101 |
- |
- |
- |
PROCEDURE
1. REMOVE ROOF HEADLINING ASSEMBLY
Click here ![]()
2. REMOVE NO. 3 ANTENNA CORD SUB-ASSEMBLY
(a) for Normal Roof:

![]() |
Adhesive Tape |
- |
- |
(b) for Panoramic Moon Roof:

![]() |
Adhesive Tape |
- |
- |
3. REMOVE ANTENNA CORD SUB-ASSEMBLY

Installation
INSTALLATION
COMPONENTS (INSTALLATION)
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
ANTENNA CORD SUB-ASSEMBLY |
86101 |
- |
- |
- |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
- |
- |

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
2 |
NO. 3 ANTENNA CORD SUB-ASSEMBLY |
86101D |
- |
- |
|
3 |
ROOF HEADLINING ASSEMBLY |
- |
- |
- |
- |
PROCEDURE
1. INSTALL ANTENNA CORD SUB-ASSEMBLY
Torque:
10 N·m {102 kgf·cm, 7 ft·lbf}
2. INSTALL NO. 3 ANTENNA CORD SUB-ASSEMBLY
(a) for Normal Roof:

*1 |
No. 3 Antenna Cord Sub-assembly |
- |
- |
*a |
Marking Tape (A) |
*b |
Marking Tape (B) |
*c |
Protrusion |
*d |
Marking |
*e |
Correct |
*f |
Incorrect |
*g |
10 mm (0.394 in.) or more |
- |
- |
![]() |
Adhesive Tape |
![]() |
Adjustment Area |
Adhesive Tape Size:
Area | Dimension | Area | Dimension |
|---|---|---|---|
A |
20 mm (0.787 in.) |
B |
80 mm (3.15 in.) or more |
(1) Align the marking tape (A) on the No. 3 antenna cord sub-assembly with the protrusion on the front of the roof headlining assembly and wrap tape around the No. 3 antenna cord sub-assembly and protrusion of the roof headlining assembly.
(2) Align the marking tape (B) on the No. 3 antenna cord sub-assembly with the protrusion on the rear of the roof headlining assembly and wrap tape around the No. 3 antenna cord sub-assembly and protrusion of the roof headlining assembly.
(3) Install the No. 3 antenna cord sub-assembly with adhesive tape.
NOTICE:
- Apply the tape securely in place.
- Do not touch the adhesive surface when applying the tape to prevent adhesion failure.
HINT:
Secure the extra length of the No. 3 antenna cord sub-assembly in the adjustment area.
(b) for Panoramic Moon Roof:

*1 |
No. 3 Antenna Cord Sub-assembly |
- |
- |
*a |
Marking Tape (A) |
*b |
Marking Tape (B) |
*c |
Protrusion |
*d |
Marking |
*e |
Correct |
*f |
Incorrect |
*g |
10 mm (0.394 in.) or more |
- |
- |
![]() |
Adhesive Tape |
![]() |
Adjustment Area |
Adhesive Tape Size:
Area | Dimension | Area | Dimension |
|---|---|---|---|
A |
20 mm (0.787 in.) |
B |
80 mm (3.15 in.) or more |
(1) Align the marking tape (A) on the No. 3 antenna cord sub-assembly with the protrusion on the front of the roof headlining assembly and wrap tape around the No. 3 antenna cord sub-assembly and protrusion of the roof headlining assembly.
(2) Align the marking tape (B) on the No. 3 antenna cord sub-assembly with the protrusion on the rear of the roof headlining assembly and wrap tape around the No. 3 antenna cord sub-assembly and protrusion of the roof headlining assembly.
(3) Install the No. 3 antenna cord sub-assembly with adhesive tape.
NOTICE:
- Apply the tape securely in place.
- Do not touch the adhesive surface when applying the tape to prevent adhesion failure.
HINT:
Secure the extra length of the No. 3 antenna cord sub-assembly in the adjustment area.
3. INSTALL ROOF HEADLINING ASSEMBLY
Click here
![]()























