Steering Column Assembly

In this manual: Steering Column Assembly
How To Troubleshoot Ecu Controlled Systems — 1How To Use This Manual — 1Identification Information — 1Repair Instruction — 1Terms — 12zr-fxe Air Cleaner Filter Element — 12zr-fxe Auxiliary Battery — 12zr-fxe Coolant (for Engine Coolant) — 12zr-fxe Oil And Oil Filter — 12zr-fxe Spark Plug — 1Air Conditioning Filter — 1Battery Cooling Filter — 1Brake Fluid — 1Coolant (for Inverter) — 1Front Brake Flexible Hose — 1Front Disc Brake Pad — 1Front Lower Ball Joint — 1Front Wheel Alignment — 1Front Wiper Rubber — 1General Maintenance — 1M20a-fxs Air Cleaner Filter Element — 1M20a-fxs Auxiliary Battery — 1M20a-fxs Coolant (for Engine Coolant) — 1M20a-fxs Oil And Oil Filter — 1M20a-fxs Spark Plug — 1Pa10/pb10/pb12 Hybrid Transaxle Fluid — 1Q810 Hybrid Transaxle Fluid — 1Rear Brake Flexible Hose — 1Rear Disc Brake Pad — 1Rear Wheel Alignment — 1Steering Column — 1Tire And Wheel — 1Transmitter Battery — 1When Disconnecting Or Reconnecting Battery Terminal — 1When Replacing Or Removing/installing Parts — 1Automatic High Beam Main Switch — 1Automatic High Beam System — 1Driver Monitor Camera — 1Driver Monitor Camera System — 1Driver Monitor Ecu — 1Front Camera — 1Front Camera System — 1Front Radar Sensor System — 1Front Side Radar Sensor — 1Front Side Radar Sensor System — 1Millimeter Wave Radar Sensor — 1Utility — 1Advanced Park — 1Advanced Park Main Switch — 1Amplifier Antenna — 1Audio And Visual System — 1Front Door Speaker — 1Instrument Panel Speaker — 1Microphone — 1Noise Filter — 1Pillar Speaker — 1Radio Antenna Cord (for Back Door) — 1Radio Antenna Cord (for Instrument Panel) — 1Radio Antenna Cord (for Roof) — 1Radio Receiver — 1Rear Door Speaker — 1Roof Antenna — 1Stereo Component Amplifier — 1Stereo Jack Adapter Assembly — 1Window Glass Antenna Wire — 1Back-up Battery — 1Dcm(telematics Transceiver) — 1Manual(sos)switch — 1Safety Connect System — 1Telephone And Gps Antenna (for Front Side) — 1Telephone And Gps Antenna (for Roof Side) — 1Telephone And Gps Antenna Cords — 1Garage Door Opener System (for Digital Inner Mirror) — 1Garage Door Opener System (for Ec Inner Mirror) — 1Blind Spot Monitor Sensor — 1Blind Spot Monitor System — 1Clearance Warning Ecu — 1Intuitive Parking Assist System — 1Panoramic View Monitor Switch — 1Panoramic View Monitor System — 1Parking Assist Ecu — 1Parking Assist Light — 1Parking Assist Monitor System — 1Parking Support Brake System — 1Rear View Monitor System — 1Television Camera (for Front) — 1Television Camera (for Rear) — 1Television Camera (for Side) — 1Ultrasonic Sensor (for Front) — 1Ultrasonic Sensor (for Rear) — 1Brake Actuator — 1Brake Pedal Stroke Sensor — 1Electronically Controlled Brake System — 1Front Speed Sensor — 1Rear Speed Sensor (for Awd) — 1Steering Angle Sensor — 1Brake Booster — 1Brake Fluid — 1Brake Line — 1Brake Pedal — 1Brake System — 1Electric Parking Brake Actuator — 1Electric Parking Brake Switch — 1Electric Parking Brake System — 1Forced Release — 1Front Axle Hub — 1Front Axle Hub Bolt — 1Rear Axle Carrier (for 2wd) — 1Rear Axle Carrier (for Awd) — 1Rear Axle Hub (for 2wd) — 1Rear Axle Hub (for Awd) — 1Rear Axle Hub Bolt — 1Steering Knuckle — 1Drive Shaft System — 1Front Drive Shaft Assembly — 1Rear Drive Shaft Assembly — 1Combination Switch — 1Electronic Shift Lever System — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Oil Seal — 1Hybrid Transaxle System — 1Input Shaft Oil Seal — 1Motor Cable — 1Pa10 Hybrid Vehicle Transaxle — 1Pa10 Manual Parking Lock Release — 1Pa10 Oil Cooler — 1Pb10/pb12 Hybrid Vehicle Transaxle — 1Pb10/pb12 Manual Parking Lock Release — 1Pb10/pb12 Oil Cooler — 1Shift Control Actuator — 1Shift Lever — 1Shift Lever Knob — 1Differential Side Gear Shaft — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Side Gear Oil Seal — 1Motor Cable — 1Rear Traction Motor — 1Coolant (for Engine) — 1Cooling Fan Motor — 1Cooling Fan System — 1Radiator — 1Relay — 1Thermostat — 1Water Pump — 1Canister — 1Egr Cooler — 1Egr Valve — 1Emission Control System — 1Fuel Tank Cap — 1Pcv Valve — 1Purge Valve — 1Vacuum Sensor — 1Air Fuel Ratio Sensor — 1Camshaft Oil Control Valve — 1Camshaft Position Sensor — 1Crankshaft Position Sensor — 1Ecm — 1Engine Coolant Temperature Sensor — 1Heated Oxygen Sensor — 1Ignition Coil And Spark Plug — 1Ignition System — 1Knock Sensor — 1Mass Air Flow Meter — 1Relay — 1Sfi System — 1Throttle Body — 1Camshaft — 1Cylinder Block — 1Cylinder Head — 1Cylinder Head Gasket — 1Engine — 1Engine Assembly — 1Engine Unit — 1Front Crankshaft Oil Seal — 1Rear Crankshaft Oil Seal — 1Fuel Filter — 1Fuel Injector — 1Fuel Pressure Regulator — 1Fuel Pump — 1Fuel Sender Gauge Assembly — 1Fuel System — 1Fuel Tank — 1Air Cleaner Filter Element — 1Exhaust Manifold — 1Exhaust Pipe — 1Intake Manifold — 1Intake System — 1Lubrication System — 1Oil And Oil Filter — 1Oil Pan And Oil Level Sensor — 1Oil Pressure Switch — 1Oil Pump — 1Accelerator Pedal Sensor — 1Battery Blower (for Hev Model) — 1Battery Ecu (for Hev Model) — 1Battery Ecu (for Phev Model) — 1Battery Voltage Sensor (for Phev Model) — 1Charge Cable (for Phev Model) — 1Charge Indicator (for Phev Model) — 1Charge Inlet (for Phev Model) — 1Combination Switch — 1Coolant (for Inverter) — 1Cooler (for Phev Model) — 1Electric Vehicle Charger Assembly (for Phev Model) — 1Frame Wire (for Hev Model) — 1Frame Wire (for Phev Model) — 1Heater Relay (for Phev Model) — 1Hv Battery (for Hev Model) — 1Hv Battery (for Phev Model) — 1Hv Battery Heater (for Phev Model) — 1Hv Battery Stack (for Phev Model) — 1Hv Relay Assembly (for Hev Model) — 1Hv Relay Assembly (for Phev Model) — 1Hybrid Battery System (for 2zr-fxe) — 1Hybrid Battery System (for M20a-fxs) — 1Hybrid Battery System (for Phev Model) — 1Hybrid Vehicle Control Ecu — 1Inverter With Converter (for Hev Model) — 1Motor Generator Control System (for 2zr-fxe) — 1Plug-in Charge Control System (for Phev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Service Plug Grip (for Hev Model) — 1Sub Radiator — 1Water Pump With Motor — 1Auxiliary Battery — 1Battery Current Sensor — 1Charging System — 1Solar Charging System — 1Solar Control Unit — 1Solar Roof — 1Can Communication System (for Hev Model) — 1Lin Communication System — 1Network Gateway Ecu — 1Integration Control Supply — 1Main Body Ecu — 1Power Integration System — 1Sub Battery System — 1Power Steering Ecu — 1Power Steering System — 1Heated Steering Wheel Controller — 1Heated Steering Wheel System — 1Steering Column Assembly — 1Steering Heater Switch — 1Steering Pad Switch — 1Steering System — 1Steering Wheel — 1Front Lower Ball Joint — 1Front Lower Suspension Arm (for 2zr-fxe Lh Side) — 1Front Lower Suspension Arm (for 2zr-fxe Rh Side) — 1Front Lower Suspension Arm (for M20a-fxs) — 1Front Shock Absorber — 1Front Stabilizer Bar — 1Front Suspension Member — 1Rear Coil Spring — 1Rear Lower Arm (for Awd Lh Side) — 1Rear Lower Arm (for Awd Rh Side) — 1Rear Lower Arm (for Hev Model 2wd) — 1Rear Lower Arm (for Phev Model) — 1Rear Shock Absorber — 1Rear Stabilizer Bar — 1Rear Suspension Member (for 2wd) — 1Rear Suspension Member (for Awd) — 1Rear Trailing Arm — 1Rear Upper Arm — 1Tire And Wheel System — 1Tire Repair Seal — 1Tire Pressure Warning Receiver — 1Tire Pressure Warning System — 1Tire Pressure Warning Valve — 1Acoustic Vehicle Alerting System — 1Vehicle Approaching Speaker — 1Vehicle Approaching Speaker Ecu — 1Back Door — 1Back Door Closer Ecu — 1Back Door Opener Switch — 1Back Door Support — 1Back Door Weatherstrip — 1Charge Lid Courtesy Switch — 1Charge Lid Opener Motor Assembly — 1Charge Lid Opener System — 1Charge Lid Opener Unit — 1Front Door — 1Front Door Opening Trim Weatherstrip — 1Fuel Lid Opener Motor Assembly — 1Fuel Lid Opener Switch — 1Fuel Lid Opener System — 1Hood — 1Hood Lock Control Cable Assembly — 1Power Back Door Closer Switch — 1Power Back Door Control Switch — 1Power Back Door Drive Unit — 1Power Back Door System — 1Power Back Door Touch Sensor — 1Power Back Door Warning Buzzer — 1Rear Door — 1Rear Door Opening Trim Weatherstrip — 1Reserve Lock Switch — 1Front Bumper — 1Front Door Belt Moulding — 1Front Door Window Frame Moulding — 1Front Fender — 1Front Pillar Upper Cover — 1Grille Shutter — 1Grille Shutter System — 1Name Plate — 1Quarter Garnish — 1Rear Bumper — 1Rear Door Belt Moulding — 1Rear Door Window Frame Moulding — 1Rear Wheel House Plate — 1Rocker Panel Moulding — 1Roof Drip Side Finish Moulding — 1Roof Garnish — 1Wheel Opening Moulding (for Front Side) — 1Wheel Opening Moulding (for Rear Side) — 1Windshield Outside Moulding — 1Horn — 1Horn System — 1Relay — 1Automatic Light Control Sensor — 1Back-up Light Assembly — 1Charge Lid Light — 1Front Marker Light — 1Hazard Warning Switch — 1Headlight Assembly — 1Headlight Dimmer Switch — 1Headlight Leveling Switch — 1High Mounted Stop Light Assembly — 1Illumination Light Assembly — 1License Plate Light Assembly — 1Lighting System — 1Rear Combination Light Assembly — 1Rear Light Assembly — 1Rear Side Marker Light Assembly — 1Relay — 1Side Turn Signal Light Assembly — 1Stop Light Switch — 1Switch Housing — 1Outer Mirror Switch — 1Outer Rear View Mirror — 1Outer Rear View Mirror Cover — 1Outer Rear View Mirror Glass — 1Power Mirror Control System — 1Back Door Glass — 1Front Passenger Side Power Window Switch — 1Power Window Control System — 1Power Window Master Switch — 1Power Window Regulator Motor (for Front Door) — 1Power Window Regulator Motor (for Rear Door) — 1Rear Power Window Switch — 1Relay — 1Roof Window Fix Glass — 1Window Defogger System — 1Windshield Deicer Switch — 1Windshield Deicer System — 1Windshield Glass — 1Front Wiper Motor — 1Rain Sensor — 1Relay — 1Washer Motor — 1Washer Nozzle (for Front Side) — 1Washer Nozzle (for Rear Television Camera) — 1Wiper And Washer System — 1Wiper Ecu — 1Wiper Switch — 1Back Door Lock — 1Door Control Receiver — 1Door Control Switch — 1Door Control Transmitter — 1Door Lock Release Motor (for Rear Side) — 1Door Outside Handle (for Rear Side) — 1Front Door Lock — 1Power Door Lock Control System — 1Rear Door Lock — 1Transmitter Battery — 1Wireless Door Lock Control System — 1Accumulator — 1Air Conditioning Amplifier — 1Air Conditioning Panel — 1Air Conditioning Pressure Sensor — 1Air Conditioning Unit — 1Ambient Temperature Sensor — 1Blower Unit — 1Condenser (for Hev Model) — 1Condenser (for Phev Model) — 1Discharge Temperature Sensor — 1Electric Expansion Valve (cooling) — 1Electric Expansion Valve (heating) — 1Evaporator Pipe Temperature Sensor — 1Evaporator Pressure Regulator — 1Front Blower Motor — 1Front Evaporator Front Solenoid Valve — 1Air Conditioning System (for Hev Model) — 1Front Evaporator Temperature Sensor — 1Heat Exchanger Temperature Sensor — 1Heat Pump Ecu — 1High Pressure Magnetic Valve — 1Humidity Sensor — 1Internal Condenser Temperature Sensor — 1Low Pressure Magnetic Valve — 1Refrigerant (for Hfc-134a(r134a)) — 1Refrigerant Line (for Hev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Room Temperature Sensor — 1Solar Sensor — 1Floor Carpet — 1Front Console Box — 1Instrument Panel Safety Pad — 1Roof Headlining — 1Roof Sunshade — 1Ambient Light (for Driver Side) — 1Ambient Light (for Front Passenger Side) — 1Back Door Courtesy Switch — 1Footwell Light — 1Glove Box Light — 1Lighting System — 1Luggage Compartment Room Light — 1Personal Light — 1Room Light — 1Vanity Light — 1Vanity Light Switch — 1Combination Meter — 1Meter / Gauge System — 1Trip Switch — 1Digital Inner Mirror — 1Digital Rear-view Mirror System — 1Inner Mirror Monitor Camera — 1Inner Rear View Mirror (w/o Ec Mirror) — 1Accessory Power Outlet System — 1Power Outlet Socket (for Console Box Front Side) — 1Power Outlet Socket (for Console Box Rear Side) — 1Power Outlet Socket (for Console Box) — 1Power Outlet Socket (for Luggage Compartment) — 1Power Outlet Switch — 1Wireless Charger Assembly — 1Wireless Charging System — 1Climate Control Seat System — 1Front Power Seat Control System (w/ Memory) — 1Front Power Seat Motor Assembly — 1Front Seat Assembly (for Power Seat) — 1Front Seat Cushion Heater (for Power Seat) — 1Front Seatback Heater (for Power Seat) — 1Lumbar Support Adjuster Assembly — 1Power Seat Control Ecu — 1Power Seat Switch — 1Power Seat Track Rail Assembly — 1Rear Seat Assembly — 1Rear Seat Cushion Heater — 1Rear Seat Reminder System — 1Rear Seatback Heater — 1Seat Heater Control — 1Seat Heater Switch (for Front Seat) — 1Seat Heater Switch (for Rear Side) — 1Seat Heater System — 1Seat Memory Switch — 1Child Restraint Seat Anchor Bracket — 1Front Seat Inner Belt Assembly — 1Front Seat Outer Belt Assembly — 1Occupant Detection Sensor (for Front Passenger Side) — 1Rear Center Seat Outer Belt Assembly — 1Rear Seat Inner Belt Assembly (for Rh Side) — 1Rear Seat Outer Belt Assembly — 1Seat Belt Warning System (w/ Occupant Classification System) — 1Tongue Plate Stopper — 1Airbag System — 1Center Airbag Sensor Assembly — 1Curtain Shield Airbag Assembly — 1Front Airbag Sensor — 1Front Passenger Airbag Assembly — 1Front Seat Side Airbag Assembly — 1Inspection After Collision — 1Knee Airbag Assembly — 1Occupant Classification System — 1Rear Seat Side Airbag Assembly — 1Side Airbag Sensor (for Center Pillar) — 1Side Airbag Sensor (for Front Door) — 1Spiral Cable — 1Steering Pad — 1Certification Ecu — 1Digital Key Ecu — 1Digital Key Receiver (for Front Floor) — 1Digital Key Receiver (for Outside Luggage Compartment) — 1Digital Key Receiver (for Rear Door) — 1Digital Key System — 1Electrical Key Oscillator (for Front Floor) — 1Electrical Key Oscillator (for Outside Luggage Compartment) — 1Electrical Key Oscillator (for Rear Floor) — 1Engine Hood Courtesy Switch — 1Id Code Box — 1Smart Key System (for Start Function) — 1
~15min read
0204060801006447N·mlb·ft
Tightening torque found on this page
  • Removal
  • Disassembly
  • Inspection
  • Reassembly
  • Installation

Removal

REMOVAL

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during steering column assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replacement Part or Procedure

Necessary Procedures

Effect/Inoperative Function When Necessary Procedures are not Performed

Link

*1: If matchmarks were not placed when removing parts related to steering operation, perform end position initial setting.

Power steering ECU assembly

Update ECU security key

Toyota Prius Vehicle Control History (RoB) are stored

ECU configuration

  • Vehicle Control History (RoB) are stored
  • EPS warning light illuminates

Perform power steering ECU initial setting (torque sensor zero point calibration and assist map writing)

  • Toyota Prius Vehicle Control History (RoB) are stored
  • EPS warning light illuminates

End position initial setting

-

Electric power steering column sub-assembly

Perform power steering ECU initial setting (torque sensor zero point calibration and assist map writing)

  • Toyota Prius Vehicle Control History (RoB) are stored
  • EPS warning light illuminates

End position initial setting

-

No. 2 steering intermediate shaft assembly*1

End position initial setting

-

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

Learning completes when Toyota Prius vehicle is driven

Effect/Inoperative Function when Necessary Procedure not Performed

Necessary Procedure

Link

Front Camera System

Drive the Toyota Prius vehicle straight ahead at 35 km/h or more for 5 seconds or more.

Learning completes when vehicle is operated normally

Effect/Inoperative Function when Necessary Procedure not Performed

Necessary Procedure

Link

*1: w/o Power Back Door System

*2: w/ Power Back Door System

Power Door Lock Control System*1

  • Back door opener

Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.

Power Back Door System*2

Reset back door close position

Air Conditioning System

for HEV Model:
  • After the ignition switch is turned to ON, the servo motor standard position is recognized.
for PHEV Model:
  • After the ignition switch is turned to ON, the servo motor and cooler expansion valve standard position is recognized.

-

HINT:

  • Release the tilt and telescopic lever and fully extend and lower the steering column assembly.
  • Lock the tilt and telescopic lever.
COMPONENTS (REMOVAL)

Procedure

Part Name Code

1

PRECAUTION

-

-

-

2

ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

-

-

-

3

STEERING WHEEL ASSEMBLY

45100

-

-

-

Procedure

Part Name Code

4

LOWER STEERING COLUMN COVER

45287

-

-

5

UPPER STEERING COLUMN COVER

45286B

-

-

6

TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

-

-

-

*A

w/o Driver Monitor Camera

*B

w/ Driver Monitor Camera

Procedure

Part Name Code

7

FRONT DOOR SCUFF PLATE LH

67914

-

-

-

8

COWL SIDE TRIM BOARD LH

62112

-

-

-

9

NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

55606

-

-

-

10

LOWER CENTER INSTRUMENT PANEL FINISH PANEL

55434B

-

-

-

11

LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

55480D

-

-

-

12

LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

73900

-

-

13

NO. 2 KNEE PROTECTOR BRACKET

55462C

-

-

-

14

FRONT NO. 1 CONSOLE BOX INSERT

58816D

-

-

-

*A

w/ Knee Airbag

*B

w/o Knee Airbag

Procedure

Part Name Code

15

NO. 1 AIR DUCT

87211

-

-

●

Non-reusable part

-

-

Procedure

Part Name Code

16

COLUMN HOLE COVER SILENCER SHEET

45259A

-

-

-

17

SEPARATE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

45260

-

-

-

18

REMOVE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

45260

-

-

-

19

STEERING COLUMN ASSEMBLY

-

-

-

PROCEDURE

1. PRECAUTION

Click here

2. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

3. REMOVE STEERING WHEEL ASSEMBLY

Click here

4. REMOVE LOWER STEERING COLUMN COVER

NOTICE:

Removing the lower steering column cover in the incorrect order will cause the parts to break.

Push Area

Operate in this direction

Push in this direction

-

-

(1) Release the tilt and telescopic lever and fully extend and lower the steering column assembly.

(2) Lock the tilt and telescopic lever.

(3) Remove the 3 screws.

(4) While pressing the push area shown in the illustration to disengage the 2 claws, slightly lower the lower steering column cover.

5. REMOVE UPPER STEERING COLUMN COVER

w/ Driver Monitor Camera:

NOTICE:

As there is a possibility of the upper steering column cover cracking, do not apply oil, grease, etc., at the position shown in the illustration.

(a) w/o Driver Monitor Camera:

(b) w/ Driver Monitor Camera:

6. REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

NOTICE:

  • Do not remove/install the spiral cable with sensor sub-assembly with the auxiliary battery connected and the ignition switch ON.
  • Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the auxiliary battery connected and the ignition switch ON.
  • Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.

HINT:

As the illustration shown is an example, the actual details may differ.

*a

Clamp

-

-

(1) Disconnect each connector from the turn signal switch assembly with spiral cable sub-assembly.

(2) Using pliers, expand the clamp.

(3) While holding the clamp expanded, raise the claw using a screwdriver to disengage it, and then remove the turn signal switch assembly with spiral cable sub-assembly from the steering column assembly.

7. REMOVE FRONT DOOR SCUFF PLATE LH

Click here

8. REMOVE COWL SIDE TRIM BOARD LH

Click here

9. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Click here

10. REMOVE LOWER CENTER INSTRUMENT PANEL FINISH PANEL

Click here

11. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

Click here

12. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Knee Airbag)

Click here

13. REMOVE NO. 2 KNEE PROTECTOR BRACKET (w/o Knee Airbag)

14. REMOVE FRONT NO. 1 CONSOLE BOX INSERT

Click here

15. REMOVE NO. 1 AIR DUCT

NOTICE:

Be careful not to deform or damage the lower heater case of the air conditioner unit assembly when removing the No. 1 air duct.

*a

View A

-

-

Front

-

-

16. REMOVE COLUMN HOLE COVER SILENCER SHEET

Open in this direction

Place Hand Here

17. SEPARATE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

*a

Matchmark

-

-

Separate in this direction

-

-

(1) Put matchmarks on the No. 2 steering intermediate shaft assembly and steering gear assembly.

(2) Remove the bolt.

(3) Separate the No. 2 steering intermediate shaft assembly from the steering gear assembly.

18. REMOVE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

*a

Matchmark

-

-

Remove in this direction

-

-

(1) Put matchmarks on the No. 2 steering intermediate shaft assembly and steering column assembly.

(2) Remove the bolt.

(3) Remove the No. 2 steering intermediate shaft assembly from the steering column assembly.

19. REMOVE STEERING COLUMN ASSEMBLY

HINT:

As the illustration shown is an example, the actual details may differ.

(1) Disconnect each connector and disengage each wire harness clamp from the steering column assembly.

(2) Remove the bolt, 2 nuts and steering column assembly.

Disassembly

DISASSEMBLY

NOTICE:

  • Do not drop the power steering ECU assembly, strike it with tools or subject it to impacts.
  • If the power steering ECU assembly is subjected to an impact, replace it with a new one.
  • Do not pull the wire harness.
  • Do not allow any moisture to come into contact with the power steering ECU assembly.
  • Do not loosen any bolts not mentioned in the procedure.
  • Do not allow any foreign matter to contaminate the power steering ECU assembly.
COMPONENTS (DISASSEMBLY)

Procedure

Part Name Code

1

POWER STEERING ECU ASSEMBLY

89650

-

-

2

ELECTRIC POWER STEERING MOTOR SHAFT DAMPER

45254B

-

-

-

*1

ELECTRIC POWER STEERING COLUMN SUB-ASSEMBLY

-

-

●

Non-reusable part

-

-

PROCEDURE

1. REMOVE POWER STEERING ECU ASSEMBLY

Click here

2. REMOVE ELECTRIC POWER STEERING MOTOR SHAFT DAMPER

Click here

Inspection

INSPECTION

PROCEDURE

1. INSPECT PRELOAD

(a) Using a 10 mm hexagon socket wrench, install the steering wheel assembly set bolt to the steering main shaft.

NOTICE:

  • Do not apply excessive torque to the steering wheel assembly set bolt by using a tool such as an impact wrench.
  • The steering wheel assembly set bolt is used for turning the steering main shaft during inspection of the steering main shaft rotating torque.
  • Remove the steering wheel assembly set bolt after performing this inspection.

(b) Secure the steering column assembly in a vise using aluminum plates, cloths and wooden blocks.

NOTICE:

  • Do not overtighten the vise, as the steering column assembly may become deformed.
  • Support the steering column assembly with wooden blocks or similar items to ensure that it does not fall.

*a

Wooden Block

*b

Cloth

(c) Using a torque wrench, turn the steering main shaft at a constant rate of approximately 1 revolution every 4 seconds and measure the preload.

Preload

Specified Condition

Result

1.0 to 2.3 N*m

11 to 23 kgf*cm

9 to 20 in.*lbf

N*m

kgf*cm

in.*lbf

(d) If the preload is not as specified, replace the power steering ECU assembly or electric power steering column sub-assembly with a new one.

(e) Remove the steering wheel assembly set bolt.

2. INSPECT STEERING COLUMN ASSEMBLY

(a) Check that the 2 bushings are securely installed to the steering column assembly.

(b) If the bushings are deformed, missing or damaged, replace the electric power steering column sub-assembly with a new one.

Reassembly

REASSEMBLY

NOTICE:

  • Do not drop the power steering ECU assembly, strike it with tools or subject it to impacts.
  • If the power steering ECU assembly is subjected to an impact, replace it with a new one.
  • Do not pull the wire harness.
  • Do not allow any moisture to come into contact with the power steering ECU assembly.
  • Do not loosen any bolts not mentioned in the procedure.
  • Do not allow any foreign matter to contaminate the power steering ECU assembly.
COMPONENTS (REASSEMBLY)

Procedure

Part Name Code

1

ELECTRIC POWER STEERING MOTOR SHAFT DAMPER

45254B

-

-

2

POWER STEERING ECU ASSEMBLY

89650

-

-

*1

ELECTRIC POWER STEERING COLUMN SUB-ASSEMBLY

-

-

Tightening torque for "Major areas involving basic Toyota Prius vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf)

●

Non-reusable part

Grease

-

-

PROCEDURE

1. INSTALL ELECTRIC POWER STEERING MOTOR SHAFT DAMPER

Click here

2. INSTALL POWER STEERING ECU ASSEMBLY

Click here

Installation

INSTALLATION

COMPONENTS (INSTALLATION)

Procedure

Part Name Code

1

ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

-

-

-

2

STEERING COLUMN ASSEMBLY

-

-

-

3

INSTALL NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

45260

-

-

4

CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

45260

-

-

5

COLUMN HOLE COVER SILENCER SHEET

45259A

-

-

-

Tightening torque for "Major areas involving basic Toyota Prius vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf)

-

-

Procedure

Part Name Code

6

NO. 1 AIR DUCT

87211

-

-

-

●

Non-reusable part

-

-

N*m (kgf*cm, ft.*lbf): Specified torque

-

-

Procedure

Part Name Code

7

FRONT NO. 1 CONSOLE BOX INSERT

58816D

-

-

-

8

NO. 2 KNEE PROTECTOR BRACKET

55462C

-

-

-

9

LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

73900

-

-

10

LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

55480D

-

-

-

11

LOWER CENTER INSTRUMENT PANEL FINISH PANEL

55434B

-

-

-

12

NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

55606

-

-

-

13

COWL SIDE TRIM BOARD LH

62112

-

-

-

14

FRONT DOOR SCUFF PLATE LH

67914

-

-

-

*A

w/ Knee Airbag

*B

w/o Knee Airbag

Tightening torque for "Major areas involving basic Toyota Prius vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf)

N*m (kgf*cm, ft.*lbf): Specified torque

Procedure

Part Name Code

15

TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

-

-

-

16

UPPER STEERING COLUMN COVER

45286B

-

-

17

LOWER STEERING COLUMN COVER

45287

-

-

-

*A

w/o Driver Monitor Camera

*B

w/ Driver Monitor Camera

Procedure

Part Name Code

18

ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

-

-

-

19

INSPECT AND ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

-

-

-

20

STEERING WHEEL ASSEMBLY

45100

-

-

-

21

UPDATE ECU SECURITY KEY

-

-

-

22

ECU CONFIGURATION

-

-

-

23

POWER STEERING ECU INITIAL SETTING (TORQUE SENSOR ZERO POINT CALIBRATION AND ASSIST MAP WRITING)

-

-

-

24

END POSITION INITIAL SETTING

-

-

-

PROCEDURE

1. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

2. INSTALL STEERING COLUMN ASSEMBLY

NOTICE:

Make sure that the wire harness is not interfering with the steering column assembly.

HINT:

As the illustration shown is an example, the actual details may differ.

(1) Install the steering column assembly with the bolt and 2 nuts.

Torque:

36 N*m (367 kgf*cm, 27 ft.*lbf)

NOTICE:

After temporarily tightening the bolt, fully tighten the 2 nuts then fully tighten the bolt.

(2) Connect each connector and engage each wire harness clamp to the steering column assembly.

3. INSTALL NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

*a

Matchmark

-

-

Install in this direction

-

-

(1) Align the matchmarks on the No. 2 steering intermediate shaft assembly and steering column assembly.

(2) Install the No. 2 steering intermediate shaft assembly to the steering column assembly.

(3) Install the bolt.

Torque:

64 N·m {653 kgf·cm, 47 ft·lbf}

4. CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

*a

Matchmark

-

-

Connect in this direction

-

-

(1) Align the matchmarks on the No. 2 steering intermediate shaft assembly and steering gear assembly.

(2) Connect the No. 2 steering intermediate shaft assembly to the steering gear assembly.

(3) Install the bolt.

Torque:

64 N·m {653 kgf·cm, 47 ft·lbf}

5. INSTALL COLUMN HOLE COVER SILENCER SHEET

6. INSTALL NO. 1 AIR DUCT

Torque:

9,8 N·m {100 kgf·cm, 87 in·lbf}

7. INSTALL FRONT NO. 1 CONSOLE BOX INSERT

8. INSTALL NO. 2 KNEE PROTECTOR BRACKET (w/o Knee Airbag)

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

9. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Knee Airbag)

Click here

10. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

Click here

11. INSTALL LOWER CENTER INSTRUMENT PANEL FINISH PANEL

12. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

13. INSTALL COWL SIDE TRIM BOARD LH

14. INSTALL FRONT DOOR SCUFF PLATE LH

15. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

NOTICE:

  • Do not remove/install the spiral cable with sensor sub-assembly with the auxiliary battery connected and the ignition switch ON.
  • Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the auxiliary battery connected and the ignition switch ON.
  • Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.

HINT:

As the illustration shown is an example, the actual details may differ.

*a

Clamp

-

-

(1) Using pliers, expand the clamp.

(2) While holding the clamp expanded, install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly and engage the claw.

(3) Return the clamp to its original position.

(4) Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.

16. INSTALL UPPER STEERING COLUMN COVER

w/ Driver Monitor Camera:

NOTICE:

As there is a possibility of the upper steering column cover cracking, do not apply oil, grease, etc., at the position shown in the illustration.

17. INSTALL LOWER STEERING COLUMN COVER

18. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

19. INSPECT AND ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

Click here

20. INSTALL STEERING WHEEL ASSEMBLY

Click here

21. UPDATE ECU SECURITY KEY

Click here

HINT:

After replacing the power steering ECU assembly, make sure to perform update ECU security key.

22. ECU CONFIGURATION

Click here

HINT:

After replacing the power steering ECU assembly, make sure to perform ECU configuration.

23. PERFORM POWER STEERING ECU INITIAL SETTING (TORQUE SENSOR ZERO POINT CALIBRATION AND ASSIST MAP WRITING)

Click here

24. PERFORM END POSITION INITIAL SETTING

Click here