Motor Cable
- Removal
- Installation
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during motor cable removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/ReplacedReplaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
for 2ZR-FXE:
|
Update ECU security key |
Toyota Prius Vehicle Control History (RoB) are stored |
|
ECU configuration |
- |
||
Perform Toyota Prius Vehicle Identification Number (VIN) registration |
DTC is output |
||
for M20A-FXS:
|
Update ECU security key |
Toyota Prius Vehicle Control History (RoB) are stored |
|
ECU configuration |
- |
||
Perform Toyota Prius Vehicle Identification Number (VIN) registration |
DTC is output |
||
Replacement of inverter with converter assembly |
ECU configuration |
- |
|
Resolver learning |
|
2ZR-FXE: for M20A-FXS HEV model: for M20A-FXS PHEV Model: |
|
for PHEV Model:
|
High voltage fuse accumulated load history reset |
DTCs are stored |
CAUTION:
- Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.
- 2ZR-FXE:
Click here

- for M20A-FXS HEV Model:
Click here

- for M20A-FXS PHEV Model:
Click here

- 2ZR-FXE:
- To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.

HINT:
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when Toyota Prius vehicle is drivenEffect/Inoperative Function when Necessary Procedure not Performed | Necessary Procedure | Link |
|---|---|---|
Front Camera System |
Drive the Toyota Prius vehicle straight ahead at 35 km/h or more for 5 seconds or more. |
Effect/Inoperative Function when Necessary Procedure not Performed | Necessary Procedure | Link |
|---|---|---|
| *1: w/o Power Back Door System *2: w/ Power Back Door System |
||
Power Door Lock Control System*1
|
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. |
|
Power Back Door System*2 |
Reset back door close position |
|
Air Conditioning System |
for HEV Model:
|
- |

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
INVERTER WITH CONVERTER ASSEMBLY |
G9200 |
- |
- |
- |
2 |
TERMINAL CAP |
82823M |
- |
- |
|
3 |
MOTOR CABLE |
G1148 |
- |
- |
|
PROCEDURE
1. REMOVE INVERTER WITH CONVERTER ASSEMBLY
- for HEV Model: Click here

- for PHEV Model: Click here

2. REMOVE TERMINAL CAP
![]() |
CAUTION: Be sure to wear insulated gloves. NOTICE:
|

*a |
Waterproof Seal |
- |
- |
3. REMOVE MOTOR CABLE
![]() |
CAUTION: Be sure to wear insulated gloves. NOTICE:
|

*a |
Waterproof Seal |
- |
- |
(1) Using an insulated tool, remove the 6 bolts and motor cable from the hybrid Toyota Prius vehicle transaxle assembly.
Installation
INSTALLATION
COMPONENTS (INSTALLATION)
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
MOTOR CABLE |
G1148 |
- |
- |
|
2 |
TERMINAL CAP |
82823M |
- |
- |
|
3 |
INVERTER WITH CONVERTER ASSEMBLY |
G9200 |
- |
- |
- |
![]() |
Tightening torque for "Major areas involving basic Toyota Prius vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
PROCEDURE
1. INSTALL MOTOR CABLE
![]() |
CAUTION: Be sure to wear insulated gloves. NOTICE:
|

*a |
Waterproof Seal |
- |
- |
(1) Using an insulated tool, install the motor cable to the hybrid Toyota Prius vehicle transaxle assembly with the 6 bolts.
Torque:
10 N·m {102 kgf·cm, 7 ft·lbf}
2. INSTALL TERMINAL CAP
![]() |
CAUTION: Be sure to wear insulated gloves. NOTICE:
|

*a |
Waterproof Seal |
- |
- |
(1) Temporarily install the terminal cap to the hybrid Toyota Prius vehicle transaxle assembly with the 2 bolts.
(2) Tighten the 2 bolts to install the terminal cap.
Torque:
10 N·m {102 kgf·cm, 7 ft·lbf}
3. INSTALL INVERTER WITH CONVERTER ASSEMBLY
- for HEV Model: Click here

- for PHEV Model: Click here



























