Back Door Glass
- Removal
- Installation
Removal
REMOVAL
NOTICE:
- After cutting off the old adhesive remaining on the adhesion surface, apply new adhesive within 2 hours.
- If the cut surface of the old adhesive is left exposed for a long time, the adhesion strength will be reduced, so apply the new adhesive quickly.

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
BACK DOOR TRIM UPPER PANEL ASSEMBLY |
64790B |
- |
- |
- |
2 |
BACK DOOR SIDE GARNISH LH |
67938A |
- |
- |
- |
3 |
BACK DOOR SIDE GARNISH RH |
67937B |
- |
- |
- |
4 |
BACK DOOR TRIM BOARD ASSEMBLY |
67750 |
- |
- |
- |
5 |
BACK DOOR OUTSIDE GARNISH LOWER MOULDING LH |
76816 |
- |
- |
- |
6 |
BACK DOOR OUTSIDE GARNISH LOWER MOULDING RH |
76815 |
- |
- |
- |
7 |
REAR LIGHT ASSEMBLY |
- |
- |
- |
|

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
8 |
BACK DOOR GLASS |
68131 |
- |
- |
|
9 |
BACK DOOR WINDOW MOULDIMG |
75571F |
- |
- |
|
10 |
NO. 1 BACK WINDOW GLASS SPACER |
64818C |
- |
- |
|
11 |
NO. 2 BACK WINDOW GLASS SPACER |
64819B |
- |
- |
|
12 |
BACK DOOR GLASS SPACER |
62785F |
- |
- |
|
13 |
BACK DOOR GLASS ADHESIVE DAM |
68294A |
- |
- |
|
● |
Non-reusable part |
- |
- |
PROCEDURE
1. REMOVE BACK DOOR TRIM UPPER PANEL ASSEMBLY
Click here ![]()
2. REMOVE BACK DOOR SIDE GARNISH LH
Click here ![]()
3. REMOVE BACK DOOR SIDE GARNISH RH
(a) Use the same procedure as for the LH side.
4. REMOVE BACK DOOR TRIM BOARD ASSEMBLY
Click here ![]()
5. REMOVE BACK DOOR OUTSIDE GARNISH LOWER MOULDING LH
Click here ![]()
6. REMOVE BACK DOOR OUTSIDE GARNISH LOWER MOULDING RH
(a) Use the same procedure as for the LH side.
7. REMOVE REAR LIGHT ASSEMBLY
![]() |
Click here |
8. REMOVE BACK DOOR GLASS
NOTICE:
- After cutting off the old adhesive remaining on the adhesion surface, apply new adhesive within 2 hours.
- If the cut surface of the old adhesive is left exposed for a long time, the adhesion strength will be reduced, so apply the new adhesive quickly.

*a |
Protective Tape |
- |
- |
(1) Apply protective tape to the area around the installation position of the back door glass on the back door panel to prevent it from being scratched.

*a |
Matchmark |
- |
- |
(1) Place matchmarks on the back door glass and Toyota Prius vehicle body at the locations indicated in the illustration.
HINT:
Matchmarks are not necessary if the back door glass is not going to be reused.

(1) Disconnect the 2 connectors.

(1) Disconnect the connector.

*a |
Suction Cup |
- |
- |
(1) Install the 2 suction cups to the back door glass.

*1 |
Back Door Glass |
- |
- |
*a |
Windshield Knife |
*b |
Adhesive |
![]() |
Pull |
- |
- |
(1) When using a windshield knife:
- Apply soapy water to the area around the adhesive.
- Insert a windshield knife into the adhesive between the back door glass and Toyota Prius vehicle body.
- While keeping the windshield knife perpendicular to the outer surface of the back door glass, cut the adhesive by pulling the windshield knife around the back door glass.
NOTICE:
- Do not pry the back door glass with the windshield knife.
- Do not use a windshield knife to cut the adhesive on the lower side of the back door glass.
- When separating the back door glass, be careful not to damage the paint or interior and exterior ornaments.
HINT:
Insert the windshield knife in an area where the gap between back door glass and Toyota Prius vehicle body is large.

*1 |
No. 1 Back Window Glass Spacer |
*2 |
No. 2 Back Window Glass Spacer |
*a |
Piano Wire |
- |
- |
(1) When using piano wire:
- Pass a piano wire between the Toyota Prius vehicle body and glass from the interior, as shown in the illustration.
- Tie both wire ends to wooden blocks or similar objects that can serve as handles.
- Cut the adhesive by pulling the piano wire around the back door glass.
NOTICE:
- When separating the back door glass, be careful not to damage the paint or interior and exterior ornaments.
- To prevent the safety pad from being scratched when removing the back door glass, place a plastic sheet between the piano wire and safety pad.

(1) Using suction cups, disengage the No. 1 back window glass spacer and No. 2 back window glass spacer and remove the back door glass.
NOTICE:
- To prevent the back door glass from falling when performing this operation, be sure to hold the back door glass using suction cups.
- Be careful not to drop the back door glass.
- Leave as much adhesive on the back door panel as possible when removing the back door glass.
9. REMOVE BACK DOOR WINDOW MOULDIMG
(a) When reusing the back door glass:
(1) Using a scraper, remove the back door window moulding.

*a |
Back Side |
- |
- |
NOTICE:
- Be careful not to damage the back door glass.
- Be sure to replace the back door window moulding with a new one.
10. REMOVE NO. 1 BACK WINDOW GLASS SPACER
(a) When reusing the back door glass:

*a |
Back Side |
- |
- |
![]() |
Adhesive Tape |
- |
- |
(1) Apply adhesive tape to the area around the installation position of the No. 1 back window glass spacer on the back door glass.
(2) Using a scraper, remove the No. 1 back window glass spacer.
NOTICE:
- Be careful not to damage the back door glass.
- Be sure to replace the No. 1 back window glass spacer with a new one.
11. REMOVE NO. 2 BACK WINDOW GLASS SPACER
(a) Use the same procedure as for the No. 1 back window glass spacer.
12. REMOVE BACK DOOR GLASS SPACER
(a) When reusing the back door glass:

*a |
Back Side |
- |
- |
(1) Using a scraper, remove the 2 back door glass spacers.
NOTICE:
- Be careful not to damage the back door glass.
- Be sure to replace each back door glass spacer with a new one.
13. REMOVE BACK DOOR GLASS ADHESIVE DAM
(a) When reusing the back door glass:

*a |
Back Side |
- |
- |
(1) Using a scraper, remove the back window glass adhesive dam.
NOTICE:
- Be careful not to damage the back door glass.
- Be sure to replace the back window glass adhesive dam with a new one.
Installation
INSTALLATION
NOTICE:
- Make sure to use Toyota Genuine Windshield Glass Adhesive (High Modulus Type) or an equivalent high modulus adhesive.
- After cutting off the old adhesive remaining on the adhesion surface, apply new adhesive within 2 hours.
- If the cut surface of the old adhesive is left exposed for a long time, the adhesion strength will be reduced, so apply the new adhesive quickly.

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
BACK DOOR GLASS ADHESIVE DAM |
68294A |
- |
- |
|
2 |
BACK DOOR GLASS SPACER |
62785F |
- |
- |
|
3 |
NO. 1 BACK WINDOW GLASS SPACER |
64818C |
- |
- |
|
4 |
NO. 2 BACK WINDOW GLASS SPACER |
64819B |
- |
- |
|
5 |
BACK DOOR WINDOW MOULDIMG |
75571F |
- |
- |
|
6 |
BACK DOOR GLASS |
68131 |
- |
- |
|
● |
Non-reusable part |
- |
- |

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
7 |
REAR LIGHT ASSEMBLY |
- |
- |
- |
|
8 |
BACK DOOR OUTSIDE GARNISH LOWER MOULDING LH |
76816 |
- |
- |
- |
9 |
BACK DOOR OUTSIDE GARNISH LOWER MOULDING RH |
76815 |
- |
- |
- |
10 |
BACK DOOR TRIM BOARD ASSEMBLY |
67750 |
- |
- |
- |
11 |
BACK DOOR SIDE GARNISH RH |
67937B |
- |
- |
- |
12 |
BACK DOOR SIDE GARNISH LH |
67938A |
- |
- |
- |
13 |
BACK DOOR TRIM UPPER PANEL ASSEMBLY |
64790B |
- |
- |
- |
14 |
INSPECT FOR LEAK AND REPAIR |
- |
- |
- |
|
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
- |
- |
PROCEDURE
1. INSTALL BACK DOOR GLASS ADHESIVE DAM
(a) When reusing the back door glass:

*a |
Back Side |
*b |
Marking |
(1) Using a brush or sponge, coat the installation area of the new back window glass adhesive dam with glass primer.
NOTICE:
- Do not apply too much glass primer.
- Allow the glass primer to dry for 3 minutes or more.
- Throw away any leftover glass primer.
HINT:
If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.
(2) Install the back window glass adhesive dam to the back window glass as shown in the illustration.
2. INSTALL BACK DOOR GLASS SPACER
(a) When reusing the back door glass:

*a |
Back Side |
*b |
Marking |
(1) Using a brush or sponge, coat the installation area of 2 new back door glass spacers with glass primer.
NOTICE:
- Do not apply too much glass primer.
- Allow the glass primer to dry for 3 minutes or more.
- Throw away any leftover glass primer.
HINT:
If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.
(2) Install the 2 back door glass spacers to the back door glass as shown in the illustration.
3. INSTALL NO. 1 BACK WINDOW GLASS SPACER

*a |
Back Side |
- |
- |
(1) Using a brush or sponge, coat the installation area of the new No. 1 back window glass spacer with glass primer.
NOTICE:
- Do not apply too much glass primer.
- Allow the glass primer to dry for 3 minutes or more.
- Throw away any leftover glass primer.
HINT:
If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.
(2) Install the No. 1 back window glass spacer to the back door glass as shown in the illustration.
4. INSTALL NO. 2 BACK WINDOW GLASS SPACER
(a) Use the same procedure as for the No. 1 back window glass spacer.
5. INSTALL BACK DOOR WINDOW MOULDIMG
(a) When reusing the back door glass:

*a |
Back Side |
- |
- |
Standard Dimension:
Area | Dimension | Area | Dimension |
|---|---|---|---|
a |
7.3 mm (0.287 in.) |
- |
- |
(1) Using a brush or sponge, coat the installation area of the new back door window moulding with glass primer.
NOTICE:
- Do not apply too much glass primer.
- Allow the glass primer to dry for 3 minutes or more.
- Throw away any leftover glass primer.
HINT:
If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.
(2) Install the back door window moulding to the back door glass as shown in the illustration.
6. INSTALL BACK DOOR GLASS
NOTICE:
- After cutting off the old adhesive remaining on the adhesion surface, apply new adhesive within 2 hours.
- If the cut surface of the old adhesive is left exposed for a long time, the adhesion strength will be reduced, so apply the new adhesive quickly.

*a |
Matchmark |
*b |
Suction Cup |
(1) Position the back door glass.
- Using 2 suction cups, place a back door glass in the correct position.
- Check that the whole contact surface of the back door glass rim is perfectly even.
- Align the matchmarks on the back door glass and back door panel.
NOTICE:
Check that the back window glass clips are engaged to the back door panel correctly.
- Remove the back door glass.
- Using a brush, coat the installation surfaces on the back door panel with body primer.
NOTICE:
- Do not coat the adhesive with body primer.
- Do not apply too much body primer.
- Allow the body primer to dry for 3 minutes or more.
- Throw away any leftover body primer.
HINT:
If an area other than specified is coated by accident, wipe off the body primer with a clean piece of cloth before it dries.

*1 |
Back Window Glass Adhesive Dam |
- |
- |
*a |
Back Side |
- |
- |
![]() |
Glass Primer |
- |
- |
Standard Dimension:
Area | Dimension | Area | Dimension |
|---|---|---|---|
a |
10.0 mm (0.394 in.) or more |
b |
28.7 mm (1.13 in.) or more |
c |
18.0 mm (0.709 in.) or more |
d |
28.7 mm (1.13 in.) or more |
e |
12.0 mm (0.472 in.) or more |
f |
11.2 mm (0.441 in.) or more |
(1) Using a brush or a sponge, coat the application area of the adhesive with glass primer.
NOTICE:
- Do not apply too much glass primer.
- Allow the glass primer to dry for 3 minutes or more.
- Throw away any leftover glass primer.
HINT:
- Apply glass primer to the ceramic notches.
- If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.

*a |
Nozzle |
- |
- |
Adhesive:
Toyota Genuine Windshield Glass Adhesive (High modulus type) or equivalent
(1) Apply adhesive to the back door glass.
- Cut off the tip of the cartridge nozzle as shown in the illustration.
Standard Dimension:
Area
Dimension
Area
Dimension
a
10.0 to 13.0 mm (0.394 to 0.512 in.)
b
6.0 to 9.0 mm (0.197 to 0.236 in.)
- Load the sealer gun with cartridge.

*1 |
Back Window Glass Adhesive Dam |
- |
- |
*a |
Inside |
- |
- |
![]() |
Adhesive |
- |
- |
Standard Dimension:
Item | Dimension | Item | Dimension |
|---|---|---|---|
a |
23.5 mm (0.925 in.) |
b |
34.7 mm (1.37 in.) |
c |
6.0 mm (0.236 in.) |
d |
34.7 mm (1.37 in.) |
e |
12.5 mm (0.492 in.) |
- |
- |
(1) Apply adhesive to the back door glass as shown in the illustration.

*a |
Matchmark |
*b |
Suction Cup |
(1) Install the back door glass.
- Using 2 suction cups, position the back door glass so that the matchmarks are aligned, and press it in gently along the rim.
NOTICE:
- Check that the No. 1 back window glass spacer and No. 2 back window glass spacer are engaged to the back door panel correctly.
- Check the clearance between the back door panel and back door glass.
- Lightly press the front surface of the back door glass to ensure a close fit.
HINT:
Press the glass with force of 98 N (10 kgf, 22.0 lbf) or more.
- Using a scraper, remove any excess or protruding adhesive.
- Hold the back door glass using protective tape until the applied adhesive becomes hard.
HINT:
Follow the instructions supplied by the adhesive manufacturer or in the corresponding instruction manual for the minimum amount of time necessary to wait before driving the Toyota Prius vehicle.

(1) Connect the connector.

(1) Connect the 2 connectors.
7. INSTALL REAR LIGHT ASSEMBLY
![]() |
Click here |
8. INSTALL BACK DOOR OUTSIDE GARNISH LOWER MOULDING LH
9. INSTALL BACK DOOR OUTSIDE GARNISH LOWER MOULDING RH
10. INSTALL BACK DOOR TRIM BOARD ASSEMBLY
11. INSTALL BACK DOOR SIDE GARNISH RH
12. INSTALL BACK DOOR SIDE GARNISH LH
13. INSTALL BACK DOOR TRIM UPPER PANEL ASSEMBLY
14. INSPECT FOR LEAK AND REPAIR

(1) Inspect for leaks by the below procedure.
1. After the adhesive has hardened, apply water from the outside of the Toyota Prius vehicle. Check that no water leaks into the cabin.
2. If water leaks into the cabin, allow the water to dry and add adhesive.
3. Remove the protective tape.

































