Power Window Control System

In this manual: Power Window Control System
How To Troubleshoot Ecu Controlled Systems — 1How To Use This Manual — 1Identification Information — 1Repair Instruction — 1Terms — 12zr-fxe Air Cleaner Filter Element — 12zr-fxe Auxiliary Battery — 12zr-fxe Coolant (for Engine Coolant) — 12zr-fxe Oil And Oil Filter — 12zr-fxe Spark Plug — 1Air Conditioning Filter — 1Battery Cooling Filter — 1Brake Fluid — 1Coolant (for Inverter) — 1Front Brake Flexible Hose — 1Front Disc Brake Pad — 1Front Lower Ball Joint — 1Front Wheel Alignment — 1Front Wiper Rubber — 1General Maintenance — 1M20a-fxs Air Cleaner Filter Element — 1M20a-fxs Auxiliary Battery — 1M20a-fxs Coolant (for Engine Coolant) — 1M20a-fxs Oil And Oil Filter — 1M20a-fxs Spark Plug — 1Pa10/pb10/pb12 Hybrid Transaxle Fluid — 1Q810 Hybrid Transaxle Fluid — 1Rear Brake Flexible Hose — 1Rear Disc Brake Pad — 1Rear Wheel Alignment — 1Steering Column — 1Tire And Wheel — 1Transmitter Battery — 1When Disconnecting Or Reconnecting Battery Terminal — 1When Replacing Or Removing/installing Parts — 1Automatic High Beam Main Switch — 1Automatic High Beam System — 1Driver Monitor Camera — 1Driver Monitor Camera System — 1Driver Monitor Ecu — 1Front Camera — 1Front Camera System — 1Front Radar Sensor System — 1Front Side Radar Sensor — 1Front Side Radar Sensor System — 1Millimeter Wave Radar Sensor — 1Utility — 1Advanced Park — 1Advanced Park Main Switch — 1Amplifier Antenna — 1Audio And Visual System — 1Front Door Speaker — 1Instrument Panel Speaker — 1Microphone — 1Noise Filter — 1Pillar Speaker — 1Radio Antenna Cord (for Back Door) — 1Radio Antenna Cord (for Instrument Panel) — 1Radio Antenna Cord (for Roof) — 1Radio Receiver — 1Rear Door Speaker — 1Roof Antenna — 1Stereo Component Amplifier — 1Stereo Jack Adapter Assembly — 1Window Glass Antenna Wire — 1Back-up Battery — 1Dcm(telematics Transceiver) — 1Manual(sos)switch — 1Safety Connect System — 1Telephone And Gps Antenna (for Front Side) — 1Telephone And Gps Antenna (for Roof Side) — 1Telephone And Gps Antenna Cords — 1Garage Door Opener System (for Digital Inner Mirror) — 1Garage Door Opener System (for Ec Inner Mirror) — 1Blind Spot Monitor Sensor — 1Blind Spot Monitor System — 1Clearance Warning Ecu — 1Intuitive Parking Assist System — 1Panoramic View Monitor Switch — 1Panoramic View Monitor System — 1Parking Assist Ecu — 1Parking Assist Light — 1Parking Assist Monitor System — 1Parking Support Brake System — 1Rear View Monitor System — 1Television Camera (for Front) — 1Television Camera (for Rear) — 1Television Camera (for Side) — 1Ultrasonic Sensor (for Front) — 1Ultrasonic Sensor (for Rear) — 1Brake Actuator — 1Brake Pedal Stroke Sensor — 1Electronically Controlled Brake System — 1Front Speed Sensor — 1Rear Speed Sensor (for Awd) — 1Steering Angle Sensor — 1Brake Booster — 1Brake Fluid — 1Brake Line — 1Brake Pedal — 1Brake System — 1Electric Parking Brake Actuator — 1Electric Parking Brake Switch — 1Electric Parking Brake System — 1Forced Release — 1Front Axle Hub — 1Front Axle Hub Bolt — 1Rear Axle Carrier (for 2wd) — 1Rear Axle Carrier (for Awd) — 1Rear Axle Hub (for 2wd) — 1Rear Axle Hub (for Awd) — 1Rear Axle Hub Bolt — 1Steering Knuckle — 1Drive Shaft System — 1Front Drive Shaft Assembly — 1Rear Drive Shaft Assembly — 1Combination Switch — 1Electronic Shift Lever System — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Oil Seal — 1Hybrid Transaxle System — 1Input Shaft Oil Seal — 1Motor Cable — 1Pa10 Hybrid Vehicle Transaxle — 1Pa10 Manual Parking Lock Release — 1Pa10 Oil Cooler — 1Pb10/pb12 Hybrid Vehicle Transaxle — 1Pb10/pb12 Manual Parking Lock Release — 1Pb10/pb12 Oil Cooler — 1Shift Control Actuator — 1Shift Lever — 1Shift Lever Knob — 1Differential Side Gear Shaft — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Side Gear Oil Seal — 1Motor Cable — 1Rear Traction Motor — 1Coolant (for Engine) — 1Cooling Fan Motor — 1Cooling Fan System — 1Radiator — 1Relay — 1Thermostat — 1Water Pump — 1Canister — 1Egr Cooler — 1Egr Valve — 1Emission Control System — 1Fuel Tank Cap — 1Pcv Valve — 1Purge Valve — 1Vacuum Sensor — 1Air Fuel Ratio Sensor — 1Camshaft Oil Control Valve — 1Camshaft Position Sensor — 1Crankshaft Position Sensor — 1Ecm — 1Engine Coolant Temperature Sensor — 1Heated Oxygen Sensor — 1Ignition Coil And Spark Plug — 1Ignition System — 1Knock Sensor — 1Mass Air Flow Meter — 1Relay — 1Sfi System — 1Throttle Body — 1Camshaft — 1Cylinder Block — 1Cylinder Head — 1Cylinder Head Gasket — 1Engine — 1Engine Assembly — 1Engine Unit — 1Front Crankshaft Oil Seal — 1Rear Crankshaft Oil Seal — 1Fuel Filter — 1Fuel Injector — 1Fuel Pressure Regulator — 1Fuel Pump — 1Fuel Sender Gauge Assembly — 1Fuel System — 1Fuel Tank — 1Air Cleaner Filter Element — 1Exhaust Manifold — 1Exhaust Pipe — 1Intake Manifold — 1Intake System — 1Lubrication System — 1Oil And Oil Filter — 1Oil Pan And Oil Level Sensor — 1Oil Pressure Switch — 1Oil Pump — 1Accelerator Pedal Sensor — 1Battery Blower (for Hev Model) — 1Battery Ecu (for Hev Model) — 1Battery Ecu (for Phev Model) — 1Battery Voltage Sensor (for Phev Model) — 1Charge Cable (for Phev Model) — 1Charge Indicator (for Phev Model) — 1Charge Inlet (for Phev Model) — 1Combination Switch — 1Coolant (for Inverter) — 1Cooler (for Phev Model) — 1Electric Vehicle Charger Assembly (for Phev Model) — 1Frame Wire (for Hev Model) — 1Frame Wire (for Phev Model) — 1Heater Relay (for Phev Model) — 1Hv Battery (for Hev Model) — 1Hv Battery (for Phev Model) — 1Hv Battery Heater (for Phev Model) — 1Hv Battery Stack (for Phev Model) — 1Hv Relay Assembly (for Hev Model) — 1Hv Relay Assembly (for Phev Model) — 1Hybrid Battery System (for 2zr-fxe) — 1Hybrid Battery System (for M20a-fxs) — 1Hybrid Battery System (for Phev Model) — 1Hybrid Vehicle Control Ecu — 1Inverter With Converter (for Hev Model) — 1Motor Generator Control System (for 2zr-fxe) — 1Plug-in Charge Control System (for Phev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Service Plug Grip (for Hev Model) — 1Sub Radiator — 1Water Pump With Motor — 1Auxiliary Battery — 1Battery Current Sensor — 1Charging System — 1Solar Charging System — 1Solar Control Unit — 1Solar Roof — 1Can Communication System (for Hev Model) — 1Lin Communication System — 1Network Gateway Ecu — 1Integration Control Supply — 1Main Body Ecu — 1Power Integration System — 1Sub Battery System — 1Power Steering Ecu — 1Power Steering System — 1Heated Steering Wheel Controller — 1Heated Steering Wheel System — 1Steering Column Assembly — 1Steering Heater Switch — 1Steering Pad Switch — 1Steering System — 1Steering Wheel — 1Front Lower Ball Joint — 1Front Lower Suspension Arm (for 2zr-fxe Lh Side) — 1Front Lower Suspension Arm (for 2zr-fxe Rh Side) — 1Front Lower Suspension Arm (for M20a-fxs) — 1Front Shock Absorber — 1Front Stabilizer Bar — 1Front Suspension Member — 1Rear Coil Spring — 1Rear Lower Arm (for Awd Lh Side) — 1Rear Lower Arm (for Awd Rh Side) — 1Rear Lower Arm (for Hev Model 2wd) — 1Rear Lower Arm (for Phev Model) — 1Rear Shock Absorber — 1Rear Stabilizer Bar — 1Rear Suspension Member (for 2wd) — 1Rear Suspension Member (for Awd) — 1Rear Trailing Arm — 1Rear Upper Arm — 1Tire And Wheel System — 1Tire Repair Seal — 1Tire Pressure Warning Receiver — 1Tire Pressure Warning System — 1Tire Pressure Warning Valve — 1Acoustic Vehicle Alerting System — 1Vehicle Approaching Speaker — 1Vehicle Approaching Speaker Ecu — 1Back Door — 1Back Door Closer Ecu — 1Back Door Opener Switch — 1Back Door Support — 1Back Door Weatherstrip — 1Charge Lid Courtesy Switch — 1Charge Lid Opener Motor Assembly — 1Charge Lid Opener System — 1Charge Lid Opener Unit — 1Front Door — 1Front Door Opening Trim Weatherstrip — 1Fuel Lid Opener Motor Assembly — 1Fuel Lid Opener Switch — 1Fuel Lid Opener System — 1Hood — 1Hood Lock Control Cable Assembly — 1Power Back Door Closer Switch — 1Power Back Door Control Switch — 1Power Back Door Drive Unit — 1Power Back Door System — 1Power Back Door Touch Sensor — 1Power Back Door Warning Buzzer — 1Rear Door — 1Rear Door Opening Trim Weatherstrip — 1Reserve Lock Switch — 1Front Bumper — 1Front Door Belt Moulding — 1Front Door Window Frame Moulding — 1Front Fender — 1Front Pillar Upper Cover — 1Grille Shutter — 1Grille Shutter System — 1Name Plate — 1Quarter Garnish — 1Rear Bumper — 1Rear Door Belt Moulding — 1Rear Door Window Frame Moulding — 1Rear Wheel House Plate — 1Rocker Panel Moulding — 1Roof Drip Side Finish Moulding — 1Roof Garnish — 1Wheel Opening Moulding (for Front Side) — 1Wheel Opening Moulding (for Rear Side) — 1Windshield Outside Moulding — 1Horn — 1Horn System — 1Relay — 1Automatic Light Control Sensor — 1Back-up Light Assembly — 1Charge Lid Light — 1Front Marker Light — 1Hazard Warning Switch — 1Headlight Assembly — 1Headlight Dimmer Switch — 1Headlight Leveling Switch — 1High Mounted Stop Light Assembly — 1Illumination Light Assembly — 1License Plate Light Assembly — 1Lighting System — 1Rear Combination Light Assembly — 1Rear Light Assembly — 1Rear Side Marker Light Assembly — 1Relay — 1Side Turn Signal Light Assembly — 1Stop Light Switch — 1Switch Housing — 1Outer Mirror Switch — 1Outer Rear View Mirror — 1Outer Rear View Mirror Cover — 1Outer Rear View Mirror Glass — 1Power Mirror Control System — 1Back Door Glass — 1Front Passenger Side Power Window Switch — 1Power Window Control System — 1Power Window Master Switch — 1Power Window Regulator Motor (for Front Door) — 1Power Window Regulator Motor (for Rear Door) — 1Rear Power Window Switch — 1Relay — 1Roof Window Fix Glass — 1Window Defogger System — 1Windshield Deicer Switch — 1Windshield Deicer System — 1Windshield Glass — 1Front Wiper Motor — 1Rain Sensor — 1Relay — 1Washer Motor — 1Washer Nozzle (for Front Side) — 1Washer Nozzle (for Rear Television Camera) — 1Wiper And Washer System — 1Wiper Ecu — 1Wiper Switch — 1Back Door Lock — 1Door Control Receiver — 1Door Control Switch — 1Door Control Transmitter — 1Door Lock Release Motor (for Rear Side) — 1Door Outside Handle (for Rear Side) — 1Front Door Lock — 1Power Door Lock Control System — 1Rear Door Lock — 1Transmitter Battery — 1Wireless Door Lock Control System — 1Accumulator — 1Air Conditioning Amplifier — 1Air Conditioning Panel — 1Air Conditioning Pressure Sensor — 1Air Conditioning Unit — 1Ambient Temperature Sensor — 1Blower Unit — 1Condenser (for Hev Model) — 1Condenser (for Phev Model) — 1Discharge Temperature Sensor — 1Electric Expansion Valve (cooling) — 1Electric Expansion Valve (heating) — 1Evaporator Pipe Temperature Sensor — 1Evaporator Pressure Regulator — 1Front Blower Motor — 1Front Evaporator Front Solenoid Valve — 1Air Conditioning System (for Hev Model) — 1Front Evaporator Temperature Sensor — 1Heat Exchanger Temperature Sensor — 1Heat Pump Ecu — 1High Pressure Magnetic Valve — 1Humidity Sensor — 1Internal Condenser Temperature Sensor — 1Low Pressure Magnetic Valve — 1Refrigerant (for Hfc-134a(r134a)) — 1Refrigerant Line (for Hev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Room Temperature Sensor — 1Solar Sensor — 1Floor Carpet — 1Front Console Box — 1Instrument Panel Safety Pad — 1Roof Headlining — 1Roof Sunshade — 1Ambient Light (for Driver Side) — 1Ambient Light (for Front Passenger Side) — 1Back Door Courtesy Switch — 1Footwell Light — 1Glove Box Light — 1Lighting System — 1Luggage Compartment Room Light — 1Personal Light — 1Room Light — 1Vanity Light — 1Vanity Light Switch — 1Combination Meter — 1Meter / Gauge System — 1Trip Switch — 1Digital Inner Mirror — 1Digital Rear-view Mirror System — 1Inner Mirror Monitor Camera — 1Inner Rear View Mirror (w/o Ec Mirror) — 1Accessory Power Outlet System — 1Power Outlet Socket (for Console Box Front Side) — 1Power Outlet Socket (for Console Box Rear Side) — 1Power Outlet Socket (for Console Box) — 1Power Outlet Socket (for Luggage Compartment) — 1Power Outlet Switch — 1Wireless Charger Assembly — 1Wireless Charging System — 1Climate Control Seat System — 1Front Power Seat Control System (w/ Memory) — 1Front Power Seat Motor Assembly — 1Front Seat Assembly (for Power Seat) — 1Front Seat Cushion Heater (for Power Seat) — 1Front Seatback Heater (for Power Seat) — 1Lumbar Support Adjuster Assembly — 1Power Seat Control Ecu — 1Power Seat Switch — 1Power Seat Track Rail Assembly — 1Rear Seat Assembly — 1Rear Seat Cushion Heater — 1Rear Seat Reminder System — 1Rear Seatback Heater — 1Seat Heater Control — 1Seat Heater Switch (for Front Seat) — 1Seat Heater Switch (for Rear Side) — 1Seat Heater System — 1Seat Memory Switch — 1Child Restraint Seat Anchor Bracket — 1Front Seat Inner Belt Assembly — 1Front Seat Outer Belt Assembly — 1Occupant Detection Sensor (for Front Passenger Side) — 1Rear Center Seat Outer Belt Assembly — 1Rear Seat Inner Belt Assembly (for Rh Side) — 1Rear Seat Outer Belt Assembly — 1Seat Belt Warning System (w/ Occupant Classification System) — 1Tongue Plate Stopper — 1Airbag System — 1Center Airbag Sensor Assembly — 1Curtain Shield Airbag Assembly — 1Front Airbag Sensor — 1Front Passenger Airbag Assembly — 1Front Seat Side Airbag Assembly — 1Inspection After Collision — 1Knee Airbag Assembly — 1Occupant Classification System — 1Rear Seat Side Airbag Assembly — 1Side Airbag Sensor (for Center Pillar) — 1Side Airbag Sensor (for Front Door) — 1Spiral Cable — 1Steering Pad — 1Certification Ecu — 1Digital Key Ecu — 1Digital Key Receiver (for Front Floor) — 1Digital Key Receiver (for Outside Luggage Compartment) — 1Digital Key Receiver (for Rear Door) — 1Digital Key System — 1Electrical Key Oscillator (for Front Floor) — 1Electrical Key Oscillator (for Outside Luggage Compartment) — 1Electrical Key Oscillator (for Rear Floor) — 1Engine Hood Courtesy Switch — 1Id Code Box — 1Smart Key System (for Start Function) — 1
~128min read
  • Precaution
  • Parts Location
  • System Diagram
  • How To Proceed With Troubleshooting
  • Operation Check
  • Registration
  • Customize Parameters
  • Problem Symptoms Table
  • Terminals Of Ecu
  • Data List / Active Test
  • Diagnostic Trouble Code Chart
  • VEHICLE CONTROL HISTORY (RoB)
  • Master SW Malfunction (B231200)
  • D-Door P/W Motor Component Internal Failure (B231D96)
  • P-Door P/W Motor Component Internal Failure (B231E96)
  • RR-Door P/W Motor Component Internal Failure (B231F96)
  • RL-Door P/W Motor Component Internal Failure (B232096)
  • Remote Up / Down Function does not Operate
  • Driver Side Power Window does not Operate with Power Window Master Switch
  • Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch
  • Rear Power Window RH does not Operate with Rear Power Window Switch RH
  • Driver Side Power Window Auto Up / Down Function does not Operate with Power Window Master Switch
  • Front Passenger Side Power Window Auto Up / Down Function does not Operate with Front Passenger Side Power Window Switch
  • Rear Power Window LH Auto Up / Down Function does not Operate with Rear Power Window Switch LH
  • Rear Power Window LH does not Operate with Rear Power Window Switch LH
  • Rear Power Window RH Auto Up / Down Function does not Operate with Rear Power Window Switch RH
  • All Power Windows do not Operate with Driver Side Door Key Cylinder or Wireless Transmitter
  • Key-off Operation Function Operates even if Operating Conditions are not Satisfied
  • Auto Up Operation does not Fully Close Power Window (Jam Protection Function is Activated)
  • Auto Down Operation does not Fully Open Power Window (Catch Protection Function is Activated)
  • Jam Protection Function does not Operate

Precaution

PRECAUTION

PRECAUTION FOR DISCONNECTING CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click here

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click here

POWER WINDOW CONTROL SYSTEM PRECAUTIONS

NOTICE:

  • The power window control system uses the LIN communication system and CAN communication system. Inspect the communication functions by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly.

    Click here

  • The power window control system prohibits the auto up and down functions if the jam protection function or catch protection function malfunctions.
  • If a power window regulator motor assembly has been replaced with a new one, initialize a power window control system.

    Click here

  • If a power window regulator motor assembly and door window regulator sub-assembly have been removed and installed, or if a power window regulator motor assembly was reused when a door glass or door glass run was replaced, initialize the power window control system.

    Click here

  • The jam protection function or catch protection function may operate unexpectedly, even when the power window control system is normal, due to detection of a value different than the operation learned value when the door glass moving speed changes sharply under any of the following conditions:
    1. A power window is being opened or closed while the Toyota Prius vehicle is driven on a rough road.
    2. A power window is being opened or closed while the door is being opened or closed.
    3. The voltage changes abruptly.
  • Do not disconnect the cable from the negative (-) auxiliary battery terminal while the ignition switch is ON. If the cable is disconnected from the negative (-) auxiliary battery terminal while the ignition switch is ON, the power window of each seat may become uninitialized.

    Click here

Parts Location

PARTS LOCATION

ILLUSTRATION

*1

MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

*2

POWER WINDOW REGULATOR SWITCH ASSEMBLY

*3

REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Door)

*4

REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Door)

*5

POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Driver Door)

*6

POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Front Passenger Door)

*7

POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Rear LH Door)

*8

POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Rear RH Door)

*9

FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH

-

-

ILLUSTRATION

*1

CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

*2

COMBINATION METER ASSEMBLY

*3

MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

*4

POWER DISTRIBUTION BOX ASSEMBLY

- ECU-B NO. 2 FUSE

- DOOR F/L FUSE

- DOOR F/R FUSE

- DOOR R/L FUSE

- DOOR R/R FUSE

*5

DLC3

-

-

System Diagram

SYSTEM DIAGRAM

How To Proceed With Troubleshooting

HINT:

  • Use the following procedure to troubleshoot the power window control system.
  • *: Use the GTS.

PROCEDURE

  1. Toyota Prius Vehicle BROUGHT TO WORKSHOP

NEXT
  1. CUSTOMER PROBLEM ANALYSIS

HINT:

  • In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
  • Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
  • The following 5 items are important points for problem analysis:

    What

    Toyota Prius Vehicle model, system name

    When

    Date, time, occurrence frequency

    Where

    Road conditions

    Under what conditions?

    Driving conditions, weather conditions

    How did it happen?

    Problem symptoms

NEXT
  1. READ AND SAVE OPERATION HISTORY*

NOTICE:

  • If the Toyota Prius vehicle or vehicle controls are operated (for example, during initial inspection when the vehicle is brought in for repair) before operation history has been read out and saved, the operation history information could be lost.
  • The function "Read operation history" uses the current system time setting inside the GTS and the time counter inside the controlling ECU to calculate the timings shown in the operation history. For this reason, before reading out the operation history, first make sure that the GTS system clock is accurately set to the current time.

(a) Read and save operation history using the GTS.

Body Electrical > Main Body > Utility

Toyota Prius Vehicle Control History (RoB)

NEXT
  1. PRE-CHECK

(a) Measure the auxiliary battery voltage with the ignition switch off.

Standard Voltage:

11 to 14 V

If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.

(b) Check the fuses and relays.

(c) Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.

NEXT
  1. INSPECT COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*

(a) Using the GTS, check for CAN communication system DTCs.

for HEV Model: Click here

for PHEV Model: Click here

Result

Proceed to

CAN DTCs are not output

A

CAN DTCs are output

B

B

GO TO CAN COMMUNICATION SYSTEM

for HEV Model: Click here

for PHEV Model: Click here

A
  1. INSPECT COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*

(a) Using the GTS, check for LIN communication system DTCs.

Result

Proceed to

LIN DTCs are not output

A

LIN DTCs are output

B

B

GO TO LIN COMMUNICATION SYSTEM

A
  1. CHECK FOR DTC*

(a) Clear the DTCs.

Body Electrical > Main Body > Clear DTCs

(b) Recheck for DTCs.

Body Electrical > Main Body > Trouble Codes

Result

Proceed to

DTCs are not output

A

DTCs are output

B

B

GO TO DIAGNOSTIC TROUBLE CODE CHART

A
  1. PROBLEM SYMPTOMS TABLE

(a) Refer to Problem Symptoms Table.

Click here

Result

Proceed to

Fault is not listed in problem symptoms table

A

Fault is listed in problem symptoms table

B

B

GO TO STEP 10

A
  1. OVERALL ANALYSIS AND TROUBLESHOOTING*

(a) Operation Check

Click here

(b) Terminals of ECU

Click here

(c) Data List / Active Test

Click here

(d) Inspection

NEXT
  1. ADJUST, REPAIR OR REPLACE

(a) Check if any of the door window regulator sub-assemblies, power window regulator motor assemblies, door glass or door glass runs have been removed and reinstalled.

Result

Proceed to

Any of the door window regulator sub-assemblies, power window regulator motor assemblies, door glass or door glass runs have been removed and reinstalled.

A

The door window regulator sub-assemblies, power window regulator motor assemblies, door glass and door glass runs have not been removed and reinstalled.

B

B

GO TO STEP 12

A
  1. INITIALIZE POWER WINDOW CONTROL SYSTEM

(a) If any of the door window regulator sub-assemblies, power window regulator motor assemblies, door glass or door glass runs have been removed and reinstalled, initialize the power window control system.

Click here

NEXT
  1. CONFIRMATION TEST

NEXT

END

Operation Check

OPERATION CHECK

NOTICE:

When troubleshooting a function, first make sure that the function is set to the default setting.

Click here

CHECK WINDOW LOCK FUNCTION

HINT:

Before performing the window lock switch operation check, make sure that the window lock switch is off (the switch indicator is off).

(a) Turn the window lock switch of the multiplex network master switch assembly on (the switch indicator is on) and check that the front passenger and rear windows are disabled.

OK:

Front passenger and rear windows are disabled.

(b) Turn the window lock switch off (the switch indicator is off) and check that the front passenger and rear windows can be operated normally.

OK:

Front passenger and rear windows operate normally.

CHECK MANUAL UP / DOWN FUNCTION

(a) Check that the driver door power window operates as follows:

OK

Condition

Master Switch

Switch Operation

Power Window

Ignition switch ON

Driver door

Pulled halfway up

UP (Closes)

Pushed halfway down

DOWN (Opens)

(b) Check that the front passenger door power window and rear door power windows operate as follows:

OK

Condition

Regulator Switch

Switch Operation

Power Window

  • Ignition switch ON
  • Window lock switch off

Front passenger door

Pulled halfway up

UP (Closes)

Pushed halfway down

DOWN (Opens)

Rear LH door

Pulled halfway up

UP (Closes)

Pushed halfway down

DOWN (Opens)

Rear RH door

Pulled halfway up

UP (Closes)

Pushed halfway down

DOWN (Opens)

CHECK AUTO UP / DOWN FUNCTION

(a) Check that the driver door power window operates as follows:

OK

Condition

Master Switch

Switch Operation

Power Window

Ignition switch ON

Driver door

Pulled up (One touch operation)

AUTO UP (Closes)

Pushed down (One touch operation)

AUTO DOWN (Opens)

(b) Check that the front passenger door power window and rear door power windows operate as follows:

OK

Condition

Regulator Switch

Switch Operation

Power Window

  • Ignition switch ON
  • Window lock switch off

Front passenger door

Pulled up (One touch operation)

AUTO UP (Closes)

Pushed down (One touch operation)

AUTO DOWN (Opens)

Rear LH door

Pulled up (One touch operation)

AUTO UP (Closes)

Pushed down (One touch operation)

AUTO DOWN (Opens)

Rear RH door

Pulled up (One touch operation)

AUTO UP (Closes)

Pushed down (One touch operation)

AUTO DOWN (Opens)

CHECK REMOTE MANUAL UP / DOWN FUNCTION

(a) Check that the front passenger door power window and rear door power windows operate as follows:

OK

Condition

Master Switch

Switch Operation

Power Window

Ignition switch ON

Front passenger door

Pulled halfway up

UP (Closes)

Pushed halfway down

DOWN (Opens)

Rear LH door

Pulled halfway up

UP (Closes)

Pushed halfway down

DOWN (Opens)

Rear RH door

Pulled halfway up

UP (Closes)

Pushed halfway down

DOWN (Opens)

CHECK REMOTE AUTO UP / DOWN FUNCTION

(a) Check that the front passenger door power window and rear door power windows operate as follows:

OK

Condition

Master Switch

Switch Operation

Power Window

Ignition switch ON

Front passenger door

Pulled up (One touch operation)

AUTO UP (Closes)

Pushed down (One touch operation)

AUTO DOWN (Opens)

Rear LH door

Pulled up (One touch operation)

AUTO UP (Closes)

Pushed down (One touch operation)

AUTO DOWN (Opens)

Rear RH door

Pulled up (One touch operation)

AUTO UP (Closes)

Pushed down (One touch operation)

AUTO DOWN (Opens)

CHECK KEY-OFF OPERATION FUNCTION

(a) Check that each power window can be operated with the multiplex network master switch assembly, power window regulator switch assembly or rear power window regulator switch assembly after the ignition switch is turned off.

HINT:

If the window lock switch is on, the power windows cannot be operated using the power window regulator switch assembly and rear power window regulator switch assemblies. Therefore, turn the window lock switch off before checking the power window operation.

(b) Check that the key-off operation function does not operate immediately after the driver door or front passenger door is opened.

HINT:

If a power window is being operated by auto operation while the key-off operation function is on, and the driver door or front passenger door is opened, the power window will continue operating.

(c) Check that all of the power windows cannot be operated after more than approximately 45 seconds have elapsed since the ignition switch is turned off.

CHECK WIRELESS TRANSMITTER-LINKED FUNCTION*

  • *: This function is set through a customize setting, as it is off by default.

(a) Check that all of the power windows operate as follows when operating the key:

OK

Condition

Transmitter Operation

Power Window

No key is inside Toyota Prius vehicle, and all doors are closed and locked

UNLOCK switch pressed for more than 3 seconds

DOWN (Opens)

UNLOCK switch released

STOP

CHECK KEY-LINKED FUNCTION*

  • *: This function is set through a customize setting, as it is off by default.

(a) Check that all of the power windows operate as follows:

OK

Condition

Door Key Cylinder Operation

Power Window

No key is inside Toyota Prius vehicle, and all doors are closed

Turned to the lock position and held for more than 2 seconds

UP (Closes)

Returned to neutral position

STOP

Turned to the unlock position and held for more than 2 seconds

DOWN (Opens)

Returned to neutral position

STOP

CHECK WINDOW OPEN WARNING FUNCTION

(a) Open a window using the power window switch.

(b) Turn the ignition switch from ON to off, open the driver door with the Key in the Toyota Prius vehicle and check that message is displayed on the multi-information display in the combination meter assembly.

CHECK JAM PROTECTION FUNCTION

(a) Check the basic function.

CAUTION:

Do not put your fingers between the door frame and door glass to check the jam protection function. Also, prevent any part of your body from being caught during inspection.

HINT:

The jam protection function is operative during both the auto up and manual up operations while the hybrid control system is started or the ignition switch is ON, and also for approximately 45 seconds after the ignition switch is turned off.

(1) Fully open the power window.

*a

Check Jig

*b

Cloth

(2) Set a check jig wrapped with a piece of cloth near the power window fully closed position.

(3) Operate the auto up or manual up function and check that the power window stops and goes down after the check jig is caught between the door glass and door frame, and stops.

HINT:

  • If a manual up operation is performed from the seat, the door glass will lower approximately 45 mm (1.7717 in.) from the point it contacts the end of the hammer or continue lowering for approximately 5 seconds and then stop.
  • If a manual up operation is not performed from the seat, the door glass will lower approximately 145 mm (5.7087 in.) from the point it contacts the end of the hammer or continue lowering for approximately 5 seconds and then stop.
  • After the jam protection function operates when an auto up or manual up operation is performed, the jam protection function will not operate when the manual up operation is performed again within approximately 4 seconds.
  • After the catch protection function has operated, the auto up function will not operate the first time the power window auto up switch is operated. The auto up function will operate normally after the first power window switch operation.

(4) While the power window is moving down, check that the door glass cannot be raised using the power window switch.

CHECK CATCH PROTECTION FUNCTION

(a) Check the basic function.

HINT:

The catch protection function is operative during both the auto down and manual down operations while the hybrid control system is started or the ignition switch is ON, and also for approximately 45 seconds after the ignition switch is turned off.

(1) Fully close all of the power windows.

(2) Operate the auto down or manual down function to open the power window, grasp the upper edge of the door glass with one or two hands and check that the power window stops.

HINT:

After the catch protection function has operated when an auto down or manual down operation was performed, the catch protection function will not operate if the manual down operation is performed again within approximately 4 seconds.

Registration

REGISTRATION

PROCEDURE

1. INITIALIZE POWER WINDOW CONTROL SYSTEM

NOTICE:

  • When any of the door window regulator sub-assemblies, power window regulator motor assemblies, door glass or door glass runs have been removed and reinstalled, the power window control system must be initialized. Functions such as the auto up and down function, jam protection function, catch protection function, remote control function, key-linked function, wireless transmitter-linked function, key-off operation function, window open warning function and suggestion service function will not operate if initialization is not performed.
  • When performing initialization, do not perform any other procedures.
  • Make sure to park the Toyota Prius vehicle and turn off all electrical systems before performing initialization. Initialization will be canceled if the vehicle is driven during initialization.
  • When performing initialization, use the power window switch of each door to initialize each power window.
  • Make sure not to hit, strike or vibrate the door glass during initialization because the Toyota Prius vehicle is learning the sliding resistance of the door glass.
  • Make sure not to turn the ignition switch off during initialization.

HINT:

  • If initialization cannot be completed properly, the LIN communication system may be malfunctioning.

    Click here

  • If the auxiliary battery has been replaced, it is not necessary to initialize the power window regulator motor assemblies.
  • The initialization status of the power window of each seat can be checked using the Data List.

    Click here

(a) Perform initialization according to the table below.

Condition of Power Window

Proceed to

A power window regulator motor assembly has been replaced with a new one.

Procedure A

  • Power window regulator motor assembly has been removed/installed or a door glass and/or door glass run, etc. have been removed/installed or replaced with new ones.
  • Power window cannot be fully opened via a down operation (door glass remains visible).
  • Power window cannot be fully closed (erroneously operates in reverse) after initialization.
  • Power window cannot be fully opened (erroneously stops) after initialization.
  • Instructions to perform initialization appear in other troubleshooting procedures.

HINT:

Use this procedure if a power window regulator motor assembly is being reused.

Procedure B

Power window unexpectedly operates in reverse or stops due to a change in the sliding resistance after a fitting adjustment is made.

Procedure C

(b) Procedure A

(1) Perform window position initialization (fully closed, fully open) and sliding resistance learning.

HINT:

*: Even if the door glass is in the fully open position before performing step 3, push down and hold the switch for 1 second or more.

(c) Procedure B

(1) Perform window position initialization (fully closed, fully open) and sliding resistance learning.

Reset the power window position, perform window position initialization (fully closed, fully opened) and sliding resistance learning.

HINT:

*1: After performing step 7, release the switch, and then perform an auto down operation.

*2: After completing initialization, check that the power window can be fully closed using an auto up operation.

If initialization cannot be completed properly, the LIN communication system may be malfunctioning.

Click here

(d) Procedure C

(1) Perform sliding resistance learning.

HINT:

If the jam protection function or catch protection function continues to operate even after performing steps 4, 5 and 6, perform the procedure again from step 3.

Customize Parameters

CUSTOMIZE PARAMETERS

CUSTOMIZE POWER WINDOW CONTROL SYSTEM

NOTICE:

  • When the customer requests a change in a function, first make sure that the function can be customized.
  • Be sure to make a note of the current settings before customizing.
  • When troubleshooting a function, first make sure that the function is set to the default setting.

(a) Customizing with the GTS

(1) Select the setting by referring to the table below.

Power Window

Tester Display

Description

Default

Setting

ECU

Door Key P/W Up Function

Function to close the power windows using the mechanical key

Disable

$00:Disable,$01:Enable

Main body ECU (Multiplex network body ECU)

Door Key P/W Down Function

Function to open the power windows using the mechanical key

Disable

$00:Disable,$01:Enable

Main body ECU (Multiplex network body ECU)

P/W Down W/ Transmit Function

Function to open the power windows using the key

Disable

$00:Disable,$01:Enable

Main body ECU (Multiplex network body ECU)

P/W Operation Buzzer W/ Transmit Function

Power window buzzer answer-back of wireless function

Enable

$00:Disable,$01:Enable

Main body ECU (Multiplex network body ECU)

D Window Auto Up Function

Function to enable or disable the auto up function for the driver door power window using the multiplex network master switch assembly.

Enable

$00:Disable,$01:Enable

Main body ECU (Multiplex network body ECU)

D Window Auto Down Function

Function to enable or disable the auto down function for the driver door power window using the multiplex network master switch assembly

Enable

$00:Disable,$01:Enable

Main body ECU (Multiplex network body ECU)

P Window Auto Up Function

Function to enable or disable the auto up function for the front passenger door power window using the power window regulator switch assembly

Enable

$00:Disable,$01:Enable

Main body ECU (Multiplex network body ECU)

P Window Auto Up by Driver Function

Function to enable or disable the remote auto up function for the front passenger door power window using the multiplex network master switch assembly

Enable

$00:Disable,$01:Enable

Main body ECU (Multiplex network body ECU)

P Window Auto Down Function

Function to enable or disable the auto down function for the front passenger door power window using the power window regulator switch assembly

Enable

$00:Disable,$01:Enable

Main body ECU (Multiplex network body ECU)

P Window Auto Down by Driver Function

Function to enable or disable the remote auto down function for the front passenger door power window using the multiplex network master switch assembly

Enable

$00:Disable,$01:Enable

Main body ECU (Multiplex network body ECU)

RR Window Auto Up Function

Function to enable or disable the auto up function using the rear power window regulator switch assembly (for RH door)

Enable

$00:Disable,$01:Enable

Main body ECU (Multiplex network body ECU)

RR Window Auto Up by Driver Function

Function to enable or disable the remote auto up function for the rear RH door power window using the multiplex network master switch assembly

Enable

$00:Disable,$01:Enable

Main body ECU (Multiplex network body ECU)

RR Window Auto Down Function

Function to enable or disable the auto down function using the rear power window regulator switch assembly (for RH door)

Enable

$00:Disable,$01:Enable

Main body ECU (Multiplex network body ECU)

RR Window Auto Down by Driver Function

Function to enable or disable the remote auto down function for the rear RH door power window using the multiplex network master switch assembly

Enable

$00:Disable,$01:Enable

Main body ECU (Multiplex network body ECU)

RL Window Auto Up Function

Function to enable or disable the auto up function using the rear power window regulator switch assembly (for LH door)

Enable

$00:Disable,$01:Enable

Main body ECU (Multiplex network body ECU)

RL Window Auto Up by Driver Function

Function to enable or disable the remote auto up function for the rear LH door power window using the multiplex network master switch assembly

Enable

$00:Disable,$01:Enable

Main body ECU (Multiplex network body ECU)

RL Window Auto Down Function

Function to enable or disable the auto down function using the rear power window regulator switch assembly (for LH door)

Enable

$00:Disable,$01:Enable

Main body ECU (Multiplex network body ECU)

RL Window Auto Down by Driver Function

Function to enable or disable the remote auto down function for the rear LH door power window using the multiplex network master switch assembly

Enable

$00:Disable,$01:Enable

Main body ECU (Multiplex network body ECU)

Warning

Tester Display

Description

Default

Setting

ECU

Window Open Warning Function

Function to enable or disable the window open warning

Enable

$00:Disable,$01:Enable

Main body ECU (Multiplex network body ECU)

Proposal Services Function

Function to enable or disable the display of a message for suggestion service function

ON

$00:OFF,$01:Parked,$03:ON

Main body ECU (Multiplex network body ECU)

Others

Tester Display

Description

Default

Setting

ECU

Power Window Voice Control Function

Function to enable or disable door window open/close linked voice recognition control.*

Enable

$00:Disable,$01:Enable

Main body ECU (Multiplex network body ECU)

  • *: w/ Body Device Voice Recognition Function

(b) Customizing with the multi-display

(1) Turn the ignition switch to ON.

(2) Enter the following menus: Settings / Toyota Prius Vehicle Customize / Utility.

(3) Select the setting by referring to the table below.

Utility

Display

Description

Default

Setting

Relevant ECU

Toyota Prius Vehicle suggestions

Function to enable or disable the display of a message for suggestion service function

ON

ON/While stopped/OFF

Main body ECU (Multiplex network body ECU)

Problem Symptoms Table

PROBLEM SYMPTOMS TABLE

NOTICE:

  • If the power window regulator motor assembly has been replaced with a new one, initialize the power window control system.

    Click here

  • If the main body ECU (multiplex network body ECU) is replaced, refer to Registration.

    Click here

HINT:

  • Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
  • Inspect the fuses and relays related to this system before inspecting the suspected areas below.
Manual Function

Symptom

Suspected Area

Link

Driver side power window does not operate with power window master switch

Proceed to "Driver Side Power Window does not Operate with Power Window Master Switch"

Front passenger side power window does not operate with front passenger side power window switch

Proceed to "Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch"

Rear power window LH does not operate with rear power window switch LH

Proceed to "Rear Power Window LH does not Operate with Rear Power Window Switch LH"

Rear power window RH does not operate with rear power window switch RH

Proceed to "Rear Power Window RH does not Operate with Rear Power Window Switch RH"

Power window inching function operates during driver side power window up operation (approximately 0.4 seconds)

Power window regulator motor assembly LH (for driver door)

Power window inching function operates during front passenger side power window up operation (approximately 0.4 seconds)

Power window regulator motor assembly RH (for front passenger door)

Power window inching function operates during rear power window LH up operation (approximately 0.4 seconds)

Power window regulator motor assembly LH (for rear LH door)

Power window inching function operates during rear power window RH up operation (approximately 0.4 seconds)

Power window regulator motor assembly RH (for rear RH door)

Power window temporarily does not operate

Temporarily overheating of the power window regulator motor assembly

-

Check the installation condition of the power window components

(Power window regulator motor assembly, front door window regulator sub-assembly, door glass, door glass run, etc.)

-

Auto Function

Symptom

Suspected Area

Link

Driver side power window auto up / down function does not operate with power window master switch (manual up / down function is normal)

Proceed to "Driver Side Power Window Auto Up / Down Function does not Operate with Power Window Master Switch"

Front passenger side power window auto up / down function does not operate with front passenger side power window switch (manual up / down function is normal)

Proceed to "Front Passenger Side Power Window Auto Up / Down Function does not Operate with Front Passenger Side Power Window Switch"

Rear power window LH auto up / down function does not operate with rear power window switch LH (manual up / down function is normal)

Proceed to "Rear Power Window LH Auto Up / Down Function does not Operate with Rear Power Window Switch LH"

Rear power window RH auto up / down function does not operate with rear power window switch RH (manual up / down function is normal)

Proceed to "Rear Power Window RH Auto Up / Down Function does not Operate with Rear Power Window Switch RH"

Remote Function (Operation via master switch)

Symptom

Suspected Area

Link

Remote up / down function does not operate (Can be operated via the power window switch of any door)

Proceed to "Remote Up / Down Function does not Operate"

Jam Protection Function

Symptom

Suspected Area

Link

Auto up operation does not fully close power window (jam protection function is activated)

Proceed to "Auto Up Operation does not Fully Close Power Window (Jam Protection Function is Activated)"

Jam protection function does not operate

Proceed to "Jam Protection Function does not Operate"

Catch Protection Function

Symptom

Suspected Area

Link

Auto down operation does not fully open power window (catch protection function is activated

Proceed to "Auto Down Operation does not Fully Open Power Window (Catch Protection Function is Activated)"

Key-off Operation Function

Symptom

Suspected Area

Link

Key-off operation function operates even if operating conditions are not satisfied

Proceed to "Key-off Operation Function Operates even if Operating Conditions are not Satisfied"

Key-off operation function does not operate

Perform initialization

Front door courtesy switch circuit

Rear door courtesy switch circuit

Main body ECU (multiplex network body ECU)

Key-linked Function / Wireless Transmitter-linked Function

Symptom

Suspected Area

Link

All power windows do not operate with driver side door key cylinder or wireless transmitter

Proceed to "All Power Windows do not Operate with Driver Side Door Key Cylinder or Wireless Transmitter"

Suggestion Service Function

Symptom

Suspected Area

Link

Power windows cannot be operated via the suggestion service function

Meter / gauge system

Main body ECU (multiplex network body ECU)

Terminals Of Ecu

TERMINALS OF ECU

CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Driver Door)

(a) Disconnect the O5 power window regulator motor assembly LH (for driver door) connector.

(b) Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

O5-1 (GND) - Body ground

Ground

Always

Below 1 Ω

O5-2 (B) - Body ground

Power supply

Ignition switch off

11 to 14 V

(c) Reconnect the O5 power window regulator motor assembly LH (for driver door) connector.

(d) Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

O5-7 (DOWN) - O5-1 (GND)

Power window motor DOWN input

Ignition switch ON, multiplex network master switch assembly (driver door power window regulator switch) not pushed or not pulled

11 to 14 V

Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) pushed halfway down (Manual operation)

Below 1 V

Ignition switch ON, driver door power window fully closed

11 to 14 V

Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) fully pushed down (Auto operation)

Below 1 V

Ignition switch ON, driver door power window fully open

11 to 14 V

O5-10 (UP) - O5-1 (GND)

Power window motor UP input

Ignition switch ON, multiplex network master switch assembly (driver door power window regulator switch) not pushed or not pulled

11 to 14 V

Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) pulled halfway up (Manual operation)

Below 1 V

Ignition switch ON, multiplex network master switch assembly (driver door power window regulator switch) fully open

11 to 14 V

Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) fully pulled up (Auto operation)

Below 1 V

Ignition switch ON, driver door power window fully closed

11 to 14 V

CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Front Passenger Door)

(a) Disconnect the N4 power window regulator motor assembly RH (for front passenger door) connector.

(b) Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

N4-1 (GND) - Body ground

Ground

Always

Below 1 Ω

N4-2 (B) - Body ground

Power supply

Ignition switch off

11 to 14 V

(c) Reconnect the N4 power window regulator motor assembly RH (for front passenger door) connector.

(d) Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

N4-4 (AUTO) - N4-1 (GND)

Power window motor AUTO UP input

Ignition switch ON, front passenger door power window fully open

11 to 14 V

Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation)

Below 1 V

Ignition switch ON, front passenger door power window fully closed

11 to 14 V

Power window motor AUTO DOWN input

Ignition switch ON, front passenger door power window fully closed

11 to 14 V

Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation)

Below 1 V

Ignition switch ON, front passenger door power window fully open

11 to 14 V

N4-7 (DOWN) - N4-1 (GND)

Power window motor DOWN input

Ignition switch ON, power window regulator switch assembly not pushed or not pulled

11 to 14 V

Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pushed halfway down (Manual operation)

Below 1 V

Ignition switch ON, front passenger door power window fully closed

11 to 14 V

Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation)

Below 1 V

Ignition switch ON, front passenger door power window fully open

11 to 14 V

N4-10 (UP) - N4-1 (GND)

Power window motor UP input

Ignition switch ON, power window regulator switch assembly not pushed or not pulled

11 to 14 V

Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pulled halfway up (Manual operation)

Below 1 V

Ignition switch ON, front passenger door power window fully open

11 to 14 V

Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation)

Below 1 V

Ignition switch ON, front passenger door power window fully closed

11 to 14 V

CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Rear LH Door)

(a) Disconnect the M2 power window regulator motor assembly LH (for rear LH door) connector.

(b) Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

M2-1 (GND) - Body ground

Ground

Always

Below 1 Ω

M2-2 (B) - Body ground

Power supply

Ignition switch off

11 to 14 V

(c) Reconnect the M2 power window regulator motor assembly LH (for rear LH door) connector.

(d) Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

M2-4 (AUTO) - M2-1 (GND)

Power window motor AUTO UP input

Ignition switch ON, rear LH door power window fully open

11 to 14 V

Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pulled up (Auto operation)

Below 1 V

Ignition switch ON, rear LH door power window fully closed

11 to 14 V

Power window motor AUTO DOWN input

Ignition switch ON, rear LH door power window fully closed

11 to 14 V

Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pushed down (Auto operation)

Below 1 V

Ignition switch ON, rear LH door power window fully open

11 to 14 V

M2-7 (DOWN) - M2-1 (GND)

Power window motor DOWN input

Ignition switch ON, rear power window regulator switch assembly (for LH door) not pushed or not pulled

11 to 14 V

Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) pushed halfway down (Manual operation)

Below 1 V

Ignition switch ON, rear LH door power window fully closed

11 to 14 V

Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pushed down (Auto operation)

Below 1 V

Ignition switch ON, rear LH door power window fully open

11 to 14 V

M2-10 (UP) - M2-1 (GND)

Power window motor UP input

Ignition switch ON, rear power window regulator switch assembly (for LH door) not pushed or not pulled

11 to 14 V

Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) pulled halfway up (Manual operation)

Below 1 V

Ignition switch ON, rear LH door power window fully open

11 to 14 V

Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pulled up (Auto operation)

Below 1 V

Ignition switch ON, rear LH door power window fully closed

11 to 14 V

CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Rear RH Door)

(a) Disconnect the L2 power window regulator motor assembly RH (for rear RH door) connector.

(b) Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

L2-1 (GND) - Body ground

Ground

Always

Below 1 Ω

L2-2 (B) - Body ground

Power supply

Ignition switch off

11 to 14 V

(c) Reconnect the L2 power window regulator motor assembly RH (for rear RH door) connector.

(d) Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

L2-4 (AUTO) - L2-1 (GND)

Power window motor AUTO UP input

Ignition switch ON, rear RH door power window fully open

11 to 14 V

Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pulled up (Auto operation)

Below 1 V

Ignition switch ON, rear RH door power window fully closed

11 to 14 V

Power window motor AUTO DOWN input

Ignition switch ON, rear RH door power window fully closed

11 to 14 V

Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pushed down (Auto operation)

Below 1 V

Ignition switch ON, rear RH door power window fully open

11 to 14 V

L2-7 (DOWN) - L2-1 (GND)

Power window motor DOWN input

Ignition switch ON, rear power window regulator switch assembly (for RH door) not pushed or not pulled

11 to 14 V

Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) pushed halfway down (Manual operation)

Below 1 V

Ignition switch ON, rear RH door power window fully closed

11 to 14 V

Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pushed down (Auto operation)

Below 1 V

Ignition switch ON, rear RH door power window fully open

11 to 14 V

L2-10 (UP) - L2-1 (GND)

Power window motor UP input

Ignition switch ON, rear power window regulator switch assembly (for RH door) not pushed or not pulled

11 to 14 V

Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) pulled halfway up (Manual operation)

Below 1 V

Ignition switch ON, rear RH door power window fully open

11 to 14 V

Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pulled up (Auto operation)

Below 1 V

Ignition switch ON, rear RH door power window fully closed

11 to 14 V

CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

(a) Disconnect the O8 multiplex network master switch assembly connector.

(b) Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

O8-1 (B) - O8-4 (GND)

Power supply

Ignition switch off

11 to 14 V

O8-4 (GND) - Body ground

Ground

Always

Below 1 Ω

(c) Reconnect the O8 multiplex network master switch assembly connector.

(d) Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

O8-2 (DOWN) - O8-4 (GND)

Power window motor DOWN output

Ignition switch ON, driver door power window regulator switch not pushed or not pulled

11 to 14 V

Ignition switch ON, driver door power window moving, driver door power window regulator switch pushed halfway down (Manual operation)

Below 1 V

O8-6 (UP) - O8-4 (GND)

Power window motor UP output

Ignition switch ON, driver door power window regulator switch not pushed or not pulled

11 to 14 V

Ignition switch ON, driver door power window moving, driver door power window regulator switch pulled halfway up (Manual operation)

Below 1 V

CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY

(a) Disconnect the N11 power window regulator switch assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

N11-7 (GND) - Body ground

Ground

Always

Below 1 Ω

(c) Reconnect the N11 power window regulator switch assembly connector.

(d) Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

N11-5 (UP) - N11-7 (GND)

Power window motor UP output

Ignition switch ON, power window regulator switch assembly not pushed or not pulled

11 to 14 V

Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pulled halfway up (Manual operation)

Below 1 V

Ignition switch ON, front passenger door power window fully open

11 to 14 V

Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation)

Below 1 V

Ignition switch ON, front passenger door power window fully closed

11 to 14 V

N11-4 (DOWN) - N11-7 (GND)

Power window motor DOWN output

Ignition switch ON, power window regulator switch assembly not pushed or not pulled

11 to 14 V

Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pushed halfway down (Manual operation)

Below 1 V

Ignition switch ON, front passenger door power window fully closed

11 to 14 V

Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation)

Below 1 V

Ignition switch ON, front passenger door power window fully open

11 to 14 V

N11-8 (AUTO) - N11-7 (GND)

Power window motor AUTO UP output

Ignition switch ON, front passenger door power window fully open

11 to 14 V

Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation)

Below 1 V

Ignition switch ON, front passenger door power window fully closed

11 to 14 V

Power window motor AUTO DOWN output

Ignition switch ON, front passenger door power window fully closed

11 to 14 V

Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation)

Below 1 V

Ignition switch ON, front passenger door power window fully open

11 to 14 V

CHECK REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Door)

(a) Disconnect the M3 rear power window regulator switch assembly (for LH door) connector.

(b) Measure the resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

M3-7 (GND) - Body ground

Ground

Always

Below 1 Ω

(c) Reconnect the M3 rear power window regulator switch assembly (for LH door) connector.

(d) Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

M3-5 (UP) - M3-7 (GND)

Power window motor UP output

Ignition switch ON, rear power window regulator switch assembly (for LH door) not pushed or not pulled

11 to 14 V

Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) pulled halfway up (Manual operation)

Below 1 V

Ignition switch ON, rear LH door power window fully open

11 to 14 V

Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pulled up (Auto operation)

Below 1 V

Ignition switch ON, rear LH door power window fully closed

11 to 14 V

M3-4 (DOWN) - M3-7 (GND)

Power window motor DOWN output

Ignition switch ON, rear power window regulator switch assembly (for LH door) not pushed or not pulled

11 to 14 V

Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) pushed halfway down (Manual operation)

Below 1 V

Ignition switch ON, rear LH door power window fully closed

11 to 14 V

Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pushed down (Auto operation)

Below 1 V

Ignition switch ON, rear LH door power window fully open

11 to 14 V

M3-8 (AUTO) - M3-7 (GND)

Power window motor AUTO UP output

Ignition switch ON, rear LH door power window fully open

11 to 14 V

Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pulled up (Auto operation)

Below 1 V

Ignition switch ON, rear LH door power window fully closed

11 to 14 V

Power window motor AUTO DOWN output

Ignition switch ON, rear LH door power window fully closed

11 to 14 V

Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pushed down (Auto operation)

Below 1 V

Ignition switch ON, rear LH door power window fully open

11 to 14 V

CHECK REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Door)

(a) Disconnect the L3 rear power window regulator switch assembly (for RH door) connector.

(b) Measure the resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

L3-7 (GND) - Body ground

Ground

Always

Below 1 Ω

(c) Reconnect the L3 rear power window regulator switch assembly (for RH door) connector.

(d) Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

L3-5 (UP) - L3-7 (GND)

Power window motor UP output

Ignition switch ON, rear power window regulator switch assembly (for RH door) not pushed or not pulled

11 to 14 V

Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) pulled halfway up (Manual operation)

Below 1 V

Ignition switch ON, rear RH door power window fully open

11 to 14 V

Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pulled up (Auto operation)

Below 1 V

Ignition switch ON, rear RH door power window fully closed

11 to 14 V

L3-4 (DOWN) - L3-7 (GND)

Power window motor DOWN output

Ignition switch ON, rear power window regulator switch assembly (for RH door) not pushed or not pulled

11 to 14 V

Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) pushed halfway down (Manual operation)

Below 1 V

Ignition switch ON, rear RH door power window fully closed

11 to 14 V

Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pushed down (Auto operation)

Below 1 V

Ignition switch ON, rear RH door power window fully open

11 to 14 V

L3-8 (AUTO) - L3-7 (GND)

Power window motor AUTO UP output

Ignition switch ON, rear RH door power window fully open

11 to 14 V

Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pulled up (Auto operation)

Below 1 V

Ignition switch ON, rear RH door power window fully closed

11 to 14 V

Power window motor AUTO DOWN output

Ignition switch ON, rear RH door power window fully closed

11 to 14 V

Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pushed down (Auto operation)

Below 1 V

Ignition switch ON, rear RH door power window fully open

11 to 14 V

Data List / Active Test

DATA LIST / ACTIVE TEST

DATA LIST

HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

(a) Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

FR Door Courtesy Switch Status

Front door courtesy light switch assembly (for RH) signal

Close or Open

Close: Front door RH closed

Open: Front door RH open

-

FL Door Courtesy Switch Status

Front door courtesy light switch assembly (for LH) signal

Close or Open

Close: Front door LH closed

Open: Front door LH open

-

D Door P/W Jam Protection Glass Position (Close-1/4)

Margin for jam protection triggering force of window glass within range of fully closed to 1/4 open window glass position

OK or Caution

OK: Normal manual up operation

Caution: Jam detected in the specified range

-

D Door P/W Jam Protection Glass Position (1/4-2/4)

Margin for jam protection triggering force of window glass within range of 1/4 to 1/2 open window glass position

OK or Caution

OK: Normal manual up operation

Caution: Jam detected in the specified range

-

D Door P/W Jam Protection Glass Position (2/4-3/4)

Margin for jam protection triggering force of window glass within range of 1/2 to 3/4 open window glass position

OK or Caution

OK: Normal manual up operation

Caution: Jam detected in the specified range

-

D Door P/W Jam Protection Glass Position (3/4-Open)

Margin for jam protection triggering force of window glass within range of 3/4 to fully open window glass position

OK or Caution

OK: Normal manual up operation

Caution: Jam detected in the specified range

-

P Door P/W Jam Protection Glass Position (Close-1/4)

Margin for jam protection triggering force of window glass within range of fully closed to 1/4 open window glass position

OK or Caution

OK: Normal manual up operation

Caution: Jam detected in the specified range

-

P Door P/W Jam Protection Glass Position (1/4-2/4)

Margin for jam protection triggering force of window glass within range of 1/4 to 1/2 open window glass position

OK or Caution

OK: Normal manual up operation

Caution: Jam detected in the specified range

-

P Door P/W Jam Protection Glass Position (2/4-3/4)

Margin for jam protection triggering force of window glass within range of 1/2 to 3/4 open window glass position

OK or Caution

OK: Normal manual up operation

Caution: Jam detected in the specified range

-

P Door P/W Jam Protection Glass Position (3/4-Open)

Margin for jam protection triggering force of window glass within range of 3/4 to fully open window glass position

OK or Caution

OK: Normal manual up operation

Caution: Jam detected in the specified range

-

RR Door P/W Jam Protection Glass Position (Close-1/4)

Margin for jam protection triggering force of window glass within range of fully closed to 1/4 open window glass position

OK or Caution

OK: Normal manual up operation

Caution: Jam detected in the specified range

-

RR Door P/W Jam Protection Glass Position (1/4-2/4)

Margin for jam protection triggering force of window glass within range of 1/4 to 1/2 open window glass position

OK or Caution

OK: Normal manual up operation

Caution: Jam detected in the specified range

-

RR Door P/W Jam Protection Glass Position (2/4-3/4)

Margin for jam protection triggering force of window glass within range of 1/2 to 3/4 open window glass position

OK or Caution

OK: Normal manual up operation

Caution: Jam detected in the specified range

-

RR Door P/W Jam Protection Glass Position (3/4-Open)

Margin for jam protection triggering force of window glass within range of 3/4 to fully open window glass position

OK or Caution

OK: Normal manual up operation

Caution: Jam detected in the specified range

-

RL Door P/W Jam Protection Glass Position (Close-1/4)

Margin for jam protection triggering force of window glass within range of fully closed to 1/4 open window glass position

OK or Caution

OK: Normal manual up operation

Caution: Jam detected in the specified range

-

RL Door P/W Jam Protection Glass Position (1/4-2/4)

Margin for jam protection triggering force of window glass within range of 1/4 to 1/2 open window glass position

OK or Caution

OK: Normal manual up operation

Caution: Jam detected in the specified range

-

RL Door P/W Jam Protection Glass Position (2/4-3/4)

Margin for jam protection triggering force of window glass within range of 1/2 to 3/4 open window glass position

OK or Caution

OK: Normal manual up operation

Caution: Jam detected in the specified range

-

RL Door P/W Jam Protection Glass Position (3/4-Open)

Margin for jam protection triggering force of window glass within range of 3/4 to fully open window glass position

OK or Caution

OK: Normal manual up operation

Caution: Jam detected in the specified range

-

D Door Power Window AUTO Switch

Driver door power window auto switch

OFF or ON

OFF: Auto up or auto down switch not being operated

ON: Auto up or auto down switch being operated

D-Door Motor output

P Door Power Window AUTO Switch

Front passenger door power window auto switch

OFF or ON

OFF: Auto up or auto down switch not being operated

ON: Auto up or auto down switch being operated

P-Door Motor output

RR Door Power Window AUTO Switch

Rear RH door power window auto switch

OFF or ON

OFF: Auto up or auto down switch not being operated

ON: Auto up or auto down switch being operated

RR-Door Motor output

RL Door Power Window AUTO Switch

Rear LH door power window auto switch

OFF or ON

OFF: Auto up or auto down switch not being operated

ON: Auto up or auto down switch being operated

RL-Door Motor output

D Door Power Window UP Switch

Driver door power window manual up switch

OFF or ON

OFF: Manual up switch not being operated

ON: Manual up switch being operated

D-Door Motor output

P Door Power Window UP Switch

Front passenger door power window manual up switch

OFF or ON

OFF: Manual up switch not being operated

ON: Manual up switch being operated

P-Door Motor output

RR Door Power Window UP Switch

Rear RH door power window manual up switch

OFF or ON

OFF: Manual up switch not being operated

ON: Manual up switch being operated

RR-Door Motor output

RL Door Power Window UP Switch

Rear LH door power window manual up switch

OFF or ON

OFF: Manual up switch not being operated

ON: Manual up switch being operated

RL-Door Motor output

D Door Power Window DOWN Switch

Driver door power window manual down switch

OFF or ON

OFF: Manual down switch not being operated

ON: Manual down switch being operated

D-Door Motor output

P Door Power Window DOWN Switch

Front passenger door power window manual down switch

OFF or ON

OFF: Manual down switch not being operated

ON: Manual down switch being operated

P-Door Motor output

RR Door Power Window DOWN Switch

Rear RH door power window manual down switch

OFF or ON

OFF: Manual down switch not being operated

ON: Manual down switch being operated

RR-Door Motor output

RL Door Power Window DOWN Switch

Rear LH door power window manual down switch

OFF or ON

OFF: Manual down switch not being operated

ON: Manual down switch being operated

RL-Door Motor output

D Door Power Window Initialize Status

Driver door power window initialize status

Initialized or Uninitialized

Display initialization status

-

P Door Power Window Initialize Status

Front passenger door power window initialize status

Initialized or Uninitialized

Display initialization status

-

RR Door Power Window Initialize Status

Rear RH door power window initialize status

Initialized or Uninitialized

Display initialization status

-

RL Door Power Window Initialize Status

Rear LH door power window initialize status

Initialized or Uninitialized

Display initialization status

-

D Door P/W AUTO Switch

Driver door power window auto switch

OFF or ON

OFF: Auto up or auto down switch not being operated

ON: Auto up or auto down switch being operated

Master Switch output

P Door P/W AUTO Switch

Front passenger door power window auto switch

OFF or ON

OFF: Auto up or auto down switch not being operated

ON: Auto up or auto down switch being operated

Master Switch output

RR Door P/W AUTO Switch

Rear RH door power window auto switch

OFF or ON

OFF: Auto up or auto down switch not being operated

ON: Auto up or auto down switch being operated

Master Switch output

RL Door P/W AUTO Switch

Rear LH door power window auto switch

OFF or ON

OFF: Auto up or auto down switch not being operated

ON: Auto up or auto down switch being operated

Master Switch output

P Door P/W UP Switch

Front passenger door power window manual up switch

OFF or ON

OFF: Manual up switch not being operated

ON: Manual up switch being operated

Master Switch output

RR Door P/W UP Switch

Rear RH door power window manual up switch

OFF or ON

OFF: Manual up switch not being operated

ON: Manual up switch being operated

Master Switch output

RL Door P/W UP Switch

Rear LH door power window manual up switch

OFF or ON

OFF: Manual up switch not being operated

ON: Manual up switch being operated

Master Switch output

P Door P/W DOWN Switch

Front passenger door power window manual down switch

OFF or ON

OFF: Manual down switch not being operated

ON: Manual down switch being operated

Master Switch output

RR Door P/W DOWN Switch

Rear RH door power window manual down switch

OFF or ON

OFF: Manual down switch not being operated

ON: Manual down switch being operated

Master Switch output

RL Door P/W DOWN Switch

Rear LH door power window manual down switch

OFF or ON

OFF: Manual down switch not being operated

ON: Manual down switch being operated

Master Switch output

D Door P/W AUTO Switch Failure

Driver door power window auto switch stuck

OFF or ON

OFF: Switch stuck is detected

ON: Switch stuck is not detected

-

P Door P/W AUTO Switch Failure

Front passenger door power window auto switch stuck

OFF or ON

OFF: Switch stuck is detected

ON: Switch stuck is not detected

-

RR Door P/W AUTO Switch Failure

Rear RH door power window auto switch stuck

OFF or ON

OFF: Switch stuck is detected

ON: Switch stuck is not detected

-

RL Door P/W AUTO Switch Failure

Rear LH door power window auto switch stuck

OFF or ON

OFF: Switch stuck is detected

ON: Switch stuck is not detected

-

P Door P/W UP Switch Failure

Front passenger door power window up switch stuck

OFF or ON

OFF: Switch stuck is detected

ON: Switch stuck is not detected

-

RR Door P/W UP Switch Failure

Rear RH door power window manual up switch stuck

OFF or ON

OFF: Switch stuck is detected

ON: Switch stuck is not detected

-

RL Door P/W UP Switch Failure

Rear LH door power window manual up switch stuck

OFF or ON

OFF: Switch stuck is detected

ON: Switch stuck is not detected

-

P Door P/W DOWN Switch Failure

Front passenger door power window manual down switch stuck

OFF or ON

OFF: Switch stuck is detected

ON: Switch stuck is not detected

-

RR Door P/W DOWN Switch Failure

Rear RH door power window manual down switch stuck

OFF or ON

OFF: Switch stuck is detected

ON: Switch stuck is not detected

-

RL Door P/W DOWN Switch Failure

Rear LH door power window manual down switch stuck

OFF or ON

OFF: Switch stuck is detected

ON: Switch stuck is not detected

-

Communication D-Door Motor

Connection status between power window regulator motor assembly LH (for driver door) and main body ECU (multiplex network body ECU)

STOP or OK

STOP: Communication stopped

OK: Normal communication

-

Communication P-Door Motor

Connection status between power window regulator motor assembly RH (for front passenger door) and main body ECU (multiplex network body ECU)

STOP or OK

STOP: Communication stopped

OK: Normal communication

-

Communication RR-Door Motor

Connection status between power window regulator motor assembly RH (for rear RH door) and main body ECU (multiplex network body ECU)

STOP or OK

STOP: Communication stopped

OK: Normal communication

-

Communication RL-Door Motor

Connection status between power window regulator motor assembly LH (for rear LH door) and main body ECU (multiplex network body ECU)

STOP or OK

STOP: Communication stopped

OK: Normal communication

-

Communication Master Switch

Connection status between multiplex network master switch assembly and main body ECU (multiplex network body ECU)

STOP or OK

STOP: Communication stopped

OK: Normal communication

-

Door Key P/W Up Function

Door key linked power window up

Disable or Enable

Customize setting displayed

-

Door Key P/W Down Function

Door key linked power window down

Disable or Enable

Customize setting displayed

-

P/W Down W/ Transmit Function

Wireless transmitter linked power window down

Disable or Enable

Customize setting displayed

-

P/W Operation Buzzer W/ Transmit Function

Power window buzzer answer-back of wireless function

Disable or Enable

Customize setting displayed

-

Window Open Warning Function

Window open warning function (when ignition switch turned to off)

Disable or Enable

Customize setting displayed

-

Power Window Voice Control Function

Status of door window open/close linked voice recognition control.

Disable or Enable

Customize setting displayed

w/ Body Device Voice Recognition Function

Support Service Function

Setting of Suggestion Service

OFF, Parked or ON

Customize setting displayed

-

D Window Auto Up Function

Auto up operation using the multiplex network master switch assembly

Disable or Enable

Customize setting displayed

-

D Window Auto Down Function

Auto down operation using the multiplex network master switch assembly

Disable or Enable

Customize setting displayed

-

P Window Auto Up Function

Auto up operation using the power window regulator switch assembly

Disable or Enable

Customize setting displayed

-

P Window Auto Up by Driver Function

Remote auto up operation using the multiplex network master switch assembly

Disable or Enable

Customize setting displayed

-

P Window Auto Down Function

Auto down operation using the power window regulator switch assembly

Disable or Enable

Customize setting displayed

-

P Window Auto Down by Driver Function

Remote auto down operation using the multiplex network master switch assembly

Disable or Enable

Customize setting displayed

-

RR Window Auto Up Function

Auto up operation using the rear power window regulator switch assembly (for RH door)

Disable or Enable

Customize setting displayed

-

RR Window Auto Up by Driver Function

Remote auto up operation using the multiplex network master switch assembly

Disable or Enable

Customize setting displayed

-

RR Window Auto Down Function

Auto down operation using the rear power window regulator switch assembly (for RH door)

Disable or Enable

Customize setting displayed

-

RR Window Auto Down by Driver Function

Remote auto down operation using the multiplex network master switch assembly

Disable or Enable

Customize setting displayed

-

RL Window Auto Up Function

Auto up operation using the rear power window regulator switch assembly (for LH door)

Disable or Enable

Customize setting displayed

-

RL Window Auto Up by Driver Function

Remote auto up operation using the multiplex network master switch assembly

Disable or Enable

Customize setting displayed

-

RL Window Auto Down Function

Auto down operation using the rear power window regulator switch assembly (for LH door)

Disable or Enable

Customize setting displayed

-

RL Window Auto Down by Driver Function

Remote auto down operation using the multiplex network master switch assembly

Disable or Enable

Customize setting displayed

-

Service Proposals Function

Setting of Suggestion Service (Driver 1)

OFF, Parked or ON

Customize setting displayed

w/ My Settings System

Service Proposals Function

Setting of Suggestion Service (Driver 2)

OFF, Parked or ON

Customize setting displayed

w/ My Settings System

Service Proposals Function

Setting of Suggestion Service (Driver 3)

OFF, Parked or ON

Customize setting displayed

w/ My Settings System

ACTIVE TEST

HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) Perform the Active Test, according to the display on the GTS.

Body Electrical > Main Body > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

D Door Power Window UP

Driver door power window up activate

OFF/ON

-

D Door Power Window DOWN

Driver door power window down activate

OFF/ON

-

P Door Power Window UP

Front passenger door power window up activate

OFF/ON

-

P Door Power Window DOWN

Front passenger door power window down activate

OFF/ON

-

RR Door Power Window UP

Rear RH door power window up activate

OFF/ON

-

RR Door Power Window DOWN

Rear RH door power window down activate

OFF/ON

-

RL Door Power Window UP

Rear LH door power window up activate

OFF/ON

-

RL Door Power Window DOWN

Rear LH door power window down activate

OFF/ON

-

HINT:

Up and down movement does not occur if the arrow is not pressed and held.

Diagnostic Trouble Code Chart

DIAGNOSTIC TROUBLE CODE CHART

Power Window Control System

DTC No.

Detection Item

DTC Output from

Priority

Link

B231200

Master SW Malfunction

Main Body

A

B231D96

D-Door P/W Motor Component Internal Failure

Main Body

A

B231E96

P-Door P/W Motor Component Internal Failure

Main Body

A

B231F96

RR-Door P/W Motor Component Internal Failure

Main Body

A

B232096

RL-Door P/W Motor Component Internal Failure

Main Body

A

VEHICLE CONTROL HISTORY (RoB)

VEHICLE CONTROL HISTORY (RoB)

NOTICE:

  • If the vehicle or vehicle controls are operated (for example, during initial inspection when the vehicle is brought in for repair) before operation history has been read out and saved, the operation history information could be lost.
  • The function "Toyota Prius Vehicle Control History (RoB)" uses the current system time setting inside the GTS and the time counter inside the controlling ECU to calculate the timings shown in the operation history. For this reason, before reading out the operation history, first make sure that the GTS system clock is accurately set to the current time.
  • The time counter in the control ECU may deviate by up to /- 10% due to the characteristics of the time counter.
  • The time counter in the control ECU is reset approximately 34 days before the "Current" value due to the characteristics of the time counter. Therefore, the time information stored before the 34th day may not be accurately displayed.

Toyota Prius Vehicle CONTROL HISTORY (RoB)

HINT:

Vehicle Control History (RoB) : The main body ECU (multiplex network body ECU) records the power window control system operation history, which can be read out using the GTS.

(a) Check the Vehicle Control History (RoB) according to the display on the GTS.

Body Electrical > Main Body > Utility

Toyota Prius Vehicle Control History (RoB)

Code

Item

Item Description

Note

X2306

Power Window Operation

Memorize the factors when the power window operated

Memorize operating means for power window operation

X2307

Power Window Status

Memorize power window operation history

Memorize if any window opens and closes while the ignition switch is off

SYMPTOM SIMULATION

Click here

Master SW Malfunction (B231200)

DESCRIPTION

This DTC is stored when the ECU built into a multiplex network master switch assembly determine that the multiplex network master switch assembly is stuck.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

DTC Output from

Priority

B231200

Master SW Malfunction

  • Multiplex network master switch assembly stuck
  • Multiplex network master switch assembly held in same position for more than 20 seconds

Multiplex network master switch assembly

Main Body

A

NOTICE:

The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly.

Click here

HINT:

If DTC B231200 is not output again after the DTC has been cleared, the DTC was stored due to the switch being held in the same position continuously.

PROCEDURE

  1. CLEAR DTC

(a) Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
NEXT
  1. CHECK FOR DTC

(a) Check for DTCs.

Body Electrical > Main Body > Trouble Codes
Result

Proceed to

B231200 is output

A

B231200 is not output

B

A

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

B

END (DTC WAS STORED DUE TO SWITCH BEING OPERATED FOR 20 SECONDS OR MORE)

D-Door P/W Motor Component Internal Failure (B231D96)

DESCRIPTION

The main body ECU (multiplex network body ECU) communicates with the multiplex network master switch assembly and power window regulator motor assembly LH (for driver door) via LIN communication.

This DTC is stored when a power window regulator motor assembly LH (for driver door) is malfunctioning, or the ECU built into the power window regulator motor assembly LH (for driver door) determines that the fully closed power window position has deviated approximately 20 mm (0.787 in.) or more from the normal position.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

DTC Output from

Priority

B231D96

D-Door P/W Motor Component Internal Failure

  • Either condition is met:
    1. Power window regulator motor assembly (for driver door) is malfunctioning
    2. ECU in power window regulator motor assembly (for driver door) determines that fully closed power window position has deviated approx. 20 mm (0.787 in.) or more from normal position
  • Incorrect installation of power window components
  • Overheated power window regulator motor assembly LH (for driver door)
  • Power window regulator motor assembly LH (for driver door)
  • Wire harness or connector

Main Body

A

WIRING DIAGRAM

NOTICE:

  • Inspect the fuses for circuits related to this system before performing the following procedure.
  • If a power window regulator motor assembly LH (for driver door) has been replaced with a new one, initialize the power window control system.

    Click here

  • If a power window regulator motor assembly LH (for driver door) and door window regulator sub-assembly have been removed and installed, or if a power window regulator motor assembly LH (for driver door) was reused when a door glass or door glass run was replaced, initialize the power window control system.

    Click here

  • The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly.

    Click here

PROCEDURE

  1. CLEAR DTC

(a) Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
NEXT
  1. CHECK FOR DTC

(a) Check for DTCs.

Body Electrical > Main Body > Trouble Codes
Result

Proceed to

B231D96 is output

A

B231D96 is not output

B

B

USE SIMULATION METHOD TO CHECK

A
  1. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Driver Door) - AUXILIARY BATTERY AND BODY GROUND)

Pre-procedure1

(a) Disconnect the O5 power window regulator motor assembly LH (for driver door) connector.

Procedure1

(b) Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:

Click Location & Routing(O5) Click Connector(O5)

Tester Connection

Condition

Specified Condition

Result

O5-2 (B) - Body ground

Ignition switch off

11 to 14 V

V

Standard Resistance:

Click Location & Routing(O5) Click Connector(O5)

Tester Connection

Condition

Specified Condition

Result

O5-1 (GND) - Body ground

Always

Below 1 Ω

Ω

Post-procedure1

(c) None

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. PERFORM ACTIVE TEST USING GTS

(a) Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

D Door Power Window UP

Driver door power window up activate

OFF/ON

-

D Door Power Window DOWN

Driver door power window down activate

OFF/ON

-

Body Electrical > Main Body > Active Test

D Door Power Window UP

Body Electrical > Main Body > Active Test

D Door Power Window DOWN

HINT:

Up and down movement does not occur if the arrow is not pressed and held.

OK:

Driver door power window operates normally.

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Driver Door)

OK
  1. PERFORM INITIALIZATION

(a) Initialize the power window regulator motor assembly LH (for driver door).

Click here

NEXT
  1. CHECK POWER WINDOW CONTROL SYSTEM

(a) Check that the driver door power window operates normally by opening and closing it.

HINT:

Click here

OK:

Driver door power window operates normally.

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Driver Door)

OK
  1. CHECK WHETHER PARTS HAVE BEEN INSTALLED CORRECTLY

(a) Check that the driver door power window components are installed correctly.

OK:

Driver door power window components are installed correctly.

OK

END (OVERHEATED POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Driver Door) WAS DEFECTIVE)

NG

INSTALL PARTS CORRECTLY

P-Door P/W Motor Component Internal Failure (B231E96)

DESCRIPTION

The main body ECU (multiplex network body ECU) communicates with the power window regulator motor assembly RH (for front passenger door) via LIN communication.

This DTC is stored when a power window regulator motor assembly RH (for front passenger door) is malfunctioning, or the ECU built into the power window regulator motor assembly RH (for front passenger door) determines that the fully closed power window position has deviated approximately 20 mm (0.787 in.) or more from the normal position.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

DTC Output from

Priority

B231E96

P-Door P/W Motor Component Internal Failure

  • Either condition is met:
    1. Power window regulator motor assembly (for front passenger door) is malfunctioning
    2. ECU in power window regulator motor assembly (for front passenger door) determines that fully closed power window position has deviated approx. 20 mm (0.787 in.) or more from normal position
  • Incorrect installation of power window components
  • Overheated power window regulator motor assembly RH (for front passenger door)
  • Power window regulator motor assembly RH (for front passenger door)
  • Wire harness or connector

Main Body

A

WIRING DIAGRAM

NOTICE:

  • Inspect the fuses for circuits related to this system before performing the following procedure.
  • If a power window regulator motor assembly RH (for front passenger door) has been replaced with a new one, initialize the power window control system.

    Click here

  • If a power window regulator motor assembly RH (for front passenger door) and door window regulator sub-assembly have been removed and installed, or if a power window regulator motor assembly RH (for front passenger door) was reused when a door glass or door glass run was replaced, initialize the power window control system.

    Click here

  • The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly.

    Click here

PROCEDURE

  1. CLEAR DTC

(a) Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
NEXT
  1. CHECK FOR DTC

(a) Check for DTCs.

Body Electrical > Main Body > Trouble Codes
Result

Proceed to

B231E96 is output

A

B231E96 is not output

B

B

USE SIMULATION METHOD TO CHECK

A
  1. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Front Passenger Door) - AUXILIARY BATTERY AND BODY GROUND)

Pre-procedure1

(a) Disconnect the N4 power window regulator motor assembly RH (for front passenger door) connector.

Procedure1

(b) Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:

Click Location & Routing(N4) Click Connector(N4)

Tester Connection

Condition

Specified Condition

Result

N4-2 (B) - Body ground

Ignition switch off

11 to 14 V

V

Standard Resistance:

Click Location & Routing(N4) Click Connector(N4)

Tester Connection

Condition

Specified Condition

Result

N4-1 (GND) - Body ground

Always

Below 1 Ω

Ω

Post-procedure1

(c) None

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. PERFORM ACTIVE TEST USING GTS

(a) Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

P Door Power Window UP

Front passenger door power window up activate

OFF/ON

-

P Door Power Window DOWN

Front passenger door power window down activate

OFF/ON

-

Body Electrical > Main Body > Active Test

P Door Power Window UP

Body Electrical > Main Body > Active Test

P Door Power Window DOWN

HINT:

Up and down movement does not occur if the arrow is not pressed and held.

OK:

Front passenger door power window operates normally.

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Front Passenger Door)

OK
  1. PERFORM INITIALIZATION

(a) Initialize the power window regulator motor assembly RH (for front passenger door).

Click here

NEXT
  1. CHECK POWER WINDOW CONTROL SYSTEM

(a) Check that the front passenger door power window operates normally by opening and closing it.

HINT:

Click here

OK:

Front passenger door power window operates normally.

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Front Passenger Door)

OK
  1. CHECK WHETHER PARTS HAVE BEEN INSTALLED CORRECTLY

(a) Check that the front passenger door power window components are installed correctly.

OK:

Front passenger door power window components are installed correctly.

OK

END (OVERHEATED POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Front Passenger Door) WAS DEFECTIVE)

NG

INSTALL PARTS CORRECTLY

RR-Door P/W Motor Component Internal Failure (B231F96)

DESCRIPTION

The main body ECU (multiplex network body ECU) communicates with the power window regulator motor assembly RH (for rear RH door) via LIN communication.

This DTC is stored when a power window regulator motor assembly RH (for rear RH door) is malfunctioning, or the ECU built into the power window regulator motor assembly RH (for rear RH door) determines that the fully closed power window position has deviated approximately 20 mm (0.787 in.) or more from the normal position.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

DTC Output from

Priority

B231F96

RR-Door P/W Motor Component Internal Failure

  • Either condition is met:
    1. Power window regulator motor assembly (for rear RH door) is malfunctioning
    2. ECU in power window regulator motor assembly (for rear RH door) determines that fully closed power window position has deviated approx. 20 mm (0.787 in.) or more from normal position
  • Incorrect installation of power window components
  • Overheated power window regulator motor assembly RH (for rear RH door)
  • Power window regulator motor assembly RH (for rear RH door)
  • Wire harness or connector

Main Body

A

WIRING DIAGRAM

NOTICE:

  • Inspect the fuses for circuits related to this system before performing the following procedure.
  • If a power window regulator motor assembly RH (for rear RH door) has been replaced with a new one, initialize the power window control system.

    Click here

  • If a power window regulator motor assembly RH (for rear RH door) and door window regulator sub-assembly have been removed and installed, or if a power window regulator motor assembly RH (for rear RH door) was reused when a door glass or door glass run was replaced, initialize the power window control system.

    Click here

  • The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly.

    Click here

PROCEDURE

  1. CLEAR DTC

(a) Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
NEXT
  1. CHECK FOR DTC

(a) Check for DTCs.

Body Electrical > Main Body > Trouble Codes
Result

Proceed to

B231E96 is output

A

B231E96 is not output

B

B

USE SIMULATION METHOD TO CHECK

A
  1. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Rear RH Door) - AUXILIARY BATTERY AND BODY GROUND)

Pre-procedure1

(a) Disconnect the L2 power window regulator motor assembly RH (for rear RH door) connector.

Procedure1

(b) Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:

Click Location & Routing(L2) Click Connector(L2)

Tester Connection

Condition

Specified Condition

Result

L2-2 (B) - Body ground

Ignition switch off

11 to 14 V

V

Standard Resistance:

Click Location & Routing(L2) Click Connector(L2)

Tester Connection

Condition

Specified Condition

Result

L2-1 (GND) - Body ground

Always

Below 1 Ω

Ω

Post-procedure1

(c) None

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. PERFORM ACTIVE TEST USING GTS

(a) Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

RR Door Power Window UP

Rear RH door power window up activate

OFF/ON

-

RR Door Power Window DOWN

Rear RH door power window down activate

OFF/ON

-

Body Electrical > Main Body > Active Test

RR Door Power Window UP

Body Electrical > Main Body > Active Test

RR Door Power Window DOWN

HINT:

Up and down movement does not occur if the arrow is not pressed and held.

OK:

Rear RH Door power window operates normally.

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Rear RH Door)

OK
  1. PERFORM INITIALIZATION

(a) Initialize the power window regulator motor assembly RH (for rear RH door).

Click here

NEXT
  1. CHECK POWER WINDOW CONTROL SYSTEM

(a) Check that the rear RH door power window operates normally by opening and closing it.

HINT:

Click here

OK:

Rear RH door power window operates normally.

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Rear RH Door)

OK
  1. CHECK WHETHER PARTS HAVE BEEN INSTALLED CORRECTLY

(a) Check that the rear RH door power window components are installed correctly.

OK:

Rear RH door power window components are installed correctly.

OK

END (OVERHEATED POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Rear RH Door) WAS DEFECTIVE)

NG

INSTALL PARTS CORRECTLY

RL-Door P/W Motor Component Internal Failure (B232096)

DESCRIPTION

The main body ECU (multiplex network body ECU) communicates with the power window regulator motor assembly LH (for rear LH door) via LIN communication.

This DTC is stored when a power window regulator motor assembly LJH (for rear LH door) is malfunctioning, or the ECU built into the power window regulator motor assembly LH (for rear LH door) determines that the fully closed power window position has deviated approximately 20 mm (0.787 in.) or more from the normal position.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

DTC Output from

Priority

B232096

RL-Door P/W Motor Component Internal Failure

  • Either condition is met:
    1. Power window regulator motor assembly (for rear LH door) is malfunctioning
    2. ECU in power window regulator motor assembly (for rear LH door) determines that fully closed power window position has deviated approx. 20 mm (0.787 in.) or more from normal position
  • Incorrect installation of power window components
  • Overheated power window regulator motor assembly LH (for rear LH door)
  • Power window regulator motor assembly LH (for rear LH door)
  • Wire harness or connector

Main Body

A

WIRING DIAGRAM

NOTICE:

  • Inspect the fuses for circuits related to this system before performing the following procedure.
  • If a power window regulator motor assembly LH (for rear LH door) has been replaced with a new one, initialize the power window control system.

    Click here

  • If a power window regulator motor assembly LH (for rear LH door) and door window regulator sub-assembly have been removed and installed, or if a power window regulator motor assembly LH (for rear LH door) was reused when a door glass or door glass run was replaced, initialize the power window control system.

    Click here

  • The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly.

    Click here

PROCEDURE

  1. CLEAR DTC

(a) Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
NEXT
  1. CHECK FOR DTC

(a) Check for DTCs.

Body Electrical > Main Body > Trouble Codes
Result

Proceed to

B232096 is output

A

B232096 is not output

B

B

USE SIMULATION METHOD TO CHECK

A
  1. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Rear LH Door) - AUXILIARY BATTERY AND BODY GROUND)

Pre-procedure1

(a) Disconnect the M2 power window regulator motor assembly LH (for rear LH door) connector.

Procedure1

(b) Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:

Click Location & Routing(M2) Click Connector(M2)

Tester Connection

Condition

Specified Condition

Result

M2-2 (B) - Body ground

Ignition switch off

11 to 14 V

V

Standard Resistance:

Click Location & Routing(M2) Click Connector(M2)

Tester Connection

Condition

Specified Condition

Result

M2-1 (GND) - Body ground

Always

Below 1 Ω

Ω

Post-procedure1

(c) None

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. PERFORM ACTIVE TEST USING GTS

(a) Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

RL Door Power Window UP

Rear LH door power window up activate

OFF/ON

-

RL Door Power Window DOWN

Rear LH door power window down activate

OFF/ON

-

Body Electrical > Main Body > Active Test

RL Door Power Window UP

Body Electrical > Main Body > Active Test

RL Door Power Window DOWN

HINT:

Up and down movement does not occur if the arrow is not pressed and held.

OK:

Rear LH door power window operates normally.

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Rear LH Door)

OK
  1. PERFORM INITIALIZATION

(a) Initialize the power window regulator motor assembly LH (for rear LH door).

Click here

NEXT
  1. CHECK POWER WINDOW CONTROL SYSTEM

(a) Check that the rear LH door power window operates normally by opening and closing it.

HINT:

Click here

OK:

Rear LH door power window operates normally.

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Rear LH Door)

OK
  1. CHECK WHETHER PARTS HAVE BEEN INSTALLED CORRECTLY

(a) Check that the rear LH door power window components are installed correctly.

OK:

Rear LH door power window components are installed correctly.

OK

END (OVERHEATED POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Rear LH Door) WAS DEFECTIVE)

NG

INSTALL PARTS CORRECTLY

Remote Up / Down Function does not Operate

DESCRIPTION

When the ignition switch ON, the multiplex network master switch assembly sends remote up and down signals to each power window regulator motor assembly via LIN communication.

NOTICE:

  • If a power window regulator motor assembly has been replaced with a new one, initialize the power window control system.

    Click here

  • The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly.

    Click here

PROCEDURE

  1. PERFORM INITIALIZATION (APPLICABLE LOCATION)

(a) Initialize the power window regulator motor assembly (applicable location).

Click here

NEXT
  1. CHECK POWER WINDOW CONTROL SYSTEM (APPLICABLE LOCATION)

(a) Check that the power window operates normally by opening and closing it (applicable location).

Click here

OK:

Power window operates normally (applicable location).

OK

END (PROBLEM DUE TO INITIALIZATION FAILURE)

NG
  1. READ VALUE USING GTS

(a) Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List

Tester Display

Measurement Item

Normal Condition

Reference Value

Diagnostic Note

P Door P/W AUTO Switch

Front passenger door power window auto switch signal

OFF or ON

OFF: Front passenger door power window auto up or auto down switch not being operated

ON: Front passenger door power window auto up or auto down switch being operated

-

RR Door P/W AUTO Switch

Rear RH door power window auto switch signal

OFF or ON

OFF: Rear RH door power window auto up or auto down switch not being operated

ON: Rear RH door power window auto up or auto down switch being operated

-

RL Door P/W AUTO Switch

Rear LH door power window auto switch signal

OFF or ON

OFF: Rear LH door power window auto up or auto down switch not being operated

ON: Rear LH door power window auto up or auto down switch being operated

-

P Door P/W UP Switch

Front passenger door power window manual up switch signal

OFF or ON

OFF: Front passenger door power window manual up switch not being operated

ON: Front passenger door power window manual up switch being operated

-

RR Door P/W UP Switch

Rear RH door power window manual up switch signal

OFF or ON

OFF: Rear RH door power window manual up switch not being operated

ON: Rear RH door power window manual up switch being operated

-

RL Door P/W UP Switch

Rear LH door power window manual up switch signal

OFF or ON

OFF: Rear LH door power window manual up switch not being operated

ON: Rear LH door power window manual up switch being operated

-

P Door P/W DOWN Switch

Front passenger door power window manual down switch signal

OFF or ON

OFF: Front passenger door power window manual down switch not being operated

ON: Front passenger door power window manual down switch being operated

-

RR Door P/W DOWN Switch

Rear RH door power window manual down switch signal

OFF or ON

OFF: Rear RH door power window manual down switch not being operated

ON: Rear RH door power window manual down switch being operated

-

RL Door P/W DOWN Switch

Rear LH door power window manual down switch signal

OFF or ON

OFF: Rear LH door power window manual down switch not being operated

ON: Rear LH door power window manual down switch being operated

-

Body Electrical > Main Body > Data List

Tester Display

P Door P/W AUTO Switch

RR Door P/W AUTO Switch

RL Door P/W AUTO Switch

P Door P/W UP Switch

RR Door P/W UP Switch

RL Door P/W UP Switch

P Door P/W DOWN Switch

RR Door P/W DOWN Switch

RL Door P/W DOWN Switch

OK:

On the GTS screen, ON or OFF is displayed accordingly.

Result

Proceed to

NG

A

OK (Front passenger door power window remote up and down functions do not operate)

B

OK (Rear LH door power window remote up and down functions do not operate)

C

OK (Rear RH door power window remote up and down functions do not operate)

D

A

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

B

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Front Passenger Door)

C

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door)

D

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH Door)

Driver Side Power Window does not Operate with Power Window Master Switch

DESCRIPTION

When the ignition switch is ON, the power window regulator motor assembly LH (for driver door) is operated by the multiplex network master switch assembly. The power window regulator motor assembly LH (for driver door) has motor, regulator and ECU functions.

WIRING DIAGRAM

Click here

NOTICE:

  • Inspect the fuses for circuits related to this system before performing the following procedure.
  • If the power window regulator motor assembly LH (for driver door) has been replaced with a new one, initialize the power window control system.

    Click here

  • The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly.

    Click here

  • Before replacing the main body ECU (multiplex network body ECU), refer to Registration.

    Click here

PROCEDURE

  1. READ VALUE USING GTS

(a) Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Communication D-Door Motor

Connection status between power window regulator motor assembly LH (for driver door) and main body ECU (multiplex network body ECU)

STOP or OK

STOP: Communication stopped

OK: Normal communication

-

Communication Master Switch

Connection status between multiplex network master switch assembly and main body ECU (multiplex network body ECU)

STOP or OK

STOP: Communication stopped

OK: Normal communication

-

Body Electrical > Main Body > Data List

Tester Display

Communication D-Door Motor

Communication Master Switch

OK:

OK is displayed for each Data List item above.

NG

GO TO LIN COMMUNICATION SYSTEM

OK
  1. READ VALUE USING GTS

(a) Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List

Tester Display

Measurement Item

Normal Condition

Reference Value

Diagnostic Note

D Door Power Window UP Switch

Driver door power window manual up switch

OFF or ON

OFF: Manual up switch not being operated

ON: Manual up switch being operated

-

D Door Power Window DOWN Switch

Driver door power window manual down switch

OFF or ON

OFF: Manual down switch not being operated

ON: Manual down switch being operated

-

Body Electrical > Main Body > Data List

Tester Display

D Door Power Window UP Switch

D Door Power Window DOWN Switch

OK:

On the GTS screen, ON or OFF is displayed accordingly.

NG

GO TO STEP 4

OK
  1. PERFORM ACTIVE TEST USING GTS

(a) Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

D Door Power Window UP

Driver door power window up activate

OFF/ON

-

D Door Power Window DOWN

Driver door power window down activate

OFF/ON

-

Body Electrical > Main Body > Active Test

D Door Power Window UP

Body Electrical > Main Body > Active Test

D Door Power Window DOWN

HINT:

Up and down movement does not occur if the arrow is not pressed and held.

OK:

Driver door power window operates normally.

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Driver Door)

  1. CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

(a) Disconnect the O5 power window regulator motor assembly LH (for driver door) connector.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Click Location & Routing(O5) Click Connector(O5)

Tester Connection

Condition

Specified Condition

O5-10 (UP) - Body ground

Ignition switch ON

11 to 14 V

O5-7 (DOWN) - Body ground

Ignition switch ON

11 to 14 V

NG

GO TO STEP 6

OK
  1. INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Driver Door)

Click here

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Driver Door)

  1. CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Driver Door))

(a) Disconnect the O8 multiplex network master switch assembly connector.

(b) Disconnect the O5 power window regulator motor assembly LH (for driver door) connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(O8,O5) Click Connector(O8) Click Connector(O5)

Tester Connection

Condition

Specified Condition

O8-6 (UP) - O5-10 (UP)

Always

Below 1 Ω

O8-2 (DOWN) - O5-7 (DOWN)

Always

Below 1 Ω

O8-6 (UP) or O5-10 (UP) - Body ground

Always

10 kΩ or higher

O8-2 (DOWN) or O5-7 (DOWN) - Body ground

Always

10 kΩ or higher

OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch

DESCRIPTION

When the ignition switch is ON, the power window regulator motor assembly RH (for front passenger door) is operated by the power window regulator switch assembly. The power window regulator motor assembly RH (for front passenger door) has motor, regulator, and ECU functions.

WIRING DIAGRAM

Click here

NOTICE:

  • Inspect the fuses for circuits related to this system before performing the following procedure.
  • If the power window regulator motor assembly RH (for front passenger door) has been replaced with a new one, initialize the power window control system.

    Click here

  • The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly.

    Click here

  • Check that the window lock switch is off before performing the following procedure.
  • Before replacing the main body ECU (multiplex network body ECU), refer to Registration.

    Click here

PROCEDURE

  1. READ VALUE USING GTS

(a) Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Communication P-Door Motor

Connection status between power window regulator motor assembly RH (for front passenger door) and main body ECU (multiplex network body ECU)

STOP or OK

STOP: Communication stopped

OK: Normal communication

-

Body Electrical > Main Body > Data List

Communication P-Door Motor

OK:

OK is displayed for each Data List item above.

NG

GO TO LIN COMMUNICATION SYSTEM

OK
  1. READ VALUE USING GTS

(a) Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

P Door Power Window UP Switch

Front passenger door power window manual up switch

OFF or ON

OFF: Manual up switch not being operated

ON: Manual up switch being operated

-

P Door Power Window DOWN Switch

Front passenger door power window manual down switch

OFF or ON

OFF: Manual down switch not being operated

ON: Manual down switch being operated

-

Body Electrical > Main Body > Data List

Tester Display

P Window Auto Up Function

P Window Auto Down Function

OK:

On the GTS screen, ON or OFF is displayed accordingly.

NG

GO TO STEP 4

OK
  1. PERFORM ACTIVE TEST USING GTS

(a) Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

P Door Power Window UP

Front passenger door power window up activate

OFF/ON

-

P Door Power Window DOWN

Front passenger door power window down activate

OFF/ON

-

Body Electrical > Main Body > Active Test

P Door Power Window UP

Body Electrical > Main Body > Active Test

P Door Power Window DOWN

HINT:

Up and down movement does not occur if the arrow is not pressed and held.

OK:

Front passenger door power window operates normally.

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Front Passenger Door)

  1. INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY

Click here

NG

REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY

OK
  1. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Front Passenger Door))

(a) Disconnect the N4 power window regulator motor assembly RH (for front passenger door) connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(N11,N4) Click Connector(N11) Click Connector(N4)

Tester Connection

Condition

Specified Condition

N11-5 (UP) - N4-10 (UP)

Always

Below 1 Ω

N11-5 (UP) or N4-10 (UP) - Body ground

Always

10 kΩ or higher

N11-4 (DOWN) - N4-7 (DOWN)

Always

Below 1 Ω

N11-4 (DOWN) or N4-7 (DOWN) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Front Passenger Door)

Click here

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Front Passenger Door)

Rear Power Window RH does not Operate with Rear Power Window Switch RH

DESCRIPTION

When the ignition switch is ON, the power window regulator motor assembly RH (for rear RH door) is operated by the rear power window regulator switch assembly (for RH door). The power window regulator motor assembly RH (for rear RH door) has motor, regulator, and ECU functions.

WIRING DIAGRAM

Click here

NOTICE:

  • Inspect the fuses for circuits related to this system before performing the following procedure.
  • If the power window regulator motor assembly RH (for rear RH door) has been replaced with a new one, initialize the power window control system.

    Click here

  • The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly.

    Click here

  • Check that the window lock switch is off before performing the following procedure.
  • Before replacing the main body ECU (multiplex network body ECU), refer to Registration.

    Click here

PROCEDURE

  1. READ VALUE USING GTS

(a) Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Communication RR-Door Motor

Connection status between power window regulator motor assembly RH (for rear RH door) and main body ECU (multiplex network body ECU)

STOP or OK

STOP: Communication stopped

OK: Normal communication

-

Body Electrical > Main Body > Data List

Communication RR-Door Motor

OK:

OK is displayed for each Data List item above.

NG

GO TO LIN COMMUNICATION SYSTEM

OK
  1. READ VALUE USING GTS

(a) Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

RR Door Power Window UP Switch

Rear RH door power window manual up switch

OFF or ON

OFF: Manual up switch not being operated

ON: Manual up switch being operated

-

RR Door Power Window DOWN Switch

Rear RH door power window manual down switch

OFF or ON

OFF: Manual down switch not being operated

ON: Manual down switch being operated

-

Body Electrical > Main Body > Data List

Tester Display

RR Door Power Window UP Switch

RR Door Power Window DOWN Switch

OK:

On the GTS screen, ON or OFF is displayed accordingly.

NG

GO TO STEP 4

OK
  1. PERFORM ACTIVE TEST USING GTS

(a) Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

RR Door Power Window UP

Rear RH door power window up activate

OFF/ON

-

RR Door Power Window DOWN

Rear RH door power window down activate

OFF/ON

-

Body Electrical > Main Body > Active Test

RR Door Power Window UP

Body Electrical > Main Body > Active Test

RR Door Power Window DOWN

HINT:

Up and down movement does not occur if the arrow is not pressed and held.

OK:

Rear RH Door power window operates normally.

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Rear RH Door)

  1. INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Door)

Click here

NG

REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Door)

OK
  1. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH (for RH Door) - POWER WINDOW REGULATOR MOTOR (for Rear RH Door))

(a) Disconnect the L2 power window regulator motor assembly RH (for rear RH door) connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(L3,L2) Click Connector(L3) Click Connector(L2)

Tester Connection

Condition

Specified Condition

L3-5 (UP) - L2-10 (UP)

Always

Below 1 Ω

L3-4 (DOWN) - L2-7 (DOWN)

Always

Below 1 Ω

L3-5 (UP) or L2-10 (UP) - Body ground

Always

10 kΩ or higher

L3-4 (DOWN) or L2-7 (DOWN) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Rear RH door)

Click here

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Rear RH Door)

Driver Side Power Window Auto Up / Down Function does not Operate with Power Window Master Switch

DESCRIPTION

If the manual up and down functions operate normally but the auto up and down functions do not, the power window control system may be in fail-safe mode.

If power window initialization has not been performed, the auto up and down functions will not operate.

WIRING DIAGRAM

NOTICE:

  • If the power window regulator motor assembly LH (for driver door) has been replaced with a new one, initialize the power window control system.

    Click here

  • The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly.

    Click here

  • Check that power window system customize setting "D Window Auto Up Function" and "D Window Auto Down Function" are set to "Enable" before performing the following procedure.

    Click here

  • After the catch protection function has operated, the auto up function will not operate the first time the power window auto up switch is operated. The auto up function will operate normally after the first power window switch operation.
  • Before replacing the main body ECU (multiplex network body ECU), refer to Registration.

    Click here

HINT:

If the pulse sensor built into the power window regulator motor assembly LH (for driver door) is malfunctioning, the power window control system will enter fail-safe mode. The remote up and down and auto up and down functions cannot be operated during fail-safe mode. However, the power window can be closed by holding the multiplex network master switch assembly at the auto up position, and opened manually by pushing down the multiplex network master switch assembly.

PROCEDURE

  1. READ VALUE USING GTS

(a) Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

D Door P/W AUTO Switch

Driver door power window auto switch signal

OFF or ON

OFF: Driver door power window auto up or auto down switch not being operated

ON: Driver door power window auto up or auto down switch being operated

-

Body Electrical > Main Body > Data List

D Door P/W AUTO Switch

OK:

On the GTS screen, ON or OFF is displayed accordingly.

NG

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

OK
  1. READ VALUE USING GTS

(a) Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

D Door Power Window AUTO Switch

Driver door power window auto switch

OFF or ON

OFF: Auto up or auto down switch not being operated

ON: Auto up or auto down switch being operated

-

Body Electrical > Main Body > Data List

D Door Power Window AUTO Switch

OK:

On the GTS screen, ON or OFF is displayed accordingly.

NG

GO TO STEP 5

OK
  1. PERFORM INITIALIZATION

(a) Initialize the power window regulator motor assembly LH (for driver door).

Click here

NEXT
  1. CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP / DOWN FUNCTION)

(a) Check that the driver door power window moves when the auto up and down functions of the multiplex network master switch assembly are operated.

Click here

OK:

Driver door auto up and down functions are normal.

OK

END (PROBLEM DUE TO INITIALIZATION FAILURE)

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Driver Door)

  1. REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

(a) Replace the multiplex network master switch assembly.

Click here

NEXT
  1. CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP / DOWN FUNCTION)

(a) Check that the driver door power window moves when the auto up and down functions of the multiplex network master switch assembly are operated.

Click here

OK:

Driver door auto up and down functions are normal.

OK

END (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

Front Passenger Side Power Window Auto Up / Down Function does not Operate with Front Passenger Side Power Window Switch

DESCRIPTION

If the manual up and down functions operate normally but the auto up and down functions do not, the power window control system may be in fail-safe mode.

If power window initialization has not been performed, the auto up and down functions will not operate.

WIRING DIAGRAM

Click here

NOTICE:

  • If the power window regulator motor assembly RH (for front passenger door) has been replaced with a new one, initialize the power window control system.

    Click here

  • Check that power window system customize settings "P Window Auto Up Function" and "P Window Auto Down Function" are set to "Enable" before performing the following procedure.

    Click here

  • After the catch protection function has operated, the auto up function will not operate the first time the power window auto up switch is operated. The auto up function will operate normally after the first power window switch operation.
  • Before replacing the main body ECU (multiplex network body ECU), refer to Registration.

    Click here

HINT:

If the pulse sensor built into the power window regulator motor assembly RH (for front passenger door) is malfunctioning, the power window control system will enter fail-safe mode. The remote up and down and auto up and down functions cannot be operated during fail-safe mode. However, the power window can be closed by holding the power window regulator switch assembly at the auto up position, and opened manually by pushing down the power window regulator switch assembly.

PROCEDURE

  1. READ VALUE USING GTS

(a) Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

P Door Power Window AUTO Switch

Front passenger door power window auto switch

OFF or ON

OFF: Auto up or auto down switch not being operated

ON: Auto up or auto down switch being operated

-

Body Electrical > Main Body > Data List

P Door Power Window AUTO Switch

OK:

On the GTS screen, ON or OFF is displayed accordingly.

NG

GO TO STEP 4

OK
  1. PERFORM INITIALIZATION

(a) Initialize the power window regulator motor assembly RH (for front passenger door).

Click here

NEXT
  1. CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP / DOWN FUNCTION)

(a) Check that the front passenger door power window moves when the auto up and down functions of the power window regulator switch assembly are operated.

Click here

OK:

Front passenger door auto up and down functions are normal.

OK

END (PROBLEM DUE TO INITIALIZATION FAILURE)

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Front Passenger Door)

  1. INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY

Click here

NG

REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY

OK
  1. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Front Passenger Door))

(a) Disconnect the N4 power window regulator motor assembly RH (for front passenger door) connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(N11,N4) Click Connector(N11) Click Connector(N4)

Tester Connection

Condition

Specified Condition

N11-8 (AUTO) - N4-4 (AUTO)

Always

Below 1 Ω

N11-8 (AUTO) or N4-4 (AUTO) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Front Passenger Door)

(a) Connect the N4 power window regulator motor assembly RH (for front passenger door) connector.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Click Location & Routing(N11) Click Connector(N11)

Tester Connection

Condition

Specified Condition

N11-8 (AUTO) - Body ground

Ignition switch ON

11 to 14 V

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Front Passenger Door)

Rear Power Window LH Auto Up / Down Function does not Operate with Rear Power Window Switch LH

DESCRIPTION

If the manual up and down functions operate normally but the auto up and down functions do not, the power window control system may be in fail-safe mode.

If power window initialization has not been performed, the auto up and down functions will not operate.

WIRING DIAGRAM

Click here

NOTICE:

  • If the power window regulator motor assembly LH (for rear LH door) has been replaced with a new one, initialize the power window control system.

    Click here

  • Check that power window system customize settings "RL Window Auto Up Function" and "RL Window Auto Down Function" are set to "Enable" before performing the following procedure.

    Click here

  • After the catch protection function has operated, the auto up function will not operate the first time the power window auto up switch is operated. The auto up function will operate normally after the first power window switch operation.
  • Before replacing the main body ECU (multiplex network body ECU), refer to Registration.

    Click here

HINT:

If the pulse sensor built into the power window regulator motor assembly LH (for rear LH door) is malfunctioning, the power window control system will enter fail-safe mode. The remote up and down and auto up and down functions cannot be operated during fail-safe mode. However, the power window can be closed by holding the rear power window regulator switch assembly (for LH door) at the auto up position, and opened manually by pushing down the rear power window regulator switch assembly (for LH door).

PROCEDURE

  1. READ VALUE USING GTS

(a) Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

RL Door Power Window AUTO Switch

Rear LH door power window auto switch

OFF or ON

OFF: Auto up or auto down switch not being operated

ON: Auto up or auto down switch being operated

-

Body Electrical > Main Body > Data List

RL Door Power Window AUTO Switch

OK:

On the GTS screen, ON or OFF is displayed accordingly.

NG

GO TO STEP 4

OK
  1. PERFORM INITIALIZATION

(a) Initialize the power window regulator motor assembly LH (for rear LH door).

Click here

NEXT
  1. CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP / DOWN FUNCTION)

(a) Check that the rear LH door power window moves when the auto up and down functions of the rear power window regulator switch assembly (for LH door) are operated.

Click here

OK:

Rear LH door auto up and down functions are normal.

OK

END (PROBLEM DUE TO INITIALIZATION FAILURE)

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Rear LH Door)

  1. INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Door)

Click here

NG

REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Door)

OK
  1. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Door) - POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Rear LH Door))

(a) Disconnect the M2 power window regulator motor assembly LH (for rear LH door) connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(M3,M2) Click Connector(M3) Click Connector(M2)

Tester Connection

Condition

Specified Condition

M3-8 (AUTO) - M2-4 (AUTO)

Always

Below 1 Ω

M3-8 (AUTO) or M2-4 (AUTO) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Rear LH Door)

(a) Connect the M2 power window regulator motor assembly LH (for rear LH door) connector.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Click Location & Routing(M3) Click Connector(M3)

Tester Connection

Condition

Specified Condition

M3-8 (AUTO) - Body ground

Ignition switch ON

11 to 14 V

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Rear LH Door)

Rear Power Window LH does not Operate with Rear Power Window Switch LH

DESCRIPTION

When the ignition switch is ON, the power window regulator motor assembly LH (for rear LH door) is operated by the rear power window regulator switch assembly (for LH door). The power window regulator motor assembly LH (for rear LH door) has motor, regulator, and ECU functions.

WIRING DIAGRAM

Click here

NOTICE:

  • Inspect the fuses for circuits related to this system before performing the following procedure.
  • If the power window regulator motor assembly LH (for rear LH door) has been replaced with a new one, initialize the power window control system.

    Click here

  • The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly.

    Click here

  • Check that the window lock switch is off before performing the following procedure.
  • Before replacing the main body ECU (multiplex network body ECU), refer to Registration.

    Click here

PROCEDURE

  1. READ VALUE USING GTS

(a) Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Communication RL-Door Motor

Connection status between power window regulator motor assembly LH (for rear LH door) and main body ECU (multiplex network body ECU)

STOP or OK

STOP: Communication stopped

OK: Normal communication

-

Body Electrical > Main Body > Data List

Communication RL-Door Motor

OK:

OK is displayed for each Data List item above.

NG

GO TO LIN COMMUNICATION SYSTEM (Proceed to How to Proceed with Troubleshooting)

OK
  1. READ VALUE USING GTS

(a) Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

RL Door Power Window UP Switch

Rear LH door power window manual up switch

OFF or ON

OFF: Manual up switch not being operated

ON: Manual up switch being operated

-

RL Door Power Window DOWN Switch

Rear LH door power window manual down switch

OFF or ON

OFF: Manual down switch not being operated

ON: Manual down switch being operated

-

Body Electrical > Main Body > Data List

Tester Display

RL Door Power Window UP Switch

RL Door Power Window DOWN Switch

OK:

On the GTS screen, ON or OFF is displayed accordingly.

NG

GO TO STEP 4

OK
  1. PERFORM ACTIVE TEST USING GTS

(a) Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

RL Door Power Window UP

Rear LH door power window up activate

OFF/ON

-

RL Door Power Window DOWN

Rear LH door power window down activate

OFF/ON

-

Body Electrical > Main Body > Active Test

RL Door Power Window UP

Body Electrical > Main Body > Active Test

RL Door Power Window DOWN

HINT:

Up and down movement does not occur if the arrow is not pressed and held.

OK:

Rear LH door power window operates normally.

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Rear LH Door)

  1. INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Door)

Click here

NG

REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Door)

OK
  1. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH (for LH Door) - POWER WINDOW REGULATOR MOTOR (for Rear LH Door))

(a) Disconnect the M2 power window regulator motor assembly LH (for rear LH door) connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(M3,M2) Click Connector(M3) Click Connector(M2)

Tester Connection

Condition

Specified Condition

M3-5 (UP) - M2-10 (UP)

Always

Below 1 Ω

M3-4 (DOWN) - M2-7 (DOWN)

Always

Below 1 Ω

M3-5 (UP) or M2-10 (UP) - Body ground

Always

10 kΩ or higher

M3-4 (DOWN) or M2-7 (DOWN) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Rear LH door)

Click here

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Rear LH Door)

Rear Power Window RH Auto Up / Down Function does not Operate with Rear Power Window Switch RH

DESCRIPTION

If the manual up and down functions operate normally but the auto up and down functions do not, the power window control system may be in fail-safe mode.

If power window initialization has not been performed, the auto up and down functions will not operate.

WIRING DIAGRAM

Click here

NOTICE:

  • If the power window regulator motor assembly RH (for rear RH door) has been replaced with a new one, initialize the power window control system.

    Click here

  • Check that power window system customize settings "RR Window Auto Up Function" and "RR Window Auto Down Function" are set to "ON" before performing the following procedure.

    Click here

  • After the catch protection function has operated, the auto up function will not operate the first time the power window auto up switch is operated. The auto up function will operate normally after the first power window switch operation.
  • Before replacing the main body ECU (multiplex network body ECU), refer to Registration.

    Click here

HINT:

If the pulse sensor built into the power window regulator motor assembly RH (for rear RH door) is malfunctioning, the power window control system will enter fail-safe mode. The remote up and down and auto up and down functions cannot be operated during fail-safe mode. However, the power window can be closed by holding the rear power window regulator switch assembly (for RH door) at the auto up position, and opened manually by pushing down the rear power window regulator switch assembly (for RH door).

PROCEDURE

  1. READ VALUE USING GTS

(a) Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

RR Door Power Window AUTO Switch

Rear RH door power window auto switch

OFF or ON

OFF: Manual down switch not being operated

ON: Manual down switch being operated

-

Body Electrical > Main Body > Data List

RR Door Power Window AUTO Switch

OK:

On the GTS screen, ON or OFF is displayed accordingly.

NG

GO TO STEP 4

OK
  1. PERFORM INITIALIZATION

(a) Initialize the power window regulator motor assembly RH (for rear RH door).

Click here

NEXT
  1. CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP / DOWN FUNCTION)

(a) Check that the rear RH door power window moves when the auto up and down functions of the rear power window regulator switch assembly (for RH door) are operated.

Click here

OK:

Rear RH door auto up and down functions are normal.

OK

END (PROBLEM DUE TO INITIALIZATION FAILURE)

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Rear RH Door)

  1. INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Door)

Click here

NG

REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Door)

OK
  1. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Door) - POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Rear RH Door))

(a) Disconnect the L2 power window regulator motor assembly RH (for rear RH door) connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(L3,L2) Click Connector(L3) Click Connector(L2)

Tester Connection

Condition

Specified Condition

L3-8 (AUTO) - L2-4 (AUTO)

Always

Below 1 Ω

L3-8 (AUTO) or L2-4 (AUTO) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Rear RH Door)

(a) Connect the L2 power window regulator motor assembly RH (for rear RH door) connector.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Click Location & Routing(L3) Click Connector(L3)

Tester Connection

Condition

Specified Condition

L3-8 (AUTO) - Body ground

Ignition switch ON

11 to 14 V

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Rear RH Door)

All Power Windows do not Operate with Driver Side Door Key Cylinder or Wireless Transmitter

DESCRIPTION

Wireless Transmitter-linked Function
  • When a key switch is pushed: 1) the door control receiver receives the wireless door lock signal; 2) the door control receiver sends a signal to the main body ECU (multiplex network body ECU) through the certification ECU (smart key ECU assembly); 3) the main body ECU (multiplex network body ECU) sends the operation permission signal to the power window regulator motor assemblies; and 4) the power window regulator motor assemblies are activated.
Key-linked Function
  • When the driver door key cylinder (key linked switch) is turned and held: 1) the door lock motor receives the signal; 2) the main body ECU (multiplex network body ECU) sends the signal to the power window regulator motor assemblies; and 3) the power window regulator motor assemblies are activated.

NOTICE:

  • These functions are set through customize settings, as they are "Disable" by default.

    Click here

  • The power window control system uses the LIN communication system, CAN communication system and CXPI communication system. Inspect the communication functions by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication systems are functioning properly.

    Click here

  • Before replacing the main body ECU (multiplex network body ECU), refer to Registration.

    Click here

PROCEDURE

  1. CHECK BASIC FUNCTION

(a) Check that the wireless door lock / unlock function operates normally.

Click here

(b) Check that the key-linked lock/unlock function operates normally.

Click here

Result

Proceed to

Wireless door lock/unlock function and key-linked lock/unlock function operate normally

A

Wireless door lock/unlock function does not operate normally

B

Key-linked lock/unlock function does not operate normally

C

B

GO TO WIRELESS DOOR LOCK CONTROL SYSTEM

C

GO TO POWER DOOR LOCK CONTROL SYSTEM

A
  1. CHECK MANUAL UP / DOWN FUNCTION

(a) Check that the manual up and down functions using the multiplex network master switch assembly, power window regulator switch assembly and rear power window regulator switch assemblies can operate all of the power windows.

OK:

Manual up and down functions are normal.

NG

GO TO OTHER PROBLEM (Proceed to Problem Symptoms Table)

OK
  1. CHECK REMOTE UP / DOWN FUNCTION

(a) Check that the remote up and down functions using the multiplex network master switch assembly can operate all of the power windows.

Click here

OK:

Remote up and down functions are normal.

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

GO TO OTHER PROBLEM (Proceed to Problem Symptoms Table)

Key-off Operation Function Operates even if Operating Conditions are not Satisfied

DESCRIPTION

When the front doors are closed, each power window regulator motor assembly can be operated for approximately 45 seconds after the ignition switch is turned from ON to off by receiving operation permission signals from the main body ECU (multiplex network body ECU). However, when approximately 45 seconds have elapsed, or the driver door or front passenger door is opened within approximately 45 seconds of the ignition switch being turned off, the power window regulator motor assemblies stop operating.

During auto operation, when 45 seconds have elapsed and key-off operation is prohibited, the power window will continue operating.

NOTICE:

  • If a power window regulator motor assembly has been replaced with a new one, initialize the power window control system.

    Click here

  • The power window control system uses the LIN communication system and CXPI communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly.

    Click here

  • Before replacing the main body ECU (multiplex network body ECU), refer to Registration.

    Click here

PROCEDURE

  1. CHECK KEY-OFF OPERATION FUNCTION

(a) Check the key-off operation function.

Click here

Result

Proceed to

Power window can be operated even after opening driver door or front passenger door within approximately 45 seconds of ignition switch being turned off

A

Power window can be operated even after approximately 45 seconds have elapsed since ignition switch was turned off (for All Doors)

B

Power window can be operated even after approximately 45 seconds have elapsed since ignition switch was turned off (for Driver Door)

C

Power window can be operated even after approximately 45 seconds have elapsed since ignition switch was turned off (for Front Passenger Door)

D

Power window can be operated even after approximately 45 seconds have elapsed since ignition switch was turned off (for Rear LH Door)

E

Power window can be operated even after approximately 45 seconds have elapsed since ignition switch was turned off (for Rear RH Door)

F

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Driver Door)

D

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Front Passenger Door)

E

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door)

F

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH Door)

A
  1. READ VALUE USING GTS

(a) Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

FR Door Courtesy Switch Status

Front door courtesy light switch assembly (for RH) signal

Close or Open

Close: Front door RH closed

Open: Front door RH open

-

FL Door Courtesy Switch Status

Front door courtesy light switch assembly (for LH) signal

Close or Open

Close: Front door LH closed

Open: Front door LH open

-

Body Electrical > Main Body > Data List

Tester Display

FR Door Courtesy Switch Status

FL Door Courtesy Switch Status

OK:

On the GTS screen, Close or Open is displayed accordingly.

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

GO TO LIGHTING SYSTEM (Proceed to Front Door Courtesy Switch Circuit)

Auto Up Operation does not Fully Close Power Window (Jam Protection Function is Activated)

DESCRIPTION

If a door glass does not slide smoothly or a power window regulator motor assembly or door window regulator sub-assembly does not operate smoothly, the jam protection function may be triggered automatically, resulting in the auto up operation being unable to fully close the power window.

NOTICE:

  • If a power window regulator motor assembly has been replaced with a new one, initialize the power window control system.

    Click here

  • If a power window regulator motor assembly and door window regulator sub-assembly have been removed and installed, or if a power window regulator motor assembly was reused when a door glass or door glass run was replaced, initialize the power window control system.

    Click here

HINT:

This symptom may occur for any of the power windows.

PROCEDURE

  1. PERFORM INITIALIZATION (APPLICABLE LOCATION)

(a) Initialize the power window regulator motor assembly (applicable location).

Click here

NEXT
  1. CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP / DOWN FUNCTION (APPLICABLE LOCATION))

(a) Check that each power window moves when the auto up and down functions of the multiplex network master switch assembly, power window regulator switch assembly or rear power window regulator switch assembly are operated.

Click here

OK:

Auto up and down functions are normal (applicable location).

OK

END (PROBLEM DUE TO INITIALIZATION FAILURE)

NG
  1. CHECK DOOR GLASS SLIDING MOVEMENT (APPLICABLE LOCATION)

(a) Remove the door window regulator.

for Front Door: Click here

for Rear Door: Click here

(b) Install the door glass to the door glass run.

for Front Door: Click here

for Rear Door: Click here

(c) Check if the door window regulator operates smoothly.

(d) Check that the door glass slides smoothly when sliding it up by hand.

NOTICE:

Make sure to perform initialization again.

HINT:

Ensure the following:
  • The door glass fits with the glass run without improper contact or deformation.
  • Foreign matter is not caught in the glass run.
  • The glass run is not misaligned.
  • The belt moulding or roof side rail weatherstrip is not caught.
  • The glass is not tilted and does not catch.

OK:

Door glass slides smoothly.

Result

Proceed to

NG

A

OK (Driver door power window)

B

OK (Front passenger door power window)

C

OK (Rear LH door power window)

D

OK (Rear RH door power window)

E

A

FIT DOOR GLASS CORRECTLY (REMOVE FOREIGN MATTER CAUSING IMPROPER FIT OR REPLACE PARTS)

B

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Driver Door)

C

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Front Passenger Door)

D

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Rear LH Door)

E

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Rear RH Door)

Auto Down Operation does not Fully Open Power Window (Catch Protection Function is Activated)

DESCRIPTION

If a door glass does not slide smoothly or a power window regulator motor assembly or door window regulator sub-assembly does not operate smoothly, the catch protection function may be triggered automatically, resulting in the auto down operation being unable to fully open the power window.

NOTICE:

  • If a power window regulator motor assembly has been replaced with a new one, initialize the power window control system.

    Click here

  • If a power window regulator motor assembly and door window regulator sub-assembly have been removed and installed, or if a power window regulator motor assembly was reused when a door glass or door glass run was replaced, initialize the power window control system.

    Click here

HINT:

This symptom may occur for any of the power windows.

PROCEDURE

  1. PERFORM INITIALIZATION (APPLICABLE LOCATION)

(a) Initialize the power window regulator motor assembly (applicable location).

Click here

NEXT
  1. CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP / DOWN FUNCTION (APPLICABLE LOCATION))

(a) Check that each power window moves when the auto up and down functions of the multiplex network master switch assembly or power window regulator switch assembly or rear power window regulator switch assembly is operated.

Click here

OK:

Auto up and down functions are normal (applicable location).

OK

END (PROBLEM DUE TO INITIALIZATION FAILURE)

NG
  1. CHECK DOOR GLASS SLIDING MOVEMENT (APPLICABLE LOCATION)

(a) Remove the door window regulator.

for Front Door: Click here

for Rear Door: Click here

(b) Install the door glass to the door glass run.

for Front Door: Click here

for Rear Door: Click here

(c) Check if the door window regulator operates smoothly.

(d) Check that the door glass slides smoothly when sliding it up by hand.

NOTICE:

Make sure to perform initialization again.

HINT:

Ensure the following:
  • The door glass fits with the glass run without improper contact or deformation.
  • Foreign matter is not caught in the glass run.
  • The glass run is not misaligned.
  • The belt moulding or roof side rail weatherstrip is not caught.
  • The glass is not tilted and does not catch.

OK:

Door glass slides smoothly.

Result

Proceed to

NG

A

OK (Driver door power window)

B

OK (Front passenger door power window)

C

OK (Rear LH door power window)

D

OK (Rear RH door power window)

E

A

FIT DOOR GLASS CORRECTLY (REMOVE FOREIGN MATTER CAUSING IMPROPER FIT OR REPLACE PARTS)

B

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Driver Door)

C

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Front Passenger Door)

D

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Rear LH Door)

E

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Rear RH Door)

Jam Protection Function does not Operate

DESCRIPTION

This symptom may occur for any of the power windows.

The jam protection function operates within a specified range during the manual up or auto up operation.

NOTICE:

  • If a power window regulator motor assembly has been replaced with a new one, initialize the power window control system.

    Click here

  • If the pulse sensor built into the power window regulator motor assemblies are malfunctioning, the power window control system will enter fail-safe mode. The jam protection function cannot be operated during fail-safe mode.
  • After the jam protection function operates when an auto up or manual up operation is performed, the jam protection function will not operate when the manual up operation is performed again within approximately 4 seconds.

PROCEDURE

  1. PERFORM INITIALIZATION (APPLICABLE LOCATION)

(a) Initialize the power window regulator motor assembly (applicable location).

Click here

NEXT
  1. CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP / DOWN FUNCTION)

(a) Check if the power window auto up and down functions operate normally (applicable location).

Click here

OK:

Auto up and down functions are normal (applicable location).

NG

GO TO OTHER PROBLEM (Proceed to Problem Symptoms Table)

OK
  1. CHECK JAM PROTECTION FUNCTION OPERATING RANGE

(a) Check if the jam protection function operates normally for the applicable power window.

HINT:

The jam protection function will not operate within 4 mm (0.157 in.) of the fully closed position.

OK:

Jam protection function operates normally.

Result

Proceed to

OK

A

NG (Driver door power window)

B

NG (Front passenger door power window)

C

NG (Rear LH door power window)

D

NG (Rear RH door power window)

E

A

END (PROBLEM DUE TO INITIALIZATION FAILURE)

B

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Driver Door)

C

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Front Passenger Door)

D

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Rear LH Door)

E

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Rear RH Door)