Hybrid Vehicle Control Ecu
- Removal
- Installation
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during hybrid vehicle control ECU removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/ReplacedReplaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
Replacement of hybrid Toyota Prius vehicle control ECU |
ECU configuration |
- |
|
Update ECU security key |
Toyota Prius Vehicle Control History (RoB) are stored |
||
Code registration |
Hybrid control system cannot be started |
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.
Click here ![]()
HINT:
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Items for which learning is completed by driving the Toyota Prius vehicleEffect/Inoperative Function when Necessary Procedure not Performed | Necessary Procedure | Link |
|---|---|---|
Front Camera System |
Drive the Toyota Prius vehicle straight ahead at 35 km/h or more for 5 seconds or more. |
Effect/Inoperative Function when Necessary Procedure not Performed | Necessary Procedure | Link |
|---|---|---|
| *1: w/o Power Back Door System *2: w/ Power Back Door System |
||
Power Door Lock Control System*1
|
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. |
|
Power Back Door System*2 |
Reset back door close position |
|
Air Conditioning System |
After the ignition switch is turned to ON, the servo motor standard position is recognized. |
- |

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
PRECAUTION |
- |
- |
- |
|
2 |
BATTERY SERVICE HOLE COVER ASSEMBLY |
58440 |
- |
- |
|
3 |
DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL |
- |
- |
- |
- |
*A |
for M20A-FXS |
- |
- |
*a |
HINT: As the illustration shown is an example, the actual details may differ. |
- |
- |

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
4 |
FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
62311B |
- |
- |
- |
5 |
INSTRUMENT SIDE PANEL RH |
55317A |
- |
- |
- |

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
6 |
FRONT DOOR SCUFF PLATE LH |
67914 |
- |
- |
- |
7 |
COWL SIDE TRIM BOARD LH |
62112 |
- |
- |
- |
8 |
NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY |
55606 |
- |
- |
- |
*A |
w/ Knee Airbag |
- |
- |

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
9 |
LOWER CENTER INSTRUMENT PANEL FINISH PANEL |
55434B |
- |
- |
- |
10 |
LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY |
55406B |
- |
- |
- |
11 |
FRONT DOOR SCUFF PLATE RH |
67913 |
- |
- |
- |
12 |
COWL SIDE TRIM BOARD RH |
62111C |
- |
- |
- |
13 |
NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY |
55607 |
- |
- |
- |
14 |
NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY |
- |
- |
- |
- |
15 |
GLOVE COMPARTMENT DOOR ASSEMBLY |
55550 |
- |
- |
|
16 |
LOWER INSTRUMENT PANEL SUB-ASSEMBLY |
55303B |
- |
- |
- |

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
17 |
HYBRID Toyota Prius Vehicle CONTROL ECU |
89980B |
- |
- |
|
PROCEDURE
1. PRECAUTION
![]() |
Click here |
2. REMOVE BATTERY SERVICE HOLE COVER ASSEMBLY (for M20A-FXS)
![]() |
Click here |
3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
(a) for M20A-FXS:
Click here ![]()
(b) for 2ZR-FXE:
Click here ![]()
4. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Click here ![]()
5. REMOVE INSTRUMENT SIDE PANEL RH
Click here ![]()
6. REMOVE FRONT DOOR SCUFF PLATE LH (w/ Knee Airbag)
Click here ![]()
7. REMOVE COWL SIDE TRIM BOARD LH (w/ Knee Airbag)
Click here ![]()
8. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Knee Airbag)
Click here ![]()
9. REMOVE LOWER CENTER INSTRUMENT PANEL FINISH PANEL
Click here ![]()
10. REMOVE LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
Click here ![]()
11. REMOVE FRONT DOOR SCUFF PLATE RH
(a) Use the same procedure as for the LH side.
Click here ![]()
12. REMOVE COWL SIDE TRIM BOARD RH
(a) Use the same procedure as for the LH side.
Click here ![]()
13. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Click here ![]()
14. REMOVE NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY
Click here ![]()
15. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY
![]() |
Click here |
16. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY
Click here ![]()
17. REMOVE HYBRID Toyota Prius Vehicle CONTROL ECU
![]() |
NOTICE: Do not bend the 2 claws more than necessary. |

(1) Disconnect the 2 hybrid Toyota Prius vehicle control ECU connectors as shown in the illustration.

![]() |
Remove in this Direction |
- |
- |
Installation
INSTALLATION
NOTICE:
- After replacing the hybrid vehicle control ECU, make sure to perform update ECU security key.
- After performing the update ECU security key procedure, make sure to perform the initialization procedure for when the cable has been disconnected and reconnected to the negative (-) auxiliary battery terminal.

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
HYBRID Toyota Prius Vehicle CONTROL ECU |
89981 |
- |
- |
|

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
2 |
LOWER INSTRUMENT PANEL SUB-ASSEMBLY |
55303B |
- |
- |
- |
3 |
GLOVE COMPARTMENT DOOR ASSEMBLY |
55550 |
- |
- |
- |
4 |
NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY |
- |
- |
- |
- |
5 |
NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY |
55607 |
- |
- |
- |
6 |
COWL SIDE TRIM BOARD RH |
62111C |
- |
- |
- |
7 |
FRONT DOOR SCUFF PLATE RH |
67913 |
- |
- |
- |
8 |
LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY |
55406B |
- |
- |
- |
9 |
LOWER CENTER INSTRUMENT PANEL FINISH PANEL |
55434B |
- |
- |
- |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
- |
- |

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
10 |
NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY |
55606 |
- |
- |
- |
11 |
COWL SIDE TRIM BOARD LH |
62112 |
- |
- |
- |
12 |
FRONT DOOR SCUFF PLATE LH |
67914 |
- |
- |
- |
*A |
w/ Knee Airbag |
- |
- |

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
13 |
INSTRUMENT SIDE PANEL RH |
55317A |
- |
- |
- |
14 |
FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
62311B |
- |
- |
- |

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
15 |
NEGATIVE AUXILIARY BATTERY TERMINAL |
- |
- |
- |
- |
16 |
BATTERY SERVICE HOLE COVER ASSEMBLY |
58440 |
- |
- |
|
17 |
ECU CONFIGURATION |
- |
- |
- |
|
18 |
UPDATE ECU SECURITY KEY |
- |
- |
- |
|
19 |
PERFORM REGISTRATION |
- |
- |
- |
|
20 |
INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL |
- |
- |
- |
|
*A |
for M20A-FXS |
- |
- |
PROCEDURE
1. INSTALL HYBRID Toyota Prius Vehicle CONTROL ECU

![]() |
Install in this Direction |
- |
- |

(1) Connect the 2 hybrid Toyota Prius vehicle control ECU connectors as shown in the illustration.
2. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY
Click here ![]()
3. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY
4. INSTALL NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY
5. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
6. INSTALL COWL SIDE TRIM BOARD RH
7. INSTALL FRONT DOOR SCUFF PLATE RH
8. INSTALL LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
9. INSTALL LOWER CENTER INSTRUMENT PANEL FINISH PANEL
10. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Knee Airbag)
11. INSTALL COWL SIDE TRIM BOARD LH (w/ Knee Airbag)
12. INSTALL FRONT DOOR SCUFF PLATE LH (w/ Knee Airbag)
13. INSTALL INSTRUMENT SIDE PANEL RH
14. CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH
15. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
- for M20A-FXS:
Click here

- for 2ZR-FXE:
Click here

16. INSTALL BATTERY SERVICE HOLE COVER ASSEMBLY (for M20A-FXS)
![]() |
Click here |
17. ECU CONFIGURATION
(a) If the hybrid Toyota Prius vehicle control ECU has been replaced, perform ECU configuration.
Click here ![]()
18. UPDATE ECU SECURITY KEY
Click here ![]()
19. PERFORM REGISTRATION
HINT:
After replacing the hybrid Toyota Prius vehicle control ECU, make sure to perform code registration.
Click here ![]()
20. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL
HINT:
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click here
![]()





















































