Front Drive Shaft Assembly

In this manual: Front Drive Shaft Assembly
How To Troubleshoot Ecu Controlled Systems — 1How To Use This Manual — 1Identification Information — 1Repair Instruction — 1Terms — 12zr-fxe Air Cleaner Filter Element — 12zr-fxe Auxiliary Battery — 12zr-fxe Coolant (for Engine Coolant) — 12zr-fxe Oil And Oil Filter — 12zr-fxe Spark Plug — 1Air Conditioning Filter — 1Battery Cooling Filter — 1Brake Fluid — 1Coolant (for Inverter) — 1Front Brake Flexible Hose — 1Front Disc Brake Pad — 1Front Lower Ball Joint — 1Front Wheel Alignment — 1Front Wiper Rubber — 1General Maintenance — 1M20a-fxs Air Cleaner Filter Element — 1M20a-fxs Auxiliary Battery — 1M20a-fxs Coolant (for Engine Coolant) — 1M20a-fxs Oil And Oil Filter — 1M20a-fxs Spark Plug — 1Pa10/pb10/pb12 Hybrid Transaxle Fluid — 1Q810 Hybrid Transaxle Fluid — 1Rear Brake Flexible Hose — 1Rear Disc Brake Pad — 1Rear Wheel Alignment — 1Steering Column — 1Tire And Wheel — 1Transmitter Battery — 1When Disconnecting Or Reconnecting Battery Terminal — 1When Replacing Or Removing/installing Parts — 1Automatic High Beam Main Switch — 1Automatic High Beam System — 1Driver Monitor Camera — 1Driver Monitor Camera System — 1Driver Monitor Ecu — 1Front Camera — 1Front Camera System — 1Front Radar Sensor System — 1Front Side Radar Sensor — 1Front Side Radar Sensor System — 1Millimeter Wave Radar Sensor — 1Utility — 1Advanced Park — 1Advanced Park Main Switch — 1Amplifier Antenna — 1Audio And Visual System — 1Front Door Speaker — 1Instrument Panel Speaker — 1Microphone — 1Noise Filter — 1Pillar Speaker — 1Radio Antenna Cord (for Back Door) — 1Radio Antenna Cord (for Instrument Panel) — 1Radio Antenna Cord (for Roof) — 1Radio Receiver — 1Rear Door Speaker — 1Roof Antenna — 1Stereo Component Amplifier — 1Stereo Jack Adapter Assembly — 1Window Glass Antenna Wire — 1Back-up Battery — 1Dcm(telematics Transceiver) — 1Manual(sos)switch — 1Safety Connect System — 1Telephone And Gps Antenna (for Front Side) — 1Telephone And Gps Antenna (for Roof Side) — 1Telephone And Gps Antenna Cords — 1Garage Door Opener System (for Digital Inner Mirror) — 1Garage Door Opener System (for Ec Inner Mirror) — 1Blind Spot Monitor Sensor — 1Blind Spot Monitor System — 1Clearance Warning Ecu — 1Intuitive Parking Assist System — 1Panoramic View Monitor Switch — 1Panoramic View Monitor System — 1Parking Assist Ecu — 1Parking Assist Light — 1Parking Assist Monitor System — 1Parking Support Brake System — 1Rear View Monitor System — 1Television Camera (for Front) — 1Television Camera (for Rear) — 1Television Camera (for Side) — 1Ultrasonic Sensor (for Front) — 1Ultrasonic Sensor (for Rear) — 1Brake Actuator — 1Brake Pedal Stroke Sensor — 1Electronically Controlled Brake System — 1Front Speed Sensor — 1Rear Speed Sensor (for Awd) — 1Steering Angle Sensor — 1Brake Booster — 1Brake Fluid — 1Brake Line — 1Brake Pedal — 1Brake System — 1Electric Parking Brake Actuator — 1Electric Parking Brake Switch — 1Electric Parking Brake System — 1Forced Release — 1Front Axle Hub — 1Front Axle Hub Bolt — 1Rear Axle Carrier (for 2wd) — 1Rear Axle Carrier (for Awd) — 1Rear Axle Hub (for 2wd) — 1Rear Axle Hub (for Awd) — 1Rear Axle Hub Bolt — 1Steering Knuckle — 1Drive Shaft System — 1Front Drive Shaft Assembly — 1Rear Drive Shaft Assembly — 1Combination Switch — 1Electronic Shift Lever System — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Oil Seal — 1Hybrid Transaxle System — 1Input Shaft Oil Seal — 1Motor Cable — 1Pa10 Hybrid Vehicle Transaxle — 1Pa10 Manual Parking Lock Release — 1Pa10 Oil Cooler — 1Pb10/pb12 Hybrid Vehicle Transaxle — 1Pb10/pb12 Manual Parking Lock Release — 1Pb10/pb12 Oil Cooler — 1Shift Control Actuator — 1Shift Lever — 1Shift Lever Knob — 1Differential Side Gear Shaft — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Side Gear Oil Seal — 1Motor Cable — 1Rear Traction Motor — 1Coolant (for Engine) — 1Cooling Fan Motor — 1Cooling Fan System — 1Radiator — 1Relay — 1Thermostat — 1Water Pump — 1Canister — 1Egr Cooler — 1Egr Valve — 1Emission Control System — 1Fuel Tank Cap — 1Pcv Valve — 1Purge Valve — 1Vacuum Sensor — 1Air Fuel Ratio Sensor — 1Camshaft Oil Control Valve — 1Camshaft Position Sensor — 1Crankshaft Position Sensor — 1Ecm — 1Engine Coolant Temperature Sensor — 1Heated Oxygen Sensor — 1Ignition Coil And Spark Plug — 1Ignition System — 1Knock Sensor — 1Mass Air Flow Meter — 1Relay — 1Sfi System — 1Throttle Body — 1Camshaft — 1Cylinder Block — 1Cylinder Head — 1Cylinder Head Gasket — 1Engine — 1Engine Assembly — 1Engine Unit — 1Front Crankshaft Oil Seal — 1Rear Crankshaft Oil Seal — 1Fuel Filter — 1Fuel Injector — 1Fuel Pressure Regulator — 1Fuel Pump — 1Fuel Sender Gauge Assembly — 1Fuel System — 1Fuel Tank — 1Air Cleaner Filter Element — 1Exhaust Manifold — 1Exhaust Pipe — 1Intake Manifold — 1Intake System — 1Lubrication System — 1Oil And Oil Filter — 1Oil Pan And Oil Level Sensor — 1Oil Pressure Switch — 1Oil Pump — 1Accelerator Pedal Sensor — 1Battery Blower (for Hev Model) — 1Battery Ecu (for Hev Model) — 1Battery Ecu (for Phev Model) — 1Battery Voltage Sensor (for Phev Model) — 1Charge Cable (for Phev Model) — 1Charge Indicator (for Phev Model) — 1Charge Inlet (for Phev Model) — 1Combination Switch — 1Coolant (for Inverter) — 1Cooler (for Phev Model) — 1Electric Vehicle Charger Assembly (for Phev Model) — 1Frame Wire (for Hev Model) — 1Frame Wire (for Phev Model) — 1Heater Relay (for Phev Model) — 1Hv Battery (for Hev Model) — 1Hv Battery (for Phev Model) — 1Hv Battery Heater (for Phev Model) — 1Hv Battery Stack (for Phev Model) — 1Hv Relay Assembly (for Hev Model) — 1Hv Relay Assembly (for Phev Model) — 1Hybrid Battery System (for 2zr-fxe) — 1Hybrid Battery System (for M20a-fxs) — 1Hybrid Battery System (for Phev Model) — 1Hybrid Vehicle Control Ecu — 1Inverter With Converter (for Hev Model) — 1Motor Generator Control System (for 2zr-fxe) — 1Plug-in Charge Control System (for Phev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Service Plug Grip (for Hev Model) — 1Sub Radiator — 1Water Pump With Motor — 1Auxiliary Battery — 1Battery Current Sensor — 1Charging System — 1Solar Charging System — 1Solar Control Unit — 1Solar Roof — 1Can Communication System (for Hev Model) — 1Lin Communication System — 1Network Gateway Ecu — 1Integration Control Supply — 1Main Body Ecu — 1Power Integration System — 1Sub Battery System — 1Power Steering Ecu — 1Power Steering System — 1Heated Steering Wheel Controller — 1Heated Steering Wheel System — 1Steering Column Assembly — 1Steering Heater Switch — 1Steering Pad Switch — 1Steering System — 1Steering Wheel — 1Front Lower Ball Joint — 1Front Lower Suspension Arm (for 2zr-fxe Lh Side) — 1Front Lower Suspension Arm (for 2zr-fxe Rh Side) — 1Front Lower Suspension Arm (for M20a-fxs) — 1Front Shock Absorber — 1Front Stabilizer Bar — 1Front Suspension Member — 1Rear Coil Spring — 1Rear Lower Arm (for Awd Lh Side) — 1Rear Lower Arm (for Awd Rh Side) — 1Rear Lower Arm (for Hev Model 2wd) — 1Rear Lower Arm (for Phev Model) — 1Rear Shock Absorber — 1Rear Stabilizer Bar — 1Rear Suspension Member (for 2wd) — 1Rear Suspension Member (for Awd) — 1Rear Trailing Arm — 1Rear Upper Arm — 1Tire And Wheel System — 1Tire Repair Seal — 1Tire Pressure Warning Receiver — 1Tire Pressure Warning System — 1Tire Pressure Warning Valve — 1Acoustic Vehicle Alerting System — 1Vehicle Approaching Speaker — 1Vehicle Approaching Speaker Ecu — 1Back Door — 1Back Door Closer Ecu — 1Back Door Opener Switch — 1Back Door Support — 1Back Door Weatherstrip — 1Charge Lid Courtesy Switch — 1Charge Lid Opener Motor Assembly — 1Charge Lid Opener System — 1Charge Lid Opener Unit — 1Front Door — 1Front Door Opening Trim Weatherstrip — 1Fuel Lid Opener Motor Assembly — 1Fuel Lid Opener Switch — 1Fuel Lid Opener System — 1Hood — 1Hood Lock Control Cable Assembly — 1Power Back Door Closer Switch — 1Power Back Door Control Switch — 1Power Back Door Drive Unit — 1Power Back Door System — 1Power Back Door Touch Sensor — 1Power Back Door Warning Buzzer — 1Rear Door — 1Rear Door Opening Trim Weatherstrip — 1Reserve Lock Switch — 1Front Bumper — 1Front Door Belt Moulding — 1Front Door Window Frame Moulding — 1Front Fender — 1Front Pillar Upper Cover — 1Grille Shutter — 1Grille Shutter System — 1Name Plate — 1Quarter Garnish — 1Rear Bumper — 1Rear Door Belt Moulding — 1Rear Door Window Frame Moulding — 1Rear Wheel House Plate — 1Rocker Panel Moulding — 1Roof Drip Side Finish Moulding — 1Roof Garnish — 1Wheel Opening Moulding (for Front Side) — 1Wheel Opening Moulding (for Rear Side) — 1Windshield Outside Moulding — 1Horn — 1Horn System — 1Relay — 1Automatic Light Control Sensor — 1Back-up Light Assembly — 1Charge Lid Light — 1Front Marker Light — 1Hazard Warning Switch — 1Headlight Assembly — 1Headlight Dimmer Switch — 1Headlight Leveling Switch — 1High Mounted Stop Light Assembly — 1Illumination Light Assembly — 1License Plate Light Assembly — 1Lighting System — 1Rear Combination Light Assembly — 1Rear Light Assembly — 1Rear Side Marker Light Assembly — 1Relay — 1Side Turn Signal Light Assembly — 1Stop Light Switch — 1Switch Housing — 1Outer Mirror Switch — 1Outer Rear View Mirror — 1Outer Rear View Mirror Cover — 1Outer Rear View Mirror Glass — 1Power Mirror Control System — 1Back Door Glass — 1Front Passenger Side Power Window Switch — 1Power Window Control System — 1Power Window Master Switch — 1Power Window Regulator Motor (for Front Door) — 1Power Window Regulator Motor (for Rear Door) — 1Rear Power Window Switch — 1Relay — 1Roof Window Fix Glass — 1Window Defogger System — 1Windshield Deicer Switch — 1Windshield Deicer System — 1Windshield Glass — 1Front Wiper Motor — 1Rain Sensor — 1Relay — 1Washer Motor — 1Washer Nozzle (for Front Side) — 1Washer Nozzle (for Rear Television Camera) — 1Wiper And Washer System — 1Wiper Ecu — 1Wiper Switch — 1Back Door Lock — 1Door Control Receiver — 1Door Control Switch — 1Door Control Transmitter — 1Door Lock Release Motor (for Rear Side) — 1Door Outside Handle (for Rear Side) — 1Front Door Lock — 1Power Door Lock Control System — 1Rear Door Lock — 1Transmitter Battery — 1Wireless Door Lock Control System — 1Accumulator — 1Air Conditioning Amplifier — 1Air Conditioning Panel — 1Air Conditioning Pressure Sensor — 1Air Conditioning Unit — 1Ambient Temperature Sensor — 1Blower Unit — 1Condenser (for Hev Model) — 1Condenser (for Phev Model) — 1Discharge Temperature Sensor — 1Electric Expansion Valve (cooling) — 1Electric Expansion Valve (heating) — 1Evaporator Pipe Temperature Sensor — 1Evaporator Pressure Regulator — 1Front Blower Motor — 1Front Evaporator Front Solenoid Valve — 1Air Conditioning System (for Hev Model) — 1Front Evaporator Temperature Sensor — 1Heat Exchanger Temperature Sensor — 1Heat Pump Ecu — 1High Pressure Magnetic Valve — 1Humidity Sensor — 1Internal Condenser Temperature Sensor — 1Low Pressure Magnetic Valve — 1Refrigerant (for Hfc-134a(r134a)) — 1Refrigerant Line (for Hev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Room Temperature Sensor — 1Solar Sensor — 1Floor Carpet — 1Front Console Box — 1Instrument Panel Safety Pad — 1Roof Headlining — 1Roof Sunshade — 1Ambient Light (for Driver Side) — 1Ambient Light (for Front Passenger Side) — 1Back Door Courtesy Switch — 1Footwell Light — 1Glove Box Light — 1Lighting System — 1Luggage Compartment Room Light — 1Personal Light — 1Room Light — 1Vanity Light — 1Vanity Light Switch — 1Combination Meter — 1Meter / Gauge System — 1Trip Switch — 1Digital Inner Mirror — 1Digital Rear-view Mirror System — 1Inner Mirror Monitor Camera — 1Inner Rear View Mirror (w/o Ec Mirror) — 1Accessory Power Outlet System — 1Power Outlet Socket (for Console Box Front Side) — 1Power Outlet Socket (for Console Box Rear Side) — 1Power Outlet Socket (for Console Box) — 1Power Outlet Socket (for Luggage Compartment) — 1Power Outlet Switch — 1Wireless Charger Assembly — 1Wireless Charging System — 1Climate Control Seat System — 1Front Power Seat Control System (w/ Memory) — 1Front Power Seat Motor Assembly — 1Front Seat Assembly (for Power Seat) — 1Front Seat Cushion Heater (for Power Seat) — 1Front Seatback Heater (for Power Seat) — 1Lumbar Support Adjuster Assembly — 1Power Seat Control Ecu — 1Power Seat Switch — 1Power Seat Track Rail Assembly — 1Rear Seat Assembly — 1Rear Seat Cushion Heater — 1Rear Seat Reminder System — 1Rear Seatback Heater — 1Seat Heater Control — 1Seat Heater Switch (for Front Seat) — 1Seat Heater Switch (for Rear Side) — 1Seat Heater System — 1Seat Memory Switch — 1Child Restraint Seat Anchor Bracket — 1Front Seat Inner Belt Assembly — 1Front Seat Outer Belt Assembly — 1Occupant Detection Sensor (for Front Passenger Side) — 1Rear Center Seat Outer Belt Assembly — 1Rear Seat Inner Belt Assembly (for Rh Side) — 1Rear Seat Outer Belt Assembly — 1Seat Belt Warning System (w/ Occupant Classification System) — 1Tongue Plate Stopper — 1Airbag System — 1Center Airbag Sensor Assembly — 1Curtain Shield Airbag Assembly — 1Front Airbag Sensor — 1Front Passenger Airbag Assembly — 1Front Seat Side Airbag Assembly — 1Inspection After Collision — 1Knee Airbag Assembly — 1Occupant Classification System — 1Rear Seat Side Airbag Assembly — 1Side Airbag Sensor (for Center Pillar) — 1Side Airbag Sensor (for Front Door) — 1Spiral Cable — 1Steering Pad — 1Certification Ecu — 1Digital Key Ecu — 1Digital Key Receiver (for Front Floor) — 1Digital Key Receiver (for Outside Luggage Compartment) — 1Digital Key Receiver (for Rear Door) — 1Digital Key System — 1Electrical Key Oscillator (for Front Floor) — 1Electrical Key Oscillator (for Outside Luggage Compartment) — 1Electrical Key Oscillator (for Rear Floor) — 1Engine Hood Courtesy Switch — 1Id Code Box — 1Smart Key System (for Start Function) — 1
~23min read
6special tools
070140210280350216159N·mlb·ft
Tightening torque found on this page
  • Removal
  • Disassembly
  • Inspection
  • Reassembly
  • Installation

Removal

REMOVAL

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front drive shaft assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

*1: Also necessary after performing a tire rotation.

*2: It is not necessary to perform this procedure if the tire pressure warning valve and transmitters are installed to the same location.

*3: The Toyota Prius vehicle height changes because of tire replacement.

Front wheel alignment adjustment

Perform "Calibration"

  • DTCs are stored
  • ABS warning light illuminates
  • Brake system warning light (yellow indicator) illuminates
  • Slip indicator light illuminates
  • Electronically controlled brake system disabled or malfunctions

Suspension parts

Rear television camera assembly optical axis (Back camera position setting)

Parking Assist Monitor System

Parking assist ECU initialization

Panoramic View Monitor System

Advanced Park

Tires

  • Initialization*1*2
  • Tire Position Identification*1*2

Tire Pressure Warning System

Refer to Procedures Necessary When Replacing Parts (for Tire Pressure Warning System) table below

Rear television camera assembly optical axis (Back camera position setting)*3

Parking Assist Monitor System

Parking assist ECU initialization*3

Panoramic View Monitor System

Advanced Park

HINT:

  • Use the same procedure for the RH side and LH side.
  • The following procedure is for the LH side.
COMPONENTS (REMOVAL)

Procedure

Part Name Code

1

FRONT WHEELS

-

-

-

-

2

NO. 1 ENGINE UNDER COVER ASSEMBLY

51410

-

-

-

3

REAR ENGINE UNDER COVER LH

51444A

-

-

4

REAR ENGINE UNDER COVER RH

51443C

-

-

-

5

HYBRID TRANSAXLE FLUID

-

-

-

Procedure

Part Name Code

6

FRONT AXLE SHAFT NUT

43502H

-

-

7

FRONT SPEED SENSOR

89543

-

-

8

TIE ROD END SUB-ASSEMBLY

45047

-

-

9

FRONT STABILIZER LINK ASSEMBLY

48810

-

-

10

FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY

48069

-

-

-

11

FRONT DRIVE SHAFT ASSEMBLY

43420

-

-

*1

FRONT FLEXIBLE HOSE

*2

FRONT AXLE ASSEMBLY

*3

COTTER PIN

-

-

●

Non-reusable part

-

-

Procedure

Part Name Code

12

FRONT DRIVE SHAFT ASSEMBLY

43420

-

-

13

FRONT DRIVE SHAFT HOLE SNAP RING

43420G

-

-

-

●

Non-reusable part

-

-

PROCEDURE

1. REMOVE FRONT WHEELS

Click here

2. REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

for M20A-FXS: Click here

for 2ZR-FXE: Click here

3. REMOVE REAR ENGINE UNDER COVER LH

  • Use the same procedure as for the RH side.

    for M20A-FXS: Click here

    for 2ZR-FXE: Click here

4. REMOVE REAR ENGINE UNDER COVER RH

for M20A-FXS: Click here

for 2ZR-FXE: Click here

5. DRAIN HYBRID TRANSAXLE FLUID

Click here

6. REMOVE FRONT AXLE SHAFT NUT

(1) Using SST and a hammer, release the staked part of the front axle shaft nut.

SST: 09930-00010

NOTICE:

Loosen the staked part of the front axle shaft nut completely, otherwise the threads of the drive shaft may be damaged.

(2) While applying the brakes, remove the front axle shaft nut.

7. SEPARATE FRONT SPEED SENSOR

Click here

8. SEPARATE TIE ROD END SUB-ASSEMBLY

Click here

9. SEPARATE FRONT STABILIZER LINK ASSEMBLY

Click here

10. SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY

Click here

11. SEPARATE FRONT DRIVE SHAFT ASSEMBLY

Click here

12. REMOVE FRONT DRIVE SHAFT ASSEMBLY

(1) Using SST, remove the front drive shaft assembly.

SST: 09520-01011

SST: 09520-20010

09521-02010

09521-02040

09521-02060

NOTICE:

  • Do not damage the front drive shaft oil seal.
  • Do not damage the front axle inboard joint boot.
  • Do not drop the front drive shaft assembly.

13. REMOVE FRONT DRIVE SHAFT HOLE SNAP RING

Disassembly

DISASSEMBLY

NOTICE:

  • Secure the drive shaft in a vise between aluminum plates.
  • Do not overtighten the vise.

HINT:

  • Use the same procedure for the RH side and LH side.
  • The following procedure is for the LH side.
COMPONENTS (DISASSEMBLY)

Procedure

Part Name Code

1

FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP

43448G

-

-

2

FRONT AXLE INBOARD JOINT BOOT CLAMP

43448F

-

-

3

FRONT AXLE INBOARD JOINT BOOT

-

-

-

-

4

FRONT DRIVE INBOARD JOINT ASSEMBLY

43040

-

-

5

FRONT DRIVE SHAFT DAMPER CLAMP

43474G

-

-

6

FRONT DRIVE SHAFT DAMPER

43474E

-

-

-

*1

TRIPOD JOINT

*2

FRONT AXLE INBOARD JOINT GROMMET

*3

FRONT DRIVE OUTBOARD JOINT SHAFT ASSEMBLY

*4

SHAFT SNAP RING

●

Non-reusable part

-

-

Procedure

Part Name Code

7

FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP

43447F

-

-

8

FRONT AXLE OUTBOARD JOINT BOOT CLAMP

43447E

-

-

9

FRONT AXLE OUTBOARD JOINT BOOT

-

-

-

*A

for LH Side

-

-

*1

FRONT DRIVE OUTBOARD JOINT SHAFT ASSEMBLY

-

-

●

Non-reusable part

-

-

PROCEDURE

1. SEPARATE FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP

(1) Using a screwdriver, release the staked part of the front No. 2 axle inboard joint boot clamp and separate the front No. 2 axle inboard joint boot clamp.

2. SEPARATE FRONT AXLE INBOARD JOINT BOOT CLAMP

(a) Perform the same procedure as for the front No. 2 axle inboard joint boot clamp.

3. SEPARATE FRONT AXLE INBOARD JOINT BOOT

4. REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY

*a

Matchmark

-

-

(1) Remove the old grease from the front drive inboard joint assembly.

(2) Put matchmarks on the front drive inboard joint assembly and front drive outboard joint shaft assembly.

NOTICE:

Do not use a punch for the marks.

(3) Remove the front drive inboard joint assembly from the front drive outboard joint shaft assembly.

(4) Using a snap ring expander, remove the shaft snap ring from the front drive outboard joint shaft assembly.

(5) Put matchmarks on the front drive outboard joint shaft assembly and tripod joint.

NOTICE:

Do not use a punch for the marks.

(6) Using a brass bar and a hammer, tap out the tripod joint from the front drive outboard joint shaft assembly.

NOTICE:

  • Do not tap the rollers.
  • Do not drop the tripod joint.

(7) Remove the front No. 2 axle inboard joint boot clamp, front drive inboard joint boot and front axle inboard joint boot clamp.

(8) Remove the front axle inboard joint grommet from the front drive inboard joint assembly.

5. REMOVE FRONT DRIVE SHAFT DAMPER CLAMP

*a

Claw

-

-

(1) Using needle-nose pliers, separate the 2 front drive shaft damper clamps.

6. REMOVE FRONT DRIVE SHAFT DAMPER

7. SEPARATE FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP (for LH Side)

(1) Using a screwdriver, release the staked part of the front No. 2 axle outboard joint boot clamp and separate the front No. 2 axle outboard joint boot clamp.

8. SEPARATE FRONT AXLE OUTBOARD JOINT BOOT CLAMP (for LH Side)

(a) Perform the same procedure as for the front No. 2 axle outboard joint boot clamp.

9. REMOVE FRONT AXLE OUTBOARD JOINT BOOT (for LH Side)

(1) Remove the front axle outboard joint boot clamp, front axle outboard joint boot and front No. 2 axle outboard joint boot clamp from the front drive outboard joint shaft assembly.

(2) Remove the old grease from the front drive outboard joint shaft assembly.

Inspection

INSPECTION

PROCEDURE

1. INSPECT FRONT DRIVE SHAFT ASSEMBLY

(a) Check that there is no excessive play in the radial direction of the outboard joint.

(b) Check that the inboard joint slides smoothly in the thrust direction.

(c) Check that there is no excessive play in the radial direction of the inboard joint.

(d) Check the boots for damage.

(e) Check whether each drive shaft dimension (A) is within specification.

NOTICE:

Keep the drive shaft assembly level during inspection.

Dimension (A) (for M20A-FXS):

Installation Position

Specified Condition

Result

for LH Side

587.2 to 595.2 mm

1.93 to 1.95 ft.

mm

ft.

for RH Side

891.2 to 899.2 mm

2.92 to 2.95 ft.

mm

ft.

Dimension (A) (for 2ZR-FXE):

Installation Position

Specified Condition

Result

for LH Side

592.2 to 600.2 mm

1.94 to 1.97 ft.

mm

ft.

for RH Side

891.2 to 899.2 mm

2.92 to 2.95 ft.

mm

ft.

Reassembly

REASSEMBLY

NOTICE:

  • Secure the drive shaft in a vise between aluminum plates.
  • Do not overtighten the vise.

HINT:

  • Use the same procedure for the RH side and LH side.
  • The following procedure is for the LH side.
COMPONENTS (REASSEMBLY)

Procedure

Part Name Code

1

FRONT AXLE OUTBOARD JOINT BOOT

-

-

-

2

FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP

43447F

-

-

3

FRONT AXLE OUTBOARD JOINT BOOT CLAMP

43447E

-

-

*A

for LH Side

-

-

*1

FRONT DRIVE OUTBOARD JOINT SHAFT ASSEMBLY

-

-

●

Non-reusable part

-

-

Procedure

Part Name Code

4

FRONT DRIVE SHAFT DAMPER

43474E

-

-

5

FRONT DRIVE SHAFT DAMPER CLAMP

43474G

-

-

6

FRONT DRIVE INBOARD JOINT ASSEMBLY

43040

-

-

7

FRONT AXLE INBOARD JOINT BOOT

-

-

-

8

FRONT AXLE INBOARD JOINT BOOT CLAMP

43448F

-

-

9

FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP

43448G

-

-

10

INSPECT FRONT DRIVE SHAFT ASSEMBLY

43420

-

-

*1

TRIPOD JOINT

*2

FRONT AXLE INBOARD JOINT GROMMET

*3

FRONT DRIVE OUTBOARD JOINT SHAFT ASSEMBLY

*4

SHAFT SNAP RING

●

Non-reusable part

-

-

PROCEDURE

1. INSTALL FRONT AXLE OUTBOARD JOINT BOOT (for LH Side)

Outboard Joint Side

Inboard Joint Side

Parts insertion direction

Grease

(1) Wrap the splines of the front drive outboard joint shaft assembly with protective tape to prevent the boot from being damaged.

(2) Install new parts to the front drive outboard joint shaft assembly in the following order:

1. Front No. 2 axle outboard joint boot clamp

2. Front axle outboard joint boot

3. Front axle outboard joint boot clamp

(3) Pack the joint portion of the front drive outboard joint shaft assembly and front axle outboard joint boot with grease.

Standard Grease Capacity:

135 to 145 g (4.76 to 5.11 oz.)

(4) Install the front axle outboard joint boot to the front drive outboard joint shaft assembly groove.

NOTICE:

  • Do not allow grease to adhere to the boot clamp track of the outboard joint boot.
  • Keep the inside of the outboard joint boot free of foreign matter.

2. INSTALL FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP (for LH Side)

CAUTION:

  • When installing the front No. 2 axle outboard joint boot clamp, do not perform the work without wearing protective gloves.
  • If work is performed without using protective gloves, injuries may occur.

*a

Fulcrum Point

*b

Lever Push Position

*c

Band Support Position

-

-

(1) Install the front No. 2 axle outboard joint boot clamp to the front axle outboard joint boot and temporarily fold back the lever at the fulcrum point.

NOTICE:

  • Set the lever to the guide groove correctly and install the clamp as far to the inside of the Toyota Prius vehicle as possible.
  • Check the band and the lever for any deformation before folding back the lever.
  • The lever folds easily at the fulcrum point when pushed at the position shown in the illustration.
  • When folding back the lever, do not push at the end of the lever.

    *a

    Temporary Claw

    -

    -

  • If the lever bends in the middle, it may not engage with the temporary claws or may not be held in the correct position.

*a

Press down

*b

Contact Point

*c

Turn

*d

Temporary Claw

*e

Fulcrum Point

-

-

(1) As shown in the illustration, while pressing the outboard joint area against the work surface, firmly press the lever into place by rolling the outboard joint area forward from the folded fulcrum point to the temporary claw area until a click sound is heard.

NOTICE:

  • Do not damage the deflector.
  • Make sure that the outboard joint is in direct contact with the work surface.

*a

Buckle

-

-

(1) Using a plastic hammer, tap the buckle to secure it while adjusting the clearance between the lever and the groove to make the clearance between the buckle edge and the lever end even.

NOTICE:

  • Do not use excessive force when tapping with the plastic hammer.
  • Do not damage the front axle outboard joint boot.

3. INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP (for LH Side)

CAUTION:

  • When installing the front axle outboard joint boot clamp, do not perform the work without wearing protective gloves.
  • If work is performed without using protective gloves, injuries may occur.

*a

Place the tip near the center of the lever

*b

Buckle

(1) Install the front axle outboard joint boot clamp to the front axle outboard joint boot and provisionally bend the lever.

NOTICE:

  • Make sure that the front axle outboard joint boot clamp is correctly positioned within the groove.
  • Confirm that the front axle outboard joint boot clamp and lever are not deformed or damaged.

(2) Using water pump pliers, temporarily secure the front axle outboard joint boot clamp by pinching the front axle outboard joint boot clamp until a click sound is heard.

NOTICE:

Do not damage the front axle outboard joint boot.

(3) Using a plastic hammer, tap the buckle to fix it while adjusting the clearance between the lever and groove to make the clearances between the buckle edge and lever end even.

NOTICE:

  • Do not use excessive force when tapping with the plastic hammer.
  • Do not damage the front axle outboard joint boot.

4. INSTALL FRONT DRIVE SHAFT DAMPER

(1) Temporarily install the front drive shaft damper and 2 new front drive shaft damper clamps to the front drive outboard joint shaft assembly as shown in the illustration.

Dimension (A) (for M20A-FXS):

for LH Side

211.7 to 215.7 mm (8.33 to 8.49 in.)

for RH Side

488 to 492 mm (1.60 to 1.61 ft.)

Dimension (A) (for 2ZR-FXE):

for LH Side

243.4 to 247.4 mm (9.58 to 9.74 in.)

for RH Side

488 to 492 mm (1.60 to 1.61 ft.)

5. INSTALL FRONT DRIVE SHAFT DAMPER CLAMP

*a

Claw

-

-

(1) Using needle-nose pliers, install the 2 front drive shaft damper clamps as shown in the illustration.

NOTICE:

  • Be sure to install the clamps in the correct position.
  • Do not damage the front drive shaft damper.

6. INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY

*a

Matchmark

*b

Groove

Outboard Joint Side

Inboard Joint Side

Install in this Direction

Grease

(1) Install new parts to the front drive outboard joint shaft assembly in the following order:

1. Front axle inboard joint boot clamp

2. Front axle inboard joint boot

3. Front No. 2 axle inboard joint boot clamp

(2) Remove the protective tape.

(3) Align the matchmarks and install the tripod joint to the front drive outboard joint shaft assembly.

NOTICE:

Face the serrated side of the tripod joint outward and install it to the outboard joint end.

(4) Using a brass bar and a hammer, install the tripod joint to the front drive outboard joint shaft assembly.

NOTICE:

  • Do not tap the rollers.
  • Keep the tripod joint free of foreign matter.
  • Be sure to install the tripod joint in the correct direction.

(5) Using a snap ring expander, install a new shaft snap ring to the front drive outboard joint shaft assembly.

(6) Pack the front drive inboard joint assembly and front axle inboard joint boot with grease.

Standard Grease Capacity:

168 to 178 g (5.93 to 6.28 oz.)

(7) Install a new front axle inboard joint grommet to the front drive inboard joint assembly.

NOTICE:

  • Securely fit the protrusion on the front axle inboard joint grommet into the front drive inboard joint assembly.
  • Make sure that the lip of the front axle inboard joint grommet is not damaged.

(8) Align the matchmarks and install the front drive inboard joint assembly to the front drive outboard joint shaft assembly.

7. INSTALL FRONT AXLE INBOARD JOINT BOOT

(1) Install the front axle inboard joint boot to the front drive inboard joint assembly.

NOTICE:

  • Keep the grooves free of grease.
  • Keep the inside of the front axle inboard joint boot free of foreign matter.

8. INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP

CAUTION:

  • When installing the front axle inboard joint boot clamp, do not perform the procedure without wearing protective gloves.
  • Performing the procedure without wearing protective gloves could result in injury.

*a

Place the tip near the center of the lever

*b

Buckle

(1) Install the front axle inboard joint boot clamp to the front axle inboard joint boot and temporarily fold back the lever.

NOTICE:

  • Make sure that the front axle inboard joint boot clamp is correctly positioned within the groove.
  • Confirm that the front axle inboard joint boot clamp and lever are not deformed or damaged.

(2) Using water pump pliers, temporarily secure the front axle inboard joint boot clamp by pinching the front axle inboard joint boot clamp until a click sound is heard.

NOTICE:

Do not damage the front axle inboard joint boot.

(3) Using a plastic hammer, tap the buckle to secure it while adjusting the clearance between the lever and the groove to make the clearance between the buckle edge and the lever end even.

NOTICE:

  • Do not use excessive force when tapping with the plastic hammer.
  • Do not damage the front axle inboard joint boot.

9. INSTALL FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP

CAUTION:

  • When installing the front No. 2 axle inboard joint boot clamp, do not perform the work without wearing protective gloves.
  • Performing the procedure without wearing protective gloves could result in injury.

*a

Indented Portion

*b

Support Point

(1) Check whether the dimension (A) of each drive shaft is within specification.

Dimension (A) (M20A-FXS):

for LH Side

587.2 to 595.2 mm (1.93 to 1.95 ft.)

for RH Side

891.2 to 899.2 mm (2.92 to 2.95 ft.)

Dimension (A) (2ZR-FXE):

for LH Side

592.2 to 600.2 mm (1.94 to 1.97 ft.)

for RH Side

891.2 to 899.2 mm (2.92 to 2.95 ft.)

(2) While holding dimension (A) to the specified length, pull the indented portion of the inboard joint grommet outward with your finger, etc. to release air from inside the inboard joint and equalize the air pressure with the atmospheric pressure.

(3) Set the folding support point of the clamp so that it is aligned with any of the B portions indicated by arrows in the illustration.

*a

Fulcrum Point

*b

Lever Push Position

*c

Band Support Position

-

-

(1) Temporarily fold back the lever at the fulcrum point.

NOTICE:

  • Check the band and the lever for any deformation before folding back the lever.
  • The lever folds easily at the fulcrum point when pushed at the position shown in the illustration.
  • When folding back the lever, do not push at the end of the lever.

    *a

    Temporary Claw

    -

    -

  • If the lever bends in the middle, it may not engage with the temporary claws or may not be held in the correct position.

*a

Press down

*b

Contact Point

*c

Turn

*d

Temporary Claw

*e

Fulcrum Point

-

-

(1) As shown in the illustration, while pressing the outboard joint area against the work surface, firmly press the lever into place by rolling the outboard joint area forward from the folded fulcrum point to the temporary claw area until a click sound is heard.

NOTICE:

  • Do not damage the deflector.
  • Make sure that the outboard joint is in direct contact with the work surface.

*a

Buckle

-

-

(1) Using a plastic hammer, tap the buckle to secure it while adjusting the clearance between the lever and the groove to make the clearance between the buckle edge and the lever end even.

NOTICE:

  • Do not use excessive force when tapping with the plastic hammer.
  • Do not damage the front axle outboard joint boot.

10. INSPECT FRONT DRIVE SHAFT ASSEMBLY

Click here

Installation

INSTALLATION

HINT:

  • Use the same procedure for the RH side and LH side.
  • The following procedure is for the LH side.
COMPONENTS (INSTALLATION)

Procedure

Part Name Code

1

FRONT DRIVE SHAFT HOLE SNAP RING

43420G

-

-

2

FRONT DRIVE SHAFT ASSEMBLY

43420

-

-

*1

FRONT DRIVE SHAFT OIL SEAL

-

-

●

Non-reusable part

MP grease

Toyota Genuine e-Transaxle Fluid TE

Toyota Genuine Oil Seal Side Lip Grease

Procedure

Part Name Code

3

FRONT DRIVE SHAFT ASSEMBLY

43420

-

-

4

FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY

48069

-

-

-

5

FRONT STABILIZER LINK ASSEMBLY

48810

-

-

6

TIE ROD END SUB-ASSEMBLY

45047

-

-

7

FRONT SPEED SENSOR

89543

-

-

8

FRONT AXLE SHAFT NUT

43502H

-

-

*1

FRONT FLEXIBLE HOSE

*2

FRONT AXLE ASSEMBLY

*3

COTTER PIN

-

-

Tightening torque for "Major areas involving basic Toyota Prius vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf)

●

Non-reusable part

Toyota Body Grease W

Do not apply lubricants to the threaded parts

Procedure

Part Name Code

9

ADD HYBRID TRANSAXLE FLUID

-

-

-

10

INSPECT HYBRID TRANSAXLE FLUID

-

-

-

11

INSPECT FOR HYBRID TRANSAXLE FLUID LEAK

-

-

-

12

FRONT WHEELS

-

-

-

-

13

INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

-

-

-

14

REAR ENGINE UNDER COVER LH

51444A

-

-

-

15

REAR ENGINE UNDER COVER RH

51443C

-

-

-

16

NO. 1 ENGINE UNDER COVER ASSEMBLY

51410

-

-

-

17

CHECK FOR SPEED SENSOR SIGNAL

-

-

-

N*m (kgf*cm, ft.*lbf): Specified torque

-

-

PROCEDURE

1. INSTALL FRONT DRIVE SHAFT HOLE SNAP RING

(1) Install a new front drive shaft hole snap ring.

NOTICE:

Face the end gap of the front drive shaft hole snap ring downward.

2. INSTALL FRONT DRIVE SHAFT ASSEMBLY

MP grease

Toyota Genuine e-Transaxle Fluid TE

Toyota Genuine Oil Seal Side Lip Grease

-

-

(1) Coat the snap ring of the front drive inboard joint assembly with MP grease.

(2) Coat the splines of the front drive inboard joint assembly with Toyota Genuine e-Transaxle Fluid TE.

(3) Coat the lip of the front drive shaft oil seal LH with MP grease and Toyota genuine oil seal side lip grease as shown in the illustration.

HINT:

Apply a light coat of MP grease and Toyota genuine oil seal side lip grease to the entire circumference of the front drive shaft oil seal LH.

(4) Align the inboard joint splines, and using a brass bar and a hammer, install the front drive shaft assembly LH.

NOTICE:

  • Face the end gap of the front drive shaft hole snap ring downward.
  • Do not damage the front drive shaft oil seal.
  • Do not damage the front axle inboard joint boot.
  • Make sure to center the front drive shaft assembly during installation to prevent damage to the front drive shaft hole snap ring.

HINT:

Confirm whether the drive shaft is securely driven in by checking the reaction force and sound.

3. CONNECT FRONT DRIVE SHAFT ASSEMBLY

*a

Matchmark

-

-

Toyota Body Grease W

-

-

(1) Apply 0.1 to 0.3 g (0.00353 to 0.0105 oz.) of Toyota Body Grease W to each of the 4 areas shown in the illustration.

(2) Align the matchmarks and install the front drive shaft assembly to the front axle assembly.

NOTICE:

  • Do not push the front axle assembly towards the outside of the Toyota Prius vehicle any further than necessary.
  • Check that there is no foreign matter on the deflector or contact surfaces.
  • Do not damage the front axle outboard joint boot.
  • Do not damage the front disc brake dust cover.
  • Do not damage the deflector.

4. CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY

Click here

5. INSTALL FRONT STABILIZER LINK ASSEMBLY

Click here

6. CONNECT TIE ROD END SUB-ASSEMBLY

Click here

7. INSTALL FRONT SPEED SENSOR

Click here

8. INSTALL FRONT AXLE SHAFT NUT

(1) Clean the threaded parts on the front drive shaft assembly and a new front axle shaft nut using non-residue solvent.

NOTICE:

  • Be sure to perform this work even when using a new front drive shaft assembly.
  • Keep the threaded parts free of oil and foreign matter.

(2) Using a 30 mm deep socket wrench, install the front axle shaft nut.

HINT:

Keep depressing the brake pedal to prevent the drive shaft from rotating.

Torque:

216 N·m {2203 kgf·cm, 159 ft·lbf}

(3) Using a chisel and a hammer, stake the front axle shaft nut.

9. ADD HYBRID TRANSAXLE FLUID

Click here

10. INSPECT HYBRID TRANSAXLE FLUID

Click here

11. INSPECT FOR HYBRID TRANSAXLE FLUID LEAK

Click here

12. INSTALL FRONT WHEELS

Click here

13. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

Click here

14. INSTALL REAR ENGINE UNDER COVER LH

15. INSTALL REAR ENGINE UNDER COVER RH

16. INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY

for M20A-FXS: Click here

for 2ZR-FXE: Click here

17. CHECK FOR SPEED SENSOR SIGNAL

Click here

18. PERFORM INITIALIZATION

Parking Assist Monitor System

Panoramic View Monitor System

Advanced Park