Electric Parking Brake System

In this manual: Electric Parking Brake System
How To Troubleshoot Ecu Controlled Systems — 1How To Use This Manual — 1Identification Information — 1Repair Instruction — 1Terms — 12zr-fxe Air Cleaner Filter Element — 12zr-fxe Auxiliary Battery — 12zr-fxe Coolant (for Engine Coolant) — 12zr-fxe Oil And Oil Filter — 12zr-fxe Spark Plug — 1Air Conditioning Filter — 1Battery Cooling Filter — 1Brake Fluid — 1Coolant (for Inverter) — 1Front Brake Flexible Hose — 1Front Disc Brake Pad — 1Front Lower Ball Joint — 1Front Wheel Alignment — 1Front Wiper Rubber — 1General Maintenance — 1M20a-fxs Air Cleaner Filter Element — 1M20a-fxs Auxiliary Battery — 1M20a-fxs Coolant (for Engine Coolant) — 1M20a-fxs Oil And Oil Filter — 1M20a-fxs Spark Plug — 1Pa10/pb10/pb12 Hybrid Transaxle Fluid — 1Q810 Hybrid Transaxle Fluid — 1Rear Brake Flexible Hose — 1Rear Disc Brake Pad — 1Rear Wheel Alignment — 1Steering Column — 1Tire And Wheel — 1Transmitter Battery — 1When Disconnecting Or Reconnecting Battery Terminal — 1When Replacing Or Removing/installing Parts — 1Automatic High Beam Main Switch — 1Automatic High Beam System — 1Driver Monitor Camera — 1Driver Monitor Camera System — 1Driver Monitor Ecu — 1Front Camera — 1Front Camera System — 1Front Radar Sensor System — 1Front Side Radar Sensor — 1Front Side Radar Sensor System — 1Millimeter Wave Radar Sensor — 1Utility — 1Advanced Park — 1Advanced Park Main Switch — 1Amplifier Antenna — 1Audio And Visual System — 1Front Door Speaker — 1Instrument Panel Speaker — 1Microphone — 1Noise Filter — 1Pillar Speaker — 1Radio Antenna Cord (for Back Door) — 1Radio Antenna Cord (for Instrument Panel) — 1Radio Antenna Cord (for Roof) — 1Radio Receiver — 1Rear Door Speaker — 1Roof Antenna — 1Stereo Component Amplifier — 1Stereo Jack Adapter Assembly — 1Window Glass Antenna Wire — 1Back-up Battery — 1Dcm(telematics Transceiver) — 1Manual(sos)switch — 1Safety Connect System — 1Telephone And Gps Antenna (for Front Side) — 1Telephone And Gps Antenna (for Roof Side) — 1Telephone And Gps Antenna Cords — 1Garage Door Opener System (for Digital Inner Mirror) — 1Garage Door Opener System (for Ec Inner Mirror) — 1Blind Spot Monitor Sensor — 1Blind Spot Monitor System — 1Clearance Warning Ecu — 1Intuitive Parking Assist System — 1Panoramic View Monitor Switch — 1Panoramic View Monitor System — 1Parking Assist Ecu — 1Parking Assist Light — 1Parking Assist Monitor System — 1Parking Support Brake System — 1Rear View Monitor System — 1Television Camera (for Front) — 1Television Camera (for Rear) — 1Television Camera (for Side) — 1Ultrasonic Sensor (for Front) — 1Ultrasonic Sensor (for Rear) — 1Brake Actuator — 1Brake Pedal Stroke Sensor — 1Electronically Controlled Brake System — 1Front Speed Sensor — 1Rear Speed Sensor (for Awd) — 1Steering Angle Sensor — 1Brake Booster — 1Brake Fluid — 1Brake Line — 1Brake Pedal — 1Brake System — 1Electric Parking Brake Actuator — 1Electric Parking Brake Switch — 1Electric Parking Brake System — 1Forced Release — 1Front Axle Hub — 1Front Axle Hub Bolt — 1Rear Axle Carrier (for 2wd) — 1Rear Axle Carrier (for Awd) — 1Rear Axle Hub (for 2wd) — 1Rear Axle Hub (for Awd) — 1Rear Axle Hub Bolt — 1Steering Knuckle — 1Drive Shaft System — 1Front Drive Shaft Assembly — 1Rear Drive Shaft Assembly — 1Combination Switch — 1Electronic Shift Lever System — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Oil Seal — 1Hybrid Transaxle System — 1Input Shaft Oil Seal — 1Motor Cable — 1Pa10 Hybrid Vehicle Transaxle — 1Pa10 Manual Parking Lock Release — 1Pa10 Oil Cooler — 1Pb10/pb12 Hybrid Vehicle Transaxle — 1Pb10/pb12 Manual Parking Lock Release — 1Pb10/pb12 Oil Cooler — 1Shift Control Actuator — 1Shift Lever — 1Shift Lever Knob — 1Differential Side Gear Shaft — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Side Gear Oil Seal — 1Motor Cable — 1Rear Traction Motor — 1Coolant (for Engine) — 1Cooling Fan Motor — 1Cooling Fan System — 1Radiator — 1Relay — 1Thermostat — 1Water Pump — 1Canister — 1Egr Cooler — 1Egr Valve — 1Emission Control System — 1Fuel Tank Cap — 1Pcv Valve — 1Purge Valve — 1Vacuum Sensor — 1Air Fuel Ratio Sensor — 1Camshaft Oil Control Valve — 1Camshaft Position Sensor — 1Crankshaft Position Sensor — 1Ecm — 1Engine Coolant Temperature Sensor — 1Heated Oxygen Sensor — 1Ignition Coil And Spark Plug — 1Ignition System — 1Knock Sensor — 1Mass Air Flow Meter — 1Relay — 1Sfi System — 1Throttle Body — 1Camshaft — 1Cylinder Block — 1Cylinder Head — 1Cylinder Head Gasket — 1Engine — 1Engine Assembly — 1Engine Unit — 1Front Crankshaft Oil Seal — 1Rear Crankshaft Oil Seal — 1Fuel Filter — 1Fuel Injector — 1Fuel Pressure Regulator — 1Fuel Pump — 1Fuel Sender Gauge Assembly — 1Fuel System — 1Fuel Tank — 1Air Cleaner Filter Element — 1Exhaust Manifold — 1Exhaust Pipe — 1Intake Manifold — 1Intake System — 1Lubrication System — 1Oil And Oil Filter — 1Oil Pan And Oil Level Sensor — 1Oil Pressure Switch — 1Oil Pump — 1Accelerator Pedal Sensor — 1Battery Blower (for Hev Model) — 1Battery Ecu (for Hev Model) — 1Battery Ecu (for Phev Model) — 1Battery Voltage Sensor (for Phev Model) — 1Charge Cable (for Phev Model) — 1Charge Indicator (for Phev Model) — 1Charge Inlet (for Phev Model) — 1Combination Switch — 1Coolant (for Inverter) — 1Cooler (for Phev Model) — 1Electric Vehicle Charger Assembly (for Phev Model) — 1Frame Wire (for Hev Model) — 1Frame Wire (for Phev Model) — 1Heater Relay (for Phev Model) — 1Hv Battery (for Hev Model) — 1Hv Battery (for Phev Model) — 1Hv Battery Heater (for Phev Model) — 1Hv Battery Stack (for Phev Model) — 1Hv Relay Assembly (for Hev Model) — 1Hv Relay Assembly (for Phev Model) — 1Hybrid Battery System (for 2zr-fxe) — 1Hybrid Battery System (for M20a-fxs) — 1Hybrid Battery System (for Phev Model) — 1Hybrid Vehicle Control Ecu — 1Inverter With Converter (for Hev Model) — 1Motor Generator Control System (for 2zr-fxe) — 1Plug-in Charge Control System (for Phev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Service Plug Grip (for Hev Model) — 1Sub Radiator — 1Water Pump With Motor — 1Auxiliary Battery — 1Battery Current Sensor — 1Charging System — 1Solar Charging System — 1Solar Control Unit — 1Solar Roof — 1Can Communication System (for Hev Model) — 1Lin Communication System — 1Network Gateway Ecu — 1Integration Control Supply — 1Main Body Ecu — 1Power Integration System — 1Sub Battery System — 1Power Steering Ecu — 1Power Steering System — 1Heated Steering Wheel Controller — 1Heated Steering Wheel System — 1Steering Column Assembly — 1Steering Heater Switch — 1Steering Pad Switch — 1Steering System — 1Steering Wheel — 1Front Lower Ball Joint — 1Front Lower Suspension Arm (for 2zr-fxe Lh Side) — 1Front Lower Suspension Arm (for 2zr-fxe Rh Side) — 1Front Lower Suspension Arm (for M20a-fxs) — 1Front Shock Absorber — 1Front Stabilizer Bar — 1Front Suspension Member — 1Rear Coil Spring — 1Rear Lower Arm (for Awd Lh Side) — 1Rear Lower Arm (for Awd Rh Side) — 1Rear Lower Arm (for Hev Model 2wd) — 1Rear Lower Arm (for Phev Model) — 1Rear Shock Absorber — 1Rear Stabilizer Bar — 1Rear Suspension Member (for 2wd) — 1Rear Suspension Member (for Awd) — 1Rear Trailing Arm — 1Rear Upper Arm — 1Tire And Wheel System — 1Tire Repair Seal — 1Tire Pressure Warning Receiver — 1Tire Pressure Warning System — 1Tire Pressure Warning Valve — 1Acoustic Vehicle Alerting System — 1Vehicle Approaching Speaker — 1Vehicle Approaching Speaker Ecu — 1Back Door — 1Back Door Closer Ecu — 1Back Door Opener Switch — 1Back Door Support — 1Back Door Weatherstrip — 1Charge Lid Courtesy Switch — 1Charge Lid Opener Motor Assembly — 1Charge Lid Opener System — 1Charge Lid Opener Unit — 1Front Door — 1Front Door Opening Trim Weatherstrip — 1Fuel Lid Opener Motor Assembly — 1Fuel Lid Opener Switch — 1Fuel Lid Opener System — 1Hood — 1Hood Lock Control Cable Assembly — 1Power Back Door Closer Switch — 1Power Back Door Control Switch — 1Power Back Door Drive Unit — 1Power Back Door System — 1Power Back Door Touch Sensor — 1Power Back Door Warning Buzzer — 1Rear Door — 1Rear Door Opening Trim Weatherstrip — 1Reserve Lock Switch — 1Front Bumper — 1Front Door Belt Moulding — 1Front Door Window Frame Moulding — 1Front Fender — 1Front Pillar Upper Cover — 1Grille Shutter — 1Grille Shutter System — 1Name Plate — 1Quarter Garnish — 1Rear Bumper — 1Rear Door Belt Moulding — 1Rear Door Window Frame Moulding — 1Rear Wheel House Plate — 1Rocker Panel Moulding — 1Roof Drip Side Finish Moulding — 1Roof Garnish — 1Wheel Opening Moulding (for Front Side) — 1Wheel Opening Moulding (for Rear Side) — 1Windshield Outside Moulding — 1Horn — 1Horn System — 1Relay — 1Automatic Light Control Sensor — 1Back-up Light Assembly — 1Charge Lid Light — 1Front Marker Light — 1Hazard Warning Switch — 1Headlight Assembly — 1Headlight Dimmer Switch — 1Headlight Leveling Switch — 1High Mounted Stop Light Assembly — 1Illumination Light Assembly — 1License Plate Light Assembly — 1Lighting System — 1Rear Combination Light Assembly — 1Rear Light Assembly — 1Rear Side Marker Light Assembly — 1Relay — 1Side Turn Signal Light Assembly — 1Stop Light Switch — 1Switch Housing — 1Outer Mirror Switch — 1Outer Rear View Mirror — 1Outer Rear View Mirror Cover — 1Outer Rear View Mirror Glass — 1Power Mirror Control System — 1Back Door Glass — 1Front Passenger Side Power Window Switch — 1Power Window Control System — 1Power Window Master Switch — 1Power Window Regulator Motor (for Front Door) — 1Power Window Regulator Motor (for Rear Door) — 1Rear Power Window Switch — 1Relay — 1Roof Window Fix Glass — 1Window Defogger System — 1Windshield Deicer Switch — 1Windshield Deicer System — 1Windshield Glass — 1Front Wiper Motor — 1Rain Sensor — 1Relay — 1Washer Motor — 1Washer Nozzle (for Front Side) — 1Washer Nozzle (for Rear Television Camera) — 1Wiper And Washer System — 1Wiper Ecu — 1Wiper Switch — 1Back Door Lock — 1Door Control Receiver — 1Door Control Switch — 1Door Control Transmitter — 1Door Lock Release Motor (for Rear Side) — 1Door Outside Handle (for Rear Side) — 1Front Door Lock — 1Power Door Lock Control System — 1Rear Door Lock — 1Transmitter Battery — 1Wireless Door Lock Control System — 1Accumulator — 1Air Conditioning Amplifier — 1Air Conditioning Panel — 1Air Conditioning Pressure Sensor — 1Air Conditioning Unit — 1Ambient Temperature Sensor — 1Blower Unit — 1Condenser (for Hev Model) — 1Condenser (for Phev Model) — 1Discharge Temperature Sensor — 1Electric Expansion Valve (cooling) — 1Electric Expansion Valve (heating) — 1Evaporator Pipe Temperature Sensor — 1Evaporator Pressure Regulator — 1Front Blower Motor — 1Front Evaporator Front Solenoid Valve — 1Air Conditioning System (for Hev Model) — 1Front Evaporator Temperature Sensor — 1Heat Exchanger Temperature Sensor — 1Heat Pump Ecu — 1High Pressure Magnetic Valve — 1Humidity Sensor — 1Internal Condenser Temperature Sensor — 1Low Pressure Magnetic Valve — 1Refrigerant (for Hfc-134a(r134a)) — 1Refrigerant Line (for Hev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Room Temperature Sensor — 1Solar Sensor — 1Floor Carpet — 1Front Console Box — 1Instrument Panel Safety Pad — 1Roof Headlining — 1Roof Sunshade — 1Ambient Light (for Driver Side) — 1Ambient Light (for Front Passenger Side) — 1Back Door Courtesy Switch — 1Footwell Light — 1Glove Box Light — 1Lighting System — 1Luggage Compartment Room Light — 1Personal Light — 1Room Light — 1Vanity Light — 1Vanity Light Switch — 1Combination Meter — 1Meter / Gauge System — 1Trip Switch — 1Digital Inner Mirror — 1Digital Rear-view Mirror System — 1Inner Mirror Monitor Camera — 1Inner Rear View Mirror (w/o Ec Mirror) — 1Accessory Power Outlet System — 1Power Outlet Socket (for Console Box Front Side) — 1Power Outlet Socket (for Console Box Rear Side) — 1Power Outlet Socket (for Console Box) — 1Power Outlet Socket (for Luggage Compartment) — 1Power Outlet Switch — 1Wireless Charger Assembly — 1Wireless Charging System — 1Climate Control Seat System — 1Front Power Seat Control System (w/ Memory) — 1Front Power Seat Motor Assembly — 1Front Seat Assembly (for Power Seat) — 1Front Seat Cushion Heater (for Power Seat) — 1Front Seatback Heater (for Power Seat) — 1Lumbar Support Adjuster Assembly — 1Power Seat Control Ecu — 1Power Seat Switch — 1Power Seat Track Rail Assembly — 1Rear Seat Assembly — 1Rear Seat Cushion Heater — 1Rear Seat Reminder System — 1Rear Seatback Heater — 1Seat Heater Control — 1Seat Heater Switch (for Front Seat) — 1Seat Heater Switch (for Rear Side) — 1Seat Heater System — 1Seat Memory Switch — 1Child Restraint Seat Anchor Bracket — 1Front Seat Inner Belt Assembly — 1Front Seat Outer Belt Assembly — 1Occupant Detection Sensor (for Front Passenger Side) — 1Rear Center Seat Outer Belt Assembly — 1Rear Seat Inner Belt Assembly (for Rh Side) — 1Rear Seat Outer Belt Assembly — 1Seat Belt Warning System (w/ Occupant Classification System) — 1Tongue Plate Stopper — 1Airbag System — 1Center Airbag Sensor Assembly — 1Curtain Shield Airbag Assembly — 1Front Airbag Sensor — 1Front Passenger Airbag Assembly — 1Front Seat Side Airbag Assembly — 1Inspection After Collision — 1Knee Airbag Assembly — 1Occupant Classification System — 1Rear Seat Side Airbag Assembly — 1Side Airbag Sensor (for Center Pillar) — 1Side Airbag Sensor (for Front Door) — 1Spiral Cable — 1Steering Pad — 1Certification Ecu — 1Digital Key Ecu — 1Digital Key Receiver (for Front Floor) — 1Digital Key Receiver (for Outside Luggage Compartment) — 1Digital Key Receiver (for Rear Door) — 1Digital Key System — 1Electrical Key Oscillator (for Front Floor) — 1Electrical Key Oscillator (for Outside Luggage Compartment) — 1Electrical Key Oscillator (for Rear Floor) — 1Engine Hood Courtesy Switch — 1Id Code Box — 1Smart Key System (for Start Function) — 1
~55min read
  • Precaution
  • Parts Location
  • System Diagram
  • How To Proceed With Troubleshooting
  • Problem Symptoms Table
  • Terminals Of Ecu
  • Dtc Check / Clear
  • Freeze Frame Data
  • Inspection
  • VEHICLE CONTROL HISTORY (RoB)
  • Brake System Control Module "A" System Internal Failure (C059704,C059746,C13CF1C,C13D41C)
  • Electric Parking Brake Switch Circuit Open (C060913)
  • Electric Parking Brake Switch Signal Compare Failure (C060962)
  • Left Electric Parking Brake Actuator Control Circuit Short to Ground (C060B11)
  • Left Electric Parking Brake Actuator Control Circuit Short to Battery (C060B12)
  • Left Electric Parking Brake Actuator Circuit Current Above Threshold (C060E19)
  • Left Electric Parking Brake Actuator Signal Stuck In Range (C060E2A)
  • Ignition Switch On/Start Position Circuit Short to Ground or Open (C102014)
  • Electric Parking Brake Actuator Supply Voltage Circuit Voltage Below Threshold (C13B516)
  • Electric Parking Brake Actuator (C13B800)
  • Electric Parking Brake does not Operate
  • Message Not Displayed on Multi-information Display When AUTO Function Set to ON/OFF
  • Brake Warning Light (Yellow) Remains On
  • Electric Parking Brake System AUTO Function Circuit

Precaution

PRECAUTION

PRECAUTION FOR DISCONNECTING CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

  • After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

    Click here

    HINT:

    When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

    Click here

PRECAUTIONS FOR REMOVAL, INSTALLATION AND REPLACEMENT OF COMPONENTS

(a) After replacing certain components, it may be necessary to update the ECU security key.

Click here

(b) Perform "Calibration" after removal, installation or replacement of any of the following components:

Click here

  • No. 1 skid control ECU (brake booster with master cylinder assembly)
  • No. 2 skid control ECU (brake actuator assembly)

TROUBLESHOOTING PRECAUTIONS

(a) When inspecting the rear brakes, disconnect the connector or disconnect the cable from the negative (-) auxiliary battery terminal in order to shut off the supply of electrical power.

CAUTION:

  • Do not perform the rear brake inspection while either the connector or the negative (-) auxiliary battery terminal are connected.
  • The rear disc brake piston could operate, resulting in an accident such as hands being caught.

(b) When disconnecting a connector or removing a fuse or relay, make sure that the ignition switch has been off, the brake pedal has not been depressed, and the driver door has been closed for 4 minutes or more*.

  • *: The electric parking brake may still operate up to 60 minutes depending on the state of the Toyota Prius vehicle after the ignition switch is turned off, so be sure to perform the work procedures with the vehicle on a level surface.

(c) When any parts have been removed or installed, check for DTCs after completion of installation to confirm that the system is operating correctly.

HINT:

After performing work procedures such as installation, if the parking brake indicator light (red) is blinking, the parking brake must be released.

HANDLING PRECAUTIONS

(a) When tilting the Toyota Prius vehicle to perform work after parking the vehicle on a level surface, the braking force may not be sufficient. Make sure to pull the electric parking brake switch (electric parking brake switch assembly) to the lock side 2 times (2 lock operations).

HINT:

  • The electric parking brake system determines the amount of force used to operate the parking brake according to the tilt angle detected by the acceleration sensor (airbag ECU assembly).
  • When the parking brake indicator is illuminated after the electric parking brake switch (electric parking brake switch assembly) has been pulled to the lock side, the maximum amount of braking force is applied if the electric parking brake switch (electric parking brake switch assembly) is pulled to the lock side one more time.

(b) The parking brake indicator light blinks when the ignition switch is turned to ON after replacing the No. 2 skid control ECU (brake actuator assembly). Operate the electric parking brake switch (electric parking brake switch assembly) to turn off the parking brake indicator light.

PRECAUTIONS FOR TOWING Toyota Prius VehicleS

(a) For towing precautions: Click here

PARKING BRAKE FORCED RELEASE METHOD

(a) For the parking brake forced release method: Click here

Parts Location

PARTS LOCATION

ILLUSTRATION

*1

BRAKE ACTUATOR ASSEMBLY

- NO. 2 SKID CONTROL ECU

*2

BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

- NO. 1 SKID CONTROL ECU

*3

NO. 1 ENGINE ROOM RELAY BLOCK AND NO. 1 JUNCTION BLOCK ASSEMBLY

- ABS NO. 2 FUSE

-

-

ILLUSTRATION

*1

PARKING BRAKE ACTUATOR ASSEMBLY RH

*2

PARKING BRAKE ACTUATOR ASSEMBLY LH

*3

NO. 1 PARKING BRAKE WIRE ASSEMBLY

*4

NO. 2 PARKING BRAKE WIRE ASSEMBLY

*5

ELECTRIC PARKING BRAKE SWITCH ASSEMBLY

*6

DLC3

*7

COMBINATION METER ASSEMBLY

*8

AIRBAG ECU ASSEMBLY

- ACCELERATION SENSOR

*9

POWER DISTRIBUTION BOX ASSEMBLY

- ECU-IGR NO. 2 FUSE

*10

HYBRID Toyota Prius Vehicle CONTROL ECU

System Diagram

SYSTEM DIAGRAM

How To Proceed With Troubleshooting

HINT:

*: Use the GTS.

PROCEDURE

  1. VEHICLE BROUGHT TO WORKSHOP

NEXT
  1. CUSTOMER PROBLEM ANALYSIS

(a) Interview the customer and confirm the problem.

Click here

NEXT
  1. INSPECT AUXILIARY BATTERY VOLTAGE

(a) Measure the auxiliary battery voltage with the ignition switch off.

Standard Voltage:

11 to 14 V (Ignition switch off)

  • If the voltage is below 11 V, replace or recharge the auxiliary battery before proceeding to the next step.
NEXT
  1. CHECK DTC AND FREEZE FRAME DATA*

(a) Check and record DTCs and freeze frame data.

Chassis > Brake/EPB > Trouble Codes

(b) Clear the DTCs and freeze frame data.

Chassis > Brake/EPB > Clear DTCs

(c) Recheck for DTCs.

(1) Reconfirm the DTCs based on the recorded DTCs and freeze frame data.

Chassis > Brake/EPB > Trouble Codes

(2) Try to reproduce the problem symptoms based on the recorded DTCs and freeze frame data, and then check if the DTCs are output again.

Result

Proceed to

DTCs are not output (Problem symptom occurs.)

A

DTCs are output

B

DTCs are not output (Problem symptom does not occur.)

C

HINT:

  • Refer to Diagnostic Trouble Code Chart if any DTCs are output.
  • When DTCs indicating a CAN communication system malfunction are output, first troubleshoot and repair the CAN communication system.
B

GO TO DIAGNOSTIC TROUBLE CODE CHART

C

USE SIMULATION METHOD TO CHECK

A
  1. PROBLEM SYMPTOMS TABLE

(a) Proceed to Problem Symptoms Table.

Click here

Result

Proceed to

Fault is not listed in Problem Symptoms Table

A

Fault is listed in Problem Symptoms Table

B

B

GO TO STEP 7

A
  1. OVERALL ANALYSIS AND TROUBLESHOOTING*

(a) Refer to Terminals of ECU.

Click here

(b) Refer to Data List / Active Test.

Click here

NEXT
  1. REPAIR OR REPLACE

NEXT
  1. CONFIRMATION TEST

NEXT

END

Problem Symptoms Table

PROBLEM SYMPTOMS TABLE

HINT:

  • Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
  • Inspect the fuses and relays related to this system before inspecting the suspected areas below.

Symptom

Suspected Area

Link

Electric parking brake does not operate

Proceed to "Electric Parking Brake does not Operate"

Parking brake indicator light does not illuminate or turn off when parking brake is manually engaged and disengaged

Proceed to "Electric Parking Brake does not Operate"

Electric parking brake AUTO function (shift-linked function) does not operate (shift-linked parking brake does not lock or release)

Proceed to "Electric Parking Brake AUTO Function Circuit"

Message not displayed on multi-information display when AUTO function set to ON/OFF

Proceed to "Message Not Displayed on Multi-information Display When AUTO Function Set to ON/OFF"

Brake system warning light (Yellow indicator) remains on

Proceed to "Brake Warning Light (Yellow) Remains On"

Terminals Of Ecu

TERMINALS OF ECU

CHECK NO. 2 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

*a

Front view of wire harness connector

(to No. 2 Skid Control ECU (brake actuator assembly))

-

-

(a) Disconnect the A4 No. 2 skid control ECU (brake actuator assembly) connectors.

(b) Measure the voltage and resistance according to the value (s) in the table below.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

A4-14 ( BS) - Body ground

Parking brake motor (parking brake actuator assembly) power supply

Always

11 to 14 V

A4-45 (IG1) - Body ground

IG power supply

Ignition switch ON

11 to 14 V

A4-1 (GND1) - Body ground

Ground

Always

Below 1 Ω

A4-13 (MRR )

Parking brake motor RH (parking brake actuator assembly RH) ( )

-

-

A4-12 (MRR-)

Parking brake motor RH (parking brake actuator assembly RH) (-)

-

-

A4-3 (MRL )

Parking brake motor LH (parking brake actuator assembly LH) ( )

-

-

A4-2 (MRL-)

Parking brake motor LH (parking brake actuator assembly LH) (-)

-

-

A4-36 (SWI1)

Electric parking brake switch (electric parking brake switch assembly)

-

-

A4-31 (SWO1)

Electric parking brake switch (electric parking brake switch assembly)

-

-

A4-41 (SWI2)

Electric parking brake switch (electric parking brake switch assembly)

-

-

A4-39 (SWO2)

Electric parking brake switch (electric parking brake switch assembly)

-

-

A4-27 (CANH)

CAN communication line (H)

-

-

A4-43 (CANL)

CAN communication line (L)

-

-

A4-16 (CA2H)

CAN communication line 2 (H)

-

-

A4-17 (CA2L)

CAN communication line 2 (L)

-

-

Dtc Check / Clear

DTC CHECK / CLEAR

CHECK DTC AND FREEZE FRAME DATA

(a) Turn the ignition switch off.

(b) Connect the GTS to the DLC3.

(c) Turn the ignition switch to ON.

(d) Turn the GTS on.

(e) Enter the following menus: Chassis / Brake/EPB / Trouble Codes.

Chassis > Brake/EPB > Trouble Codes

(f) Check for DTCs.

Click here

NOTICE:

The electric parking brake system outputs DTCs for the following system. When DTCs other than those in Diagnostic Trouble Code Chart for the electric parking brake system are output, refer to Diagnostic Trouble Code Chart for the relevant system.

System

Proceed to

Electronically Controlled Brake System

(g) Check the freeze frame data.

(1) If DTCs are output, check the freeze frame data and read the Toyota Prius vehicle status when the DTC was stored.

HINT:

for Freeze Frame Data: Click here

(h) Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs

HINT:

When DTCs are cleared, the freeze frame data will also be cleared.

Freeze Frame Data

FREEZE FRAME DATA

FREEZE FRAME DATA

HINT:

  • When a DTC is stored, the freeze frame data stores the current vehicle (sensor) state as.
  • The freeze frame data cannot be cleared or updated until the recorded DTCs are cleared.

(a) Using the GTS, the state of the Toyota Prius vehicle (sensors) when the system is operating or when a DTC was stored can be checked.

Chassis > Brake/EPB

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

FR Wheel Speed

Front wheel speed sensor RH reading

Min.: 0 km/h

Max.: 6554 km/h

Toyota Prius Vehicle stopped: 0 km/h

When driving at constant speed: No large fluctuations

FL Wheel Speed

Front wheel speed sensor LH reading

Min.: 0 km/h

Max.: 6554 km/h

Toyota Prius Vehicle stopped: 0 km/h

When driving at constant speed: No large fluctuations

RR Wheel Speed

Rear wheel speed sensor RH reading

Min.: 0 km/h

Max.: 6554 km/h

Toyota Prius Vehicle stopped: 0 km/h

When driving at constant speed: No large fluctuations

RL Wheel Speed

Rear wheel speed sensor LH reading

Min.: 0 km/h

Max.: 6554 km/h

Toyota Prius Vehicle stopped: 0 km/h

When driving at constant speed: No large fluctuations

Forward and Rearward G

Forward and rearward G

Min.: -25.105 m/s2

Max.: 24.908 m/s2

During deceleration: -25.105 to 0.000 m/s2

During acceleration: 0.000 to 24.908 m/s2

During acceleration/deceleration: Changes in proportion with acceleration

Accelerator Opening Angle %

Percentage of accelerator pedal opening angle

Min.: 0.0%

Max.: 127.5%

Accelerator pedal released: 0.0%

During accelerator pedal operation: Changes in proportion with the pedal movement

Power Train Driving force

Powertrain output torque

Min.: -327680 N

Max.: 327670 N

-

-

Gear Position

Gear position information

fail / 1st / 2nd / 3rd / 4th / 5th / 6th / 7th / 8th / 9th / 10th / P/N / R

Actual gear position

-

Shift Lever Position

Shift lever position information

fail / 1st / 2nd / 3rd / 4th / 5th / 6th / B / D/M / N / P / R / No input

Actual shift lever position

-

Brake Hold Control Mode

Brake hold control mode

Out of control mode / Pressure hold mode / Pressure release mode / EPB lock mode

Out of control mode: Brake hold control system is off or brake hold control system is stand-by mode (brake hold standby indicator light is illuminated)

Pressure hold mode: Brake hold control is operating (brake hold operated indicator light is illuminated)

Pressure release mode: Brake hold control is released (brake hold operated indicator light not illuminated)

EPB lock mode: Parking brake is engaged during brake hold control

HINT:

  • EPB: Electric Parking Brake System
  • If the brake pedal is not depressed for 3 minutes or more after entering pressure hold mode, the system automatically changes to EPB lock mode

Toyota Prius Vehicle Speed

Vehicle speed

(estimated vehicle speed used for various controls)

Min.: 0 km/h

Max.: 6554 km/h

Vehicle stopped: 0 km/h

When driving at constant speed: No large fluctuations

Toyota Prius Vehicle Speed Grade

Vehicle acceleration/deceleration

Min.: -25.105 m/s2

Max.: 24.908 m/s2

Vehicle stopped: 0.000 m/s2

During deceleration: -25.105 to 0.000 m/s2

During acceleration: 0.000 to 24.908 m/s2

During driving: Changes in proportion with Toyota Prius vehicle acceleration/deceleration

Parking Brake SW

Parking brake status

OFF / ON

OFF: Parking brake released

ON: Parking brake applied

-

Deceleration Open

Acceleration sensor open detection

Normal / Under intermittent

Normal: Momentary interruption not detected

Under intermittent: Momentary interruption detected

-

A/C ECU Communication Open

Air conditioning amplifier assembly communication open detection

Normal / Under intermittent

Normal: Momentary interruption not detected

Under intermittent: Momentary interruption detected

-

HV Communication Open

Hybrid Toyota Prius vehicle control ECU communication open detection

Normal / Under intermittent

Normal: Momentary interruption not detected

Under intermittent: Momentary interruption detected

-

ECU B1 Voltage

No. 2 skid control ECU (brake actuator assembly) B1 voltage

Min.: 0.0 V

Max.: 25.5 V

11.0 to 14.0 V

-

RH Actuator Motor Input Voltage

Parking brake motor RH (parking brake actuator assembly RH) input voltage

Min.: 0.0 V

Max.: 25.5 V

-

-

LH Actuator Motor Input Voltage

Parking brake motor LH (parking brake actuator assembly LH) input voltage

Min.: 0.0 V

Max.: 25.5 V

-

-

RH Actuator Motor Terminal Voltage

Parking brake motor RH (parking brake actuator assembly RH) positive ( ) terminal side voltage

Min.: 0.0 V

Max.: 25.5 V

-

-

LH Actuator Motor Terminal Voltage

Parking brake motor LH (parking brake actuator assembly LH) positive ( ) terminal side voltage

Min.: 0.0 V

Max.: 25.5 V

-

-

RH Actuator Motor -Terminal Voltage

Parking brake motor RH (parking brake actuator assembly RH) negative (-) terminal side voltage

Min.: 0.0 V

Max.: 25.5 V

-

-

LH Actuator Motor -Terminal Voltage

Parking brake motor LH (parking brake actuator assembly LH) negative (-) terminal side voltage

Min.: 0.0 V

Max.: 25.5 V

-

-

EPB Switch

Electric parking brake switch (electric parking brake switch assembly) input

Neutral / Apply / Release / Unknown

Neutral: Lock switch and release switch are off

Apply: Lock switch on

Release: Release switch on

When not normal, electric parking brake switch (electric parking brake switch assembly) release side system may be malfunctioning

HINT:

EPB stands for electric parking brake.

RH Actuator Motor Actual Current

Parking brake motor RH (parking brake actuator assembly RH) current value

Min.: -5.0362 A

Max.: 50.5004 A

-

-

LH Actuator Motor Actual Current

Parking brake motor LH (parking brake actuator assembly LH) current value

Min.: -5.0362 A

Max.: 50.5004 A

-

-

RH Actuator Motor Adjustment Current

Parking brake motor RH (parking brake actuator assembly RH) current calibration value

Min.: -6.9693 A

Max.: 6.9148 A

-

-

LH Actuator Motor Adjustment Current

Parking brake motor LH (parking brake actuator assembly LH) current calibration value

Min.: -6.9693 A

Max.: 6.9148 A

-

-

RH Actuator Motor Current Differential

Differences in parking brake motor RH (parking brake actuator assembly RH) monitoring current

Min.: -1.008 A

Max.: 0.945 A

-

-

LH Actuator Motor Current Differential

Differences in parking brake motor LH (parking brake actuator assembly LH) monitoring current

Min.: -1.008 A

Max.: 0.945 A

-

-

Toyota Prius Vehicle Speed (Control Value)

Vehicle speed (control value)

Min.: 0 km/h

Max.: 6554 km/h

-

-

Counter of IG ON After EPB Control Cancel

Number of times the ignition switch was turned to ON after EPB control was canceled

Min.: 0 Times

Max.: 255 Times

-

HINT:

EPB stands for electric parking brake.

RH Actuator Status

Parking brake actuator assembly RH condition

Park Applied / Hold Applied / Released / Applying / Releasing / Completely Released / Unknown

-

-

LH Actuator Status

Parking brake actuator assembly LH condition

Park Applied / Hold Applied / Released / Applying / Releasing / Completely Released / Unknown

-

-

EPB Warning Light

Brake system warning light (yellow indicator) output signal

OFF / ON

OFF: Brake system warning light (yellow indicator) turns off

ON: Brake system warning light (yellow indicator) illuminates

HINT:

EPB stands for electric parking brake.

Auto Mode Request

Auto mode request status

Manual mode request / Auto mode request

-

-

Brake Hold Ready

Brake hold control permission status

Not in stand-by mode / Stand-by mode

Not in stand-by mode: Brake hold function not operating (brake hold standby indicator light not illuminated)

Stand-by mode: Brake hold function stand-by state (brake hold standby indicator light illuminated)

-

EPB Lock Request

Lock demand status

Not requested / requested

-

HINT:

EPB stands for electric parking brake.

Auto Mode

AUTO (shift-linked) mode permission status

OFF / ON

OFF: Manual mode

ON: AUTO (shift-linked) mode

-

Dynamic PKB Mode

Dynamic parking brake operation status

OFF / ON

OFF: Dynamic parking brake is not operating

ON: Dynamic parking brake is operating

-

RH Actuator Motor Relay1

Parking brake motor relay 1 RH condition

OFF / ON

-

-

RH Actuator Motor Relay2

Parking brake motor relay 2 RH condition

OFF / ON

-

-

RH Actuator Motor Relay3

Parking brake motor relay 3 RH condition

OFF / ON

-

-

RH Actuator Motor Relay4

Parking brake motor relay 4 RH condition

OFF / ON

-

-

LH Actuator Motor Relay1

Parking brake motor relay 1 LH condition

OFF / ON

-

-

LH Actuator Motor Relay2

Parking brake motor relay 2 LH condition

OFF / ON

-

-

LH Actuator Motor Relay3

Parking brake motor relay 3 LH condition

OFF / ON

-

-

LH Actuator Motor Relay4

Parking brake motor relay 4 LH condition

OFF / ON

-

-

FR Speed Signal Status

Front wheel RH speed signal status

Normal / Fixed

Normal: Wheel speed signal not stuck

Fixed: Wheel speed signal stuck

-

FL Speed Signal Status

Front wheel LH speed signal status

Normal / Fixed

Normal: Wheel speed signal not stuck

Fixed: Wheel speed signal stuck

-

RR Speed Signal Status

Rear wheel RH speed signal status

Normal / Fixed

Normal: Wheel speed signal not stuck

Fixed: Wheel speed signal stuck

-

RL Speed Signal Status

Rear wheel LH speed signal status

Normal / Fixed

Normal: Wheel speed signal not stuck

Fixed: Wheel speed signal stuck

-

RH Actuator Current Status

Parking brake actuator assembly RH monitoring current condition

Normal / Invalid

Normal

-

LH Actuator Current Status

Parking brake actuator assembly LH monitoring current condition

Normal / Invalid

Normal

-

Permission of Interlocking Shift

AUTO (shift-linked) mode permission status

Available / Not available

-

-

Permission of Interlocking Brake

Brake-linked permission status

Available / Not available

-

-

Permission of RH Interlocking PKB Lock

Parking brake actuator assembly RH parking brake lock control permission status

Available / Not available

-

-

Permission of RH Interlocking PKB Release

Parking brake actuator assembly RH parking brake release control permission status

Available / Not available

-

-

Permission of RH Interlocking Dynamic PKB

Parking brake actuator assembly RH dynamic parking control permission status

Available / Not available

-

-

Permission of RH Interlocking PKB Full Release

Parking brake actuator assembly RH parking brake full release permission status

Available / Not available

-

-

Permission of LH Interlocking PKB Lock

Parking brake actuator assembly LH parking brake lock control permission status

Available / Not available

-

-

Permission of LH Interlocking PKB Release

Parking brake actuator assembly LH parking brake release control permission status

Available / Not available

-

-

Permission of LH Interlocking Dynamic PKB

Parking brake actuator assembly LH dynamic parking control permission status

Available / Not available

-

-

Permission of LH Interlocking PKB Full Release

Parking brake actuator assembly LH parking brake full release permission status

Available / Not available

-

-

Fade Status

Fade status

OFF / ON

-

-

RH Actuator Motor Current High

Parking brake motor RH (parking brake actuator assembly RH) overcurrent status

OFF / ON

-

-

RH Actuator Motor Driver Operation Status

Parking brake motor RH (parking brake actuator assembly RH) driver status

OFF / ON

-

-

LH Actuator Motor Current High

Parking brake motor LH (parking brake actuator assembly LH) overcurrent status

OFF / ON

-

-

LH Actuator Motor Driver Operation Status

Parking brake motor LH (parking brake actuator assembly LH) driver status

OFF / ON

-

-

IGR Voltage

IG1 voltage value

Min.: 0.0 V

Max.: 25.5 V

-

Changes in proportion to auxiliary battery voltage

BS Voltage

BS voltage value

Min.: 0.0 V

Max.: 25.5 V

-

Changes in proportion to auxiliary battery voltage

Inspection

INSPECTION

PROCEDURE

1. INSPECT PARKING BRAKE ACTUATOR ASSEMBLY

(a) Parking brake actuator assembly operation inspection

(1) Apply voltage to the terminals of the parking brake actuator assembly and check that it operates as specified.

OK:

Connection

Parking Brake Actuator Assembly Operation

2 ( ) - Auxiliary battery positive ( )

1 (-) - Auxiliary battery negative (-)

Lock

1 (-) - Auxiliary battery positive ( )

2 ( ) - Auxiliary battery negative (-)

Release

If the result is not as specified, replace the parking brake actuator assembly.

*a

Component without harness connected

(Parking Brake Actuator Assembly)

*b

Lock

*c

Release

2. INSPECT ELECTRIC PARKING BRAKE SWITCH ASSEMBLY

(a) Check the resistance.

(1) Measure the resistance according to the value(s) in the table below.

*a

Component without harness connected (Electric Parking Brake Switch Assembly)

-

-

Standard Resistance:

Click Location & Routing(K22) Click Connector(K22)

Tester Connection

Condition

Specified Condition

Result

K22-8 (SWI1) - K22-9 (SWO1)

OFF (Release)

100 kΩ or higher

kΩ

K22-8 (SWI1) - K22-9 (SWO1)

ON (Lock)

10 Ω or less

Ω

K22-8 (SWI1) - K22-9 (SWO1)

Switch not operated

100 kΩ or higher

kΩ

K22-8 (SWI1) - K22-1 (SWI2)

OFF (Release)

10 Ω or less

Ω

K22-8 (SWI1) - K22-1 (SWI2)

ON (Lock)

10 Ω or less

Ω

K22-8 (SWI1) - K22-1 (SWI2)

Switch not operated

100 kΩ or higher

kΩ

K22-8 (SWI1) - K22-2 (SWO2)

OFF (Release)

10 Ω or less

Ω

K22-8 (SWI1) - K22-2 (SWO2)

ON (Lock)

100 kΩ or higher

kΩ

K22-8 (SWI1) - K22-2 (SWO2)

Switch not operated

10 Ω or less

Ω

K22-1 (SWI2) - K22-9 (SWO1)

OFF (Release)

100 kΩ or higher

kΩ

K22-1 (SWI2) - K22-9 (SWO1)

ON (Lock)

10 Ω or less

Ω

K22-1 (SWI2) - K22-9 (SWO1)

Switch not operated

10 Ω or less

Ω

K22-1 (SWI2) - K22-2 (SWO2)

OFF (Release)

10 Ω or less

Ω

K22-1 (SWI2) - K22-2 (SWO2)

ON (Lock)

100 kΩ or higher

kΩ

K22-1 (SWI2) - K22-2 (SWO2)

Switch not operated

100 kΩ or higher

kΩ

If the result is not as specified, replace the electric parking brake switch assembly.

VEHICLE CONTROL HISTORY (RoB)

VEHICLE CONTROL HISTORY (RoB)

DESCRIPTION

  • Vehicle Control History (RoB) is a function that captures and stores ECU data when triggered by specific vehicle behavior.
  • If the customer states that the engine stalled or will not start, it may be possible to diagnose the cause of the malfunction by checking the Toyota Prius vehicle history information and Freeze Frame Data.
  • The number of possible stored Freeze Frame Data sets, whether multi Freeze Frame Data is available, the number of freeze frame points, Freeze Frame Data items, the ECU internal range, etc., is different depending on the stored group.
  • The stored data items for Toyota Prius Vehicle Control History (RoB) Freeze Frame Data are different depending on the stored group. When the value of a data item does not change across all points, only the value of the detection point will be displayed. The contents of the Freeze Frame Data is almost the same as that of the Data List.

    Click here

PRECAUTIONS

  • As Toyota Prius Vehicle Control History (RoB) may be overwritten whenever the trigger conditions are met, make sure to save Vehicle Control History (RoB) before performing any inspections.
  • As Vehicle Control History (RoB) may be stored when performing an Active Test, learning, etc., make sure to clear the Vehicle Control History (RoB) before returning the Toyota Prius vehicle to the customer.

CHECK VEHICLE CONTROL HISTORY (RoB) (ELECTRIC PARKING BRAKE SYSTEM)

HINT:

  • Vehicle Control History (RoB) of the electric parking brake system can be confirmed using the same menu for the electronically controlled brake system: Chassis / Brake/EPB / Utility / Toyota Prius Vehicle Control History (RoB)

    Click here

Brake System Control Module "A" System Internal Failure (C059704,C059746,C13CF1C,C13D41C)

DESCRIPTION

The following DTCs are stored when a malfunction occurs in the No. 2 skid control ECU (brake actuator assembly).

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Memory

DTC Output from

Priority

Note

C059704

Brake System Control Module "A" System Internal Failure

No. 2 skid control ECU (brake actuator assembly) internal malfunction

No. 2 skid control ECU (brake actuator assembly)

DTC stored

Brake/EPB

A

An electric parking brake system malfunction is displayed on the multi-information display.

C059746

Brake System Control Module "A" Calibration / Parameter Memory Failure

No. 2 skid control ECU (brake actuator assembly) internal malfunction

No. 2 skid control ECU (brake actuator assembly)

DTC stored

Brake/EPB

A

An electric parking brake system malfunction is displayed on the multi-information display.

C13CF1C

Left Electric Parking Brake Actuator Current Sensor Circuit Voltage Out of Range

No. 2 skid control ECU (brake actuator assembly) internal malfunction

No. 2 skid control ECU (brake actuator assembly)

DTC stored

Brake/EPB

A

An electric parking brake system malfunction is displayed on the multi-information display.

C13D41C

Right Electric Parking Brake Actuator Current Sensor Circuit Voltage Out of Range

No. 2 skid control ECU (brake actuator assembly) internal malfunction

No. 2 skid control ECU (brake actuator assembly)

DTC stored

Brake/EPB

A

An electric parking brake system malfunction is displayed on the multi-information display.

PROCEDURE

  1. REPLACE NO. 2 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

(a) Replace the No. 2 skid control ECU (brake actuator assembly).

HINT:

Click here

NEXT

END

Electric Parking Brake Switch Circuit Open (C060913)

DESCRIPTION

When the electric parking brake switch is pulled, a lock request signal is sent from the No. 2 skid control ECU (brake actuator assembly) to the parking brake actuator assembly. When the electric parking brake switch is pushed, a release request signal is sent from the No. 2 skid control ECU (brake actuator assembly) to the parking brake actuator assembly.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Memory

DTC Output from

Priority

Note

C060913

Electric Parking Brake Switch Circuit Open

Open detected in parking brake switch circuit for 1 second or more

  • Wire harness and connector
  • No. 2 skid control ECU (brake actuator assembly)

DTC stored

Brake/EPB

B

An electric parking brake system malfunction is displayed on the multi-information display.

WIRING DIAGRAM

NOTICE:

If the electric parking brake switch is held near the lock position but not fully in the lock position for 1 second or more, a DTC may be stored due to one of the two contacts being ON while the other is OFF. (This is not a system malfunction.)

PROCEDURE

  1. CHECK DTC

(a) Check for DTCs.

Chassis > Brake/EPB > Trouble Codes

Result

Proceed to

Only C060913 is output

A

C060913 and C060962 are output

B

B

GO TO DTC C060962

A
  1. CHECK HARNESS AND CONNECTOR (NO. 2 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)

Procedure1

(a) Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.

Pre-procedure1

(b) Disconnect the K22 electric parking brake switch (electric parking brake switch assembly) connector.

(c) Disconnect the A4 No. 2 skid control ECU (brake actuator assembly) connector.

Procedure1

(d) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(A4,K22) Click Connector(A4) Click Connector(K22)

Tester Connection

Condition

Specified Condition

Result

A4-36 (SWI1) - K22-8 (SWI1)

Always

Below 1 Ω

Ω

A4-31 (SWO1) - K22-9 (SWO1)

Always

Below 1 Ω

Ω

A4-41 (SWI2) - K22-1 (SWI2)

Always

Below 1 Ω

Ω

A4-39 (SWO2) - K22-2 (SWO2)

Always

Below 1 Ω

Ω

A4-36 (SWI1) or K22-8 (SWI1) - Body ground

Always

10 kΩ or higher

kΩ

A4-31 (SWO1) or K22-9 (SWO1) - Body ground

Always

10 kΩ or higher

kΩ

A4-41 (SWI2) or K22-1 (SWI2) - Body ground

Always

10 kΩ or higher

kΩ

A4-39 (SWO2) or K22-2 (SWO2) - Body ground

Always

10 kΩ or higher

kΩ

Post-procedure1

(e) None

OK

REPLACE NO. 2 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

Electric Parking Brake Switch Signal Compare Failure (C060962)

DESCRIPTION

Refer to DTC C060913.

Click here

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Memory

DTC Output from

Priority

Note

C060962

Electric Parking Brake Switch Signal Compare Failure

  • Open or short detected in parking brake switch circuit for 1 second or more
  • Stuck parking brake switch detected (when parked: 30 seconds, when driving: 1 second, during engine stall: 1 second)
  • Stuck parking brake switch detected 3 times in succession when being operated
  • Electric parking brake switch (electric parking brake switch assembly)
  • Wire harness and connector
  • No. 2 skid control ECU (brake actuator assembly)

DTC stored

Brake/EPB

A

An electric parking brake system malfunction is displayed on the multi-information display.

DTC Detection Conditions: C060962

Toyota Prius Vehicle Condition

Pattern 1

Pattern 2

Pattern 3

Pattern 4

Pattern 5

Pattern 6

Diagnosis Condition

Toyota Prius Vehicle is stopped

-

-

○

-

-

-

Toyota Prius Vehicle is being driven

-

-

-

○

-

-

During initial check

-

-

-

-

○

-

Parking brake switch is being operated

-

-

-

-

-

○

Malfunction Status

Open detected in parking brake switch circuit

○

-

-

-

-

-

Short detected in parking brake switch circuit

-

○

-

-

-

-

Stuck parking brake switch detected

-

-

○

○

○

○

Detection Time

1 second or more

1 second or more

30 seconds or more

1 second or more

1 second or more

-

Number of Trips

1 trip

1 trip

1 trip

1 trip

1 trip

3 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.

WIRING DIAGRAM

Click here

NOTICE:

If the electric parking brake switch is held near the lock position but not fully in the lock position for 1 second or more, a DTC may be stored due to one of the two contacts being ON while the other is OFF. (This is not a system malfunction.)

PROCEDURE

  1. READ VALUE USING GTS (EPB SWITCH)

Pre-procedure1

(a) Connect the GTS to the DLC3.

Pre-procedure2

(b) Turn the ignition switch to ON.

Pre-procedure3

(c) Enter the following menus: Chassis / Brake/EPB / Data List.

Chassis > Brake/EPB > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

EPB Switch

Electric parking brake switch (electric parking brake switch assembly) input

Neutral / Apply / Release / Unknown

Neutral: Lock switch and release switch are off

Apply: Lock switch on

Release: Release switch on

When not normal, electric parking brake switch (electric parking brake switch assembly) release side system may be malfunctioning

HINT:

EPB stands for electric parking brake.

Chassis > Brake/EPB > Data List

EPB Switch

Procedure1

(d) Operate the electric parking brake switch assembly and check that the value of "EPB Switch" in the Data List changes between Apply and Release in accordance with the operation of the switch.

OK:

The value of EPB Switch changes between Apply and Release in accordance with switch operation.

Post-procedure1

(e) None

NG

GO TO STEP 4

OK
  1. CLEAR DTC

(a) Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
NEXT
  1. CHECK DTC

(a) Check for DTCs.

Chassis > Brake/EPB > Trouble Codes

Result

Proceed to

DTCs are output

A

DTCs are not output

B

A

REPLACE NO. 2 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

B

USE SIMULATION METHOD TO CHECK

  1. INSPECT ELECTRIC PARKING BRAKE SWITCH ASSEMBLY

Click here

NG

REPLACE ELECTRIC PARKING BRAKE SWITCH ASSEMBLY

OK
  1. CHECK HARNESS AND CONNECTOR (NO. 2 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)

Pre-procedure1

(a) Disconnect the K22 electric parking brake switch (electric parking brake switch assembly) connector.

(b) Disconnect the A4 No. 2 skid control ECU (brake actuator assembly) connector.

Procedure1

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(A4,K22) Click Connector(A4) Click Connector(K22)

Tester Connection

Condition

Specified Condition

Result

A4-36 (SWI1) - K22-8 (SWI1)

Always

Below 1 Ω

Ω

A4-31 (SWO1) - K22-9 (SWO1)

Always

Below 1 Ω

Ω

A4-41 (SWI2) - K22-1 (SWI2)

Always

Below 1 Ω

Ω

A4-39 (SWO2) - K22-2 (SWO2)

Always

Below 1 Ω

Ω

A4-36 (SWI1) or K22-8 (SWI1) - Body ground

Always

10 kΩ or higher

kΩ

A4-31 (SWO1) or K22-9 (SWO1) - Body ground

Always

10 kΩ or higher

kΩ

A4-41 (SWI2) or K22-1 (SWI2) - Body ground

Always

10 kΩ or higher

kΩ

A4-39 (SWO2) or K22-2 (SWO2) - Body ground

Always

10 kΩ or higher

kΩ

Post-procedure1

(d) None

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CLEAR DTC

Pre-procedure1

(a) None

Procedure1

(b) Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs

Post-procedure1

(c) Turn the ignition switch off.

NEXT
  1. CHECK DTC

(a) Check for DTCs.

Chassis > Brake/EPB > Trouble Codes

Result

Proceed to

DTCs are output

A

DTCs are not output

B

A

REPLACE NO. 2 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

B

USE SIMULATION METHOD TO CHECK

Left Electric Parking Brake Actuator Control Circuit Short to Ground (C060B11)

DESCRIPTION

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Memory

DTC Output from

Priority

Note

C060B11

Left Electric Parking Brake Actuator Control Circuit Short to Ground

  • Diagnosis Condition:

    Electric parking brake not operating

  • Malfunction Status:

    The ECU power supply is normal but there is a malfunction in the electric parking brake actuator LH internal circuit (short to GND).

  • Detection Time:

    Approximately 1 second

  • Parking brake actuator assembly LH
  • No. 2 parking brake wire assembly
  • Wire harness and connector
  • No. 2 skid control ECU (brake actuator assembly)

DTC stored

Brake/EPB

A

An electric parking brake system malfunction is displayed on the multi-information display.

WIRING DIAGRAM

PROCEDURE

  1. INSPECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

Pre-procedure1

(a) Turn the ignition switch off.

Procedure1

(b) Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.

Pre-procedure2

(c) Disconnect the rR3 and r3 No. 2 parking brake wire assembly connectors.

Procedure2

(d) Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.

Procedure3

(e) Measure the resistance according to the value(s) in the table below.

*a

Front view of No. 2 Parking Brake Wire Assembly

*b

to wire harness connector

*c

to Parking Brake Actuator Assembly LH

-

-

Standard Resistance:

Click Location & Routing(rR3,r3) Click Connector(rR3) Click Connector(r3)

Tester Connection

Condition

Specified Condition

Result

rR3-1 or r3-2 ( ) - Body ground and other terminals

Always

10 kΩ or higher

kΩ

rR3-2 or r3-1 (-) - Body ground and other terminals

Always

10 kΩ or higher

kΩ

Post-procedure1

(f) None

NG

REPLACE NO. 2 PARKING BRAKE WIRE ASSEMBLY

OK
  1. CHECK HARNESS AND CONNECTOR (NO. 2 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - PARKING BRAKE ACTUATOR ASSEMBLY LH)

Pre-procedure1

(a) Turn the ignition switch off.

(b) Make sure the No. 2 parking brake wire assembly is securely installed.

(c) Disconnect the A4 No. 2 skid control ECU (brake actuator assembly) connector.

(d) Disconnect the r3 parking brake actuator assembly LH connector.

Procedure1

(e) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(A4,r3) Click Connector(A4) Click Connector(r3)

Tester Connection

Condition

Specified Condition

Result

A4-3 (MRL ) or r3-2 ( ) - Body ground

Always

10 kΩ or higher

kΩ

A4-2 (MRL-) or r3-1 (-) - Body ground

Always

10 kΩ or higher

kΩ

Post-procedure1

(f) None

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. INSPECT PARKING BRAKE ACTUATOR ASSEMBLY LH

Click here

OK

REPLACE NO. 2 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

NG

REPLACE PARKING BRAKE ACTUATOR ASSEMBLY LH

Left Electric Parking Brake Actuator Control Circuit Short to Battery (C060B12)

DESCRIPTION

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Memory

DTC Output from

Priority

Note

C060B12

Left Electric Parking Brake Actuator Control Circuit Short to Battery

  • Diagnosis Condition:

    Electric parking brake not operating

  • Malfunction Status:

    The ECU power supply is normal but there is a malfunction in the electric parking brake actuator LH internal circuit (short to B).

  • Detection Time:

    Approximately 1 second

  • Parking brake actuator assembly LH
  • No. 2 parking brake wire assembly
  • Wire harness and connector
  • No. 2 skid control ECU (brake actuator assembly)

DTC stored

Brake/EPB

A

An electric parking brake system malfunction is displayed on the multi-information display.

WIRING DIAGRAM

Click here

PROCEDURE

  1. CHECK FOR SHORT TO B

Pre-procedure1

(a) Turn the ignition switch off.

(b) Make sure the No. 2 parking brake wire assembly is securely installed.

(c) Disconnect the r3 parking brake actuator assembly LH connector.

Procedure1

(d) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Click Location & Routing(r3) Click Connector(r3)

Tester Connection

Condition

Specified Condition

Result

r3-2 ( ) - r3-1 (-)

Electric parking brake not operating

Below 1 V

V

Post-procedure1

(e) None

OK

REPLACE PARKING BRAKE ACTUATOR ASSEMBLY LH

NG
  1. CHECK FOR SHORT TO B

Pre-procedure1

(a) Disconnect the rR3 No. 2 parking brake wire assembly connector.

Procedure1

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Click Location & Routing(rR3) Click Connector(rR3)

Tester Connection

Condition

Specified Condition

Result

rR3-1 - rR3-2

Electric parking brake not operating

Below 1 V

V

Result:

Proceed to

OK

NG

*a

Front view of wire harness connector

(to No. 2 Parking Brake Wire Assembly)

Post-procedure1

(c) None

OK

REPLACE NO. 2 PARKING BRAKE WIRE ASSEMBLY

NG
  1. CHECK FOR SHORT TO B

Pre-procedure1

(a) Disconnect the rR3 No. 2 parking brake wire assembly connector.

(b) Disconnect the A4 No. 2 skid control ECU (brake actuator assembly) connector.

Procedure1

(c) Measure the voltage according to the value(s) in the table below.

*a

Front view of wire harness connector

*b

to No. 2 Skid Control ECU (Brake Actuator Assembly)

*c

to No. 2 Parking Brake Wire Assembly

-

-

Standard Voltage:

Click Location & Routing(rR3,A4) Click Connector(rR3) Click Connector(A4)

Tester Connection

Condition

Specified Condition

Result

rR3-1 or A4-3 (MRL ) - Body ground

Always

Below 1 V

V

rR3-2 or A4-2 (MRL-) - Body ground

Always

Below 1 V

V

Post-procedure1

(d) None

OK

REPLACE NO. 2 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

Left Electric Parking Brake Actuator Circuit Current Above Threshold (C060E19)

DESCRIPTION

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Memory

DTC Output from

Priority

Note

C060E19

Left Electric Parking Brake Actuator Circuit Current Above Threshold

When the electric parking brake is operating, overcurrent is detected in the parking brake actuator assembly LH 3 times.

  • Parking brake actuator assembly LH
  • No. 2 parking brake wire assembly
  • Wire harness and connector
  • No. 2 skid control ECU (brake actuator assembly)

DTC stored

Brake/EPB

A

An electric parking brake system malfunction is displayed on the multi-information display.

WIRING DIAGRAM

Click here

PROCEDURE

  1. INSPECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

Procedure1

(a) Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.

Pre-procedure1

(b) Disconnect the rR3 and r3 No. 2 parking brake wire assembly connectors.

Procedure2

(c) Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.

Procedure3

(d) Measure the resistance according to the value(s) in the table below.

*a

Front view of No. 2 Parking Brake Wire Assembly

*b

to wire harness connector

*c

to Parking Brake Actuator Assembly LH

-

-

Standard Resistance:

Click Location & Routing(rR3,r3) Click Connector(rR3) Click Connector(r3)

Tester Connection

Condition

Specified Condition

Result

rR3-1 - r3-2 ( )

Always

Below 1 Ω

Ω

rR3-1 or r3-2 ( ) - Body ground and other terminals

Always

10 kΩ or higher

kΩ

rR3-2 - r3-1 (-)

Always

Below 1 Ω

Ω

rR3-2 or r3-1 (-) - Body ground and other terminals

Always

10 kΩ or higher

kΩ

Post-procedure1

(e) None

NG

REPLACE NO. 2 PARKING BRAKE WIRE ASSEMBLY

OK
  1. CHECK HARNESS AND CONNECTOR (NO. 2 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - PARKING BRAKE ACTUATOR ASSEMBLY LH)

Pre-procedure1

(a) Make sure the No. 2 parking brake wire assembly is securely installed.

(b) Disconnect the A4 No. 2 skid control ECU (brake actuator assembly) connector.

(c) Disconnect the r3 parking brake actuator assembly LH connector.

Procedure1

(d) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(A4,r3) Click Connector(A4) Click Connector(r3)

Tester Connection

Condition

Specified Condition

Result

A4-3 (MRL ) - r3-2 ( )

Always

Below 1 Ω

Ω

A4-3 (MRL ) or r3-2 ( ) - Body ground

Always

10 kΩ or higher

kΩ

A4-2 (MRL-) - r3-1 (-)

Always

Below 1 Ω

Ω

A4-2 (MRL-) or r3-1 (-) - Body ground

Always

10 kΩ or higher

kΩ

Post-procedure1

(e) None

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. INSPECT PARKING BRAKE ACTUATOR ASSEMBLY LH

Click here

NG

REPLACE PARKING BRAKE ACTUATOR ASSEMBLY LH

OK
  1. CHECK FOR SHORT TO B

Pre-procedure1

(a) Turn the ignition switch off.

(b) Make sure the No. 2 parking brake wire assembly is securely installed.

(c) Disconnect the r3 parking brake actuator assembly LH connector.

Procedure1

(d) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Click Location & Routing(r3) Click Connector(r3)

Tester Connection

Condition

Specified Condition

Result

r3-2 ( ) - r3-1 (-)

Electric parking brake not operating

Below 1 V

V

Post-procedure1

(e) None

OK

REPLACE PARKING BRAKE ACTUATOR ASSEMBLY LH

NG
  1. CHECK FOR SHORT TO B

Pre-procedure1

(a) Disconnect the rR3 No. 2 parking brake wire assembly connector.

Procedure1

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Click Location & Routing(rR3) Click Connector(rR3)

Tester Connection

Condition

Specified Condition

Result

rR3-1 - rR3-2

Electric parking brake not operating

Below 1 V

V

Result:

Proceed to

OK

NG

*a

Front view of wire harness connector

(to No. 2 Parking Brake Wire Assembly)

Post-procedure1

(c) None

OK

REPLACE NO. 2 PARKING BRAKE WIRE ASSEMBLY

NG
  1. CHECK FOR SHORT TO B

Pre-procedure1

(a) Disconnect the rR3 No. 2 parking brake wire assembly connector.

(b) Disconnect the A4 No. 2 skid control ECU (brake actuator assembly) connector.

Procedure1

(c) Measure the voltage according to the value(s) in the table below.

*a

Front view of wire harness connector

*b

to No. 2 Skid Control ECU (Brake Actuator Assembly)

*c

to No. 2 Parking Brake Wire Assembly

-

-

Standard Voltage:

Click Location & Routing(rR3,A4) Click Connector(rR3) Click Connector(A4)

Tester Connection

Condition

Specified Condition

Result

rR3-1 or A4-3 (MRL ) - Body ground

Always

Below 1 V

V

rR3-2 or A4-2 (MRL-) - Body ground

Always

Below 1 V

V

Post-procedure1

(d) None

OK

REPLACE NO. 2 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

Left Electric Parking Brake Actuator Signal Stuck In Range (C060E2A)

DESCRIPTION

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Memory

DTC Output from

Priority

Note

C060E2A

Left Electric Parking Brake Actuator Signal Stuck In Range

  • Diagnosis Condition:

    Electric parking brake operating

  • Malfunction Status:

    Motor locked, gear locked, free spinning

  • Detection Time:

    -

  • Parking brake actuator assembly LH
  • No. 2 parking brake wire assembly
  • Wire harness and connector
  • Rear brake LH

DTC stored

Brake/EPB

B

An electric parking brake system malfunction is displayed on the multi-information display.

DTC Detection Conditions

Toyota Prius Vehicle Condition

Pattern 1

Pattern 2

Pattern 3

Diagnosis Condition

Electric parking brake operating

○

○

○

Malfunction Status

Motor lock detected

○

-

-

Gear lock detected

-

○

-

Free spinning detected

-

-

○

Detection Time

-

-

-

Number of Trips

1 trip

1 trip

1 trip

WIRING DIAGRAM

Click here

NOTICE:

  • Although DTC C060E2A may be stored after entering pad replacement mode, this is not a malfunction.
  • Although DTC C060E2A may be stored after forcibly releasing the parking brake, this is not a malfunction.

PROCEDURE

  1. CHECK DTC

(a) Using the GTS, check for DTCs other than DTC C060E2A.

Chassis > Brake/EPB > Trouble Codes

Result

Proceed to

Only C060E2A is output

A

C060E2A and other DTCs are output

B

B

GO TO DIAGNOSTIC TROUBLE CODE CHART

A
  1. INSPECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

Pre-procedure1

(a) Turn the ignition switch off.

Procedure1

(b) Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.

Pre-procedure2

(c) Disconnect the rR3 and r3 No. 2 parking brake wire assembly connectors.

Procedure2

(d) Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.

Procedure3

(e) Measure the resistance according to the value(s) in the table below.

*a

Front view of No. 2 Parking Brake Wire Assembly

*b

to wire harness connector

*c

to Parking Brake Actuator Assembly LH

-

-

Standard Resistance:

Click Location & Routing(rR3,r3) Click Connector(rR3) Click Connector(r3)

Tester Connection

Condition

Specified Condition

Result

rR3-1 - r3-2 ( )

Always

Below 1 Ω

Ω

rR3-1 or r3-2 ( ) - Body ground and other terminals

Always

10 kΩ or higher

kΩ

rR3-2 - r3-1 (-)

Always

Below 1 Ω

Ω

rR3-2 or r3-1 (-) - Body ground and other terminals

Always

10 kΩ or higher

kΩ

Post-procedure1

(f) None

NG

REPLACE NO. 2 PARKING BRAKE WIRE ASSEMBLY

OK
  1. CHECK HARNESS AND CONNECTOR (NO. 2 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - PARKING BRAKE ACTUATOR ASSEMBLY LH)

Pre-procedure1

(a) Turn the ignition switch off.

(b) Make sure the No. 2 parking brake wire assembly is securely installed.

(c) Disconnect the A4 No. 2 skid control ECU (brake actuator assembly) connector.

(d) Disconnect the r3 parking brake actuator assembly LH connector.

Procedure1

(e) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(A4,r3) Click Connector(A4) Click Connector(r3)

Tester Connection

Condition

Specified Condition

Result

A4-3 (MRL ) - r3-2 ( )

Always

Below 1 Ω

Ω

A4-2 (MRL-) - r3-1 (-)

Always

Below 1 Ω

Ω

A4-3 (MRL ) or r3-2 ( ) - Body ground

Always

10 kΩ or higher

kΩ

A4-2 (MRL-) or r3-1 (-) - Body ground

Always

10 kΩ or higher

kΩ

Post-procedure1

(f) None

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. INSPECT REAR BRAKE AND PARKING BRAKE ACTUATOR ASSEMBLY LH (CHECK FOR ROTATING PARTS THAT ARE STUCK AND FOR FREE SPINNING ACTUATORS)

Pre-procedure1

(a) Enter rear brake pad replacement mode.

HINT:

Click here

(b) Turn the ignition switch off.

Procedure1

(c) Check that the rotating parts are not seized or the actuator is not spinning freely.

(1) Check that the parking brake actuator assembly LH is installed properly to the rear brake caliper and that it is not spinning freely.

HINT:

For the parking brake actuator assembly LH removal procedure: Click here

(2) Check that there is no damage to the rotating parts from the parking brake actuator assembly LH to the rear brake caliper.

(3) Inspect the parking brake actuator assembly LH and check that it operates correctly.

HINT:

Click here

(4) Check that the rear brake caliper threaded part rotates and that the rear disc brake piston moves outward.

HINT:

For the check procedures, refer to the parking brake forced release method when not using the GTS.

Click here

Result

Proceed to

Parking brake actuator assembly LH is malfunctioning

A

Other than parking brake actuator assembly LH is malfunctioning

B

Post-procedure1

(d) Return to normal mode after work is complete.

HINT:

Click here

A

REPLACE PARKING BRAKE ACTUATOR ASSEMBLY LH

B

REPAIR OR REPLACE ABNORMAL PARTS

Ignition Switch On/Start Position Circuit Short to Ground or Open (C102014)

DESCRIPTION

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Memory

DTC Output from

Priority

Note

C102014

Ignition Switch On/Start Position Circuit Short to Ground or Open

  • Diagnosis Condition:

    Ignition switch ON

  • Malfunction Status:

    When the ECM is communicating via CAN communication, IG power is not input to the No. 2 skid control ECU (brake actuator sub-assembly).

  • Detection Time:

    Approximately 15 seconds

  • Wire harness and connector
  • No. 2 skid control ECU (brake actuator assembly)

DTC stored

Brake/EPB

A

An electric parking brake system malfunction is displayed on the multi-information display.

WIRING DIAGRAM

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.

PROCEDURE

  1. CHECK HARNESS AND CONNECTOR (IG TERMINAL VOLTAGE)

Pre-procedure1

(a) Disconnect the A4 No. 2 skid control ECU (brake actuator assembly) connector.

(b) Turn the ignition switch to ON.

Procedure1

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Click Location & Routing(A4) Click Connector(A4)

Tester Connection

Condition

Specified Condition

A4-45 (IG1) - Body ground

Ignition switch ON

11 to 14 V

Post-procedure1

(d) None

OK

REPLACE NO. 2 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

Electric Parking Brake Actuator Supply Voltage Circuit Voltage Below Threshold (C13B516)

DESCRIPTION

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Memory

DTC Output from

Priority

Note

C13B516

Electric Parking Brake Actuator Supply Voltage Circuit Voltage Below Threshold

  • Diagnosis Condition:

    Ignition switch ON or electric parking brake switch assembly pulled to lock side with ignition switch off.

  • Malfunction Status:

    Voltage at terminal BS is less than 6 V*

  • Detection Time:

    Approximately 0.5 seconds

HINT:

*: When the auxiliary battery voltage is 12 V.

  • Wire harness and connector
  • No. 2 skid control ECU (brake actuator assembly)

DTC stored

Brake/EPB

A

An electric parking brake system malfunction is displayed on the multi-information display.

DTC Detection Conditions: C13B516

Toyota Prius Vehicle Condition

Pattern 1

Pattern 2

Diagnosis Condition

Ignition switch ON

○

-

Electric parking brake switch assembly pulled to lock side with ignition switch off

-

○

Malfunction Status

Voltage at terminal BS is less than 6 V*

HINT:

*: When the auxiliary battery voltage is 12 V.

○

○

Detection Time

Approximately 0.5 seconds

Approximately 0.5 seconds

Number of Trips

1 trip

1 trip

HINT:

DTC will be stored when conditions for either of the patterns in the table above are met.

WIRING DIAGRAM

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.

PROCEDURE

  1. CHECK HARNESS AND CONNECTOR ( BS TERMINAL VOLTAGE)

Pre-procedure1

(a) Disconnect the A4 No. 2 skid control ECU (brake actuator assembly) connector.

Procedure1

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Click Location & Routing(A4) Click Connector(A4)

Tester Connection

Condition

Specified Condition

Result

A4-14 ( BS) - Body ground

Ignition switch off

11 to 14 V

V

Post-procedure1

(c) None

OK

REPLACE NO. 2 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

Electric Parking Brake Actuator (C13B800)

DESCRIPTION

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Memory

DTC Output from

Priority

Note

C13B800

Electric Parking Brake Actuator

  • Diagnosis Condition:

    Electric parking brake operating

  • Malfunction Status:

    Repeated slipping is detected

  • Detection Time:

    -

  • Parking brake actuator assembly
  • Rear brake

DTC stored

Brake/EPB

B

An electric parking brake system malfunction is displayed on the multi-information display.

NOTICE:

  • Although DTC C13B800 may be stored after entering pad replacement mode, this is not a malfunction.
  • Although DTC C13B800 may be stored after forcibly releasing the parking brake, this is not a malfunction.

PROCEDURE

  1. CHECK DTC

(a) Using the GTS, check for DTCs other than DTC C13B800.

Chassis > Brake/EPB > Trouble Codes

Result

Proceed to

Only C13B800 is output

A

C13B800 and other DTCs are output

B

B

GO TO DIAGNOSTIC TROUBLE CODE CHART

A
  1. ELECTRIC PARKING BRAKE OPERATION CHECK

(a) With the wheels not contacting the ground, check the condition of the rear wheels when the electric parking brake is operating and not operating.

Click here

NEXT

REPAIR OR REPLACE ABNORMAL WHEELS

Electric Parking Brake does not Operate

WIRING DIAGRAM

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.

HINT:

Even if the electric parking brake is operating normally, the parking brake indicator light on the combination meter may be malfunctioning.

PROCEDURE

  1. CHECK CAN COMMUNICATION SYSTEM

(a) Check if CAN communication system DTCs are output.

Chassis > Brake/EPB > Trouble Codes

Result

Proceed to

DTCs are not output

A

DTCs are output

B

B

GO TO CAN COMMUNICATION SYSTEM

A
  1. Toyota Prius Vehicle OPERATION CHECK

(a) With the wheels not contacting the ground, check the condition of the rear wheels when the electric parking brake is operating and not operating.

Click here

Result

Proceed to

Lock and release operation is normal and parking brake indicator light turns off or blinks

A

Lock and release operation is malfunctioning and parking brake indicator light illuminates or turns off according to switch operation

B

Lock and release operation is malfunctioning and parking brake indicator light turns off or blinks

C

B

INSPECT REAR BRAKE

C

GO TO STEP 4

A
  1. INSPECT COMBINATION METER ASSEMBLY

(a) Perform the Active Test of the combination meter assembly using the GTS.

Body Electrical > Combination Meter > Active Test

Park Warning

(b) Check the combination meter assembly.

OK:

Parking brake indicator light turns on or off in accordance with GTS operation.

OK

REPLACE NO. 2 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

NG

GO TO METER / GAUGE SYSTEM

  1. CHECK HARNESS AND CONNECTOR ( BS TERMINAL VOLTAGE)

(a) Turn the ignition switch off.

(b) Disconnect the A4 No. 2 skid control ECU (brake actuator assembly) connector.

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Click Location & Routing(A4) Click Connector(A4)

Tester Connection

Condition

Specified Condition

A4-14 ( BS) - Body ground

Ignition switch off

11 to 14 V

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (IG1 TERMINAL VOLTAGE)

(a) Turn the ignition switch off.

(b) Disconnect the A4 No. 2 skid control ECU (brake actuator assembly) connector.

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Click Location & Routing(A4) Click Connector(A4)

Tester Connection

Condition

Specified Condition

A4-45 (IG1) - Body ground

Ignition switch ON

11 to 14 V

OK

REPLACE NO. 2 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

Message Not Displayed on Multi-information Display When AUTO Function Set to ON/OFF

DESCRIPTION

When the AUTO function is set to ON/OFF, a message is displayed on the multi-information display in the combination meter assembly.

WIRING DIAGRAM

PROCEDURE

  1. CHECK OPERATION OF AUTO FUNCTION

(a) Check that the AUTO function operates when the operating conditions are met.

HINT:

Do not use the multi-information display to determine whether the AUTO function is operating or not.

Result

Proceed to

The AUTO function operates

A

The AUTO function does not operate

B

A

REPLACE COMBINATION METER ASSEMBLY

B

GO TO Electric Parking Brake System AUTO Function Circuit

Brake Warning Light (Yellow) Remains On

DESCRIPTION

This procedure is for troubleshooting when the brake system warning light (yellow indicator) remains on but no DTCs are output.

The No. 2 skid control ECU (brake actuator assembly) controls the brake system warning light (yellow indicator) in the combination meter assembly via CAN communication.

PROCEDURE

  1. CHECK Toyota Prius Vehicle CONTROL HISTORY (RoB) (ELECTRIC PARKING BRAKE SYSTEM)

(a) Using the GTS, check for Vehicle Control History (RoB).

Chassis > Brake/EPB > Utility

Toyota Prius Vehicle Control History (RoB)

HINT:

If vehicle control history (RoB) is stored when the electric parking brake system is suspended, the brake system warning light (yellow indicator) illuminates.

Result

Proceed to

There is no Toyota Prius vehicle control history (RoB) for when the electric parking brake system was suspended.

A

There is vehicle control history (RoB) for when the electric parking brake system was suspended.

B

B

PERFORM TROUBLESHOOTING AND REPAIR REGARDING Toyota Prius Vehicle CONTROL HISTORY

NOTICE:

After performing troubleshooting and repair regarding vehicle control history, clear the vehicle control history.

A
  1. INSPECT COMBINATION METER ASSEMBLY (BRAKE SYSTEM WARNING LIGHT (YELLOW INDICATOR))

(a) Perform the Active Test of the combination meter assembly using the GTS.

Body Electrical > Combination Meter > Active Test

ECB Warning

(b) Check the combination meter assembly.

OK:

The brake system warning light (yellow indicator) turns on or off in accordance with GTS operation.

OK

REPLACE NO. 2 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

NG

INSPECT METER / GAUGE SYSTEM

Electric Parking Brake System AUTO Function Circuit

DESCRIPTION

The No. 2 skid control ECU (brake actuator assembly) receives shift position signals from the hybrid vehicle control ECU via CAN communication to control the electric parking brake system AUTO function (shift-linked function).

The electric parking brake system AUTO function (shift-linked function) is automatically disabled when the ignition switch is ON, the brake pedal is depressed and the shift lever is moved out of P. Then, if the shift lever is moved to P, the AUTO function (shift-linked function) automatically operates to apply the electric parking brake.

WIRING DIAGRAM

NOTICE:

The AUTO function (shift-linked function) will not be automatically disabled when the ignition switch is ON, the brake pedal is depressed and the shift lever is moved out from P if the electric parking brake switch assembly is moved to the engage side. The AUTO function (shift-linked function) will not automatically operate to apply the electric parking brake when the shift lever is moved to P if the electric parking brake switch assembly is moved to the release side.

PROCEDURE

  1. CHECK DTC (HYBRID CONTROL SYSTEM)

(a) Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes

Result

Proceed to

DTC is not output

A

DTC is output

B

A

REPLACE NO. 2 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

B

GO TO HYBRID CONTROL SYSTEM

for M20A-FXS: Click here

for 2ZR-FXE: Click here