Steering Angle Sensor
- Removal
- Installation
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during steering angle sensor removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/ReplacedReplaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
Steering sensor |
Update ECU security key |
Toyota Prius Vehicle Control History (RoB) are stored |
NOTICE:
If both the spiral cable sub-assembly and the steering sensor are malfunctioning, replace them with a new spiral cable with sensor sub-assembly.
HINT:
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when Toyota Prius vehicle is drivenEffect/Inoperative Function when Necessary Procedure not Performed | Necessary Procedure | Link |
|---|---|---|
Front Camera System |
Drive the Toyota Prius vehicle straight ahead at 35 km/h or more for 5 seconds or more. |
Effect/Inoperative Function when Necessary Procedure not Performed | Necessary Procedure | Link |
|---|---|---|
| *1: w/o Power Back Door System *2: w/ Power Back Door System |
||
Power Door Lock Control System*1
|
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. |
|
Power Back Door System*2 |
Reset back door close position |
|
Air Conditioning System |
for HEV Model:
|
- |

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY |
- |
- |
- |
- |
2 |
STEERING SENSOR |
89245B |
- |
- |
|
*1 |
SPIRAL CABLE SUB-ASSEMBLY |
- |
- |
PROCEDURE
1. REMOVE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
Click here ![]()
2. REMOVE STEERING SENSOR
![]() |
NOTICE:
|

*a |
Guide |
*b |
Pin |
(1) Disengage the 6 claws, 2 guides and 2 pins, and remove the steering sensor from the spiral cable sub-assembly.
NOTICE:
Do not damage the claws or pins of the spiral cable sub-assembly.
Installation
INSTALLATION
NOTICE:
- After performing the update ECU security key procedure, make sure to perform the initialization procedure for when the cable has been disconnected and reconnected to the negative (-) auxiliary battery terminal.
- A lock pin is installed to a new steering sensor. Do not remove the lock pin before the steering sensor is installed to the spiral cable sub-assembly.

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
INSPECT SPIRAL CABLE SUB-ASSEMBLY |
84306 |
- |
- |
|
2 |
STEERING SENSOR |
89245B |
- |
- |
|
3 |
SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY |
- |
- |
- |
|
4 |
UPPER STEERING COLUMN COVER |
45286B |
- |
- |
- |
5 |
LOWER STEERING COLUMN COVER |
45287 |
- |
- |
- |
6 |
ALIGN FRONT WHEELS FACING STRAIGHT AHEAD |
- |
- |
- |
|
7 |
ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY |
84306 |
- |
- |
|
*1 |
SPIRAL CABLE SUB-ASSEMBLY |
- |
- |

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
8 |
STEERING WHEEL ASSEMBLY |
45100 |
- |
- |
|
9 |
HORN BUTTON ASSEMBLY |
45130 |
- |
- |
|
10 |
NO. 3 STEERING WHEEL COVER LOWER |
45187 |
- |
- |
- |
11 |
NO. 2 STEERING WHEEL COVER LOWER |
45186 |
- |
- |
- |
12 |
CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL |
- |
- |
- |
- |
13 |
UPDATE ECU SECURITY KEY |
- |
- |
- |
|
14 |
INSPECT SRS WARNING LIGHT |
- |
- |
- |
|
15 |
INSPECT HORN BUTTON ASSEMBLY |
45130 |
- |
- |
|
16 |
CHECK STEERING WHEEL CENTER POINT |
- |
- |
- |
|
17 |
INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL |
- |
- |
- |
|
![]() |
Tightening torque for "Major areas involving basic Toyota Prius vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |
- |
- |
PROCEDURE
1. INSPECT SPIRAL CABLE SUB-ASSEMBLY
Click here
![]()
2. INSTALL STEERING SENSOR

*a |
Guide |
*b |
Pin |
*c |
Lock Pin |
- |
- |
(1) Align the 2 pins and 2 guides, and engage the 6 claws to install the steering sensor to the spiral cable sub-assembly.
NOTICE:
- Do not remove the lock pin before the steering sensor is installed to the spiral cable sub-assembly.
- Do not damage the pins of the spiral cable sub-assembly or guides of the steering sensor.
- The spiral cable sub-assembly can be rotated up to 30° even when the interlock is engaged. Therefore, make sure that both guides are aligned properly when installing the steering sensor to the spiral cable sub-assembly.
(2) Remove the lock pin from the steering sensor.
3. INSTALL SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
![]() |
Click here |
4. INSTALL UPPER STEERING COLUMN COVER
Click here
![]()
5. INSTALL LOWER STEERING COLUMN COVER
Click here
![]()
6. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
7. ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
Click here
![]()
8. INSTALL STEERING WHEEL ASSEMBLY
![]() |
Click here |
9. INSTALL HORN BUTTON ASSEMBLY
![]() |
Click here |
10. INSTALL NO. 3 STEERING WHEEL COVER LOWER
Click here ![]()
11. INSTALL NO. 2 STEERING WHEEL COVER LOWER
Click here ![]()
12. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
for M20A-FXS: Click here ![]()
for 2ZR-FXE: Click here ![]()
13. UPDATE ECU SECURITY KEY
Click here ![]()
HINT:
When the steering sensor is replaced with a new one, ECU security key is necessary.
14. INSPECT SRS WARNING LIGHT
Click here ![]()
15. INSPECT HORN BUTTON ASSEMBLY
Click here ![]()
16. CHECK STEERING WHEEL CENTER POINT
Click here ![]()
17. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL
HINT:
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system are used.
Click here
![]()































