Occupant Classification System

In this manual: Occupant Classification System
How To Troubleshoot Ecu Controlled Systems — 1How To Use This Manual — 1Identification Information — 1Repair Instruction — 1Terms — 12zr-fxe Air Cleaner Filter Element — 12zr-fxe Auxiliary Battery — 12zr-fxe Coolant (for Engine Coolant) — 12zr-fxe Oil And Oil Filter — 12zr-fxe Spark Plug — 1Air Conditioning Filter — 1Battery Cooling Filter — 1Brake Fluid — 1Coolant (for Inverter) — 1Front Brake Flexible Hose — 1Front Disc Brake Pad — 1Front Lower Ball Joint — 1Front Wheel Alignment — 1Front Wiper Rubber — 1General Maintenance — 1M20a-fxs Air Cleaner Filter Element — 1M20a-fxs Auxiliary Battery — 1M20a-fxs Coolant (for Engine Coolant) — 1M20a-fxs Oil And Oil Filter — 1M20a-fxs Spark Plug — 1Pa10/pb10/pb12 Hybrid Transaxle Fluid — 1Q810 Hybrid Transaxle Fluid — 1Rear Brake Flexible Hose — 1Rear Disc Brake Pad — 1Rear Wheel Alignment — 1Steering Column — 1Tire And Wheel — 1Transmitter Battery — 1When Disconnecting Or Reconnecting Battery Terminal — 1When Replacing Or Removing/installing Parts — 1Automatic High Beam Main Switch — 1Automatic High Beam System — 1Driver Monitor Camera — 1Driver Monitor Camera System — 1Driver Monitor Ecu — 1Front Camera — 1Front Camera System — 1Front Radar Sensor System — 1Front Side Radar Sensor — 1Front Side Radar Sensor System — 1Millimeter Wave Radar Sensor — 1Utility — 1Advanced Park — 1Advanced Park Main Switch — 1Amplifier Antenna — 1Audio And Visual System — 1Front Door Speaker — 1Instrument Panel Speaker — 1Microphone — 1Noise Filter — 1Pillar Speaker — 1Radio Antenna Cord (for Back Door) — 1Radio Antenna Cord (for Instrument Panel) — 1Radio Antenna Cord (for Roof) — 1Radio Receiver — 1Rear Door Speaker — 1Roof Antenna — 1Stereo Component Amplifier — 1Stereo Jack Adapter Assembly — 1Window Glass Antenna Wire — 1Back-up Battery — 1Dcm(telematics Transceiver) — 1Manual(sos)switch — 1Safety Connect System — 1Telephone And Gps Antenna (for Front Side) — 1Telephone And Gps Antenna (for Roof Side) — 1Telephone And Gps Antenna Cords — 1Garage Door Opener System (for Digital Inner Mirror) — 1Garage Door Opener System (for Ec Inner Mirror) — 1Blind Spot Monitor Sensor — 1Blind Spot Monitor System — 1Clearance Warning Ecu — 1Intuitive Parking Assist System — 1Panoramic View Monitor Switch — 1Panoramic View Monitor System — 1Parking Assist Ecu — 1Parking Assist Light — 1Parking Assist Monitor System — 1Parking Support Brake System — 1Rear View Monitor System — 1Television Camera (for Front) — 1Television Camera (for Rear) — 1Television Camera (for Side) — 1Ultrasonic Sensor (for Front) — 1Ultrasonic Sensor (for Rear) — 1Brake Actuator — 1Brake Pedal Stroke Sensor — 1Electronically Controlled Brake System — 1Front Speed Sensor — 1Rear Speed Sensor (for Awd) — 1Steering Angle Sensor — 1Brake Booster — 1Brake Fluid — 1Brake Line — 1Brake Pedal — 1Brake System — 1Electric Parking Brake Actuator — 1Electric Parking Brake Switch — 1Electric Parking Brake System — 1Forced Release — 1Front Axle Hub — 1Front Axle Hub Bolt — 1Rear Axle Carrier (for 2wd) — 1Rear Axle Carrier (for Awd) — 1Rear Axle Hub (for 2wd) — 1Rear Axle Hub (for Awd) — 1Rear Axle Hub Bolt — 1Steering Knuckle — 1Drive Shaft System — 1Front Drive Shaft Assembly — 1Rear Drive Shaft Assembly — 1Combination Switch — 1Electronic Shift Lever System — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Oil Seal — 1Hybrid Transaxle System — 1Input Shaft Oil Seal — 1Motor Cable — 1Pa10 Hybrid Vehicle Transaxle — 1Pa10 Manual Parking Lock Release — 1Pa10 Oil Cooler — 1Pb10/pb12 Hybrid Vehicle Transaxle — 1Pb10/pb12 Manual Parking Lock Release — 1Pb10/pb12 Oil Cooler — 1Shift Control Actuator — 1Shift Lever — 1Shift Lever Knob — 1Differential Side Gear Shaft — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Side Gear Oil Seal — 1Motor Cable — 1Rear Traction Motor — 1Coolant (for Engine) — 1Cooling Fan Motor — 1Cooling Fan System — 1Radiator — 1Relay — 1Thermostat — 1Water Pump — 1Canister — 1Egr Cooler — 1Egr Valve — 1Emission Control System — 1Fuel Tank Cap — 1Pcv Valve — 1Purge Valve — 1Vacuum Sensor — 1Air Fuel Ratio Sensor — 1Camshaft Oil Control Valve — 1Camshaft Position Sensor — 1Crankshaft Position Sensor — 1Ecm — 1Engine Coolant Temperature Sensor — 1Heated Oxygen Sensor — 1Ignition Coil And Spark Plug — 1Ignition System — 1Knock Sensor — 1Mass Air Flow Meter — 1Relay — 1Sfi System — 1Throttle Body — 1Camshaft — 1Cylinder Block — 1Cylinder Head — 1Cylinder Head Gasket — 1Engine — 1Engine Assembly — 1Engine Unit — 1Front Crankshaft Oil Seal — 1Rear Crankshaft Oil Seal — 1Fuel Filter — 1Fuel Injector — 1Fuel Pressure Regulator — 1Fuel Pump — 1Fuel Sender Gauge Assembly — 1Fuel System — 1Fuel Tank — 1Air Cleaner Filter Element — 1Exhaust Manifold — 1Exhaust Pipe — 1Intake Manifold — 1Intake System — 1Lubrication System — 1Oil And Oil Filter — 1Oil Pan And Oil Level Sensor — 1Oil Pressure Switch — 1Oil Pump — 1Accelerator Pedal Sensor — 1Battery Blower (for Hev Model) — 1Battery Ecu (for Hev Model) — 1Battery Ecu (for Phev Model) — 1Battery Voltage Sensor (for Phev Model) — 1Charge Cable (for Phev Model) — 1Charge Indicator (for Phev Model) — 1Charge Inlet (for Phev Model) — 1Combination Switch — 1Coolant (for Inverter) — 1Cooler (for Phev Model) — 1Electric Vehicle Charger Assembly (for Phev Model) — 1Frame Wire (for Hev Model) — 1Frame Wire (for Phev Model) — 1Heater Relay (for Phev Model) — 1Hv Battery (for Hev Model) — 1Hv Battery (for Phev Model) — 1Hv Battery Heater (for Phev Model) — 1Hv Battery Stack (for Phev Model) — 1Hv Relay Assembly (for Hev Model) — 1Hv Relay Assembly (for Phev Model) — 1Hybrid Battery System (for 2zr-fxe) — 1Hybrid Battery System (for M20a-fxs) — 1Hybrid Battery System (for Phev Model) — 1Hybrid Vehicle Control Ecu — 1Inverter With Converter (for Hev Model) — 1Motor Generator Control System (for 2zr-fxe) — 1Plug-in Charge Control System (for Phev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Service Plug Grip (for Hev Model) — 1Sub Radiator — 1Water Pump With Motor — 1Auxiliary Battery — 1Battery Current Sensor — 1Charging System — 1Solar Charging System — 1Solar Control Unit — 1Solar Roof — 1Can Communication System (for Hev Model) — 1Lin Communication System — 1Network Gateway Ecu — 1Integration Control Supply — 1Main Body Ecu — 1Power Integration System — 1Sub Battery System — 1Power Steering Ecu — 1Power Steering System — 1Heated Steering Wheel Controller — 1Heated Steering Wheel System — 1Steering Column Assembly — 1Steering Heater Switch — 1Steering Pad Switch — 1Steering System — 1Steering Wheel — 1Front Lower Ball Joint — 1Front Lower Suspension Arm (for 2zr-fxe Lh Side) — 1Front Lower Suspension Arm (for 2zr-fxe Rh Side) — 1Front Lower Suspension Arm (for M20a-fxs) — 1Front Shock Absorber — 1Front Stabilizer Bar — 1Front Suspension Member — 1Rear Coil Spring — 1Rear Lower Arm (for Awd Lh Side) — 1Rear Lower Arm (for Awd Rh Side) — 1Rear Lower Arm (for Hev Model 2wd) — 1Rear Lower Arm (for Phev Model) — 1Rear Shock Absorber — 1Rear Stabilizer Bar — 1Rear Suspension Member (for 2wd) — 1Rear Suspension Member (for Awd) — 1Rear Trailing Arm — 1Rear Upper Arm — 1Tire And Wheel System — 1Tire Repair Seal — 1Tire Pressure Warning Receiver — 1Tire Pressure Warning System — 1Tire Pressure Warning Valve — 1Acoustic Vehicle Alerting System — 1Vehicle Approaching Speaker — 1Vehicle Approaching Speaker Ecu — 1Back Door — 1Back Door Closer Ecu — 1Back Door Opener Switch — 1Back Door Support — 1Back Door Weatherstrip — 1Charge Lid Courtesy Switch — 1Charge Lid Opener Motor Assembly — 1Charge Lid Opener System — 1Charge Lid Opener Unit — 1Front Door — 1Front Door Opening Trim Weatherstrip — 1Fuel Lid Opener Motor Assembly — 1Fuel Lid Opener Switch — 1Fuel Lid Opener System — 1Hood — 1Hood Lock Control Cable Assembly — 1Power Back Door Closer Switch — 1Power Back Door Control Switch — 1Power Back Door Drive Unit — 1Power Back Door System — 1Power Back Door Touch Sensor — 1Power Back Door Warning Buzzer — 1Rear Door — 1Rear Door Opening Trim Weatherstrip — 1Reserve Lock Switch — 1Front Bumper — 1Front Door Belt Moulding — 1Front Door Window Frame Moulding — 1Front Fender — 1Front Pillar Upper Cover — 1Grille Shutter — 1Grille Shutter System — 1Name Plate — 1Quarter Garnish — 1Rear Bumper — 1Rear Door Belt Moulding — 1Rear Door Window Frame Moulding — 1Rear Wheel House Plate — 1Rocker Panel Moulding — 1Roof Drip Side Finish Moulding — 1Roof Garnish — 1Wheel Opening Moulding (for Front Side) — 1Wheel Opening Moulding (for Rear Side) — 1Windshield Outside Moulding — 1Horn — 1Horn System — 1Relay — 1Automatic Light Control Sensor — 1Back-up Light Assembly — 1Charge Lid Light — 1Front Marker Light — 1Hazard Warning Switch — 1Headlight Assembly — 1Headlight Dimmer Switch — 1Headlight Leveling Switch — 1High Mounted Stop Light Assembly — 1Illumination Light Assembly — 1License Plate Light Assembly — 1Lighting System — 1Rear Combination Light Assembly — 1Rear Light Assembly — 1Rear Side Marker Light Assembly — 1Relay — 1Side Turn Signal Light Assembly — 1Stop Light Switch — 1Switch Housing — 1Outer Mirror Switch — 1Outer Rear View Mirror — 1Outer Rear View Mirror Cover — 1Outer Rear View Mirror Glass — 1Power Mirror Control System — 1Back Door Glass — 1Front Passenger Side Power Window Switch — 1Power Window Control System — 1Power Window Master Switch — 1Power Window Regulator Motor (for Front Door) — 1Power Window Regulator Motor (for Rear Door) — 1Rear Power Window Switch — 1Relay — 1Roof Window Fix Glass — 1Window Defogger System — 1Windshield Deicer Switch — 1Windshield Deicer System — 1Windshield Glass — 1Front Wiper Motor — 1Rain Sensor — 1Relay — 1Washer Motor — 1Washer Nozzle (for Front Side) — 1Washer Nozzle (for Rear Television Camera) — 1Wiper And Washer System — 1Wiper Ecu — 1Wiper Switch — 1Back Door Lock — 1Door Control Receiver — 1Door Control Switch — 1Door Control Transmitter — 1Door Lock Release Motor (for Rear Side) — 1Door Outside Handle (for Rear Side) — 1Front Door Lock — 1Power Door Lock Control System — 1Rear Door Lock — 1Transmitter Battery — 1Wireless Door Lock Control System — 1Accumulator — 1Air Conditioning Amplifier — 1Air Conditioning Panel — 1Air Conditioning Pressure Sensor — 1Air Conditioning Unit — 1Ambient Temperature Sensor — 1Blower Unit — 1Condenser (for Hev Model) — 1Condenser (for Phev Model) — 1Discharge Temperature Sensor — 1Electric Expansion Valve (cooling) — 1Electric Expansion Valve (heating) — 1Evaporator Pipe Temperature Sensor — 1Evaporator Pressure Regulator — 1Front Blower Motor — 1Front Evaporator Front Solenoid Valve — 1Air Conditioning System (for Hev Model) — 1Front Evaporator Temperature Sensor — 1Heat Exchanger Temperature Sensor — 1Heat Pump Ecu — 1High Pressure Magnetic Valve — 1Humidity Sensor — 1Internal Condenser Temperature Sensor — 1Low Pressure Magnetic Valve — 1Refrigerant (for Hfc-134a(r134a)) — 1Refrigerant Line (for Hev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Room Temperature Sensor — 1Solar Sensor — 1Floor Carpet — 1Front Console Box — 1Instrument Panel Safety Pad — 1Roof Headlining — 1Roof Sunshade — 1Ambient Light (for Driver Side) — 1Ambient Light (for Front Passenger Side) — 1Back Door Courtesy Switch — 1Footwell Light — 1Glove Box Light — 1Lighting System — 1Luggage Compartment Room Light — 1Personal Light — 1Room Light — 1Vanity Light — 1Vanity Light Switch — 1Combination Meter — 1Meter / Gauge System — 1Trip Switch — 1Digital Inner Mirror — 1Digital Rear-view Mirror System — 1Inner Mirror Monitor Camera — 1Inner Rear View Mirror (w/o Ec Mirror) — 1Accessory Power Outlet System — 1Power Outlet Socket (for Console Box Front Side) — 1Power Outlet Socket (for Console Box Rear Side) — 1Power Outlet Socket (for Console Box) — 1Power Outlet Socket (for Luggage Compartment) — 1Power Outlet Switch — 1Wireless Charger Assembly — 1Wireless Charging System — 1Climate Control Seat System — 1Front Power Seat Control System (w/ Memory) — 1Front Power Seat Motor Assembly — 1Front Seat Assembly (for Power Seat) — 1Front Seat Cushion Heater (for Power Seat) — 1Front Seatback Heater (for Power Seat) — 1Lumbar Support Adjuster Assembly — 1Power Seat Control Ecu — 1Power Seat Switch — 1Power Seat Track Rail Assembly — 1Rear Seat Assembly — 1Rear Seat Cushion Heater — 1Rear Seat Reminder System — 1Rear Seatback Heater — 1Seat Heater Control — 1Seat Heater Switch (for Front Seat) — 1Seat Heater Switch (for Rear Side) — 1Seat Heater System — 1Seat Memory Switch — 1Child Restraint Seat Anchor Bracket — 1Front Seat Inner Belt Assembly — 1Front Seat Outer Belt Assembly — 1Occupant Detection Sensor (for Front Passenger Side) — 1Rear Center Seat Outer Belt Assembly — 1Rear Seat Inner Belt Assembly (for Rh Side) — 1Rear Seat Outer Belt Assembly — 1Seat Belt Warning System (w/ Occupant Classification System) — 1Tongue Plate Stopper — 1Airbag System — 1Center Airbag Sensor Assembly — 1Curtain Shield Airbag Assembly — 1Front Airbag Sensor — 1Front Passenger Airbag Assembly — 1Front Seat Side Airbag Assembly — 1Inspection After Collision — 1Knee Airbag Assembly — 1Occupant Classification System — 1Rear Seat Side Airbag Assembly — 1Side Airbag Sensor (for Center Pillar) — 1Side Airbag Sensor (for Front Door) — 1Spiral Cable — 1Steering Pad — 1Certification Ecu — 1Digital Key Ecu — 1Digital Key Receiver (for Front Floor) — 1Digital Key Receiver (for Outside Luggage Compartment) — 1Digital Key Receiver (for Rear Door) — 1Digital Key System — 1Electrical Key Oscillator (for Front Floor) — 1Electrical Key Oscillator (for Outside Luggage Compartment) — 1Electrical Key Oscillator (for Rear Floor) — 1Engine Hood Courtesy Switch — 1Id Code Box — 1Smart Key System (for Start Function) — 1
9steps
~54min
5/5difficulty
Done 0 of 9
  • Precaution
  • Parts Location
  • System Diagram
  • System Description
  • How To Proceed With Troubleshooting
  • Operation Check
  • Initialization
  • Problem Symptoms Table
  • Terminals Of Ecu
  • Freeze Frame Data
  • Fail-safe Chart
  • Data List / Active Test
  • Diagnostic Trouble Code Chart
  • VEHICLE CONTROL HISTORY (RoB)
  • Passenger Seat Occupant Classification Sensor "A" Signal Bias Level Out of Range / Zero Adjustment Failure (B00C028)
  • Passenger Seat Occupant Classification Sensor "A" Signal (some circuit quantity, reported via serial data) Invalid (B00C086)
  • Passenger Seat Occupant Classification Sensor "A" Missing Message (B00C087)
  • Passenger Seat Occupant Classification Sensor "A" Component Internal Failure (B00C096)
  • Load Sensor for Occupant Detection System Circuit Short to Battery (B179312)
  • Load Sensor for Occupant Detection System Circuit Voltage Below Threshold (B179316)
  • Trouble in Passenger Airbag ON/OFF Indicator
  • LIN Communication Circuit

Precaution

PRECAUTION

GENERAL PRECAUTION

(a) The following conditions may be interpreted as a malfunction even though they are normal operation:

  1. An object is placed on the front passenger seat and the system judges that an adult is seated. As the occupant classification system detects and classifies occupants based on weight, the system may detect an object placed on the seat cushion as an adult front passenger depending on its weight.
  2. Pressure is applied to the front passenger seat and the system judges that an adult is seated. As the occupant classification system detects and classifies occupants based on weight, the system may detect an adult front passenger if pressure is applied to the seat cushion by hands, etc.
  3. Illumination of the passenger airbag ON/OFF indicator does not change immediately after a front passenger is seated or leaves the Toyota Prius vehicle. To prevent the classification judgment from changing when a front passenger changes their seating posture, a certain amount of time is required to detect and classify an occupant when the calculated weight changes. Therefore, there will be a time lag between when a front passenger is seated or leaves the Toyota Prius vehicle and when the system detects the occupant.

(b) The zero point of the occupant classification sensors may deviate. To ensure sensor accuracy, be sure to perform Zero Point Calibration.

Click here

PRECAUTIONS FOR DISCONNECTING CABLE FROM NEGATIVE (-) AUXILIARY BATTERY TERMINAL

NOTICE:

  • After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

    Click here

    HINT:

    When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

    Click here

Parts Location

PARTS LOCATION

ILLUSTRATION

*1

BRAKE ACTUATOR ASSEMBLY

- NO. 2 SKID CONTROL ECU

*2

MAP LIGHT ASSEMBLY

- PASSENGER AIRBAG ON/OFF INDICATOR

ILLUSTRATION

*1

AIRBAG ECU ASSEMBLY

*2

FRONT SEAT INNER BELT ASSEMBLY RH

- PASSENGER SEAT BUCKLE SWITCH

*3

FRONT SEAT ADJUSTER ASSEMBLY RH

*4

FRONT OCCUPANT CLASSIFICATION SENSOR LH

*5

REAR OCCUPANT CLASSIFICATION SENSOR LH

*6

DLC3

*7

POWER DISTRIBUTION BOX ASSEMBLY

- A/BAG-IGR FUSE

-

-

System Diagram

SYSTEM DIAGRAM

Communication Table

Transmitting ECU / Parts

(Transmitter)

Receiving ECU

(Receiver)

Signal

Communication Method

Passenger Seat Buckle Switch (Front Seat Inner Belt Assembly RH)

Airbag ECU Assembly

Front passenger side buckle switch signal

Direct line

Passenger Airbag ON/OFF Indicator (Map Light Assembly)

Airbag ECU Assembly

  • Passenger airbag indicator ON signal
  • Passenger airbag indicator OFF signal

Front Occupant Classification Sensor LH

Airbag ECU Assembly

Occupant load for front passenger signal

LIN

Rear Occupant Classification Sensor LH

Airbag ECU Assembly

No. 2 Skid Control ECU (Brake Actuator Assembly)

Airbag ECU Assembly

  • Toyota Prius Vehicle speed signal
  • Acceleration signal

CAN

System Description

SYSTEM DESCRIPTION

GENERAL

(a) The airbag ECU assembly estimates the weight of an occupant based on signals received from the 2 occupant classification sensors. The airbag ECU assembly determines whether the front passenger seat is occupied and classifies the occupant based on the estimated weight, front passenger side buckle switch state, acceleration sensor signal and Toyota Prius vehicle speed signal.

(b) The airbag ECU assembly controls the operation of the passenger airbag ON/OFF indicator and restricts the operation of the instrument panel passenger airbag assembly.

How To Proceed With Troubleshooting

HINT:

  • Use the following procedure to troubleshoot the occupant classification system.
  • *: Use the GTS.

PROCEDURE

  1. Toyota Prius Vehicle BROUGHT TO WORKSHOP

NEXT
  1. CUSTOMER PROBLEM ANALYSIS

(a) Confirm problem symptoms.

Click here

NEXT
  1. INSPECT AUXILIARY BATTERY VOLTAGE

(a) Measure the auxiliary battery voltage with the ignition switch off.

Standard Voltage:

11 to 14 V

HINT:

  • A simple method to determine whether the auxiliary battery is discharged is to operate the horn.
  • If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding.

(b) Check the fuses and relays.

(c) Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.

NEXT
  1. CHECK CAN COMMUNICATION SYSTEM*

(a) Using the GTS, check that the CAN communication system is functioning normally.

OK:

CAN communication system is functioning normally.

HINT:

  • Refer to CAN Bus Check in CAN Communication System.

    for HEV Model: Click here

    for PHEV Model: Click here

  • The airbag ECU assembly is connected to the CAN communication system. Therefore, before starting troubleshooting, make sure to check that there are no malfunctions in the CAN communication system.
NG

GO TO CAN COMMUNICATION SYSTEM

for HEV Model: Click here

for PHEV Model: Click here

OK
  1. CHECK PASSENGER AIRBAG ON/OFF INDICATOR

(a) Refer to Operation Check.

Click here

NEXT
  1. CHECK DTC*

(a) Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes

HINT:

Record or print DTCs if necessary.

Result

Proceed to

No DTCs are output

A

Airbag system DTCs are output

B

Occupant classification system DTCs are output

C

A

GO TO PROBLEM SYMPTOMS TABLE

B

GO TO AIRBAG SYSTEM

C
  1. CLEAR DTC*

NOTICE:

Make sure to record any output Freeze Frame Data and Toyota Prius Vehicle Control History (RoB) codes before clearing them and checking the DTC again.

(a) Clear the DTCs.

Body Electrical > SRS Airbag > Clear DTCs
NEXT
  1. CHECK DTC*

(a) Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes

HINT:

Record or print DTCs if necessary.

OK:

DTCs are not output.

NG

GO TO DIAGNOSTIC TROUBLE CODE CHART

OK
  1. CHECK FOR Toyota Prius Vehicle CONTROL HISTORY*

(a) Check for Vehicle Control History (RoB).

Body Electrical > SRS Airbag > Utility

Vehicle Control History (RoB)

Result

Proceed to

Toyota Prius Vehicle Control History (RoB) is not output

A

Vehicle Control History (RoB) is output

B

A

GO TO PROBLEM SYMPTOMS TABLE

B
  1. CLEAR Toyota Prius Vehicle CONTROL HISTORY*

NOTICE:

Make sure to record any output Freeze Frame Data and Vehicle Control History (RoB) codes before clearing them and checking the DTC again.

(a) Clear the Vehicle Control History (RoB).

Body Electrical > SRS Airbag > Utility

Toyota Prius Vehicle Control History (RoB)

NEXT
  1. CHECK FOR Toyota Prius Vehicle CONTROL HISTORY*

(a) Check for Vehicle Control History (RoB).

Body Electrical > SRS Airbag > Utility

Vehicle Control History (RoB)

Result

Proceed to

Toyota Prius Vehicle Control History (RoB) is not output

A

Vehicle Control History (RoB) is output

B

A

USE SIMULATION METHOD TO CHECK

B

GO TO Toyota Prius Vehicle CONTROL HISTORY

Operation Check

OPERATION CHECK

PRECAUTION FOR OPERATION CHECK

CAUTION:

Use the correct procedure to replace the airbag parts.

CHECK SRS WARNING LIGHT

(a) Primary check

(1) Turn the ignition switch to ON and check that the SRS warning light turns on.

(2) Turn the ignition switch off. Wait for at least 2 seconds, and then turn the ignition switch to ON. The SRS warning light comes on for approximately 6 seconds and diagnosis of the airbag system (including the seat belt pretensioners) is performed.

NOTICE:

Turn the ignition switch off when the auxiliary battery is connected.

HINT:

  • If the SRS warning light remains on for approximately 6 seconds or more after the ignition switch has been turned to ON, there may be a malfunction with the airbag system.
  • If the warning light occasionally turns on approximately 6 seconds or more after the ignition switch has been turned to ON, there may be a short to B, short to ground or an open in the SRS warning light circuit.
  • If the warning light illuminates after turning the ignition switch off or to ACC, there may be a malfunction in the power source circuit or combination meter assembly.
  • The SRS warning light turns off, and then turns on. This blinking pattern indicates a source voltage drop. The SRS warning light turns off 6 to 10 seconds after the source voltage returns to normal.

FUNCTION OF PASSENGER AIRBAG ON/OFF INDICATOR

(a) Initial check

(1) Turn the ignition switch to ON.

(2) The passenger airbag ON/OFF indicator comes on for approximately 4 seconds, and then goes off for approximately 2 seconds.

(3) Approximately 6 seconds after the ignition switch is turned to ON, the passenger airbag ON/OFF indicator will indicate ON/OFF depending on the following conditions.

Indicator Operation

Front Passenger Seat Condition

Passenger Airbag ON/OFF Indicator

SRS Warning Light

ON Indicator

OFF Indicator

Vacant

OFF

ON

OFF

Adult*1 is seated

ON

OFF

OFF

Child*2 is seated

ON or OFF*2

OFF or ON*2

OFF

Child restraint system is installed

OFF

ON

OFF

Occupant classification system failure

OFF

ON

ON

  • *1: The system judges a person of average adult weight or more as an adult. If a smaller adult sits in the front passenger seat, the system may not recognize them as an adult depending on their physique and posture.
  • *2: The system may not recognize a child or a child in a child restraint system as a child depending on factors such as the positioning of the child restraint system or the child's physique or posture.

HINT:

  • The timing chart below shows the operation of the passenger airbag ON/OFF indicator. Use the chart to check the indicator light circuit.
  • When the occupant classification system has trouble, both the SRS warning light and passenger airbag ON/OFF indicator ("OFF") come on. In this case, check for DTCs for "Airbag System" first.

Initialization

INITIALIZATION

DESCRIPTION

(a) The zero point of the occupant classification sensors may deviate in the following situations. To ensure sensor accuracy, be sure to perform Zero Point Calibration.

  1. The airbag ECU assembly is replaced.

    HINT:

    As the zero point is not automatically stored in a new airbag ECU assembly, it is necessary to perform zero point calibration after replacing the airbag ECU assembly.

  2. Accessories (seatback tray, seat cover, etc.) are installed or removed.

    HINT:

    As the weight of accessories will be added or decreased to the weight of the occupant, the system will not be able to perform classification accurately.

  3. The front passenger seat is removed from the Toyota Prius vehicle.

    HINT:

    As the seat frame will warp slightly when the bolts that are used to install the front passenger seat are tightened, the load applied to the occupant classification sensor will change and the system will not be able to perform classification accurately.

  4. Any of the bolts that are used to install the front passenger seat are removed and reinstalled.

    HINT:

    As the seat frame will warp slightly when the bolts that are used to install the front passenger seat are tightened, the load applied to the occupant classification sensor will change and the system will not be able to perform classification accurately.

  5. The passenger airbag ON/OFF indicator ("ON") illuminates when the front passenger seat is not occupied or the airbag OFF indicator illuminates when the front passenger seat is occupied (by an adult).

    HINT:

    If any load or pressure is applied to the occupant classification sensors, the system will not be able to perform classification accurately.

  6. An occupant classification sensor collision detection DTC is output due to an accident or a collision.

    HINT:

    If the seat frame or Toyota Prius vehicle floor has become deformed and additional pressure is applied to the occupant classification sensor, the system will not be able to perform classification accurately.

NOTICE:

Make sure that the front passenger seat is not occupied before performing the operation.

ZERO POINT CALIBRATION

(a) Zero point calibration procedure

(1) Check that all of the following conditions are met:

  • The Toyota Prius vehicle is parked on a level surface.
  • No objects are placed on the front passenger seat.
  • No objects are touching the front passenger seat.

(2) Adjust the seat position according to the table below.

Adjustment Item

Position

Slide Direction

Rearmost position

Headrest Height

Lowest position

Recline Angle

Upright position

Seat Lifter Height

Lowest position

(3) Perform zero point calibration by following the prompts on the GTS screen.

Body Electrical > SRS Airbag > Utility

Occupant Detection Sensor Zero Point Calibration

OK:

"Occupant Detection Sensor Zero Point Calibration is complete." is displayed.

(4) Clear the Toyota Prius Vehicle Control History (RoB).

Body Electrical > SRS Airbag > Utility

Vehicle Control History (RoB)

(5) Check for Vehicle Control History (RoB).

Body Electrical > SRS Airbag > Utility

Toyota Prius Vehicle Control History (RoB)

OK:

X20D0 is not output.

HINT:

  • Refer to the GTS operator's manual for further details.
  • If Occupant Detection Sensor Zero Point Calibration does not complete normally, check the Error Code List to determine the cause of malfunction. Error Code List

    Error Code

    Item Name

    Cause

    Countermeasure

    01

    Out of FI Load Sensor Upper Limit Standard

    When any of the following conditions is detected:
    • The sensor load value before learning is not as specified (upper limit exceeded)
    • The sensor load value after learning is not as specified (upper limit exceeded)
    Check for the following
    1. Check whether the Toyota Prius vehicle and seat are subject to vibration or a load
    2. Check front seat assembly RH installation
    3. Perform Occupant Detection Sensor Zero Point Calibration again

      HINT:

      If the error code is output again, replace the front seat adjuster assembly RH (occupant classification sensor).

    02

    Out of FI Load Sensor Lower Limit Standard

    When any of the following conditions is detected:
    • The sensor load value before learning is not as specified (below lower limit)
    • The sensor load value after learning is not as specified (below lower limit)
    Check for the following
    1. Check whether the Toyota Prius vehicle and seat are subject to vibration or a load
    2. Check front seat assembly RH installation
    3. Perform Occupant Detection Sensor Zero Point Calibration again

      HINT:

      If the error code is output again, replace the front seat adjuster assembly RH (occupant classification sensor).

    03

    Out of RI Load Sensor Upper Limit Standard

    When any of the following conditions is detected:
    • The sensor load value before learning is not as specified (upper limit exceeded)
    • The sensor load value after learning is not as specified (upper limit exceeded)
    Check for the following
    1. Check whether the Toyota Prius vehicle and seat are subject to vibration or a load
    2. Check front seat assembly RH installation
    3. Perform Occupant Detection Sensor Zero Point Calibration again

      HINT:

      If the error code is output again, replace the front seat adjuster assembly RH (occupant classification sensor).

    04

    Out of RI Load Sensor Lower Limit Standard

    When any of the following conditions is detected:
    • The sensor load value before learning is not as specified (below lower limit)
    • The sensor load value after learning is not as specified (below lower limit)
    Check for the following
    1. Check whether the Toyota Prius vehicle and seat are subject to vibration or a load
    2. Check front seat assembly RH installation
    3. Perform Occupant Detection Sensor Zero Point Calibration again

      HINT:

      If the error code is output again, replace the front seat adjuster assembly RH (occupant classification sensor).

    10

    Nonvolatile Memory Storage Failure

    When a memory malfunction caused by either of the following is detected:
    • Writing failure
    • IGR low voltage (below 8 V)
    Check for the following
    1. Check for DTC
    2. Check Toyota Prius Vehicle Control History (RoB)
    3. Measure IGR terminal voltage

      HINT:

      If below 8 V, check the power source circuit.

    4. Perform Occupant Detection Sensor Zero Point Calibration again

      HINT:

      If the error code is output again, replace the airbag ECU assembly.

    11

    Zero Point Learning Timeout

    Occupant Detection Sensor Zero Point Calibration does not complete within 2 seconds (within the specified number of seconds)

    Check for the following
    1. Clear the Toyota Prius Vehicle Control History (RoB)
    2. Check Vehicle Control History (RoB)
    3. Check whether the vehicle and seat are subject to vibration or a load
    4. Check front seat assembly RH installation
    5. Perform Occupant Detection Sensor Zero Point Calibration again

      HINT:

      If the error code is output again, replace the airbag ECU assembly.

    13

    FI Load Sensor Malfunction

    When a load sensor malfunction is detected

    Check for the following
    1. Check for DTC
    2. Perform Occupant Detection Sensor Zero Point Calibration again

      HINT:

      If the error code is output again, replace the front seat adjuster assembly RH (occupant classification sensor).

    14

    RI Load Sensor Malfunction

    When a load sensor malfunction is detected

    Check for the following
    1. Check for DTC
    2. Perform Occupant Detection Sensor Zero Point Calibration again

      HINT:

      If the error code is output again, replace the front seat adjuster assembly RH (occupant classification sensor).

    17

    FI LIN Communication Lost

    When a communication malfunction with the load sensor is detected

    Check for the following
    1. Check for DTC
    2. Perform Occupant Detection Sensor Zero Point Calibration again

      HINT:

      If the error code is output again, Refer to "LIN Communication Circuit"

    18

    RI LIN Communication Lost

    When a communication malfunction with the load sensor is detected

    Check for the following
    1. Check for DTC
    2. Perform Occupant Detection Sensor Zero Point Calibration again

      HINT:

      If the error code is output again, Refer to "LIN Communication Circuit"

    21

    ECU Malfunction

    When an airbag ECU assembly malfunction is detected

    Check for the following
    1. Check for DTC
    2. Perform Occupant Detection Sensor Zero Point Calibration again

      HINT:

      If the error code is output again, replace the airbag ECU assembly.

    22

    IGR Voltage Malfunction

    When IGR voltage (below 8 V or 16 V or higher) is detected

    Check for the following
    1. Check Toyota Prius Vehicle Control History (RoB)
    2. Measure IGR terminal voltage

      HINT:

      If below 8 V or 16 V or higher, check the power source circuit.

    23

    Load Unstable

    When any of the following conditions is detected:
    • The Toyota Prius vehicle and seat are subject to vibration or a load
    • Sensor malfunction
    Check for the following
    1. Check whether the vehicle and seat are subject to vibration or a load
    2. Perform Occupant Detection Sensor Zero Point Calibration again

      HINT:

      If the error code is output again, replace the front seat adjuster assembly RH (occupant classification sensor).

Problem Symptoms Table

PROBLEM SYMPTOMS TABLE

HINT:

  • Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
  • Inspect the fuses and relays related to this system before inspecting the suspected areas below.
Occupant Classification System

Symptom

Suspected Area

Link

The passenger airbag ON/OFF indicator indication differs from the indication patterns of "Indicator Operation"

Click here

Trouble in passenger airbag ON/OFF indicator

Terminals Of Ecu

TERMINALS OF ECU

AIRBAG ECU ASSEMBLY

Terminal No.

Terminal Symbol

Destination

K1-32

E2

Ground

K1-33

E1

K1-34

P-AB

Passenger airbag ON/OFF indicator (Map light assembly)

K1-35

PAON

K1-36

IGR

A/BAG-IGR fuse

R1-18

GNDR

Passenger seat buckle switch (Front seat inner belt assembly RH)

R1-27

RBE

R1-24

SVC

Occupant classification sensor (Front seat adjuster assembly RH)

R1-31

SGD

R1-32

SIG

Freeze Frame Data

FREEZE FRAME DATA

DESCRIPTION

(a) When an occupant classification system DTC is stored, the airbag ECU assembly stores the current vehicle (ECU or sensor) state as Freeze Frame Data.

CHECK FREEZE FRAME DATA

(a) Select a DTC to display the freeze frame data.

Body Electrical > SRS Airbag > Trouble Codes

(b) Check the freeze frame data for the output DTC.

CHECK FREEZE FRAME DATA

(a) Read the freeze frame data recorded when the DTC was stored.

Body Electrical > SRS Airbag

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Total Distance Traveled

-

-

-

Not applicable

Total Distance Traveled - Unit

-

-

-

Not applicable

Load Sensor Total Load Value Information

Total weight information

-606.952 to 838.088 kg

Current value displayed

-

Front Inner Load Sensor Load Value Information

Front left sensor weight information

-151.738 to 209.522 kg

Current value displayed

-

Rear Inner Load Sensor Load Value Information

Rear left sensor weight information

-151.738 to 209.522 kg

Current value displayed

-

Judgment Result for Occupant Detection System (Occupant of Passenger Seat)

Front passenger classification

Unknown, Nothing, Child, Prohibition, Male or Female

Nothing: Seat is vacant

Child: Child is seated

Male: Male is seated

Female: Female is seated

-

Judgment Result for Occupant Detection System (Seat Belt Warning of Passenger Seat)

Passenger detection for seat belt warning system

Not Seating or Seating

Not Seating: Seat is vacant

Seating: Seat is occupied

-

Judgment Result for Occupant Detection System (Buckle Switch of Passenger Seat)

Front passenger side buckle switch

Unknown, Buckle, Unbuckle or Malfunction

Buckle: Front passenger seat belt is fastened

Unbuckle: Front passenger seat belt is not fastened

Malfunction: Front passenger seat belt is malfunctioning

-

Fail-safe Chart

FAIL-SAFE CHART

FAIL-SAFE FUNCTION

(a) The following chart shows the status of the front passenger SRS items and passenger airbag ON/OFF indicator operation under failure condition.

Passenger Airbag ON/OFF Indicator

Front Passenger SRS Item

ON Indicator

OFF Indicator

Instrument Panel Passenger Airbag Assembly

Front Seat Airbag Assembly RH

Curtain Shield Airbag Assembly RH

Front Seat Outer Belt Assembly RH

OFF

ON

X

○

○

○

  • ○: Deployable
  • X: Not deployable

Data List / Active Test

DATA LIST / ACTIVE TEST

DATA LIST

HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

(a) Read the Data List according to the display on the GTS.

Body Electrical > SRS Airbag > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Total Distance Traveled

-

-

-

Not applicable

Total Distance Traveled - Unit

-

-

-

Not applicable

Load Sensor Total Load Value Information

Total weight information

-606.952 to 838.088 kg

Current value displayed

-

Front Inner Load Sensor Load Value Information

Front left sensor weight information

-151.738 to 209.522 kg

Current value displayed

-

Rear Inner Load Sensor Load Value Information

Rear left sensor weight information

-151.738 to 209.522 kg

Current value displayed

-

Judgment Result for Occupant Detection System (Occupant of Passenger Seat)

Front passenger classification

Unknown, Nothing, Child, Prohibition, Male or Female

Nothing: Seat is vacant

Child: Child is seated

Male: Male is seated

Female: Female is seated

-

Judgment Result for Occupant Detection System (Seat Belt Warning of Passenger Seat)

Passenger detection for seat belt warning system

Not Seating or Seating

Not Seating: Seat is vacant

Seating: Seat is occupied

-

Judgment Result for Occupant Detection System (Buckle Switch of Passenger Seat)

Front passenger side buckle switch

Unknown, Buckle, Unbuckle or Malfunction

Buckle: Front passenger seat belt is fastened

Unbuckle: Front passenger seat belt is not fastened

Malfunction: Front passenger seat belt is malfunctioning

-

Seat Factory Zero Point Learning History (Front Inner Load Sensor Learning Executed/Unexecuted)

-

-

-

Not applicable

Seat Factory Zero Point Learning History (Front Inner Load Sensor Learning Value)

-

-

-

Not applicable

Seat Factory Zero Point Learning History (Rear Inner Load Sensor Learning Executed/Unexecuted)

-

-

-

Not applicable

Seat Factory Zero Point Learning History (Rear Inner Load Sensor Learning Value)

-

-

-

Not applicable

Toyota Prius Vehicle Plant Zero Point Learning History (Front Inner Load Sensor Learning Executed/Unexecuted)

-

-

-

Not applicable

Toyota Prius Vehicle Plant Zero Point Learning History (Front Inner Load Sensor Learning Value)

-

-

-

Not applicable

Toyota Prius Vehicle Plant Zero Point Learning History (Rear Inner Load Sensor Learning Executed/Unexecuted)

-

-

-

Not applicable

Toyota Prius Vehicle Plant Zero Point Learning History (Rear Inner Load Sensor Learning Value)

-

-

-

Not applicable

Dealer Zero Point Learning History (Front Inner Load Sensor Learning Executed/Unexecuted)

-

-

-

Not applicable

Dealer Zero Point Learning History (Front Inner Load Sensor Learning Value)

-

-

-

Not applicable

Dealer Zero Point Learning History (Rear Inner Load Sensor Learning Executed/Unexecuted)

-

-

-

Not applicable

Dealer Zero Point Learning History (Rear Inner Load Sensor Learning Value)

-

-

-

Not applicable

Front Inner Load Sensor Serial No. - Production Year (Last Two Digits of the Year)

-

-

-

Not applicable

Front Inner Load Sensor Serial No. - Production Month

-

-

-

Not applicable

Front Inner Load Sensor Serial No. - Production Date

-

-

-

Not applicable

Front Inner Load Sensor Serial No. - Sensor No.

-

-

-

Not applicable

Front Inner Load Sensor Serial No. - Line No.

-

-

-

Not applicable

Front Inner Load Sensor Serial No. - Serial No.

-

-

-

Not applicable

Rear Inner Load Sensor Serial No. - Production Year (Last Two Digits of the Year)

-

-

-

Not applicable

Rear Inner Load Sensor Serial No. - Production Month

-

-

-

Not applicable

Rear Inner Load Sensor Serial No. - Production Date

-

-

-

Not applicable

Rear Inner Load Sensor Serial No. - Sensor No.

-

-

-

Not applicable

Rear Inner Load Sensor Serial No. - Line No.

-

-

-

Not applicable

Rear Inner Load Sensor Serial No. - Serial No.

-

-

-

Not applicable

Diagnostic Trouble Code Chart

DIAGNOSTIC TROUBLE CODE CHART

Occupant Classification System

DTC No.

Detection Item

DTC Output from

Priority

Link

B00C028

Passenger Seat Occupant Classification Sensor "A" Signal Bias Level Out of Range / Zero Adjustment Failure

SRS Airbag

A

B00C086

Passenger Seat Occupant Classification Sensor "A" Signal (some circuit quantity, reported via serial data) Invalid

SRS Airbag

A

B00C087

Passenger Seat Occupant Classification Sensor "A" Missing Message

SRS Airbag

A

B00C096

Passenger Seat Occupant Classification Sensor "A" Component Internal Failure

SRS Airbag

A

B00C228

Passenger Seat Occupant Classification Sensor "C" Signal Bias Level Out of Range / Zero Adjustment Failure

SRS Airbag

A

B00C286

Passenger Seat Occupant Classification Sensor "C" Signal (some circuit quantity, reported via serial data) Invalid

SRS Airbag

A

B00C287

Passenger Seat Occupant Classification Sensor "C" Missing Message

SRS Airbag

A

B00C296

Passenger Seat Occupant Classification Sensor "C" Component Internal Failure

SRS Airbag

A

B179312

Load Sensor for Occupant Detection System Circuit Short to Battery

SRS Airbag

A

B179316

Load Sensor for Occupant Detection System Circuit Voltage Below Threshold

SRS Airbag

A

B179317

Load Sensor for Occupant Detection System Circuit Voltage Above Threshold

SRS Airbag

A

VEHICLE CONTROL HISTORY (RoB)

VEHICLE CONTROL HISTORY (RoB)

NOTICE:

When checking the vehicle control history, make sure to record the output histories. Then, remove the histories and recheck the output histories again.

CHECK VEHICLE CONTROL HISTORY

(a) According to the display on the GTS, check the Toyota Prius Vehicle Control History (RoB).

Body Electrical > SRS Airbag > Utility

Vehicle Control History (RoB)

Vehicle Control History (RoB)

Warning Light

Code

Tester Display

Measurement Item

Diagnostic Note

SRS warning light illuminated

X204A

Acceleration Sensor Malfunction

Recorded when airbag ECU assembly received a malfunction signal of accelerator sensor output from skid control ECU.

Refer to How to Proceed with Troubleshooting in Electronically Controlled Brake System.

SRS warning light illuminated

X20AF

Guess Toyota Prius Vehicle Speed Malfunction

Recorded when an estimated vehicle speed flag malfunction signal (invalid value) is received from the skid control ECU.

Refer to How to Proceed with Troubleshooting in Electronically Controlled Brake System.

SRS warning light illuminated

X20D0

Zero Point Calibration of Occupant Detection Load Sensor Undone

Recorded when occupant classification zero point calibration is not performed or could not be completed normally.

SRS warning light illuminated

X210B

SRS Airbag ECU IG Voltage Drop

Recorded when the IGR terminal input voltage is continuously less than 8 V for 60 seconds.

CLEAR Toyota Prius Vehicle CONTROL HISTORY

(a) According to the display on the GTS, clear the Vehicle Control History (RoB).

Body Electrical > SRS Airbag > Utility

Toyota Prius Vehicle Control History (RoB)

Passenger Seat Occupant Classification Sensor "A" Signal Bias Level Out of Range / Zero Adjustment Failure (B00C028)

DESCRIPTION

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

DTC Output from

Priority

B00C028

Passenger Seat Occupant Classification Sensor "A" Signal Bias Level Out of Range / Zero Adjustment Failure

Either of following conditions is met:

  • Front occupant classification sensor LH sensed large load
  • Front occupant classification sensor LH malfunction

Front seat adjuster assembly RH (front occupant classification sensor LH)

SRS Airbag

A

NOTICE:

  • After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

    Click here

    HINT:

    When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

    Click here

  • After replacing the front seat adjuster assembly RH, refer to work procedure.

    Click here

PROCEDURE

  1. PERFORM ZERO POINT CALIBRATION

(a) Using the GTS, perform "Occupant Detection Sensor Zero Point Calibration".

HINT:

Click here

NEXT
  1. CLEAR DTC

Pre-procedure1

(a) Turn the ignition switch to ON, and wait for at least 60 seconds.

Procedure1

(b) Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs

Post-procedure1

(c) Turn the ignition switch off.

NEXT
  1. CHECK DTC

Pre-procedure1

(a) Turn the ignition switch to ON, and wait for at least 60 seconds.

Procedure1

(b) Check the DTCs.

Body Electrical > SRS Airbag > Trouble Codes

Result

Proceed to

B00C028 is output

A

B00C028 is not output

B

Post-procedure1

(c) None

B

END (NORMAL AFTER PERFORMING ZERO POINT CALIBRATION)

A
  1. REPLACE FRONT SEAT ADJUSTER ASSEMBLY RH

Pre-procedure1

(a) Turn the ignition switch off.

(b) Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.

Procedure1

(c) Replace the front seat adjuster assembly RH with a new one.

HINT:

Click here

Post-procedure1

(d) Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.

NEXT
  1. PERFORM ZERO POINT CALIBRATION

(a) Using the GTS, perform "Occupant Detection Sensor Zero Point Calibration".

HINT:

Click here

NEXT

END (FRONT SEAT ADJUSTER ASSEMBLY RH WAS DEFECTIVE)

Passenger Seat Occupant Classification Sensor "A" Signal (some circuit quantity, reported via serial data) Invalid (B00C086)

DESCRIPTION

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

DTC Output from

Priority

B00C086

Passenger Seat Occupant Classification Sensor "A" Signal (some circuit quantity, reported via serial data) Invalid

Either of following conditions is met:

  • The airbag ECU assembly detects a line short, short to ground or B in the front occupant classification sensor LH circuit.
  • Front occupant classification sensor LH malfunction
  • Airbag ECU assembly malfunction
  • Harness or connector
  • Front seat adjuster assembly RH (front occupant classification sensor LH)
  • Airbag ECU assembly

SRS Airbag

A

WIRING DIAGRAM

NOTICE:

  • After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

    Click here

    HINT:

    When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

    Click here

  • After replacing the airbag ECU assembly or front seat adjuster assembly RH, refer to work procedure.

    Click here

HINT:

  • If it is difficult to perform troubleshooting (wire harness inspection), remove the front passenger seat installation bolts to see under the seat cushion.
  • In the above case, lift and hold the seat so that it does not fall down. Hold the seat only as necessary because holding the seat for a long period of time may cause seat rail deformation.

PROCEDURE

  1. CHECK DTC

(a) Check the DTCs.

Body Electrical > SRS Airbag > Trouble Codes

Result

Proceed to

B00C086 is output

A

B00C286 is output

B

B00C086 and B00C286 are output

C

B00C086 and B00C286 are not output

D

HINT:

Codes other than DTCs B00C086 and B00C286 may be output at this time, but they are not related to this check.

B

GO TO STEP 5

C

GO TO STEP 8

D

USE SIMULATION METHOD TO CHECK

A
  1. CHECK CONNECTION OF CONNECTORS

Pre-procedure1

(a) Turn the ignition switch off.

(b) Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.

Procedure1

(c) Check that the connectors are properly connected to the airbag ECU assembly and front seat adjuster assembly RH (front occupant classification sensor LH).

OK:

The connectors are properly connected.

Post-procedure1

(d) None

NG

CONNECT CONNECTORS PROPERLY

OK
  1. CHECK CONNECTORS

Pre-procedure1

(a) Disconnect the airbag ECU assembly connector.

*1

Front Seat Adjuster Assembly RH (Front Occupant Classification Sensor LH)

*2

Airbag ECU Assembly

*3

Wire Harness

(b) Disconnect the front seat adjuster assembly RH (front occupant classification sensor LH) connector.

Procedure1

(c) Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.

Post-procedure1

(d) None

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (AIRBAG ECU ASSEMBLY - FRONT SEAT ADJUSTER ASSEMBLY RH)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(R1,a17) Click Connector(R1) Click Connector(a17)

Tester Connection

Condition

Specified Condition

Result

R1-32 (SIG) - a17-2

Always

Below 1 Ω

Ω

*1

Front Seat Adjuster Assembly RH

*2

Airbag ECU Assembly

*3

Wire Harness

*a

Front view of wire harness connector

(to Airbag ECU Assembly)

*b

Front view of wire harness connector

(to Front Seat Adjuster Assembly RH (Front Occupant Classification Sensor LH))

OK

REPLACE FRONT SEAT ADJUSTER ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. CHECK CONNECTION OF CONNECTORS

Pre-procedure1

(a) Turn the ignition switch off.

(b) Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.

Procedure1

(c) Check that the connectors are properly connected to the airbag ECU assembly and front seat adjuster assembly RH (rear occupant classification sensor LH).

OK:

The connectors are properly connected.

Post-procedure1

(d) None

NG

CONNECT CONNECTORS PROPERLY

OK
  1. CHECK CONNECTORS

Pre-procedure1

(a) Disconnect the airbag ECU assembly connector.

*1

Front Seat Adjuster Assembly RH (Rear Occupant Classification Sensor LH)

*2

Airbag ECU Assembly

*3

Wire Harness

(b) Disconnect the front seat adjuster assembly RH (rear occupant classification sensor LH) connector.

Procedure1

(c) Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.

Post-procedure1

(d) None

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (AIRBAG ECU ASSEMBLY - FRONT SEAT ADJUSTER ASSEMBLY RH)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(R1,a18) Click Connector(R1) Click Connector(a18)

Tester Connection

Condition

Specified Condition

Result

R1-32 (SIG) - a18-2

Always

Below 1 Ω

Ω

*1

Front Seat Adjuster Assembly RH

*2

Airbag ECU Assembly

*3

Wire Harness

*a

Front view of wire harness connector

(to Airbag ECU Assembly)

*b

Front view of wire harness connector

(to Front Seat Adjuster Assembly RH (Rear Occupant Classification Sensor LH))

OK

REPLACE FRONT SEAT ADJUSTER ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. CHECK CONNECTION OF CONNECTORS

Pre-procedure1

(a) Turn the ignition switch off.

(b) Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.

Procedure1

(c) Check that the connectors are properly connected to the airbag ECU assembly and front seat adjuster assembly RH.

OK:

The connectors are properly connected.

Post-procedure1

(d) None

NG

CONNECT CONNECTORS PROPERLY

OK
  1. CHECK CONNECTORS

Pre-procedure1

(a) Disconnect the airbag ECU assembly connector.

*1

Front Seat Adjuster Assembly RH

*2

Airbag ECU Assembly

*3

Wire Harness

(b) Disconnect the front seat adjuster assembly RH connector.

Procedure1

(c) Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.

Post-procedure1

(d) None

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (AIRBAG ECU ASSEMBLY - FRONT SEAT ADJUSTER ASSEMBLY RH)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(R1,a17,a18) Click Connector(R1) Click Connector(a17) Click Connector(a18)

Tester Connection

Condition

Specified Condition

Result

R1-32 (SIG) - a17-2

Always

Below 1 Ω

Ω

R1-32 (SIG) - a18-2

Always

Below 1 Ω

Ω

*1

Front Seat Adjuster Assembly RH

*2

Airbag ECU Assembly

*3

Wire Harness

*a

Front view of wire harness connector

(to Airbag ECU Assembly)

*b

Front view of wire harness connector

(to Front Seat Adjuster Assembly RH (Front Occupant Classification Sensor LH))

*c

Front view of wire harness connector

(to Front Seat Adjuster Assembly RH (Rear Occupant Classification Sensor LH))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (AIRBAG ECU ASSEMBLY - FRONT SEAT ADJUSTER ASSEMBLY RH)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(R1,a17,a18) Click Connector(R1) Click Connector(a17) Click Connector(a18)

Tester Connection

Condition

Specified Condition

Result

R1-32 (SIG) - Other terminals and body ground

Always

10 kΩ or higher

kΩ

a17-2 - Other terminals and body ground

Always

10 kΩ or higher

kΩ

a18-2 - Other terminals and body ground

Always

10 kΩ or higher

kΩ

*1

Front Seat Adjuster Assembly RH

*2

Airbag ECU Assembly

*3

Wire Harness

*a

Front view of wire harness connector

(to Airbag ECU Assembly)

*b

Front view of wire harness connector

(to Front Seat Adjuster Assembly RH (Front Occupant Classification Sensor LH))

*c

Front view of wire harness connector

(to Front Seat Adjuster Assembly RH (Rear Occupant Classification Sensor LH))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (AIRBAG ECU ASSEMBLY - FRONT SEAT ADJUSTER ASSEMBLY RH)

Pre-procedure1

(a) Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.

(b) Turn the ignition switch to ON.

Procedure1

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Click Location & Routing(R1,a17,a18) Click Connector(R1) Click Connector(a17) Click Connector(a18)

Tester Connection

Condition

Specified Condition

Result

R1-32 (SIG) - Body ground

Ignition switch ON

Below 1 V

V

a17-2 - Body ground

Ignition switch ON

Below 1 V

V

a18-2 - Body ground

Ignition switch ON

Below 1 V

V

Result:

Proceed to

OK

NG

*1

Front Seat Adjuster Assembly RH

*2

Airbag ECU Assembly

*3

Wire Harness

*a

Front view of wire harness connector

(to Airbag ECU Assembly)

*b

Front view of wire harness connector

(to Front Seat Adjuster Assembly RH (Front Occupant Classification Sensor LH))

*c

Front view of wire harness connector

(to Front Seat Adjuster Assembly RH (Rear Occupant Classification Sensor LH))

Post-procedure1

(d) None

OK

REPLACE AIRBAG ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

Passenger Seat Occupant Classification Sensor "A" Missing Message (B00C087)

DESCRIPTION

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

DTC Output from

Priority

B00C087

Passenger Seat Occupant Classification Sensor "A" Missing Message

Either of following conditions is met:

  • The airbag ECU assembly detects a line open in the front occupant classification sensor LH circuit.
  • Front occupant classification sensor LH malfunction
  • Airbag ECU assembly malfunction
  • Harness or connector
  • Front seat adjuster assembly RH (front occupant classification sensor LH)
  • Airbag ECU assembly

SRS Airbag

A

WIRING DIAGRAM

NOTICE:

  • After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

    Click here

    HINT:

    When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

    Click here

  • After replacing the airbag ECU assembly or front seat adjuster assembly RH, refer to work procedure.

    Click here

HINT:

  • If it is difficult to perform troubleshooting (wire harness inspection), remove the front passenger seat installation bolts to see under the seat cushion.
  • In the above case, lift and hold the seat so that it does not fall down. Hold the seat only as necessary because holding the seat for a long period of time may cause seat rail deformation.

PROCEDURE

  1. CHECK DTC

(a) Check the DTCs.

Body Electrical > SRS Airbag > Trouble Codes

Result

Proceed to

B00C087 is output

A

B00C287 is output

B

B00C087 and B00C287 are output

C

B00C087 and B00C287 are not output

D

HINT:

Codes other than DTCs B00C087 and B00C287 may be output at this time, but they are not related to this check.

B

GO TO STEP 5

C

GO TO STEP 8

D

USE SIMULATION METHOD TO CHECK

A
  1. CHECK CONNECTION OF CONNECTORS

Pre-procedure1

(a) Turn the ignition switch off.

(b) Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.

Procedure1

(c) Check that the connectors are properly connected to the airbag ECU assembly and front seat adjuster assembly RH (front occupant classification sensor LH).

OK:

The connectors are properly connected.

Post-procedure1

(d) None

NG

CONNECT CONNECTORS PROPERLY

OK
  1. CHECK CONNECTORS

Pre-procedure1

(a) Disconnect the airbag ECU assembly connector.

*1

Front Seat Adjuster Assembly RH (Front Occupant Classification Sensor LH)

*2

Airbag ECU Assembly

*3

Wire Harness

(b) Disconnect the front seat adjuster assembly RH (front occupant classification sensor LH) connector.

Procedure1

(c) Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.

Post-procedure1

(d) None

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (AIRBAG ECU ASSEMBLY - FRONT SEAT ADJUSTER ASSEMBLY RH)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(R1,a17) Click Connector(R1) Click Connector(a17)

Tester Connection

Condition

Specified Condition

Result

R1-24 (SVC) - a17-1

Always

Below 1 Ω

Ω

R1-32 (SIG) - a17-2

Always

Below 1 Ω

Ω

R1-31 (SGD) - a17-3

Always

Below 1 Ω

Ω

*1

Front Seat Adjuster Assembly RH

*2

Airbag ECU Assembly

*3

Wire Harness

*a

Front view of wire harness connector

(to Airbag ECU Assembly)

*b

Front view of wire harness connector

(to Front Seat Adjuster Assembly RH (Front Occupant Classification Sensor LH))

OK

REPLACE FRONT SEAT ADJUSTER ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. CHECK CONNECTION OF CONNECTORS

Pre-procedure1

(a) Turn the ignition switch off.

(b) Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.

Procedure1

(c) Check that the connectors are properly connected to the airbag ECU assembly and front seat adjuster assembly RH (rear occupant classification sensor LH).

OK:

The connectors are properly connected.

Post-procedure1

(d) None

NG

CONNECT CONNECTORS PROPERLY

OK
  1. CHECK CONNECTORS

Pre-procedure1

(a) Disconnect the airbag ECU assembly connector.

*1

Front Seat Adjuster Assembly RH (Rear Occupant Classification Sensor LH)

*2

Airbag ECU Assembly

*3

Wire Harness

(b) Disconnect the front seat adjuster assembly RH (rear occupant classification sensor LH) connector.

Procedure1

(c) Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.

Post-procedure1

(d) None

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (AIRBAG ECU ASSEMBLY - FRONT SEAT ADJUSTER ASSEMBLY RH)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(R1,a18) Click Connector(R1) Click Connector(a18)

Tester Connection

Condition

Specified Condition

Result

R1-24 (SVC) - a18-1

Always

Below 1 Ω

Ω

R1-32 (SIG) - a18-2

Always

Below 1 Ω

Ω

R1-31 (SGD) - a18-3

Always

Below 1 Ω

Ω

*1

Front Seat Adjuster Assembly RH

*2

Airbag ECU Assembly

*3

Wire Harness

*a

Front view of wire harness connector

(to Airbag ECU Assembly)

*b

Front view of wire harness connector

(to Front Seat Adjuster Assembly RH (Rear Occupant Classification Sensor LH))

OK

REPLACE FRONT SEAT ADJUSTER ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. CHECK CONNECTION OF CONNECTORS

Pre-procedure1

(a) Turn the ignition switch off.

(b) Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.

Procedure1

(c) Check that the connectors are properly connected to the airbag ECU assembly and front seat adjuster assembly RH.

OK:

The connectors are properly connected.

Post-procedure1

(d) None

NG

CONNECT CONNECTORS PROPERLY

OK
  1. CHECK CONNECTORS

Pre-procedure1

(a) Disconnect the airbag ECU assembly connector.

*1

Front Seat Adjuster Assembly RH

*2

Airbag ECU Assembly

*3

Wire Harness

(b) Disconnect the front seat adjuster assembly RH connector.

Procedure1

(c) Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.

Post-procedure1

(d) None

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (AIRBAG ECU ASSEMBLY - FRONT SEAT ADJUSTER ASSEMBLY RH)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(R1,a17,a18) Click Connector(R1) Click Connector(a17) Click Connector(a18)

Tester Connection

Condition

Specified Condition

Result

R1-24 (SVC) - a17-1

Always

Below 1 Ω

Ω

R1-24 (SVC) - a18-1

Always

Below 1 Ω

Ω

R1-32 (SIG) - a17-2

Always

Below 1 Ω

Ω

R1-32 (SIG) - a18-2

Always

Below 1 Ω

Ω

R1-31 (SGD) - a17-3

Always

Below 1 Ω

Ω

R1-31 (SGD) - a18-3

Always

Below 1 Ω

Ω

*1

Front Seat Adjuster Assembly RH

*2

Airbag ECU Assembly

*3

Wire Harness

*a

Front view of wire harness connector

(to Airbag ECU Assembly)

*b

Front view of wire harness connector

(to Front Seat Adjuster Assembly RH (Front Occupant Classification Sensor LH))

*c

Front view of wire harness connector

(to Front Seat Adjuster Assembly RH (Rear Occupant Classification Sensor LH))

OK

REPLACE AIRBAG ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

Passenger Seat Occupant Classification Sensor "A" Component Internal Failure (B00C096)

DESCRIPTION

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

DTC Output from

Priority

B00C096

Passenger Seat Occupant Classification Sensor "A" Component Internal Failure

Front occupant classification sensor LH malfunction

Front seat adjuster assembly RH (front occupant classification sensor LH)

SRS Airbag

A

NOTICE:

After replacing the front seat adjuster assembly RH, refer to work procedure.

Click here

PROCEDURE

  1. CLEAR DTC

Pre-procedure1

(a) Turn the ignition switch to ON, and wait for at least 60 seconds.

Procedure1

(b) Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs

Post-procedure1

(c) Turn the ignition switch off.

NEXT
  1. CHECK DTC

Pre-procedure1

(a) Turn the ignition switch to ON, and wait for at least 60 seconds.

Procedure1

(b) Check the DTCs.

Body Electrical > SRS Airbag > Trouble Codes

Result

Proceed to

B00C096 is output

A

B00C096 is not output

B

Post-procedure1

(c) None

A

REPLACE FRONT SEAT ADJUSTER ASSEMBLY RH

B

USE SIMULATION METHOD TO CHECK

Load Sensor for Occupant Detection System Circuit Short to Battery (B179312)

DESCRIPTION

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

DTC Output from

Priority

B179312

Load Sensor for Occupant Detection System Circuit Short to Battery

When the detections voltage higher than specified value before supplying power to the sensor.

  • Harness or connector
  • Airbag ECU assembly

SRS Airbag

A

WIRING DIAGRAM

NOTICE:

  • After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

    Click here

    HINT:

    When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

    Click here

  • After replacing the airbag ECU assembly, refer to work procedure.

    Click here

HINT:

  • If it is difficult to perform troubleshooting (wire harness inspection), remove the front passenger seat installation bolts to see under the seat cushion.
  • In the above case, lift and hold the seat so that it does not fall down. Hold the seat only as necessary because holding the seat for a long period of time may cause seat rail deformation.

PROCEDURE

  1. CHECK CONNECTION OF CONNECTORS

Pre-procedure1

(a) Turn the ignition switch off.

(b) Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.

Procedure1

(c) Check that the connectors are properly connected to the airbag ECU assembly and front seat adjuster assembly RH.

OK:

The connectors are properly connected.

Post-procedure1

(d) None

NG

CONNECT CONNECTORS PROPERLY

OK
  1. CHECK CONNECTORS

Pre-procedure1

(a) Disconnect the airbag ECU assembly connector.

*1

Front Seat Adjuster Assembly RH

*2

Airbag ECU Assembly

*3

Wire Harness

(b) Disconnect the front seat adjuster assembly RH connector.

Procedure1

(c) Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.

Post-procedure1

(d) None

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (AIRBAG ECU ASSEMBLY - FRONT SEAT ADJUSTER ASSEMBLY RH)

Pre-procedure1

(a) Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.

(b) Turn the ignition switch to ON.

Procedure1

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Click Location & Routing(R1,a17,a18) Click Connector(R1) Click Connector(a17) Click Connector(a18)

Tester Connection

Condition

Specified Condition

Result

R1-24 (SVC) - Body ground

Ignition switch ON

Below 1 V

V

a17-1 - Body ground

Ignition switch ON

Below 1 V

V

a18-1 - Body ground

Ignition switch ON

Below 1 V

V

Result:

Proceed to

OK

NG

*1

Front Seat Adjuster Assembly RH

*2

Airbag ECU Assembly

*3

Wire Harness

*a

Front view of wire harness connector

(to Airbag ECU Assembly)

*b

Front view of wire harness connector

(to Front Seat Adjuster Assembly RH (Front Occupant Classification Sensor LH))

*c

Front view of wire harness connector

(to Front Seat Adjuster Assembly RH (Rear Occupant Classification Sensor LH))

Post-procedure1

(d) None

OK

REPLACE AIRBAG ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

Load Sensor for Occupant Detection System Circuit Voltage Below Threshold (B179316)

DESCRIPTION

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

DTC Output from

Priority

B179316

Load Sensor for Occupant Detection System Circuit Voltage Below Threshold

When the detections voltage value below specified value before supplying power to the sensor.

  • Harness or connector
  • Front seat adjuster assembly RH
  • Airbag ECU assembly

SRS Airbag

A

WIRING DIAGRAM

NOTICE:

  • After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

    Click here

    HINT:

    When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

    Click here

  • After replacing the airbag ECU assembly or front seat adjuster assembly RH, refer to work procedure.

    Click here

  • Inspect the fuses for circuits related to this system before performing the following procedure.

HINT:

  • If it is difficult to perform troubleshooting (wire harness inspection), remove the front passenger seat installation bolts to see under the seat cushion.
  • In the above case, lift and hold the seat so that it does not fall down. Hold the seat only as necessary because holding the seat for a long period of time may cause seat rail deformation.

PROCEDURE

  1. CHECK CONNECTION OF CONNECTORS

Pre-procedure1

(a) Turn the ignition switch off.

(b) Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.

Procedure1

(c) Check that the connectors are properly connected to the airbag ECU assembly and front seat adjuster assembly RH.

OK:

The connectors are properly connected.

Post-procedure1

(d) None

NG

CONNECT CONNECTORS PROPERLY

OK
  1. CHECK CONNECTORS

Pre-procedure1

(a) Disconnect the airbag ECU assembly connector.

*1

Front Seat Adjuster Assembly RH

*2

Airbag ECU Assembly

*3

Wire Harness

(b) Disconnect the front seat adjuster assembly RH connector.

Procedure1

(c) Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.

Post-procedure1

(d) None

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (AIRBAG ECU ASSEMBLY - AUXILIARY BATTERY)

Pre-procedure1

(a) Disconnect the airbag ECU assembly connector.

(b) Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.

(c) Turn the ignition switch to ON.

(d) Operate all components of the electrical systems (defogger, wipers, headlights, heater blower, etc.).

Procedure1

(e) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Click Location & Routing(K1) Click Connector(K1)

Tester Connection

Condition

Specified Condition

Result

K1-36 (IGR) - Body ground

Ignition switch ON

8 to 16 V

V

Result:

Proceed to

OK

NG

*a

Front view of wire harness connector

(to Airbag ECU Assembly)

Post-procedure1

(f) Turn the ignition switch off.

(g) Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (AIRBAG ECU ASSEMBLY - FRONT SEAT ADJUSTER ASSEMBLY RH)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(R1,a17,a18) Click Connector(R1) Click Connector(a17) Click Connector(a18)

Tester Connection

Condition

Specified Condition

Result

R1-24 (SVC) - Other terminals and body ground

Always

10 kΩ or higher

kΩ

a17-1 - Other terminals and body ground

Always

10 kΩ or higher

kΩ

a18-1 - Other terminals and body ground

Always

10 kΩ or higher

kΩ

*1

Front Seat Adjuster Assembly RH

*2

Airbag ECU Assembly

*3

Wire Harness

*a

Front view of wire harness connector

(to Airbag ECU Assembly)

*b

Front view of wire harness connector

(to Front Seat Adjuster Assembly RH (Front Occupant Classification Sensor LH))

*c

Front view of wire harness connector

(to Front Seat Adjuster Assembly RH (Rear Occupant Classification Sensor LH))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK AIRBAG ECU ASSEMBLY

Pre-procedure1

(a) Connect the connector to the airbag ECU assembly.

(b) Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.

(c) Turn the ignition switch to ON.

Procedure1

(d) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Click Location & Routing(a17,a18) Click Connector(a17) Click Connector(a18)

Tester Connection

Condition

Specified Condition

Result

a17-1 - Body ground

Ignition switch ON

6.2 V or higher

V

a18-1 - Body ground

Ignition switch ON

6.2 V or higher

V

Result:

Proceed to

OK

NG

*1

Front Seat Adjuster Assembly RH

*2

Airbag ECU Assembly

*3

Wire Harness

*a

Front view of wire harness connector

(to Front Seat Adjuster Assembly RH (Front Occupant Classification Sensor LH))

*b

Front view of wire harness connector

(to Front Seat Adjuster Assembly RH (Rear Occupant Classification Sensor LH))

Post-procedure1

(e) None

OK

REPLACE FRONT SEAT ADJUSTER ASSEMBLY RH

NG

REPLACE AIRBAG ECU ASSEMBLY

Trouble in Passenger Airbag ON/OFF Indicator

DESCRIPTION

The occupant classification system detects the front passenger seat condition. It then displays the instrument panel passenger airbag assembly condition (activated/not activated) using the passenger airbag ON/OFF indicator.

HINT:

Approximately 6 seconds after the ignition switch is turned to ON, the passenger airbag ON/OFF indicator will indicate ON/OFF depending on the following conditions.

Indicator Operation

Front Passenger Seat Condition

Passenger Airbag ON/OFF Indicator

SRS Warning Light

ON Indicator

OFF Indicator

Vacant

OFF

ON

OFF

Adult*1 is seated

ON

OFF

OFF

Child*2 is seated

ON or OFF*2

OFF or ON*2

OFF

Child restraint system is installed

OFF

ON

OFF

Occupant classification system failure

OFF

ON

ON

  • *1: The system judges a person of average adult weight or more as an adult. If a smaller adult sits in the front passenger seat, the system may not recognize them as an adult depending on their physique and posture.
  • *2: The system may not recognize a child or a child in a child restraint system as a child depending on factors such as the positioning of the child restraint system or the child's physique or posture.

NOTICE:

  • After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

    Click here

    HINT:

    When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

    Click here

  • After replacing the airbag ECU assembly, refer to work procedure.

    Click here

PROCEDURE

  1. CHECK SRS WARNING LIGHT

(a) Turn the ignition switch to ON, and check the SRS warning light condition.

OK:

After the primary check period, the SRS warning light goes off.

HINT:

The primary check is performed for approximately 6 seconds after the ignition switch is turned to ON.

NG

GO TO AIRBAG SYSTEM

OK
  1. PERFORM ZERO POINT CALIBRATION

(a) Using the GTS, perform "Occupant Detection Sensor Zero Point Calibration".

Click here

NEXT
  1. CHECK PASSENGER AIRBAG ON/OFF INDICATOR

(a) Check the passenger airbag ON/OFF indicator.

Click here

OK:

Passenger airbag ON/OFF indicator operation normally.

OK

END (NORMAL AFTER PERFORMING ZERO POINT CALIBRATION)

NG
  1. RETIGHTEN FRONT SEAT ASSEMBLY RH BOLT

(a) Loosen the 4 installation bolts of the front seat assembly RH.

(b) Tighten the 4 installation bolts of the front seat assembly RH to the specified torque.

Click here

NEXT
  1. PERFORM ZERO POINT CALIBRATION

(a) Using the GTS, perform "Occupant Detection Sensor Zero Point Calibration".

Click here

NEXT
  1. CHECK PASSENGER AIRBAG ON/OFF INDICATOR

(a) Check the passenger airbag ON/OFF indicator.

Click here

OK:

Passenger airbag ON/OFF indicator operation normally.

OK

END (THE 4 INSTALLATION BOLTS WAS LOOSEN)

NG
  1. READ VALUE USING GTS

(a) Read the Data List according to the display on the GTS.

Body Electrical > SRS Airbag > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Judgment Result for Occupant Detection System (Buckle Switch of Passenger Seat)

Front passenger side buckle switch

Unknown, Buckle, Unbuckle or Malfunction

Buckle: Front passenger seat belt is fastened

Unbuckle: Front passenger seat belt is not fastened

Malfunction: Front passenger seat belt is malfunctioning

-

Body Electrical > SRS Airbag > Data List

Judgment Result for Occupant Detection System (Buckle Switch of Passenger Seat)

OK:

The GTS display changes correctly in accordance with the operation of the front passenger side buckle switch.

NG

GO TO STEP 11

OK
  1. CHECK CONNECTORS

(a) Turn the ignition switch off.

*1

Front Seat Adjuster Assembly RH

*2

Airbag ECU Assembly

*3

Wire Harness

(b) Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.

(c) Disconnect the airbag ECU assembly connector.

(d) Disconnect the front seat adjuster assembly RH connector.

(e) Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. REPLACE AIRBAG ECU ASSEMBLY

(a) Connect the front seat adjuster assembly RH connector.

(b) Replace the airbag ECU assembly with a new one.

Click here

(c) Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.

NEXT
  1. PERFORM ZERO POINT CALIBRATION

(a) Using the GTS, perform "Occupant Detection Sensor Zero Point Calibration".

Click here

NEXT

END (AIRBAG ECU ASSEMBLY WAS DEFECTIVE)

  1. CHECK CONNECTORS

(a) Turn the ignition switch off.

*1

Front Seat Inner Belt Assembly RH

*2

Airbag ECU Assembly

*3

Wire Harness

(b) Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.

(c) Disconnect the airbag ECU assembly connector.

(d) Disconnect the front seat inner belt assembly RH connector.

(e) Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. REPLACE FRONT SEAT INNER BELT ASSEMBLY RH

(a) Connect the airbag ECU assembly connector.

(b) Replace the front seat inner belt assembly RH with a new one.

Click here

(c) Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.

NEXT
  1. PERFORM ZERO POINT CALIBRATION

(a) Using the GTS, perform "Occupant Detection Sensor Zero Point Calibration".

Click here

NEXT

END (FRONT SEAT INNER BELT ASSEMBLY RH WAS DEFECTIVE)

LIN Communication Circuit

DESCRIPTION

Error Code

Detection Item

Detection Condition

Trouble Area

17

FI LIN Communication Lost

When a communication malfunction with the load sensor is detected

  • Harness or connector
  • Front seat adjuster assembly RH (front occupant classification sensor LH)
  • Airbag ECU assembly

18

RI LIN Communication Lost

When a communication malfunction with the load sensor is detected

  • Harness or connector
  • Front seat adjuster assembly RH (rear occupant classification sensor LH)
  • Airbag ECU assembly

WIRING DIAGRAM

NOTICE:

  • After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

    Click here

    HINT:

    When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

    Click here

  • After replacing the airbag ECU assembly or front seat adjuster assembly RH, refer to work procedure.

    Click here

HINT:

  • If it is difficult to perform troubleshooting (wire harness inspection), remove the front passenger seat installation bolts to see under the seat cushion.
  • In the above case, lift and hold the seat so that it does not fall down. Hold the seat only as necessary because holding the seat for a long period of time may cause seat rail deformation.

PROCEDURE

  1. CHECK ERROR CODE

(a) Check the Error Code.

Result

Proceed to

Error code 17 is output

A

Error code 18 is output

B

Error code 17 and 18 are output

C

B

GO TO STEP 7

C

GO TO STEP 12

A
  1. CHECK CONNECTION OF CONNECTORS

(a) Turn the ignition switch off.

(b) Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.

(c) Check that the connectors are properly connected to the airbag ECU assembly and front seat adjuster assembly RH (front occupant classification sensor LH).

OK:

The connectors are properly connected.

NG

CONNECT CONNECTORS PROPERLY

OK
  1. CHECK CONNECTORS

(a) Disconnect the airbag ECU assembly connector.

*1

Front Seat Adjuster Assembly RH (Front Occupant Classification Sensor LH)

*2

Airbag ECU Assembly

*3

Wire Harness

(b) Disconnect the front seat adjuster assembly RH (front occupant classification sensor LH) connector.

(c) Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (AIRBAG ECU ASSEMBLY - FRONT SEAT ADJUSTER ASSEMBLY RH)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(R1,a17) Click Connector(R1) Click Connector(a17)

Tester Connection

Condition

Specified Condition

R1-24 (SVC) - a17-1

Always

Below 1 Ω

R1-32 (SIG) - a17-2

Always

Below 1 Ω

R1-31 (SGD) - a17-3

Always

Below 1 Ω

*1

Front Seat Adjuster Assembly RH

*2

Airbag ECU Assembly

*3

Wire Harness

*a

Front view of wire harness connector

(to Airbag ECU Assembly)

*b

Front view of wire harness connector

(to Front Seat Adjuster Assembly RH (Front Occupant Classification Sensor LH))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. REPLACE FRONT SEAT ADJUSTER ASSEMBLY RH

(a) Connect the airbag ECU assembly connector.

(b) Replace the front seat adjuster assembly RH with a new one.

Click here

NEXT
  1. PERFORM ZERO POINT CALIBRATION

(a) Using the GTS, perform "Occupant Detection Sensor Zero Point Calibration".

Click here

NEXT

END

  1. CHECK CONNECTION OF CONNECTORS

(a) Turn the ignition switch off.

(b) Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.

(c) Check that the connectors are properly connected to the airbag ECU assembly and front seat adjuster assembly RH (rear occupant classification sensor LH).

OK:

The connectors are properly connected.

NG

CONNECT CONNECTORS PROPERLY

OK
  1. CHECK CONNECTORS

(a) Disconnect the airbag ECU assembly connector.

*1

Front Seat Adjuster Assembly RH (Rear Occupant Classification Sensor LH)

*2

Airbag ECU Assembly

*3

Wire Harness

(b) Disconnect the front seat adjuster assembly RH (rear occupant classification sensor LH) connector.

(c) Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (AIRBAG ECU ASSEMBLY - FRONT SEAT ADJUSTER ASSEMBLY RH)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(R1,a18) Click Connector(R1) Click Connector(a18)

Tester Connection

Condition

Specified Condition

R1-24 (SVC) - a18-1

Always

Below 1 Ω

R1-32 (SIG) - a18-2

Always

Below 1 Ω

R1-31 (SGD) - a18-3

Always

Below 1 Ω

*1

Front Seat Adjuster Assembly RH

*2

Airbag ECU Assembly

*3

Wire Harness

*a

Front view of wire harness connector

(to Airbag ECU Assembly)

*b

Front view of wire harness connector

(to Front Seat Adjuster Assembly RH (Rear Occupant Classification Sensor LH))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. REPLACE FRONT SEAT ADJUSTER ASSEMBLY RH

(a) Connect the airbag ECU assembly connector.

(b) Replace the front seat adjuster assembly RH with a new one.

Click here

NEXT
  1. PERFORM ZERO POINT CALIBRATION

(a) Using the GTS, perform "Occupant Detection Sensor Zero Point Calibration".

Click here

NEXT

END

  1. CHECK CONNECTION OF CONNECTORS

(a) Turn the ignition switch off.

(b) Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.

(c) Check that the connectors are properly connected to the airbag ECU assembly and front seat adjuster assembly RH.

OK:

The connectors are properly connected.

NG

CONNECT CONNECTORS PROPERLY

OK
  1. CHECK CONNECTORS

(a) Disconnect the airbag ECU assembly connector.

*1

Front Seat Adjuster Assembly RH

*2

Airbag ECU Assembly

*3

Wire Harness

(b) Disconnect the front seat adjuster assembly RH connector.

(c) Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (AIRBAG ECU ASSEMBLY - FRONT SEAT ADJUSTER ASSEMBLY RH)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(R1,a17,a18) Click Connector(R1) Click Connector(a17) Click Connector(a18)

Tester Connection

Condition

Specified Condition

R1-24 (SVC) - a17-1

Always

Below 1 Ω

R1-24 (SVC) - a18-1

Always

Below 1 Ω

R1-32 (SIG) - a17-2

Always

Below 1 Ω

R1-32 (SIG) - a18-2

Always

Below 1 Ω

R1-31 (SGD) - a17-3

Always

Below 1 Ω

R1-31 (SGD) - a18-3

Always

Below 1 Ω

*1

Front Seat Adjuster Assembly RH

*2

Airbag ECU Assembly

*3

Wire Harness

*a

Front view of wire harness connector

(to Airbag ECU Assembly)

*b

Front view of wire harness connector

(to Front Seat Adjuster Assembly RH (Front Occupant Classification Sensor LH))

*c

Front view of wire harness connector

(to Front Seat Adjuster Assembly RH (Rear Occupant Classification Sensor LH))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (AIRBAG ECU ASSEMBLY - FRONT SEAT ADJUSTER ASSEMBLY RH)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(R1,a17,a18) Click Connector(R1) Click Connector(a17) Click Connector(a18)

Tester Connection

Condition

Specified Condition

R1-32 (SIG) - Other terminals and body ground

Always

10 kΩ or higher

a17-2 - Other terminals and body ground

Always

10 kΩ or higher

a18-2 - Other terminals and body ground

Always

10 kΩ or higher

*1

Front Seat Adjuster Assembly RH

*2

Airbag ECU Assembly

*3

Wire Harness

*a

Front view of wire harness connector

(to Airbag ECU Assembly)

*b

Front view of wire harness connector

(to Front Seat Adjuster Assembly RH (Front Occupant Classification Sensor LH))

*c

Front view of wire harness connector

(to Front Seat Adjuster Assembly RH (Rear Occupant Classification Sensor LH))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (AIRBAG ECU ASSEMBLY - FRONT SEAT ADJUSTER ASSEMBLY RH)

(a) Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.

*1

Front Seat Adjuster Assembly RH

*2

Airbag ECU Assembly

*3

Wire Harness

*a

Front view of wire harness connector

(to Airbag ECU Assembly)

*b

Front view of wire harness connector

(to Front Seat Adjuster Assembly RH (Front Occupant Classification Sensor LH))

*c

Front view of wire harness connector

(to Front Seat Adjuster Assembly RH (Rear Occupant Classification Sensor LH))

(b) Turn the ignition switch to ON.

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Click Location & Routing(R1,a17,a18) Click Connector(R1) Click Connector(a17) Click Connector(a18)

Tester Connection

Condition

Specified Condition

R1-32 (SIG) - Body ground

Ignition switch ON

Below 1 V

a17-2 - Body ground

Ignition switch ON

Below 1 V

a18-2 - Body ground

Ignition switch ON

Below 1 V

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. REPLACE AIRBAG ECU ASSEMBLY

(a) Connect the front seat adjuster assembly RH connector.

(b) Replace the airbag ECU assembly with a new one.

Click here

NEXT
  1. PERFORM ZERO POINT CALIBRATION

(a) Using the GTS, perform "Occupant Detection Sensor Zero Point Calibration".

Click here

NEXT

END