Engine
- On-vehicle Inspection
On-vehicle Inspection
ON-VEHICLE INSPECTION
CAUTION:
To prevent injury due to contact with an operating cooling fan, keep your hands and clothing away from the cooling fans when working in the engine compartment with the engine running or the ignition switch ON.

PROCEDURE
1. INSPECT COOLANT (for Engine)
HINT:
Click here ![]()
2. INSPECT ENGINE OIL
HINT:
Click here ![]()
3. CHECK AUXILIARY BATTERY
HINT:
Click here ![]()
4. INSPECT SPARK PLUG
HINT:
Click here ![]()
5. INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
HINT:
Click here ![]()
6. INSPECT VALVE LASH ADJUSTER ASSEMBLY NOISE
(a) Put the engine in inspection mode.
Powertrain > Hybrid Control > UtilityInspection Mode
(b) Rev up the engine several times. Check that the engine does not emit unusual noises.
(c) If unusual noises occur, warm up the engine and idle it for 30 minutes or more, then perform the inspection.
HINT:
If any defects or problems are found during the inspection, perform valve lash adjuster assembly inspection.
Click here ![]()
7. INSPECT IGNITION TIMING
NOTICE:
- Check the ignition timing with the cooling fans off.
- Turn off all electrical systems and the A/C.
- When checking the ignition timing, the transaxle should be in park.
Pre-procedure1
(a) Put the engine in inspection mode.
Powertrain > Hybrid Control > UtilityInspection Mode
(b) Warm up and stop the engine.
(c) Put the engine in inspection mode.
Powertrain > Hybrid Control > UtilityInspection Mode
Procedure1
(d) Monitor Ignition Timing Cylinder #1 of the Data List.
Powertrain > Engine > Data ListIgnition Timing Cylinder #1
Standard Ignition Timing:
8 to 24° BTDC at idle
Procedure2
(e) Check that the ignition timing advances immediately when the engine speed is increased.
Procedure3
(f) Monitor Ignition Timing Cylinder #1 of the Data List.
Powertrain > Engine > Active TestActivate the TC Terminal
Ignition Timing Cylinder #1
Standard Ignition Timing:
8 to 12° BTDC at idle
Post-procedure1
(g) None
8. INSPECT ENGINE IDLE SPEED
NOTICE:
- Check the engine idle speed with the cooling fans off.
- Turn off all electrical systems and the A/C.
- When checking the engine idle speed, the transaxle should be in park.
Pre-procedure1
(a) Put the engine in Inspection Mode (Maintenance Mode).
Powertrain > Hybrid Control > UtilityInspection Mode
(b) Warm up and stop the engine.
(c) Put the engine in Inspection Mode (Maintenance Mode).
Powertrain > Hybrid Control > UtilityInspection Mode
Procedure1
(d) Read the value displayed on the GTS.
Powertrain > Engine > Data ListEngine Speed
Standard Idle Speed:
950 to 1050 rpm
Post-procedure1
(e) None
9. INSPECT COMPRESSION
NOTICE:
Keep the spark plug holes free of foreign matter when measuring the compression pressure.
Pre-procedure1
(a) Put the engine in Inspection Mode (Maintenance Mode).
Powertrain > Hybrid Control > UtilityInspection Mode
(b) Warm up and stop the engine.
(c) Check for DTCs.
Powertrain > Engine > Trouble Codes(d) Remove the 4 spark plugs.
NOTICE:
DTCs will be stored if the inspection is performed with the ignition coil assembly connectors disconnected. Make sure that the ignition coil assembly connectors are connected during the inspection.
HINT:
Click here ![]()
(e) Remove the air cleaner cap sub-assembly.
HINT:
Click here ![]()
(f) Remove the air cleaner hose assembly.
HINT:
Click here ![]()
(g) w/ Stud Bolt: (1) Remove the 2 bolts, 2 nuts and separate the throttle body assembly from the intake manifold. |
|
(h) w/o Stud Bolt:
(1) Remove the 4 bolts and separate the throttle body assembly from the intake manifold.
Procedure1
(i) Check the cylinder compression pressure.
(1) Insert a compression gauge into the spark plug hole. |
![]() |
(2) Depress and hold the brake pedal, and turn the ignition switch to ON (READY). Then check the compression pressure.
Powertrain > Hybrid Control > Active TestCompression Test
Standard Compression Pressure:
Item | Minimum Compression Pressure | Specified Condition | Result |
|---|---|---|---|
Cylinder 1 |
617 kPa 6.3 kgf/cm2 89.5 psi |
813 kPa 8.3 kgf/cm2 118 psi |
kPa kgf/cm2 psi |
Cylinder 2 |
617 kPa 6.3 kgf/cm2 89.5 psi |
813 kPa 8.3 kgf/cm2 118 psi |
kPa kgf/cm2 psi |
Cylinder 3 |
617 kPa 6.3 kgf/cm2 89.5 psi |
813 kPa 8.3 kgf/cm2 118 psi |
kPa kgf/cm2 psi |
Cylinder 4 |
617 kPa 6.3 kgf/cm2 89.5 psi |
813 kPa 8.3 kgf/cm2 118 psi |
kPa kgf/cm2 psi |
Pressure Difference between Each Cylinder |
- |
100 kPa or less 1.0 kgf/cm2 or less 15 psi or less |
kPa kgf/cm2 psi |
NOTICE:
- Inspect all cylinders in the same way.
- Measure the compression pressure as quickly as possible.
- Noise may be emitted from the hybrid Toyota Prius vehicle transaxle assembly. However, this is not a malfunction.
(3) If the cylinder compression pressure is low, pour a small amount of engine oil into the cylinder through the spark plug hole and inspect it again.
HINT:
- If adding oil increases the compression pressure, the piston rings and/or cylinder bore may be worn or damaged.
- If the compression pressure stays low, a valve may be stuck or seated improperly, or there may be leaks in the cylinder head gasket.
Post-procedure1
(j) w/ Stud Bolt:
(1) Install a new throttle body gasket and the throttle body assembly to the intake manifold with the 2 bolts and 2 nuts.
Torque:
10 N·m {102 kgf·cm, 7 ft·lbf}
NOTICE:
If the throttle body assembly has been struck or dropped, replace it.
(k) w/o Stud Bolt:
(1) Install a new throttle body gasket and the throttle body assembly to the intake manifold with the 4 bolts.
Torque:
10 N·m {102 kgf·cm, 7 ft·lbf}
NOTICE:
If the throttle body assembly has been struck or dropped, replace it.
(l) Install the air cleaner hose assembly.
HINT:
Click here ![]()
(m) Install the air cleaner cap sub-assembly.
HINT:
Click here ![]()
(n) Install the 4 spark plugs.
HINT:
Click here ![]()
(o) Clear the DTCs.
Powertrain > Engine > Trouble CodesNOTICE:
After performing the inspection, clear the DTCs and confirm that DTCs are not stored again or that the normal system code is output if using a check wire.
10. INSPECT CO/HC
HINT:
This check determines whether or not the idle CO/HC complies with regulations.
Pre-procedure1
(a) Put the engine in Inspection Mode (Maintenance Mode).
Powertrain > Hybrid Control > UtilityInspection Mode
(b) Run the engine at 2500 rpm for approximately 180 seconds.
(c) Insert a CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe during idle.
Procedure1
(d) Immediately check the CO/HC concentration at idle and then at an engine speed of 2500 rpm.
HINT:
- When performing a 2 mode test (with the engine idling/running at 2500 rpm), the measurement procedures are determined by applicable local regulations.
- If the CO/HC concentration does not comply with the regulations, perform troubleshooting in the order given below.
(1) Check for DTCs.
Powertrain > Engine > Trouble Codes(2) See the following table for possible causes, then inspect the applicable parts and repair them if necessary.
CO | HC | Problem | Cause |
|---|---|---|---|
Normal |
High |
Rough idle |
|
Low |
High |
Rough idle (Fluctuating HC reading) |
|
High |
High |
Rough idle (Black smoke from exhaust) |
|
Post-procedure1
(e) None

