Wireless Door Lock Control System

In this manual: Wireless Door Lock Control System
How To Troubleshoot Ecu Controlled Systems — 1How To Use This Manual — 1Identification Information — 1Repair Instruction — 1Terms — 12zr-fxe Air Cleaner Filter Element — 12zr-fxe Auxiliary Battery — 12zr-fxe Coolant (for Engine Coolant) — 12zr-fxe Oil And Oil Filter — 12zr-fxe Spark Plug — 1Air Conditioning Filter — 1Battery Cooling Filter — 1Brake Fluid — 1Coolant (for Inverter) — 1Front Brake Flexible Hose — 1Front Disc Brake Pad — 1Front Lower Ball Joint — 1Front Wheel Alignment — 1Front Wiper Rubber — 1General Maintenance — 1M20a-fxs Air Cleaner Filter Element — 1M20a-fxs Auxiliary Battery — 1M20a-fxs Coolant (for Engine Coolant) — 1M20a-fxs Oil And Oil Filter — 1M20a-fxs Spark Plug — 1Pa10/pb10/pb12 Hybrid Transaxle Fluid — 1Q810 Hybrid Transaxle Fluid — 1Rear Brake Flexible Hose — 1Rear Disc Brake Pad — 1Rear Wheel Alignment — 1Steering Column — 1Tire And Wheel — 1Transmitter Battery — 1When Disconnecting Or Reconnecting Battery Terminal — 1When Replacing Or Removing/installing Parts — 1Automatic High Beam Main Switch — 1Automatic High Beam System — 1Driver Monitor Camera — 1Driver Monitor Camera System — 1Driver Monitor Ecu — 1Front Camera — 1Front Camera System — 1Front Radar Sensor System — 1Front Side Radar Sensor — 1Front Side Radar Sensor System — 1Millimeter Wave Radar Sensor — 1Utility — 1Advanced Park — 1Advanced Park Main Switch — 1Amplifier Antenna — 1Audio And Visual System — 1Front Door Speaker — 1Instrument Panel Speaker — 1Microphone — 1Noise Filter — 1Pillar Speaker — 1Radio Antenna Cord (for Back Door) — 1Radio Antenna Cord (for Instrument Panel) — 1Radio Antenna Cord (for Roof) — 1Radio Receiver — 1Rear Door Speaker — 1Roof Antenna — 1Stereo Component Amplifier — 1Stereo Jack Adapter Assembly — 1Window Glass Antenna Wire — 1Back-up Battery — 1Dcm(telematics Transceiver) — 1Manual(sos)switch — 1Safety Connect System — 1Telephone And Gps Antenna (for Front Side) — 1Telephone And Gps Antenna (for Roof Side) — 1Telephone And Gps Antenna Cords — 1Garage Door Opener System (for Digital Inner Mirror) — 1Garage Door Opener System (for Ec Inner Mirror) — 1Blind Spot Monitor Sensor — 1Blind Spot Monitor System — 1Clearance Warning Ecu — 1Intuitive Parking Assist System — 1Panoramic View Monitor Switch — 1Panoramic View Monitor System — 1Parking Assist Ecu — 1Parking Assist Light — 1Parking Assist Monitor System — 1Parking Support Brake System — 1Rear View Monitor System — 1Television Camera (for Front) — 1Television Camera (for Rear) — 1Television Camera (for Side) — 1Ultrasonic Sensor (for Front) — 1Ultrasonic Sensor (for Rear) — 1Brake Actuator — 1Brake Pedal Stroke Sensor — 1Electronically Controlled Brake System — 1Front Speed Sensor — 1Rear Speed Sensor (for Awd) — 1Steering Angle Sensor — 1Brake Booster — 1Brake Fluid — 1Brake Line — 1Brake Pedal — 1Brake System — 1Electric Parking Brake Actuator — 1Electric Parking Brake Switch — 1Electric Parking Brake System — 1Forced Release — 1Front Axle Hub — 1Front Axle Hub Bolt — 1Rear Axle Carrier (for 2wd) — 1Rear Axle Carrier (for Awd) — 1Rear Axle Hub (for 2wd) — 1Rear Axle Hub (for Awd) — 1Rear Axle Hub Bolt — 1Steering Knuckle — 1Drive Shaft System — 1Front Drive Shaft Assembly — 1Rear Drive Shaft Assembly — 1Combination Switch — 1Electronic Shift Lever System — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Oil Seal — 1Hybrid Transaxle System — 1Input Shaft Oil Seal — 1Motor Cable — 1Pa10 Hybrid Vehicle Transaxle — 1Pa10 Manual Parking Lock Release — 1Pa10 Oil Cooler — 1Pb10/pb12 Hybrid Vehicle Transaxle — 1Pb10/pb12 Manual Parking Lock Release — 1Pb10/pb12 Oil Cooler — 1Shift Control Actuator — 1Shift Lever — 1Shift Lever Knob — 1Differential Side Gear Shaft — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Side Gear Oil Seal — 1Motor Cable — 1Rear Traction Motor — 1Coolant (for Engine) — 1Cooling Fan Motor — 1Cooling Fan System — 1Radiator — 1Relay — 1Thermostat — 1Water Pump — 1Canister — 1Egr Cooler — 1Egr Valve — 1Emission Control System — 1Fuel Tank Cap — 1Pcv Valve — 1Purge Valve — 1Vacuum Sensor — 1Air Fuel Ratio Sensor — 1Camshaft Oil Control Valve — 1Camshaft Position Sensor — 1Crankshaft Position Sensor — 1Ecm — 1Engine Coolant Temperature Sensor — 1Heated Oxygen Sensor — 1Ignition Coil And Spark Plug — 1Ignition System — 1Knock Sensor — 1Mass Air Flow Meter — 1Relay — 1Sfi System — 1Throttle Body — 1Camshaft — 1Cylinder Block — 1Cylinder Head — 1Cylinder Head Gasket — 1Engine — 1Engine Assembly — 1Engine Unit — 1Front Crankshaft Oil Seal — 1Rear Crankshaft Oil Seal — 1Fuel Filter — 1Fuel Injector — 1Fuel Pressure Regulator — 1Fuel Pump — 1Fuel Sender Gauge Assembly — 1Fuel System — 1Fuel Tank — 1Air Cleaner Filter Element — 1Exhaust Manifold — 1Exhaust Pipe — 1Intake Manifold — 1Intake System — 1Lubrication System — 1Oil And Oil Filter — 1Oil Pan And Oil Level Sensor — 1Oil Pressure Switch — 1Oil Pump — 1Accelerator Pedal Sensor — 1Battery Blower (for Hev Model) — 1Battery Ecu (for Hev Model) — 1Battery Ecu (for Phev Model) — 1Battery Voltage Sensor (for Phev Model) — 1Charge Cable (for Phev Model) — 1Charge Indicator (for Phev Model) — 1Charge Inlet (for Phev Model) — 1Combination Switch — 1Coolant (for Inverter) — 1Cooler (for Phev Model) — 1Electric Vehicle Charger Assembly (for Phev Model) — 1Frame Wire (for Hev Model) — 1Frame Wire (for Phev Model) — 1Heater Relay (for Phev Model) — 1Hv Battery (for Hev Model) — 1Hv Battery (for Phev Model) — 1Hv Battery Heater (for Phev Model) — 1Hv Battery Stack (for Phev Model) — 1Hv Relay Assembly (for Hev Model) — 1Hv Relay Assembly (for Phev Model) — 1Hybrid Battery System (for 2zr-fxe) — 1Hybrid Battery System (for M20a-fxs) — 1Hybrid Battery System (for Phev Model) — 1Hybrid Vehicle Control Ecu — 1Inverter With Converter (for Hev Model) — 1Motor Generator Control System (for 2zr-fxe) — 1Plug-in Charge Control System (for Phev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Service Plug Grip (for Hev Model) — 1Sub Radiator — 1Water Pump With Motor — 1Auxiliary Battery — 1Battery Current Sensor — 1Charging System — 1Solar Charging System — 1Solar Control Unit — 1Solar Roof — 1Can Communication System (for Hev Model) — 1Lin Communication System — 1Network Gateway Ecu — 1Integration Control Supply — 1Main Body Ecu — 1Power Integration System — 1Sub Battery System — 1Power Steering Ecu — 1Power Steering System — 1Heated Steering Wheel Controller — 1Heated Steering Wheel System — 1Steering Column Assembly — 1Steering Heater Switch — 1Steering Pad Switch — 1Steering System — 1Steering Wheel — 1Front Lower Ball Joint — 1Front Lower Suspension Arm (for 2zr-fxe Lh Side) — 1Front Lower Suspension Arm (for 2zr-fxe Rh Side) — 1Front Lower Suspension Arm (for M20a-fxs) — 1Front Shock Absorber — 1Front Stabilizer Bar — 1Front Suspension Member — 1Rear Coil Spring — 1Rear Lower Arm (for Awd Lh Side) — 1Rear Lower Arm (for Awd Rh Side) — 1Rear Lower Arm (for Hev Model 2wd) — 1Rear Lower Arm (for Phev Model) — 1Rear Shock Absorber — 1Rear Stabilizer Bar — 1Rear Suspension Member (for 2wd) — 1Rear Suspension Member (for Awd) — 1Rear Trailing Arm — 1Rear Upper Arm — 1Tire And Wheel System — 1Tire Repair Seal — 1Tire Pressure Warning Receiver — 1Tire Pressure Warning System — 1Tire Pressure Warning Valve — 1Acoustic Vehicle Alerting System — 1Vehicle Approaching Speaker — 1Vehicle Approaching Speaker Ecu — 1Back Door — 1Back Door Closer Ecu — 1Back Door Opener Switch — 1Back Door Support — 1Back Door Weatherstrip — 1Charge Lid Courtesy Switch — 1Charge Lid Opener Motor Assembly — 1Charge Lid Opener System — 1Charge Lid Opener Unit — 1Front Door — 1Front Door Opening Trim Weatherstrip — 1Fuel Lid Opener Motor Assembly — 1Fuel Lid Opener Switch — 1Fuel Lid Opener System — 1Hood — 1Hood Lock Control Cable Assembly — 1Power Back Door Closer Switch — 1Power Back Door Control Switch — 1Power Back Door Drive Unit — 1Power Back Door System — 1Power Back Door Touch Sensor — 1Power Back Door Warning Buzzer — 1Rear Door — 1Rear Door Opening Trim Weatherstrip — 1Reserve Lock Switch — 1Front Bumper — 1Front Door Belt Moulding — 1Front Door Window Frame Moulding — 1Front Fender — 1Front Pillar Upper Cover — 1Grille Shutter — 1Grille Shutter System — 1Name Plate — 1Quarter Garnish — 1Rear Bumper — 1Rear Door Belt Moulding — 1Rear Door Window Frame Moulding — 1Rear Wheel House Plate — 1Rocker Panel Moulding — 1Roof Drip Side Finish Moulding — 1Roof Garnish — 1Wheel Opening Moulding (for Front Side) — 1Wheel Opening Moulding (for Rear Side) — 1Windshield Outside Moulding — 1Horn — 1Horn System — 1Relay — 1Automatic Light Control Sensor — 1Back-up Light Assembly — 1Charge Lid Light — 1Front Marker Light — 1Hazard Warning Switch — 1Headlight Assembly — 1Headlight Dimmer Switch — 1Headlight Leveling Switch — 1High Mounted Stop Light Assembly — 1Illumination Light Assembly — 1License Plate Light Assembly — 1Lighting System — 1Rear Combination Light Assembly — 1Rear Light Assembly — 1Rear Side Marker Light Assembly — 1Relay — 1Side Turn Signal Light Assembly — 1Stop Light Switch — 1Switch Housing — 1Outer Mirror Switch — 1Outer Rear View Mirror — 1Outer Rear View Mirror Cover — 1Outer Rear View Mirror Glass — 1Power Mirror Control System — 1Back Door Glass — 1Front Passenger Side Power Window Switch — 1Power Window Control System — 1Power Window Master Switch — 1Power Window Regulator Motor (for Front Door) — 1Power Window Regulator Motor (for Rear Door) — 1Rear Power Window Switch — 1Relay — 1Roof Window Fix Glass — 1Window Defogger System — 1Windshield Deicer Switch — 1Windshield Deicer System — 1Windshield Glass — 1Front Wiper Motor — 1Rain Sensor — 1Relay — 1Washer Motor — 1Washer Nozzle (for Front Side) — 1Washer Nozzle (for Rear Television Camera) — 1Wiper And Washer System — 1Wiper Ecu — 1Wiper Switch — 1Back Door Lock — 1Door Control Receiver — 1Door Control Switch — 1Door Control Transmitter — 1Door Lock Release Motor (for Rear Side) — 1Door Outside Handle (for Rear Side) — 1Front Door Lock — 1Power Door Lock Control System — 1Rear Door Lock — 1Transmitter Battery — 1Wireless Door Lock Control System — 1Accumulator — 1Air Conditioning Amplifier — 1Air Conditioning Panel — 1Air Conditioning Pressure Sensor — 1Air Conditioning Unit — 1Ambient Temperature Sensor — 1Blower Unit — 1Condenser (for Hev Model) — 1Condenser (for Phev Model) — 1Discharge Temperature Sensor — 1Electric Expansion Valve (cooling) — 1Electric Expansion Valve (heating) — 1Evaporator Pipe Temperature Sensor — 1Evaporator Pressure Regulator — 1Front Blower Motor — 1Front Evaporator Front Solenoid Valve — 1Air Conditioning System (for Hev Model) — 1Front Evaporator Temperature Sensor — 1Heat Exchanger Temperature Sensor — 1Heat Pump Ecu — 1High Pressure Magnetic Valve — 1Humidity Sensor — 1Internal Condenser Temperature Sensor — 1Low Pressure Magnetic Valve — 1Refrigerant (for Hfc-134a(r134a)) — 1Refrigerant Line (for Hev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Room Temperature Sensor — 1Solar Sensor — 1Floor Carpet — 1Front Console Box — 1Instrument Panel Safety Pad — 1Roof Headlining — 1Roof Sunshade — 1Ambient Light (for Driver Side) — 1Ambient Light (for Front Passenger Side) — 1Back Door Courtesy Switch — 1Footwell Light — 1Glove Box Light — 1Lighting System — 1Luggage Compartment Room Light — 1Personal Light — 1Room Light — 1Vanity Light — 1Vanity Light Switch — 1Combination Meter — 1Meter / Gauge System — 1Trip Switch — 1Digital Inner Mirror — 1Digital Rear-view Mirror System — 1Inner Mirror Monitor Camera — 1Inner Rear View Mirror (w/o Ec Mirror) — 1Accessory Power Outlet System — 1Power Outlet Socket (for Console Box Front Side) — 1Power Outlet Socket (for Console Box Rear Side) — 1Power Outlet Socket (for Console Box) — 1Power Outlet Socket (for Luggage Compartment) — 1Power Outlet Switch — 1Wireless Charger Assembly — 1Wireless Charging System — 1Climate Control Seat System — 1Front Power Seat Control System (w/ Memory) — 1Front Power Seat Motor Assembly — 1Front Seat Assembly (for Power Seat) — 1Front Seat Cushion Heater (for Power Seat) — 1Front Seatback Heater (for Power Seat) — 1Lumbar Support Adjuster Assembly — 1Power Seat Control Ecu — 1Power Seat Switch — 1Power Seat Track Rail Assembly — 1Rear Seat Assembly — 1Rear Seat Cushion Heater — 1Rear Seat Reminder System — 1Rear Seatback Heater — 1Seat Heater Control — 1Seat Heater Switch (for Front Seat) — 1Seat Heater Switch (for Rear Side) — 1Seat Heater System — 1Seat Memory Switch — 1Child Restraint Seat Anchor Bracket — 1Front Seat Inner Belt Assembly — 1Front Seat Outer Belt Assembly — 1Occupant Detection Sensor (for Front Passenger Side) — 1Rear Center Seat Outer Belt Assembly — 1Rear Seat Inner Belt Assembly (for Rh Side) — 1Rear Seat Outer Belt Assembly — 1Seat Belt Warning System (w/ Occupant Classification System) — 1Tongue Plate Stopper — 1Airbag System — 1Center Airbag Sensor Assembly — 1Curtain Shield Airbag Assembly — 1Front Airbag Sensor — 1Front Passenger Airbag Assembly — 1Front Seat Side Airbag Assembly — 1Inspection After Collision — 1Knee Airbag Assembly — 1Occupant Classification System — 1Rear Seat Side Airbag Assembly — 1Side Airbag Sensor (for Center Pillar) — 1Side Airbag Sensor (for Front Door) — 1Spiral Cable — 1Steering Pad — 1Certification Ecu — 1Digital Key Ecu — 1Digital Key Receiver (for Front Floor) — 1Digital Key Receiver (for Outside Luggage Compartment) — 1Digital Key Receiver (for Rear Door) — 1Digital Key System — 1Electrical Key Oscillator (for Front Floor) — 1Electrical Key Oscillator (for Outside Luggage Compartment) — 1Electrical Key Oscillator (for Rear Floor) — 1Engine Hood Courtesy Switch — 1Id Code Box — 1Smart Key System (for Start Function) — 1
17steps
~102min
5/5difficulty
Done 0 of 17
  • Precaution
  • Parts Location
  • System Diagram
  • How To Proceed With Troubleshooting
  • Operation Check
  • Customize Parameters
  • Problem Symptoms Table
  • Terminals Of Ecu
  • Data List / Active Test
  • Wireless Door Lock Tuner Component Internal Failure (B124296)
  • No Answer-Back

Precaution

PRECAUTION

PRECAUTION FOR DISCONNECTING CABLE FROM NEGATIVE (-) AUXILIARY BATTERY TERMINAL

NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click here

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click here

PRECAUTIONS FOR REMOVAL, INSTALLATION AND REPLACEMENT OF COMPONENTS

(a) After replacing certain components, it may be necessary to update the ECU security key.

Click here

PRECAUTIONS WHEN USING GTS

(a) When using the GTS with the ignition switch off, perform lock and unlock operations using the door control switch of the multiplex network master switch assembly at intervals of 1.5 seconds or less until communication between the GTS and the Toyota Prius vehicle begins, and then select the vehicle model manually. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Smart Key. While using the GTS, periodically perform lock and unlock operations using the door control switch of the multiplex network master switch assembly at intervals of 1.5 seconds or less to maintain communication between the GTS and the Toyota Prius vehicle.

REPLACEMENT PRECAUTIONS

(a) Before replacing any of the following parts, refer to Registration.

Click here

  • Certification ECU (smart key ECU assembly)
  • Electrical key transmitter sub-assembly
  • Main body ECU (multiplex network body ECU)

(b) Electrical key and tire pressure monitoring system receiver assembly.

(1) When replacing the electrical key and tire pressure monitoring system receiver assembly, read the transmitter IDs (tire pressure warning system) stored in the old ECU using the GTS and write them down before removal.

Click here

(2) If the electrical key and tire pressure monitoring system receiver assembly has been replaced, it is necessary to perform initialization (Click here ) after registration (Click here ) of the transmitter IDs to the electrical key and tire pressure monitoring system receiver assembly.

PRECAUTIONS FOR ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

Click here

NOTICE WHEN CHECKING FOLLOWING

(a) Wireless door lock/unlock function:

This wireless door lock control function operates only when the following 3 conditions are met:

(1) The ignition switch is off.

(2) All of the doors are closed.*

  • *: When the Wireless Lock Function with Doors Open customize setting is set to Disable

(3) The power door lock control system is operating properly.

HINT:

The unlock function operates even when a door is open.

(b) The size of the wireless door lock control operation area differs depending on the situation.

(1) The size of the operation area differs depending on the user and the way the electrical key transmitter sub-assembly is held.

(2) In certain areas, the wireless door lock control function will only operate partially for the operation area, which will be reduced due to the Toyota Prius vehicle body shape and the influence of the surrounding environment.

(3) Since the electrical key transmitter sub-assembly uses weak radio waves, strong radio waves or electrical noise in the frequency used by the electrical key transmitter sub-assembly may reduce the size of the operation area and the remote control may not function.

(4) When the transmitter battery is weak, the size of the operation area is reduced and the remote control may not function.

HINT:

  • If the electrical key transmitter sub-assembly has been left in a place that is exposed to direct sunlight, such as on the instrument panel, it may cause the battery to be weakened or cause other related problems.
  • Do not place the electrical key transmitter sub-assembly near magnetic equipment, such as digital audio players, induction cookers, medical devices that generate low-frequency electromagnetic waves, etc.

(c) Multi channel function

The wireless door lock control system has a multi channel function. Each time the switch on the electrical key transmitter sub-assembly is pressed, the channel is switched alternately between 2 different frequencies and the signal is sent to the electrical key and tire pressure monitoring system receiver assembly.

Parts Location

PARTS LOCATION

ILLUSTRATION

*1

WIRELESS DOOR LOCK BUZZER

(Toyota Prius Vehicle APPROACHING SPEAKER ASSEMBLY)

*2

ELECTRICAL KEY AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY

ILLUSTRATION

*1

MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

*2

COMBINATION METER ASSEMBLY

*3

DLC3

*4

CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

*5

POWER DISTRIBUTION BOX ASSEMBLY

*6

Toyota Prius Vehicle APPROACHING SPEAKER CONTROLLER

System Diagram

SYSTEM DIAGRAM

POWER DOOR LOCK CONTROL SYSTEM

Click here

How To Proceed With Troubleshooting

NOTICE:

Make sure to check the following before proceeding with troubleshooting.

  • Do not perform "Smart Code Reset" (all key ID erasure) until the malfunctions and symptoms have been confirmed and resolved. If all key ID erasure is performed without confirming or resolving malfunctions, key registration will be unable to be performed, resulting in unnecessary part replacement.
  • Make sure that the smart key system with push-button start has not been disabled by a customize setting.

HINT:

  • Replace parts related to the wireless door lock control system and smart key system with push-button start according to the inspection procedure.
  • If the wireless door lock control system and smart key system with push-button start do not operate, check the customize setting and make sure that the wireless door lock control system and smart key system with push-button start are not disabled.
  • The wireless door lock control system and smart key system with push-button start primarily use the following systems.
    • Wireless door lock control system
    • Smart key system (for Entry Function)*
    • Smart key system (for Start Function)
      • Immobilizer function
  • If 2 or more electrical key transmitter sub-assemblies are registered to the system, make sure to perform troubleshooting with all of them.
  • *: w/ Entry Function

PROCEDURE

  1. Toyota Prius Vehicle BROUGHT TO WORKSHOP

(a) Confirm how the vehicle was brought to the workshop.

  • Vehicle was driven.
  • Vehicle was towed.

HINT:

The cause of the malfunction may be narrowed down by confirming whether the vehicle was driven or towed.

NEXT

GO TO SMART KEY SYSTEM (for Start Function)

Operation Check

OPERATION CHECK

NOTICE:

Make sure that the vehicle is in an area that allows the wireless control function to operate.

HINT:

  • The switches described in this text are the switches for transmitting signals. The switches are built into the electrical key transmitter sub-assembly.
  • All the functions listed below must be checked in comparison with the wireless door lock control operation area.

CHECK CUSTOMIZE PARAMETERS

(a) The operation check below is based on the non-customized initial condition of the Toyota Prius vehicle.

Click here

CHECK BASIC FUNCTIONS

(a) Check that the LED of the electrical key transmitter sub-assembly illuminates and turns off 3 times when each switch is pressed and held for 5 seconds.

HINT:

If the transmitter LED illuminates once or twice but not a third time when the switch has been pressed and held for 5 seconds or more, it may have a weak auxiliary battery.

(b) Check that all of the doors lock when the lock switch is pressed.

(c) Check that the driver door unlocks when the unlock switch is pressed once, and all of the doors unlock when pressed twice within 5 seconds.

(d) Check that the back door opens or closes when the power back door switch is pressed and held for 0.8 seconds or more.

CHECK THE CHATTERING PREVENTION FUNCTION

(a) Press and hold the lock or unlock switch on the electrical key transmitter sub-assembly and check that the corresponding operation occurs only once and is not repeated continuously while the switch is held. Then press the switch repeatedly at 1-second intervals, check that the corresponding operation is carried out.

CHECK THE SWITCH OPERATION FAIL-SAFE FUNCTION

(a) Check that the doors cannot be locked/unlocked by operating a switch on an unregistered electrical key transmitter sub-assembly, but that the doors can be locked/unlocked by operating a switch on the registered electrical key transmitter sub-assembly.

CHECK THE AUTOMATIC LOCKING FUNCTION

(a) Check that the doors lock automatically if none of the doors have been opened or all of the doors have not been locked within approximately 60 or 30* seconds of all of the doors being unlocked by pressing the unlock switch.

(b) Check that the automatic locking function does not operate when any door has been opened within approximately 60 or 30* seconds of unlocking the doors by pressing the unlock switch.

(c) Check that the automatic locking function does not operate when all of the doors have been locked manually (such as using key linked operation, or by pressing the lock switch) within approximately 60 or 30* seconds of unlocking the doors by pressing the unlock switch.

  • *: Default setting differs depending on the country.

CHECK THE DOOR AJAR WARNING BUZZER FUNCTION

HINT:

When the Wireless Lock Function with Doors Open customize setting is set to Enable, this function will be disabled even if the Open Door Warning Function customize setting is set to Enable.

(a) Check that the wireless door lock buzzer sounds for approximately 5 seconds when the lock switch is pressed with any of the doors ajar or open.

HINT:

The doors can be unlocked even when a door is open or ajar.

CHECK THE DOOR LOCK STOP FUNCTION THAT OPERATES WHEN A DOOR IS OPEN/AJAR

(a) With a door open or ajar, check that the doors cannot be locked by operating the lock switch.

CHECK THE WIRELESS RESERVATION LOCK FUNCTION (w/ Wireless Reservation Lock Function)

HINT:

When the Wireless Lock Function with Doors Open customize setting is set to Enable, the door ajar warning buzzer function will be disabled even if the Open Door Warning Function customize setting is set to Enable.

(a) Check that the doors are locked by performing a wireless lock operation with any door open.

(b) Check that answer-back (wireless door lock buzzer) function operates when the wireless operation is performed and answer-back (hazard warning light) function operates when the doors are closed.

CHECK THE POWER BACK DOOR RESERVATION LOCK FUNCTION

(a) Check that the doors lock after the back door is closed when the lock switch is pressed during the back door closing operation via the power back door function.

CHECK WIRELESS ONE MOTION FUNCTION

Click here

CHECK THE ANSWER-BACK (HAZARD WARNING LIGHT) FUNCTION

(a) When the lock switch is pressed, check that the hazard warning lights flash once simultaneously with the locking operation of all of the doors.

(b) When the unlock switch is pressed and all of the doors are locked, check that the hazard warning lights flash twice simultaneously with the unlocking operation of all of the doors.

(c) With the back door locked, when the back door open switch is pressed and held for 0.8 seconds or more, check that the hazard warning lights flash twice.

CHECK THE ANSWER-BACK (WIRELESS DOOR LOCK BUZZER) FUNCTION

(a) When the lock switch is pressed, check that the buzzer sounds once simultaneously with the locking operation of all of the doors.

(b) When the unlock switch is pressed and all of the doors are locked, check that the buzzer sounds twice simultaneously with the unlocking operation of all of the doors.

(c) With the back door locked, when the back door open switch is pressed and held for 0.8 seconds or more, check that the wireless door lock buzzer sounds.

CHECK THE PANIC ALARM CONTROL FUNCTION (w/ Panic Function)

(a) Check that the horn sounds, the headlights, taillights, hazard lights flash and the interior lights remain on (when the light switch is turned to the door position) for 60 seconds, when the panic switch is held down for 0.8 seconds or more. Also, check that the horn stops sounding and the lights stop flashing when any switch of the electrical key transmitter sub-assembly is pressed.

CHECK THE ILLUMINATED ENTRY FUNCTION

Click here

CHECK THE POWER WINDOW OPERATION FUNCTION

Click here

Customize Parameters

CUSTOMIZE PARAMETERS

CUSTOMIZE WIRELESS DOOR LOCK CONTROL SYSTEM

NOTICE:

  • When the customer requests a change in a function, first make sure that the function can be customized.
  • Be sure to make a note of the current settings before customizing.
  • When troubleshooting a function, first make sure that the function is set to the default setting.

HINT:

The following items can be customized.

(a) Customizing with the GTS

(1) Connect the GTS to the DLC3.

(2) Turn the ignition switch to ON.

(3) Turn the GTS on.

(4) Enter the following menus: Customize Setting / Wireless Door Lock or Door Lock.

(5) Select the setting by referring to the table below.

Wireless Door Lock

Tester Display

Description

Default

Setting

ECU

Wireless Buzzer Response Function

Function that enables/disables the wireless door lock buzzer response.

Enable

$00:Disable,$01:Enable

Main body ECU (Multiplex network body ECU)

Panic Function

Function that operates the theft deterrent system by pressing the panic switch on the electrical key transmitter sub-assembly for 0.8 seconds.*1

Enable

$00:Disable,$01:Enable

Main body ECU (Multiplex network body ECU)

Hazard Answer Back Function

Function that flashes the hazard warning lights once when the doors are locked by wireless operation and twice when the doors are unlocked by wireless operation.

Enable

$00:Disable,$01:Enable

Main body ECU (Multiplex network body ECU)

Wireless Buzzer Volume Setting

Function that adjusts the wireless door lock buzzer volume.

Level5

$00:Level7(MAX),$01:Level6,$02:Level5,$03:Level4,$04:Level3,$05:Level2,$06:Level1,$07:Level0(MIN)

Main body ECU (Multiplex network body ECU)

Wireless Unlock Twice Function

Function that unlocks the driver door when the unlock switch on the electrical key transmitter sub-assembly is pressed once, and unlocks all of the doors when pressed twice. If this setting is OFF, pressing the unlock switch once unlocks all of the doors.

Enable

$00:Disable,$01:Enable

Main body ECU (Multiplex network body ECU)

Wireless Lock Function with Doors Open

Function that locks the doors automatically if the lock switch on the electrical key transmitter sub-assembly is pressed with any door open and then all of the doors are closed.*2

Enable

$00:Disable,$01:Enable

Main body ECU (Multiplex network body ECU)

  • *1: w/ Panic Function
  • *2: w/ Wireless Reservation Lock Function
Door Lock

Tester Display

Description

Default

Setting

ECU

Automatic Door Lock Function

Function that turns the automatic locking function on or off.*

Enable

$00:Disable,$01:Enable

Main body ECU (Multiplex network body ECU)

Open Door Warning Function

Function that sounds a buzzer when the lock switch is pressed when any of the doors are ajar.

Enable

$00:Disable,$01:Enable

Main body ECU (Multiplex network body ECU)

Door Auto Lock Timer Setting

Function that regulates the interval between unlocking and automatic relocking of the doors.

30sec/60sec*

$00:30sec,$01:60sec,$02:120sec

Main body ECU (Multiplex network body ECU)

  • *: Default setting differs depending on the country.

(b) Customizing with the multi-display

(1) Turn the ignition switch to ON.

(2) Enter the following menus: Settings / Toyota Prius Vehicle customize / Door control.

(3) Select the setting by referring to the table below.

Key settings

Display

Description

Default

Setting

Relevant ECU

Auto relock timer

Function that regulates the interval between unlocking and automatic relocking of the doors

60sec

Off, 30sec, 60sec or 120sec

Main body ECU (Multiplex network body ECU)

Feedback lights

Function that flashes the hazard warning lights once when the doors are locked by wireless operation and twice when the doors are unlocked by wireless operation.

On

On or Off

Main body ECU (Multiplex network body ECU)

Feedback tone

Function that adjusts the wireless door lock buzzer volume

5

Off, 1, 2, 3, 4, 5, 6 or 7

Main body ECU (Multiplex network body ECU)

Wireless electronic key

Display

Description

Default

Setting

Relevant ECU

2-press unlock

Function that unlocks the driver door when the unlock switch on the electrical key transmitter sub-assembly is pressed once, and unlocks all of the doors when pressed twice. If this setting is OFF, pressing the unlock switch once unlocks all of the doors.

Enable

On or Off

Main body ECU (Multiplex network body ECU)

Lock when door opened

Function that locks the doors automatically if the lock switch on the electrical key transmitter sub-assembly is pressed with any door open and then all of the doors are closed.

Enable

On or Off

Main body ECU (Multiplex network body ECU)

Problem Symptoms Table

PROBLEM SYMPTOMS TABLE

HINT:

  • Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
  • Inspect the fuses and relays related to this system before inspecting the suspected areas below.
Wireless Door Lock Control System

Symptom

Suspected Area

Link

Wireless control function and entry function do not operate

Check DTC output

Lighting system (INT)

Power door lock control system

Wave interference

Transmitter battery

Electrical key transmitter sub-assembly

Wire harness or connector

Check connector connection

Electrical key and tire pressure monitoring system receiver assembly

Certification ECU (Smart key ECU assembly)

Main body ECU (Multiplex network body ECU)

B code registration failed

Wireless control function does not operate but entry function operates

Electrical key transmitter sub-assembly

-

Back door does not open when back door open switch operated (Wireless lock/unlock function does not operate)*

Check customize setting (Wireless Unlock Twice Function "Disable")

Power back door system

Only answer-back function does not operate properly

Check customize setting

Perform operation check

Lighting system (INT)

Main body ECU (Multiplex network body ECU)

Lighting system (Ext) (Hazard warning switch circuit)

Wire harness or connector

Acoustic Toyota Prius vehicle alerting system

Power distribution box assembly

Wireless door lock buzzer

Only automatic lock function does not operate properly

Perform operation check

Power door lock control system

Main body ECU (Multiplex network body ECU)

-

Only illuminated entry function does not operate

Perform operation check

Lighting system (Int)

Main body ECU (Multiplex network body ECU)

-

Only door ajar warning buzzer function does not operate

Main body ECU (Multiplex network body ECU)

Acoustic Toyota Prius vehicle alerting system

Only panic alarm function does not operate

Perform operation check

Lighting system (Int) (Interior lights)

Lighting system (Ext) (Headlights, Taillights, Hazard warning lights)

Horn system

Main body ECU (Multiplex network body ECU)

  • *: W/ Power Back Door System

Terminals Of Ecu

TERMINALS OF ECU

CHECK POWER DISTRIBUTION BOX ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

(a) Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.

Click here

(b) Reconnect the power distribution box assembly connectors.

(c) Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

z1-13 (GND1) - Body ground

Ground

Always

Below 1 Ω

z1-14 (GND2) - Body ground

Ground

Always

Below 1 Ω

z1-26 (BECU) - Body ground

Auxiliary battery power supply

Ignition switch off

11 to 14 V

z1-27 (IGR) - Body ground

IG power supply

Ignition switch ON

11 to 14 V

Ignition switch off

Below 1 V

CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

(a) Disconnect the K13 certification ECU (smart key ECU assembly) connector.

(b) Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

K13-6 ( B) - K13-29 (E)

Auxiliary battery power supply

Ignition switch off

11 to 14 V

K13-29 (E) - Body ground

Ground

Always

Below 1 Ω

(c) Reconnect the K13 certification ECU (smart key ECU assembly) connector.

(d) Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

R59-21 (RCO) - K13-29 (E)

Output to electrical key and tire pressure monitoring system receiver assembly

(Power supply for electrical key and tire pressure monitoring system receiver assembly. Certification ECU (smart key ECU assembly) outputs 5 V when receiver starts operating.)

Procedure:
  1. Turn ignition switch off
  2. Bring electrical key transmitter sub-assembly outside detection area but within wireless function operational area
  3. Press lock or unlock switch of electrical key transmitter sub-assembly

Plus generation (See waveform 1)

R59-11 (RDAM) - K13-29 (E)

Electrical key and tire pressure monitoring system receiver assembly communication circuit

Procedure:
  1. Turn ignition switch off
  2. Lock all doors
  3. Bring electrical key transmitter sub-assembly outside detection area but within wireless function operational area
  4. Press lock or unlock switch of electrical key transmitter sub-assembly

Plus generation (See waveform 2)

R59-12 (CSEL) - K13-29 (E)

Communication channel switching circuit

Procedure:
  1. Turn ignition switch off
  2. Close all doors

No pulse generation → Pulse generation

(e) Using an oscilloscope, check waveform 1.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

*a

Before lock or unlock switch of electrical key transmitter sub-assembly pressed

*b

After lock or unlock switch of electrical key transmitter sub-assembly pressed

Waveform 1 (Reference)

Item

Content

Tester connection

R59-21 (RCO) - K13-29 (E)

Tool setting

2 V/DIV., 500 ms/DIV.

Condition

Procedure:

  1. Turn ignition switch off
  2. Bring electrical key transmitter sub-assembly outside detection area but within wireless function operational area
  3. Electrical key transmitter sub-assembly not inside Toyota Prius vehicle
  4. Press lock or unlock switch of electrical key transmitter sub-assembly

(f) Using an oscilloscope, check waveform 2.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

*a

Before lock or unlock switch of electrical key transmitter sub-assembly pressed

*b

After lock or unlock switch of electrical key transmitter sub-assembly pressed

Waveform 2 (Reference)

Item

Content

Tester connection

R59-11 (RDAM) - K13-29 (E)

Tool setting

5 V/DIV., 500 ms/DIV.

Condition

Procedure:

  1. Turn ignition switch off
  2. Lock all doors
  3. Bring electrical key transmitter sub-assembly outside detection area but within wireless function operational area
  4. Press lock or unlock switch of electrical key transmitter sub-assembly

Data List / Active Test

DATA LIST / ACTIVE TEST

DATA LIST

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

(a) Connect the GTS to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the GTS on.

(d) Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

FR Door Lock Position Switch Status

Front door RH lock status

Lock or Unlock

Lock: Front door RH locked

Unlock: Front door RH Unlocked

-

FL Door Lock Position Switch Status

Front door LH lock status

Lock or Unlock

Lock: Front door LH locked

Unlock: Front door LH Unlocked

-

RR Door Lock Position Switch Status

Rear door RH lock status

Lock or Unlock

Lock: Rear door RH locked

Unlock: Rear door RH Unlocked

-

RL Door Lock Position Switch Status

Rear door LH lock status

Lock or Unlock

Lock: Rear door LH locked

Unlock: Rear door LH Unlocked

-

FR Door Courtesy Switch Status

Front door courtesy light switch signal

Close or Open

Close: Front door RH closed

Open: Front door RH open

-

FL Door Courtesy Switch Status

Front door courtesy light switch signal

Close or Open

Close: Front door LH closed

Open: Front door LH open

-

RR Door Courtesy Switch Status

Front door courtesy light switch signal

Close or Open

Close: Rear door RH closed

Open: Rear door RH open

-

RL Door Courtesy Switch Status

Front door courtesy light switch signal

Close or Open

Close: Rear door LH closed

Open: Rear door LH open

-

Back Door Courtesy Switch Status

Back door courtesy light switch signal

Close or Open

Close: Back door closed

Open: Back door open

-

IGR Power

Ignition switch ON signal

Disable or Enable

OFF: Ignition switch off or ACC

ON: Ignition switch ON

-

Automatic Door Lock Function

Wireless auto lock function

Disable or Enable

Customize setting displayed

-

Wireless Buzzer Response Function

Buzzer answer-back of wireless function

Disable or Enable

Customize setting displayed

-

Open Door Warning Function

Open door warning

Disable or Enable

Customize setting displayed

-

Panic Function

Panic function

Disable or Enable

Customize setting displayed

w/ Panic Function

Wireless Unlock Twice Function

2 press wireless unlock function

Disable or Enable

Customize setting displayed

-

Door Auto Lock Timer Setting

Automatic lock time

30sec, 60sec or 120sec

Customize setting displayed

-

Hazard Answer Back Function

Hazard light answer-back of wireless function

Disable or Enable

Customize setting displayed

-

Wireless Buzzer Volume Setting

Wireless door lock buzzer volume

Level7(MAX), Level6, Level5, Level4, Level3, Level2, Level1 or Level0(MIN)

Customize setting displayed

-

Wireless Lock Function with Doors Open

Wireless reservation lock function

Disable or Enable

Customize setting displayed

w/ Wireless Reservation Lock Function

ACTIVE TEST

HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) Connect the GTS to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the GTS on.

(d) Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Door Lock

Door lock signal

OFF/ON

-

Door Unlock

Door unlock signal

OFF/ON

-

D-Door Unlock

Driver door unlock signal

OFF/ON

-

Wireless Door Lock Tuner Component Internal Failure (B124296)

DESCRIPTION

The electrical key and tire pressure monitoring system receiver assembly is used to receive radio waves related to the entry functions of the electrical key transmitter sub-assembly. The certification ECU (smart key ECU assembly) decodes the requested electrical key transmitter sub-assembly operation by identifying a key code based on the radio waves received via the electrical key and tire pressure monitoring system receiver assembly. The electrical key and tire pressure monitoring system receiver assembly receives a signal from the electrical key transmitter sub-assembly and sends signals to the main body ECU (multiplex network body ECU) through the certification ECU (smart key ECU assembly). (ex. If a door lock operation is requested, the certification ECU (smart key ECU assembly) sends a door lock command to the main body ECU (multiplex network body ECU)).

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

DTC Output from

Priority

B124296

Wireless Door Lock Tuner Component Internal Failure

  • Short to ground in RDAM terminal circuit between the certification ECU (smart key ECU assembly) and electrical key and tire pressure monitoring system receiver assembly.
  • Short to ground in RDAM terminal circuit when voltage (5 V) is not being output from terminal RCO
  • Wire harness or connector
  • Electrical key and tire pressure monitoring system receiver assembly
  • Certification ECU (smart key ECU assembly)

Smart Key

A

WIRING DIAGRAM

NOTICE:

  • When using the GTS with the ignition switch off, perform lock and unlock operations using the door control switch of the multiplex network master switch assembly at intervals of 1.5 seconds or less until communication between the GTS and the Toyota Prius vehicle begins, and then select the vehicle model manually. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Smart Key. While using the GTS, periodically perform lock and unlock operations using the door control switch of the multiplex network master switch assembly at intervals of 1.5 seconds or less to maintain communication between the GTS and the Toyota Prius vehicle.
  • Before replacing the certification ECU (smart key ECU assembly), refer to Registration.

    Click here

  • When replacing or inspecting the electrical key and tire pressure monitoring system receiver assembly and wire harness, do not change the position or length of the wire harness. If the wire harness is too close to the electrical key and tire pressure monitoring system receiver assembly, the performance of the entry function and wireless function may be affected.
  • The detection conditions of this DTC cannot be met within 10 seconds of the ignition switch being turned from off to ON or ON to off.
  • Make sure that there are no electrical key transmitter sub-assemblies in the Toyota Prius vehicle.
  • When replacing the electrical key and tire pressure monitoring system receiver assembly, read the transmitter IDs (tire pressure warning system) stored in the old ECU using the GTS and write them down before removal.

    Click here

  • If the electrical key and tire pressure monitoring system receiver assembly has been replaced, it is necessary to perform initialization (Click here ) after registration (Click here ) of the transmitter IDs to the electrical key and tire pressure monitoring system receiver assembly.

PROCEDURE

  1. CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

Pre-procedure1

(a) Disconnect the R31 electrical key and tire pressure monitoring system receiver assembly connector.

Procedure1

(b) Measure the voltage and resistance and check for pulses according to the value(s) in the table below.

*a

Component with harness connected

(Certification ECU (Smart Key ECU Assembly))

-

-

Standard Resistance:

Click Location & Routing(K13) Click Connector(K13)

Tester Connection

Condition

Specified Condition

K13-29 (E) - Body ground

Always

Below 1 Ω

Standard Voltage:

Click Location & Routing(R59,K13) Click Connector(R59) Click Connector(K13)

Tester Connection

Condition

Specified Condition

R59-11 (RDAM) - K13-29 (E)

Always

11 to 14 V

R59-21 (RCO) - K13-29 (E)

Always

Below 1 V → 4.5 to 5.5 V pulse generation at regular intervals

Post-procedure1

(c) None

OK

REPLACE ELECTRICAL KEY AND TIRE PRESURE MONITORING SYSTEM RECEIVER ASSEMBLY

NG
  1. CHECK HARNESS AND CONNECTOR (ELECTRICAL KEY AND TIRE PRESURE MONITORING SYSTEM RECEIVER ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) AND BODY GROUND)

Pre-procedure1

(a) Disconnect the R59 certification ECU (smart key ECU assembly) connector.

Procedure1

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(R31,R59) Click Connector(R31) Click Connector(R59)

Tester Connection

Condition

Specified Condition

R31-2 (DATA) - R59-11 (RDAM)

Always

Below 1 Ω

R31-8 ( 5) - R59-21 (RCO)

Always

Below 1 Ω

R31-12 (GND) - Body ground

Always

Below 1 Ω

R31-2 (DATA) or R59-11 (RDAM) - Other terminals and body ground

Always

10 kΩ or higher

R31-8 ( 5) or R59-21 (RCO) - Other terminals and body ground

Always

10 kΩ or higher

Post-procedure1

(c) None

OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

No Answer-Back

DESCRIPTION

In some cases, wireless door lock control functions are normal but the hazard warning light and wireless door lock buzzer answer-back function do not operate. In such cases, hazard warning light and wireless door lock buzzer signal outputs from the main body ECU (multiplex network body ECU) may be malfunctioning.

WIRING DIAGRAM

NOTICE:

  • The wireless door lock control system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the wireless door lock control system after confirming that the communication system is functioning properly.

    Click here

  • Before replacing the main body ECU (multiplex network body ECU), refer to Registration.

    Click here

  • Before performing the inspection, check that DTC B124296 is not output.

PROCEDURE

  1. CHECK CUSTOMIZE SETTING USING GTS

(a) Select the setting by referring to the table below.

Wireless Door Lock

Tester Display

Description

Default

Setting

ECU

Wireless Buzzer Response Function

Function that enables/disables the wireless door lock buzzer response

Enable

$00:Disable,$01:Enable

Main body ECU (Multiplex network body ECU)

Hazard Answer Back Function

Function that flashes the hazard warning lights once when the doors are locked by wireless operation and twice when the doors are unlocked by wireless operation

Enable

$00:Disable,$01:Enable

Main body ECU (Multiplex network body ECU)

Wireless Buzzer Volume Setting

Function that adjusts the wireless door lock buzzer volume

Level5

$00:Level7(MAX),$01:Level6,$02:Level5,$03:Level4,$04:Level3,$05:Level2,$06:Level1,$07:Level0(MIN)

Main body ECU (Multiplex network body ECU)

Result

Proceed to

All settings are Enable and other than Level0

A

A setting is Disable or Level0

B

B

PERFORM CUSTOMIZE FUNCTION

A
  1. CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS

(a) Check the wireless door lock control function using the electrical key transmitter sub-assembly.

Click here

Result

Proceed to

Wireless door lock/unlock operates properly

A

Wireless door lock/unlock does not operate properly

B

B

GO TO PROBLEM SYMPTOMS TABLE

A
  1. READ VALUE USING GTS

(a) Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

FR Door Lock Position Switch Status

Front door RH lock status

Lock or Unlock

Lock: Front door RH locked

Unlock: Front door RH Unlocked

-

FL Door Lock Position Switch Status

Front door LH lock status

Lock or Unlock

Lock: Front door LH locked

Unlock: Front door LH Unlocked

-

RR Door Lock Position Switch Status

Rear door RH lock status

Lock or Unlock

Lock: Rear door RH locked

Unlock: Rear door RH Unlocked

-

RL Door Lock Position Switch Status

Rear door LH lock status

Lock or Unlock

Lock: Rear door LH locked

Unlock: Rear door LH Unlocked

-

Body Electrical > Main Body > Data List

Tester Display

FR Door Lock Position Switch Status

FL Door Lock Position Switch Status

RR Door Lock Position Switch Status

RL Door Lock Position Switch Status

OK:

The GTS display changes correctly in response to the lock/unlock operation.

NG

GO TO POWER DOOR LOCK CONTROL SYSTEM

OK
  1. CHECK WIRELESS ANSWER-BACK OPERATION

(a) Check the wireless answer-back operation using the electrical key transmitter sub-assembly.

Click here

Result

Proceed to

Only hazard warning light answer-back does not occur.

A

Only wireless door lock buzzer answer-back does not occur.

B

B

GO TO STEP 6

A
  1. CHECK HAZARD WARNING LIGHTS OPERATION

(a) Check that the hazard warning lights blink when the hazard warning signal switch is pressed.

OK:

Hazard warning lights blink.

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

GO TO LIGHTING SYSTEM (Proceed to Hazard Warning Switch Circuit)

  1. CHECK ACOUSTIC Toyota Prius Vehicle ALERTING SYSTEM

(a) Check the acoustic vehicle alerting system.

Click here

OK:

The acoustic vehicle alerting system operates normally.

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

GO TO ACOUSTIC Toyota Prius Vehicle ALERTING SYSTEM