Parking Assist Monitor System

In this manual: Parking Assist Monitor System
How To Troubleshoot Ecu Controlled Systems — 1How To Use This Manual — 1Identification Information — 1Repair Instruction — 1Terms — 12zr-fxe Air Cleaner Filter Element — 12zr-fxe Auxiliary Battery — 12zr-fxe Coolant (for Engine Coolant) — 12zr-fxe Oil And Oil Filter — 12zr-fxe Spark Plug — 1Air Conditioning Filter — 1Battery Cooling Filter — 1Brake Fluid — 1Coolant (for Inverter) — 1Front Brake Flexible Hose — 1Front Disc Brake Pad — 1Front Lower Ball Joint — 1Front Wheel Alignment — 1Front Wiper Rubber — 1General Maintenance — 1M20a-fxs Air Cleaner Filter Element — 1M20a-fxs Auxiliary Battery — 1M20a-fxs Coolant (for Engine Coolant) — 1M20a-fxs Oil And Oil Filter — 1M20a-fxs Spark Plug — 1Pa10/pb10/pb12 Hybrid Transaxle Fluid — 1Q810 Hybrid Transaxle Fluid — 1Rear Brake Flexible Hose — 1Rear Disc Brake Pad — 1Rear Wheel Alignment — 1Steering Column — 1Tire And Wheel — 1Transmitter Battery — 1When Disconnecting Or Reconnecting Battery Terminal — 1When Replacing Or Removing/installing Parts — 1Automatic High Beam Main Switch — 1Automatic High Beam System — 1Driver Monitor Camera — 1Driver Monitor Camera System — 1Driver Monitor Ecu — 1Front Camera — 1Front Camera System — 1Front Radar Sensor System — 1Front Side Radar Sensor — 1Front Side Radar Sensor System — 1Millimeter Wave Radar Sensor — 1Utility — 1Advanced Park — 1Advanced Park Main Switch — 1Amplifier Antenna — 1Audio And Visual System — 1Front Door Speaker — 1Instrument Panel Speaker — 1Microphone — 1Noise Filter — 1Pillar Speaker — 1Radio Antenna Cord (for Back Door) — 1Radio Antenna Cord (for Instrument Panel) — 1Radio Antenna Cord (for Roof) — 1Radio Receiver — 1Rear Door Speaker — 1Roof Antenna — 1Stereo Component Amplifier — 1Stereo Jack Adapter Assembly — 1Window Glass Antenna Wire — 1Back-up Battery — 1Dcm(telematics Transceiver) — 1Manual(sos)switch — 1Safety Connect System — 1Telephone And Gps Antenna (for Front Side) — 1Telephone And Gps Antenna (for Roof Side) — 1Telephone And Gps Antenna Cords — 1Garage Door Opener System (for Digital Inner Mirror) — 1Garage Door Opener System (for Ec Inner Mirror) — 1Blind Spot Monitor Sensor — 1Blind Spot Monitor System — 1Clearance Warning Ecu — 1Intuitive Parking Assist System — 1Panoramic View Monitor Switch — 1Panoramic View Monitor System — 1Parking Assist Ecu — 1Parking Assist Light — 1Parking Assist Monitor System — 1Parking Support Brake System — 1Rear View Monitor System — 1Television Camera (for Front) — 1Television Camera (for Rear) — 1Television Camera (for Side) — 1Ultrasonic Sensor (for Front) — 1Ultrasonic Sensor (for Rear) — 1Brake Actuator — 1Brake Pedal Stroke Sensor — 1Electronically Controlled Brake System — 1Front Speed Sensor — 1Rear Speed Sensor (for Awd) — 1Steering Angle Sensor — 1Brake Booster — 1Brake Fluid — 1Brake Line — 1Brake Pedal — 1Brake System — 1Electric Parking Brake Actuator — 1Electric Parking Brake Switch — 1Electric Parking Brake System — 1Forced Release — 1Front Axle Hub — 1Front Axle Hub Bolt — 1Rear Axle Carrier (for 2wd) — 1Rear Axle Carrier (for Awd) — 1Rear Axle Hub (for 2wd) — 1Rear Axle Hub (for Awd) — 1Rear Axle Hub Bolt — 1Steering Knuckle — 1Drive Shaft System — 1Front Drive Shaft Assembly — 1Rear Drive Shaft Assembly — 1Combination Switch — 1Electronic Shift Lever System — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Oil Seal — 1Hybrid Transaxle System — 1Input Shaft Oil Seal — 1Motor Cable — 1Pa10 Hybrid Vehicle Transaxle — 1Pa10 Manual Parking Lock Release — 1Pa10 Oil Cooler — 1Pb10/pb12 Hybrid Vehicle Transaxle — 1Pb10/pb12 Manual Parking Lock Release — 1Pb10/pb12 Oil Cooler — 1Shift Control Actuator — 1Shift Lever — 1Shift Lever Knob — 1Differential Side Gear Shaft — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Side Gear Oil Seal — 1Motor Cable — 1Rear Traction Motor — 1Coolant (for Engine) — 1Cooling Fan Motor — 1Cooling Fan System — 1Radiator — 1Relay — 1Thermostat — 1Water Pump — 1Canister — 1Egr Cooler — 1Egr Valve — 1Emission Control System — 1Fuel Tank Cap — 1Pcv Valve — 1Purge Valve — 1Vacuum Sensor — 1Air Fuel Ratio Sensor — 1Camshaft Oil Control Valve — 1Camshaft Position Sensor — 1Crankshaft Position Sensor — 1Ecm — 1Engine Coolant Temperature Sensor — 1Heated Oxygen Sensor — 1Ignition Coil And Spark Plug — 1Ignition System — 1Knock Sensor — 1Mass Air Flow Meter — 1Relay — 1Sfi System — 1Throttle Body — 1Camshaft — 1Cylinder Block — 1Cylinder Head — 1Cylinder Head Gasket — 1Engine — 1Engine Assembly — 1Engine Unit — 1Front Crankshaft Oil Seal — 1Rear Crankshaft Oil Seal — 1Fuel Filter — 1Fuel Injector — 1Fuel Pressure Regulator — 1Fuel Pump — 1Fuel Sender Gauge Assembly — 1Fuel System — 1Fuel Tank — 1Air Cleaner Filter Element — 1Exhaust Manifold — 1Exhaust Pipe — 1Intake Manifold — 1Intake System — 1Lubrication System — 1Oil And Oil Filter — 1Oil Pan And Oil Level Sensor — 1Oil Pressure Switch — 1Oil Pump — 1Accelerator Pedal Sensor — 1Battery Blower (for Hev Model) — 1Battery Ecu (for Hev Model) — 1Battery Ecu (for Phev Model) — 1Battery Voltage Sensor (for Phev Model) — 1Charge Cable (for Phev Model) — 1Charge Indicator (for Phev Model) — 1Charge Inlet (for Phev Model) — 1Combination Switch — 1Coolant (for Inverter) — 1Cooler (for Phev Model) — 1Electric Vehicle Charger Assembly (for Phev Model) — 1Frame Wire (for Hev Model) — 1Frame Wire (for Phev Model) — 1Heater Relay (for Phev Model) — 1Hv Battery (for Hev Model) — 1Hv Battery (for Phev Model) — 1Hv Battery Heater (for Phev Model) — 1Hv Battery Stack (for Phev Model) — 1Hv Relay Assembly (for Hev Model) — 1Hv Relay Assembly (for Phev Model) — 1Hybrid Battery System (for 2zr-fxe) — 1Hybrid Battery System (for M20a-fxs) — 1Hybrid Battery System (for Phev Model) — 1Hybrid Vehicle Control Ecu — 1Inverter With Converter (for Hev Model) — 1Motor Generator Control System (for 2zr-fxe) — 1Plug-in Charge Control System (for Phev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Service Plug Grip (for Hev Model) — 1Sub Radiator — 1Water Pump With Motor — 1Auxiliary Battery — 1Battery Current Sensor — 1Charging System — 1Solar Charging System — 1Solar Control Unit — 1Solar Roof — 1Can Communication System (for Hev Model) — 1Lin Communication System — 1Network Gateway Ecu — 1Integration Control Supply — 1Main Body Ecu — 1Power Integration System — 1Sub Battery System — 1Power Steering Ecu — 1Power Steering System — 1Heated Steering Wheel Controller — 1Heated Steering Wheel System — 1Steering Column Assembly — 1Steering Heater Switch — 1Steering Pad Switch — 1Steering System — 1Steering Wheel — 1Front Lower Ball Joint — 1Front Lower Suspension Arm (for 2zr-fxe Lh Side) — 1Front Lower Suspension Arm (for 2zr-fxe Rh Side) — 1Front Lower Suspension Arm (for M20a-fxs) — 1Front Shock Absorber — 1Front Stabilizer Bar — 1Front Suspension Member — 1Rear Coil Spring — 1Rear Lower Arm (for Awd Lh Side) — 1Rear Lower Arm (for Awd Rh Side) — 1Rear Lower Arm (for Hev Model 2wd) — 1Rear Lower Arm (for Phev Model) — 1Rear Shock Absorber — 1Rear Stabilizer Bar — 1Rear Suspension Member (for 2wd) — 1Rear Suspension Member (for Awd) — 1Rear Trailing Arm — 1Rear Upper Arm — 1Tire And Wheel System — 1Tire Repair Seal — 1Tire Pressure Warning Receiver — 1Tire Pressure Warning System — 1Tire Pressure Warning Valve — 1Acoustic Vehicle Alerting System — 1Vehicle Approaching Speaker — 1Vehicle Approaching Speaker Ecu — 1Back Door — 1Back Door Closer Ecu — 1Back Door Opener Switch — 1Back Door Support — 1Back Door Weatherstrip — 1Charge Lid Courtesy Switch — 1Charge Lid Opener Motor Assembly — 1Charge Lid Opener System — 1Charge Lid Opener Unit — 1Front Door — 1Front Door Opening Trim Weatherstrip — 1Fuel Lid Opener Motor Assembly — 1Fuel Lid Opener Switch — 1Fuel Lid Opener System — 1Hood — 1Hood Lock Control Cable Assembly — 1Power Back Door Closer Switch — 1Power Back Door Control Switch — 1Power Back Door Drive Unit — 1Power Back Door System — 1Power Back Door Touch Sensor — 1Power Back Door Warning Buzzer — 1Rear Door — 1Rear Door Opening Trim Weatherstrip — 1Reserve Lock Switch — 1Front Bumper — 1Front Door Belt Moulding — 1Front Door Window Frame Moulding — 1Front Fender — 1Front Pillar Upper Cover — 1Grille Shutter — 1Grille Shutter System — 1Name Plate — 1Quarter Garnish — 1Rear Bumper — 1Rear Door Belt Moulding — 1Rear Door Window Frame Moulding — 1Rear Wheel House Plate — 1Rocker Panel Moulding — 1Roof Drip Side Finish Moulding — 1Roof Garnish — 1Wheel Opening Moulding (for Front Side) — 1Wheel Opening Moulding (for Rear Side) — 1Windshield Outside Moulding — 1Horn — 1Horn System — 1Relay — 1Automatic Light Control Sensor — 1Back-up Light Assembly — 1Charge Lid Light — 1Front Marker Light — 1Hazard Warning Switch — 1Headlight Assembly — 1Headlight Dimmer Switch — 1Headlight Leveling Switch — 1High Mounted Stop Light Assembly — 1Illumination Light Assembly — 1License Plate Light Assembly — 1Lighting System — 1Rear Combination Light Assembly — 1Rear Light Assembly — 1Rear Side Marker Light Assembly — 1Relay — 1Side Turn Signal Light Assembly — 1Stop Light Switch — 1Switch Housing — 1Outer Mirror Switch — 1Outer Rear View Mirror — 1Outer Rear View Mirror Cover — 1Outer Rear View Mirror Glass — 1Power Mirror Control System — 1Back Door Glass — 1Front Passenger Side Power Window Switch — 1Power Window Control System — 1Power Window Master Switch — 1Power Window Regulator Motor (for Front Door) — 1Power Window Regulator Motor (for Rear Door) — 1Rear Power Window Switch — 1Relay — 1Roof Window Fix Glass — 1Window Defogger System — 1Windshield Deicer Switch — 1Windshield Deicer System — 1Windshield Glass — 1Front Wiper Motor — 1Rain Sensor — 1Relay — 1Washer Motor — 1Washer Nozzle (for Front Side) — 1Washer Nozzle (for Rear Television Camera) — 1Wiper And Washer System — 1Wiper Ecu — 1Wiper Switch — 1Back Door Lock — 1Door Control Receiver — 1Door Control Switch — 1Door Control Transmitter — 1Door Lock Release Motor (for Rear Side) — 1Door Outside Handle (for Rear Side) — 1Front Door Lock — 1Power Door Lock Control System — 1Rear Door Lock — 1Transmitter Battery — 1Wireless Door Lock Control System — 1Accumulator — 1Air Conditioning Amplifier — 1Air Conditioning Panel — 1Air Conditioning Pressure Sensor — 1Air Conditioning Unit — 1Ambient Temperature Sensor — 1Blower Unit — 1Condenser (for Hev Model) — 1Condenser (for Phev Model) — 1Discharge Temperature Sensor — 1Electric Expansion Valve (cooling) — 1Electric Expansion Valve (heating) — 1Evaporator Pipe Temperature Sensor — 1Evaporator Pressure Regulator — 1Front Blower Motor — 1Front Evaporator Front Solenoid Valve — 1Air Conditioning System (for Hev Model) — 1Front Evaporator Temperature Sensor — 1Heat Exchanger Temperature Sensor — 1Heat Pump Ecu — 1High Pressure Magnetic Valve — 1Humidity Sensor — 1Internal Condenser Temperature Sensor — 1Low Pressure Magnetic Valve — 1Refrigerant (for Hfc-134a(r134a)) — 1Refrigerant Line (for Hev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Room Temperature Sensor — 1Solar Sensor — 1Floor Carpet — 1Front Console Box — 1Instrument Panel Safety Pad — 1Roof Headlining — 1Roof Sunshade — 1Ambient Light (for Driver Side) — 1Ambient Light (for Front Passenger Side) — 1Back Door Courtesy Switch — 1Footwell Light — 1Glove Box Light — 1Lighting System — 1Luggage Compartment Room Light — 1Personal Light — 1Room Light — 1Vanity Light — 1Vanity Light Switch — 1Combination Meter — 1Meter / Gauge System — 1Trip Switch — 1Digital Inner Mirror — 1Digital Rear-view Mirror System — 1Inner Mirror Monitor Camera — 1Inner Rear View Mirror (w/o Ec Mirror) — 1Accessory Power Outlet System — 1Power Outlet Socket (for Console Box Front Side) — 1Power Outlet Socket (for Console Box Rear Side) — 1Power Outlet Socket (for Console Box) — 1Power Outlet Socket (for Luggage Compartment) — 1Power Outlet Switch — 1Wireless Charger Assembly — 1Wireless Charging System — 1Climate Control Seat System — 1Front Power Seat Control System (w/ Memory) — 1Front Power Seat Motor Assembly — 1Front Seat Assembly (for Power Seat) — 1Front Seat Cushion Heater (for Power Seat) — 1Front Seatback Heater (for Power Seat) — 1Lumbar Support Adjuster Assembly — 1Power Seat Control Ecu — 1Power Seat Switch — 1Power Seat Track Rail Assembly — 1Rear Seat Assembly — 1Rear Seat Cushion Heater — 1Rear Seat Reminder System — 1Rear Seatback Heater — 1Seat Heater Control — 1Seat Heater Switch (for Front Seat) — 1Seat Heater Switch (for Rear Side) — 1Seat Heater System — 1Seat Memory Switch — 1Child Restraint Seat Anchor Bracket — 1Front Seat Inner Belt Assembly — 1Front Seat Outer Belt Assembly — 1Occupant Detection Sensor (for Front Passenger Side) — 1Rear Center Seat Outer Belt Assembly — 1Rear Seat Inner Belt Assembly (for Rh Side) — 1Rear Seat Outer Belt Assembly — 1Seat Belt Warning System (w/ Occupant Classification System) — 1Tongue Plate Stopper — 1Airbag System — 1Center Airbag Sensor Assembly — 1Curtain Shield Airbag Assembly — 1Front Airbag Sensor — 1Front Passenger Airbag Assembly — 1Front Seat Side Airbag Assembly — 1Inspection After Collision — 1Knee Airbag Assembly — 1Occupant Classification System — 1Rear Seat Side Airbag Assembly — 1Side Airbag Sensor (for Center Pillar) — 1Side Airbag Sensor (for Front Door) — 1Spiral Cable — 1Steering Pad — 1Certification Ecu — 1Digital Key Ecu — 1Digital Key Receiver (for Front Floor) — 1Digital Key Receiver (for Outside Luggage Compartment) — 1Digital Key Receiver (for Rear Door) — 1Digital Key System — 1Electrical Key Oscillator (for Front Floor) — 1Electrical Key Oscillator (for Outside Luggage Compartment) — 1Electrical Key Oscillator (for Rear Floor) — 1Engine Hood Courtesy Switch — 1Id Code Box — 1Smart Key System (for Start Function) — 1
2steps
~12min
2/5difficulty
Done 0 of 2
  • Precaution
  • Parts Location
  • System Diagram
  • How To Proceed With Troubleshooting
  • Customize Parameters
  • Calibration
  • Utility
  • Problem Symptoms Table
  • Terminals Of Ecu
  • Diagnosis System
  • Freeze Frame Data
  • Fail-safe Chart
  • Data List / Active Test
  • Diagnostic Trouble Code Chart
  • VEHICLE CONTROL HISTORY (RoB)
  • Camera Malfunction System Internal Failure (C161704,C161B04)
  • Lost Communication with Steering Angle Sensor Module Missing Message (U012687,U012987,U013187,U014087,U015587,U016387,U029387,U111087)
  • Image from Camera for Parking Assist Monitor is Abnormal

Precaution

PRECAUTION

PRECAUTION FOR DISCONNECTING CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click here

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click here

POINTS TO NOTE WHEN SERVICING

(a) Pay attention to the following points when servicing.

(1) Depending on the parts that are replaced or operations that are performed during Toyota Prius vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.

Click here

HINT:

Each adjusted value for the calibration of the parking assist monitor system will be stored in the radio and display receiver assembly.

(2) A clear image may not be displayed if there is foreign matter such as water drops, snow or mud on the television camera lens. In such a case, wash the lens with a large amount of water and then wipe it with a soft wet cloth. Do not scrub the camera lens as scrubbing may scratch the camera lens and affect the quality of the image.

NOTES FOR REAR TELEVISION CAMERA ASSEMBLY

(a) Notes for the rear television camera assembly

(1) The parking assist monitor system may not function properly if subjected to a severe blow by any hard object.

(2) The cover part of the camera is made of resin. If any organic solvent, degreaser, wax or glass coating contacts the cover, immediately wipe it off and wash the cover with water or cracks may develop.

(3) Exposing the camera to a sudden temperature change may affect proper functioning of the camera.

(4) A clear image may not be displayed if there is foreign matter such as water drops, snow or mud on the television camera lens. In such a case, wash the lens with a large amount of water and then wipe it with a soft wet cloth. Do not scrub the camera lens as scrubbing may scratch the camera lens and affect the quality of the image.

(5) When washing the Toyota Prius vehicle with a high-pressure washer, do not spray water on the rear television camera assembly or surrounding area. High-pressure water can damage the camera.

(b) Images may be unclear even in normal conditions if:

(1) Electrical devices are used in the cabin (noise may occur in the image).

(2) Accessories that generate radio waves have been installed (noise may occur in the image).

(3) The display of radio and display receiver assembly is cold (the image immediately after turning the ignition switch to ON may be blurred or darker than normal).

(4) The camera lens is dirty with snow, mud, etc.

(5) A strong beam of light, such as a sunbeam or headlight, hits the camera.

(6) It is too dark around the camera (at night, etc.).

(7) The ambient temperature around the camera is either too high or too low.

(8) The Toyota Prius vehicle is tilted at a steep angle.

(9) The rear television camera assembly lens is scratched.

(10) The rear television camera assembly lens has drops of water on it or the humidity is high.

(11) When the camera is used under fluorescent lights, sodium lights, mercury lights, etc., the lights and the illuminated area may appear to flicker.

PRECAUTIONS FOR USING REAR CAMERA DETECTION FUNCTION (w/ Rear Camera Detection Function)

(a) a. The rear camera detection function may not be able to detect pedestrians correctly in the following situations:

(1) Pedestrians who are bending forward or squatting

(2) Pedestrians who are laying down

(3) Pedestrians who are running

(4) Pedestrians who suddenly appear from the shadow of the Toyota Prius vehicle or a building

(5) Pedestrians who are riding moving objects such as a bicycle, skateboard, etc.

(6) Pedestrians wearing oversized clothing such as a rain coat, long skirt, etc., making their silhouette obscure

(7) Pedestrians at night or whose clothing appears to be nearly the same color or brightness as their surroundings.

(8) Pedestrians behind an object such as a cart or luggage that hides part of their body

(9) At night (after sunset)

(10) During bad weather (rain, snow, fog, etc.)

(11) Damaged or dirty lens (dirt, snow-melting agent, etc.)

(12) Backlight (direct sunlight, sunlight reflected off the road surface, headlights of other Toyota Prius vehicles, etc.)

(13) Difference in brightness (near open shutters in a garage or underground parking area)

(b) The rear camera detection function may not perform valid detection in the following conditions:

(1) Solid objects (pillars, pylons, fences, parked vehicles, etc.)

(2) Moving objects (passing Toyota Prius vehicle, motorcycle, etc.)

(3) Moving objects (such as flags, exhaust gas, large drops of rain, large snowflakes, rainwater on roads, etc.)

(4) Patterns on roads (white lines, pedestrian crossings, stones, streetcar rails, repaired areas, fallen leaves, gravel, etc.)

(5) A metal cover (grating) or drainage ditch

(6) Shoulders and ridges

(7) Surrounding objects reflected off puddles or wet road surfaces

(8) Shadows

(9) When driving over an uneven surface

(10) The Toyota Prius vehicle is extremely tilted (loaded, suddenly braking, etc.)

(11) There are changes in gradient

(12) A lowered suspension or tire with a different diameter than a genuine tire, etc. is installed

(13) An extreme change in vehicle height (such as nose up, nose down, etc.)

(14) An aftermarket accessory (backlit license plate, fog light, etc.) is installed near the rear camera

(15) An aftermarket protective part is installed to the rear bumper (bumper trim, etc.)

(16) The axis of the camera is misaligned (due to reinstallation, collision, etc.)

(17) A towing hook is installed

(18) The camera lens is dirty (mud, snow-melting agent, etc.)

(19) Water drops are moving over the camera lens

(20) There is a flashing light source (hazard lights, etc.)

(c) Regarding the visibility of the radio and display receiver assembly

(1) When the temperature inside the Toyota Prius vehicle is extremely high or extremely low, the radio and display receiver assembly may not correctly display detection.

(d) Regarding the audibility of the buzzer sound

(1) If the volume setting of the audio system is high, it may be difficult to hear the buzzer.

PRECAUTIONS FOR RECORDED DATA (w/ Rear Camera Detection Function)

(a) The parking assist monitor system records data related to Toyota Prius vehicle control and operation. Make sure to clear the data if requested by the customer.

Click here

Parts Location

PARTS LOCATION

ILLUSTRATION

*1

REAR TELEVISION CAMERA ASSEMBLY

*2

BRAKE ACTUATOR ASSEMBLY

- NO. 2 SKID CONTROL ECU

ILLUSTRATION

*1

HYBRID Toyota Prius Vehicle CONTROL ECU

*2

RADIO AND DISPLAY RECEIVER ASSEMBLY

*3

MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

*4

STEERING SENSOR

*5

CLEARANCE WARNING ECU ASSEMBLY

*6

COMBINATION METER ASSEMBLY

*7

POWER STEERING ECU

*8

DLC3

System Diagram

SYSTEM DIAGRAM

How To Proceed With Troubleshooting

HINT:

  • Use the following procedure to troubleshoot the parking assist monitor system.
  • *: Use the GTS.

PROCEDURE

  1. Toyota Prius Vehicle BROUGHT TO WORKSHOP

NEXT
  1. CUSTOMER PROBLEM ANALYSIS

(a) Ask the customer about the problems and the conditions at the time the malfunction occurred to make sure the problem symptom was not temporarily caused by radio waves in the surrounding environment.

HINT:

The parking assist monitor display may be temporarily distorted due to radio waves around the Toyota Prius vehicle.

Problem Symptom

Cause

The problem symptom indicates a parking assist monitor display malfunction and the problem symptom cannot be reproduced.

The display may be temporarily distorted when the Toyota Prius vehicle is close to an object that transmits radio waves, such as a telecommunication tower, an airport or a truck equipped with a transceiver.

NEXT
  1. INSPECT AUXILIARY BATTERY VOLTAGE

(a) Measure the auxiliary battery voltage with the ignition switch off.

Standard voltage:

11 to 14 V

If the voltage is below 11 V, replace or recharge the auxiliary battery before proceeding to the next step.

NEXT
  1. CHECK AUDIO AND VISUAL SYSTEM

(a) Refer to Audio and Visual System.

Click here

Result

Proceed to

Audio and visual system is normal

A

Audio and visual system is abnormal

B

B

GO TO AUDIO AND VISUAL SYSTEM

A
  1. CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*

(a) Use the GTS to check if the CAN communication system is functioning normally.

Click here

Result

Proceed to

CAN communication system DTCs are not output

A

CAN communication system DTCs are output

B

B

GO TO CAN COMMUNICATION SYSTEM

A
  1. CHECK FOR DTC*

(a) Check for DTCs and make a note of any codes that are output.

Chassis > Rear Camera > Trouble Codes Body Electrical > Navigation System > Trouble Codes

(b) Clear the DTCs.

Chassis > Rear Camera > Clear DTCs Body Electrical > Navigation System > Clear DTCs

(c) Recheck for DTCs. Try to reproduce the problem symptoms based on the recorded DTCs, and then check if the DTCs are output again.

Chassis > Rear Camera > Trouble Codes Body Electrical > Navigation System > Trouble Codes

Result

Proceed to

No DTCs are output

A

DTCs are output

B

B

GO TO DIAGNOSTIC TROUBLE CODE CHART

A
  1. CHECK FOR Toyota Prius Vehicle CONTROL HISTORY*

HINT:

Refer to Vehicle Control History.

Click here

(a) Check for vehicle control history and note any codes that are output.

Chassis > Rear Camera > Utility

Toyota Prius Vehicle Control History (RoB)

Result

Proceed to

No vehicle control history is output

A

Toyota Prius Vehicle control history is output

B

B

GO TO VEHICLE CONTROL HISTORY

A
  1. PROBLEM SYMPTOMS TABLE

(a) Refer to Problem Symptoms Table.

Click here

Result

Proceed to

Fault is not listed in Problem Symptoms Table

A

Fault is listed in Problem Symptoms Table

B

B

GO TO STEP 10

A
  1. OVERALL ANALYSIS AND TROUBLESHOOTING*

(a) Diagnosis System

Click here

(b) Terminals of ECU

Click here

(c) Data List / Active Test

Click here

NEXT
  1. ADJUST, REPAIR OR REPLACE

NEXT
  1. CONFIRMATION TEST

NEXT

END

Customize Parameters

CUSTOMIZE PARAMETERS

CUSTOMIZE PARKING ASSIST MONITOR SYSTEM

(a) Customize using multi-display.

NOTICE:

  • When the customer requests a change in a function, first make sure that the function can be customized.
  • Be sure to make a note of the current settings before customizing.
  • When troubleshooting a function, first make sure that the function is set to the default setting.
RCD

Display

Measurement Item

Default

Setting

ECU

RCD

Switches the rear camera detection function on and off.

ON

ON or OFF

Rear television camera assembly

Calibration

CALIBRATION

ADJUST PARKING ASSIST MONITOR SYSTEM

(a) The parking assist monitor system can be adjusted using diagnostic mode.

(b) If the following operations are performed, it is necessary to perform adjustments and checks using diagnostic mode.

Part Name

Operation

Adjustment Item

Proceed to

Suspension, tires, etc.

Replacement (The Toyota Prius vehicle height changes due to suspension or tire replacement)

Rear television camera assembly optical axis (Back camera position setting)

Procedure 2

Rear television camera assembly

Replacement

Parking assist monitor system initialization

Procedure 1

Removal and installation of the rear television camera assembly etc. (Installation angle of the rear television camera assembly changes due to removal and installation)

Rear television camera assembly optical axis (Back camera position setting)

Procedure 2

HINT:

The adjustment values stored while performing parking assist monitor system calibration are stored in the rear television camera assembly.

PARKING ASSIST MONITOR SYSTEM INITIALIZATION (PROCEDURE 1)

HINT:

  • Be sure to check for DTCs before performing this procedure.
  • Illustrations may differ from the actual Toyota Prius vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

(a) Preparation for adjustment

(1) Park the vehicle with the steering wheel centered.

(2) Set a target bar behind the Toyota Prius vehicle for optical axis adjustment of the rear television camera assembly (back camera position setting).

HINT:

Create a target bar for adjustment only when adjusting the optical axis of the rear television camera assembly.

*a

Toyota Prius Vehicle Center

*b

Vehicle

*c

Front

*d

Front Wheel Axis

*e

Toyota Prius Vehicle End

*f

Target Bar for Back Camera Adjustment

*g

2000 mm (6.56 ft.)

*h

A

*i

B

Dimension (w/o Rear Camera Detection Function):

A

B

1060 mm (3.48 ft.)

4680 mm (15.35 ft.)

Dimension (w/ Rear Camera Detection Function):

A

B

1600 mm (5.25 ft.)

5220 mm (17.12 ft.)

HINT:

  • Set a piece of tape on the ground as the target bar for adjustment. Its width and length should be 20 to 30 mm (0.787 to 1.180 in.) and 1995 to 2005 mm (6.544 to 6.576 ft.), respectively. Check the color on the radio and display receiver assembly and choose a tape color which can be easily seen.
  • Before parking the Toyota Prius vehicle, be sure to move the vehicle forward and in reverse to check that the tires are facing straight ahead with the steering wheel centered.
  • Check that the back door is fully closed.

(b) Start diagnostic mode.

Click here

NOTICE:

The following must be carried out with start the hybrid control system. Apply the parking brake, depress the brake pedal, check that the shift position is in P, and ensure that the Toyota Prius vehicle is not moving.

(1) Select "Function Check/Setting" on the "Service Menu" screen.

(2) Select "Camera Setting" on the "Function Check/Setting I" screen.

NOTICE:

If the "Camera Setting" selection screen is not displayed, turn the ignition switch off and enter the diagnosis screen after turning the ignition switch to ON once again.

(3) Select "Next" on the "Signal Check (*)" screen.

HINT:

  • When "CHK" (red) is displayed for any items on the "Signal Check (*)" screen, selecting "Next" will not change the screen to the "Steering Angle Setting D (*)" screen.
  • When "CHK" (red) is displayed for any items on the "Signal Check (*)" screen, perform inspections using the "Signal Check (*)" screen.

    Click here

(c) Back Camera Position Setting (Both Ends of Target Bar)

*a

Target Bar for Back Camera Position Setting

HINT:

  • When the back door is open, "You can not calibrate the camera when the door is open. Please close the door" message will be displayed and it will not be possible to perform back camera position setting.
  • Even when the back door is closed and "You can not calibrate the camera when the door is open. Please close the door." is displayed, refer to Problem Symptoms Table and check the cause of the malfunction.

    Click here

(1) Perform vertical and horizontal position adjustment.

  • Move circle A left, right, up and down by selecting buttons C, D, E and F so that the left end of the target bar for back camera position setting is positioned within the center of circle A (center of the inner red circle).

(2) Perform roll angle adjustment.

  • Rotate bar B by selecting buttons G or H so that bar B becomes parallel to target bar for back camera position setting.

(3) Select "Next" on the "Back Camera Position Setting D (*)" screen.

(d) Back Camera Position Setting (Upper Left Corner of Target Bar) (w/ Rear Camera Detection Function)

*a

Target Bar for Back Camera Position Setting

HINT:

  • When the back door is open, the "You can not calibrate the camera when the door is open. Please close the door." message will be displayed and camera position setting will not be possible.
  • If the "You can not calibrate the camera when the door is open. Please close the door." message is displayed even when the back door is closed, perform inspections according to Problem Symptoms Table (When adjusting the camera optical axis, "You can not calibrate the camera when the door is open. Please close the door." is displayed even after the back door has been closed).

    Click here

(1) Perform camera optical axis adjustment (high accuracy adjustment).

  • Move the adjustment mark (A) using the left, right, down and up buttons (B), (C), (D) and (E) to align the corner of the mark (A) with the upper left corner of the target bar.

    Standard:

    The outer corner of the mark (A) is aligned with the upper left corner of the target bar.

    *a

    Too Far Inside

    *b

    Inner Corner Contacting

    *c

    Too Far Outside

    -

    -

(2) Select "Next" on the "Back Camera Position Setting D (*) L_TOP" screen.

(e) Back Camera Position Setting (Lower Left Corner of Target Bar) (w/ Rear Camera Detection Function)

*a

Target Bar for Back Camera Position Setting

HINT:

  • When the back door is open, the "You can not calibrate the camera when the door is open. Please close the door." message will be displayed and camera position setting will not be possible.
  • If the "You can not calibrate the camera when the door is open. Please close the door." message is displayed even when the back door is closed, perform inspections according to Problem Symptoms Table (When adjusting the camera optical axis, "You can not calibrate the camera when the door is open. Please close the door." is displayed even after the back door has been closed).

    Click here

(1) Perform camera optical axis adjustment (high accuracy adjustment).

  • Move the mark (A) using the left, right, down and up buttons (B), (C), (D) and (E) to align the outer corner of the mark (A) with the lower left corner of the target bar.

    Standard:

    The outer corner of the mark (A) is aligned with the lower left corner of the target bar.

    *a

    Too Far Inside

    *b

    Inner Corner Contacting

    *c

    Too Far Outside

    -

    -

(2) Select "Next" on the "Back Camera Position Setting D (*) L_BTM" screen.

(f) Back Camera Position Setting (Upper Right Corner of Target Bar) (w/ Rear Camera Detection Function)

*a

Target Bar for Back Camera Position Setting

HINT:

  • When the back door is open, the "You can not calibrate the camera when the door is open. Please close the door." message will be displayed and camera position setting will not be possible.
  • If the "You can not calibrate the camera when the door is open. Please close the door." message is displayed even when the back door is closed, perform inspections according to Problem Symptoms Table (When adjusting the camera optical axis, "You can not calibrate the camera when the door is open. Please close the door." is displayed even after the back door has been closed).

    Click here

(1) Perform camera optical axis adjustment (high accuracy adjustment).

  • Move the mark (A) using the left, right, down and up buttons (B), (C), (D) and (E) to align the outer corner of the mark (A) with the upper right corner of the target bar.

    Standard:

    The outer corner of the mark (A) is aligned with the upper right corner of the target bar.

    *a

    Too Far Inside

    *b

    Inner Corner Contacting

    *c

    Too Far Outside

    -

    -

(2) Select "Next" on the "Back Camera Position Setting D (*) R_TOP" screen.

(g) Back Camera Position Setting (Lower Right Corner of Target Bar) (w/ Rear Camera Detection Function)

*a

Target Bar for Back Camera Position Setting

HINT:

  • When the back door is open, the "You can not calibrate the camera when the door is open. Please close the door." message will be displayed and camera position setting will not be possible.
  • If the "You can not calibrate the camera when the door is open. Please close the door." message is displayed even when the back door is closed, perform inspections according to Problem Symptoms Table (When adjusting the camera optical axis, "You can not calibrate the camera when the door is open. Please close the door." is displayed even after the back door has been closed).

    Click here

(1) Perform camera optical axis adjustment (high accuracy adjustment).

  • Move the mark (A) using the left, right, down and up buttons (B), (C), (D) and (E) to align the outer corner of the mark (A) with the lower right corner of the target bar.

    Standard:

    The outer corner of the mark (A) is aligned with the lower right corner of the target bar.

    *a

    Too Far Inside

    *b

    Inner Corner Contacting

    *c

    Too Far Outside

    -

    -

(2) Select "Next" on the "Back Camera Position Setting D (*) R_BTM" screen.

(h) Back Verify Mode

(1) Check that A and the target adjustment bar are overlapping.

  • If A and the target adjustment bar are not aligned even if the tires are aligned straight ahead, perform the back camera position setting operation.

(2) Select "OK" to return to the "Function Check/Setting I" screen and complete the adjustment.

HINT:

  • The update is not completed until "OK" is selected.
  • When "OK" is selected, a beep will sound to confirm that the adjustment values have been stored.
  • The adjustment values are not stored until the beep has sounded.

(i) Finish diagnostic mode.

Click here

BACK CAMERA POSITION SETTING (PROCEDURE 2)

HINT:

  • Be sure to check for DTCs before performing this procedure.
  • Illustrations may differ from the actual Toyota Prius vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

Dimension (w/o Rear Camera Detection Function):

A

B

1060 mm (3.48 ft.)

4680 mm (15.35 ft.)

Dimension (w/ Rear Camera Detection Function):

A

B

1600 mm (5.25 ft.)

5220 mm (17.12 ft.)

*a

Toyota Prius Vehicle Center

*b

Vehicle

*c

Front

*d

Front Wheel Axis

*e

Toyota Prius Vehicle End

*f

Target Bar for Back Camera Adjustment

*g

2000 mm (6.56 ft.)

*h

A

*i

B

(a) Preparation for adjustment

(1) Park the Toyota Prius vehicle with the steering wheel centered.

(2) Set a target bar behind the vehicle for optical axis adjustment of the rear television camera assembly (back camera position setting).

HINT:

Create a target bar for adjustment only when adjusting the optical axis of the rear television camera assembly.

HINT:

  • Set a piece of tape on the ground as the target bar for adjustment. Its width and length should be 20 to 30 mm (0.787 to 1.180 in.) and 1995 to 2005 mm (6.544 to 6.576 ft.), respectively. Check the color on the radio and display receiver assembly and choose a tape color which can be easily seen.
  • Before parking the Toyota Prius vehicle, be sure to move the vehicle forward and in reverse to check that the tires are facing straight ahead with the steering wheel centered.
  • Check that the back door is fully closed.

(b) Start diagnostic mode.

Click here

NOTICE:

The following must be carried out with start the hybrid control system. Apply the parking brake, depress the brake pedal, check that the shift position is in P, and ensure that the Toyota Prius vehicle is not moving.

(1) Select "Function Check/Setting" on the "Service Menu" screen.

(2) Select "Camera Setting" on the "Function Check/Setting I" screen.

NOTICE:

If the "Camera Setting" selection screen is not displayed, turn the ignition switch off and enter the diagnosis screen after turning the ignition switch to ON once again.

(3) Select "Back Camera Setting" on the "Mode Setting (*)" screen.

HINT:

To select a grayed out item, select and hold the item for 2 seconds or more.

(4) Select "Next" on the "Signal Check (*)" screen.

HINT:

  • When "CHK" (red) is displayed for any items on the "Signal Check (*)" screen, selecting "Next" will not change the screen to the "Back Camera Position Setting D (*)" screen.
  • When "CHK" (red) is displayed for any items on the "Signal Check (*)" screen, perform inspections using the "Signal Check (*)" screen.

    Click here

(c) Back Camera Position Setting (Both Ends of Target Bar)

*a

Target Bar for Back Camera Position Setting

HINT:

  • When the back door is open, "You can not calibrate the camera when the door is open. Please close the door." message will be displayed and it will not be possible to perform back camera position setting.
  • Even when the back door is closed and "You can not calibrate the camera when the door is open. Please close the door." is displayed, refer to Problem Symptoms Table and check the cause of the malfunction.

    Click here

(1) Perform vertical and horizontal position adjustment.

  • Move circle A left, right, up and down by selecting buttons C, D, E and F so that the left end of the target bar for back camera position setting is positioned within the center of circle A (center of the inner red circle).

(2) Perform roll angle adjustment.

  • Rotate bar B by selecting buttons G or H so that bar B becomes parallel to the target bar for back camera position setting.

(3) Select "Next" on the "Back Camera Position Setting D (*)" screen.

(d) Back Camera Position Setting (Upper Left Corner of Target Bar) (w/ Rear Camera Detection Function)

*a

Target Bar for Back Camera Position Setting

HINT:

  • When the back door is open, the "You can not calibrate the camera when the door is open. Please close the door." message will be displayed and camera position setting will not be possible.
  • If the "You can not calibrate the camera when the door is open. Please close the door." message is displayed even when the back door is closed, perform inspections according to Problem Symptoms Table (When adjusting the camera optical axis, "You can not calibrate the camera when the door is open. Please close the door." is displayed even after the back door has been closed).

    Click here

(1) Perform camera optical axis adjustment (high accuracy adjustment).

  • Move the adjustment mark (A) using the left, right, down and up buttons (B), (C), (D) and (E) to align the corner of the mark (A) with the upper left corner of the target bar.

    Standard:

    The outer corner of the mark (A) is aligned with the upper left corner of the target bar.

    *a

    Too Far Inside

    *b

    Inner Corner Contacting

    *c

    Too Far Outside

    -

    -

(2) Select "Next" on the "Back Camera Position Setting D (*) L_TOP" screen.

(e) Back Camera Position Setting (Lower Left Corner of Target Bar) (w/ Rear Camera Detection Function)

*a

Target Bar for Back Camera Position Setting

HINT:

  • When the back door is open, the "You can not calibrate the camera when the door is open. Please close the door." message will be displayed and camera position setting will not be possible.
  • If the "You can not calibrate the camera when the door is open. Please close the door." message is displayed even when the back door is closed, perform inspections according to Problem Symptoms Table (When adjusting the camera optical axis, "You can not calibrate the camera when the door is open. Please close the door." is displayed even after the back door has been closed).

    Click here

(1) Perform camera optical axis adjustment (high accuracy adjustment).

  • Move the mark (A) using the left, right, down and up buttons (B), (C), (D) and (E) to align the outer corner of the mark (A) with the lower left corner of the target bar.

    Standard:

    The outer corner of the mark (A) is aligned with the lower left corner of the target bar.

    *a

    Too Far Inside

    *b

    Inner Corner Contacting

    *c

    Too Far Outside

    -

    -

(2) Select "Next" on the "Back Camera Position Setting D (*) L_BTM" screen.

(f) Back Camera Position Setting (Upper Right Corner of Target Bar) (w/ Rear Camera Detection Function)

*a

Target Bar for Back Camera Position Setting

HINT:

  • When the back door is open, the "You can not calibrate the camera when the door is open. Please close the door." message will be displayed and camera position setting will not be possible.
  • If the "You can not calibrate the camera when the door is open. Please close the door." message is displayed even when the back door is closed, perform inspections according to Problem Symptoms Table (When adjusting the camera optical axis, "You can not calibrate the camera when the door is open. Please close the door." is displayed even after the back door has been closed).

    Click here

(1) Perform camera optical axis adjustment (high accuracy adjustment).

  • Move the mark (A) using the left, right, down and up buttons (B), (C), (D) and (E) to align the outer corner of the mark (A) with the upper right corner of the target bar.

    Standard:

    The outer corner of the mark (A) is aligned with the upper right corner of the target bar.

    *a

    Too Far Inside

    *b

    Inner Corner Contacting

    *c

    Too Far Outside

    -

    -

(2) Select "Next" on the "Back Camera Position Setting D (*) R_TOP" screen.

*a

Target Bar for Back Camera Position Setting

(g) Back Camera Position Setting (Lower Right Corner of Target Bar) (w/ Rear Camera Detection Function)

HINT:

  • When the back door is open, the "You can not calibrate the camera when the door is open. Please close the door." message will be displayed and camera position setting will not be possible.
  • If the "You can not calibrate the camera when the door is open. Please close the door." message is displayed even when the back door is closed, perform inspections according to Problem Symptoms Table (When adjusting the camera optical axis, "You can not calibrate the camera when the door is open. Please close the door." is displayed even after the back door has been closed).

    Click here

(1) Perform camera optical axis adjustment (high accuracy adjustment).

  • Move the mark (A) using the left, right, down and up buttons (B), (C), (D) and (E) to align the outer corner of the mark (A) with the lower right corner of the target bar.

    Standard:

    The outer corner of the mark (A) is aligned with the lower right corner of the target bar.

    *a

    Too Far Inside

    *b

    Inner Corner Contacting

    *c

    Too Far Outside

    -

    -

(2) Select "Next" on the "Back Camera Position Setting D (*) R_BTM" screen.

(h) Back Verify Mode

(1) Check that A and the target adjustment bar are overlapping.

  • If A and the target adjustment bar are not aligned even if the tires are aligned straight ahead, perform the back camera position setting operation.

(2) Select "OK" to return to the "Mode Setting (*)" screen and complete the adjustment.

HINT:

  • The update is not completed until "OK" is selected.
  • When "OK" is selected, a beep will sound to confirm that the adjustment values have been stored.
  • The adjustment values are not stored until the beep has sounded.

(i) Finish diagnostic mode.

Click here

Utility

UTILITY

HINT:

  • With "All Readiness", you can check whether or not the DTC judgment has been completed by using the GTS.
  • You should check "All Readiness" after simulating malfunction symptoms or for validation after finishing repairs.

ALL READINESS

(a) Clear the DTCs even if no DTCs are stored.

Chassis > Rear Camera > Clear DTCs

(b) Turn the ignition switch off and wait for 2 minutes or more.

(c) Turn the ignition switch to ON.

(d) Perform the DTC judgment driving pattern to run the DTC judgment.

Chassis > Rear Camera > Utility

All Readiness

(e) Input the DTCs to be confirmed.

(f) Check the DTC judgment result.

GTS Display

Description

If the judgment result shows Incomplete, perform the DTC confirmation driving pattern again.

Normal

  • DTC judgment completed
  • System normal

Abnormal

  • DTC judgment completed
  • System abnormal

Incomplete

  • DTC judgment not completed
  • Perform the driving pattern

CLEAR IMAGE INFORMATION (w/ Rear Camera Detection Function)

HINT:

This utility is used to clear the image information stored in the rear television camera assembly.

(a) Perform "Image Information Clear " according to the display on the GTS.

Chassis > Rear Camera > Utility

Image Information Clear

IMAGE RECORDING SETTING (w/ Rear Camera Detection Function)

HINT:

This utility is used to enable/disable image recording.

(a) Perform "Image Recording Setting" according to the display on the GTS.

Chassis > Rear Camera > Utility

Image Record Setting

Problem Symptoms Table

PROBLEM SYMPTOMS TABLE

NOTICE:

  • The following inspection procedures for the parking assist monitor system are based on the assumption that the audio and visual system is normal. If the audio and visual system has any malfunction, first proceed with troubleshooting of the audio and visual system.
  • Depending on the parts that are replaced or operations that are performed during Toyota Prius vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.

    Click here

  • The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

    Click here

  • After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

    Click here

    HINT:

    When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

    Click here

HINT:

  • Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
  • Inspect the fuses and relays related to this system before inspecting the suspected areas below.
General

Symptom

Suspected Area

Link

When the shift position is in R, an image of the area behind the Toyota Prius vehicle is not displayed (screen is not black)

Vehicle Signal Check Mode (Reverse Signal)

Check that the back-up light illuminates normally (if not, refer to Lighting System [EXT] - Problem Symptoms Table)

Wire harness and connector

-

Check that the hybrid control system is operating normally

-

Rear television camera assembly

Radio and display receiver assembly

When the shift position is in R, an image of the area behind the Toyota Prius vehicle is not displayed (screen is black)

Proceed to "Image from Camera for Parking Assist Monitor is Abnormal"

When the shift position is not in R, an image of the area behind the Toyota Prius vehicle is displayed

Vehicle Signal Check Mode (Reverse Signal)

Check that the back-up light illuminates normally (if not, refer to Lighting System [EXT] - Problem Symptoms Table)

Wire harness and connector

-

Check that the hybrid control system is operating normally

-

Radio and display receiver assembly

When the shift position is in R, an image of the area behind the Toyota Prius vehicle is displayed and then switches to another image

Vehicle Signal Check Mode (Reverse Signal)

Check that the back-up light illuminates normally (if not, refer to Lighting System [EXT] - Problem Symptoms Table)

Wire harness and connector

-

Rear television camera assembly

Display Malfunction

Symptom

Suspected Area

Link

Parking assist monitor display malfunction (distortion of the color/screen) occurs continuously

Proceed to "Image from Camera for Parking Assist Monitor is Abnormal"

Parking assist monitor display malfunction (distortion of the color/screen) occurs temporarily

Check the usage conditions (explain to the customer that the display may be temporarily distorted when the Toyota Prius vehicle is close to an object that transmits radio waves, such as a telecommunication tower, an airport or a truck equipped with a transceiver)

-

Parking Assist Monitor System Malfunction

Symptom

Suspected Area

Link

Estimated course lines are not displayed

Parking assist monitor screen display mode settings (check that estimated course line display mode is selected)

-

Rear television camera assembly

Radio and display receiver assembly

Steering sensor

The Toyota Prius vehicle width guide lines and estimated course lines do not match when the steering wheel is turned to the center position

Check that the rear television camera assembly is correctly installed

Rear television camera assembly

Steering sensor

The guide lines are not displayed even though the back door is closed

Check that the No. 1 luggage compartment light assembly illuminates normally (if not, refer to Lighting System [INT] - Problem Symptoms Table)

Rear television camera assembly

The guide lines remain displayed even though the back door is open

Check that the No. 1 luggage compartment light assembly illuminates normally (if not, refer to Lighting System [INT] - Problem Symptoms Table)

Rear television camera assembly

Guide lines and buttons are not displayed for all parking assist monitor screen display modes.

Proceed to "Luggage Compartment Room Light" in Lighting System (INT)

Back camera position setting (calibration)

Rear television camera assembly

The guide lines and buttons remain displayed even though the back door is open.

Proceed to "Luggage Compartment Room Light" in Lighting System (INT)

Rear television camera assembly

When adjusting the camera optical axis, "You can not calibrate the camera when the door is open. Please close the door." is displayed even after the back door has been closed

Check that the No. 1 luggage compartment light assembly illuminates normally (if not, refer to Lighting System [INT] - Problem Symptoms Table)

Rear television camera assembly

"CHK" message(s) are displayed on the signal check screen

Signal check (diagnosis system)

When an image of the area behind the Toyota Prius vehicle is displayed, the lines are misaligned (the image from the camera is tilted)

Back camera position setting (calibration)

Rear television camera assembly

Others

Symptom

Suspected Area

Link

A switch displayed on the parking assist monitor screen does not respond when pushed, or a switch other than the pushed switch responds.

Proceed to "CHECK TOUCH SWITCH" in Audio and visual system

Rear television camera assembly

Radio and display receiver assembly

A beep sound is not emitted when a switch displayed on the parking assist monitor screen is pushed.

Check the setting on the audio screen (General setting)

-

Proceed to "CHECK TOUCH SWITCH" in Audio and visual system

Rear television camera assembly

Radio and display receiver assembly

The language of the messages displayed on the parking assist monitor screen cannot be changed.

Check the setting on the audio screen (General setting)

-

Rear television camera assembly

Radio and display receiver assembly

The switches displayed on the parking assist monitor screen are grayed out.

Rear television camera assembly

Radio and display receiver assembly

The color of the switches displayed on the parking assist monitor screen are abnormal, or the switches are not dimmed when the headlights are turned on.

Check the setting on the audio screen (Screen adjustment)

-

Proceed to "CHECK TOUCH SWITCH" in Audio and visual system

Rear television camera assembly

Radio and display receiver assembly

Rear Camera Detection Function (w/ Rear Camera Detection Function)

Symptom

Suspected Area

Link

"[Rear Camera Detection icon] System Malfunction Visit Your Dealer " is displayed

Check Toyota Prius vehicle control history

Rear television camera assembly

"[Rear Camera Detection icon] System Stopped See Owner's Manual " is displayed

Rear television camera assembly

"[Rear Camera Detection icon] Parking Assist Unavailable Low Visibility See Owner's Manual" is displayed

Check Toyota Prius vehicle control history

Rear television camera assembly

The indicator does not respond when the mute switch is pushed.

Audio and visual system - Touch switch self check

Rear television camera assembly

Radio and display receiver assembly

When there is a pedestrian in the detection area, no pedestrian is detected.

"Notes for Rear Camera Detection Function" in precaution

Calibration

Check that the meter / gauge system is operating normally

-

Clearance warning ECU assembly

Rear television camera assembly

When there is no pedestrian in the detection area, a pedestrian is detected.

"Notes for Rear Camera Detection Function" in precaution

Calibration

Rear television camera assembly

A pedestrian who is in the absolute no detection area is detected.

Calibration

Rear television camera assembly

A pedestrian is only detected when they are in the absolute detection area.

Calibration

Rear television camera assembly

Terminals Of Ecu

TERMINALS OF ECU

REAR TELEVISION CAMERA ASSEMBLY

*A

w/ Parking Support Brake System

*B

w/o Parking Support Brake System

(a) Disconnect the rear television camera assembly connector.

(b) Measure the voltage on the wire harness side connector according to the value(s) in the table below.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

*1: w/o Parking Support Brake System

*2: w/ Parking Support Brake System

V2-4 (CB ) - V2-3 (CGND)*1

V3-4 (CB ) - V3-3 (CGND)*2

Power source

Ignition switch ACC

6 to 9 V

(c) Measure the resistance on the wire harness side connector according to the value(s) in the table below.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

*1: w/o Parking Support Brake System

*2: w/ Parking Support Brake System

V2-1 (CANH)*1

V3-1 (CANH)*2

CAN communication line

-

-

V2-2 (CANL)*1

V3-2 (CANL)*2

CAN communication line

-

-

V2-3 (CGND) - Body ground*1

V3-3 (CGND) - Body ground*2

Camera ground

Always

Below 1 Ω

V2-5 (CV-) - Body ground*1

V3-5 (CV-) - Body ground*2

Video signal

-

-

V2-6 (CV )*1

V3-6 (CV )*2

Video signal

-

-

V2-7 (SGND) - Body ground*1

V3-7 (SGND) - Body ground*2

Camera ground (shield)

Always

Below 1 Ω

RADIO AND DISPLAY RECEIVER ASSEMBLY

Click here

Diagnosis System

DIAGNOSIS SYSTEM

PARKING ASSIST MONITOR SYSTEM DIAGNOSTIC MODE

(a) In diagnostic mode for the parking assist monitor system, signals received by the radio and display receiver assembly can be checked and the parking assist monitor system can be calibrated, adjusted and checked using the radio and display receiver assembly.

NOTICE:

Depending on the parts that are replaced or operations that are performed during Toyota Prius vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.

Click here

HINT:

The displayed items may differ depending on vehicle specifications.

DIAGNOSIS SCREEN TRANSITION (DURING PARKING ASSIST MONITOR SYSTEM INITIALIZATION) (w/o Rear Camera Detection Function)

DIAGNOSIS SCREEN TRANSITION (AFTER PARKING ASSIST MONITOR SYSTEM INITIALIZATION) (w/o Rear Camera Detection Function)

DIAGNOSIS SCREEN TRANSITION (DURING PARKING ASSIST MONITOR SYSTEM INITIALIZATION) (w/ Rear Camera Detection Function)

DIAGNOSIS SCREEN TRANSITION (AFTER PARKING ASSIST MONITOR SYSTEM INITIALIZATION) (w/ Rear Camera Detection Function)

Toyota Prius Vehicle SIGNAL CHECK

HINT:

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

(a) Start diagnostic mode.

Click here

(b) Select "Function Check/Setting" on the "Service Menu" screen to display the "Function Check/Setting I" screen.

(c) Select "Toyota Prius Vehicle Signal" on the "Function Check/Setting I" screen.

(d) Vehicle Signal Check Mode

(1) When the "Vehicle Signal Check Mode" screen is displayed, check the item displayed for "REV".

Click here

HINT:

  • Only conditions having inputs are displayed.
  • This screen displays Toyota Prius vehicle signals input to the radio and display receiver assembly.

(e) Finish diagnostic mode.

Click here

HINT:

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual Toyota Prius vehicle screen.

SIGNAL CHECK (PARKING ASSIST MONITOR SYSTEM INPUT SIGNALS)

(a) Start diagnostic mode.

Click here

(1) Select "Function Check/Setting" on the "Service Menu" screen to display the "Function Check/Setting I" screen.

(2) Select "Camera Setting" on the "Function Check/Setting I" screen.

NOTICE:

If the "Camera Setting" selection screen is not displayed, turn the ignition switch off and enter the diagnosis screen after turning the ignition switch to ON once again.

HINT:

After "Camera Setting" is selected, the screen transitions differ depending on whether initialization of the parking assist monitor system was performed after the rear television camera assembly was replaced.

Parking Assist Monitor System Initialization

Screen Transition

Not performed

Signal Check (*) screen

Performed

Mode Setting (*) screen

(3) When the screen changes to the "Mode Setting (*)" screen, select "Back Camera Setting" to display the "Signal Check (*)" screen.

HINT:

To select a grayed out item, select and hold the item for 2 seconds or more.

(b) Signal Check

(1) On the "Signal Check (*)" screen, it is possible to inspect the state of signals and check the settings.

Item

Inspection Detail

Note

CAN

CAN communication signal input

When "CHK" (red) is displayed, selecting "Next" will not change the screen to the next screen.

HINT:

  • When "CHK" (red) is displayed, perform inspections based on the result of the following inspections.
  • If performing the adjustment after proceeding to the next screen, confirm that all items display "OK" (blue) before selecting "Next".

(c) CAN inspection

HINT:

If "CHK" (red) is displayed for "CAN", check for DTCs and perform troubleshooting based on the output DTCs.

(d) Finish diagnostic mode.

Click here

CAMERA DETECTION SETTING

HINT:

Illustrations may differ from the actual Toyota Prius vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

(a) Start diagnostic mode.

Click here

(1) Select "Function Check/Setting" on the "Service Menu" screen to display the "Function Check/Setting I" screen.

(2) Select "Camera Setting" on the "Function Check/Setting I" screen.

(b) Camera Detection Setting

(1) Select "Camera Detection Setting" on the "Mode Setting " screen.

(2) Select ON or OFF on the "Camera Detection Setting" screen as necessary.

HINT:

After selecting ON or OFF, return to the "Mode Setting" screen by selecting "OK" or "Back".

(c) Finish diagnostic mode.

Click here

VIDEO DEVICE CONNECTION CHECK

Click here

CALIBRATION WHEN SERVICING Toyota Prius Vehicle

NOTICE:

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.

Click here

Freeze Frame Data

FREEZE FRAME DATA

HINT:

  • Freeze frame data is stored at the time when DTCs are detected.
  • When freeze frame data at the time it is stored that a DTC is detected, data is not updated or cleared until the stored data is cleared (Clear DTCs).

CHECK FREEZE FRAME DATA

(a) According to the display on the GTS, display the freeze frame data for the selected DTC.

Chassis > Rear Camera

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Total Distance Traveled

Total distance traveled

1 to 999999

Same as actual total distance traveled

For the unit, refer to "Total Distance Traveled - Unit"

Total Distance Traveled - Unit

Total distance traveled unit

km or mile

km: km

mile: mile

-

Steering Angle

Steering angle

-3276.8 to 3276.7°

Steering left: Changes positively continuously

Steering right: Changes negative continuously

-

Toyota Prius Vehicle Speed

Vehicle speed

Vehicle speed

Equivalent to actual vehicle speed

-

Toyota Prius Vehicle Height Sensor Value (Rear)

Vehicle height sensor value (rear)

Calculate the current vehicle height sensor value

0 to 320 v

-

FR Wheel Toyota Prius Vehicle Height Sensor Value

FR wheel vehicle height sensor value

Calculate the current vehicle height sensor value

0 to 255 mm

-

FL Wheel Toyota Prius Vehicle Height Sensor Value

FL wheel vehicle height sensor value

Calculate the current vehicle height sensor value

0 to 255 mm

-

RR Wheel Toyota Prius Vehicle Height Sensor Value

RR wheel vehicle height sensor value

Calculate the current vehicle height sensor value

0 to 255 mm

-

RL Wheel Toyota Prius Vehicle Height Sensor Value

RL wheel vehicle height sensor value

Calculate the current vehicle height sensor value

0 to 255 mm

-

EPS Steering Angle Value

EPS steering angle value

-3276.8 to 3276.7°

Steering left: Changes positively continuously

Steering right: Changes negative continuously

-

Target Steering Angle Value (SBW)

Target steering angle value (SBW)

-3276.8 to 3276.7°

Steering left: Changes positively continuously

Steering right: Changes negative continuously

-

CLEAR FREEZE FRAME DATA

NOTICE:

Clearing the DTCs will also clear the freeze frame data.

(a) Clear the DTCs and freeze frame data.

Chassis > Rear Camera > Clear DTCs

Fail-safe Chart

FAIL-SAFE CHART

FAIL-SAFE FUNCTION

(a) If a malfunction occurs in part of the rear camera detection function, "[Rear Camera Detection icon] System Malfunction Visit Your Dealer" or "[Rear Camera Detection icon] System Stopped See Owner's Manual" is displayed on the multi-information display in the combination meter assembly, the integrated indicator illuminates, and control of rear camera detection functions related to the malfunction are canceled.

(b) If the rear television camera assembly judges that pedestrian detection is not possible such as when dirt is on the rear television camera assembly or during inclement weather such as snowfall, etc., "[Rear Camera Detection icon] Parking Assist Unavailable Low Visibility See Owner's Manual" is displayed on the multi-information display in the combination meter assembly, the integrated indicator illuminates, and control of all functions are cancelled. Furthermore, "[Rear Camera Detection icon] Parking Assist Unavailable Low Visibility See Owner's Manual" is displayed temporary and after it is cleared, the warning will be continued by illuminating the integrated indicator. Also, when pedestrian detection becomes possible, the integrated indicator turns off and normal control resumes.

Data List / Active Test

DATA LIST / ACTIVE TEST

DATA LIST

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

(a) Read the Data List according to the display on the GTS.

Chassis > Rear Camera

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Total Distance Traveled

Total distance traveled

1 to 999999

Same as actual total distance traveled

For the unit, refer to "Total Distance Traveled - Unit"

Total Distance Traveled - Unit

Total distance traveled unit

km or mile

km: km

mile: mile

-

Steering Angle

Steering angle

-3276.8 to 3276.7°

Steering left: Changes positively continuously

Steering right: Changes negative continuously

-

Toyota Prius Vehicle Speed

Vehicle speed

Vehicle speed

Equivalent to actual vehicle speed

-

Toyota Prius Vehicle Height Sensor Value (Rear)

Calculate the current vehicle height sensor value

Calculate the current vehicle height sensor value

0 to 320 v

-

FR Wheel Toyota Prius Vehicle Height Sensor Value

Calculate the current vehicle height sensor value

Calculate the current vehicle height sensor value

0 to 255 mm

-

FL Wheel Toyota Prius Vehicle Height Sensor Value

Calculate the current vehicle height sensor value

Calculate the current vehicle height sensor value

0 to 255 mm

-

RR Wheel Toyota Prius Vehicle Height Sensor Value

Calculate the current vehicle height sensor value

Calculate the current vehicle height sensor value

0 to 255 mm

-

RL Wheel Toyota Prius Vehicle Height Sensor Value

Calculate the current vehicle height sensor value

Calculate the current vehicle height sensor value

0 to 255 mm

-

EPS Steering Angle Value

Calculate the current EPS rudder angle value

-3276.8 to 3276.7°

Steering left: Changes positively continuously

Steering right: Changes negative continuously

-

Target Steering Angle Value (SBW)

Calculate the current target steering angle value

-3276.8 to 3276.7°

Steering left: Changes positively continuously

Steering right: Changes negative continuously

-

Diagnostic Trouble Code Chart

DIAGNOSTIC TROUBLE CODE CHART

Parking Assist Monitor System

DTC No.

Detection Item

DTC Output from

Priority

Link

C161704

Camera Malfunction System Internal Failure

Rear Camera

A

C161B04

Rear Camera Control Module System Internal Failure

Rear Camera

A

U012687

Lost Communication with Steering Angle Sensor Module Missing Message

Rear Camera

B

U012987

Lost Communication with Brake System Control Module "A" Missing Message

Rear Camera

B

U013187

Lost Communication with Power Steering Control Module Missing Message

Rear Camera

B

U014087

Lost Communication with Body Control Module Missing Message

Rear Camera

B

U015587

Lost Communication with Instrument Panel Cluster (IPC) Control Module Missing Message

Rear Camera

B

U016387

Lost Communication with Navigation Control Module Missing Message

Rear Camera

B

U029387

Lost Communication with Hybrid/EV Powertrain Control Module Missing Message

Rear Camera

B

U111087

Lost Communication with Clearance Sonar Module Missing Message

Rear Camera

B

VEHICLE CONTROL HISTORY (RoB)

VEHICLE CONTROL HISTORY (RoB)

NOTICE:

When checking the vehicle control history, first store the output history and then check the history.

HINT:

Depending on the specifications of the vehicle, some items may not be displayed.

CHECK VEHICLE CONTROL HISTORY

(a) Read the Toyota Prius Vehicle Control History (RoB) according to the display on the GTS.

Chassis > Rear Camera > Utility

Vehicle Control History (RoB)

Toyota Prius Vehicle Control History Item

Code

Tester Display

Measurement Item

Notes

Toyota Prius Vehicle Control History Data

X2001

Steering Angle Sensor Malfunction

Outputs the malfunction judgment result for the steering angle sensor

The following data items are stored

  • Total Distance Traveled
  • Total Distance Traveled - Unit
  • Steering Angle Sensor Internal Malfunction
  • VGRS System Invalid
  • VGRS Failure
  • EPS Fail
  • EPS Invalid
  • Target Steering Angle Value (EPS)
  • Steering Angle Actual Value (DRS)
  • DRS Fail

X2003

Brake Control System Malfunction

Outputs the malfunction judgment result for the electronically controlled brake system

The following data items are stored

  • Total Distance Traveled
  • Total Distance Traveled - Unit
  • Toyota Prius Vehicle Speed Signal (SP1) Invalid
  • Wheel Speed Sensor Backward Judgement Malfunction
  • FR Wheel Rotatory Direction Invalid
  • FL Wheel Rotatory Direction Invalid
  • RR Wheel Rotatory Direction Invalid
  • RL Wheel Rotatory Direction Invalid
  • Wheel Speed Sensor Backward Judgement Function Availability
  • FR Wheel Speed Sensor Invalid
  • FL Wheel Speed Sensor Invalid
  • RR Wheel Speed Sensor Invalid
  • RL Wheel Speed Sensor Invalid

X20BE

Rear Camera Detection Unavailable (Dirty)

The rear camera detection function is temporarily not able to operate due to the rear camera being temporarily dirty, malfunctioning, etc.

Remove dirt from the rear camera.

The following data items are stored

  • Total Distance Traveled
  • Total Distance Traveled - Unit
  • Camera Washer Function Operation Times
  • Dirty Detection Times

X2130

PKSB Operation History (Rear Camera)

Operation history for the parking support brake (rear camera)

-

The following data items are stored

  • Total Distance Traveled
  • Total Distance Traveled - Unit
  • Steering Angle
  • Toyota Prius Vehicle Height Control Sensor Value (Rear)
  • Vehicle Height Control Sensor Value (FR wheel)
  • Vehicle Height Control Sensor Value (FL wheel)
  • Vehicle Height Control Sensor Value (RR wheel)
  • Vehicle Height Control Sensor Value (RL wheel)

X2132

Rear Camera Detection Unavailable (Other)

The rear camera detection function is temporarily not able to operate due to the rear camera being temporarily dirty, malfunctioning, etc.

Remove dirt from the rear camera.

The following data items are stored

  • Total Distance Traveled
  • Total Distance Traveled - Unit

X2133

Rear Camera Detection Unavailable (Dirty (Dirt Detect Timing Information))

The rear camera detection function is temporarily not able to operate due to the rear camera being temporarily dirty, malfunctioning, etc.

Remove dirt from the rear camera.

The following data items are stored

  • Total Distance Traveled
  • Total Distance Traveled - Unit
  • Steering Angle
  • Camera Washer Function Operation Times
  • Dirty Detection Times

X2195

Headlight Control Module Malfunction

Outputs the abnormality judgment result of the headlamp control system

The following data items are stored

  • Total Distance Traveled
  • Total Distance Traveled - Unit
  • Toyota Prius Vehicle Height Control Sensor Data Valid
  • Vehicle Height Control Sensor Data Malfunction

X2601

Software Inconsistency with ENG/HEV/EV Control Module

Detects a mismatch between the setting value stored in nonvolatile memory and the HEV/ENG signal judgment value received from CAN

The following data items are stored

  • Total Distance Traveled
  • Total Distance Traveled - Unit

X2603

Software Inconsistency with Body Control Module

Detects a mismatch between the setting value stored in nonvolatile memory and the BDB signal judgment value received from CAN

-

The following data items are stored

  • Total Distance Traveled
  • Total Distance Traveled - Unit

X261F

Software Inconsistency with Power Steering Control Module

Detects a mismatch between the setting value stored in nonvolatile memory and the EPS system signal judgment value received from CAN

The following data items are stored

  • Total Distance Traveled
  • Total Distance Traveled - Unit

X263C

Rear Camera Optical Axis Alignment Not Performed

Rear television camera assembly beam axis alignment has not been performed

  1. If Rob is output again, replace the rear television camera assembly.

The following data items are stored

  • Total Distance Traveled
  • Total Distance Traveled - Unit

X2657

Software Inconsistency with Headlamp Control Module "A"

Output when a mismatch between the set value stored in the non-volatile memory and the headlamp control system (main) signal judgment value received from CAN is detected.

The following data items are stored

  • Total Distance Traveled
  • Total Distance Traveled - Unit

X284E

Rear Camera Wash Function Operation History

Operation history for the rear camera wash function

-

The following data items are stored

  • Total Distance Traveled
  • Total Distance Traveled - Unit
  • Steering Angle
  • Camera Washer Function Operation Times
  • Dirty Detection Times

X2856

Information of Detection High Acceleration (Rear Camera)

History of Toyota Prius vehicle acceleration of a certain value or more being detected

-

The following data items are stored

  • Total Distance Traveled
  • Total Distance Traveled - Unit
  • Steering Angle
  • Toyota Prius Vehicle Height Control Sensor Value (Rear)
  • Vehicle Height Control Sensor Value (FR wheel)
  • Vehicle Height Control Sensor Value (FL wheel)
  • Vehicle Height Control Sensor Value (RR wheel)
  • Vehicle Height Control Sensor Value (RL wheel)

CLEAR Toyota Prius Vehicle CONTROL HISTORY

(a) According to the display on the GTS, clear the Vehicle Control History (RoB).

NOTICE:

When the vehicle control history is cleared, all the stored history items are cleared.

Chassis > Rear Camera > Utility

Toyota Prius Vehicle Control History (RoB)

CHECK VEHICLE CONTROL HISTORY (SRS AIRBAG SYSTEM)

HINT:

Some of the control history can be checked from "Vehicle Control History".

Click here

Camera Malfunction System Internal Failure (C161704,C161B04)

DESCRIPTION

This DTC is stored if the rear television camera assembly judges that there is an internal malfunction as a result of its self check.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

DTC Output from

Priority

C161704

Camera Malfunction System Internal Failure

ECU internal malfunction

Rear television camera assembly

Rear Camera

A

C161B04

Rear Camera Control Module System Internal Failure

ECU internal malfunction

Rear television camera assembly

Rear Camera

A

NOTICE:

Depending on the parts that are replaced or operations that are performed during Toyota Prius vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.

Click here

PROCEDURE

  1. REPLACE TELEVISION CAMERA ASSEMBLY RR

(a) Replace the rear television camera assembly with a new one.

HINT:

Click here

NEXT

END

Lost Communication with Steering Angle Sensor Module Missing Message (U012687,U012987,U013187,U014087,U015587,U016387,U029387,U111087)

DESCRIPTION

These DTCs are stored if there is a malfunction in the CAN communication system connected to the rear television camera assembly.

HINT:

If CAN communication system DTCs are stored, they may also be stored in other systems.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

DTC Output from

Priority

U012687

Lost Communication with Steering Angle Sensor Module Missing Message

Lost communication with steering sensor

CAN communication system

Rear Camera

B

U012987

Lost Communication with Brake System Control Module "A" Missing Message

Lost communication with No. 2 skid control ECU (brake actuator assembly)

CAN communication system

Rear Camera

B

U013187

Lost Communication with Power Steering Control Module Missing Message

Lost communication with power steering ECU

CAN communication system

Rear Camera

B

U014087

Lost Communication with Body Control Module Missing Message

Lost communication with main body ECU (multiplex network body ECU)

CAN communication system

Rear Camera

B

U015587

Lost Communication with Instrument Panel Cluster (IPC) Control Module Missing Message

Lost communication with combination meter assembly

CAN communication system

Rear Camera

B

U016387

Lost Communication with Navigation Control Module Missing Message

Lost communication with radio and display receiver assembly

CAN communication system

Rear Camera

B

U029387

Lost Communication with Hybrid/EV Powertrain Control Module Missing Message

Lost communication with hybrid Toyota Prius vehicle control ECU

CAN communication system

Rear Camera

B

U111087

Lost Communication with Clearance Sonar Module Missing Message

Lost communication with clearance warning ECU assembly

CAN communication system

Rear Camera

B

PROCEDURE

  1. CLEAR DTC

(a) Clear the DTCs.

Chassis > Rear Camera > Clear DTCs
NEXT
  1. CHECK FOR DTC

(a) Check for DTCs.

Chassis > Rear Camera > Trouble Codes

HINT:

  • If CAN communication system DTCs are stored, they may also be stored in other systems.
  • If the CAN communication system has been inspected and repaired in other systems, the DTCs will not be output when rechecking for DTCs.
  • If these DTCs are output frequently, duplicate the conditions that cause the problem symptoms and perform the inspection again, even though the DTC was not output when rechecking for DTCs.

    Click here

Result

Proceed to

DTCs are not output

A

DTCs are output

B

A

USE SIMULATION METHOD TO CHECK

B

GO TO CAN COMMUNICATION SYSTEM

Image from Camera for Parking Assist Monitor is Abnormal

DESCRIPTION

The display signal from the rear television camera assembly is transmitted to the display.

WIRING DIAGRAM

NOTICE:

Depending on the parts that are replaced or operations that are performed during Toyota Prius vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.

Click here

HINT:

Images may be unclear even in normal conditions if:

  • Electrical devices are used in the cabin (noise may occur in the image).
  • Accessories that generate radio waves have been installed (noise may occur in the image).
  • The display of radio and display receiver assembly is cold (the image immediately after turning the ignition switch to ON may be blurred or darker than normal).
  • The camera lens is dirty with snow, mud, etc.
  • A strong beam of light, such as a sunbeam or headlight, hits the camera.
  • It is too dark around the camera (at night, etc.).
  • The ambient temperature around the camera is either too high or too low.
  • The Toyota Prius vehicle is tilted at a steep angle.
  • The television camera assembly lens is scratched.
  • The television camera assembly lens has drops of water on it or the humidity is high.
  • When the camera is used under fluorescent lights, sodium lights, mercury lights, etc., the lights and the illuminated area may appear to flicker.

PROCEDURE

  1. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)

(a) Disconnect the K126 radio and display receiver assembly connector.

(b) Disconnect the V2*1 or V3*2 rear television camera assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(K126,V2,V3) Click Connector(K126) Click Connector(V2) Click Connector(V3)

Tester Connection

Condition

Specified Condition

K126-2 (CB ) - V2-4 (CB )*1 or V3-4 (CB )*2

Always

Below 1 Ω

K126-3 (CV ) - V2-6 (CV )*1 or V3-6 (CV )*2

Always

Below 1 Ω

K126-1 (CGND) - V2-3 (CGND)*1 or V3-3 (CGND)*2

Always

Below 1 Ω

K126-4 (CV-) - V2-5 (CV-)*1 or V3-5 (CV-)*2

Always

Below 1 Ω

K126-5 (SGND) - V2-7 (SGND)*1 or V3-7 (SGND)*2

Always

Below 1 Ω

K126-2 (CB ), V2-4 (CB )*1 or V3-4 (CB )*2 - Body ground

Always

10 kΩ or higher

K126-3 (CV ), V2-6 (CV )*1 or V3-6 (CV )*2 - Body ground

Always

10 kΩ or higher

K126-1 (CGND), V2-3 (CGND)*1 or V3-3 (CGND)*2 - Body ground

Always

10 kΩ or higher

K126-4 (CV-), V2-5 (CV-)*1 or V3-5 (CV-)*2 - Body ground

Always

10 kΩ or higher

K126-5 (SGND), V2-7 (SGND)*1 or V3-7 (SGND)*2 - Body ground

Always

10 kΩ or higher

  • *1: w/o Parking Support Brake System
  • *2: w/ Parking Support Brake System
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

(a) Disconnect the V2*1 or V3*2 rear television camera assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(V2,V3) Click Connector(V2) Click Connector(V3)

Tester Connection

Condition

Specified Condition

V2-3 (CGND)*1 or V3-3 (CGND)*2 - Body ground

Always

Below 1 Ω

V2-5 (CV-)*1 or V3-5 (CV-)*2 - Body ground

Always

Below 1 Ω

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Click Location & Routing(V2,V3) Click Connector(V2) Click Connector(V3)

Tester Connection

Switch Condition

Specified Condition

V2-4 (CB )*1 or V3-4 (CB )*2 - Body ground

Ignition switch ACC

6 to 9 V

Ignition switch off

Below 1 V

  • *1: w/o Parking Support Brake System
  • *2: w/ Parking Support Brake System
NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

OK
  1. CHECK REAR TELEVISION CAMERA ASSEMBLY

(a) Replace the rear television camera assembly with a new or known good one.

Click here

(b) Check if the same malfunction reoccurs when the rear view monitor screen is displayed.

OK:

Malfunction does not reoccur (returns to normal).

OK

END (REAR TELEVISION CAMERA ASSEMBLY WAS DEFECTIVE)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY