Cylinder Block

In this manual: Cylinder Block
How To Troubleshoot Ecu Controlled Systems — 1How To Use This Manual — 1Identification Information — 1Repair Instruction — 1Terms — 12zr-fxe Air Cleaner Filter Element — 12zr-fxe Auxiliary Battery — 12zr-fxe Coolant (for Engine Coolant) — 12zr-fxe Oil And Oil Filter — 12zr-fxe Spark Plug — 1Air Conditioning Filter — 1Battery Cooling Filter — 1Brake Fluid — 1Coolant (for Inverter) — 1Front Brake Flexible Hose — 1Front Disc Brake Pad — 1Front Lower Ball Joint — 1Front Wheel Alignment — 1Front Wiper Rubber — 1General Maintenance — 1M20a-fxs Air Cleaner Filter Element — 1M20a-fxs Auxiliary Battery — 1M20a-fxs Coolant (for Engine Coolant) — 1M20a-fxs Oil And Oil Filter — 1M20a-fxs Spark Plug — 1Pa10/pb10/pb12 Hybrid Transaxle Fluid — 1Q810 Hybrid Transaxle Fluid — 1Rear Brake Flexible Hose — 1Rear Disc Brake Pad — 1Rear Wheel Alignment — 1Steering Column — 1Tire And Wheel — 1Transmitter Battery — 1When Disconnecting Or Reconnecting Battery Terminal — 1When Replacing Or Removing/installing Parts — 1Automatic High Beam Main Switch — 1Automatic High Beam System — 1Driver Monitor Camera — 1Driver Monitor Camera System — 1Driver Monitor Ecu — 1Front Camera — 1Front Camera System — 1Front Radar Sensor System — 1Front Side Radar Sensor — 1Front Side Radar Sensor System — 1Millimeter Wave Radar Sensor — 1Utility — 1Advanced Park — 1Advanced Park Main Switch — 1Amplifier Antenna — 1Audio And Visual System — 1Front Door Speaker — 1Instrument Panel Speaker — 1Microphone — 1Noise Filter — 1Pillar Speaker — 1Radio Antenna Cord (for Back Door) — 1Radio Antenna Cord (for Instrument Panel) — 1Radio Antenna Cord (for Roof) — 1Radio Receiver — 1Rear Door Speaker — 1Roof Antenna — 1Stereo Component Amplifier — 1Stereo Jack Adapter Assembly — 1Window Glass Antenna Wire — 1Back-up Battery — 1Dcm(telematics Transceiver) — 1Manual(sos)switch — 1Safety Connect System — 1Telephone And Gps Antenna (for Front Side) — 1Telephone And Gps Antenna (for Roof Side) — 1Telephone And Gps Antenna Cords — 1Garage Door Opener System (for Digital Inner Mirror) — 1Garage Door Opener System (for Ec Inner Mirror) — 1Blind Spot Monitor Sensor — 1Blind Spot Monitor System — 1Clearance Warning Ecu — 1Intuitive Parking Assist System — 1Panoramic View Monitor Switch — 1Panoramic View Monitor System — 1Parking Assist Ecu — 1Parking Assist Light — 1Parking Assist Monitor System — 1Parking Support Brake System — 1Rear View Monitor System — 1Television Camera (for Front) — 1Television Camera (for Rear) — 1Television Camera (for Side) — 1Ultrasonic Sensor (for Front) — 1Ultrasonic Sensor (for Rear) — 1Brake Actuator — 1Brake Pedal Stroke Sensor — 1Electronically Controlled Brake System — 1Front Speed Sensor — 1Rear Speed Sensor (for Awd) — 1Steering Angle Sensor — 1Brake Booster — 1Brake Fluid — 1Brake Line — 1Brake Pedal — 1Brake System — 1Electric Parking Brake Actuator — 1Electric Parking Brake Switch — 1Electric Parking Brake System — 1Forced Release — 1Front Axle Hub — 1Front Axle Hub Bolt — 1Rear Axle Carrier (for 2wd) — 1Rear Axle Carrier (for Awd) — 1Rear Axle Hub (for 2wd) — 1Rear Axle Hub (for Awd) — 1Rear Axle Hub Bolt — 1Steering Knuckle — 1Drive Shaft System — 1Front Drive Shaft Assembly — 1Rear Drive Shaft Assembly — 1Combination Switch — 1Electronic Shift Lever System — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Oil Seal — 1Hybrid Transaxle System — 1Input Shaft Oil Seal — 1Motor Cable — 1Pa10 Hybrid Vehicle Transaxle — 1Pa10 Manual Parking Lock Release — 1Pa10 Oil Cooler — 1Pb10/pb12 Hybrid Vehicle Transaxle — 1Pb10/pb12 Manual Parking Lock Release — 1Pb10/pb12 Oil Cooler — 1Shift Control Actuator — 1Shift Lever — 1Shift Lever Knob — 1Differential Side Gear Shaft — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Side Gear Oil Seal — 1Motor Cable — 1Rear Traction Motor — 1Coolant (for Engine) — 1Cooling Fan Motor — 1Cooling Fan System — 1Radiator — 1Relay — 1Thermostat — 1Water Pump — 1Canister — 1Egr Cooler — 1Egr Valve — 1Emission Control System — 1Fuel Tank Cap — 1Pcv Valve — 1Purge Valve — 1Vacuum Sensor — 1Air Fuel Ratio Sensor — 1Camshaft Oil Control Valve — 1Camshaft Position Sensor — 1Crankshaft Position Sensor — 1Ecm — 1Engine Coolant Temperature Sensor — 1Heated Oxygen Sensor — 1Ignition Coil And Spark Plug — 1Ignition System — 1Knock Sensor — 1Mass Air Flow Meter — 1Relay — 1Sfi System — 1Throttle Body — 1Camshaft — 1Cylinder Block — 1Cylinder Head — 1Cylinder Head Gasket — 1Engine — 1Engine Assembly — 1Engine Unit — 1Front Crankshaft Oil Seal — 1Rear Crankshaft Oil Seal — 1Fuel Filter — 1Fuel Injector — 1Fuel Pressure Regulator — 1Fuel Pump — 1Fuel Sender Gauge Assembly — 1Fuel System — 1Fuel Tank — 1Air Cleaner Filter Element — 1Exhaust Manifold — 1Exhaust Pipe — 1Intake Manifold — 1Intake System — 1Lubrication System — 1Oil And Oil Filter — 1Oil Pan And Oil Level Sensor — 1Oil Pressure Switch — 1Oil Pump — 1Accelerator Pedal Sensor — 1Battery Blower (for Hev Model) — 1Battery Ecu (for Hev Model) — 1Battery Ecu (for Phev Model) — 1Battery Voltage Sensor (for Phev Model) — 1Charge Cable (for Phev Model) — 1Charge Indicator (for Phev Model) — 1Charge Inlet (for Phev Model) — 1Combination Switch — 1Coolant (for Inverter) — 1Cooler (for Phev Model) — 1Electric Vehicle Charger Assembly (for Phev Model) — 1Frame Wire (for Hev Model) — 1Frame Wire (for Phev Model) — 1Heater Relay (for Phev Model) — 1Hv Battery (for Hev Model) — 1Hv Battery (for Phev Model) — 1Hv Battery Heater (for Phev Model) — 1Hv Battery Stack (for Phev Model) — 1Hv Relay Assembly (for Hev Model) — 1Hv Relay Assembly (for Phev Model) — 1Hybrid Battery System (for 2zr-fxe) — 1Hybrid Battery System (for M20a-fxs) — 1Hybrid Battery System (for Phev Model) — 1Hybrid Vehicle Control Ecu — 1Inverter With Converter (for Hev Model) — 1Motor Generator Control System (for 2zr-fxe) — 1Plug-in Charge Control System (for Phev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Service Plug Grip (for Hev Model) — 1Sub Radiator — 1Water Pump With Motor — 1Auxiliary Battery — 1Battery Current Sensor — 1Charging System — 1Solar Charging System — 1Solar Control Unit — 1Solar Roof — 1Can Communication System (for Hev Model) — 1Lin Communication System — 1Network Gateway Ecu — 1Integration Control Supply — 1Main Body Ecu — 1Power Integration System — 1Sub Battery System — 1Power Steering Ecu — 1Power Steering System — 1Heated Steering Wheel Controller — 1Heated Steering Wheel System — 1Steering Column Assembly — 1Steering Heater Switch — 1Steering Pad Switch — 1Steering System — 1Steering Wheel — 1Front Lower Ball Joint — 1Front Lower Suspension Arm (for 2zr-fxe Lh Side) — 1Front Lower Suspension Arm (for 2zr-fxe Rh Side) — 1Front Lower Suspension Arm (for M20a-fxs) — 1Front Shock Absorber — 1Front Stabilizer Bar — 1Front Suspension Member — 1Rear Coil Spring — 1Rear Lower Arm (for Awd Lh Side) — 1Rear Lower Arm (for Awd Rh Side) — 1Rear Lower Arm (for Hev Model 2wd) — 1Rear Lower Arm (for Phev Model) — 1Rear Shock Absorber — 1Rear Stabilizer Bar — 1Rear Suspension Member (for 2wd) — 1Rear Suspension Member (for Awd) — 1Rear Trailing Arm — 1Rear Upper Arm — 1Tire And Wheel System — 1Tire Repair Seal — 1Tire Pressure Warning Receiver — 1Tire Pressure Warning System — 1Tire Pressure Warning Valve — 1Acoustic Vehicle Alerting System — 1Vehicle Approaching Speaker — 1Vehicle Approaching Speaker Ecu — 1Back Door — 1Back Door Closer Ecu — 1Back Door Opener Switch — 1Back Door Support — 1Back Door Weatherstrip — 1Charge Lid Courtesy Switch — 1Charge Lid Opener Motor Assembly — 1Charge Lid Opener System — 1Charge Lid Opener Unit — 1Front Door — 1Front Door Opening Trim Weatherstrip — 1Fuel Lid Opener Motor Assembly — 1Fuel Lid Opener Switch — 1Fuel Lid Opener System — 1Hood — 1Hood Lock Control Cable Assembly — 1Power Back Door Closer Switch — 1Power Back Door Control Switch — 1Power Back Door Drive Unit — 1Power Back Door System — 1Power Back Door Touch Sensor — 1Power Back Door Warning Buzzer — 1Rear Door — 1Rear Door Opening Trim Weatherstrip — 1Reserve Lock Switch — 1Front Bumper — 1Front Door Belt Moulding — 1Front Door Window Frame Moulding — 1Front Fender — 1Front Pillar Upper Cover — 1Grille Shutter — 1Grille Shutter System — 1Name Plate — 1Quarter Garnish — 1Rear Bumper — 1Rear Door Belt Moulding — 1Rear Door Window Frame Moulding — 1Rear Wheel House Plate — 1Rocker Panel Moulding — 1Roof Drip Side Finish Moulding — 1Roof Garnish — 1Wheel Opening Moulding (for Front Side) — 1Wheel Opening Moulding (for Rear Side) — 1Windshield Outside Moulding — 1Horn — 1Horn System — 1Relay — 1Automatic Light Control Sensor — 1Back-up Light Assembly — 1Charge Lid Light — 1Front Marker Light — 1Hazard Warning Switch — 1Headlight Assembly — 1Headlight Dimmer Switch — 1Headlight Leveling Switch — 1High Mounted Stop Light Assembly — 1Illumination Light Assembly — 1License Plate Light Assembly — 1Lighting System — 1Rear Combination Light Assembly — 1Rear Light Assembly — 1Rear Side Marker Light Assembly — 1Relay — 1Side Turn Signal Light Assembly — 1Stop Light Switch — 1Switch Housing — 1Outer Mirror Switch — 1Outer Rear View Mirror — 1Outer Rear View Mirror Cover — 1Outer Rear View Mirror Glass — 1Power Mirror Control System — 1Back Door Glass — 1Front Passenger Side Power Window Switch — 1Power Window Control System — 1Power Window Master Switch — 1Power Window Regulator Motor (for Front Door) — 1Power Window Regulator Motor (for Rear Door) — 1Rear Power Window Switch — 1Relay — 1Roof Window Fix Glass — 1Window Defogger System — 1Windshield Deicer Switch — 1Windshield Deicer System — 1Windshield Glass — 1Front Wiper Motor — 1Rain Sensor — 1Relay — 1Washer Motor — 1Washer Nozzle (for Front Side) — 1Washer Nozzle (for Rear Television Camera) — 1Wiper And Washer System — 1Wiper Ecu — 1Wiper Switch — 1Back Door Lock — 1Door Control Receiver — 1Door Control Switch — 1Door Control Transmitter — 1Door Lock Release Motor (for Rear Side) — 1Door Outside Handle (for Rear Side) — 1Front Door Lock — 1Power Door Lock Control System — 1Rear Door Lock — 1Transmitter Battery — 1Wireless Door Lock Control System — 1Accumulator — 1Air Conditioning Amplifier — 1Air Conditioning Panel — 1Air Conditioning Pressure Sensor — 1Air Conditioning Unit — 1Ambient Temperature Sensor — 1Blower Unit — 1Condenser (for Hev Model) — 1Condenser (for Phev Model) — 1Discharge Temperature Sensor — 1Electric Expansion Valve (cooling) — 1Electric Expansion Valve (heating) — 1Evaporator Pipe Temperature Sensor — 1Evaporator Pressure Regulator — 1Front Blower Motor — 1Front Evaporator Front Solenoid Valve — 1Air Conditioning System (for Hev Model) — 1Front Evaporator Temperature Sensor — 1Heat Exchanger Temperature Sensor — 1Heat Pump Ecu — 1High Pressure Magnetic Valve — 1Humidity Sensor — 1Internal Condenser Temperature Sensor — 1Low Pressure Magnetic Valve — 1Refrigerant (for Hfc-134a(r134a)) — 1Refrigerant Line (for Hev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Room Temperature Sensor — 1Solar Sensor — 1Floor Carpet — 1Front Console Box — 1Instrument Panel Safety Pad — 1Roof Headlining — 1Roof Sunshade — 1Ambient Light (for Driver Side) — 1Ambient Light (for Front Passenger Side) — 1Back Door Courtesy Switch — 1Footwell Light — 1Glove Box Light — 1Lighting System — 1Luggage Compartment Room Light — 1Personal Light — 1Room Light — 1Vanity Light — 1Vanity Light Switch — 1Combination Meter — 1Meter / Gauge System — 1Trip Switch — 1Digital Inner Mirror — 1Digital Rear-view Mirror System — 1Inner Mirror Monitor Camera — 1Inner Rear View Mirror (w/o Ec Mirror) — 1Accessory Power Outlet System — 1Power Outlet Socket (for Console Box Front Side) — 1Power Outlet Socket (for Console Box Rear Side) — 1Power Outlet Socket (for Console Box) — 1Power Outlet Socket (for Luggage Compartment) — 1Power Outlet Switch — 1Wireless Charger Assembly — 1Wireless Charging System — 1Climate Control Seat System — 1Front Power Seat Control System (w/ Memory) — 1Front Power Seat Motor Assembly — 1Front Seat Assembly (for Power Seat) — 1Front Seat Cushion Heater (for Power Seat) — 1Front Seatback Heater (for Power Seat) — 1Lumbar Support Adjuster Assembly — 1Power Seat Control Ecu — 1Power Seat Switch — 1Power Seat Track Rail Assembly — 1Rear Seat Assembly — 1Rear Seat Cushion Heater — 1Rear Seat Reminder System — 1Rear Seatback Heater — 1Seat Heater Control — 1Seat Heater Switch (for Front Seat) — 1Seat Heater Switch (for Rear Side) — 1Seat Heater System — 1Seat Memory Switch — 1Child Restraint Seat Anchor Bracket — 1Front Seat Inner Belt Assembly — 1Front Seat Outer Belt Assembly — 1Occupant Detection Sensor (for Front Passenger Side) — 1Rear Center Seat Outer Belt Assembly — 1Rear Seat Inner Belt Assembly (for Rh Side) — 1Rear Seat Outer Belt Assembly — 1Seat Belt Warning System (w/ Occupant Classification System) — 1Tongue Plate Stopper — 1Airbag System — 1Center Airbag Sensor Assembly — 1Curtain Shield Airbag Assembly — 1Front Airbag Sensor — 1Front Passenger Airbag Assembly — 1Front Seat Side Airbag Assembly — 1Inspection After Collision — 1Knee Airbag Assembly — 1Occupant Classification System — 1Rear Seat Side Airbag Assembly — 1Side Airbag Sensor (for Center Pillar) — 1Side Airbag Sensor (for Front Door) — 1Spiral Cable — 1Steering Pad — 1Certification Ecu — 1Digital Key Ecu — 1Digital Key Receiver (for Front Floor) — 1Digital Key Receiver (for Outside Luggage Compartment) — 1Digital Key Receiver (for Rear Door) — 1Digital Key System — 1Electrical Key Oscillator (for Front Floor) — 1Electrical Key Oscillator (for Outside Luggage Compartment) — 1Electrical Key Oscillator (for Rear Floor) — 1Engine Hood Courtesy Switch — 1Id Code Box — 1Smart Key System (for Start Function) — 1
~37min read
2special tools
010203040502015N·mlb·ft
Tightening torque found on this page
  • Precaution
  • Disassembly
  • Inspection
  • Reassembly

Precaution

PRECAUTION

HINT:

  • Any digits beyond the 0.01 mm (1/1000 in.) place for standard, minimum and maximum values should be used as a reference only.
  • When both standard and maximum or minimum values are listed for an inspection, use the standard value as a reference only and base any judgments on the maximum and minimum values.

Disassembly

DISASSEMBLY

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during engine unit removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

*1: Also necessary after performing a tire rotation.

*2: It is not necessary to perform this procedure if the tire pressure warning valve and transmitters are installed to the same location.

Replacement of ECM

Update ECU security key

Toyota Prius Vehicle Control History (RoB) are stored

ECU configuration

-

Perform Toyota Prius Vehicle Identification Number (VIN) registration

DTC is output

  • Replacement of throttle body assembly
  • Replacement of cylinder head sub-assembly
  • Replacement of camshaft (for intake or exhaust camshaft)
  • Replacement of camshaft timing gear assembly
  • Replacement of piston or piston ring
  • Replacement of fuel injector assembly
  • Replacement of spark plug
  • Replacement of ignition coil assembly
  • Replacement of EGR valve assembly
  • Gas leak from exhaust system is repaired
  • Replacement of knock control sensor

Inspection after repair

  • Poor idle, etc.
  • Engine start function, etc.

Replacement of inverter with converter assembly

ECU configuration

-

Resolver learning

  • DTCs are stored
  • Slight vibration at a Toyota Prius vehicle speed of 5 km/h or less
  • Shock or vibration during acceleration

Replacement of hybrid vehicle transaxle assembly

  • Resolver learning
  • Initialize resolver
  • DTCs are stored
  • Slight vibration at a Toyota Prius vehicle speed of 5 km/h or less
  • Shock or vibration during acceleration

Suspension parts

Rear television camera assembly optical axis (Back camera position setting)

Parking Assist Monitor System

Parking assist ECU initialization

Panoramic View Monitor System

Advanced Park

Tires

  • Initialization*1*2
  • Tire Position Identification*1*2

Tire Pressure Warning System

Refer to Procedures Necessary When Replacing Parts (for Tire Pressure Warning System) table below

Rear television camera assembly optical axis (Back camera position setting)

Parking Assist Monitor System

Parking assist ECU initialization

Panoramic View Monitor System

Advanced Park

Replacement of front bumper assembly*

Front television camera view adjustment

Panoramic View Monitor System

Advanced Park

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

  • Learning completes when Toyota Prius vehicle is driven

    Effect/Inoperative Function When Necessary Procedures are not Performed

    Necessary Procedures

    Link

    Front Camera System

    Drive the Toyota Prius vehicle straight ahead at 35 km/h or more for 5 seconds or more.

  • Learning completes when vehicle is operated normally

    Effect/Inoperative Function When Necessary Procedures are not Performed

    Necessary Procedures

    Link

    *1: w/o Power Back Door System

    *2: w/ Power Back Door System

    Power Door Lock Control System*1

    • Back door opener

    Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.

    Power Back Door System*2

    Reset back door close position

    Air Conditioning System

    After the ignition switch is turned to ON, the servo motor standard position is recognized.

    -

COMPONENTS (DESASSEMBLY)

Procedure

Part Name Code

1

NO. 1 VENTILATION CASE

12211

-

-

2

CONNECTING ROD CAP

-

-

-

3

PISTON SUB-ASSEMBLY WITH CONNECTING ROD

-

-

-

4

CONNECTING ROD BEARING

13041

-

-

-

5

PISTON RING SET

13011

-

-

6

PISTON PIN

-

-

-

7

CRANKSHAFT BEARING CAP

-

-

-

8

CRANKSHAFT

13411

-

-

-

9

UPPER CRANKSHAFT THRUST WASHER

11791

-

-

-

10

CRANKSHAFT BEARING

11711

-

-

-

11

CONNECTING ROD SMALL END BUSH

13201A

-

-

*A

Type A

*B

Type B

●

Non-reusable part

-

-

Procedure

Part Name Code

12

NO. 1 OIL NOZZLE SUB-ASSEMBLY

15708

-

-

13

RING PIN

-

-

-

14

STRAIGHT PIN

-

-

-

15

STUD BOLT

-

-

-

16

CLEAN CYLINDER BLOCK

-

-

-

●

Non-reusable part

-

-

PROCEDURE

1. REMOVE NO. 1 VENTILATION CASE

*A

Type A

*B

Type B

(1) Type A:

Remove the 6 bolts and 2 nuts.

(2) Type B:

Remove the 8 bolts.

(3) Remove the No. 1 ventilation case by prying between the No. 1 ventilation case and cylinder block sub-assembly with a screwdriver with its tip wrapped with protective tape.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder block sub-assembly and No. 1 ventilation case.

2. REMOVE CONNECTING ROD CAP

*a

Paint Mark

-

-

(1) Place a paint mark across each corresponding connecting rod and connecting rod cap.

HINT:

The paint marks are used to ensure that the same parts are installed in the same combination to their original locations.

(2) Using SST, remove the 8 connecting rod bolts from the connecting rod caps.

SST: 09205-16011

(3) Using the 2 removed connecting rod bolts, remove the 4 connecting rod caps with connecting rod bearings by wiggling each connecting rod cap left and right.

HINT:

Keep the connecting rod bearing installed to the connecting rod cap.

3. REMOVE PISTON SUB-ASSEMBLY WITH CONNECTING ROD

(1) Using a ridge reamer, scrape off any carbon on the top of the cylinder.

(2) Push out the 4 pistons with 4 connecting rods and 4 connecting rod bearings through the top of the cylinder block sub-assembly.

HINT:

  • Keep the connecting rod bearings, connecting rods and connecting rod caps together.
  • Arrange the removed parts in such a way that they can be reinstalled to their original locations.

4. REMOVE CONNECTING ROD BEARING

5. REMOVE PISTON RING SET

(1) Using a piston ring expander, remove the No. 1 compression ring and No. 2 compression ring from the piston.

(2) Remove the oil ring expander, upper side rail and lower side rail from the piston by hand.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.

6. REMOVE PISTON PIN

(1) Using a screwdriver, pry out the piston pin hole snap ring from the piston.

NOTICE:

  • Do not remove the piston pin hole snap ring (rear side) unless it is being replaced.
  • Be careful not to damage the piston when removing the piston pin hole snap ring (rear side).

(2) Gradually heat each piston to approximately 80 to 90 °C.

CAUTION:

Be sure to wear protective gloves.

(3) Using a plastic hammer and brass bar, lightly tap out the piston pin and remove the connecting rod.

HINT:

  • The piston and piston pin are a matched set.
  • Arrange the pistons, piston pins, piston rings, connecting rods and connecting rod bearings in the correct order.

7. REMOVE CRANKSHAFT BEARING CAP

(1) Uniformly loosen and remove the 10 crankshaft bearing cap set bolts in several steps in the order shown in the illustration.

(2) Using the 2 removed crankshaft bearing cap set bolts, remove the 5 crankshaft bearing caps from the cylinder block sub-assembly by wiggling each crankshaft bearing cap back and forth.

8. REMOVE CRANKSHAFT

9. REMOVE UPPER CRANKSHAFT THRUST WASHER

10. REMOVE CRANKSHAFT BEARING

11. REMOVE CONNECTING ROD SMALL END BUSH

(1) Using SST and a press, press out the connecting rod small end bush.

SST: 09222-30010

12. REMOVE NO. 1 OIL NOZZLE SUB-ASSEMBLY

(1) Using a 5 mm hexagon socket wrench, remove the 4 bolts and 4 No. 1 oil nozzle sub-assemblies from the cylinder block sub-assembly.

13. REMOVE RING PIN

NOTICE:

It is not necessary to remove the ring pins unless they are being replaced.

14. REMOVE STRAIGHT PIN

NOTICE:

It is not necessary to remove the straight pins unless they are being replaced.

15. REMOVE STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.

(1) Using an E6 "TORX" socket wrench, remove the 2 stud bolts from the cylinder block sub-assembly.

16. CLEAN CYLINDER BLOCK

NOTICE:

If the cylinder is washed at high temperature, the cylinder liner will stick out beyond the cylinder block. Always wash the cylinder block at a temperature of 45 °C or less.

Inspection

INSPECTION

PROCEDURE

1. INSPECT CONNECTING ROD THRUST CLEARANCE

(a) Using a dial indicator, measure the thrust clearance while moving the connecting rod back and forth.

Standard Thrust Clearance:

Maximum Thrust Clearance

Specified Condition

Result

0.342 mm

0.0135 in.

0.160 to 0.342 mm

0.00630 to 0.0135 in.

mm

in.

(b) If the thrust clearance is more than the maximum, replace the connecting rod. If necessary, replace the crankshaft.

2. INSPECT CONNECTING ROD OIL CLEARANCE

HINT:

Using SST, install and alternately tighten the 2 connecting rod bolts in several steps.

Pre-procedure1

(a) Remove the connecting rod cap.

HINT:

Click here

(b) Remove the connecting rod bearing.

HINT:

Click here

(c) Clean the crankshaft crank pin and connecting rod bearing.

(d) Check the crankshaft crank pin and connecting rod bearing for pitting and scratches.

(e) If the crank pin or upper connecting rod bearing is damaged, replace the connecting rod bearings. If necessary, replace the crankshaft.

(f) Lay a strip of Plastigage on the crank pin.

*a

Plastigage

(g) Check that the front mark of the connecting rod cap is facing the correct direction, and install the connecting rod bearing cap to the connecting rod.

*a

Front Mark

(h) Apply a light coat of engine oil to the threads and under the heads of the 2 connecting rod bolts.

(i) Using SST, install and alternately tighten the 2 connecting rod bolts in several steps.

SST: 09205-16011

Torque:

20 N·m {204 kgf·cm, 15 ft·lbf}

(j) Mark the front of each connecting rod bolt with paint.

*a

Paint Mark

*b

90°

Front of Engine

(k) Tighten the connecting rod bolts 90° as shown in the illustration.

NOTICE:

Do not turn the crankshaft during the measurement.

(l) Remove the 2 connecting rod bolts and connecting rod bearing cap.

Procedure1

(m) Measure the Plastigage at its widest point.

Standard Oil Clearance:

Maximum Oil Clearance

Specified Condition

Result

0.070 mm

0.00276 in.

0.014 to 0.038 mm

0.000551 to 0.00150 in.

mm

in.

HINT:

If replacing a connecting rod bearing, select a new one with the same number as marked on the connecting rod cap. There are 3 sizes of standard connecting rod bearings, marked "1", "2", or "3" accordingly.

Standard Connecting Rod Large End Bore Diameter:

Mark

Specified Condition

1

47.000 to 47.008 mm (1.85039 to 1.85070 in.)

2

47.009 to 47.016 mm (1.85074 to 1.85102 in.)

3

47.017 to 47.024 mm (1.85106 to 1.85133 in.)

Standard Connecting Rod Bearing Thickness:

Mark

Specified Condition

1

1.489 to 1.493 mm (0.05862 to 0.05878 in.)

2

1.494 to 1.497 mm (0.05882 to 0.05894 in.)

3

1.498 to 1.501 mm (0.05898 to 0.05909 in.)

Standard Crankshaft Pin Diameter:

Specified Condition

Result

43.992 to 44.000 mm

1.73197 to 1.73228 in.

mm

in.

NOTICE:

Completely remove the Plastigage after the measurement.

*a

Plastigage

*b

1, 2 or 3 Mark

(n) If the oil clearance is more than the maximum, replace the connecting rod bearings. If necessary, replace the crankshaft.

Post-procedure1

(o) None

3. INSPECT CRANKSHAFT THRUST CLEARANCE

(a) Using a dial indicator, measure the crankshaft thrust clearance while prying the crankshaft back and forth with a screwdriver.

Standard Thrust Clearance:

Maximum Thrust Clearance

Specified Condition

Result

0.18 mm

0.00709 in.

0.04 to 0.14 mm

0.00157 to 0.00551 in.

mm

in.

Standard Thrust Washer Thickness:

Specified Condition

Result

2.43 to 2.48 mm

0.0957 to 0.0976 in.

mm

in.

(b) If the thrust clearance is more than the maximum, replace the crankshaft thrust washer set. If necessary, replace the crankshaft.

4. INSPECT CRANKSHAFT OIL CLEARANCE

Pre-procedure1

(a) Check the crankshaft journals and crankshaft bearings for pitting and scratches.

(b) Install the crankshaft bearings.

HINT:

Click here

(c) Install the upper crankshaft thrust washers.

HINT:

Click here

(d) Clean each main journal and crankshaft bearing.

(e) Place the crankshaft on the cylinder block sub-assembly.

(f) Lay a strip of Plastigage across each journal.

*a

Plastigage

(g) Confirm the front marks and numbers, and place the 5 crankshaft bearing caps on the cylinder block sub-assembly.

HINT:

A number is marked on each crankshaft bearing cap to indicate the installation position.

*a

Front Mark and Number

(h) Install the crankshaft bearing caps.

NOTICE:

Do not turn the crankshaft.

HINT:

Click here

(i) Remove the crankshaft bearing caps.

HINT:

Click here

Procedure1

(j) Measure the Plastigage at its widest point.

*a

No. 1

*b

No. 2

*c

No. 3

*d

No. 4

*e

No. 5

*f

Plastigage

*g

Cylinder Block Number Mark

*h

Crankshaft Number Mark

*i

Diameter Mark

-

-

Standard Oil Clearance:

Maximum Warpage

Specified Condition

Result

0.05 mm

0.00197 in.

0.014 to 0.038 mm

0.00055 to 0.00150 in.

mm

in.

NOTICE:

Completely remove the Plastigage after the measurement.

(k) If replacing a crankshaft bearing, select a new one with the same number.

HINT:

  • If the number of the crankshaft bearing cannot be determined, select the correct crankshaft bearing number by adding together the numbers imprinted on the cylinder block sub-assembly and crankshaft. Then refer to the following table for the appropriate crankshaft bearing number. There are 4 sizes of standard crankshaft bearings, marked "1", "2", "3" or "4" accordingly.
  • Example: Cylinder block "4" Crankshaft "3" = Total number 7 (Use crankshaft bearing "3")

Crankshaft Bearing:

Cylinder block sub-assembly Crankshaft

Crankshaft bearing to be used

0 to 2

"1"

3 to 5

"2"

6 to 8

"3"

9 to 11

"4"

Standard Cylinder Block Journal Bore Diameter:

Mark

Specified Condition

0

52.000 to 52.002 mm (2.04724 to 2.04732 in.)

1

52.003 to 52.004 mm (2.04736 to 2.04740 in.)

2

52.005 to 52.006 mm (2.04744 to 2.04748 in.)

3

52.007 to 52.009 mm (2.04752 to 2.04759 in.)

4

52.010 to 52.011 mm (2.04763 to 2.04767 in.)

5

52.012 to 52.013 mm (2.04771 to 2.04775 in.)

6

52.014 to 52.016 mm (2.04779 to 2.04787 in.)

Standard Crankshaft Journal Diameter:

Mark

Specified Condition

0

47.999 to 48.000 mm (1.88972 to 1.88976 in.)

1

47.997 to 47.998 mm (1.88964 to 1.88968 in.)

2

47.995 to 47.996 mm (1.88956 to 1.88960 in.)

3

47.993 to 47.994 mm (1.88948 to 1.88952 in.)

4

47.991 to 47.992 mm (1.88941 to 1.88945 in.)

5

47.988 to 47.990 mm (1.88929 to 1.88937 in.)

Standard Bearing Center Wall Thickness:

Mark

Specified Condition

1

1.991 to 1.994 mm (0.07839 to 0.07850 in.)

2

1.995 to 1.997 mm (0.07854 to 0.07862 in.)

3

1.998 to 2.000 mm (0.07866 to 0.07874 in.)

4

2.001 to 2.003 mm (0.07878 to 0.07886 in.)

Post-procedure1

(l) None

5. INSPECT CYLINDER BLOCK FOR WARPAGE

(a) Using a precision straightedge and feeler gauge, check the surfaces which contact the cylinder head gasket for warpage.

Maximum Warpage:

Specified Condition

Result

0.05 mm

0.00197 in.

mm

in.

(b) If the warpage is more than the maximum, replace the cylinder block sub-assembly.

6. INSPECT CYLINDER BORE

(a) Using a cylinder gauge, measure the cylinder bore diameter at the positions (A) and (B) in the thrust and axial directions.

*a

Thrust Direction

*b

Axial Direction

Front of Engine

Reference Diameter (New Parts):

Maximum Diameter

Specified Condition

Result

80.63 mm

3.17 in.

80.500 to 80.513 mm

3.16929 to 3.16980 in.

mm

in.

Measurement Position:

Measurement Position

Cylinder Bore Position

(A)

10 mm (0.394 in.) from top edge

(B)

50 mm (1.97 in.) from top edge

(b) If the average diameter of 4 positions is more than the maximum, replace the cylinder block sub-assembly.

7. INSPECT NO. 1 OIL NOZZLE SUB-ASSEMBLY

(a) Push the check valve with a pin to check that it is not stuck.

*a

Pin

(b) If the check valve is stuck, replace the No. 1 oil nozzle sub-assembly.

(c) Apply air into (A). Check that air does not leak through (B).

(d) If air leaks, clean or replace the No. 1 oil nozzle sub-assembly.

(e) Push the check valve with a pin while applying air into (A). Check that air passes through (B).

*a

Pin

(f) If air does not pass through (B), clean or replace the No. 1 oil nozzle sub-assembly.

8. INSPECT PISTON SUB-ASSEMBLY WITH CONNECTING ROD

(a) Check the fitting condition between the piston and piston pin by trying to move the piston back and forth on the piston pin.

(b) If abnormal movement is felt, replace the piston and piston pin as a set.

9. INSPECT PISTON

(a) Using a micrometer, measure the piston diameter at a position 9.0 mm (0.354 in.) from the bottom of the piston (refer to the illustration).

Reference Piston Diameter (New Parts):

Distance

Specified Condition

Result

9.0 mm

0.354 in.

80.473 to 80.503 mm

3.16822 to 3.16940 in.

mm

in.

*a

9.0 mm

(b) If the piston diameter is less than the minimum, replace the piston and piston pin as a set.

10. INSPECT PISTON OIL CLEARANCE

(a) Subtract the piston diameter measurement from the cylinder bore diameter measurement.

Reference Oil Clearance (New Parts):

Maximum Oil Clearance

Specified Condition

Result

0.08 mm

0.00315 in.

-0.003 to 0.040 mm

-0.000118 to 0.00157 in.

mm

in.

(b) If the piston oil clearance is more than the maximum, replace all the pistons with piston pins. If necessary, replace the cylinder block sub-assembly.

11. INSPECT RING GROOVE CLEARANCE

(a) Using a feeler gauge, measure the clearance between a new piston ring set and the wall of the ring groove.

Standard Ring Groove Clearance:

Item

Specified Condition

Result

No. 1 Compression Ring

0.02 to 0.07 mm

0.000787 to 0.00276 in.

mm

in.

No. 2 Compression Ring

0.02 to 0.06 mm

0.000787 to 0.00236 in.

mm

in.

Oil Ring

0.07 to 0.13 mm

0.00276 to 0.00512 in.

mm

in.

(b) If the groove clearance is not as specified, replace the piston and piston pin as a set.

12. INSPECT PISTON RING END GAP

Pre-procedure1

(a) Using a piston, push the piston ring a little beyond the bottom of the ring travel, 50 mm (1.97 in.) from the top of the cylinder block sub-assembly.

*a

50 mm

Procedure1

(b) Using a feeler gauge, measure the end gap.

Standard End Gap:

Item

Maximum End Gap

Specified Condition

Result

No. 1 compression ring

0.5 mm

0.0197 in.

0.20 to 0.25 mm

0.00787 to 0.00984 in.

mm

in.

No. 2 compression ring

0.7 mm

0.0276 in.

0.30 to 0.50 mm

0.0118 to 0.0197 in.

mm

in.

Oil ring

0.7 mm

0.0276 in.

0.10 to 0.35 mm

0.00394 to 0.0138 in.

mm

in.

(c) If the end gap is more than the maximum, replace the piston ring. If the end gap is more than the maximum even with a new piston ring, replace the cylinder block sub-assembly.

Post-procedure1

(d) None

13. INSPECT PISTON PIN OIL CLEARANCE

HINT:

When replacing the piston and piston pin with supply parts, there are a number of piston diameter sizes to choose from, but there is only one size of piston pin diameter.

(a) Using a caliper gauge, measure the piston pin bore diameter.

Standard Piston Pin Bore Diameter:

20.006 to 20.015 mm (0.78764 to 0.78799 in.)

Item

Specified Condition

Result

Mark A

20.006 to 20.009 mm

0.78764 to 0.78775 in.

mm

in.

Mark B

20.010 to 20.012 mm

0.78779 to 0.78787 in.

mm

in.

Mark C

20.013 to 20.015 mm

0.78791 to 0.78799 in.

mm

in.

(b) If the diameter is not as specified, replace the piston and piston pin as a set.

(c) Using a micrometer, measure the piston pin diameter.

Standard Piston Pin Diameter:

20.004 to 20.013 mm (0.78756 to 0.78791 in.)

Item

Specified Condition

Result

Mark A

20.004 to 20.007 mm

0.78756 to 0.78768 in.

mm

in.

Mark B

20.008 to 20.010 mm

0.78772 to 0.78779 in.

mm

in.

Mark C

20.011 to 20.013 mm

0.78783 to 0.78791 in.

mm

in.

Measurement Position:

Measurement Position

Piston Pin Position

a

5 mm (0.197 in.) from side edge

b

25 mm (0.984 in.) from side edge

(d) If the diameter is not as specified, replace the piston and piston pin as a set.

(e) Using a caliper gauge, measure the connecting rod small end bush bore diameter.

Standard Connecting Rod Small End Bush Bore Diameter:

20.012 to 20.021 mm (0.78787 to 0.78823 in.)

Item

Specified Condition

Result

Mark A

20.012 to 20.015 mm

0.78787 to 0.78799 in.

mm

in.

Mark B

20.016 to 20.018 mm

0.78803 to 0.78811 in.

mm

in.

Mark C

20.019 to 20.021 mm

0.78815 to 0.78823 in.

mm

in.

(f) If the diameter is not as specified, replace the connecting rod small end bush.

(g) Subtract the piston pin diameter measurement from the piston pin bore diameter measurement.

Standard Oil Clearance:

Maximum Oil Clearance

Specified Condition

Result

0.010 mm

0.000394 in.

-0.001 to 0.005 mm

-0.0000394 to 0.000197 in.

mm

in.

*a

Upper Side

*b

Lower Side

*c

Front Mark

*d

Piston Pin Bore Diameter Mark

*e

Connecting Rod Small End Bush Bore Diameter Mark

(h) If the oil clearance is more than the maximum, replace the piston and piston pin as a set.

(i) Subtract the piston pin diameter measurement from the bushing inside diameter measurement.

Standard Oil Clearance:

Maximum Oil Clearance

Specified Condition

Result

0.014 mm

0.000551 in.

0.005 to 0.011 mm

0.000197 to 0.000433 in.

mm

in.

(j) If the oil clearance is more than the maximum, replace the connecting rod small end bush. If necessary, replace the piston and piston pin as a set.

14. INSPECT CONNECTING ROD BOLT

(a) Using a vernier caliper, measure the diameter of the connecting rod bolt at several points within the area shown in the illustration.

Standard Diameter:

Minimum Diameter

Specified Condition

Result

6.4 mm

0.252 in.

6.6 to 6.7 mm

0.260 to 0.264 in.

mm

in.

NOTICE:

  • Diameter measurements should be done at several points.
  • If the diameter is less than the minimum, replace the connecting rod bolt with a new one. Failure to do so may lead to engine damage.
  • If there is any thread deformation, replace the connecting rod bolt with a new one.

*a

Measurement Area

(b) If the diameter is less than the minimum, replace the connecting rod bolt.

15. INSPECT CRANKSHAFT

(a) Inspect the runout.

(1) Using a dial indicator and V-blocks, measure the runout as shown in the illustration.

Maximum Runout:

Specified Condition

Result

0.03 mm

0.00118 in.

mm

in.

(2) If the runout is more than the maximum, replace the crankshaft.

(b) Inspect the main journals.

(1) Using a micrometer, measure the diameter of each main journal.

Standard Diameter:

47.988 to 48.000 mm (1.88929 to 1.88976 in.)

Standard Diameter (Reference):

Mark

Specified Condition

0

47.999 to 48.000 mm (1.88972 to 1.88976 in.)

1

47.997 to 47.998 mm (1.88964 to 1.88968 in.)

2

47.995 to 47.996 mm (1.88956 to 1.88960 in.)

3

47.993 to 47.994 mm (1.88948 to 1.88952 in.)

4

47.991 to 47.992 mm (1.88941 to 1.88945 in.)

5

47.988 to 47.990 mm (1.88929 to 1.88937 in.)

(2) If the diameter is not as specified, check the crankshaft oil clearance.

(3) Check each main journal for taper and out-of-round as shown in the illustration.

Maximum Taper and Out-of-Round:

Specified Condition

Result

0.004 mm

0.000157 in.

mm

in.

(4) If the taper or out-of-round is more than the maximum, replace the crankshaft.

(c) Inspect the crank pins.

(1) Using a micrometer, measure the diameter of each crank pin.

Standard Diameter:

Specified Condition

Result

43.992 to 44.000 mm

1.73197 to 1.73228 in.

mm

in.

(2) If the diameter is not as specified, check the connecting rod oil clearance.

(3) Inspect each crank pin for taper and out-of-round.

Maximum Taper and Out-of-Round:

Specified Condition

Result

0.004 mm

0.000157 in.

mm

in.

(4) If the taper or out-of-round is more than the maximum, replace the crankshaft.

16. INSPECT CRANKSHAFT BEARING CAP SET BOLT

(a) Using a vernier caliper, measure the length of the crankshaft bearing cap set bolt from the seat to the end.

Standard Length:

Maximum Length

Specified Condition

Result

86.7 mm

3.41 in.

84.3 to 85.7 mm

3.32 to 3.37 in.

mm

in.

NOTICE:

  • If the length is greater than the maximum, replace the crankshaft bearing cap set bolt with a new one. Failure to do so may lead to engine damage.
  • If there is any thread deformation, replace the crankshaft bearing cap set bolt with a new one.

*a

Measurement Length

*b

Measurement Area

*c

55 mm (2.17 in.)

(b) Using a vernier caliper, measure the minimum diameter of the threads at several points within the area shown in the illustration.

Standard Diameter:

Measurement Point (Distance from the Seat)

Minimum Diameter

Specified Condition

Result

55 mm

2.17 in.

9.1 mm

0.358 in.

9.77 to 9.96 mm

0.385 to 0.392 in.

mm

in.

NOTICE:

  • Diameter measurements should be done at several points.
  • If the diameter is less than the minimum, replace the crankshaft bearing cap set bolt with a new one. Failure to do so may lead to engine damage.
  • If there is any thread deformation, replace the crankshaft bearing cap set bolt with a new one.

Reassembly

REASSEMBLY

HINT:

Perform "Inspection After Repair" after replacing the piston or piston ring.

Click here

COMPONENTS (REASSEMBLY)

Procedure

Part Name Code

1

STUD BOLT

-

-

-

2

STRAIGHT PIN

-

-

-

3

RING PIN

-

-

-

4

NO. 1 OIL NOZZLE SUB-ASSEMBLY

15708

-

-

N*m (kgf*cm, ft.*lbf): Specified torque

●

Non-reusable part

Procedure

Part Name Code

5

CONNECTING ROD SMALL END BUSH

13201A

-

-

6

PISTON PIN

-

-

-

7

PISTON RING SET

13011

-

-

8

CRANKSHAFT BEARING

11711

-

-

9

UPPER CRANKSHAFT THRUST WASHER

11791

-

-

10

CRANKSHAFT

13411

-

-

11

CRANKSHAFT BEARING CAP

-

-

-

12

CONNECTING ROD BEARING

13041

-

-

13

PISTON SUB-ASSEMBLY WITH CONNECTING ROD

-

-

-

14

CONNECTING ROD CAP

-

-

-

15

NO. 1 VENTILATION CASE

12211

-

-

*A

Type A

*B

Type B

Tightening torque for "Major areas involving basic Toyota Prius vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf)

N*m (kgf*cm, ft.*lbf): Specified torque

●

Non-reusable part

-

-

*T1

1st: 40 (408, 30)

2nd: Turn 90°

*T2

1st: 20 (204, 15)

2nd: Turn 90°

PROCEDURE

1. INSTALL STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.

*a

LH Side

*b

16 mm (0.630 in.)

*c

9 mm (0.354 in.)

*d

27 mm (1.06 in.)

(1) Using an E6 "TORX" socket wrench, install the 2 stud bolts to the cylinder block sub-assembly as shown in the illustration.

Torque:

5 N·m {51 kgf·cm, 44 in·lbf}

2. INSTALL STRAIGHT PIN

NOTICE:

It is not necessary to remove the straight pins unless they are being replaced.

*a

Front Side

*b

Bottom Side

*c

Rear Side

*d

Width

*e

Height

*f

Protrusion Height

(1) Using a plastic hammer, tap in new straight pins to the cylinder block sub-assembly.

Standard Straight Pin:

Item

Height

Width

Protrusion Height

Pin (A)

36 mm (1.42 in.)

10 mm (0.394 in.)

18.5 to 19.5 mm (0.728 to 0.768 in.)

Pin (B)

12 mm (0.472 in.)

4 mm (0.157 in.)

5.0 to 7.0 mm (0.197 to 0.276 in.)

Pin (C)

18 mm (0.709 in.)

8 mm (0.315 in.)

8.0 to 10.0 mm (0.315 to 0.394 in.)

Pin (D)

22 mm (0.866 in.)

10 mm (0.394 in.)

11.0 to 13.0 mm (0.433 to 0.512 in.)

3. INSTALL RING PIN

NOTICE:

It is not necessary to remove the ring pins unless they are being replaced.

*a

Upper Side

*b

Width

*c

Height

*d

Protrusion Height

(1) Using a plastic hammer, tap 2 new ring pins into the cylinder block sub-assembly.

Standard Ring Pin

Item

Height

Width

Protrusion Height

Ring Pin

14.3 to 14.7 mm (0.563 to 0.579 in.)

12.9 to 13.0 mm (0.508 to 0.512 in.)

7.5 to 8.5 mm (0.295 to 0.335 in.)

4. INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY

(1) Using a 5 mm socket hexagon wrench, install the 4 No. 1 oil nozzle sub-assemblies with the 4 bolts.

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

5. INSTALL CONNECTING ROD SMALL END BUSH

*a

Oil Hole

-

-

(1) Align the oil holes of a new connecting rod small end bush and the connecting rod.

(2) Using SST and a press, press in the connecting rod small end bush.

SST: 09222-30010

(3) Using a pin hole grinder, hone the connecting rod small end bush to obtain the standard oil clearance between the connecting rod small end bush and piston pin.

Standard Oil Clearance:

0.005 to 0.011 mm (0.000197 to 0.000433 in.)

(4) Coat the piston pin with engine oil. Push the piston pin into the connecting rod with your thumb to check that the piston pin fits at normal room temperature.

6. INSTALL PISTON PIN

HINT:

Perform this procedure only when replacement of the piston pin hole snap ring (rear side) is necessary.

*a

Front Mark

*b

Cutout

(1) Using a screwdriver, install a new piston pin hole snap ring (rear side) at one end of the piston pin hole.

(2) Gradually heat the piston to approximately 80 to 90 °C.

CAUTION:

Be sure to wear protective gloves.

(3) Align the front marks of the piston and connecting rod, insert the connecting rod into the piston, and then push in the piston pin with your thumb until the piston pin comes into contact with the snap ring.

HINT:

The piston and piston pin are a matched set.

(4) Using a screwdriver, install a new piston pin hole snap ring at the other end of the piston pin hole.

NOTICE:

Make sure that the end gap of the snap ring is not aligned with the cutout of the piston pin hole.

(5) Check the fitting condition between the piston and piston pin by trying to move the piston back and forth on the piston pin.

HINT:

Perform "Inspection After Repair" after replacing the piston.

Click here

7. INSTALL PISTON RING SET

*1

Upper Side Rail

*2

Oil Ring Expander

*3

Lower Side Rail

-

-

*a

Press around the circumference

*b

Ring End

*c

Correct

*d

Incorrect (Ends of the oil ring expander are overlapping)

(1) Install the oil ring expander, upper side rail and lower side rail to the piston by hand.

NOTICE:

When installing the upper side rail and lower side rail, the ends of the oil ring expander may overlap. If it occurs, the upper side rail or lower side rail may move out of its groove.

(2) Check that the ends of the oil ring expander are not overlapping and that the upper side rail and lower side rail are securely installed into the groove.

NOTICE:

  • After installing the oil ring expander, upper side rail and lower side rail, press around the circumference with a finger to check that they are securely installed into the groove.
  • If the oil ring expander is not securely installed into the groove, check that the ends of the oil ring expander are not overlapping.
  • If the ends of the oil ring expander are overlapping, remove the upper side rail and lower side rail and realign the oil ring expander using a screwdriver.

*1

No. 1 Compression Ring and Oil Ring Expander

*2

No. 2 Compression Ring

*3

Upper Side Rail

*4

Lower Side Rail

*a

No. 1 Compression Ring

*b

No. 2 Compression Ring

*c

Code Mark

*d

Paint Mark

*e

Code Mark (No mark)

*f

Code Mark (2T)

*g

Front of Engine

-

-

Upward

-

-

(1) Using a piston ring expander, install the No. 1 compression ring and No. 2 compression ring so that the paint marks are positioned as shown in the illustration.

NOTICE:

  • Install the No. 2 compression ring with the code mark (2T) facing upward.
  • Paint marks can only be checked on new compression rings. When reusing compression rings, check each compression ring profile in order to install them into the correct positions.

(2) Position the piston ring set so that the ring ends are as shown in the illustration.

HINT:

Perform "Inspection After Repair" after replacing the piston ring.

Click here

8. INSTALL CRANKSHAFT BEARING

*a

Scale

*b

Vernier Caliper

(1) Install the 4 upper crankshaft bearings (except the No. 3 journal).

1. Install the 4 upper crankshaft bearings to the cylinder block sub-assembly.

NOTICE:

Do not apply engine oil to the 4 upper crankshaft bearings or the contact surfaces.

HINT:

Both sides of the oil groove in the cylinder block sub-assembly should be visible through the oil feed holes in the crankshaft bearing. The amount visible on each side of the holes should be equal.

2. Using a scale, measure the distance between the cylinder block sub-assembly edge and the crankshaft bearing edge.

Dimension (A):

0.5 to 1.0 mm (0.0197 to 0.0394 in.)

(2) Install the crankshaft bearing (for No. 3 journal).

1. Install the crankshaft bearing to the cylinder block sub-assembly.

NOTICE:

Do not apply engine oil to the upper crankshaft bearing or the contact surface.

HINT:

Both sides of the oil groove in the cylinder block sub-assembly should be visible through the oil feed holes in the upper crankshaft bearing. The amount visible on each side of the holes should be equal.

2. Using a vernier caliper, measure the distance between the cylinder block sub-assembly edge and the crankshaft bearing edge.

Difference between (B) and (C):

0.5 mm (0.0197 in.) or less

(3) Install the crankshaft bearing.

1. Install the crankshaft bearing to the cylinder block sub-assembly.

HINT:

Both sides of the oil groove in the cylinder block sub-assembly should be visible through the oil feed holes in the crankshaft bearing. The amount visible on each side of the holes should be equal.

2. Using a vernier caliper, measure the distance between the crankshaft bearing cap edge and the crankshaft bearing edge.

Difference between (D) and (E):

0.5 mm (0.0197 in.) or less

NOTICE:

Do not apply engine oil to the crankshaft bearings or the contact surfaces.

9. INSTALL UPPER CRANKSHAFT THRUST WASHER

*a

Oil Grooves

-

-

(1) Install the 2 upper crankshaft thrust washers to the No. 3 journal position of the cylinder block sub-assembly with the oil grooves facing outward.

(2) Apply engine oil to the upper crankshaft thrust washers.

10. INSTALL CRANKSHAFT

(1) Apply engine oil to the upper crankshaft bearings and install the crankshaft to the cylinder block sub-assembly.

11. INSTALL CRANKSHAFT BEARING CAP

*a

Front Mark and Number

*b

Less than 5 mm

Front of Engine

-

-

(1) Apply engine oil to the lower crankshaft bearings.

(2) Confirm the front marks and numbers, and place the 5 crankshaft bearing caps on the cylinder block sub-assembly.

(3) Apply a light coat of engine oil to the threads and under the heads of the crankshaft bearing cap set bolts.

(4) Temporarily install the 10 crankshaft bearing cap set bolts.

(5) Push on the crankshaft bearing cap with your hand until the clearance between the crankshaft bearing cap and cylinder block sub-assembly is less than 5 mm (0.197 in.).

*a

Paint Mark

-

-

Front of Engine

-

-

(1) Using a plastic hammer, lightly tap the crankshaft bearing cap to ensure a proper fit.

(2) Install the crankshaft bearing cap set bolts.

NOTICE:

The crankshaft bearing cap set bolts are tightened in 2 progressive steps.

(3) Step 1

1. Install and uniformly tighten the 10 crankshaft bearing cap set bolts in the sequence shown in the illustration.

Torque:

40 N·m {408 kgf·cm, 30 ft·lbf}

HINT:

If a crankshaft bearing cap set bolt cannot be tightened to the specified torque, replace it.

(4) Step 2

1. Mark the front of the crankshaft bearing cap set bolts with paint.

2. Tighten the crankshaft bearing cap set bolts by 90° in the order shown in step 1.

(5) Check that the paint marks are now at a 90° angle.

(6) Check that the crankshaft turns smoothly.

(7) Check the crankshaft thrust clearance.

Click here

12. INSTALL CONNECTING ROD BEARING

*a

Vernier Caliper

-

-

(1) Install the 8 connecting rod bearings to the 4 connecting rods and 4 connecting rod caps.

(2) Using a vernier caliper, measure the distance between the edges of the connecting rod and connecting rod bearing, and the connecting rod cap and the connecting rod bearing.

Difference between (A) and (B):

0.7 mm (0.0276 in.) or less

NOTICE:

Do not apply engine oil to the connecting rod bearings or the contact surfaces.

13. INSTALL PISTON SUB-ASSEMBLY WITH CONNECTING ROD

*1

No. 1 Compression Ring and Oil Ring Expander

*2

No. 2 Compression Ring

*3

Upper Side Rail

*4

Lower Side Rail

*a

Front of Engine

-

-

(1) Apply engine oil to the cylinder walls, pistons, and surfaces of the connecting rod bearings.

(2) Position the piston ring set so that the ring ends are as shown in the illustration.

*a

Press around the circumference

*b

Ring End

*c

Correct

*d

Incorrect (Ends of the oil ring expander are overlapping)

*e

Front Mark

-

-

(1) Confirm that the ends of the oil ring expander are not overlapping and that the upper side rail and lower side rail are securely installed into the groove.

NOTICE:

  • After installing the oil ring expander, upper side rail and lower side rail, press around the circumference with a finger to check that they are securely installed into the groove.
  • If the oil ring expander is not securely installed into the groove, check that the ends of the oil ring expander are not overlapping.
  • If the ends of the oil ring expander are overlapping, remove the upper side rail and lower side rail and realign the oil ring expander using a screwdriver.

(2) Using a piston ring compressor, push the correctly numbered piston with connecting rod into the cylinder with the front marks of each piston sub-assembly with connecting rod facing the front of the engine.

NOTICE:

  • When inserting the piston sub-assembly with connecting rod, do not allow it to make contact with the No. 1 oil nozzle sub-assembly.
  • Match the numbered connecting rod cap with the connecting rod.

14. INSTALL CONNECTING ROD CAP

*a

Front Mark

*b

Paint Mark

Front of Engine

-

-

(1) Check that the front mark of the connecting rod cap is facing in the correct direction.

(2) Apply a light coat of engine oil to the threads and under the heads of the connecting rod bolts.

(3) Install the 8 connecting rod bolts.

NOTICE:

The connecting rod bolts are tightened in 2 progressive steps.

(4) Step 1

1. Using SST, alternately tighten the connecting rod bolts in several steps.

SST: 09205-16011

Torque:

20 N·m {204 kgf·cm, 15 ft·lbf}

(5) Step 2

1. Mark the front of the connecting rod bolts with paint.

2. Further tighten the connecting rod bolts 90° as shown in the illustration.

(6) Check that the paint marks are now at a 90° angle.

(7) Check that the crankshaft turns smoothly.

(1) Check the connecting rod thrust clearance.

Click here

15. INSTALL NO. 1 VENTILATION CASE

*A

Type A

*B

Type B

*a

Seal Packing

*b

2.0 to 3.0 mm

*c

5.0 mm

-

-

(1) Apply seal packing in a continuous line as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

Application Specification:

Seal Packing Diameter

Distance from Inside Edge of Cover to Center of Seal Packing

2.0 to 3.0 mm (0.0787 to 0.118 in.)

5.0 mm (0.197 in.)

NOTICE:

  • Remove any oil from the contact surfaces.
  • Install the No. 1 ventilation case within 3 minutes and tighten the bolts and nuts within 15 minutes of applying seal packing.
  • Do not start the engine for at least 2 hours after installation.

(2) Type A:

Install the No. 1 ventilation case with the 6 bolts and 2 nuts.

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

(3) Type B:

Install the No. 1 ventilation case with the 8 bolts.

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}