Rear Axle Hub (for 2wd)
- On-vehicle Inspection
- Removal
- Installation
On-vehicle Inspection
ON-VEHICLE INSPECTION
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear axle hub and bearing assembly on-Toyota Prius vehicle inspection are shown below.
Necessary Procedures After Parts Removed/Installed/ReplacedReplaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
| *1: Also necessary after performing a tire rotation. *2: It is not necessary to perform this procedure if the tire pressure warning valve and transmitters are installed to the same location. *3: The Toyota Prius vehicle height changes because of suspension or tire replacement. |
|||
Tires |
|
Tire Pressure Warning System |
Refer to Procedures Necessary When Replacing Parts (for Tire Pressure Warning System) |
Rear television camera assembly optical axis (Back camera position setting)*3 |
Parking Assist Monitor System |
||
Parking assist ECU initialization*3 |
Panoramic View Monitor System |
||
Advanced Park |
|||
HINT:
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when Toyota Prius vehicle is drivenEffect/Inoperative Function when Necessary Procedure not Performed | Necessary Procedure | Link |
|---|---|---|
Front Camera System |
Drive the Toyota Prius vehicle straight ahead at 35 km/h or more for 5 second or more. |
Effect/Inoperative Function when Necessary Procedure not Performed | Necessary Procedure | Link |
|---|---|---|
| *1: w/o Power Back Door System *2: w/ Power Back Door System |
||
Power Door Lock Control System*1
|
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. |
|
Power Back Door System*2 |
Reset back door close position |
|
Air Conditioning System |
for HEV Model:
|
- |
NOTICE:
- When removing or installing the rear disc brake caliper assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C140000 and/or C140A00 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure.
- While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.
- To prevent the key from being locked in the Toyota Prius vehicle, make sure to enter e-latch inspection mode and enable the manual release handle before disconnecting the cable from the negative (-) auxiliary battery terminal.
Click here

HINT:
- Use the same procedure for the RH and LH sides.
- The following procedure is for the LH side.
PROCEDURE
1. PRECAUTION
NOTICE:
- After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
Click here

- Make sure to read the precautions of the electric parking brake system before removing the rear brake assembly.
Click here

2. DISABLE BRAKE CONTROL
HINT:
Click here ![]()
3. REMOVE REAR WHEEL
HINT:
Click here ![]()
4. DISCONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY
HINT:
Click here ![]()
5. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY
HINT:
Click here ![]()
6. REMOVE REAR DISC
HINT:
Click here ![]()
7. INSPECT REAR AXLE HUB BEARING LOOSENESS
(a) Using a dial indicator with magnetic base, check for looseness near the center of the rear axle hub and bearing assembly. NOTICE:
|
![]() |
(b) If the looseness exceeds the maximum, replace the rear axle hub and bearing assembly.
8. INSPECT REAR AXLE HUB RUNOUT
(a) Using a dial indicator with magnetic base, check for runout on the surface of the rear axle hub and bearing assembly. NOTICE:
|
![]() |
(b) If the runout exceeds the maximum, replace the rear axle hub and bearing assembly.
9. INSTALL REAR DISC
HINT:
Click here ![]()
10. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY
HINT:
Click here ![]()
11. CONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY
HINT:
Click here ![]()
12. INSTALL REAR WHEEL
HINT:
Click here ![]()
13. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
HINT:
Click here ![]()
14. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL
HINT:
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click here ![]()
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear axle hub and bearing assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/ReplacedReplaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
| *1: Also necessary after performing a tire rotation. *2: It is not necessary to perform this procedure if the tire pressure warning valve and transmitters are installed to the same location. *3: The Toyota Prius vehicle height changes because of suspension or tire replacement. |
|||
Tires |
|
Tire Pressure Warning System |
Refer to Procedures Necessary When Replacing Parts (for Tire Pressure Warning System) |
Rear television camera assembly optical axis (Back camera position setting)*3 |
Parking Assist Monitor System |
||
Parking assist ECU initialization*3 |
Panoramic View Monitor System |
||
Advanced Park |
|||
HINT:
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when Toyota Prius vehicle is drivenEffect/Inoperative Function when Necessary Procedure not Performed | Necessary Procedure | Link |
|---|---|---|
Front Camera System |
Drive the Toyota Prius vehicle straight ahead at 35 km/h or more for 5 second or more. |
Effect/Inoperative Function when Necessary Procedure not Performed | Necessary Procedure | Link |
|---|---|---|
| *1: w/o Power Back Door System *2: w/ Power Back Door System |
||
Power Door Lock Control System*1
|
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. |
|
Power Back Door System*2 |
Reset back door close position |
|
Air Conditioning System |
for HEV Model:
|
- |
NOTICE:
- When removing or installing the rear disc brake caliper assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C140000 and/or C140A00 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure.
- While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.
- To prevent the key from being locked in the Toyota Prius vehicle, make sure to enter e-latch inspection mode and enable the manual release handle before disconnecting the cable from the negative (-) auxiliary battery terminal.
Click here

HINT:
- Use the same procedure for the RH and LH sides.
- The following procedure is for the LH side.

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
PRECAUTION |
- |
- |
- |
|
2 |
DISABLE BRAKE CONTROL |
- |
- |
- |
|
3 |
REAR WHEEL |
- |
- |
- |
- |
4 |
NO. 2 PARKING BRAKE WIRE ASSEMBLY |
890C0A |
- |
- |
|
5 |
REAR DISC BRAKE CALIPER ASSEMBLY |
- |
- |
- |
- |
6 |
REAR DISC |
42431 |
- |
- |
|
7 |
REAR AXLE HUB AND BEARING ASSEMBLY |
42450B |
- |
- |
- |
*1 |
REAR DISC BRAKE DUST COVER |
- |
- |
PROCEDURE
1. PRECAUTION
![]() |
NOTICE:
|
2. DISABLE BRAKE CONTROL
![]() |
Click here |
3. REMOVE REAR WHEEL
Click here ![]()
4. DISCONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY
![]() |
NOTICE:
|

(1) Disconnect the No. 2 parking brake wire assembly connector from the parking brake actuator assembly.
(2) Using a screwdriver with its tip wrapped in protective tape, disconnect the No. 2 parking brake wire assembly connector from the rear axle hub and bearing assembly.
NOTICE:
Be careful not to damage the rear axle hub and bearing assembly and connector cover.
5. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY
Click here ![]()
6. REMOVE REAR DISC
![]() |
Click here |
7. REMOVE REAR AXLE HUB AND BEARING ASSEMBLY

Installation
INSTALLATION
NOTICE:
- When removing or installing the rear disc brake caliper assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C140000 and/or C140A00 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure.
- While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.
- To prevent the key from being locked in the Toyota Prius vehicle, make sure to enter e-latch inspection mode and enable the manual release handle before disconnecting the cable from the negative (-) auxiliary battery terminal.
Click here

HINT:
- Use the same procedure for the RH and LH sides.
- The following procedure is for the LH side.

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
REAR AXLE HUB AND BEARING ASSEMBLY |
42450B |
- |
- |
- |
2 |
REAR AXLE HUB BEARING LOOSENESS |
- |
- |
- |
|
3 |
REAR AXLE HUB RUNOUT |
- |
- |
- |
|
4 |
REAR DISC |
42431 |
- |
- |
|
5 |
REAR DISC BRAKE CALIPER ASSEMBLY |
- |
- |
- |
- |
6 |
NO. 2 PARKING BRAKE WIRE ASSEMBLY |
890C0A |
- |
- |
|
7 |
REAR WHEEL |
- |
- |
- |
- |
8 |
CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL |
- |
- |
- |
|
9 |
INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL |
- |
- |
- |
|
10 |
CHECK FOR SPEED SENSOR SIGNAL |
- |
- |
- |
|
*1 |
REAR DISC BRAKE DUST COVER |
- |
- |
![]() |
Tightening torque for "Major areas involving basic Toyota Prius vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
- |
- |
PROCEDURE
1. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY
Torque:
90 N·m {918 kgf·cm, 66 ft·lbf}
2. INSPECT REAR AXLE HUB BEARING LOOSENESS
Click here
![]()
3. INSPECT REAR AXLE HUB RUNOUT
Click here
![]()
4. INSTALL REAR DISC
![]() |
Click here |
5. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY
Click here
![]()
6. CONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY
![]() |
NOTICE:
|

(1) Connect the No. 2 parking brake wire assembly connector to the parking brake actuator assembly.
(2) Connect the No. 2 parking brake wire assembly connector to the rear axle hub and bearing assembly.
7. INSTALL REAR WHEEL
Click here ![]()
8. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
![]() |
Click here |
9. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL
HINT:
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click here
![]()
10. CHECK FOR SPEED SENSOR SIGNAL
Click here ![]()








































