Cooler (for Phev Model)
- Removal
- Installation
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during No. 1 traction battery cooler conductor removal/installation are shown below.
CAUTION:
- Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

Click here

- To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.
Click here ![]()
HINT:
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Items for which learning is completed by driving the Toyota Prius vehicleEffect/Inoperative Function when Necessary Procedure not Performed | Necessary Procedure | Link |
|---|---|---|
Front Camera System |
Drive the Toyota Prius vehicle straight ahead at 35 km/h or more for 5 seconds or more. |
Effect/Inoperative Function when Necessary Procedure not Performed | Necessary Procedure | Link |
|---|---|---|
| *1: w/o Power Back Door System *2: w/ Power Back Door System |
||
Power Door Lock Control System*1
|
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. |
|
Power Back Door System*2 |
Reset back door close position |
|
Air Conditioning System |
After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. |
- |

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
HV SUPPLY STACK SUB-ASSEMBLY |
- |
- |
- |
- |
2 |
NO. 1 TRACTION BATTERY COOLER CONDUCTOR |
- |
- |
- |
- |
3 |
NO. 1 TRACTION BATTERY COOLER SHEET |
G96NA |
- |
- |
- |
*a |
Parts requiring replacement with new ones when replacing the No. 1 traction battery cooler conductor |
- |
- |
● |
Non-reusable part |
![]() |
Compressor oil ND-OIL 11 or equivalent |
PROCEDURE
1. REMOVE HV SUPPLY STACK SUB-ASSEMBLY
Click here ![]()
2. REMOVE NO. 1 TRACTION BATTERY COOLER CONDUCTOR

3. REMOVE NO. 1 TRACTION BATTERY COOLER SHEET

Installation
INSTALLATION
COMPONENTS (INSTALLATION)
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
NO. 1 TRACTION BATTERY COOLER SHEET |
G96NA |
- |
- |
|
2 |
NO. 1 TRACTION BATTERY COOLER CONDUCTOR |
- |
- |
- |
|
3 |
HV SUPPLY STACK SUB-ASSEMBLY |
- |
- |
- |
- |
*a |
Parts requiring replacement with new ones when replacing the No. 1 traction battery cooler conductor |
- |
- |
● |
Non-reusable part |
![]() |
Compressor oil ND-OIL 11 or equivalent |
PROCEDURE
1. INSTALL NO. 1 TRACTION BATTERY COOLER SHEET
![]() |
NOTICE:
|

*1 |
No. 1 Traction Battery Cooler Sheet |
*2 |
No. 1 Traction Battery Cooler Conductor |
*a |
394.1 to 400.9 mm (15.516 to 15.783 in.) |
*b |
23.5 mm (0.925 in.) |
*c |
Thermally Conduction Part |
*d |
Reference Point |
![]() |
Front of Toyota Prius Vehicle |
- |
- |
(1) Clean and degrease the surface of the new No. 1 traction battery cooler conductor.
(2) Attach the new No. 1 traction battery cooler sheet to the No. 1 traction battery cooler conductor in the position shown in the illustration.
2. INSTALL NO. 1 TRACTION BATTERY COOLER CONDUCTOR
![]() |
NOTICE: The No. 1 traction battery cooler conductor and No. 1 traction battery cooler sheet cannot be reused after removing and installing each HV supply stack sub-assembly. |

(1) Engage the 2 guides to install the No. 1 traction battery cooler conductor.
(2) Fill the No. 1 traction battery cooler conductor with the included compressor oil.
Required Amount(HINT):
10 g (0.353 oz)
3. INSTALL HV SUPPLY STACK SUB-ASSEMBLY
Click here ![]()
















