Fuel Lid Opener System

In this manual: Fuel Lid Opener System
How To Troubleshoot Ecu Controlled Systems — 1How To Use This Manual — 1Identification Information — 1Repair Instruction — 1Terms — 12zr-fxe Air Cleaner Filter Element — 12zr-fxe Auxiliary Battery — 12zr-fxe Coolant (for Engine Coolant) — 12zr-fxe Oil And Oil Filter — 12zr-fxe Spark Plug — 1Air Conditioning Filter — 1Battery Cooling Filter — 1Brake Fluid — 1Coolant (for Inverter) — 1Front Brake Flexible Hose — 1Front Disc Brake Pad — 1Front Lower Ball Joint — 1Front Wheel Alignment — 1Front Wiper Rubber — 1General Maintenance — 1M20a-fxs Air Cleaner Filter Element — 1M20a-fxs Auxiliary Battery — 1M20a-fxs Coolant (for Engine Coolant) — 1M20a-fxs Oil And Oil Filter — 1M20a-fxs Spark Plug — 1Pa10/pb10/pb12 Hybrid Transaxle Fluid — 1Q810 Hybrid Transaxle Fluid — 1Rear Brake Flexible Hose — 1Rear Disc Brake Pad — 1Rear Wheel Alignment — 1Steering Column — 1Tire And Wheel — 1Transmitter Battery — 1When Disconnecting Or Reconnecting Battery Terminal — 1When Replacing Or Removing/installing Parts — 1Automatic High Beam Main Switch — 1Automatic High Beam System — 1Driver Monitor Camera — 1Driver Monitor Camera System — 1Driver Monitor Ecu — 1Front Camera — 1Front Camera System — 1Front Radar Sensor System — 1Front Side Radar Sensor — 1Front Side Radar Sensor System — 1Millimeter Wave Radar Sensor — 1Utility — 1Advanced Park — 1Advanced Park Main Switch — 1Amplifier Antenna — 1Audio And Visual System — 1Front Door Speaker — 1Instrument Panel Speaker — 1Microphone — 1Noise Filter — 1Pillar Speaker — 1Radio Antenna Cord (for Back Door) — 1Radio Antenna Cord (for Instrument Panel) — 1Radio Antenna Cord (for Roof) — 1Radio Receiver — 1Rear Door Speaker — 1Roof Antenna — 1Stereo Component Amplifier — 1Stereo Jack Adapter Assembly — 1Window Glass Antenna Wire — 1Back-up Battery — 1Dcm(telematics Transceiver) — 1Manual(sos)switch — 1Safety Connect System — 1Telephone And Gps Antenna (for Front Side) — 1Telephone And Gps Antenna (for Roof Side) — 1Telephone And Gps Antenna Cords — 1Garage Door Opener System (for Digital Inner Mirror) — 1Garage Door Opener System (for Ec Inner Mirror) — 1Blind Spot Monitor Sensor — 1Blind Spot Monitor System — 1Clearance Warning Ecu — 1Intuitive Parking Assist System — 1Panoramic View Monitor Switch — 1Panoramic View Monitor System — 1Parking Assist Ecu — 1Parking Assist Light — 1Parking Assist Monitor System — 1Parking Support Brake System — 1Rear View Monitor System — 1Television Camera (for Front) — 1Television Camera (for Rear) — 1Television Camera (for Side) — 1Ultrasonic Sensor (for Front) — 1Ultrasonic Sensor (for Rear) — 1Brake Actuator — 1Brake Pedal Stroke Sensor — 1Electronically Controlled Brake System — 1Front Speed Sensor — 1Rear Speed Sensor (for Awd) — 1Steering Angle Sensor — 1Brake Booster — 1Brake Fluid — 1Brake Line — 1Brake Pedal — 1Brake System — 1Electric Parking Brake Actuator — 1Electric Parking Brake Switch — 1Electric Parking Brake System — 1Forced Release — 1Front Axle Hub — 1Front Axle Hub Bolt — 1Rear Axle Carrier (for 2wd) — 1Rear Axle Carrier (for Awd) — 1Rear Axle Hub (for 2wd) — 1Rear Axle Hub (for Awd) — 1Rear Axle Hub Bolt — 1Steering Knuckle — 1Drive Shaft System — 1Front Drive Shaft Assembly — 1Rear Drive Shaft Assembly — 1Combination Switch — 1Electronic Shift Lever System — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Oil Seal — 1Hybrid Transaxle System — 1Input Shaft Oil Seal — 1Motor Cable — 1Pa10 Hybrid Vehicle Transaxle — 1Pa10 Manual Parking Lock Release — 1Pa10 Oil Cooler — 1Pb10/pb12 Hybrid Vehicle Transaxle — 1Pb10/pb12 Manual Parking Lock Release — 1Pb10/pb12 Oil Cooler — 1Shift Control Actuator — 1Shift Lever — 1Shift Lever Knob — 1Differential Side Gear Shaft — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Side Gear Oil Seal — 1Motor Cable — 1Rear Traction Motor — 1Coolant (for Engine) — 1Cooling Fan Motor — 1Cooling Fan System — 1Radiator — 1Relay — 1Thermostat — 1Water Pump — 1Canister — 1Egr Cooler — 1Egr Valve — 1Emission Control System — 1Fuel Tank Cap — 1Pcv Valve — 1Purge Valve — 1Vacuum Sensor — 1Air Fuel Ratio Sensor — 1Camshaft Oil Control Valve — 1Camshaft Position Sensor — 1Crankshaft Position Sensor — 1Ecm — 1Engine Coolant Temperature Sensor — 1Heated Oxygen Sensor — 1Ignition Coil And Spark Plug — 1Ignition System — 1Knock Sensor — 1Mass Air Flow Meter — 1Relay — 1Sfi System — 1Throttle Body — 1Camshaft — 1Cylinder Block — 1Cylinder Head — 1Cylinder Head Gasket — 1Engine — 1Engine Assembly — 1Engine Unit — 1Front Crankshaft Oil Seal — 1Rear Crankshaft Oil Seal — 1Fuel Filter — 1Fuel Injector — 1Fuel Pressure Regulator — 1Fuel Pump — 1Fuel Sender Gauge Assembly — 1Fuel System — 1Fuel Tank — 1Air Cleaner Filter Element — 1Exhaust Manifold — 1Exhaust Pipe — 1Intake Manifold — 1Intake System — 1Lubrication System — 1Oil And Oil Filter — 1Oil Pan And Oil Level Sensor — 1Oil Pressure Switch — 1Oil Pump — 1Accelerator Pedal Sensor — 1Battery Blower (for Hev Model) — 1Battery Ecu (for Hev Model) — 1Battery Ecu (for Phev Model) — 1Battery Voltage Sensor (for Phev Model) — 1Charge Cable (for Phev Model) — 1Charge Indicator (for Phev Model) — 1Charge Inlet (for Phev Model) — 1Combination Switch — 1Coolant (for Inverter) — 1Cooler (for Phev Model) — 1Electric Vehicle Charger Assembly (for Phev Model) — 1Frame Wire (for Hev Model) — 1Frame Wire (for Phev Model) — 1Heater Relay (for Phev Model) — 1Hv Battery (for Hev Model) — 1Hv Battery (for Phev Model) — 1Hv Battery Heater (for Phev Model) — 1Hv Battery Stack (for Phev Model) — 1Hv Relay Assembly (for Hev Model) — 1Hv Relay Assembly (for Phev Model) — 1Hybrid Battery System (for 2zr-fxe) — 1Hybrid Battery System (for M20a-fxs) — 1Hybrid Battery System (for Phev Model) — 1Hybrid Vehicle Control Ecu — 1Inverter With Converter (for Hev Model) — 1Motor Generator Control System (for 2zr-fxe) — 1Plug-in Charge Control System (for Phev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Service Plug Grip (for Hev Model) — 1Sub Radiator — 1Water Pump With Motor — 1Auxiliary Battery — 1Battery Current Sensor — 1Charging System — 1Solar Charging System — 1Solar Control Unit — 1Solar Roof — 1Can Communication System (for Hev Model) — 1Lin Communication System — 1Network Gateway Ecu — 1Integration Control Supply — 1Main Body Ecu — 1Power Integration System — 1Sub Battery System — 1Power Steering Ecu — 1Power Steering System — 1Heated Steering Wheel Controller — 1Heated Steering Wheel System — 1Steering Column Assembly — 1Steering Heater Switch — 1Steering Pad Switch — 1Steering System — 1Steering Wheel — 1Front Lower Ball Joint — 1Front Lower Suspension Arm (for 2zr-fxe Lh Side) — 1Front Lower Suspension Arm (for 2zr-fxe Rh Side) — 1Front Lower Suspension Arm (for M20a-fxs) — 1Front Shock Absorber — 1Front Stabilizer Bar — 1Front Suspension Member — 1Rear Coil Spring — 1Rear Lower Arm (for Awd Lh Side) — 1Rear Lower Arm (for Awd Rh Side) — 1Rear Lower Arm (for Hev Model 2wd) — 1Rear Lower Arm (for Phev Model) — 1Rear Shock Absorber — 1Rear Stabilizer Bar — 1Rear Suspension Member (for 2wd) — 1Rear Suspension Member (for Awd) — 1Rear Trailing Arm — 1Rear Upper Arm — 1Tire And Wheel System — 1Tire Repair Seal — 1Tire Pressure Warning Receiver — 1Tire Pressure Warning System — 1Tire Pressure Warning Valve — 1Acoustic Vehicle Alerting System — 1Vehicle Approaching Speaker — 1Vehicle Approaching Speaker Ecu — 1Back Door — 1Back Door Closer Ecu — 1Back Door Opener Switch — 1Back Door Support — 1Back Door Weatherstrip — 1Charge Lid Courtesy Switch — 1Charge Lid Opener Motor Assembly — 1Charge Lid Opener System — 1Charge Lid Opener Unit — 1Front Door — 1Front Door Opening Trim Weatherstrip — 1Fuel Lid Opener Motor Assembly — 1Fuel Lid Opener Switch — 1Fuel Lid Opener System — 1Hood — 1Hood Lock Control Cable Assembly — 1Power Back Door Closer Switch — 1Power Back Door Control Switch — 1Power Back Door Drive Unit — 1Power Back Door System — 1Power Back Door Touch Sensor — 1Power Back Door Warning Buzzer — 1Rear Door — 1Rear Door Opening Trim Weatherstrip — 1Reserve Lock Switch — 1Front Bumper — 1Front Door Belt Moulding — 1Front Door Window Frame Moulding — 1Front Fender — 1Front Pillar Upper Cover — 1Grille Shutter — 1Grille Shutter System — 1Name Plate — 1Quarter Garnish — 1Rear Bumper — 1Rear Door Belt Moulding — 1Rear Door Window Frame Moulding — 1Rear Wheel House Plate — 1Rocker Panel Moulding — 1Roof Drip Side Finish Moulding — 1Roof Garnish — 1Wheel Opening Moulding (for Front Side) — 1Wheel Opening Moulding (for Rear Side) — 1Windshield Outside Moulding — 1Horn — 1Horn System — 1Relay — 1Automatic Light Control Sensor — 1Back-up Light Assembly — 1Charge Lid Light — 1Front Marker Light — 1Hazard Warning Switch — 1Headlight Assembly — 1Headlight Dimmer Switch — 1Headlight Leveling Switch — 1High Mounted Stop Light Assembly — 1Illumination Light Assembly — 1License Plate Light Assembly — 1Lighting System — 1Rear Combination Light Assembly — 1Rear Light Assembly — 1Rear Side Marker Light Assembly — 1Relay — 1Side Turn Signal Light Assembly — 1Stop Light Switch — 1Switch Housing — 1Outer Mirror Switch — 1Outer Rear View Mirror — 1Outer Rear View Mirror Cover — 1Outer Rear View Mirror Glass — 1Power Mirror Control System — 1Back Door Glass — 1Front Passenger Side Power Window Switch — 1Power Window Control System — 1Power Window Master Switch — 1Power Window Regulator Motor (for Front Door) — 1Power Window Regulator Motor (for Rear Door) — 1Rear Power Window Switch — 1Relay — 1Roof Window Fix Glass — 1Window Defogger System — 1Windshield Deicer Switch — 1Windshield Deicer System — 1Windshield Glass — 1Front Wiper Motor — 1Rain Sensor — 1Relay — 1Washer Motor — 1Washer Nozzle (for Front Side) — 1Washer Nozzle (for Rear Television Camera) — 1Wiper And Washer System — 1Wiper Ecu — 1Wiper Switch — 1Back Door Lock — 1Door Control Receiver — 1Door Control Switch — 1Door Control Transmitter — 1Door Lock Release Motor (for Rear Side) — 1Door Outside Handle (for Rear Side) — 1Front Door Lock — 1Power Door Lock Control System — 1Rear Door Lock — 1Transmitter Battery — 1Wireless Door Lock Control System — 1Accumulator — 1Air Conditioning Amplifier — 1Air Conditioning Panel — 1Air Conditioning Pressure Sensor — 1Air Conditioning Unit — 1Ambient Temperature Sensor — 1Blower Unit — 1Condenser (for Hev Model) — 1Condenser (for Phev Model) — 1Discharge Temperature Sensor — 1Electric Expansion Valve (cooling) — 1Electric Expansion Valve (heating) — 1Evaporator Pipe Temperature Sensor — 1Evaporator Pressure Regulator — 1Front Blower Motor — 1Front Evaporator Front Solenoid Valve — 1Air Conditioning System (for Hev Model) — 1Front Evaporator Temperature Sensor — 1Heat Exchanger Temperature Sensor — 1Heat Pump Ecu — 1High Pressure Magnetic Valve — 1Humidity Sensor — 1Internal Condenser Temperature Sensor — 1Low Pressure Magnetic Valve — 1Refrigerant (for Hfc-134a(r134a)) — 1Refrigerant Line (for Hev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Room Temperature Sensor — 1Solar Sensor — 1Floor Carpet — 1Front Console Box — 1Instrument Panel Safety Pad — 1Roof Headlining — 1Roof Sunshade — 1Ambient Light (for Driver Side) — 1Ambient Light (for Front Passenger Side) — 1Back Door Courtesy Switch — 1Footwell Light — 1Glove Box Light — 1Lighting System — 1Luggage Compartment Room Light — 1Personal Light — 1Room Light — 1Vanity Light — 1Vanity Light Switch — 1Combination Meter — 1Meter / Gauge System — 1Trip Switch — 1Digital Inner Mirror — 1Digital Rear-view Mirror System — 1Inner Mirror Monitor Camera — 1Inner Rear View Mirror (w/o Ec Mirror) — 1Accessory Power Outlet System — 1Power Outlet Socket (for Console Box Front Side) — 1Power Outlet Socket (for Console Box Rear Side) — 1Power Outlet Socket (for Console Box) — 1Power Outlet Socket (for Luggage Compartment) — 1Power Outlet Switch — 1Wireless Charger Assembly — 1Wireless Charging System — 1Climate Control Seat System — 1Front Power Seat Control System (w/ Memory) — 1Front Power Seat Motor Assembly — 1Front Seat Assembly (for Power Seat) — 1Front Seat Cushion Heater (for Power Seat) — 1Front Seatback Heater (for Power Seat) — 1Lumbar Support Adjuster Assembly — 1Power Seat Control Ecu — 1Power Seat Switch — 1Power Seat Track Rail Assembly — 1Rear Seat Assembly — 1Rear Seat Cushion Heater — 1Rear Seat Reminder System — 1Rear Seatback Heater — 1Seat Heater Control — 1Seat Heater Switch (for Front Seat) — 1Seat Heater Switch (for Rear Side) — 1Seat Heater System — 1Seat Memory Switch — 1Child Restraint Seat Anchor Bracket — 1Front Seat Inner Belt Assembly — 1Front Seat Outer Belt Assembly — 1Occupant Detection Sensor (for Front Passenger Side) — 1Rear Center Seat Outer Belt Assembly — 1Rear Seat Inner Belt Assembly (for Rh Side) — 1Rear Seat Outer Belt Assembly — 1Seat Belt Warning System (w/ Occupant Classification System) — 1Tongue Plate Stopper — 1Airbag System — 1Center Airbag Sensor Assembly — 1Curtain Shield Airbag Assembly — 1Front Airbag Sensor — 1Front Passenger Airbag Assembly — 1Front Seat Side Airbag Assembly — 1Inspection After Collision — 1Knee Airbag Assembly — 1Occupant Classification System — 1Rear Seat Side Airbag Assembly — 1Side Airbag Sensor (for Center Pillar) — 1Side Airbag Sensor (for Front Door) — 1Spiral Cable — 1Steering Pad — 1Certification Ecu — 1Digital Key Ecu — 1Digital Key Receiver (for Front Floor) — 1Digital Key Receiver (for Outside Luggage Compartment) — 1Digital Key Receiver (for Rear Door) — 1Digital Key System — 1Electrical Key Oscillator (for Front Floor) — 1Electrical Key Oscillator (for Outside Luggage Compartment) — 1Electrical Key Oscillator (for Rear Floor) — 1Engine Hood Courtesy Switch — 1Id Code Box — 1Smart Key System (for Start Function) — 1
~23min read
  • Precaution
  • Parts Location
  • System Diagram
  • System Description
  • How To Proceed With Troubleshooting
  • Operation Check
  • Problem Symptoms Table
  • Terminals Of Ecu
  • Data List / Active Test
  • Fuel Lid Opener does not Operate

Precaution

PRECAUTION

PRECAUTIONS FOR DISCONNECTING CABLE FROM NEGATIVE (-) AUXILIARY BATTERY TERMINAL

NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click here

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click here

PRECAUTIONS FOR REMOVAL, INSTALLATION AND REPLACEMENT OF COMPONENTS

(a) After replacing certain components, it may be necessary to update the ECU security key.

Click here

Parts Location

PARTS LOCATION

ILLUSTRATION

*A

for M20A-FXS

*B

for 2ZR-FXE

*1

FUEL LID OPENER SWITCH

*2

DLC3

*3

POWER DISTRIBUTION BOX ASSEMBLY

- FUEL OPN FUSE

- FUEL OPN RELAY/FUEL LOCK RELAY

*4

ECM

*5

NO.1 ENGINE ROOM RELAY BLOCK AND NO.1 JUNCTION BLOCK ASSEMBLY

- EFI NO.3 FUSE

*6

FUEL LID WITH MOTOR LOCK ASSEMBLY

- FUEL LID COURTESY SWITCH

*7

FUEL LID WITH MOTOR LOCK ASSEMBLY

*8

COMBINATION METER ASSEMBLY

System Diagram

SYSTEM DIAGRAM

System Description

SYSTEM DESCRIPTION

for M20A-FXS

When the fuel lid opener switch is operated, the pressure in the fuel tank is decreased and a message is displayed on the multi-information display. After the pressure has decreased, the ECM turns on the FUEL OPN relay/FUEL LOCK relay to operate the fuel lid with motor lock assembly to open the fuel lid. When the fuel lid is opened, a fuel lid courtesy switch signal is output and a message is displayed on the multi-information display.

for 2ZR-FXE

When the fuel lid opener switch is operated, the fuel lid with motor lock assembly opens the fuel lid.

How To Proceed With Troubleshooting

HINT:

  • Use the following procedure to troubleshoot the fuel lid opener system.
  • *: Use the GTS.

PROCEDURE

  1. Toyota Prius Vehicle BROUGHT TO WORKSHOP

NEXT
  1. CUSTOMER PROBLEM ANALYSIS

HINT:

  • In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
  • Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
  • The following 5 items are important points for problem analysis:

    What

    Toyota Prius Vehicle model, system name

    When

    Date, time, occurrence frequency

    Where

    Road conditions

    Under what conditions?

    Driving conditions, weather conditions

    How did it happen?

    Problem symptoms

NEXT
  1. INSPECT AUXILIARY BATTERY VOLTAGE

(a) Measure the auxiliary battery voltage with the ignition switch off.

Standard voltage:

11 to 14 V

HINT:

  • A simple method to determine whether the auxiliary battery is discharged is to operate the horn.
  • If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding.

(b) Check the fuses and relays.

(c) Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.

NEXT
  1. SYSTEM CHECK

(a) Check the Toyota Prius vehicle specification.

Result

Proceed to

for M20A-FXS

A

for 2ZR-FXE

B

B

GO TO STEP 6

A
  1. CHECK FOR DTC*

(a) Clear the DTCs.

Powertrain > Engine > Clear DTCs

(b) Check for SFI system DTCs.

Powertrain > Engine > Trouble Codes

OK:

SFI system DTCs are not output.

NG

GO TO SFI SYSTEM

OK
  1. PROBLEM SYMPTOMS TABLE

(a) Refer to Problem Symptoms Table.

Click here

Result

Proceed to

Fault is not listed in Problem Symptoms Table

A

Fault is listed in Problem Symptoms Table

B

B

ADJUST, REPAIR OR REPLACE IN ACCORDANCE WITH PROBLEM SYMPTOMS TABLE

A
  1. OVERALL ANALYSIS AND TROUBLESHOOTING*

(a) Data List / Active Test

Click here

(b) Operation Check

Click here

(c) Terminals of ECU

Click here

(d) Inspection

NEXT
  1. REPAIR OR REPLACE

NEXT
  1. CONFIRMATION TEST

NEXT

END

Operation Check

OPERATION CHECK

CHECK FUEL LID OPENER SYSTEM

(a) Push the fuel lid opener switch and check that messages are displayed on the multi-information display in the combination meter assembly and the fuel lid opens.*1

(b) Push the fuel lid opener switch and check that the fuel lid opens.*2

  • *1: for M20A-FXS
  • *2: for 2ZR-FXE

Problem Symptoms Table

PROBLEM SYMPTOMS TABLE

NOTICE:

  • When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the Toyota Prius vehicle and a DTC may be stored.
  • After replacing combination meter assembly, it may be necessary to update the ECU security key.

    Click here

HINT:

  • If a malfunction occurs in the close tank valve assembly or vapor pressure sensor, the fuel lid opener does not operate due to ECM control.
  • If the fuel lid opener operates after a short time, the close tank valve assembly or fuel tank vent hose may be clogged.
Fuel Lid Opener System (for M20A-FXS)

Symptom

Suspected Area

Link

Fuel lid opener does not operate

Proceed to "Fuel Lid Opener does not Operate"

Messages are not displayed on the multi-information display in the combination meter assembly

Harness or connector

-

Combination meter assembly

ECM

Fuel Lid Opener System (for 2ZR-FXE)

Symptom

Suspected Area

Link

Fuel lid opener does not operate

Proceed to "Fuel Lid Opener does not Operate"

Terminals Of Ecu

TERMINALS OF ECU

CHECK ECM (for M20A-FXS)

HINT:

The standard voltage and waveform between each pair of the ECM terminals are shown in the table below. The appropriate conditions for checking each pair of the terminals is also indicated. The result of checks should be compared with the standard voltage, resistance and waveform for each pair of the terminals as displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

A92-31 (LIDO) - A92-10 (E1)

Fuel lid with motor lock assembly (fuel lid courtesy switch) signal

Fuel lid closed

Below 1 V

Fuel lid open

11 to 14 V

A92-38 (FUEL) - A92-10 (E1)

Fuel lid opener switch signal

fuel lid opener switch pressed

Below 1 V

fuel lid opener switch not pressed

11 to 14 V

A92-41 (LSTM) - A92-10 (E1)

Fuel lid operation signal for combination meter assembly

"Close Fuel Lid" displayed on multi-information display

Pulse generation

(see waveform 1)

"Ready to Refuel" displayed on multi-information display

Pulse generation

(see waveform 2)

"Please Wait Fuel Door Opening" displayed on multi-information display

Pulse generation

(see waveform 3)

A92-44 (FREL) - A92-10 (E1)

Fuel lid with motor lock assembly operation signal

Fuel lid with motor lock assembly operating

Below 1 V

Fuel lid with motor lock assembly not operating

11 to 14 V

(a) Using an oscilloscope, check waveform 1.

Waveform 1 (Reference)

Item

Content

Terminal No. (Symbol)

A92-41 (LSTM) - A92-10 (E1)

Tool Setting

5 V/DIV., 20 ms./DIV.

Condition

"Close Fuel Lid" displayed on multi-information display

HINT:

This waveform is output when the fuel lid opener switch is operated if the fuel lid is open and any of the following conditions are met:

  • The Toyota Prius vehicle has been driven for 1 km (0.6 mile) or more at a speed of 50 km/h or more.
  • 30 minutes or more have elapsed since the fuel lid opener switch was operated.

(b) Using an oscilloscope, check waveform 2.

Waveform 2 (Reference)

Item

Content

Terminal No. (Symbol)

A92-41 (LSTM) - A92-10 (E1)

Tool Setting

5 V/DIV., 20 ms./DIV.

Condition

"Ready to Refuel" displayed on multi-information display

(c) Using an oscilloscope, check waveform 3.

Waveform 3 (Reference)

Item

Content

Terminal No. (Symbol)

A92-41 (LSTM) - A92-10 (E1)

Tool Setting

5 V/DIV., 20 ms./DIV.

Condition

"Please Wait Fuel Door Opening" displayed on multi-information display

HINT:

This waveform is output when the internal pressure of the fuel tank is higher than the ambient pressure when the fuel lid opener switch is operated.

CHECK ECM (for 2ZR-FXE)

HINT:

The standard voltage and waveform between each pair of the ECM terminals are shown in the table below. The appropriate conditions for checking each pair of the terminals is also indicated. The result of checks should be compared with the standard voltage, resistance and waveform for each pair of the terminals as displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

A91-60 (FUEL) - A91-17 (E1)

Fuel lid opener switch signal

fuel lid opener switch pressed

Below 1 V

fuel lid opener switch not pressed

11 to 14 V

A91-28 (FREL) - A91-17 (E1)

Fuel lid with motor lock assembly operation signal

Fuel lid with motor lock assembly operating

Below 1 V

Fuel lid with motor lock assembly not operating

11 to 14 V

CHECK COMBINATION METER ASSEMBLY (for M20A-FXS)

(a) Disconnect the K18 combination meter assembly connector.

(b) Measure the voltage and resistance according to the value(s) in the table below.

Terminal No.

Terminal Description

Condition

Specified Condition

K18-5 (B) - Body ground

Auxiliary battery

Ignition switch off

11 to 14 V

K18-6 (IG ) - Body ground

Ignition switch signal

Ignition switch off

Below 1 V

Ignition switch ON

11 to 14 V

K18-1 (EP) - Body ground

Ground

Always

Below 1 Ω

K18-2 (ES) - Body ground

Ground

Always

Below 1 Ω

(c) Reconnect the K18 combination meter assembly connector.

(d) Measure the waveform according to the value(s) in the table below.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

K18-28 (LST1) - Body ground

Fuel lid operation signal for combination meter assembly

"Close Fuel Lid" displayed on multi-information display

Pulse generation

(see waveform 1)

"Ready to Refuel" displayed on multi-information display

Pulse generation

(see waveform 2)

"Please Wait Fuel Door Opening" displayed on multi-information display

Pulse generation

(see waveform 3)

(1) Using an oscilloscope, check waveform 1.

Waveform 1 (Reference)

Item

Content

Terminal No. (Symbol)

K18-28 (LST1) - Body ground

Tool Setting

5 V/DIV., 20 ms./DIV.

Condition

"Close Fuel Lid" displayed on multi-information display

HINT:

This waveform is output when the fuel lid opener switch is operated if the fuel lid is open and any of the following conditions are met:

  • The Toyota Prius vehicle has been driven for 1 km (0.6 mile) or more at a speed of 50 km/h or more.
  • 30 minutes or more have elapsed since the fuel lid opener switch was operated.

(2) Using an oscilloscope, check waveform 2.

Waveform 2 (Reference)

Item

Content

Terminal No. (Symbol)

K18-28 (LST1) - Body ground

Tool Setting

5 V/DIV., 20 ms./DIV.

Condition

"Ready to Refuel" displayed on multi-information display

(3) Using an oscilloscope, check waveform 3.

Waveform 3 (Reference)

Item

Content

Terminal No. (Symbol)

K18-28 (LST1) - Body ground

Tool Setting

5 V/DIV., 20 ms./DIV.

Condition

"Please Wait Fuel Door Opening" displayed on multi-information display

HINT:

This waveform is output when the internal pressure of the fuel tank is higher than the ambient pressure when the fuel lid opener switch is operated.

Data List / Active Test

DATA LIST / ACTIVE TEST

DATA LIST

HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

(a) According to the display on the GTS, read the "Data List".

Powertrain > Engine > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Fuel Filler Opener

Fuel lid with motor lock assembly status

OFF or ON

OFF: Fuel lid with motor lock assembly not operating

ON: Fuel lid with motor lock assembly operating

for M20A-FXS

Fuel Lid SW

Fuel lid opener switch status

Close or Open

Close: Fuel lid opener switch not pushed

Open: Fuel lid opener switch pushed

-

Fuel Lid Sensor SW

Fuel lid with motor lock assembly (fuel lid courtesy switch) status

Close or Open

Close: Fuel lid closed

Open: Fuel lid open

for M20A-FXS

ACTIVE TEST

HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) According to the display on GTS perform the "Active Test".

Powertrain > Engine > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Activate the Fuel Filler Opener

Activate fuel lid with motor lock assembly

OFF or ON

for M20A-FXS

Fuel Lid Opener does not Operate

DESCRIPTION

When the fuel lid opener switch is pushed, a fuel lid opener switch signal is sent to the ECM. The ECM turns on the FUEL OPN relay/FUEL LOCK relay and the fuel lid with motor lock assembly opens the fuel lid. When the fuel lid is open, a fuel lid courtesy switch signal is output from the fuel lid with motor lock assembly.

WIRING DIAGRAM

for M20A-FXS

for 2ZR-FXE

HINT:

  • Inspect the fuses for circuits related to this system before performing the following procedure.
  • If a malfunction occurs in the close tank valve assembly or vapor pressure sensor, the fuel lid opener does not operate due to ECM control.
  • If the fuel lid opener operates after a short time, the close tank valve assembly or fuel tank vent hose may be clogged.

PROCEDURE

  1. CONFIRM MODEL

(a) Choose the model to be inspected.

Result

Proceed to

for M20A-FXS

A

for 2ZR-FXE

B

B

GO TO STEP 16

A
  1. CHECK FOR DTC

(a) Using the GTS, check that DTCs related to the close tank valve assembly or vapor pressure sensor are not output.

Powertrain > Engine > Trouble Codes

Result

Proceed to

DTCs related to the close tank valve assembly or vapor pressure sensor are not output

A

DTCs related to the close tank valve assembly or vapor pressure sensor are output

B

B

GO TO RELEVANT DIAGNOSTIC TROUBLE CODE PROCEDURE

A
  1. PERFORM ACTIVE TEST USING GTS

(a) Perform the Active Test according to the display on the GTS.

Powertrain > Engine > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Activate the Fuel Filler Opener

Activate fuel lid with motor lock assembly

OFF or ON

-

Powertrain > Engine > Active Test

Activate the Fuel Filler Opener

OK:

The fuel lid with motor lock assembly operates normally.

NG

GO TO STEP 11

OK
  1. READ VALUE USING GTS (Fuel Lid SW)

(a) Enter the following menus: Powertrain / Engine / Data List.

(b) Read the Data List according to the display on the GTS.

Powertrain > Engine > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Fuel Lid SW

Fuel lid opener switch status

Close or Open

Close: Fuel lid opener switch not pushed

Open: Fuel lid opener switch pushed

-

Powertrain > Engine > Data List

Fuel Lid SW

OK:

The GTS display changes correctly in response to the operation of the fuel lid opener switch.

NG

GO TO STEP 9

OK
  1. READ VALUE USING GTS (FUEL LID SENSOR SW)

(a) Read the Data List according to the display on the GTS.

Powertrain > Engine > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Fuel Lid Sensor SW

Fuel lid courtesy switch status

Close or Open

Close: Fuel lid closed

Open: Fuel lid open

-

Powertrain > Engine > Data List

Fuel Lid Sensor SW

OK:

The GTS display changes correctly in response to the operation of the fuel lid courtesy switch (fuel lid with motor lock assembly).

NG

GO TO STEP 7

OK
  1. CHECK CLOSE TANK VALVE ASSEMBLY OR FUEL TANK VENT HOSE

(a) Check the close tank valve assembly or fuel tank vent hose for clogging.

Click here

OK:

The close tank valve assembly or fuel tank vent hose is not clogged.

OK

REPLACE ECM

NG

REMOVE THE CLOGGING

  1. INSPECT FUEL LID WITH MOTOR LOCK ASSEMBLY (FUEL LID COURTESY SWITCH)

(a) Remove the fuel lid with motor lock assembly.

Click here

(b) Inspect the fuel lid with motor lock assembly.

Click here

NG

REPLACE FUEL LID LOCK WITH MOTOR ASSEMBLY

OK
  1. CHECK HARNESS AND CONNECTOR (FUEL LID WITH MOTOR LOCK ASSEMBLY - ECM)

(a) Disconnect the A92 ECM connector.

(b) Disconnect the R37 fuel lid with motor lock assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(R37,A92) Click Connector(R37) Click Connector(A92)

Tester Connection

Condition

Specified Condition

R37-3 (B) - A92-31 (LIDO)

Always

Below 1 Ω

R37-3 (B) or A92-31 (LIDO) - Body ground

Always

10 kΩ or higher

OK

REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. INSPECT FUEL LID OPENER SWITCH

(a) Remove the fuel lid opener switch.

Click here

(b) Inspect the fuel lid opener switch.

Click here

NG

REPLACE FUEL LID OPENER SWITCH

OK
  1. CHECK HARNESS AND CONNECTOR (FUEL LID OPENER SWITCH - ECM AND BODY GROUND)

(a) Disconnect the A92 ECM connector.

(b) Disconnect the K50 fuel lid opener switch connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(K50,A92) Click Connector(K50) Click Connector(A92)

Tester Connection

Condition

Specified Condition

K50-5 (IG) - A92-38 (FUEL)

Always

Below 1 Ω

K50-5 (IG) or A92-38 (FUEL) - Body ground

Always

10 kΩ or higher

K50-2 (E) - Body ground

Always

Below 1 Ω

OK

REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. INSPECT FUEL LID WITH MOTOR LOCK ASSEMBLY (MOTOR OPERATION)

(a) Remove the fuel lid with motor lock assembly.

Click here

(b) Inspect the fuel lid with motor lock assembly.

Click here

NG

REPLACE FUEL LID WITH MOTOR LOCK ASSEMBLY

OK
  1. CHECK HARNESS AND CONNECTOR (FUEL LID WITH MOTOR LOCK ASSEMBLY - POWER DISTRIBUTION BOX ASSEMBLY AND BODY GROUND)

(a) Disconnect the R37 fuel lid with motor lock assembly connector.

(b) Disconnect the R17 power distribution box assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(R37,R17) Click Connector(R37) Click Connector(R17)

Tester Connection

Condition

Specified Condition

R37-1 (B) - R17-29

Always

Below 1 Ω

R37-2 (E) - Body ground

Always

Below 1 Ω

R37-1 (B) or R17-29 - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - BATTERY)

(a) Disconnect the A12, A13, K20 and K21 power distribution box assembly connectors.

(b) Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:

Click Location & Routing(A13,A12) Click Connector(A13) Click Connector(A12)

Tester Connection

Switch Condition

Specified Condition

A13-1 - Body ground

Ignition switch off

11 to 14 V

A12-1 - Body ground

Ignition switch ON

11 to 14 V

Ignition switch off

Below 1 V

Standard Resistance:

Click Location & Routing(K20,K21) Click Connector(K20) Click Connector(K21)

Tester Connection

Switch Condition

Specified Condition

K20-36 - Body ground

Always

Below 1 Ω

K21-41 - Body ground

Always

Below 1 Ω

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - ECM)

(a) Disconnect the A12 power distribution box assembly connector.

(b) Disconnect the A92 ECM connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(A12,A92) Click Connector(A12) Click Connector(A92)

Tester Connection

Condition

Specified Condition

A12-16 - A92-44 (FREL)

Always

Below 1 Ω

A12-16 or A92-44 (FREL) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. INSPECT POWER DISTRIBUTION BOX ASSEMBLY (FUEL OPN RELAY/FUEL LOCK RELAY)

(a) Remove the power distribution box assembly.

Click here

(b) Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.

Click here

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(A13,R17,K20,K21) Click Connector(A13) Click Connector(R17) Click Connector(K20) Click Connector(K21)

Tester Connection

Condition

Specified Condition

A13-1 - R17-29

Voltage applied between terminals A12-1 and A12-16

Below 1 Ω

A13-1 - R17-29

Voltage not applied between terminals A12-1 and A12-16

10 kΩ or higher

K20-36 - R17-29

Voltage not applied between terminals A12-1 and A12-16

Below 1 Ω

K21-41 - R17-29

K20-36 - R17-29

Voltage applied between terminals A12-1 and A12-16

10 kΩ or higher

K21-41 - R17-29

OK

REPLACE ECM

NG

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

  1. READ VALUE USING GTS (Fuel Lid SW)

(a) Enter the following menus: Powertrain / Engine / Data List.

(b) Read the Data List according to the display on the GTS.

Powertrain > Engine > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Fuel Lid SW

Fuel lid opener switch status

Close or Open

Close: Fuel lid opener switch not pushed

Open: Fuel lid opener switch pushed

-

Powertrain > Engine > Data List

Fuel Lid SW

OK:

The GTS display changes correctly in response to the operation of the fuel lid opener switch.

NG

GO TO STEP 22

OK
  1. INSPECT FUEL LID WITH MOTOR LOCK ASSEMBLY (MOTOR OPERATION)

(a) Remove the fuel lid with motor lock assembly.

Click here

(b) Inspect the fuel lid with motor lock assembly.

Click here

NG

REPLACE FUEL LID WITH MOTOR LOCK ASSEMBLY

OK
  1. CHECK HARNESS AND CONNECTOR (FUEL LID WITH MOTOR LOCK ASSEMBLY - POWER DISTRIBUTION BOX ASSEMBLY AND BODY GROUND)

(a) Disconnect the R37 fuel lid with motor lock assembly connector.

(b) Disconnect the R17 power distribution box assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(R37,R17) Click Connector(R37) Click Connector(R17)

Tester Connection

Condition

Specified Condition

R37-1 (B) - R17-29

Always

Below 1 Ω

R37-2 (E) - Body ground

Always

Below 1 Ω

R37-1 (B) or R17-29 - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - BATTERY)

(a) Disconnect the A12, A13, K20 and K21 power distribution box assembly connectors.

(b) Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:

Click Location & Routing(A13,A12) Click Connector(A13) Click Connector(A12)

Tester Connection

Switch Condition

Specified Condition

A13-1 - Body ground

Ignition switch off

11 to 14 V

A12-1 - Body ground

Ignition switch ON

11 to 14 V

Ignition switch off

Below 1 V

Standard Resistance:

Click Location & Routing(K20,K21) Click Connector(K20) Click Connector(K21)

Tester Connection

Switch Condition

Specified Condition

K20-36 - Body ground

Always

Below 1 Ω

K21-41 - Body ground

Always

Below 1 Ω

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - ECM)

(a) Disconnect the A12 power distribution box assembly connector.

(b) Disconnect the A91 ECM connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(A12,A91) Click Connector(A12) Click Connector(A91)

Tester Connection

Condition

Specified Condition

A12-16 - A91-28 (FREL)

Always

Below 1 Ω

A12-16 or A91-28 (FREL) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. INSPECT POWER DISTRIBUTION BOX ASSEMBLY (FUEL OPN RELAY/FUEL LOCK RELAY)

(a) Remove the power distribution box assembly.

Click here

(b) Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.

Click here

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(A13,R17,K20,K21) Click Connector(A13) Click Connector(R17) Click Connector(K20) Click Connector(K21)

Tester Connection

Condition

Specified Condition

A13-1 - R17-29

Voltage applied between terminals A12-1 and A12-16

Below 1 Ω

A13-1 - R17-29

Voltage not applied between terminals A12-1 and A12-16

10 kΩ or higher

K20-36 - R17-29

Voltage not applied between terminals A12-1 and A12-16

Below 1 Ω

K21-41 - R17-29

K20-36 - R17-29

Voltage applied between terminals A12-1 and A12-16

10 kΩ or higher

K21-41 - R17-29

OK

REPLACE ECM

NG

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

  1. INSPECT FUEL LID OPENER SWITCH

(a) Remove the fuel lid opener switch.

Click here

(b) Inspect the fuel lid opener switch.

Click here

NG

REPLACE FUEL LID OPENER SWITCH

OK
  1. CHECK HARNESS AND CONNECTOR (FUEL LID OPENER SWITCH - ECM AND BODY GROUND)

(a) Disconnect the A91 ECM connector.

(b) Disconnect the K50 fuel lid opener switch connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(K50,A91) Click Connector(K50) Click Connector(A91)

Tester Connection

Condition

Specified Condition

K50-5 (IG) - A91-60 (FUEL)

Always

Below 1 Ω

K50-5 (IG) or A91-60 (FUEL) - Body ground

Always

10 kΩ or higher

K50-2 (E) - Body ground

Always

Below 1 Ω

OK

REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR