Brake Actuator

In this manual: Brake Actuator
How To Troubleshoot Ecu Controlled Systems — 1How To Use This Manual — 1Identification Information — 1Repair Instruction — 1Terms — 12zr-fxe Air Cleaner Filter Element — 12zr-fxe Auxiliary Battery — 12zr-fxe Coolant (for Engine Coolant) — 12zr-fxe Oil And Oil Filter — 12zr-fxe Spark Plug — 1Air Conditioning Filter — 1Battery Cooling Filter — 1Brake Fluid — 1Coolant (for Inverter) — 1Front Brake Flexible Hose — 1Front Disc Brake Pad — 1Front Lower Ball Joint — 1Front Wheel Alignment — 1Front Wiper Rubber — 1General Maintenance — 1M20a-fxs Air Cleaner Filter Element — 1M20a-fxs Auxiliary Battery — 1M20a-fxs Coolant (for Engine Coolant) — 1M20a-fxs Oil And Oil Filter — 1M20a-fxs Spark Plug — 1Pa10/pb10/pb12 Hybrid Transaxle Fluid — 1Q810 Hybrid Transaxle Fluid — 1Rear Brake Flexible Hose — 1Rear Disc Brake Pad — 1Rear Wheel Alignment — 1Steering Column — 1Tire And Wheel — 1Transmitter Battery — 1When Disconnecting Or Reconnecting Battery Terminal — 1When Replacing Or Removing/installing Parts — 1Automatic High Beam Main Switch — 1Automatic High Beam System — 1Driver Monitor Camera — 1Driver Monitor Camera System — 1Driver Monitor Ecu — 1Front Camera — 1Front Camera System — 1Front Radar Sensor System — 1Front Side Radar Sensor — 1Front Side Radar Sensor System — 1Millimeter Wave Radar Sensor — 1Utility — 1Advanced Park — 1Advanced Park Main Switch — 1Amplifier Antenna — 1Audio And Visual System — 1Front Door Speaker — 1Instrument Panel Speaker — 1Microphone — 1Noise Filter — 1Pillar Speaker — 1Radio Antenna Cord (for Back Door) — 1Radio Antenna Cord (for Instrument Panel) — 1Radio Antenna Cord (for Roof) — 1Radio Receiver — 1Rear Door Speaker — 1Roof Antenna — 1Stereo Component Amplifier — 1Stereo Jack Adapter Assembly — 1Window Glass Antenna Wire — 1Back-up Battery — 1Dcm(telematics Transceiver) — 1Manual(sos)switch — 1Safety Connect System — 1Telephone And Gps Antenna (for Front Side) — 1Telephone And Gps Antenna (for Roof Side) — 1Telephone And Gps Antenna Cords — 1Garage Door Opener System (for Digital Inner Mirror) — 1Garage Door Opener System (for Ec Inner Mirror) — 1Blind Spot Monitor Sensor — 1Blind Spot Monitor System — 1Clearance Warning Ecu — 1Intuitive Parking Assist System — 1Panoramic View Monitor Switch — 1Panoramic View Monitor System — 1Parking Assist Ecu — 1Parking Assist Light — 1Parking Assist Monitor System — 1Parking Support Brake System — 1Rear View Monitor System — 1Television Camera (for Front) — 1Television Camera (for Rear) — 1Television Camera (for Side) — 1Ultrasonic Sensor (for Front) — 1Ultrasonic Sensor (for Rear) — 1Brake Actuator — 1Brake Pedal Stroke Sensor — 1Electronically Controlled Brake System — 1Front Speed Sensor — 1Rear Speed Sensor (for Awd) — 1Steering Angle Sensor — 1Brake Booster — 1Brake Fluid — 1Brake Line — 1Brake Pedal — 1Brake System — 1Electric Parking Brake Actuator — 1Electric Parking Brake Switch — 1Electric Parking Brake System — 1Forced Release — 1Front Axle Hub — 1Front Axle Hub Bolt — 1Rear Axle Carrier (for 2wd) — 1Rear Axle Carrier (for Awd) — 1Rear Axle Hub (for 2wd) — 1Rear Axle Hub (for Awd) — 1Rear Axle Hub Bolt — 1Steering Knuckle — 1Drive Shaft System — 1Front Drive Shaft Assembly — 1Rear Drive Shaft Assembly — 1Combination Switch — 1Electronic Shift Lever System — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Oil Seal — 1Hybrid Transaxle System — 1Input Shaft Oil Seal — 1Motor Cable — 1Pa10 Hybrid Vehicle Transaxle — 1Pa10 Manual Parking Lock Release — 1Pa10 Oil Cooler — 1Pb10/pb12 Hybrid Vehicle Transaxle — 1Pb10/pb12 Manual Parking Lock Release — 1Pb10/pb12 Oil Cooler — 1Shift Control Actuator — 1Shift Lever — 1Shift Lever Knob — 1Differential Side Gear Shaft — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Side Gear Oil Seal — 1Motor Cable — 1Rear Traction Motor — 1Coolant (for Engine) — 1Cooling Fan Motor — 1Cooling Fan System — 1Radiator — 1Relay — 1Thermostat — 1Water Pump — 1Canister — 1Egr Cooler — 1Egr Valve — 1Emission Control System — 1Fuel Tank Cap — 1Pcv Valve — 1Purge Valve — 1Vacuum Sensor — 1Air Fuel Ratio Sensor — 1Camshaft Oil Control Valve — 1Camshaft Position Sensor — 1Crankshaft Position Sensor — 1Ecm — 1Engine Coolant Temperature Sensor — 1Heated Oxygen Sensor — 1Ignition Coil And Spark Plug — 1Ignition System — 1Knock Sensor — 1Mass Air Flow Meter — 1Relay — 1Sfi System — 1Throttle Body — 1Camshaft — 1Cylinder Block — 1Cylinder Head — 1Cylinder Head Gasket — 1Engine — 1Engine Assembly — 1Engine Unit — 1Front Crankshaft Oil Seal — 1Rear Crankshaft Oil Seal — 1Fuel Filter — 1Fuel Injector — 1Fuel Pressure Regulator — 1Fuel Pump — 1Fuel Sender Gauge Assembly — 1Fuel System — 1Fuel Tank — 1Air Cleaner Filter Element — 1Exhaust Manifold — 1Exhaust Pipe — 1Intake Manifold — 1Intake System — 1Lubrication System — 1Oil And Oil Filter — 1Oil Pan And Oil Level Sensor — 1Oil Pressure Switch — 1Oil Pump — 1Accelerator Pedal Sensor — 1Battery Blower (for Hev Model) — 1Battery Ecu (for Hev Model) — 1Battery Ecu (for Phev Model) — 1Battery Voltage Sensor (for Phev Model) — 1Charge Cable (for Phev Model) — 1Charge Indicator (for Phev Model) — 1Charge Inlet (for Phev Model) — 1Combination Switch — 1Coolant (for Inverter) — 1Cooler (for Phev Model) — 1Electric Vehicle Charger Assembly (for Phev Model) — 1Frame Wire (for Hev Model) — 1Frame Wire (for Phev Model) — 1Heater Relay (for Phev Model) — 1Hv Battery (for Hev Model) — 1Hv Battery (for Phev Model) — 1Hv Battery Heater (for Phev Model) — 1Hv Battery Stack (for Phev Model) — 1Hv Relay Assembly (for Hev Model) — 1Hv Relay Assembly (for Phev Model) — 1Hybrid Battery System (for 2zr-fxe) — 1Hybrid Battery System (for M20a-fxs) — 1Hybrid Battery System (for Phev Model) — 1Hybrid Vehicle Control Ecu — 1Inverter With Converter (for Hev Model) — 1Motor Generator Control System (for 2zr-fxe) — 1Plug-in Charge Control System (for Phev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Service Plug Grip (for Hev Model) — 1Sub Radiator — 1Water Pump With Motor — 1Auxiliary Battery — 1Battery Current Sensor — 1Charging System — 1Solar Charging System — 1Solar Control Unit — 1Solar Roof — 1Can Communication System (for Hev Model) — 1Lin Communication System — 1Network Gateway Ecu — 1Integration Control Supply — 1Main Body Ecu — 1Power Integration System — 1Sub Battery System — 1Power Steering Ecu — 1Power Steering System — 1Heated Steering Wheel Controller — 1Heated Steering Wheel System — 1Steering Column Assembly — 1Steering Heater Switch — 1Steering Pad Switch — 1Steering System — 1Steering Wheel — 1Front Lower Ball Joint — 1Front Lower Suspension Arm (for 2zr-fxe Lh Side) — 1Front Lower Suspension Arm (for 2zr-fxe Rh Side) — 1Front Lower Suspension Arm (for M20a-fxs) — 1Front Shock Absorber — 1Front Stabilizer Bar — 1Front Suspension Member — 1Rear Coil Spring — 1Rear Lower Arm (for Awd Lh Side) — 1Rear Lower Arm (for Awd Rh Side) — 1Rear Lower Arm (for Hev Model 2wd) — 1Rear Lower Arm (for Phev Model) — 1Rear Shock Absorber — 1Rear Stabilizer Bar — 1Rear Suspension Member (for 2wd) — 1Rear Suspension Member (for Awd) — 1Rear Trailing Arm — 1Rear Upper Arm — 1Tire And Wheel System — 1Tire Repair Seal — 1Tire Pressure Warning Receiver — 1Tire Pressure Warning System — 1Tire Pressure Warning Valve — 1Acoustic Vehicle Alerting System — 1Vehicle Approaching Speaker — 1Vehicle Approaching Speaker Ecu — 1Back Door — 1Back Door Closer Ecu — 1Back Door Opener Switch — 1Back Door Support — 1Back Door Weatherstrip — 1Charge Lid Courtesy Switch — 1Charge Lid Opener Motor Assembly — 1Charge Lid Opener System — 1Charge Lid Opener Unit — 1Front Door — 1Front Door Opening Trim Weatherstrip — 1Fuel Lid Opener Motor Assembly — 1Fuel Lid Opener Switch — 1Fuel Lid Opener System — 1Hood — 1Hood Lock Control Cable Assembly — 1Power Back Door Closer Switch — 1Power Back Door Control Switch — 1Power Back Door Drive Unit — 1Power Back Door System — 1Power Back Door Touch Sensor — 1Power Back Door Warning Buzzer — 1Rear Door — 1Rear Door Opening Trim Weatherstrip — 1Reserve Lock Switch — 1Front Bumper — 1Front Door Belt Moulding — 1Front Door Window Frame Moulding — 1Front Fender — 1Front Pillar Upper Cover — 1Grille Shutter — 1Grille Shutter System — 1Name Plate — 1Quarter Garnish — 1Rear Bumper — 1Rear Door Belt Moulding — 1Rear Door Window Frame Moulding — 1Rear Wheel House Plate — 1Rocker Panel Moulding — 1Roof Drip Side Finish Moulding — 1Roof Garnish — 1Wheel Opening Moulding (for Front Side) — 1Wheel Opening Moulding (for Rear Side) — 1Windshield Outside Moulding — 1Horn — 1Horn System — 1Relay — 1Automatic Light Control Sensor — 1Back-up Light Assembly — 1Charge Lid Light — 1Front Marker Light — 1Hazard Warning Switch — 1Headlight Assembly — 1Headlight Dimmer Switch — 1Headlight Leveling Switch — 1High Mounted Stop Light Assembly — 1Illumination Light Assembly — 1License Plate Light Assembly — 1Lighting System — 1Rear Combination Light Assembly — 1Rear Light Assembly — 1Rear Side Marker Light Assembly — 1Relay — 1Side Turn Signal Light Assembly — 1Stop Light Switch — 1Switch Housing — 1Outer Mirror Switch — 1Outer Rear View Mirror — 1Outer Rear View Mirror Cover — 1Outer Rear View Mirror Glass — 1Power Mirror Control System — 1Back Door Glass — 1Front Passenger Side Power Window Switch — 1Power Window Control System — 1Power Window Master Switch — 1Power Window Regulator Motor (for Front Door) — 1Power Window Regulator Motor (for Rear Door) — 1Rear Power Window Switch — 1Relay — 1Roof Window Fix Glass — 1Window Defogger System — 1Windshield Deicer Switch — 1Windshield Deicer System — 1Windshield Glass — 1Front Wiper Motor — 1Rain Sensor — 1Relay — 1Washer Motor — 1Washer Nozzle (for Front Side) — 1Washer Nozzle (for Rear Television Camera) — 1Wiper And Washer System — 1Wiper Ecu — 1Wiper Switch — 1Back Door Lock — 1Door Control Receiver — 1Door Control Switch — 1Door Control Transmitter — 1Door Lock Release Motor (for Rear Side) — 1Door Outside Handle (for Rear Side) — 1Front Door Lock — 1Power Door Lock Control System — 1Rear Door Lock — 1Transmitter Battery — 1Wireless Door Lock Control System — 1Accumulator — 1Air Conditioning Amplifier — 1Air Conditioning Panel — 1Air Conditioning Pressure Sensor — 1Air Conditioning Unit — 1Ambient Temperature Sensor — 1Blower Unit — 1Condenser (for Hev Model) — 1Condenser (for Phev Model) — 1Discharge Temperature Sensor — 1Electric Expansion Valve (cooling) — 1Electric Expansion Valve (heating) — 1Evaporator Pipe Temperature Sensor — 1Evaporator Pressure Regulator — 1Front Blower Motor — 1Front Evaporator Front Solenoid Valve — 1Air Conditioning System (for Hev Model) — 1Front Evaporator Temperature Sensor — 1Heat Exchanger Temperature Sensor — 1Heat Pump Ecu — 1High Pressure Magnetic Valve — 1Humidity Sensor — 1Internal Condenser Temperature Sensor — 1Low Pressure Magnetic Valve — 1Refrigerant (for Hfc-134a(r134a)) — 1Refrigerant Line (for Hev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Room Temperature Sensor — 1Solar Sensor — 1Floor Carpet — 1Front Console Box — 1Instrument Panel Safety Pad — 1Roof Headlining — 1Roof Sunshade — 1Ambient Light (for Driver Side) — 1Ambient Light (for Front Passenger Side) — 1Back Door Courtesy Switch — 1Footwell Light — 1Glove Box Light — 1Lighting System — 1Luggage Compartment Room Light — 1Personal Light — 1Room Light — 1Vanity Light — 1Vanity Light Switch — 1Combination Meter — 1Meter / Gauge System — 1Trip Switch — 1Digital Inner Mirror — 1Digital Rear-view Mirror System — 1Inner Mirror Monitor Camera — 1Inner Rear View Mirror (w/o Ec Mirror) — 1Accessory Power Outlet System — 1Power Outlet Socket (for Console Box Front Side) — 1Power Outlet Socket (for Console Box Rear Side) — 1Power Outlet Socket (for Console Box) — 1Power Outlet Socket (for Luggage Compartment) — 1Power Outlet Switch — 1Wireless Charger Assembly — 1Wireless Charging System — 1Climate Control Seat System — 1Front Power Seat Control System (w/ Memory) — 1Front Power Seat Motor Assembly — 1Front Seat Assembly (for Power Seat) — 1Front Seat Cushion Heater (for Power Seat) — 1Front Seatback Heater (for Power Seat) — 1Lumbar Support Adjuster Assembly — 1Power Seat Control Ecu — 1Power Seat Switch — 1Power Seat Track Rail Assembly — 1Rear Seat Assembly — 1Rear Seat Cushion Heater — 1Rear Seat Reminder System — 1Rear Seatback Heater — 1Seat Heater Control — 1Seat Heater Switch (for Front Seat) — 1Seat Heater Switch (for Rear Side) — 1Seat Heater System — 1Seat Memory Switch — 1Child Restraint Seat Anchor Bracket — 1Front Seat Inner Belt Assembly — 1Front Seat Outer Belt Assembly — 1Occupant Detection Sensor (for Front Passenger Side) — 1Rear Center Seat Outer Belt Assembly — 1Rear Seat Inner Belt Assembly (for Rh Side) — 1Rear Seat Outer Belt Assembly — 1Seat Belt Warning System (w/ Occupant Classification System) — 1Tongue Plate Stopper — 1Airbag System — 1Center Airbag Sensor Assembly — 1Curtain Shield Airbag Assembly — 1Front Airbag Sensor — 1Front Passenger Airbag Assembly — 1Front Seat Side Airbag Assembly — 1Inspection After Collision — 1Knee Airbag Assembly — 1Occupant Classification System — 1Rear Seat Side Airbag Assembly — 1Side Airbag Sensor (for Center Pillar) — 1Side Airbag Sensor (for Front Door) — 1Spiral Cable — 1Steering Pad — 1Certification Ecu — 1Digital Key Ecu — 1Digital Key Receiver (for Front Floor) — 1Digital Key Receiver (for Outside Luggage Compartment) — 1Digital Key Receiver (for Rear Door) — 1Digital Key System — 1Electrical Key Oscillator (for Front Floor) — 1Electrical Key Oscillator (for Outside Luggage Compartment) — 1Electrical Key Oscillator (for Rear Floor) — 1Engine Hood Courtesy Switch — 1Id Code Box — 1Smart Key System (for Start Function) — 1
~26min read
010203040506.55N·mlb·ft
Tightening torque found on this page
  • Removal
  • Installation
  • Reset Memory / Calibration

Removal

REMOVAL

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during brake actuator assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

*1: Also necessary after performing a tire rotation.

*2: It is not necessary to perform this procedure if the tire pressure warning valve and transmitters are installed to the same location.

No. 2 skid control ECU (brake actuator assembly)

Update ECU security key

Toyota Prius Vehicle Control History (RoB) are stored

  • Bleed air
  • Perform "Calibration"
  • DTCs are stored
  • ABS warning light illuminates
  • Brake system warning light (yellow indicator) illuminates
  • Slip indicator light illuminates
  • Electronically controlled brake system disabled or malfunctions

Bleeding:

Calibration:

Operate the electric parking brake switch

Electric Parking Brake System

Tires

  • Initialization*1*2
  • Tire Position Identification*1*2

Tire Pressure Warning System

Refer to Procedures Necessary When Replacing Parts (for Tire Pressure Warning System)

Rear television camera assembly optical axis (Back camera position setting)

Parking Assist Monitor System

Parking assist ECU initialization

Panoramic View Monitor System

Advanced Park

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

Learning completes when Toyota Prius vehicle is driven

Effect/Inoperative Function when Necessary Procedure not Performed

Necessary Procedure

Link

Front Camera System

  • Back door opener

Drive the Toyota Prius vehicle straight ahead at 35 km/h or more for 5 seconds or more.

Learning completes when vehicle is operated normally

Effect/Inoperative Function when Necessary Procedure not Performed

Necessary Procedure

Link

*1: w/o Power Back Door System

*2: w/ Power Back Door System

Power Door Lock Control System*1

Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.

Power Back Door System*2

Reset back door close position

Air Conditioning System

for HEV Model:
  • After the ignition switch is turned to ON, the servo motor standard position is recognized.
for PHEV Model:
  • After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized.

-

NOTICE:

  • After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 3 minutes before disconnecting the cable from the negative(-) auxiliary battery terminal.
  • When the cable is disconnected from the negative (-) auxiliary battery terminal and the security lock setting has been enabled, multi-display operations will be disabled upon next startup unless the password is entered. Be sure to check the security lock setting before disconnecting the cable from the negative (-) auxiliary battery terminal.
COMPONENTS (REMOVAL)

Procedure

Part Name Code

1

PRECAUTION

-

-

-

2

RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

-

-

-

3

DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

-

-

-

-

4

WINDSHIELD WIPER MOTOR AND LINK

-

-

-

-

5

WATER GUARD PLATE

55734D

-

-

-

6

OUTER COWL TOP PANEL SUB-ASSEMBLY

55701J

-

-

-

7

DRAIN BRAKE FLUID

-

-

-

8

NO. 1 ENGINE UNDER COVER ASSEMBLY

51410

-

-

-

*A

for 2ZR-FXE

*B

for M20A-FXS

Procedure

Part Name Code

9

DASH PANEL HEAT INSULATOR

55225C

-

-

-

10

NO. 5 DASH PANEL INSULATOR PLATE

55228

-

-

-

*A

for M20A-FXS except PHEV Model

-

-

Procedure

Part Name Code

11

DASH PANEL HEAT INSULATOR

55225C

-

-

-

12

NO. 5 DASH PANEL INSULATOR PLATE

55228

-

-

-

*A

for PHEV Model

-

-

Procedure

Part Name Code

13

SUCTION PIPE SUB-ASSEMBLY

88707

-

-

*A

except PHEV Model

-

-

*1

O-RING

*2

AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY

●

Non-reusable part

-

-

Procedure

Part Name Code

14

NO. 1 SUCTION TUBE

88717U

-

-

*A

for PHEV Model

-

-

*1

O-RING

*2

PIPING CLAMP

*3

NO. 7 DISCHARGE TUBE

*4

NO. 1 DISCHARGE TUBE

*5

LIQUID TUBE SUB-ASSEMBLY B

*6

COOLER EXPANSION VALVE

*7

DISCHARGE TUBE SUB-ASSEMBLY

-

-

●

Non-reusable part

-

-

Procedure

Part Name Code

15

ENGINE ROOM MAIN WIRE

82111

-

-

16

DISCONNECT BRAKE LINE

-

-

-

17

BRAKE ACTUATOR WITH BRACKET

-

-

-

Procedure

Part Name Code

18

BRAKE ACTUATOR ASSEMBLY

44510

-

-

19

NO. 1 BRAKE ACTUATOR CASE COLLAR

44521A

-

-

-

20

BRAKE ACTUATOR BOLT CUSHION

44546A

-

-

-

*1

BRAKE ACTUATOR BRACKET ASSEMBLY

-

-

PROCEDURE

1. PRECAUTION

NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click here

2. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

for HFC-134a(R134a): Click here

for HFO-1234yf(R1234yf): Click here

3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

for M20A-FXS: Click here

for 2ZR-FXE: Click here

4. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Click here

5. REMOVE WATER GUARD PLATE

Click here

6. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

Click here

7. DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.

8. REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

for M20A-FXS: Click here

for 2ZR-FXE: Click here

9. REMOVE DASH PANEL HEAT INSULATOR (for M20A-FXS except PHEV Model)

10. REMOVE NO. 5 DASH PANEL INSULATOR PLATE (for M20A-FXS except PHEV Model)

11. REMOVE DASH PANEL HEAT INSULATOR (for PHEV Model)

12. REMOVE NO. 5 DASH PANEL INSULATOR PLATE (for PHEV Model)

13. SEPARATE SUCTION PIPE SUB-ASSEMBLY (except PHEV Model)

Move in this Direction

Rotate in this Direction

(1) Remove the bolt and clamp.

(2) Separate the air conditioning tube and accessory assembly.

(3) Remove the O-ring from the air conditioning tube and accessory assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.

(4) Remove the clamp.

(5) Remove the bolt and rotate the hook connector as shown in the illustration.

(6) Disconnect the suction pipe sub-assembly from the air conditioning unit assembly.

(7) Remove the 2 O-rings from the suction pipe sub-assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.

(8) Move aside the suction pipe sub-assembly as shown in the illustration.

14. SEPARATE NO. 1 SUCTION TUBE (for PHEV Model)

Rotate in this Direction

-

-

(1) Remove the bolt and 3 clamps.

(2) Disconnect the connector and separate the connector from cooler expansion valve.

(3) Remove the bolt and rotate the hook connector as shown in the illustration.

(4) Disconnect the No. 1 suction tube from the air conditioning unit assembly.

(1) Remove the 2 O-rings from the No. 1 suction tube.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.

(1) Disconnect the connector and remove the bolt.

(2) Disconnect the No. 7 discharge tube from the air conditioning unit assembly.

(3) Remove the 2 O-rings from the discharge tube.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.

(1) Remove the piping clamp from No. 1 discharge tube and liquid tube sub-assembly B.

(2) Remove the 2 nuts and disconnect the No. 1 discharge tube and liquid tube sub-assembly B.

(3) Remove the 2 O-rings from the No. 1 discharge tube and liquid tube sub-assembly B.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.

Rotate in this Direction

-

-

(1) Remove the bolt and rotate the hook connector as shown in the illustration.

(2) Remove the 2 O-rings from the No. 8 discharge tube.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.

Move in this Direction

-

-

(1) Move aside the air conditioning tube and accessory assembly as shown in the illustration.

15. DISCONNECT ENGINE ROOM MAIN WIRE

Release the lock lever

Disconnect the connector

(1) Disengage the clamp to separate the engine room main wire from the brake actuator bracket assembly.

(2) Release the lock lever and disconnect the connector from the brake actuator assembly.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.

16. DISCONNECT BRAKE LINE

NOTICE:

  • Do not kink or damage the brake lines.
  • Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.

*a

From 1st Chamber of Brake Master Cylinder Assembly

*b

From 2nd Chamber of Brake Master Cylinder Assembly

*c

To Front Disc Brake Cylinder Assembly RH

*d

To Front Disc Brake Cylinder Assembly LH

*e

To Rear Disc Brake Cylinder Assembly RH

*f

To Rear Disc Brake Cylinder Assembly LH

(1) Use tags or make a memo to identify the places to reconnect the brake lines.

(2) Using a union nut wrench, disconnect the 6 brake lines from the brake actuator assembly.

17. REMOVE BRAKE ACTUATOR WITH BRACKET

NOTICE:

  • Do not kink or damage the brake lines.
  • Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.
  • Be careful not to allow any brake fluid to enter the connector.
  • Do not hold the brake actuator with bracket by the connector.
  • Do not drop the brake actuator with bracket when carrying it.

HINT:

Remove the brake actuator with bracket while avoiding the brake lines.

18. REMOVE BRAKE ACTUATOR ASSEMBLY

NOTICE:

  • Do not hold the brake actuator assembly by the connector.
  • Do not drop the brake actuator assembly when carrying it.

19. REMOVE NO. 1 BRAKE ACTUATOR CASE COLLAR

20. REMOVE BRAKE ACTUATOR BOLT CUSHION

Installation

INSTALLATION

NOTICE:

  • After replacing the brake actuator assembly, make sure to perform update ECU security key.
  • After performing the update ECU security key procedure, make sure to perform the initialization procedure for when the cable has been disconnected and reconnected to the negative (-) auxiliary battery terminal.
COMPONENTS (INSTALLATION)

Procedure

Part Name Code

1

BRAKE ACTUATOR BOLT CUSHION

44546A

-

-

-

2

NO. 1 BRAKE ACTUATOR CASE COLLAR

44521A

-

-

3

BRAKE ACTUATOR ASSEMBLY

44510

-

-

*1

BRAKE ACTUATOR BRACKET ASSEMBLY

-

-

Tightening torque for "Major areas involving basic Toyota Prius vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf)

-

-

Procedure

Part Name Code

4

BRAKE ACTUATOR WITH BRACKET

-

-

-

5

BRAKE LINE

-

-

-

6

ENGINE ROOM MAIN WIRE

82111

-

-

Tightening torque for "Major areas involving basic Toyota Prius vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf)

*

For use with a union nut wrench

Procedure

Part Name Code

7

SUCTION PIPE SUB-ASSEMBLY

88707

-

-

*A

except PHEV Model

-

-

*1

O-RING

*2

AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY

N*m (kgf*cm, ft.*lbf): Specified torque

●

Non-reusable part

Compressor oil ND-OIL 11 or equivalent

-

-

Procedure

Part Name Code

8

NO. 1 SUCTION TUBE

88717U

-

-

*A

for PHEV Model

-

-

*1

O-RING

*2

PIPING CLAMP

*3

NO. 7 DISCHARGE TUBE

*4

NO. 1 DISCHARGE TUBE

*5

LIQUID TUBE SUB-ASSEMBLY B

*6

COOLER EXPANSION VALVE

*7

DISCHARGE TUBE SUB-ASSEMBLY

*8

NO. 8 DISCHARGE TUBE

N*m (kgf*cm, ft.*lbf): Specified torque

●

Non-reusable part

Compressor oil ND-OIL 11 or equivalent

-

-

Procedure

Part Name Code

9

NO. 5 DASH PANEL INSULATOR PLATE

55228

-

-

-

10

DASH PANEL HEAT INSULATOR

55225C

-

-

-

*A

for M20A-FXS except PHEV Model

-

-

N*m (kgf*cm, ft.*lbf): Specified torque

-

-

Procedure

Part Name Code

11

NO. 5 DASH PANEL INSULATOR PLATE

55228

-

-

-

12

DASH PANEL HEAT INSULATOR

55225C

-

-

-

*A

for PHEV Model

-

-

N*m (kgf*cm, ft.*lbf): Specified torque

-

-

Procedure

Part Name Code

13

CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

-

-

-

14

UPDATE ECU SECURITY KEY

-

-

-

15

BLEED BRAKE SYSTEM

-

-

-

16

OUTER COWL TOP PANEL SUB-ASSEMBLY

55701J

-

-

-

17

WATER GUARD PLATE

55734D

-

-

-

18

WINDSHIELD WIPER MOTOR AND LINK

-

-

-

-

19

NO. 1 ENGINE UNDER COVER ASSEMBLY

51410

-

-

-

20

BRAKE SYSTEM CALIBRATION

-

-

-

21

AIR CONDITIONING SYSTEM WITH REFRIGERANT

-

-

-

22

WARM UP COMPRESSOR

-

-

-

23

INSPECT FOR REFRIGERANT LEAK

-

-

-

24

PERFORM INITIALIZATION

-

-

-

25

INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

-

-

-

26

CHECK AND CLEAR DTC

-

-

-

*A

for 2ZR-FXE

*B

for M20A-FXS

Tightening torque for "Major areas involving basic Toyota Prius vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf)

N*m (kgf*cm, ft.*lbf): Specified torque

PROCEDURE

1. INSTALL BRAKE ACTUATOR BOLT CUSHION

2. INSTALL NO. 1 BRAKE ACTUATOR CASE COLLAR

NOTICE:

Make sure that the No. 1 brake actuator case collar is in full contact with the brake actuator bolt cushion.

3. INSTALL BRAKE ACTUATOR ASSEMBLY

(1) While contacting the 3 connecting portions of the brake actuator assembly and the brake actuator bracket assembly, install the brake actuator assembly to the brake actuator bracket assembly with the 3 bolts.

Torque:

6,5 N·m {66 kgf·cm, 58 in·lbf}

NOTICE:

  • Do not remove the hole plugs of a new brake actuator assembly before connecting the brake lines because the brake actuator assembly is filled with brake fluid.
  • Do not hold the brake actuator assembly by the connector.
  • Do not drop the brake actuator assembly when carrying it.

4. INSTALL BRAKE ACTUATOR WITH BRACKET

NOTICE:

  • Do not kink or damage the brake lines.
  • Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.
  • Be careful not to allow any brake fluid to enter the connector.
  • Do not hold the brake actuator with bracket by the connector.
  • Do not drop the brake actuator with bracket when carrying it.

(1) Temporarily install the brake actuator with bracket to the Toyota Prius vehicle body with the 2 nuts.

NOTICE:

  • Do not kink or damage the brake lines.
  • Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.
  • Be careful not to allow any brake fluid to enter the connector.
  • Do not hold the brake actuator assembly by the connector.
  • Do not drop the brake actuator with bracket when carrying it.

HINT:

Install the brake actuator with bracket while avoiding the brake lines.

(2) Fully tighten the 2 nuts in the order shown in the illustration.

Torque:

19 N·m {194 kgf·cm, 14 ft·lbf}

5. CONNECT BRAKE LINE

*a

From 1st Chamber of Brake Master Cylinder Assembly

*b

From 2nd Chamber of Brake Master Cylinder Assembly

*c

To Front Disc Brake Cylinder Assembly RH

*d

To Front Disc Brake Cylinder Assembly LH

*e

To Rear Disc Brake Cylinder Assembly RH

*f

To Rear Disc Brake Cylinder Assembly LH

*g

Torque Wrench Fulcrum Length

-

-

(1) Temporarily tighten the 6 brake lines to the correct position on the brake actuator assembly as shown in the illustration.

NOTICE:

  • Do not kink or damage the brake lines.
  • Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.

(2) Using a union nut wrench, fully tighten the 6 brake lines.

Torque:

Specified tightening torque (A) :

19,5 N·m {199 kgf·cm, 14 ft·lbf}

Specified tightening torque (B) :

15,2 N·m {155 kgf·cm, 11 ft·lbf}

NOTICE:

Do not kink or damage the brake lines.

HINT:

  • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

    Click here

  • for Specified Tightening Torque (A):

    When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) torque wrench (fulcrum length of 162 mm (6.38 in.)):

    17.4 N*m (177 kgf*cm, 13 ft.*lbf)

  • for Specified Tightening Torque (B):

    When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) torque wrench (fulcrum length of 162 mm (6.38 in.)):

    13.4 N*m (137 kgf*cm, 10 ft.*lbf)

6. CONNECT ENGINE ROOM MAIN WIRE

NOTICE:

  • Make sure that the connector is locked securely.
  • Make sure that the connector can be connected smoothly.
  • Do not allow water, oil or dirt to enter the connector.

7. CONNECT SUCTION PIPE SUB-ASSEMBLY (except PHEV Model)

Compressor oil ND-OIL 11 or equivalent

Install in this Direction

Rotate in this Direction

-

-

(1) Remove the vinyl tape from the suction pipe sub-assembly, sufficiently apply compressor oil to 2 new O-rings and the fitting surface of the suction pipe sub-assembly.

Compressor Oil:

ND-OIL 11 or equivalent

(2) Install the 2 O-rings to the suction pipe sub-assembly.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.

(3) Connect the suction pipe sub-assembly and rotate the hook connector as shown in the illustration.

(4) Insert the tube joint into the fitting hole securely and install the bolt.

Torque:

9,8 N·m {100 kgf·cm, 87 in·lbf}

(5) Engage the clamp.

(6) Remove the vinyl tape from the air conditioning tube and accessory assembly, sufficiently apply compressor oil to a new O-ring and the fitting surface of the air conditioning tube and accessory assembly.

Compressor Oil:

ND-OIL 11 or equivalent

(7) Install the O-ring to the air conditioning tube and accessory assembly.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.

(8) Connect the air conditioning tube and accessory assembly with the clamp and bolt.

Torque:

9,8 N·m {100 kgf·cm, 87 in·lbf}

8. CONNECT NO. 1 SUCTION TUBE (for PHEV Model)

Compressor oil ND-OIL 11 or equivalent

Install in this Direction

Rotate in this Direction

-

-

(1) Remove the vinyl tape from the discharge tube sub-assembly, sufficiently apply compressor oil to 2 new O-rings and the fitting surface of the discharge tube sub-assembly.

Compressor Oil:

ND-OIL 11 or equivalent

(2) Install the 2 O-rings to the discharge tube sub-assembly.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.

(3) Connect the discharge tube sub-assembly and rotate the hook connector as shown in the illustration.

Torque:

5,4 N·m {55 kgf·cm, 48 in·lbf}

Compressor oil ND-OIL 11 or equivalent

Install in this Direction

(1) Remove the vinyl tape from the No. 1 discharge tube and liquid tube sub-assembly B, sufficiently apply compressor oil to 2 new O-rings and the fitting surface of the No. 1 discharge tube and liquid tube sub-assembly B.

Compressor Oil:

ND-OIL 11 or equivalent

(2) Install the 2 O-rings to the No. 1 discharge tube and liquid tube sub-assembly B.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.

(3) Install the 2 nuts to connect the No. 1 discharge tube and liquid tube sub-assembly B.

Torque:

9,8 N·m {100 kgf·cm, 87 in·lbf}

(4) Install the piping clamp to the No. 1 discharge tube and liquid tube sub-assembly B.

Compressor oil ND-OIL 11 or equivalent

Install in this Direction

(1) Remove the vinyl tape from the No. 8 discharge tube, sufficiently apply compressor oil to a new O-ring and the fitting surface of the No. 8 discharge tube.

Compressor Oil:

ND-OIL 11 or equivalent

(2) Install the O-ring to the No. 8 discharge tube.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.

(3) Remove the vinyl tape from the No. 7 discharge tube, sufficiently apply compressor oil to a new O-ring and the fitting surface of the No. 7 discharge tube.

Compressor Oil:

ND-OIL 11 or equivalent

(4) Install the O-ring to the No. 7 discharge tube.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.

(5) Connect the connector and install the No. 7 discharge tube with the bolt.

Torque:

9,8 N·m {100 kgf·cm, 87 in·lbf}

Compressor oil ND-OIL 11 or equivalent

Install in this Direction

(1) Remove the vinyl tape from the No. 1 suction tube, sufficiently apply compressor oil to 2 new O-rings and the fitting surface of the No. 1 suction tube.

Compressor Oil:

ND-OIL 11 or equivalent

(2) Install the 2 O-rings to the No. 1 suction tube.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.

Rotate in this Direction

-

-

(1) Connect the No. 1 suction tube and rotate the hook connector as shown in the illustration.

(2) Insert the tube joint into the fitting hole securely and install the bolt.

Torque:

5,4 N·m {55 kgf·cm, 48 in·lbf}

(3) Install the connector to the No. 1 suction tube and connect the connector.

(4) Connect the No. 1 suction tube with the 3 clamps and bolt.

Torque:

9,8 N·m {100 kgf·cm, 87 in·lbf}

9. INSTALL NO. 5 DASH PANEL INSULATOR PLATE (for M20A-FXS except PHEV Model)

Torque:

5 N·m {51 kgf·cm, 44 in·lbf}

10. INSTALL DASH PANEL HEAT INSULATOR (for M20A-FXS except PHEV Model)

Torque:

5 N·m {51 kgf·cm, 44 in·lbf}

11. INSTALL NO. 5 DASH PANEL INSULATOR PLATE (for PHEV Model)

Torque:

5 N·m {51 kgf·cm, 44 in·lbf}

12. INSTALL DASH PANEL HEAT INSULATOR (for PHEV Model)

Torque:

5 N·m {51 kgf·cm, 44 in·lbf}

13. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

for M20A-FXS: Click here

for 2ZR-FXE: Click here

14. UPDATE ECU SECURITY KEY

HINT:

Perform this procedure only when replacement of the brake actuator assembly is necessary.

Click here

15. BLEED BRAKE SYSTEM

Click here

16. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY

Click here

17. INSTALL WATER GUARD PLATE

Click here

18. INSTALL WINDSHIELD WIPER MOTOR AND LINK

Click here

19. INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY

for M20A-FXS: Click here

for 2ZR-FXE: Click here

20. PERFORM BRAKE SYSTEM CALIBRATION

HINT:

Perform this procedure only when replacement of the brake actuator assembly is necessary.

Click here

21. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

for HFC-134a(R134a): Click here

for HFO-1234yf(R1234yf): Click here

22. WARM UP COMPRESSOR

for HFC-134a(R134a): Click here

for HFO-1234yf(R1234yf): Click here

23. INSPECT FOR REFRIGERANT LEAK

for HFC-134a(R134a): Click here

for HFO-1234yf(R1234yf): Click here

24. PERFORM INITIALIZATION

HINT:

The parking brake indicator light blinks (red) when the ignition switch is turned to ON after replacing the brake actuator assembly. Operate the electric parking brake switch assembly to turn off the parking brake indicator light.

Click here

25. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system are used.

Click here

26. CHECK AND CLEAR DTC

Click here

Reset Memory / Calibration

RESET MEMORY / CALIBRATION

NOTICE:

  • When replacing the brake pedal stroke sensor assembly, brake pedal, No. 1 skid control ECU (brake booster with master cylinder assembly), No. 2 skid control ECU (brake actuator assembly) or yaw rate and acceleration sensor (airbag sensor assembly), perform "Calibration".
  • When "Bleeding" is performed after replacing the No. 1 skid control ECU (brake booster with master cylinder assembly) or No. 2 skid control ECU (brake actuator assembly), "Calibration" will be performed automatically.
  • When reinstalling the yaw rate and acceleration sensor (airbag sensor assembly), perform "Calibration".
  • Make sure to perform the yaw rate and acceleration sensor zero point calibration on a flat surface (gradient of 0.2° or less) and ensure that the doors are not opened or closed and the Toyota Prius vehicle is not moved or shaken. Also, to avoid vibration due to engine idle, do not turn the ignition switch to ON (READY).
  • When performing the yaw rate and acceleration sensor zero point calibration, make sure that tire pressure is as specified and the vehicle is in full contact with the ground (not completely or partially lifted up).

PROCEDURE

1. CONFIRMATION BEFORE CALIBRATION

(a) To ensure that calibration completes correctly, confirm the following items before performing "Calibration":

(1) The auxiliary battery voltage is 11 to 15.5 V when the ignition switch is turned to ON (READY).

(2) The brake booster with master cylinder assembly and brake actuator assembly are not hot.

HINT:

If the temperature of the brake booster with master cylinder assembly or brake actuator assembly is excessively high, wait until it cools down before performing "Calibration".

2. RESET MEMORY

(a) Turn the ignition switch off.

(b) Check that the steering wheel is centered.

(c) Check that park (P) is selected.

(d) Connect the GTS to the DLC3.

(e) Turn the ignition switch to ON.

(f) Turn the GTS on.

(g) Using the GTS, perform "Reset Memory". Enter the following menus: Chassis / Brake/EPB / Utility / Reset Memory.

Chassis > Brake/EPB > Utility

Reset Memory

NOTICE:

When performing "Reset Memory", each warning light or indicator light illuminates or flashes, and a DTC indicating that learning is incomplete and/or Toyota Prius vehicle control history (RoB) is stored.

(h) Turn the ignition switch off.

NOTICE:

If the ignition switch is turned to ON for more than 15 seconds with park (P) selected after the zero point of the yaw rate and acceleration sensor has been cleared, only the zero point of the yaw rate sensor will be stored. If the Toyota Prius vehicle is driven under these conditions, the No. 2 skid control ECU (brake actuator assembly) will store the zero point calibration for the acceleration sensor as not being completed. The No. 2 skid control ECU (brake actuator assembly) will then also indicate this as a malfunction of the VSC system using the indicator light.

3. CALIBRATION

NOTICE:

This procedure can be performed only once per trip. For that reason, if it is necessary to perform learning again, turn the ignition switch off for 4 minutes or more before turning the ignition switch to ON again.

HINT:

  • When Dealer Mode (Calibration) is entered, linear solenoid valve offset learning, brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration will be performed automatically.
  • If linear solenoid valve offset learning has not been performed, DTC is stored.
  • If brake pedal stroke sensor assembly zero point calibration has not been performed, DTC is stored.
  • If system information memorization has not been performed, DTC is stored.
  • If yaw rate sensor zero point calibration has not been performed, RoB is stored.
  • If acceleration sensor zero point calibration has not been performed, DTC is stored.

(a) Turn the ignition switch off.

(b) Check that the steering wheel is centered.

(c) Check that park (P) is selected.

(d) Connect the GTS to the DLC3.

(e) Turn the ignition switch to ON.

(f) Check that the parking brake is released.

NOTICE:

  • If the parking brake is not released, linear solenoid valve offset learning cannot be performed.
  • If the parking brake is engaged during linear solenoid valve offset learning, learning will be suspended.

    In this case, learning will resume when the parking brake is released.

  • After replacing the brake actuator assembly, the parking brake indicator light (red) blinks when the ignition switch is turned to ON for the first time. To turn off the parking brake indicator light (red) after replacing the brake actuator assembly, operate the electric parking brake switch (electric parking brake switch assembly) to the lock side then to the release side.

(g) Turn the GTS on.

(h) Switch the skid control ECUs to Dealer Mode (Calibration) using the GTS. Enter the following menus: Chassis / Brake/EPB / Utility / Calibration.

Chassis > Brake/EPB > Utility

Calibration

(i) Wait for approximately 2 minutes with the Toyota Prius vehicle stopped without depressing the brake pedal and confirm that the ABS warning light, brake system warning light (yellow indicator) and slip indicator light flash the Dealer Mode pattern (blinks at 0.25 seconds intervals).

NOTICE:

  • Do not depress the brake pedal when performing "Calibration".
  • If Dealer Mode is entered when the shift position is in a position other than P, DTC is stored.

HINT:

  • An auxiliary battery voltage of 10 V or more is required during learning. If the auxiliary battery voltage drops below 10 V, learning may be canceled. The time required for learning changes depending on the auxiliary battery voltage.
  • If linear solenoid valve offset learning does not complete, DTC will be stored. In this case, perform learning again after clearing the DTC and turning the ignition switch off.
  • After "Calibration" completes, the ABS warning light, brake system warning light (yellow indicator) and slip indicator light flash the Dealer Mode pattern (blinks at 0.25 seconds intervals).

(j) Check that "complete" is displayed for Dealer Mode (Signal Check) Inspection Item "Learning of Stroke Sensor Zero Point".

(k) Turn the ignition switch off.

(l) Disconnect the GTS.