Front Seat Outer Belt Assembly

In this manual: Front Seat Outer Belt Assembly
How To Troubleshoot Ecu Controlled Systems — 1How To Use This Manual — 1Identification Information — 1Repair Instruction — 1Terms — 12zr-fxe Air Cleaner Filter Element — 12zr-fxe Auxiliary Battery — 12zr-fxe Coolant (for Engine Coolant) — 12zr-fxe Oil And Oil Filter — 12zr-fxe Spark Plug — 1Air Conditioning Filter — 1Battery Cooling Filter — 1Brake Fluid — 1Coolant (for Inverter) — 1Front Brake Flexible Hose — 1Front Disc Brake Pad — 1Front Lower Ball Joint — 1Front Wheel Alignment — 1Front Wiper Rubber — 1General Maintenance — 1M20a-fxs Air Cleaner Filter Element — 1M20a-fxs Auxiliary Battery — 1M20a-fxs Coolant (for Engine Coolant) — 1M20a-fxs Oil And Oil Filter — 1M20a-fxs Spark Plug — 1Pa10/pb10/pb12 Hybrid Transaxle Fluid — 1Q810 Hybrid Transaxle Fluid — 1Rear Brake Flexible Hose — 1Rear Disc Brake Pad — 1Rear Wheel Alignment — 1Steering Column — 1Tire And Wheel — 1Transmitter Battery — 1When Disconnecting Or Reconnecting Battery Terminal — 1When Replacing Or Removing/installing Parts — 1Automatic High Beam Main Switch — 1Automatic High Beam System — 1Driver Monitor Camera — 1Driver Monitor Camera System — 1Driver Monitor Ecu — 1Front Camera — 1Front Camera System — 1Front Radar Sensor System — 1Front Side Radar Sensor — 1Front Side Radar Sensor System — 1Millimeter Wave Radar Sensor — 1Utility — 1Advanced Park — 1Advanced Park Main Switch — 1Amplifier Antenna — 1Audio And Visual System — 1Front Door Speaker — 1Instrument Panel Speaker — 1Microphone — 1Noise Filter — 1Pillar Speaker — 1Radio Antenna Cord (for Back Door) — 1Radio Antenna Cord (for Instrument Panel) — 1Radio Antenna Cord (for Roof) — 1Radio Receiver — 1Rear Door Speaker — 1Roof Antenna — 1Stereo Component Amplifier — 1Stereo Jack Adapter Assembly — 1Window Glass Antenna Wire — 1Back-up Battery — 1Dcm(telematics Transceiver) — 1Manual(sos)switch — 1Safety Connect System — 1Telephone And Gps Antenna (for Front Side) — 1Telephone And Gps Antenna (for Roof Side) — 1Telephone And Gps Antenna Cords — 1Garage Door Opener System (for Digital Inner Mirror) — 1Garage Door Opener System (for Ec Inner Mirror) — 1Blind Spot Monitor Sensor — 1Blind Spot Monitor System — 1Clearance Warning Ecu — 1Intuitive Parking Assist System — 1Panoramic View Monitor Switch — 1Panoramic View Monitor System — 1Parking Assist Ecu — 1Parking Assist Light — 1Parking Assist Monitor System — 1Parking Support Brake System — 1Rear View Monitor System — 1Television Camera (for Front) — 1Television Camera (for Rear) — 1Television Camera (for Side) — 1Ultrasonic Sensor (for Front) — 1Ultrasonic Sensor (for Rear) — 1Brake Actuator — 1Brake Pedal Stroke Sensor — 1Electronically Controlled Brake System — 1Front Speed Sensor — 1Rear Speed Sensor (for Awd) — 1Steering Angle Sensor — 1Brake Booster — 1Brake Fluid — 1Brake Line — 1Brake Pedal — 1Brake System — 1Electric Parking Brake Actuator — 1Electric Parking Brake Switch — 1Electric Parking Brake System — 1Forced Release — 1Front Axle Hub — 1Front Axle Hub Bolt — 1Rear Axle Carrier (for 2wd) — 1Rear Axle Carrier (for Awd) — 1Rear Axle Hub (for 2wd) — 1Rear Axle Hub (for Awd) — 1Rear Axle Hub Bolt — 1Steering Knuckle — 1Drive Shaft System — 1Front Drive Shaft Assembly — 1Rear Drive Shaft Assembly — 1Combination Switch — 1Electronic Shift Lever System — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Oil Seal — 1Hybrid Transaxle System — 1Input Shaft Oil Seal — 1Motor Cable — 1Pa10 Hybrid Vehicle Transaxle — 1Pa10 Manual Parking Lock Release — 1Pa10 Oil Cooler — 1Pb10/pb12 Hybrid Vehicle Transaxle — 1Pb10/pb12 Manual Parking Lock Release — 1Pb10/pb12 Oil Cooler — 1Shift Control Actuator — 1Shift Lever — 1Shift Lever Knob — 1Differential Side Gear Shaft — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Side Gear Oil Seal — 1Motor Cable — 1Rear Traction Motor — 1Coolant (for Engine) — 1Cooling Fan Motor — 1Cooling Fan System — 1Radiator — 1Relay — 1Thermostat — 1Water Pump — 1Canister — 1Egr Cooler — 1Egr Valve — 1Emission Control System — 1Fuel Tank Cap — 1Pcv Valve — 1Purge Valve — 1Vacuum Sensor — 1Air Fuel Ratio Sensor — 1Camshaft Oil Control Valve — 1Camshaft Position Sensor — 1Crankshaft Position Sensor — 1Ecm — 1Engine Coolant Temperature Sensor — 1Heated Oxygen Sensor — 1Ignition Coil And Spark Plug — 1Ignition System — 1Knock Sensor — 1Mass Air Flow Meter — 1Relay — 1Sfi System — 1Throttle Body — 1Camshaft — 1Cylinder Block — 1Cylinder Head — 1Cylinder Head Gasket — 1Engine — 1Engine Assembly — 1Engine Unit — 1Front Crankshaft Oil Seal — 1Rear Crankshaft Oil Seal — 1Fuel Filter — 1Fuel Injector — 1Fuel Pressure Regulator — 1Fuel Pump — 1Fuel Sender Gauge Assembly — 1Fuel System — 1Fuel Tank — 1Air Cleaner Filter Element — 1Exhaust Manifold — 1Exhaust Pipe — 1Intake Manifold — 1Intake System — 1Lubrication System — 1Oil And Oil Filter — 1Oil Pan And Oil Level Sensor — 1Oil Pressure Switch — 1Oil Pump — 1Accelerator Pedal Sensor — 1Battery Blower (for Hev Model) — 1Battery Ecu (for Hev Model) — 1Battery Ecu (for Phev Model) — 1Battery Voltage Sensor (for Phev Model) — 1Charge Cable (for Phev Model) — 1Charge Indicator (for Phev Model) — 1Charge Inlet (for Phev Model) — 1Combination Switch — 1Coolant (for Inverter) — 1Cooler (for Phev Model) — 1Electric Vehicle Charger Assembly (for Phev Model) — 1Frame Wire (for Hev Model) — 1Frame Wire (for Phev Model) — 1Heater Relay (for Phev Model) — 1Hv Battery (for Hev Model) — 1Hv Battery (for Phev Model) — 1Hv Battery Heater (for Phev Model) — 1Hv Battery Stack (for Phev Model) — 1Hv Relay Assembly (for Hev Model) — 1Hv Relay Assembly (for Phev Model) — 1Hybrid Battery System (for 2zr-fxe) — 1Hybrid Battery System (for M20a-fxs) — 1Hybrid Battery System (for Phev Model) — 1Hybrid Vehicle Control Ecu — 1Inverter With Converter (for Hev Model) — 1Motor Generator Control System (for 2zr-fxe) — 1Plug-in Charge Control System (for Phev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Service Plug Grip (for Hev Model) — 1Sub Radiator — 1Water Pump With Motor — 1Auxiliary Battery — 1Battery Current Sensor — 1Charging System — 1Solar Charging System — 1Solar Control Unit — 1Solar Roof — 1Can Communication System (for Hev Model) — 1Lin Communication System — 1Network Gateway Ecu — 1Integration Control Supply — 1Main Body Ecu — 1Power Integration System — 1Sub Battery System — 1Power Steering Ecu — 1Power Steering System — 1Heated Steering Wheel Controller — 1Heated Steering Wheel System — 1Steering Column Assembly — 1Steering Heater Switch — 1Steering Pad Switch — 1Steering System — 1Steering Wheel — 1Front Lower Ball Joint — 1Front Lower Suspension Arm (for 2zr-fxe Lh Side) — 1Front Lower Suspension Arm (for 2zr-fxe Rh Side) — 1Front Lower Suspension Arm (for M20a-fxs) — 1Front Shock Absorber — 1Front Stabilizer Bar — 1Front Suspension Member — 1Rear Coil Spring — 1Rear Lower Arm (for Awd Lh Side) — 1Rear Lower Arm (for Awd Rh Side) — 1Rear Lower Arm (for Hev Model 2wd) — 1Rear Lower Arm (for Phev Model) — 1Rear Shock Absorber — 1Rear Stabilizer Bar — 1Rear Suspension Member (for 2wd) — 1Rear Suspension Member (for Awd) — 1Rear Trailing Arm — 1Rear Upper Arm — 1Tire And Wheel System — 1Tire Repair Seal — 1Tire Pressure Warning Receiver — 1Tire Pressure Warning System — 1Tire Pressure Warning Valve — 1Acoustic Vehicle Alerting System — 1Vehicle Approaching Speaker — 1Vehicle Approaching Speaker Ecu — 1Back Door — 1Back Door Closer Ecu — 1Back Door Opener Switch — 1Back Door Support — 1Back Door Weatherstrip — 1Charge Lid Courtesy Switch — 1Charge Lid Opener Motor Assembly — 1Charge Lid Opener System — 1Charge Lid Opener Unit — 1Front Door — 1Front Door Opening Trim Weatherstrip — 1Fuel Lid Opener Motor Assembly — 1Fuel Lid Opener Switch — 1Fuel Lid Opener System — 1Hood — 1Hood Lock Control Cable Assembly — 1Power Back Door Closer Switch — 1Power Back Door Control Switch — 1Power Back Door Drive Unit — 1Power Back Door System — 1Power Back Door Touch Sensor — 1Power Back Door Warning Buzzer — 1Rear Door — 1Rear Door Opening Trim Weatherstrip — 1Reserve Lock Switch — 1Front Bumper — 1Front Door Belt Moulding — 1Front Door Window Frame Moulding — 1Front Fender — 1Front Pillar Upper Cover — 1Grille Shutter — 1Grille Shutter System — 1Name Plate — 1Quarter Garnish — 1Rear Bumper — 1Rear Door Belt Moulding — 1Rear Door Window Frame Moulding — 1Rear Wheel House Plate — 1Rocker Panel Moulding — 1Roof Drip Side Finish Moulding — 1Roof Garnish — 1Wheel Opening Moulding (for Front Side) — 1Wheel Opening Moulding (for Rear Side) — 1Windshield Outside Moulding — 1Horn — 1Horn System — 1Relay — 1Automatic Light Control Sensor — 1Back-up Light Assembly — 1Charge Lid Light — 1Front Marker Light — 1Hazard Warning Switch — 1Headlight Assembly — 1Headlight Dimmer Switch — 1Headlight Leveling Switch — 1High Mounted Stop Light Assembly — 1Illumination Light Assembly — 1License Plate Light Assembly — 1Lighting System — 1Rear Combination Light Assembly — 1Rear Light Assembly — 1Rear Side Marker Light Assembly — 1Relay — 1Side Turn Signal Light Assembly — 1Stop Light Switch — 1Switch Housing — 1Outer Mirror Switch — 1Outer Rear View Mirror — 1Outer Rear View Mirror Cover — 1Outer Rear View Mirror Glass — 1Power Mirror Control System — 1Back Door Glass — 1Front Passenger Side Power Window Switch — 1Power Window Control System — 1Power Window Master Switch — 1Power Window Regulator Motor (for Front Door) — 1Power Window Regulator Motor (for Rear Door) — 1Rear Power Window Switch — 1Relay — 1Roof Window Fix Glass — 1Window Defogger System — 1Windshield Deicer Switch — 1Windshield Deicer System — 1Windshield Glass — 1Front Wiper Motor — 1Rain Sensor — 1Relay — 1Washer Motor — 1Washer Nozzle (for Front Side) — 1Washer Nozzle (for Rear Television Camera) — 1Wiper And Washer System — 1Wiper Ecu — 1Wiper Switch — 1Back Door Lock — 1Door Control Receiver — 1Door Control Switch — 1Door Control Transmitter — 1Door Lock Release Motor (for Rear Side) — 1Door Outside Handle (for Rear Side) — 1Front Door Lock — 1Power Door Lock Control System — 1Rear Door Lock — 1Transmitter Battery — 1Wireless Door Lock Control System — 1Accumulator — 1Air Conditioning Amplifier — 1Air Conditioning Panel — 1Air Conditioning Pressure Sensor — 1Air Conditioning Unit — 1Ambient Temperature Sensor — 1Blower Unit — 1Condenser (for Hev Model) — 1Condenser (for Phev Model) — 1Discharge Temperature Sensor — 1Electric Expansion Valve (cooling) — 1Electric Expansion Valve (heating) — 1Evaporator Pipe Temperature Sensor — 1Evaporator Pressure Regulator — 1Front Blower Motor — 1Front Evaporator Front Solenoid Valve — 1Air Conditioning System (for Hev Model) — 1Front Evaporator Temperature Sensor — 1Heat Exchanger Temperature Sensor — 1Heat Pump Ecu — 1High Pressure Magnetic Valve — 1Humidity Sensor — 1Internal Condenser Temperature Sensor — 1Low Pressure Magnetic Valve — 1Refrigerant (for Hfc-134a(r134a)) — 1Refrigerant Line (for Hev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Room Temperature Sensor — 1Solar Sensor — 1Floor Carpet — 1Front Console Box — 1Instrument Panel Safety Pad — 1Roof Headlining — 1Roof Sunshade — 1Ambient Light (for Driver Side) — 1Ambient Light (for Front Passenger Side) — 1Back Door Courtesy Switch — 1Footwell Light — 1Glove Box Light — 1Lighting System — 1Luggage Compartment Room Light — 1Personal Light — 1Room Light — 1Vanity Light — 1Vanity Light Switch — 1Combination Meter — 1Meter / Gauge System — 1Trip Switch — 1Digital Inner Mirror — 1Digital Rear-view Mirror System — 1Inner Mirror Monitor Camera — 1Inner Rear View Mirror (w/o Ec Mirror) — 1Accessory Power Outlet System — 1Power Outlet Socket (for Console Box Front Side) — 1Power Outlet Socket (for Console Box Rear Side) — 1Power Outlet Socket (for Console Box) — 1Power Outlet Socket (for Luggage Compartment) — 1Power Outlet Switch — 1Wireless Charger Assembly — 1Wireless Charging System — 1Climate Control Seat System — 1Front Power Seat Control System (w/ Memory) — 1Front Power Seat Motor Assembly — 1Front Seat Assembly (for Power Seat) — 1Front Seat Cushion Heater (for Power Seat) — 1Front Seatback Heater (for Power Seat) — 1Lumbar Support Adjuster Assembly — 1Power Seat Control Ecu — 1Power Seat Switch — 1Power Seat Track Rail Assembly — 1Rear Seat Assembly — 1Rear Seat Cushion Heater — 1Rear Seat Reminder System — 1Rear Seatback Heater — 1Seat Heater Control — 1Seat Heater Switch (for Front Seat) — 1Seat Heater Switch (for Rear Side) — 1Seat Heater System — 1Seat Memory Switch — 1Child Restraint Seat Anchor Bracket — 1Front Seat Inner Belt Assembly — 1Front Seat Outer Belt Assembly — 1Occupant Detection Sensor (for Front Passenger Side) — 1Rear Center Seat Outer Belt Assembly — 1Rear Seat Inner Belt Assembly (for Rh Side) — 1Rear Seat Outer Belt Assembly — 1Seat Belt Warning System (w/ Occupant Classification System) — 1Tongue Plate Stopper — 1Airbag System — 1Center Airbag Sensor Assembly — 1Curtain Shield Airbag Assembly — 1Front Airbag Sensor — 1Front Passenger Airbag Assembly — 1Front Seat Side Airbag Assembly — 1Inspection After Collision — 1Knee Airbag Assembly — 1Occupant Classification System — 1Rear Seat Side Airbag Assembly — 1Side Airbag Sensor (for Center Pillar) — 1Side Airbag Sensor (for Front Door) — 1Spiral Cable — 1Steering Pad — 1Certification Ecu — 1Digital Key Ecu — 1Digital Key Receiver (for Front Floor) — 1Digital Key Receiver (for Outside Luggage Compartment) — 1Digital Key Receiver (for Rear Door) — 1Digital Key System — 1Electrical Key Oscillator (for Front Floor) — 1Electrical Key Oscillator (for Outside Luggage Compartment) — 1Electrical Key Oscillator (for Rear Floor) — 1Engine Hood Courtesy Switch — 1Id Code Box — 1Smart Key System (for Start Function) — 1
~19min read
4special tools
0204060801004231N·mlb·ft
Tightening torque found on this page
  • Precaution
  • Removal
  • Inspection
  • Installation
  • Disposal

Precaution

PRECAUTION

CAUTION:

Replace any faulty parts of the seat belt systems (outer belt, inner belt, bolts, nuts, adjustable shoulder anchor, tether anchor hardware and other related parts). When inspecting a vehicle that has been involved in a collision, be sure to check all of the seat belt systems regardless of whether or not the system was activated in the collision. Replace any damaged or malfunctioning systems.

ROAD TEST (IN SAFE AREA)

CAUTION:

Conduct this test in a safe area.

(a) Fasten the front seat belts.

(b) Drive the Toyota Prius vehicle at 16 km/h and firmly depress the brake pedal. Check that the front seat outer belt assemblies lock and cannot be extended.

If a front seat outer belt assembly does not lock, replace it.

Click here

HINT:

Inspect the seat belt assembly before installing it.

Click here

Removal

REMOVAL

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front seat outer belt assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.
w/ Occupant Classification System:
  • Front passenger seat*

Zero point calibration (Occupant classification system)

  • Occupant Classification System
  • Passenger airbag ON/OFF indicator
  • Airbag System (Front passenger side)
  • Seat Belt Warning System (Front passenger)

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

Learning completes when Toyota Prius vehicle is driven

Effect/Inoperative Function when Necessary Procedure not Performed

Necessary Procedure

Link

Front Camera System

Drive the Toyota Prius vehicle straight ahead at 35 km/h or more for 5 seconds or more.

Learning completes when vehicle is operated normally

Effect/Inoperative Function when Necessary Procedure not Performed

Necessary Procedure

Link

*1: w/o Power Back Door System

*2: w/ Power Back Door System

Power Door Lock Control System*1

  • Back door opener

Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.

Power Back Door System*2

Reset back door close position

Air Conditioning System

for HEV Model:
  • After the ignition switch is turned to ON, the servo motor standard position is recognized.
for PHEV Model:
  • After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized.

-

COMPONENTS (REMOVAL)

Procedure

Part Name Code

1

PRECAUTION

-

-

-

2

BATTERY SERVICE HOLE COVER ASSEMBLY

58440

-

-

3

DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

-

-

-

-

*A

for M20A-FXS

-

-

*a

HINT:

As the illustration shown is an example, the actual details may differ.

-

-

Procedure

Part Name Code

4

FRONT DOOR SCUFF PLATE

67914

-

-

-

5

FRONT DOOR OPENING TRIM WEATHERSTRIP

62312B

-

-

-

6

REAR DOOR SCUFF PLATE INSIDE

67918F

-

-

-

7

REAR DOOR OPENING TRIM WEATHERSTRIP

62332A

-

-

-

8

LAP BELT OUTER ANCHOR COVER

73233

-

-

-

9

DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY

73220

-

-

-

10

CENTER PILLAR LOWER GARNISH

62414A

-

-

-

11

CENTER PILLER GARNISH ASSEMBLY

62420A

-

-

-

12

REMOVE FRONT SEAT OUTER BELT ASSEMBLY

73220

-

-

13

FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY

73200A

-

-

-

PROCEDURE

1. PRECAUTION

CAUTION:

Be sure to read Precaution thoroughly before servicing.

NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click here

2. REMOVE BATTERY SERVICE HOLE COVER ASSEMBLY (for M20A-FXS)

Click here

3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

(a) for M20A-FXS:

Click here

(b) for 2ZR-FXE:

Click here

4. REMOVE FRONT DOOR SCUFF PLATE

Click here

5. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP

6. REMOVE REAR DOOR SCUFF PLATE INSIDE

Click here

7. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

8. REMOVE LAP BELT OUTER ANCHOR COVER

9. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY

10. REMOVE CENTER PILLAR LOWER GARNISH

Click here

11. REMOVE CENTER PILLER GARNISH ASSEMBLY

Click here

12. REMOVE FRONT SEAT OUTER BELT ASSEMBLY

(1) Remove the nut and disconnect the shoulder anchor of the front seat outer belt assembly.

(2) Using a screwdriver with its tip wrapped with protective tape, pull out the locking button as shown in the illustration to release the lock and disconnect the pretensioner connector.

(3) Remove the 2 bolts.

(4) Disengage the 2 guides to remove the front seat outer belt assembly.

13. REMOVE FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY

HINT:

Perform this procedure only when replacement of the front shoulder belt anchor adjuster assembly is necessary.

Inspection

INSPECTION

PROCEDURE

1. INSPECT FRONT SEAT OUTER BELT ASSEMBLY

(a) Before installing the front seat outer belt assembly, check the ELR function.

NOTICE:

Do not disassemble the retractor.

(1) When the inclination of the retractor is 15° or less, check that the belt can be pulled from the retractor. When the inclination of the retractor is over 45°, check that the belt locks. If the result is not as specified, replace the front seat outer belt assembly.

*a

Unlock

*b

Lock

*c

45°

Installation

INSTALLATION

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:

  • Use the same procedure for the RH side and LH side.
  • The procedure listed below is for the LH side.
COMPONENTS (INSTALLATION)

Procedure

Part Name Code

1

FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY

73200A

-

-

2

INSTALL FRONT SEAT OUTER BELT ASSEMBLY

73220

-

-

3

CENTER PILLER GARNISH ASSEMBLY

62420A

-

-

-

4

CENTER PILLAR LOWER GARNISH

62414A

-

-

-

5

CONNECT FRONT SEAT OUTER BELT ASSEMBLY

73220

-

-

-

6

LAP BELT OUTER ANCHOR COVER

73233

-

-

-

7

REAR DOOR OPENING TRIM WEATHERSTRIP

62332A

-

-

-

8

REAR DOOR SCUFF PLATE INSIDE

67918F

-

-

-

9

FRONT DOOR OPENING TRIM WEATHERSTRIP

62312B

-

-

-

10

FRONT DOOR SCUFF PLATE

67914

-

-

-

Tightening torque for "Major areas involving basic Toyota Prius vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf)

N*m (kgf*cm, ft.*lbf): Specified torque

Procedure

Part Name Code

11

CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

-

-

-

-

12

BATTERY SERVICE HOLE COVER ASSEMBLY

58440

-

-

-

13

INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

-

-

-

14

INSPECT SRS WARNING LIGHT

-

-

-

15

INSPECT SEAT BELT WARNING SYSTEM

-

-

-

*A

for M20A-FXS

-

-

*a

HINT:

As the illustration shown is an example, the actual details may differ.

-

-

PROCEDURE

1. INSTALL FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY

HINT:

Perform this procedure only when replacement of the front shoulder belt anchor adjuster assembly is necessary.

(1) Engage the guide and temporarily install the front shoulder belt anchor adjuster assembly with the 2 bolts.

(2) Fully tighten the bolt (A) and then the bolt (B) to install the front shoulder belt anchor adjuster assembly.

Torque:

42 N·m {428 kgf·cm, 31 ft·lbf}

2. INSTALL FRONT SEAT OUTER BELT ASSEMBLY

(1) Engage the 2 guides and install the front seat outer belt assembly with the bolt.

Torque:

12,5 N·m {127 kgf·cm, 9 ft·lbf}

(2) Connect the pretensioner connector and lock the locking button as shown in the illustration.

NOTICE:

Securely lock the locking button.

(3) Connect the shoulder anchor of the front seat outer belt assembly with the nut.

Torque:

42 N·m {428 kgf·cm, 31 ft·lbf}

(1) Install the front seat outer belt assembly with the bolt.

Torque:

42 N·m {428 kgf·cm, 31 ft·lbf}

(2) Check that the ELR locks.

NOTICE:

This check should be performed with the front seat outer belt assembly installed to the Toyota Prius vehicle.

1. With the front seat outer belt assembly installed to the vehicle, check that the belt locks when it is pulled out quickly.

3. INSTALL CENTER PILLER GARNISH ASSEMBLY

4. INSTALL CENTER PILLAR LOWER GARNISH

5. CONNECT FRONT SEAT OUTER BELT ASSEMBLY

Torque:

42 N·m {428 kgf·cm, 31 ft·lbf}

6. INSTALL LAP BELT OUTER ANCHOR COVER

7. CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

8. INSTALL REAR DOOR SCUFF PLATE INSIDE

9. CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP

10. INSTALL FRONT DOOR SCUFF PLATE

11. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

(a) for M20A-FXS:

Click here

(b) for 2ZR-FXE:

Click here

12. INSTALL BATTERY SERVICE HOLE COVER ASSEMBLY (for M20A-FXS)

13. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click here

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click here

14. INSPECT SRS WARNING LIGHT

Click here

15. INSPECT SEAT BELT WARNING SYSTEM

(a) w/o Occupant Classification System:

Click here

(b) w/ Occupant Classification System:

Click here

Disposal

DISPOSAL

CAUTION:

Before performing pre-disposal deployment of any SRS part, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.

PROCEDURE

1. PRECAUTION

CAUTION:

  • Use gloves and safety glasses when handling a front seat outer belt assembly with a deployed pretensioner.
  • Always wash your hands with water after completing the operation.
  • Do not apply water, etc. to a front seat outer belt assembly with a deployed pretensioner.
  • When deploying a seat belt pretensioner, always use the specified SST (SRS airbag deployment tool). Perform the operation in a place away from electrical noise.
  • Never dispose of a front seat outer belt assembly with a pretensioner that has not been deployed.
  • The front seat outer belt assembly produces an exploding sound when the pretensioner is deployed, so perform the operation outdoors where it will not disturb nearby residents.
  • When deploying a seat belt pretensioner, perform the operation at least 10 m (32.8 ft.) away from the Toyota Prius vehicle.

HINT:

When scrapping a vehicle equipped with a seat belt pretensioner or disposing of a front seat outer belt assembly with a seat belt pretensioner, always deploy the seat belt pretensioner first in accordance with the procedure described below. If any abnormality occurs during deployment of the seat belt pretensioner, contact the SERVICE DEPARTMENT of the distributor.

2. DISPOSE OF FRONT SEAT OUTER BELT ASSEMBLY (When Installed to Toyota Prius Vehicle)

NOTICE:

  • When disposing of a front seat outer belt assembly with a pretensioner, never deploy the pretensioner in the customer's vehicle.
  • Be sure to observe the following procedure when deploying a seat belt pretensioner.

HINT:

Prepare an auxiliary battery as the power source to deploy the seat belt pretensioner.

(a) Check the function of SST.

SST: 09082-00700

CAUTION:

When deploying a seat belt pretensioner, always use the specified SST.

(1) Connect the red clip of SST to the positive ( ) auxiliary battery terminal and the black clip to the negative (-) auxiliary battery terminal.

HINT:

At this time, do not connect the yellow connector. It will be connected to the seat belt pretensioner in a later step.

*a

Auxiliary Battery

(2) Press the SST activation switch and check that the LED of the SST activation switch illuminates.

CAUTION:

If the LED is illuminated when the SST activation switch is not pressed, SST may be malfunctioning. In this case, do not use the malfunctioning SST.

(b) Refer to Precaution.

Click here

(c) Remove the battery service hole cover assembly (for M20A-FXS).

Click here

(d) Disconnect the cable from the negative (-) auxiliary battery terminal.

1. for M20A-FXS:

Click here

2. for 2ZR-FXE:

Click here

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

(e) Disconnect the seat belt pretensioner connector.

(1) Remove the center pillar lower garnish.

Click here

(2) Using a screwdriver, pull out the locking button as shown in the illustration to release the lock and disconnect the pretensioner connector.

HINT:

Tape the screwdriver tip before use.

*a

Protective Tape

*b

Locking Button

*c

Release

(f) Connect SST.

(1) After connecting the following SST to each other, connect them to the seat belt pretensioner.

SST: 09082-00700

SST: 09082-00802

09082-10801

09082-20801

NOTICE:

To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the pretensioner connector.

(2) Move SST at least 10 m (32.8 ft.) away from the front of the Toyota Prius vehicle.

*a

Auxiliary Battery

*b

10 m (32.8 ft.) or more

CAUTION:

  • Do not perform deployment with any of the doors or windows open.
  • If deployment is performed with any of the doors or windows open, dust and gas may enter the eyes or be breathed in.

(3) Close all of the doors and windows of the Toyota Prius vehicle.

NOTICE:

Do not damage the SST wire harness.

(g) Deploy the seat belt pretensioner.

(1) Check that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.

(2) Connect the red clip of SST to the positive ( ) auxiliary battery terminal and the black clip to the negative (-) auxiliary battery terminal.

(3) Press the SST activation switch to deploy the seat belt pretensioner.

CAUTION:

  • The front seat outer belt assembly produces an exploding sound when the pretensioner is deployed, so perform the operation outdoors where it will not disturb nearby residents.
  • If this procedure is performed indoors or on a rough road where safety cannot be ensured, unforeseen injuries may occur. Also, if this procedure is performed near a residential area, the deployment noise may disturb nearby residents.

HINT:

The seat belt pretensioner will deploy at the same time as the LED of SST illuminates.

(h) Dispose of the front seat outer belt assembly.

(1) Remove the front seat outer belt assembly and SST.

(2) Place the front seat outer belt assembly in a plastic bag, tie the end tightly, and dispose of it in the same way as other general parts.

CAUTION:

  • The front seat outer belt assembly becomes extremely hot when the pretensioner is deployed, so do not touch it for at least 30 minutes after deployment.
  • Do not apply water, etc. to a front seat outer belt assembly with a deployed pretensioner.
  • If water is applied to the front seat outer belt assembly immediately after deployment, burns may be caused by the resulting steam.
  • Always wear safety glasses and gloves when handling a front seat outer belt assembly with a deployed pretensioner.
  • If a front seat outer belt assembly with a deployed pretensioner is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.
  • After removal, quickly seal the front seat outer belt assembly in a plastic bag.
  • Never dispose of a front seat outer belt assembly with a pretensioner that has not been deployed.
  • If a front seat outer belt assembly with a pretensioner that has not been deployed is disposed of, and then deploys accidentally, unforeseen injuries may occur.
  • Always wash your hands with water after completing the operation.

HINT:

When scrapping a Toyota Prius vehicle, deploy the seat belt pretensioners, and then scrap the vehicle with the front seat outer belt assemblies installed.

3. DISPOSE OF FRONT SEAT OUTER BELT ASSEMBLY (When not Installed to Vehicle)

NOTICE:

  • When disposing of a front seat outer belt assembly with a pretensioner, never deploy the pretensioner in the customer's Toyota Prius vehicle.
  • Be sure to observe the following procedure when deploying a seat belt pretensioner.

HINT:

Prepare an auxiliary battery as the power source to deploy the seat belt pretensioner.

(a) Check the function of SST.

Click here

SST: 09082-00700

CAUTION:

When deploying a seat belt pretensioner, always use the specified SST.

(1) Connect the red clip of SST to the positive ( ) auxiliary battery terminal and the black clip to the negative (-) auxiliary battery terminal.

HINT:

At this time, do not connect the yellow connector. It will be connected to the seat belt pretensioner in a later step.

*a

Auxiliary Battery

(2) Press the SST activation switch and check that the LED of the SST activation switch illuminates.

CAUTION:

If the LED is illuminated when the SST activation switch is not pressed, SST may be malfunctioning. In this case, do not use the malfunctioning SST.

(b) Refer to Precaution.

Click here

(c) Remove the front seat outer belt assembly.

Click here

(d) Wind the seat belt webbing with the retractor.

*a

Cut

*b

100 mm (3.94 in.)

(e) When the seat belt webbing is sufficiently wound, cut the seat belt webbing approximately 100 mm (3.94 in.) from the retractor, as shown in the illustration.

HINT:

The retractor resistance increases in proportion with how much the seat belt webbing is wound.

(f) Connect SST.

(1) After connecting the following SST to each other, connect them to the seat belt pretensioner.

SST: 09082-00700

SST: 09082-00802

09082-10801

09082-20801

NOTICE:

To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the pretensioner connector.

(2) Place the front seat outer belt assembly on the ground and cover it with an unneeded tire and wheel assembly.

NOTICE:

  • Position the front seat outer belt assembly as shown in the illustration.
  • The tire and wheel assembly may be damaged by the seat belt pretensioner deployment, so use an unneeded tire and wheel assembly.

(3) Position and hold SST at least 10 m (32.8 ft.) away from the tire and wheel assembly.

NOTICE:

Do not damage the SST wire harness.

(g) Deploy the seat belt pretensioner.

*a

Auxiliary Battery

*b

10 m (32.8 ft.) or more

(1) Check that no one is within a 10 m (32.8 ft.) radius of the tire and wheel assembly.

(2) Connect the red clip of SST to the positive ( ) auxiliary battery terminal and the black clip to the negative (-) auxiliary battery terminal.

(3) Press the SST activation switch to deploy the seat belt pretensioner.

CAUTION:

  • The front seat outer belt assembly produces an exploding sound when the pretensioner is deployed, so perform the operation outdoors where it will not disturb nearby residents.
  • If this procedure is performed indoors or on a rough road where safety cannot be ensured, unforeseen injuries may occur. Also, if this procedure is performed near a residential area, the deployment noise may disturb nearby residents.

HINT:

The seat belt pretensioner will deploy at the same time as the LED of SST illuminates.

(h) Dispose of the front seat outer belt assembly.

(1) Remove the tire and wheel assembly and SST.

(2) Place the front seat outer belt assembly in a plastic bag, tie the end tightly, and dispose of it in the same way as other general parts.

CAUTION:

  • The front seat outer belt assembly becomes extremely hot when the pretensioner is deployed, so do not touch it for at least 30 minutes after deployment.
  • Do not apply water, etc. to a front seat outer belt assembly with a deployed pretensioner.
  • If water is applied to the front seat outer belt assembly immediately after deployment, burns may be caused by the resulting steam.
  • Always wear safety glasses and gloves when handling a front seat outer belt assembly with a deployed pretensioner.
  • If a front seat outer belt assembly with a deployed pretensioner is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.
  • After removal, quickly seal the front seat outer belt assembly in a plastic bag.
  • Never dispose of a front seat outer belt assembly with a pretensioner that has not been deployed.
  • If a front seat outer belt assembly with a pretensioner that has not been deployed is disposed of, and then deploys accidentally, unforeseen injuries may occur.
  • Always wash your hands with water after completing the operation.