Engine Unit

In this manual: Engine Unit
How To Troubleshoot Ecu Controlled Systems — 1How To Use This Manual — 1Identification Information — 1Repair Instruction — 1Terms — 12zr-fxe Air Cleaner Filter Element — 12zr-fxe Auxiliary Battery — 12zr-fxe Coolant (for Engine Coolant) — 12zr-fxe Oil And Oil Filter — 12zr-fxe Spark Plug — 1Air Conditioning Filter — 1Battery Cooling Filter — 1Brake Fluid — 1Coolant (for Inverter) — 1Front Brake Flexible Hose — 1Front Disc Brake Pad — 1Front Lower Ball Joint — 1Front Wheel Alignment — 1Front Wiper Rubber — 1General Maintenance — 1M20a-fxs Air Cleaner Filter Element — 1M20a-fxs Auxiliary Battery — 1M20a-fxs Coolant (for Engine Coolant) — 1M20a-fxs Oil And Oil Filter — 1M20a-fxs Spark Plug — 1Pa10/pb10/pb12 Hybrid Transaxle Fluid — 1Q810 Hybrid Transaxle Fluid — 1Rear Brake Flexible Hose — 1Rear Disc Brake Pad — 1Rear Wheel Alignment — 1Steering Column — 1Tire And Wheel — 1Transmitter Battery — 1When Disconnecting Or Reconnecting Battery Terminal — 1When Replacing Or Removing/installing Parts — 1Automatic High Beam Main Switch — 1Automatic High Beam System — 1Driver Monitor Camera — 1Driver Monitor Camera System — 1Driver Monitor Ecu — 1Front Camera — 1Front Camera System — 1Front Radar Sensor System — 1Front Side Radar Sensor — 1Front Side Radar Sensor System — 1Millimeter Wave Radar Sensor — 1Utility — 1Advanced Park — 1Advanced Park Main Switch — 1Amplifier Antenna — 1Audio And Visual System — 1Front Door Speaker — 1Instrument Panel Speaker — 1Microphone — 1Noise Filter — 1Pillar Speaker — 1Radio Antenna Cord (for Back Door) — 1Radio Antenna Cord (for Instrument Panel) — 1Radio Antenna Cord (for Roof) — 1Radio Receiver — 1Rear Door Speaker — 1Roof Antenna — 1Stereo Component Amplifier — 1Stereo Jack Adapter Assembly — 1Window Glass Antenna Wire — 1Back-up Battery — 1Dcm(telematics Transceiver) — 1Manual(sos)switch — 1Safety Connect System — 1Telephone And Gps Antenna (for Front Side) — 1Telephone And Gps Antenna (for Roof Side) — 1Telephone And Gps Antenna Cords — 1Garage Door Opener System (for Digital Inner Mirror) — 1Garage Door Opener System (for Ec Inner Mirror) — 1Blind Spot Monitor Sensor — 1Blind Spot Monitor System — 1Clearance Warning Ecu — 1Intuitive Parking Assist System — 1Panoramic View Monitor Switch — 1Panoramic View Monitor System — 1Parking Assist Ecu — 1Parking Assist Light — 1Parking Assist Monitor System — 1Parking Support Brake System — 1Rear View Monitor System — 1Television Camera (for Front) — 1Television Camera (for Rear) — 1Television Camera (for Side) — 1Ultrasonic Sensor (for Front) — 1Ultrasonic Sensor (for Rear) — 1Brake Actuator — 1Brake Pedal Stroke Sensor — 1Electronically Controlled Brake System — 1Front Speed Sensor — 1Rear Speed Sensor (for Awd) — 1Steering Angle Sensor — 1Brake Booster — 1Brake Fluid — 1Brake Line — 1Brake Pedal — 1Brake System — 1Electric Parking Brake Actuator — 1Electric Parking Brake Switch — 1Electric Parking Brake System — 1Forced Release — 1Front Axle Hub — 1Front Axle Hub Bolt — 1Rear Axle Carrier (for 2wd) — 1Rear Axle Carrier (for Awd) — 1Rear Axle Hub (for 2wd) — 1Rear Axle Hub (for Awd) — 1Rear Axle Hub Bolt — 1Steering Knuckle — 1Drive Shaft System — 1Front Drive Shaft Assembly — 1Rear Drive Shaft Assembly — 1Combination Switch — 1Electronic Shift Lever System — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Oil Seal — 1Hybrid Transaxle System — 1Input Shaft Oil Seal — 1Motor Cable — 1Pa10 Hybrid Vehicle Transaxle — 1Pa10 Manual Parking Lock Release — 1Pa10 Oil Cooler — 1Pb10/pb12 Hybrid Vehicle Transaxle — 1Pb10/pb12 Manual Parking Lock Release — 1Pb10/pb12 Oil Cooler — 1Shift Control Actuator — 1Shift Lever — 1Shift Lever Knob — 1Differential Side Gear Shaft — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Side Gear Oil Seal — 1Motor Cable — 1Rear Traction Motor — 1Coolant (for Engine) — 1Cooling Fan Motor — 1Cooling Fan System — 1Radiator — 1Relay — 1Thermostat — 1Water Pump — 1Canister — 1Egr Cooler — 1Egr Valve — 1Emission Control System — 1Fuel Tank Cap — 1Pcv Valve — 1Purge Valve — 1Vacuum Sensor — 1Air Fuel Ratio Sensor — 1Camshaft Oil Control Valve — 1Camshaft Position Sensor — 1Crankshaft Position Sensor — 1Ecm — 1Engine Coolant Temperature Sensor — 1Heated Oxygen Sensor — 1Ignition Coil And Spark Plug — 1Ignition System — 1Knock Sensor — 1Mass Air Flow Meter — 1Relay — 1Sfi System — 1Throttle Body — 1Camshaft — 1Cylinder Block — 1Cylinder Head — 1Cylinder Head Gasket — 1Engine — 1Engine Assembly — 1Engine Unit — 1Front Crankshaft Oil Seal — 1Rear Crankshaft Oil Seal — 1Fuel Filter — 1Fuel Injector — 1Fuel Pressure Regulator — 1Fuel Pump — 1Fuel Sender Gauge Assembly — 1Fuel System — 1Fuel Tank — 1Air Cleaner Filter Element — 1Exhaust Manifold — 1Exhaust Pipe — 1Intake Manifold — 1Intake System — 1Lubrication System — 1Oil And Oil Filter — 1Oil Pan And Oil Level Sensor — 1Oil Pressure Switch — 1Oil Pump — 1Accelerator Pedal Sensor — 1Battery Blower (for Hev Model) — 1Battery Ecu (for Hev Model) — 1Battery Ecu (for Phev Model) — 1Battery Voltage Sensor (for Phev Model) — 1Charge Cable (for Phev Model) — 1Charge Indicator (for Phev Model) — 1Charge Inlet (for Phev Model) — 1Combination Switch — 1Coolant (for Inverter) — 1Cooler (for Phev Model) — 1Electric Vehicle Charger Assembly (for Phev Model) — 1Frame Wire (for Hev Model) — 1Frame Wire (for Phev Model) — 1Heater Relay (for Phev Model) — 1Hv Battery (for Hev Model) — 1Hv Battery (for Phev Model) — 1Hv Battery Heater (for Phev Model) — 1Hv Battery Stack (for Phev Model) — 1Hv Relay Assembly (for Hev Model) — 1Hv Relay Assembly (for Phev Model) — 1Hybrid Battery System (for 2zr-fxe) — 1Hybrid Battery System (for M20a-fxs) — 1Hybrid Battery System (for Phev Model) — 1Hybrid Vehicle Control Ecu — 1Inverter With Converter (for Hev Model) — 1Motor Generator Control System (for 2zr-fxe) — 1Plug-in Charge Control System (for Phev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Service Plug Grip (for Hev Model) — 1Sub Radiator — 1Water Pump With Motor — 1Auxiliary Battery — 1Battery Current Sensor — 1Charging System — 1Solar Charging System — 1Solar Control Unit — 1Solar Roof — 1Can Communication System (for Hev Model) — 1Lin Communication System — 1Network Gateway Ecu — 1Integration Control Supply — 1Main Body Ecu — 1Power Integration System — 1Sub Battery System — 1Power Steering Ecu — 1Power Steering System — 1Heated Steering Wheel Controller — 1Heated Steering Wheel System — 1Steering Column Assembly — 1Steering Heater Switch — 1Steering Pad Switch — 1Steering System — 1Steering Wheel — 1Front Lower Ball Joint — 1Front Lower Suspension Arm (for 2zr-fxe Lh Side) — 1Front Lower Suspension Arm (for 2zr-fxe Rh Side) — 1Front Lower Suspension Arm (for M20a-fxs) — 1Front Shock Absorber — 1Front Stabilizer Bar — 1Front Suspension Member — 1Rear Coil Spring — 1Rear Lower Arm (for Awd Lh Side) — 1Rear Lower Arm (for Awd Rh Side) — 1Rear Lower Arm (for Hev Model 2wd) — 1Rear Lower Arm (for Phev Model) — 1Rear Shock Absorber — 1Rear Stabilizer Bar — 1Rear Suspension Member (for 2wd) — 1Rear Suspension Member (for Awd) — 1Rear Trailing Arm — 1Rear Upper Arm — 1Tire And Wheel System — 1Tire Repair Seal — 1Tire Pressure Warning Receiver — 1Tire Pressure Warning System — 1Tire Pressure Warning Valve — 1Acoustic Vehicle Alerting System — 1Vehicle Approaching Speaker — 1Vehicle Approaching Speaker Ecu — 1Back Door — 1Back Door Closer Ecu — 1Back Door Opener Switch — 1Back Door Support — 1Back Door Weatherstrip — 1Charge Lid Courtesy Switch — 1Charge Lid Opener Motor Assembly — 1Charge Lid Opener System — 1Charge Lid Opener Unit — 1Front Door — 1Front Door Opening Trim Weatherstrip — 1Fuel Lid Opener Motor Assembly — 1Fuel Lid Opener Switch — 1Fuel Lid Opener System — 1Hood — 1Hood Lock Control Cable Assembly — 1Power Back Door Closer Switch — 1Power Back Door Control Switch — 1Power Back Door Drive Unit — 1Power Back Door System — 1Power Back Door Touch Sensor — 1Power Back Door Warning Buzzer — 1Rear Door — 1Rear Door Opening Trim Weatherstrip — 1Reserve Lock Switch — 1Front Bumper — 1Front Door Belt Moulding — 1Front Door Window Frame Moulding — 1Front Fender — 1Front Pillar Upper Cover — 1Grille Shutter — 1Grille Shutter System — 1Name Plate — 1Quarter Garnish — 1Rear Bumper — 1Rear Door Belt Moulding — 1Rear Door Window Frame Moulding — 1Rear Wheel House Plate — 1Rocker Panel Moulding — 1Roof Drip Side Finish Moulding — 1Roof Garnish — 1Wheel Opening Moulding (for Front Side) — 1Wheel Opening Moulding (for Rear Side) — 1Windshield Outside Moulding — 1Horn — 1Horn System — 1Relay — 1Automatic Light Control Sensor — 1Back-up Light Assembly — 1Charge Lid Light — 1Front Marker Light — 1Hazard Warning Switch — 1Headlight Assembly — 1Headlight Dimmer Switch — 1Headlight Leveling Switch — 1High Mounted Stop Light Assembly — 1Illumination Light Assembly — 1License Plate Light Assembly — 1Lighting System — 1Rear Combination Light Assembly — 1Rear Light Assembly — 1Rear Side Marker Light Assembly — 1Relay — 1Side Turn Signal Light Assembly — 1Stop Light Switch — 1Switch Housing — 1Outer Mirror Switch — 1Outer Rear View Mirror — 1Outer Rear View Mirror Cover — 1Outer Rear View Mirror Glass — 1Power Mirror Control System — 1Back Door Glass — 1Front Passenger Side Power Window Switch — 1Power Window Control System — 1Power Window Master Switch — 1Power Window Regulator Motor (for Front Door) — 1Power Window Regulator Motor (for Rear Door) — 1Rear Power Window Switch — 1Relay — 1Roof Window Fix Glass — 1Window Defogger System — 1Windshield Deicer Switch — 1Windshield Deicer System — 1Windshield Glass — 1Front Wiper Motor — 1Rain Sensor — 1Relay — 1Washer Motor — 1Washer Nozzle (for Front Side) — 1Washer Nozzle (for Rear Television Camera) — 1Wiper And Washer System — 1Wiper Ecu — 1Wiper Switch — 1Back Door Lock — 1Door Control Receiver — 1Door Control Switch — 1Door Control Transmitter — 1Door Lock Release Motor (for Rear Side) — 1Door Outside Handle (for Rear Side) — 1Front Door Lock — 1Power Door Lock Control System — 1Rear Door Lock — 1Transmitter Battery — 1Wireless Door Lock Control System — 1Accumulator — 1Air Conditioning Amplifier — 1Air Conditioning Panel — 1Air Conditioning Pressure Sensor — 1Air Conditioning Unit — 1Ambient Temperature Sensor — 1Blower Unit — 1Condenser (for Hev Model) — 1Condenser (for Phev Model) — 1Discharge Temperature Sensor — 1Electric Expansion Valve (cooling) — 1Electric Expansion Valve (heating) — 1Evaporator Pipe Temperature Sensor — 1Evaporator Pressure Regulator — 1Front Blower Motor — 1Front Evaporator Front Solenoid Valve — 1Air Conditioning System (for Hev Model) — 1Front Evaporator Temperature Sensor — 1Heat Exchanger Temperature Sensor — 1Heat Pump Ecu — 1High Pressure Magnetic Valve — 1Humidity Sensor — 1Internal Condenser Temperature Sensor — 1Low Pressure Magnetic Valve — 1Refrigerant (for Hfc-134a(r134a)) — 1Refrigerant Line (for Hev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Room Temperature Sensor — 1Solar Sensor — 1Floor Carpet — 1Front Console Box — 1Instrument Panel Safety Pad — 1Roof Headlining — 1Roof Sunshade — 1Ambient Light (for Driver Side) — 1Ambient Light (for Front Passenger Side) — 1Back Door Courtesy Switch — 1Footwell Light — 1Glove Box Light — 1Lighting System — 1Luggage Compartment Room Light — 1Personal Light — 1Room Light — 1Vanity Light — 1Vanity Light Switch — 1Combination Meter — 1Meter / Gauge System — 1Trip Switch — 1Digital Inner Mirror — 1Digital Rear-view Mirror System — 1Inner Mirror Monitor Camera — 1Inner Rear View Mirror (w/o Ec Mirror) — 1Accessory Power Outlet System — 1Power Outlet Socket (for Console Box Front Side) — 1Power Outlet Socket (for Console Box Rear Side) — 1Power Outlet Socket (for Console Box) — 1Power Outlet Socket (for Luggage Compartment) — 1Power Outlet Switch — 1Wireless Charger Assembly — 1Wireless Charging System — 1Climate Control Seat System — 1Front Power Seat Control System (w/ Memory) — 1Front Power Seat Motor Assembly — 1Front Seat Assembly (for Power Seat) — 1Front Seat Cushion Heater (for Power Seat) — 1Front Seatback Heater (for Power Seat) — 1Lumbar Support Adjuster Assembly — 1Power Seat Control Ecu — 1Power Seat Switch — 1Power Seat Track Rail Assembly — 1Rear Seat Assembly — 1Rear Seat Cushion Heater — 1Rear Seat Reminder System — 1Rear Seatback Heater — 1Seat Heater Control — 1Seat Heater Switch (for Front Seat) — 1Seat Heater Switch (for Rear Side) — 1Seat Heater System — 1Seat Memory Switch — 1Child Restraint Seat Anchor Bracket — 1Front Seat Inner Belt Assembly — 1Front Seat Outer Belt Assembly — 1Occupant Detection Sensor (for Front Passenger Side) — 1Rear Center Seat Outer Belt Assembly — 1Rear Seat Inner Belt Assembly (for Rh Side) — 1Rear Seat Outer Belt Assembly — 1Seat Belt Warning System (w/ Occupant Classification System) — 1Tongue Plate Stopper — 1Airbag System — 1Center Airbag Sensor Assembly — 1Curtain Shield Airbag Assembly — 1Front Airbag Sensor — 1Front Passenger Airbag Assembly — 1Front Seat Side Airbag Assembly — 1Inspection After Collision — 1Knee Airbag Assembly — 1Occupant Classification System — 1Rear Seat Side Airbag Assembly — 1Side Airbag Sensor (for Center Pillar) — 1Side Airbag Sensor (for Front Door) — 1Spiral Cable — 1Steering Pad — 1Certification Ecu — 1Digital Key Ecu — 1Digital Key Receiver (for Front Floor) — 1Digital Key Receiver (for Outside Luggage Compartment) — 1Digital Key Receiver (for Rear Door) — 1Digital Key System — 1Electrical Key Oscillator (for Front Floor) — 1Electrical Key Oscillator (for Outside Luggage Compartment) — 1Electrical Key Oscillator (for Rear Floor) — 1Engine Hood Courtesy Switch — 1Id Code Box — 1Smart Key System (for Start Function) — 1
~57min read
4special tools
0102030405054N·mlb·ft
Tightening torque found on this page
  • Precaution
  • Removal
  • Disassembly
  • Inspection
  • Reassembly
  • Installation

Precaution

PRECAUTION

HINT:

  • Any digits beyond the 0.01 mm (1/1000 in.) place for standard, minimum and maximum values should be used as a reference only.
  • When both standard and maximum or minimum values are listed for an inspection, use the standard value as a reference only and base any judgments on the maximum and minimum values.

Removal

REMOVAL

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during engine unit removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

*1: Also necessary after performing a tire rotation.

*2: It is not necessary to perform this procedure if the tire pressure warning valve and transmitters are installed to the same location.

Replacement of ECM

Update ECU security key

Toyota Prius Vehicle Control History (RoB) are stored

ECU configuration

-

Perform Toyota Prius Vehicle Identification Number (VIN) registration

DTC is output

  • Replacement of throttle body assembly
  • Replacement of engine assembly
  • Replacement of cylinder head sub-assembly
  • Replacement of camshaft (for intake or exhaust camshaft)
  • Replacement of camshaft timing gear assembly
  • Replacement of fuel injector assembly
  • Replacement of spark plug
  • Replacement of ignition coil assembly
  • Replacement of EGR valve assembly
  • Gas leak from exhaust system is repaired
  • Replacement of knock control sensor

Inspection after repair

  • Poor idle, etc.
  • Engine start function, etc.

Replacement of inverter with converter assembly

ECU configuration

-

Resolver learning

  • DTCs are stored
  • Slight vibration at a Toyota Prius vehicle speed of 5 km/h or less
  • Shock or vibration during acceleration

Replacement of hybrid vehicle transaxle assembly

  • Resolver learning
  • Initialize resolver
  • DTCs are stored
  • Slight vibration at a Toyota Prius vehicle speed of 5 km/h or less
  • Shock or vibration during acceleration

Suspension parts

Rear television camera assembly optical axis (Back camera position setting)

Parking Assist Monitor System

Parking assist ECU initialization

Panoramic View Monitor System

Advanced Park

Tires

  • Initialization*1*2
  • Tire Position Identification*1*2

Tire Pressure Warning System

Refer to Procedures Necessary When Replacing Parts (for Tire Pressure Warning System) table below

Rear television camera assembly optical axis (Back camera position setting)

Parking Assist Monitor System

Parking assist ECU initialization

Panoramic View Monitor System

Advanced Park

Replacement of front bumper assembly*

Front television camera view adjustment

Panoramic View Monitor System

Advanced Park

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

  • Learning completes when Toyota Prius vehicle is driven

    Effect/Inoperative Function When Necessary Procedures are not Performed

    Necessary Procedures

    Link

    Front Camera System

    Drive the Toyota Prius vehicle straight ahead at 35 km/h or more for 5 seconds or more.

  • Learning completes when vehicle is operated normally

    Effect/Inoperative Function When Necessary Procedures are not Performed

    Necessary Procedures

    Link

    *1: w/o Power Back Door System

    *2: w/ Power Back Door System

    Power Door Lock Control System*1

    • Back door opener

    Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.

    Power Back Door System*2

    Reset back door close position

    Air Conditioning System

    After the ignition switch is turned to ON, the servo motor standard position is recognized.

    -

COMPONENTS (REMOVAL)

Procedure

Part Name Code

1

NO. 8 WATER BY-PASS HOSE

16296

-

-

-

2

WATER OUTLET

16331

-

-

-

3

WATER BY-PASS HOSE

16261

-

-

-

4

NO. 2 WATER BY-PASS HOSE

16264

-

-

-

5

EGR PIPE ASSEMBLY

25610

-

-

-

6

EGR VALVE ASSEMBLY WITH EGR COOLER

25601L

-

-

7

VENTILATION HOSE

12261

-

-

-

8

INTAKE MANIFOLD

17111

-

-

-

9

FUEL DELIVERY PIPE SUB-ASSEMBLY

23807

-

-

10

NO. 1 DELIVERY PIPE SPACER

23807V

-

-

-

11

FUEL INJECTOR ASSEMBLY

23250

-

-

12

PURGE VALVE (PURGE VSV)

17650G

-

-

-

13

FUEL VAPOR FEED PIPE

23818

-

-

-

14

WIRE HARNESS CLAMP BRACKET

-

-

-

-

●

Non-reusable part

-

-

Procedure

Part Name Code

15

NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

17167

-

-

16

MANIFOLD STAY

17118

-

-

17

EXHAUST MANIFOLD (TWC: Front Catalyst)

17141

-

-

18

NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

17168

-

-

-

●

Non-reusable part

-

-

Procedure

Part Name Code

19

ENGINE OIL LEVEL DIPSTICK

15301

-

-

-

20

ENGINE OIL LEVEL DIPSTICK GUIDE

11452

-

-

-

21

WATER BY-PASS PIPE

16268L

-

-

-

22

VENTILATION HOSE

12261

-

-

-

23

IGNITION COIL ASSEMBLY

19500

-

-

●

Non-reusable part

-

-

PROCEDURE

1. REMOVE NO. 8 WATER BY-PASS HOSE

2. REMOVE WATER OUTLET

*1

No. 9 Water By-pass Hose

*2

No. 4 Water By-pass Hose

3. REMOVE WATER BY-PASS HOSE

4. REMOVE NO. 2 WATER BY-PASS HOSE

5. REMOVE EGR PIPE ASSEMBLY

6. REMOVE EGR VALVE ASSEMBLY WITH EGR COOLER

*a

Stud Bolt

-

-

Bolt

Nut

(1) Remove the bolt and 4 nuts.

(2) Using an E8 "TORX" socket wrench, remove the 2 stud bolts and EGR valve assembly with EGR cooler from the cylinder head sub-assembly and exhaust manifold (TWC: Front Catalyst).

(3) Remove the EGR valve assembly with EGR cooler.

(4) Remove the EGR cooler gasket.

7. DISCONNECT VENTILATION HOSE

Click here

8. REMOVE INTAKE MANIFOLD

Click here

9. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

Click here

10. REMOVE NO. 1 DELIVERY PIPE SPACER

Click here

11. REMOVE FUEL INJECTOR ASSEMBLY

Click here

12. REMOVE PURGE VALVE (PURGE VSV)

Click here

13. REMOVE FUEL VAPOR FEED PIPE

14. REMOVE WIRE HARNESS CLAMP BRACKET

15. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Click here

16. REMOVE MANIFOLD STAY

Click here

17. REMOVE EXHAUST MANIFOLD (TWC: Front Catalyst)

Click here

18. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

Click here

19. REMOVE ENGINE OIL LEVEL DIPSTICK

Click here

20. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Click here

21. REMOVE WATER BY-PASS PIPE

22. REMOVE VENTILATION HOSE

23. REMOVE IGNITION COIL ASSEMBLY

Click here

Disassembly

DISASSEMBLY

COMPONENTS (DISASSEMBLY)

Procedure

Part Name Code

1

OIL FILLER CAP SUB-ASSEMBLY

12108

-

-

-

2

SPARK PLUG

19100P

-

-

3

CAMSHAFT POSITION SENSOR

11101E

-

-

4

CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

11101J

-

-

5

CRANKSHAFT POSITION SENSOR

11401G

-

-

6

ENGINE OIL PRESSURE SWITCH ASSEMBLY

83530

-

-

7

KNOCK CONTROL SENSOR

89615

-

-

8

CYLINDER HEAD COVER SUB-ASSEMBLY

11201

-

-

9

CYLINDER HEAD COVER GASKET

11213

-

-

-

10

SPARK PLUG TUBE GASKET

11193

-

-

●

Non-reusable part

★

Precoated part

Procedure

Part Name Code

11

SET NO. 1 CYLINDER TO TDC (COMPRESSION)

-

-

-

12

CRANKSHAFT PULLEY

13471

-

-

13

NO. 1 CHAIN TENSIONER ASSEMBLY

13540

-

-

14

OIL FILTER SUB-ASSEMBLY

15601

-

-

15

OIL FILTER UNION

15600A

-

-

16

WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

16031

-

-

-

17

TIMING CHAIN COVER OIL SEAL

11302A

-

-

18

ENGINE MOUNTING BRACKET RH

12305

-

-

-

19

OIL FILTER BRACKET SUB-ASSEMBLY

15609

-

-

-

20

TIMING CHAIN COVER SUB-ASSEMBLY

11302

-

-

21

ENGINE WATER PUMP ASSEMBLY

16100

-

-

-

22

STUD BOLT

-

-

-

-

23

OIL FILTER BRACKET WITH HEAD STRAIGHT SCREW PLUG GASKET

15609E

-

-

*A

Tyep A

*B

Tyep B

*1

OIL FILTER BRACKET WITH HEAD STRAIGHT SCREW PLUG

-

-

●

Non-reusable part

★

Precoated part

Procedure

Part Name Code

24

CHAIN TENSIONER SLIPPER

13559

-

-

-

25

NO. 1 CHAIN VIBRATION DAMPER

13561

-

-

-

26

NO. 2 CHAIN VIBRATION DAMPER

13562

-

-

-

27

CHAIN SUB-ASSEMBLY

13506

-

-

28

CRANKSHAFT TIMING SPROCKET

13521

-

-

-

29

CHAIN TENSIONER PLATE

13549

-

-

30

NO. 2 CHAIN SUB-ASSEMBLY

13507

-

-

-

31

NO. 1 CRANKSHAFT POSITION SENSOR PLATE

19315

-

-

-

32

CRANKSHAFT TIMING GEAR KEY

13521A

-

-

-

Procedure

Part Name Code

33

INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

13050

-

-

34

CAMSHAFT TIMING GEAR ASSEMBLY

13050

-

-

35

CAMSHAFT TIMING SPROCKET

-

-

-

36

CAMSHAFT BEARING CAP

-

-

-

37

CAMSHAFT

13511

-

-

-

38

NO. 2 CAMSHAFT

13512

-

-

-

39

NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

13801

-

-

-

40

VALVE LASH ADJUSTER ASSEMBLY

13750

-

-

-

41

VALVE STEM CAP

13716

-

-

-

42

OIL CONTROL VALVE FILTER

15678A

-

-

-

43

NO. 1 CAMSHAFT BEARING

-

-

-

-

44

NO. 2 CAMSHAFT BEARING

-

-

-

-

45

CAMSHAFT HOUSING SUB-ASSEMBLY

11103

-

-

●

Non-reusable part

-

-

Procedure

Part Name Code

46

CYLINDER HEAD SUB-ASSEMBLY

11101

-

-

47

CYLINDER HEAD GASKET

11115

-

-

-

48

CYLINDER BLOCK WATER JACKET SPACER

11445

-

-

-

●

Non-reusable part

-

-

Procedure

Part Name Code

49

PCV VALVE (VENTILATION VALVE SUB-ASSEMBLY)

12204

-

-

50

OIL PAN DRAIN PLUG

12101A

-

-

-

51

NO. 2 OIL PAN SUB-ASSEMBLY

12102A

-

-

52

ENGINE OIL LEVEL SENSOR

89491

-

-

-

53

OIL PUMP ASSEMBLY

15100

-

-

-

54

STIFFENING CRANKCASE ASSEMBLY

11420

-

-

55

REAR ENGINE OIL SEAL

11401L

-

-

56

NO. 1 TAPER SCREW PLUG

11432A

-

-

-

57

STUD BOLT

-

-

-

58

RING PIN

-

-

-

●

Non-reusable part

★

Precoated part

PROCEDURE

1. REMOVE OIL FILLER CAP SUB-ASSEMBLY

2. REMOVE SPARK PLUG

Click here

3. REMOVE CAMSHAFT POSITION SENSOR

Click here

4. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

Click here

5. REMOVE CRANKSHAFT POSITION SENSOR

Click here

6. REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY

Click here

7. REMOVE KNOCK CONTROL SENSOR

Click here

8. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

(1) Remove the 16 bolts and cylinder head cover sub-assembly from the camshaft housing sub-assembly.

(2) Remove the 2 gaskets from the camshaft bearing cap.

NOTICE:

As the gaskets may stick to the cylinder head cover sub-assembly, be careful not to drop any of the gaskets into the engine when removing the cylinder head cover sub-assembly.

9. REMOVE CYLINDER HEAD COVER GASKET

10. REMOVE SPARK PLUG TUBE GASKET

(1) Using a screwdriver as shown in the illustration, deform each spark plug tube gasket inwards and remove the 4 spark plug tube gaskets from the cylinder head cover sub-assembly.

11. SET NO. 1 CYLINDER TO TDC (COMPRESSION)

*a

Timing Mark

*b

Timing Notch

*c

Timing Mark (Rectangle)

*d

Mark (Circle)

(1) Turn the crankshaft pulley until its timing notch is aligned with timing mark "0" of the timing chain cover sub-assembly.

HINT:

There are 3 marks on the camshaft timing sprocket. Make sure that the timing mark (rectangle) is at the top.

(2) Check that the timing marks on both the camshaft timing sprocket and camshaft timing gear assembly are facing upward as shown in the illustration.

HINT:

If not, turn the crankshaft 1 complete revolution (360°) and align the timing marks as shown in the illustration.

12. REMOVE CRANKSHAFT PULLEY

Click here

13. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

NOTICE:

Do not turn the crankshaft without the No. 1 chain tensioner assembly installed.

14. REMOVE OIL FILTER SUB-ASSEMBLY

Click here

15. REMOVE OIL FILTER UNION

(1) Using a 12 mm hexagon socket wrench, remove the oil filter union from the oil filter bracket sub-assembly.

16. REMOVE WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

Click here

17. REMOVE TIMING CHAIN COVER OIL SEAL

Click here

18. REMOVE ENGINE MOUNTING BRACKET RH

19. REMOVE OIL FILTER BRACKET SUB-ASSEMBLY

20. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

*1

Seal Washer

-

-

(1) Remove the 18 bolts and seal washer from the timing chain cover sub-assembly.

(2) Remove the timing chain cover sub-assembly by prying between the timing chain cover sub-assembly and cylinder head sub-assembly, camshaft housing sub-assembly, cylinder block sub-assembly and stiffening crankcase assembly with a screwdriver with its tip wrapped with protective tape.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder head sub-assembly, camshaft housing sub-assembly, cylinder block sub-assembly, stiffening crankcase assembly and timing chain cover sub-assembly.

(3) Remove the 3 O-rings from the cylinder head sub-assembly and cylinder block sub-assembly.

21. REMOVE ENGINE WATER PUMP ASSEMBLY

22. REMOVE STUD BOLT

23. REMOVE OIL FILTER BRACKET WITH HEAD STRAIGHT SCREW PLUG GASKET

(1) Using a 10 mm hexagon socket wrench, remove the 2 oil filter bracket with head straight screw plugs and 2 oil filter bracket with head straight screw plug gaskets from the oil filter bracket.

24. REMOVE CHAIN TENSIONER SLIPPER

25. REMOVE NO. 1 CHAIN VIBRATION DAMPER

26. REMOVE NO. 2 CHAIN VIBRATION DAMPER

27. REMOVE CHAIN SUB-ASSEMBLY

Click here

28. REMOVE CRANKSHAFT TIMING SPROCKET

29. REMOVE CHAIN TENSIONER PLATE

*1

Chain Tensioner Plate

*2

Chain Damper Spring

(1) Temporarily install the crankshaft pulley with the crankshaft pulley set bolt.

(2) Using SST, hold the crankshaft pulley. Then remove the oil pump drive shaft gear nut.

SST: 09213-58014

91551-80840

SST: 09330-00021

(3) Remove SST, the crankshaft pulley set bolt and crankshaft pulley.

(4) Remove the bolt, chain tensioner plate and chain damper spring.

30. REMOVE NO. 2 CHAIN SUB-ASSEMBLY

*1

No. 2 Chain Sub-assembly

*2

Oil Pump Drive Gear

*3

Oil Pump Drive Shaft Gear

-

-

31. REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

32. REMOVE CRANKSHAFT TIMING GEAR KEY

(1) Using a screwdriver with its tip wrapped with protective tape, remove the 2 crankshaft timing gear keys from the crankshaft.

33. INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

*a

Adhesive Tape Sealing Area

*b

Prick a hole

Lock

-

-

(1) Check the lock of the camshaft timing gear assembly.

(2) After cleaning the oil hole in the intake side of the No. 1 camshaft bearing cap, completely seal the oil hole with adhesive tape or equivalent as shown in the illustration to prevent air from leaking.

NOTICE:

Be sure to cover the oil hole completely because air leaks due to insufficient sealing will prevent the lock pin from being released.

(3) Prick a hole in the tape covering the oil hole as shown in the illustration. (Procedure A)

(4) Apply approximately 150 kPa (1.5 kgf/cm2, 22 psi) of air pressure to the hole pricked in procedure A to release the lock pin.

NOTICE:

  • If air leaks out, reattach the adhesive tape.
  • Cover the oil hole with a piece of cloth when applying air pressure to prevent oil from spraying.

(5) Forcibly turn the camshaft timing gear assembly in the advance direction (counterclockwise).

HINT:

Depending on the air pressure applied, the camshaft timing gear assembly may turn in the advance direction without assistance.

(6) Turn the camshaft timing gear assembly within its movable range (30 to 32°) 2 or 3 times without turning it to the most retarded position. Make sure that the camshaft timing gear assembly turns smoothly.

NOTICE:

  • Do not lock the camshaft timing gear assembly.
  • If camshaft timing gear assembly is locked, release the lock pin again.

(7) Remove the adhesive tape from the No. 1 camshaft bearing cap.

34. REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

(1) Using a wrench to hold the hexagonal portion of the camshaft, remove the bolt and camshaft timing gear assembly.

NOTICE:

  • Before removing the camshaft timing gear assembly, make sure that the lock pin has been released.
  • Be sure not to remove the other 4 bolts.
  • Keep the camshaft timing gear assembly horizontal while removing it from the camshaft.

*a

Do not remove

35. REMOVE CAMSHAFT TIMING SPROCKET

(1) Using a wrench to hold the hexagonal portion of the No. 2 camshaft, remove the bolt and camshaft timing sprocket.

36. REMOVE CAMSHAFT BEARING CAP

(1) Uniformly loosen and remove the 10 bolts in the order shown in the illustration.

(2) Uniformly loosen and remove the 15 bolts in the order shown in the illustration.

NOTICE:

Make sure that the camshaft and No. 2 camshaft remain level while uniformly loosening the bolts.

(3) Remove the 5 camshaft bearing caps.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.

37. REMOVE CAMSHAFT

38. REMOVE NO. 2 CAMSHAFT

Click here

39. REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

40. REMOVE VALVE LASH ADJUSTER ASSEMBLY

41. REMOVE VALVE STEM CAP

42. REMOVE OIL CONTROL VALVE FILTER

43. REMOVE NO. 1 CAMSHAFT BEARING

44. REMOVE NO. 2 CAMSHAFT BEARING

45. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY

(1) Remove the 2 bolts from the camshaft housing sub-assembly.

(2) Remove the camshaft housing sub-assembly by prying between the cylinder head sub-assembly and camshaft housing sub-assembly with a screwdriver with its tip wrapped with protective tape.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder head sub-assembly and camshaft housing sub-assembly.

46. REMOVE CYLINDER HEAD SUB-ASSEMBLY

(1) Using a 10 mm bi-hexagon socket wrench, uniformly loosen and remove the 10 cylinder head set bolts and 10 cylinder head set plate washers in several steps in the order shown in the illustration.

NOTICE:

  • Do not drop the cylinder head set plate washers into the cylinder head sub-assembly.
  • Removing the cylinder head set bolts in the incorrect order may cause warpage or cracking of the cylinder head sub-assembly.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.

(2) Remove the cylinder head sub-assembly from the cylinder block sub-assembly.

47. REMOVE CYLINDER HEAD GASKET

Click here

48. REMOVE CYLINDER BLOCK WATER JACKET SPACER

49. REMOVE PCV VALVE (VENTILATION VALVE SUB-ASSEMBLY)

Click here

50. REMOVE OIL PAN DRAIN PLUG

51. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

*a

Nut

-

-

(1) Remove the 10 bolts and 2 nuts from the No. 2 oil pan sub-assembly.

(2) Insert the blade of an oil pan seal cutter between the stiffening crankcase assembly and No. 2 oil pan sub-assembly. Cut through the applied sealer and remove the No. 2 oil pan sub-assembly.

NOTICE:

  • Be careful not to damage the surface of the No. 2 oil pan sub-assembly which contacts the stiffening crankcase assembly.
  • Be careful not to damage the flange of the stiffening crankcase assembly.

52. REMOVE ENGINE OIL LEVEL SENSOR

Click here

53. REMOVE OIL PUMP ASSEMBLY

Click here

54. REMOVE STIFFENING CRANKCASE ASSEMBLY

(1) Uniformly loosen and remove the 11 bolts from the stiffening crankcase assembly.

(2) Remove the stiffening crankcase assembly by prying between the stiffening crankcase assembly and cylinder block sub-assembly with a screwdriver with its tip wrapped with protective tape.

NOTICE:

Be careful not to damage the contact surfaces of the stiffening crankcase assembly and cylinder block sub-assembly.

55. REMOVE REAR ENGINE OIL SEAL

NOTICE:

Be careful not to damage the crankshaft.

56. REMOVE NO. 1 TAPER SCREW PLUG

57. REMOVE STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.

58. REMOVE RING PIN

NOTICE:

It is not necessary to remove ring pins unless they are being replaced.

Inspection

INSPECTION

PROCEDURE

1. INSPECT NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

(a) Turn the roller by hand to check that it turns smoothly.

(b) If the roller does not turn smoothly, replace the No. 1 valve rocker arm sub-assembly.

2. INSPECT VALVE LASH ADJUSTER ASSEMBLY

NOTICE:

  • Keep the valve lash adjuster assembly free from dirt and foreign matter.
  • Only use clean engine oil.

Pre-procedure1

(a) Place the valve lash adjuster assembly into a container filled with engine oil.

(b) Insert the tip of SST into the valve lash adjuster assembly plunger and use the tip to press down on the check ball inside the plunger.

*a

Correct

*b

Incorrect

*c

Taper

*d

Low Pressure Chamber

*e

High Pressure Chamber

*f

Plunger

*g

Check Ball

-

-

SST: 09276-75010

(c) Squeeze SST and the valve lash adjuster assembly together to move the plunger up and down 5 to 6 times.

Procedure1

(d) Check the movement of the plunger and bleed the air.

OK:

Plunger moves up and down.

NOTICE:

When bleeding air from the high-pressure chamber, make sure that the tip of SST is actually pressing the check ball as shown in the illustration. If the check ball is not pressed, air will not bleed.

Procedure2

(e) After bleeding the air, remove SST. Then try to quickly and firmly press the plunger by hand.

OK:

Plunger is very difficult to move.

(f) If the plunger is easy to move, replace the valve lash adjuster assembly.

Post-procedure1

(g) None

3. INSPECT CHAIN SUB-ASSEMBLY

Pre-procedure1

(a) Using a spring scale, pull the chain sub-assembly with a force of 147 N (15 kgf, 33.0 lbf) as shown in the illustration.

*a

Measurement Length

Procedure1

(b) Using a vernier caliper, measure the length of 15 links.

Maximum Chain Elongation:

Specified Condition

Result

115.2 mm

4.54 in.

mm

in.

NOTICE:

Perform the measurement at 3 random places. Use the average of the measurements.

(c) If the average elongation is more than the maximum, replace the chain sub-assembly.

Post-procedure1

(d) None

4. INSPECT NO. 2 CHAIN SUB-ASSEMBLY

Pre-procedure1

(a) Using a spring scale, pull the No. 2 chain sub-assembly with a force of 147 N (15 kgf, 33.0 lbf) as shown in the illustration.

*a

Measurement Length

Procedure1

(b) Using a vernier caliper, measure the length of 15 links.

Maximum Chain Elongation:

Specified Condition

Result

102.1 mm

4.02 in.

mm

in.

NOTICE:

Perform the measurement at 3 random places. Use the average of the measurements.

(c) If the average elongation is more than the maximum, replace the No. 2 chain sub-assembly.

Post-procedure1

(d) None

5. INSPECT OIL PUMP DRIVE GEAR

Pre-procedure1

(a) Place the No. 2 chain sub-assembly around the oil pump drive gear.

Procedure1

(b) Using a vernier caliper, measure the diameter of the oil pump drive gear and No. 2 chain sub-assembly.

Minimum Gear Diameter (with No. 2 Chain Sub-assembly):

Specified Condition

Result

48.2 mm

1.90 in.

mm

in.

NOTICE:

The vernier caliper must be in contact with the chain rollers when measuring.

(c) If the diameter is less than the minimum, replace the No. 2 chain sub-assembly and oil pump drive gear.

Post-procedure1

(d) None

6. INSPECT OIL PUMP DRIVE SHAFT GEAR

Pre-procedure1

(a) Place the No. 2 chain sub-assembly around the oil pump drive shaft gear.

Procedure1

(b) Using a vernier caliper, measure the diameter of the oil pump drive shaft gear and No. 2 chain sub-assembly.

Minimum Gear Diameter (with No. 2 Chain Sub-assembly):

Specified Condition

Result

48.2 mm

1.90 in.

mm

in.

NOTICE:

The vernier caliper must be in contact with the chain rollers when measuring.

(c) If the diameter is less than the minimum, replace the No. 2 chain sub-assembly and oil pump drive shaft gear.

Post-procedure1

(d) None

7. INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

Pre-procedure1

(a) Place the chain sub-assembly around the camshaft timing gear assembly.

Procedure1

(b) Using a vernier caliper, measure the diameter of the camshaft timing gear assembly and chain sub-assembly.

Minimum Gear Diameter (with Chain Sub-assembly):

Specified Condition

Result

96.8 mm

3.81 in.

mm

in.

NOTICE:

The vernier caliper must be in contact with the chain rollers when measuring.

(c) If the diameter is less than the minimum, replace the chain sub-assembly and camshaft timing gear assembly.

Post-procedure1

(d) None

8. INSPECT CAMSHAFT TIMING SPROCKET

Pre-procedure1

(a) Place the chain sub-assembly around the camshaft timing sprocket.

Procedure1

(b) Using a vernier caliper, measure the diameter of the camshaft timing sprocket and chain sub-assembly.

Minimum Gear Diameter (with Chain Sub-assembly):

Specified Condition

Result

96.8 mm

3.81 in.

mm

in.

NOTICE:

The vernier caliper must be in contact with the chain rollers when measuring.

(c) If the diameter is less than the minimum, replace the chain sub-assembly and camshaft timing sprocket.

Post-procedure1

(d) None

9. INSPECT CRANKSHAFT TIMING GEAR OR SPROCKET

Pre-procedure1

(a) Place the chain sub-assembly around the crankshaft timing sprocket.

Procedure1

(b) Using a vernier caliper, measure the diameter of the crankshaft timing sprocket and chain sub-assembly.

Minimum Sprocket Diameter (with Chain Sub-assembly):

Specified Condition

Result

51.1 mm

2.01 in.

mm

in.

NOTICE:

The vernier caliper must be in contact with the chain rollers when measuring.

(c) If the diameter is less than the minimum, replace the chain sub-assembly and crankshaft timing sprocket.

Post-procedure1

(d) None

10. INSPECT CHAIN TENSIONER SLIPPER

(a) Using a vernier caliper, measure the wear depth of the chain tensioner slipper.

Maximum Depth:

Specified Condition

Result

1.0 mm

0.0394 in.

mm

in.

*a

Depth

(b) If the depth is more than the maximum, replace the chain tensioner slipper.

11. INSPECT NO. 1 CHAIN VIBRATION DAMPER

(a) Using a vernier caliper, measure the wear depth of the No. 1 chain vibration damper.

Maximum Depth:

Specified Condition

Result

1.0 mm

0.0394 in.

mm

in.

*a

Depth

(b) If the depth is more than the maximum, replace the No. 1 chain vibration damper.

12. INSPECT NO. 2 CHAIN VIBRATION DAMPER

(a) Using a vernier caliper, measure the wear depth of the No. 2 chain vibration damper.

Maximum Depth:

Specified Condition

Result

1.0 mm

0.0394 in.

mm

in.

*a

Depth

(b) If the depth is more than the maximum, replace the No. 2 chain vibration damper.

13. INSPECT CHAIN TENSIONER PLATE

(a) Using a vernier caliper, measure the wear depth of the chain tensioner plate.

Maximum Depth:

Specified Condition

Result

1.0 mm

0.0394 in.

mm

in.

*a

Depth

(b) If the depth is more than the maximum, replace the chain tensioner plate.

14. INSPECT NO. 1 CHAIN TENSIONER ASSEMBLY

(a) Check that the plunger moves smoothly when the cam is raised with your finger.

*a

Raise

*b

Move

*c

Lock

(b) Release the cam, then check that the plunger is locked in place by the cam and does not move when pushed with your finger.

(c) If the plunger does not move smoothly, replace the No. 1 chain tensioner assembly.

15. INSPECT CAMSHAFT

(a) Inspect the camshaft for runout.

(1) Place the camshaft on V-blocks.

(2) Using a dial indicator, measure the runout at the center journal.

Maximum Runout:

Specified Condition

Result

0.03 mm

0.00118 in.

mm

in.

(3) If the runout is more than the maximum, replace the camshaft.

(b) Inspect the cam lobes.

(1) Using a micrometer, measure the cam lobe height.

Standard Cam Lobe Height:

Minimum Cam Lobe Height

Specified Condition

Result

42.766 mm

1.6837 in.

42.816 to 42.916 mm

1.6857 to 1.6896 in.

mm

in.

(2) If the cam lobe height is less than the minimum, replace the camshaft.

(c) Inspect the camshaft journals.

(1) Using a micrometer, measure the journal diameter.

Standard Journal Diameter:

Item

Specified Condition

Result

No. 1 journal

34.449 to 34.465 mm

1.3563 to 1.3569 in.

mm

in.

Other journals

22.949 to 22.965 mm

0.90350 to 0.90413 in.

mm

in.

(2) If the journal diameter is not as specified, check the camshaft oil clearance.

Click here

16. INSPECT NO. 2 CAMSHAFT

(a) Inspect the No. 2 camshaft for runout.

(1) Place the No. 2 camshaft on V-blocks.

(2) Using a dial indicator, measure the runout at the center journal.

Maximum Runout:

Specified Condition

Result

0.03 mm

0.00118 in.

mm

in.

(3) If the runout is more than the maximum, replace the No. 2 camshaft.

(b) Inspect the cam lobes.

(1) Using a micrometer, measure the cam lobe height.

Standard Cam Lobe Height:

Minimum Cam Lobe Height

Specified Condition

Result

43.294 mm

1.7045 in.

43.344 to 43.444 mm

1.7065 to 1.7104 in.

mm

in.

(2) If the cam lobe height is less than the minimum, replace the No. 2 camshaft.

(c) Inspect the No. 2 camshaft journals.

(1) Using a micrometer, measure the journal diameter.

Standard Journal Diameter:

Item

Specified Condition

Result

No. 1 journal

34.449 to 34.465 mm

1.3563 to 1.3569 in.

mm

in.

Other journals

22.949 to 22.965 mm

0.90350 to 0.90413 in.

mm

in.

(2) If the journal diameter is not as specified, check the No. 2 camshaft oil clearance.

HINT:

Click here

17. INSPECT CYLINDER HEAD SET BOLT

(a) Using a vernier caliper, measure the length of the cylinder head set bolt from the seat to the end.

Standard Length:

Maximum Length

Specified Condition

Result

149.2 mm

5.87 in.

146.8 to 148.2 mm

5.78 to 5.83 in.

mm

in.

(1) If the length is greater than the maximum, replace the cylinder head set bolt with a new one. Failure to do so may lead to engine damage.

(2) If there is any thread deformation, replace the cylinder head set bolt with a new one.

*a

Measurement Length

*b

Measurement Area

*c

115 mm (4.53 in.)

(b) Using a vernier caliper, measure the diameter of the threads at several points within the area shown in the illustration.

Standard Diameter:

Measurement Point (Distance from the Seat)

Minimum Diameter

Specified Condition

Result

115 mm

4.53 in.

9.4 mm

0.370 in.

9.77 to 9.96 mm

0.385 to 0.392 in.

mm

in.

NOTICE:

Diameter measurements should be done at several points.

(1) If the diameter is less than the minimum, replace the cylinder head set bolt with a new one. Failure to do so may lead to engine damage.

(2) If there is any thread deformation, replace the cylinder head set bolt with a new one.

18. INSPECT CAMSHAFT THRUST CLEARANCE

Pre-procedure1

(a) Clean the camshaft, No. 2 camshaft and camshaft bearing caps.

(b) Place the camshaft, No. 2 camshaft and camshaft housing sub-assembly on the cylinder head sub-assembly.

(c) Install the camshaft bearing caps.

HINT:

Click here

(d) Install the camshaft housing sub-assembly.

HINT:

Click here

Procedure1

(e) Using a dial indicator, measure the thrust clearance while moving the camshaft and No. 2 camshaft back and forth.

Standard Thrust Clearance:

Maximum Thrust Clearance

Specified Condition

Result

0.17 mm

0.00669 in.

0.06 to 0.155 mm

0.00236 to 0.00610 in.

mm

in.

(f) If the thrust clearance is more than the maximum, replace the camshaft housing sub-assembly. If the thrust surface is damaged, replace the camshaft.

Post-procedure1

(g) None

19. INSPECT CAMSHAFT OIL CLEARANCE

Pre-procedure1

(a) Clean the camshaft bearing caps and camshaft journals.

(b) Place the camshaft, No. 2 camshaft and camshaft housing sub-assembly on the cylinder head sub-assembly.

(c) Lay a strip of Plastigage across each of the camshaft journals.

*a

Plastigage

(d) Install the camshaft bearing caps.

NOTICE:

Do not turn the camshaft.

HINT:

Click here

(e) Remove the camshaft bearing caps.

HINT:

Click here

Procedure1

(f) Measure the Plastigage at its widest point.

Standard Oil Clearance:

Item

Maximum Oil Clearance

Specified Condition

Result

No. 1 Journal

0.085 mm

0.00335 in.

0.030 to 0.063 mm

0.00118 to 0.00248 in.

mm

in.

Other Journals

0.09 mm

0.00354 in.

0.035 to 0.072 mm

0.00138 to 0.00283 in.

mm

in.

NOTICE:

Completely remove the Plastigage after the inspection.

*a

Plastigage

(g) If the oil clearance is greater than the maximum, replace the camshaft or No. 2 camshaft. If necessary, replace the cylinder head sub-assembly.

Post-procedure1

(h) None

20. INSPECT EXHAUST MANIFOLD (TWC: Front Catalyst)

(a) Using a precision straightedge and feeler gauge, check the surface that contacts the cylinder head sub-assembly for warpage.

Maximum Warpage:

Specified Condition

Result

0.7 mm

0.0276 in.

mm

in.

(b) If the warpage is more than the maximum, replace the exhaust manifold (TWC: Front Catalyst).

Reassembly

REASSEMBLY

COMPONENTS (REASSEMBLY)

Procedure

Part Name Code

1

RING PIN

-

-

-

2

STUD BOLT

-

-

-

3

NO. 1 TAPER SCREW PLUG

11432A

-

-

4

STIFFENING CRANKCASE ASSEMBLY

11420

-

-

5

OIL PUMP ASSEMBLY

15100

-

-

-

6

ENGINE OIL LEVEL SENSOR

89491

-

-

-

7

NO. 2 OIL PAN SUB-ASSEMBLY

12102A

-

-

8

OIL PAN DRAIN PLUG

12101A

-

-

-

9

REAR ENGINE OIL SEAL

11401L

-

-

10

PCV VALVE (VENTILATION VALVE SUB-ASSEMBLY)

12204

-

-

N*m (kgf*cm, ft.*lbf): Specified torque

●

Non-reusable part

MP grease

Adhesive 1324

★

Procoated part

-

-

Procedure

Part Name Code

11

CYLINDER BLOCK WATER JACKET SPACER

11445

-

-

12

CYLINDER HEAD GASKET

11115

-

-

13

CYLINDER HEAD SUB-ASSEMBLY

11101

-

-

Tightening torque for "Major areas involving basic Toyota Prius vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf)

●

Non-reusable part

*T1

1st: 49 (500, 36)

2nd: Turn 90°

3rd: Turn 45°

-

-

Procedure

Part Name Code

14

VALVE STEM CAP

13716

-

-

15

VALVE LASH ADJUSTER ASSEMBLY

13750

-

-

16

NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

13801

-

-

17

RING PIN

-

-

-

18

NO. 1 CAMSHAFT BEARING

-

-

-

19

NO. 2 CAMSHAFT BEARING

-

-

-

20

OIL CONTROL VALVE FILTER

15678A

-

-

21

NO. 2 CAMSHAFT

13512

-

-

22

CAMSHAFT

13511

-

-

23

CAMSHAFT BEARING CAP

-

-

-

24

CAMSHAFT HOUSING SUB-ASSEMBLY

11103

-

-

25

CAMSHAFT TIMING SPROCKET

-

-

-

26

CAMSHAFT TIMING GEAR ASSEMBLY

13050

-

-

N*m (kgf*cm, ft.*lbf): Specified torque

●

Non-reusable part

Procedure

Part Name Code

27

CRANKSHAFT TIMING GEAR KEY

13521A

-

-

28

NO. 1 CRANKSHAFT POSITION SENSOR PLATE

19315

-

-

29

NO. 2 CHAIN SUB-ASSEMBLY

13507

-

-

30

CHAIN TENSIONER PLATE

13549

-

-

31

CRANKSHAFT TIMING SPROCKET

13521

-

-

-

32

SET NO. 1 CYLINDER TO TDC (COMPRESSION)

-

-

-

33

NO. 1 CHAIN VIBRATION DAMPER

13561

-

-

-

34

CHAIN SUB-ASSEMBLY

13506

-

-

35

NO. 2 CHAIN VIBRATION DAMPER

13562

-

-

-

36

CHAIN TENSIONER SLIPPER

13559

-

-

-

N*m (kgf*cm, ft.*lbf): Specified torque

-

-

Procedure

Part Name Code

37

OIL FILTER BRACKET WITH HEAD STRAIGHT SCREW PLUG GASKET

15609E

-

-

38

STUD BOLT

-

-

-

39

ENGINE WATER PUMP ASSEMBLY

16100

-

-

40

TEMPORARILY TIGHTEN TIMING CHAIN COVER SUB-ASSEMBLY

11302

-

-

41

ENGINE MOUNTING BRACKET RH

12305

-

-

42

OIL FILTER BRACKET SUB-ASSEMBLY

15609

-

-

43

TIGHTEN TIMING CHAIN COVER SUB-ASSEMBLY

11302

-

-

44

TIMING CHAIN COVER OIL SEAL

11302A

-

-

45

WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

16031

-

-

-

46

CRANKSHAFT PULLEY

13471

-

-

47

NO. 1 CHAIN TENSIONER ASSEMBLY

13540

-

-

48

OIL FILTER UNION

15600A

-

-

49

OIL FILTER SUB-ASSEMBLY

15601

-

-

*A

Tyep A

*B

Tyep B

*1

OIL FILTER BRACKET WITH HEAD STRAIGHT SCREW PLUG

-

-

Tightening torque for "Major areas involving basic Toyota Prius vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf)

N*m (kgf*cm, ft.*lbf): Specified torque

●

Non-reusable part

MP grease

Adhesive 1324

★

Precoated part

Do not apply lubricants to the threaded parts

-

-

Procedure

Part Name Code

50

SPARK PLUG TUBE GASKET

11193

-

-

-

51

CYLINDER HEAD COVER GASKET

11213

-

-

52

ENGINE OIL PRESSURE SWITCH ASSEMBLY

83530

-

-

53

KNOCK CONTROL SENSOR

89615

-

-

54

CRANKSHAFT POSITION SENSOR

11401G

-

-

55

CYLINDER HEAD COVER SUB-ASSEMBLY

11201

-

-

56

CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

11101J

-

-

57

CAMSHAFT POSITION SENSOR

11101E

-

-

58

SPARK PLUG

19100P

-

-

59

OIL FILLER CAP SUB-ASSEMBLY

12108

-

-

-

N*m (kgf*cm, ft.*lbf): Specified torque

●

Non-reusable part

Adhesive 1344

★

Procoated part

PROCEDURE

1. INSTALL RING PIN

NOTICE:

It is not necessary to remove ring pins unless they are being replaced.

*a

Protrusion Height

*b

11 mm (0.433 in.)

*c

8.0 mm (0.315 in.)

-

-

(1) Using a plastic hammer, tap 2 new ring pins into the stiffening crankcase assembly.

Standard Ring Pin:

Item

Protrusion Height

Height

Width

Ring pin

4.0 mm (0.157 in.)

8.0 mm (0.315 in.)

11 mm (0.433 in.)

(2) Using a plastic hammer, tap 2 new ring pins into the stiffening crankcase assembly.

Standard Ring Pin:

Item

Protrusion Height

Height

Width

Ring pin

3.0 mm (0.118 in.)

8.0 mm (0.315 in.)

11 mm (0.433 in.)

2. INSTALL STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.

*a

9 mm (0.354 in.)

*b

19 mm (0.748 in.)

(1) Using an E6 "TORX" socket wrench, install the 2 stud bolts as shown in the illustration.

Torque:

5 N·m {51 kgf·cm, 44 in·lbf}

3. INSTALL NO. 1 TAPER SCREW PLUG

(1) Apply adhesive to 2 or 3 threads of the No. 1 taper screw plug.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

NOTICE:

  • Install the No. 1 taper screw plug within 3 minutes of applying adhesive.
  • Do not start the engine for at least 1 hour after installing the No. 1 taper screw plug.

(2) Install the No. 1 taper screw plug.

Torque:

43 N·m {438 kgf·cm, 32 ft·lbf}

4. INSTALL STIFFENING CRANKCASE ASSEMBLY

(1) Apply seal packing as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

Standard Seal Packing Diameter:

Area

Specified Condition

Continuous Line

2.0 to 3.0 mm (0.0787 to 0.118 in.)

(A)

4.5 to 5.5 mm (0.177 to 0.217 in.)

Application Length (A):

56 mm (2.20 in.)

NOTICE:

  • Remove any oil from the contact surfaces.
  • Install the stiffening crankcase assembly within 3 minutes and tighten the bolts within 15 minutes of applying seal packing.
  • Do not start the engine for at least 2 hours after installing the stiffening crankcase assembly.

(2) Temporarily install the stiffening crankcase assembly with the 11 bolts.

Bolt Length:

Item

Specified Condition

Bolt (A)

138 mm (5.43 in.)

Bolt (B)

35 mm (1.38 in.)

Bolt (C)

70 mm (2.76 in.)

(3) Tighten the 11 bolts in the order shown in the illustration to install the stiffening crankcase assembly.

Torque:

21 N·m {214 kgf·cm, 15 ft·lbf}

5. INSTALL OIL PUMP ASSEMBLY

Click here

6. INSTALL ENGINE OIL LEVEL SENSOR

Click here

7. INSTALL NO. 2 OIL PAN SUB-ASSEMBLY

*a

Seal Packing

*b

6.0 mm

*c

3.0 to 4.5 mm

*d

Nut

(1) Remove any remaining seal packing.

NOTICE:

  • Remove any oil from the contact surfaces.
  • Install the No. 2 oil pan sub-assembly within 3 minutes and tighten the bolts within 10 minutes of applying seal packing.
  • Do not add engine oil for at least 2 hours after installing the No. 2 oil pan sub-assembly.
  • Keep the contact surfaces of the stiffening crankcase assembly and No. 2 oil pan sub-assembly free of oil.

(2) Apply seal packing in a continuous line as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three bond 1207B or equivalent

Application Specification:

Area

Seal Packing Diameter

Distance from Center of Bolt Hole to Center of Seal Packing

(A) - (A)

3.0 to 4.5 mm (0.118 to 0.177 in.)

6.0 mm (0.236 in.)

(B) - (B)

-

(3) Install the No. 2 oil pan sub-assembly to the stiffening crankcase assembly with the 10 bolts and 2 nuts.

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

8. INSTALL OIL PAN DRAIN PLUG

Torque:

37 N·m {377 kgf·cm, 27 ft·lbf}

9. INSTALL REAR ENGINE OIL SEAL

Click here

10. INSTALL PCV VALVE (VENTILATION VALVE SUB-ASSEMBLY)

Click here

11. INSTALL CYLINDER BLOCK WATER JACKET SPACER

NOTICE:

Make sure that the cylinder block water jacket spacer does not stick out from the top surface of the cylinder block sub-assembly.

Front of Engine

-

-

(1) Install the 2 cylinder block water jacket spacers to the cylinder block sub-assembly as shown in the illustration.

12. INSTALL CYLINDER HEAD GASKET

Click here

13. INSTALL CYLINDER HEAD SUB-ASSEMBLY

HINT:

The cylinder head set bolts are tightened in 3 progressive steps.

(1) Clean the cylinder block sub-assembly and cylinder head sub-assembly with solvent.

(2) Place the cylinder head sub-assembly on the cylinder block sub-assembly.

NOTICE:

  • Remove any oil from the contact surface of the cylinder head sub-assembly.
  • Place the cylinder head sub-assembly on the cylinder block sub-assembly gently in order not to damage the cylinder head gasket with the bottom of the cylinder head sub-assembly.

(3) Install the 10 cylinder head set plate washers to the 10 cylinder head set bolts.

(4) Apply a light coat of engine oil to the threads and under the heads of the cylinder head set bolts.

*a

Paint Mark

*b

Before Wiping off

*c

After Wiping off

-

-

Front of Engine

-

-

(1) Step 1:

1. Using a 10 mm bi-hexagon socket wrench, install and uniformly tighten the 10 cylinder head set bolts in several steps in the order shown in the illustration.

Torque:

49 N·m {500 kgf·cm, 36 ft·lbf}

NOTICE:

Do not drop the cylinder head set plate washers for the cylinder head set bolts into the cylinder head sub-assembly.

(2) Step 2:

1. Mark each cylinder head set bolt head with paint as shown in the illustration.

2. Tighten the cylinder head set bolts 90° in the order shown in step 1.

(3) Step 3:

1. Tighten the cylinder head set bolts another 45° in the order shown in step 1.

(4) Check that the paint marks are now at a 135° angle.

NOTICE:

Do not add engine oil for at least 2 hours after installing the cylinder head sub-assembly.

(5) After tightening the cylinder head set bolts, wipe off any seal packing that seeped out from the contact surfaces between the cylinder head sub-assembly and cylinder block sub-assembly.

NOTICE:

  • Be sure to wipe off the seal packing from inside to outside, parallel to the joint line.
  • Be sure to avoid clogging the bolt holes when wiping off the seal packing.

14. INSTALL VALVE STEM CAP

(1) Apply a light coat of engine oil to the valve stem caps.

(2) Install the 16 valve stem caps.

NOTICE:

Install each part to its original location.

15. INSTALL VALVE LASH ADJUSTER ASSEMBLY

(1) Inspect the 16 valve lash adjuster assemblies before installing them.

Click here

(2) Apply engine oil to the tips of the valve lash adjuster assemblies and install the 16 valve lash adjuster assemblies to the cylinder head sub-assembly.

NOTICE:

Install each part to its original location.

16. INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

*1

Valve Lash Adjuster Assembly

*2

No. 1 Valve Rocker Arm Sub-assembly

*3

Valve Stem Cap

-

-

(1) Install the 16 No. 1 valve rocker arm sub-assemblies as shown in the illustration.

NOTICE:

Install each part to its original location.

17. INSTALL RING PIN

NOTICE:

It is not necessary to remove ring pins unless they are being replaced.

*a

Protrusion Height

*b

20 mm

*c

13 mm

-

-

(1) Using a plastic hammer, tap 10 new ring pins into the camshaft housing sub-assembly.

Standard Ring Pin:

Item

Protrusion Height

Height

Width

Ring pin

3.0 mm (0.118 in.)

13 mm (0.512 in.)

20 mm (0.787 in.)

18. INSTALL NO. 1 CAMSHAFT BEARING

(1) Clean both surfaces of the No. 1 camshaft bearings.

(2) Install the 2 No. 1 camshaft bearings.

(3) Using a vernier caliper, measure the distance between the No. 1 camshaft bearing cap edge and the No. 1 camshaft bearing edge.

Standard Dimension (A) - (B):

0.7 mm (0.0276 in.) or less

NOTICE:

Position the No. 1 camshaft bearings to the center of the camshaft bearing cap by measuring dimensions (A) and (B).

19. INSTALL NO. 2 CAMSHAFT BEARING

(1) Clean both surfaces of the No. 2 camshaft bearings.

(2) Install the 2 No. 2 camshaft bearings.

(3) Using a vernier caliper, measure the distance between the camshaft housing sub-assembly edge and the No. 2 camshaft bearing edge.

Dimension (A):

1.05 to 1.75 mm (0.0413 to 0.0689 in.)

NOTICE:

Position the No. 2 camshaft bearings to the center of the camshaft housing sub-assembly by measuring dimension (A).

20. INSTALL OIL CONTROL VALVE FILTER

(1) Check that no foreign matter is on the mesh of the oil control valve filter.

(2) Install the oil control valve filter.

NOTICE:

Do not touch the mesh when installing the oil control valve filter.

21. INSTALL NO. 2 CAMSHAFT

Click here

22. INSTALL CAMSHAFT

HINT:

Perform "Inspection After Repair" after replacing the camshaft.

Click here

Engine Oil

-

-

(1) Clean the camshaft journals.

(2) Apply a light coat of engine oil to the camshaft journals, camshaft housing sub-assembly and camshaft bearing caps.

(3) Install the camshaft to the camshaft housing sub-assembly.

23. INSTALL CAMSHAFT BEARING CAP

*a

Knock Pin

-

-

(1) Confirm the marks and numbers on the camshaft bearing caps and place them in each proper position and direction.

(2) Tighten the 10 bearing cap bolts in the order shown in the illustration.

Torque:

16 N·m {163 kgf·cm, 12 ft·lbf}

24. INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY

*1

No. 1 Valve Rocker Arm Sub-assembly

*2

Valve Lash Adjuster Assembly

*3

Valve Stem Cap

-

-

*a

Correct

*b

Incorrect

*c

Cylinder Head Sub-assembly Upper Side

*d

Seal Packing

*e

3.5 to 4.0 mm (0.138 to 0.157 in.)

-

-

(1) Make sure that the No. 1 valve rocker arm sub-assemblies are installed as shown in the illustration.

(2) Apply seal packing in a continuous line as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, ThreeBond 1207B or equivalent

NOTICE:

  • Remove any oil from the contact surfaces.
  • Install the camshaft housing sub-assembly within 3 minutes and tighten the bolts within 10 minutes of applying seal packing.
  • Do not start the engine for at least 2 hours after installation.

(3) Set the camshaft and No. 2 camshaft as shown in the illustration.

(4) Install the camshaft housing sub-assembly and tighten the 17 bolts in the order shown in the illustration.

Torque:

27 N·m {275 kgf·cm, 20 ft·lbf}

NOTICE:

  • After installing the camshaft housing sub-assembly, make sure that the cam lobes are positioned as shown in the illustration.
  • If it is necessary to loosen any of the bolts during installation, remove the camshaft housing sub-assembly, clean the installation surfaces, and reapply seal packing.
  • If it is necessary to remove the camshaft housing sub-assembly during installation, make sure that the previously applied seal packing does not enter any oil passages.
  • After installing the camshaft housing sub-assembly, wipe off any seal packing that seeped out from between the camshaft housing sub-assembly and cylinder head sub-assembly.

25. INSTALL CAMSHAFT TIMING SPROCKET

(1) Using a wrench to hold the hexagonal portion of the No. 2 camshaft, tighten the bolt.

Torque:

54 N·m {551 kgf·cm, 40 ft·lbf}

26. INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

*1

Camshaft Timing Gear Assembly

-

-

*a

Knock Pin

*b

Knock Pin Hole

*c

Camshaft Flange

*d

No Gap

(1) Align and fit the knock pin of the camshaft to the knock pin hole of the camshaft timing gear assembly.

(2) Check that there is no gap between the camshaft timing gear assembly and camshaft flange.

(3) Using a wrench to hold the hexagonal portion of the camshaft, tighten the bolt.

Torque:

54 N·m {551 kgf·cm, 40 ft·lbf}

(4) Check that the camshaft timing gear assembly can move in the retard direction (clockwise) and locks in the most retarded position.

27. INSTALL CRANKSHAFT TIMING GEAR KEY

(1) Using a plastic hammer, tap in the 2 crankshaft timing gear keys.

HINT:

Tap in the crankshaft timing gear keys until they contact the crankshaft as shown in the illustration.

28. INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE

(1) Install the No. 1 crankshaft position sensor plate to the crankshaft with the "F" mark facing forward.

29. INSTALL NO. 2 CHAIN SUB-ASSEMBLY

*1

Crankshaft Timing Gear Key

*2

Oil Pump Drive Gear

*3

Oil Pump Drive Shaft Gear

-

-

*a

Mark Plate (Yellow)

*b

Timing Mark

*c

Front of Engine

-

-

(1) Temporarily install the crankshaft pulley set bolt to the crankshaft.

(2) Set the crankshaft timing gear keys as shown in the illustration.

(3) Turn the oil pump drive shaft so that the flat face is facing upward.

(4) Remove the crankshaft pulley set bolt from the crankshaft.

(5) Align the mark plates (yellow) with the timing mark of the oil pump drive gear and oil pump drive shaft gear as shown in the illustration.

HINT:

Make sure the mark plates (yellow) of the No. 2 chain sub-assembly are facing away from the engine assembly.

(6) With the No. 2 chain sub-assembly placed around the oil pump drive gear and oil pump drive shaft gear, install the oil pump drive gear to the crankshaft and temporarily install the oil pump drive shaft gear to the oil pump drive shaft.

(7) Temporarily install the oil pump drive shaft gear nut.

30. INSTALL CHAIN TENSIONER PLATE

*1

Chain Tensioner Plate

*2

Chain Damper Spring

(1) Install the chain damper spring to the chain tensioner plate, and then install the chain tensioner plate with the bolt.

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

(2) Temporarily install the crankshaft pulley with the crankshaft pulley set bolt.

(3) Using SST, hold the crankshaft pulley. Then tighten the oil pump drive shaft gear nut.

SST: 09213-54015

91551-00850

SST: 09330-00021

Torque:

28 N·m {286 kgf·cm, 21 ft·lbf}

(4) Remove SST, the crankshaft pulley set bolt and crankshaft pulley.

31. INSTALL CRANKSHAFT TIMING SPROCKET

32. SET NO. 1 CYLINDER TO TDC (COMPRESSION)

*1

Crankshaft Timing Gear Key

-

-

*a

Timing Mark

*b

Timing Mark (Rectangle)

*c

Mark (Circle)

-

-

(1) Temporarily install the crankshaft pulley set bolt to the crankshaft.

(2) Turn the crankshaft clockwise until the crankshaft timing gear key is facing upward.

(3) Check that the timing marks on the camshaft timing gear assembly and camshaft timing sprocket are aligned as shown in the illustration.

HINT:

There are 3 marks on the camshaft timing sprocket. Make sure that the timing mark (rectangle) is at the top.

(4) Remove the crankshaft pulley set bolt from the crankshaft.

33. INSTALL NO. 1 CHAIN VIBRATION DAMPER

Torque:

21 N·m {214 kgf·cm, 15 ft·lbf}

34. INSTALL CHAIN SUB-ASSEMBLY

Click here

35. INSTALL NO. 2 CHAIN VIBRATION DAMPER

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

36. INSTALL CHAIN TENSIONER SLIPPER

37. INSTALL OIL FILTER BRACKET WITH HEAD STRAIGHT SCREW PLUG GASKET

(1) Using a 10 mm hexagon socket wrench, install 2 new oil filter bracket with head straight screw plug gaskets and the 2 oil filter bracket with head straight screw plugs to the oil filter bracket.

Torque:

44 N·m {449 kgf·cm, 32 ft·lbf}

38. INSTALL STUD BOLT

NOTICE:

If the stud bolts are deformed or the threads are damaged, replace them.

*a

21 mm (0.827 in.)

*b

9 mm (0.354 in.)

*c

34 mm (1.34 in.)

-

-

(1) Tyep A:

1. Using an E6 "TORX" socket wrench, install the 2 stud bolts as shown in the illustration.

Torque:

5 N·m {51 kgf·cm, 44 in·lbf}

(2) Install the 2 stud bolts as shown in the illustration.

Torque:

5 N·m {51 kgf·cm, 44 in·lbf}

39. INSTALL ENGINE WATER PUMP ASSEMBLY

(1) Install a new gasket to the engine water pump assembly.

HINT:

Be sure to clean the contact surfaces.

(2) Install the engine water pump assembly to the timing chain cover sub-assembly with the 3 bolts.

Torque:

21 N·m {214 kgf·cm, 15 ft·lbf}

40. TEMPORARILY TIGHTEN TIMING CHAIN COVER SUB-ASSEMBLY

*a

Cylinder Head Sub-assembly and Cylinder Block Sub-assembly Side

*b

Timing Chain Cover Sub-assembly Side

Clean and degrease

-

-

(1) Clean the contact surfaces of the timing chain cover sub-assembly, camshaft housing sub-assembly, cylinder head sub-assembly, cylinder block sub-assembly and stiffening crankcase assembly, and confirm that no oil, moisture, or other foreign matter is on the surfaces.

(1) Install 3 new O-rings to the cylinder head sub-assembly and cylinder block sub-assembly.

(2) Apply seal packing to the engine unit as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

Seal Packing Diameter:

5.0 mm (0.197 in.)

NOTICE:

Install the timing chain cover sub-assembly within 3 minutes and tighten the bolts within 10 minutes of applying seal packing.

*a

2.5 mm

*b

5.0 mm

*c

7.5 mm

*d

2.5 to 3.5 mm

*e

4.5 to 5.5 mm

*f

7.0 to 8.0 mm

(1) Apply seal packing to the timing chain cover sub-assembly in a continuous line as shown in the illustration.

Seal Packing:

Item

Seal Packing

Dashed line

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

Continuous line

Alternate long and short dashed line

Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent

Application Specification:

Area

Seal Packing Diameter

Distance from Edge of Cover to:

Seal Packing Application Length

Distance from Top of Cover to Top of Seal Packing

Dashed line

2.5 to 3.5 mm (0.0984 to 0.138 in.)

Center of seal packing

2.5 mm (0.0984 in.)

-

-

Continuous line

4.5 to 5.5 mm (0.177 to 0.217 in.) or 7.0 to 8.0 mm (0.276 to 0.315 in.)

-

-

-

Alternate long and short dashed line

4.0 mm (0.157 in.)

Center of seal packing

3.0 mm (0.118 in.)

-

-

(A) - (A)

2.5 to 3.5 mm (0.0984 to 0.138 in.)

Center of seal packing

2.5 mm (0.0984 in.)

-

-

(B) - (B)

4.5 to 5.5 mm (0.177 to 0.217 in.)

Opposite edge of seal packing

5.0 mm (0.197 in.)

-

-

(C) - (C)

7.0 to 8.0 mm (0.276 to 0.315 in.)

Opposite edge of seal packing

7.5 mm (0.295 in.)

-

-

(F)

4.5 to 5.5 mm (0.177 to 0.217 in.)

-

15.5 mm (0.610 in.)

50.4 mm (1.98 in.)

(G)

4.5 to 5.5 mm (0.177 to 0.217 in.)

-

10.3 mm (0.406 in.)

143.1 mm (5.63 in.)

(H)

7.0 to 8.0 mm (0.276 to 0.315 in.)

-

19.5 mm (0.768 in.)

153.4 mm (6.04 in.)

(I)

4.5 to 5.5 mm (0.177 to 0.217 in.)

-

16.0 mm (0.630 in.)

385.8 mm (1.27 ft.)

(J)

4.5 to 5.5 mm (0.177 to 0.217 in.)

-

18.6 mm (0.732 in.)

51.4 mm (2.02 in.)

(K)

4.5 to 5.5 mm (0.177 to 0.217 in.)

-

25.3 mm (0.996 in.)

121.9 mm (4.80 in.)

(L)

7.0 to 8.0 mm (0.276 to 0.315 in.)

-

25.8 mm (1.02 in.)

147.2 mm (5.80 in.)

(M)

4.5 to 5.5 mm (0.177 to 0.217 in.)

-

5.1 mm (0.201 in.)

173.0 mm (6.81 in.)

(N)

4.5 to 5.5 mm (0.177 to 0.217 in.)

-

14.6 mm (0.575 in.)

385.8 mm (1.27 ft.)

(O)

4.0 mm (0.157 in.)

Center of seal packing

3.0 mm (0.118 in.)

-

-

NOTICE:

Install the timing chain cover sub-assembly within 3 minutes and tighten the bolts within 10 minutes of applying seal packing.

*1

Seal Washer

-

-

(1) Apply adhesive to 5 and a half threads or more of the end of the 2 bolts (E).

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

(2) Temporarily install the timing chain cover sub-assembly with the 18 bolts and a new seal washer.

Bolt Length:

Item

Length

Bolt (A), (E)

35 mm (1.38 in.)

Bolt (B), (D)

55 mm (2.17 in.)

Bolt (C)

40 mm (1.57 in.)

NOTICE:

Make sure that there is no oil on the threads of the bolts.

41. INSTALL ENGINE MOUNTING BRACKET RH

(1) Temporarily install the engine mounting bracket RH to the timing chain cover sub-assembly with the 3 bolts.

Bolt Length:

Item

Length

Bolt

80 mm (3.15 in.)

NOTICE:

Make sure that there is no oil on the threads of the bolts.

42. INSTALL OIL FILTER BRACKET SUB-ASSEMBLY

(1) Install 2 new oil filter bracket O-rings to the timing chain cover sub-assembly.

(2) Temporarily install the oil filter bracket sub-assembly to the timing chain cover sub-assembly with the 4 bolts.

Bolt Length:

Item

Length

Bolt

35 mm (1.38 in.)

NOTICE:

Make sure that there is no oil on the threads of the bolts.

43. TIGHTEN TIMING CHAIN COVER SUB-ASSEMBLY

*a

Torque

*b

Bolt Tightening Order

(1) Fully tighten the 25 bolts in the order shown in the illustration.

Torque:

Bolt (A), (D), (E) :

26 N·m {260 kgf·cm, 19 ft·lbf}

Bolt (B), (F) :

51 N·m {520 kgf·cm, 38 ft·lbf}

Bolt (C) :

10 N·m {102 kgf·cm, 7 ft·lbf}

NOTICE:

  • Tighten the bolts within 10 minutes of applying seal packing.
  • Do not add engine oil for at least 2 hours after installation.
  • Do not start the engine for at least 2 hours after installation.

44. INSTALL TIMING CHAIN COVER OIL SEAL

Click here

45. INSTALL WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

Click here

46. INSTALL CRANKSHAFT PULLEY

Click here

47. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

*a

Cam

*b

Hook

*c

Plunger

*d

Pin

*e

Correct

*f

Incorrect

*g

Push

*h

Raise

(1) Raise the cam, then fully push in the plunger and engage the hook with the pin so that the plunger is in the position shown in the illustration.

NOTICE:

Make sure that the cam engages with the first tooth of the plunger to allow the hook to pass over the pin.

(2) Install a new gasket, the bracket and No. 1 chain tensioner assembly to the timing chain cover sub-assembly with the 2 nuts.

Torque:

12 N·m {122 kgf·cm, 9 ft·lbf}

NOTICE:

If the hook releases the plunger while the No. 1 chain tensioner assembly is being installed, set the hook again.

*a

Hook

*b

Release

*c

Plunger

*d

Plunger is extended

(1) Rotate the crankshaft counterclockwise slightly and check that the hook is released.

(2) Turn the crankshaft clockwise and check that the plunger is extended.

48. INSTALL OIL FILTER UNION

(1) Using a 12 mm hexagon socket wrench, install the oil filter union to the oil filter bracket sub-assembly.

Torque:

30 N·m {301 kgf·cm, 22 ft·lbf}

49. INSTALL OIL FILTER SUB-ASSEMBLY

Click here

50. INSTALL SPARK PLUG TUBE GASKET

51. INSTALL CYLINDER HEAD COVER GASKET

*1

Cylinder Head Cover Sub-assembly

*2

Cylinder Head Cover Gasket

(1) Install 3 new cylinder head cover gaskets to the cylinder head cover sub-assembly.

NOTICE:

  • Remove any oil from the contact surfaces.
  • Misalignment between the center of the cylinder head cover sub-assembly rib and the center of the cylinder head gasket tab should be 4.0 mm (0.157 in.) or less.

52. INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY

Click here

53. INSTALL KNOCK CONTROL SENSOR

Click here

54. INSTALL CRANKSHAFT POSITION SENSOR

Click here

55. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

(1) Install 2 new gaskets as shown in the illustration.

(2) Apply seal packing as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

Standard Diameter:

4.0 mm (0.157 in.)

NOTICE:

  • Remove any oil from the contact surfaces.
  • Install the cylinder head cover sub-assembly within 3 minutes and tighten the bolts within 15 minutes of applying seal packing.
  • Do not start the engine for at least 2 hours after installation.

(3) Install the cylinder head cover sub-assembly with the 16 bolts.

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

NOTICE:

Misalignment between the contact surfaces of the timing chain cover sub-assembly and camshaft housing sub-assembly and the center of the cylinder head cover gasket tab should be 4.0 mm (0.157 in.) or less.

*1

Timing Chain Cover Sub-assembly

*2

Camshaft Housing Sub-assembly

*3

Cylinder Head Cover Gasket

*a

Projection

56. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

Click here

57. INSTALL CAMSHAFT POSITION SENSOR

Click here

58. INSTALL SPARK PLUG

Click here

59. INSTALL OIL FILLER CAP SUB-ASSEMBLY

Installation

INSTALLATION

COMPONENTS (INSTALLATION)

Procedure

Part Name Code

1

IGNITION COIL ASSEMBLY

19500

-

-

2

VENTILATION HOSE

12261

-

-

-

3

WATER BY-PASS PIPE

16268L

-

-

-

4

ENGINE OIL LEVEL DIPSTICK GUIDE

11452

-

-

-

5

ENGINE OIL LEVEL DIPSTICK

15301

-

-

-

N*m (kgf*cm, ft.*lbf): Specified torque

●

Non-reusable part

Procedure

Part Name Code

6

NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

17168

-

-

-

7

EXHAUST MANIFOLD (TWC: Front Catalyst)

17141

-

-

8

MANIFOLD STAY

17118

-

-

9

NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

17167

-

-

-

N*m (kgf*cm, ft.*lbf): Specified torque

●

Non-reusable part

Procedure

Part Name Code

10

WIRE HARNESS CLAMP BRACKET

-

-

-

-

11

FUEL VAPOR FEED PIPE

23818

-

-

-

12

PURGE VALVE (PURGE VSV)

17650G

-

-

-

13

FUEL INJECTOR ASSEMBLY

23250

-

-

14

NO. 1 DELIVERY PIPE SPACER

23807V

-

-

15

FUEL DELIVERY PIPE SUB-ASSEMBLY

23807

-

-

16

INTAKE MANIFOLD

17111

-

-

-

17

VENTILATION HOSE

12261

-

-

-

18

TEMPORARILY INSTALL EGR VALVE ASSEMBLY WITH EGR COOLER

25601L

-

-

19

TEMPORARILY INSTALL EGR PIPE ASSEMBLY

25610

-

-

-

20

INSTALL EGR VALVE ASSEMBLY WITH EGR COOLER

25601L

-

-

-

21

INSTALL EGR PIPE ASSEMBLY

25610

-

-

-

22

NO. 2 WATER BY-PASS HOSE

16264

-

-

-

23

WATER BY-PASS HOSE

16261

-

-

-

24

WATER OUTLET

16331

-

-

-

25

NO. 8 WATER BY-PASS HOSE

16296

-

-

-

Tightening torque for "Major areas involving basic Toyota Prius vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf)

N*m (kgf*cm, ft.*lbf): Specified torque

●

Non-reusable part

-

-

PROCEDURE

1. INSTALL IGNITION COIL ASSEMBLY

Click here

2. INSTALL VENTILATION HOSE

3. INSTALL WATER BY-PASS PIPE

Torque:

21 N·m {214 kgf·cm, 15 ft·lbf}

4. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

Click here

5. INSTALL ENGINE OIL LEVEL DIPSTICK

6. INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

Click here

7. INSTALL EXHAUST MANIFOLD (TWC: Front Catalyst)

Click here

8. INSTALL MANIFOLD STAY

Click here

9. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Click here

10. INSTALL WIRE HARNESS CLAMP BRACKET

Torque:

8 N·m {82 kgf·cm, 71 in·lbf}

11. INSTALL FUEL VAPOR FEED PIPE

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

12. INSTALL PURGE VALVE (PURGE VSV)

Click here

13. INSTALL FUEL INJECTOR ASSEMBLY

Click here

14. INSTALL NO. 1 DELIVERY PIPE SPACER

Click here

15. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

Click here

16. INSTALL INTAKE MANIFOLD

Click here

17. CONNECT VENTILATION HOSE

18. TEMPORARILY INSTALL EGR VALVE ASSEMBLY WITH EGR COOLER

(1) Install a new EGR cooler gasket.

(2) Using an E8 "TORX" socket wrench, temporarily install the EGR valve assembly with EGR cooler with the 2 stud bolts.

Torque:

9,5 N·m {97 kgf·cm, 84 in·lbf}

(3) Temporarily install the bolt and 2 nuts.

(4) Temporarily install 2 new nuts.

19. TEMPORARILY INSTALL EGR PIPE ASSEMBLY

20. INSTALL EGR VALVE ASSEMBLY WITH EGR COOLER

Bolt

Nut

Torque:

Nut (A) :

21 N·m {214 kgf·cm, 15 ft·lbf}

Nut (B) :

26 N·m {265 kgf·cm, 19 ft·lbf}

Bolt :

21 N·m {214 kgf·cm, 15 ft·lbf}

21. INSTALL EGR PIPE ASSEMBLY

Torque:

8,5 N·m {87 kgf·cm, 75 in·lbf}

22. INSTALL NO. 2 WATER BY-PASS HOSE

23. INSTALL WATER BY-PASS HOSE

24. INSTALL WATER OUTLET

Torque:

28 N·m {286 kgf·cm, 21 ft·lbf}

25. INSTALL NO. 8 WATER BY-PASS HOSE