Camshaft

In this manual: Camshaft
How To Troubleshoot Ecu Controlled Systems — 1How To Use This Manual — 1Identification Information — 1Repair Instruction — 1Terms — 12zr-fxe Air Cleaner Filter Element — 12zr-fxe Auxiliary Battery — 12zr-fxe Coolant (for Engine Coolant) — 12zr-fxe Oil And Oil Filter — 12zr-fxe Spark Plug — 1Air Conditioning Filter — 1Battery Cooling Filter — 1Brake Fluid — 1Coolant (for Inverter) — 1Front Brake Flexible Hose — 1Front Disc Brake Pad — 1Front Lower Ball Joint — 1Front Wheel Alignment — 1Front Wiper Rubber — 1General Maintenance — 1M20a-fxs Air Cleaner Filter Element — 1M20a-fxs Auxiliary Battery — 1M20a-fxs Coolant (for Engine Coolant) — 1M20a-fxs Oil And Oil Filter — 1M20a-fxs Spark Plug — 1Pa10/pb10/pb12 Hybrid Transaxle Fluid — 1Q810 Hybrid Transaxle Fluid — 1Rear Brake Flexible Hose — 1Rear Disc Brake Pad — 1Rear Wheel Alignment — 1Steering Column — 1Tire And Wheel — 1Transmitter Battery — 1When Disconnecting Or Reconnecting Battery Terminal — 1When Replacing Or Removing/installing Parts — 1Automatic High Beam Main Switch — 1Automatic High Beam System — 1Driver Monitor Camera — 1Driver Monitor Camera System — 1Driver Monitor Ecu — 1Front Camera — 1Front Camera System — 1Front Radar Sensor System — 1Front Side Radar Sensor — 1Front Side Radar Sensor System — 1Millimeter Wave Radar Sensor — 1Utility — 1Advanced Park — 1Advanced Park Main Switch — 1Amplifier Antenna — 1Audio And Visual System — 1Front Door Speaker — 1Instrument Panel Speaker — 1Microphone — 1Noise Filter — 1Pillar Speaker — 1Radio Antenna Cord (for Back Door) — 1Radio Antenna Cord (for Instrument Panel) — 1Radio Antenna Cord (for Roof) — 1Radio Receiver — 1Rear Door Speaker — 1Roof Antenna — 1Stereo Component Amplifier — 1Stereo Jack Adapter Assembly — 1Window Glass Antenna Wire — 1Back-up Battery — 1Dcm(telematics Transceiver) — 1Manual(sos)switch — 1Safety Connect System — 1Telephone And Gps Antenna (for Front Side) — 1Telephone And Gps Antenna (for Roof Side) — 1Telephone And Gps Antenna Cords — 1Garage Door Opener System (for Digital Inner Mirror) — 1Garage Door Opener System (for Ec Inner Mirror) — 1Blind Spot Monitor Sensor — 1Blind Spot Monitor System — 1Clearance Warning Ecu — 1Intuitive Parking Assist System — 1Panoramic View Monitor Switch — 1Panoramic View Monitor System — 1Parking Assist Ecu — 1Parking Assist Light — 1Parking Assist Monitor System — 1Parking Support Brake System — 1Rear View Monitor System — 1Television Camera (for Front) — 1Television Camera (for Rear) — 1Television Camera (for Side) — 1Ultrasonic Sensor (for Front) — 1Ultrasonic Sensor (for Rear) — 1Brake Actuator — 1Brake Pedal Stroke Sensor — 1Electronically Controlled Brake System — 1Front Speed Sensor — 1Rear Speed Sensor (for Awd) — 1Steering Angle Sensor — 1Brake Booster — 1Brake Fluid — 1Brake Line — 1Brake Pedal — 1Brake System — 1Electric Parking Brake Actuator — 1Electric Parking Brake Switch — 1Electric Parking Brake System — 1Forced Release — 1Front Axle Hub — 1Front Axle Hub Bolt — 1Rear Axle Carrier (for 2wd) — 1Rear Axle Carrier (for Awd) — 1Rear Axle Hub (for 2wd) — 1Rear Axle Hub (for Awd) — 1Rear Axle Hub Bolt — 1Steering Knuckle — 1Drive Shaft System — 1Front Drive Shaft Assembly — 1Rear Drive Shaft Assembly — 1Combination Switch — 1Electronic Shift Lever System — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Oil Seal — 1Hybrid Transaxle System — 1Input Shaft Oil Seal — 1Motor Cable — 1Pa10 Hybrid Vehicle Transaxle — 1Pa10 Manual Parking Lock Release — 1Pa10 Oil Cooler — 1Pb10/pb12 Hybrid Vehicle Transaxle — 1Pb10/pb12 Manual Parking Lock Release — 1Pb10/pb12 Oil Cooler — 1Shift Control Actuator — 1Shift Lever — 1Shift Lever Knob — 1Differential Side Gear Shaft — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Side Gear Oil Seal — 1Motor Cable — 1Rear Traction Motor — 1Coolant (for Engine) — 1Cooling Fan Motor — 1Cooling Fan System — 1Radiator — 1Relay — 1Thermostat — 1Water Pump — 1Canister — 1Egr Cooler — 1Egr Valve — 1Emission Control System — 1Fuel Tank Cap — 1Pcv Valve — 1Purge Valve — 1Vacuum Sensor — 1Air Fuel Ratio Sensor — 1Camshaft Oil Control Valve — 1Camshaft Position Sensor — 1Crankshaft Position Sensor — 1Ecm — 1Engine Coolant Temperature Sensor — 1Heated Oxygen Sensor — 1Ignition Coil And Spark Plug — 1Ignition System — 1Knock Sensor — 1Mass Air Flow Meter — 1Relay — 1Sfi System — 1Throttle Body — 1Camshaft — 1Cylinder Block — 1Cylinder Head — 1Cylinder Head Gasket — 1Engine — 1Engine Assembly — 1Engine Unit — 1Front Crankshaft Oil Seal — 1Rear Crankshaft Oil Seal — 1Fuel Filter — 1Fuel Injector — 1Fuel Pressure Regulator — 1Fuel Pump — 1Fuel Sender Gauge Assembly — 1Fuel System — 1Fuel Tank — 1Air Cleaner Filter Element — 1Exhaust Manifold — 1Exhaust Pipe — 1Intake Manifold — 1Intake System — 1Lubrication System — 1Oil And Oil Filter — 1Oil Pan And Oil Level Sensor — 1Oil Pressure Switch — 1Oil Pump — 1Accelerator Pedal Sensor — 1Battery Blower (for Hev Model) — 1Battery Ecu (for Hev Model) — 1Battery Ecu (for Phev Model) — 1Battery Voltage Sensor (for Phev Model) — 1Charge Cable (for Phev Model) — 1Charge Indicator (for Phev Model) — 1Charge Inlet (for Phev Model) — 1Combination Switch — 1Coolant (for Inverter) — 1Cooler (for Phev Model) — 1Electric Vehicle Charger Assembly (for Phev Model) — 1Frame Wire (for Hev Model) — 1Frame Wire (for Phev Model) — 1Heater Relay (for Phev Model) — 1Hv Battery (for Hev Model) — 1Hv Battery (for Phev Model) — 1Hv Battery Heater (for Phev Model) — 1Hv Battery Stack (for Phev Model) — 1Hv Relay Assembly (for Hev Model) — 1Hv Relay Assembly (for Phev Model) — 1Hybrid Battery System (for 2zr-fxe) — 1Hybrid Battery System (for M20a-fxs) — 1Hybrid Battery System (for Phev Model) — 1Hybrid Vehicle Control Ecu — 1Inverter With Converter (for Hev Model) — 1Motor Generator Control System (for 2zr-fxe) — 1Plug-in Charge Control System (for Phev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Service Plug Grip (for Hev Model) — 1Sub Radiator — 1Water Pump With Motor — 1Auxiliary Battery — 1Battery Current Sensor — 1Charging System — 1Solar Charging System — 1Solar Control Unit — 1Solar Roof — 1Can Communication System (for Hev Model) — 1Lin Communication System — 1Network Gateway Ecu — 1Integration Control Supply — 1Main Body Ecu — 1Power Integration System — 1Sub Battery System — 1Power Steering Ecu — 1Power Steering System — 1Heated Steering Wheel Controller — 1Heated Steering Wheel System — 1Steering Column Assembly — 1Steering Heater Switch — 1Steering Pad Switch — 1Steering System — 1Steering Wheel — 1Front Lower Ball Joint — 1Front Lower Suspension Arm (for 2zr-fxe Lh Side) — 1Front Lower Suspension Arm (for 2zr-fxe Rh Side) — 1Front Lower Suspension Arm (for M20a-fxs) — 1Front Shock Absorber — 1Front Stabilizer Bar — 1Front Suspension Member — 1Rear Coil Spring — 1Rear Lower Arm (for Awd Lh Side) — 1Rear Lower Arm (for Awd Rh Side) — 1Rear Lower Arm (for Hev Model 2wd) — 1Rear Lower Arm (for Phev Model) — 1Rear Shock Absorber — 1Rear Stabilizer Bar — 1Rear Suspension Member (for 2wd) — 1Rear Suspension Member (for Awd) — 1Rear Trailing Arm — 1Rear Upper Arm — 1Tire And Wheel System — 1Tire Repair Seal — 1Tire Pressure Warning Receiver — 1Tire Pressure Warning System — 1Tire Pressure Warning Valve — 1Acoustic Vehicle Alerting System — 1Vehicle Approaching Speaker — 1Vehicle Approaching Speaker Ecu — 1Back Door — 1Back Door Closer Ecu — 1Back Door Opener Switch — 1Back Door Support — 1Back Door Weatherstrip — 1Charge Lid Courtesy Switch — 1Charge Lid Opener Motor Assembly — 1Charge Lid Opener System — 1Charge Lid Opener Unit — 1Front Door — 1Front Door Opening Trim Weatherstrip — 1Fuel Lid Opener Motor Assembly — 1Fuel Lid Opener Switch — 1Fuel Lid Opener System — 1Hood — 1Hood Lock Control Cable Assembly — 1Power Back Door Closer Switch — 1Power Back Door Control Switch — 1Power Back Door Drive Unit — 1Power Back Door System — 1Power Back Door Touch Sensor — 1Power Back Door Warning Buzzer — 1Rear Door — 1Rear Door Opening Trim Weatherstrip — 1Reserve Lock Switch — 1Front Bumper — 1Front Door Belt Moulding — 1Front Door Window Frame Moulding — 1Front Fender — 1Front Pillar Upper Cover — 1Grille Shutter — 1Grille Shutter System — 1Name Plate — 1Quarter Garnish — 1Rear Bumper — 1Rear Door Belt Moulding — 1Rear Door Window Frame Moulding — 1Rear Wheel House Plate — 1Rocker Panel Moulding — 1Roof Drip Side Finish Moulding — 1Roof Garnish — 1Wheel Opening Moulding (for Front Side) — 1Wheel Opening Moulding (for Rear Side) — 1Windshield Outside Moulding — 1Horn — 1Horn System — 1Relay — 1Automatic Light Control Sensor — 1Back-up Light Assembly — 1Charge Lid Light — 1Front Marker Light — 1Hazard Warning Switch — 1Headlight Assembly — 1Headlight Dimmer Switch — 1Headlight Leveling Switch — 1High Mounted Stop Light Assembly — 1Illumination Light Assembly — 1License Plate Light Assembly — 1Lighting System — 1Rear Combination Light Assembly — 1Rear Light Assembly — 1Rear Side Marker Light Assembly — 1Relay — 1Side Turn Signal Light Assembly — 1Stop Light Switch — 1Switch Housing — 1Outer Mirror Switch — 1Outer Rear View Mirror — 1Outer Rear View Mirror Cover — 1Outer Rear View Mirror Glass — 1Power Mirror Control System — 1Back Door Glass — 1Front Passenger Side Power Window Switch — 1Power Window Control System — 1Power Window Master Switch — 1Power Window Regulator Motor (for Front Door) — 1Power Window Regulator Motor (for Rear Door) — 1Rear Power Window Switch — 1Relay — 1Roof Window Fix Glass — 1Window Defogger System — 1Windshield Deicer Switch — 1Windshield Deicer System — 1Windshield Glass — 1Front Wiper Motor — 1Rain Sensor — 1Relay — 1Washer Motor — 1Washer Nozzle (for Front Side) — 1Washer Nozzle (for Rear Television Camera) — 1Wiper And Washer System — 1Wiper Ecu — 1Wiper Switch — 1Back Door Lock — 1Door Control Receiver — 1Door Control Switch — 1Door Control Transmitter — 1Door Lock Release Motor (for Rear Side) — 1Door Outside Handle (for Rear Side) — 1Front Door Lock — 1Power Door Lock Control System — 1Rear Door Lock — 1Transmitter Battery — 1Wireless Door Lock Control System — 1Accumulator — 1Air Conditioning Amplifier — 1Air Conditioning Panel — 1Air Conditioning Pressure Sensor — 1Air Conditioning Unit — 1Ambient Temperature Sensor — 1Blower Unit — 1Condenser (for Hev Model) — 1Condenser (for Phev Model) — 1Discharge Temperature Sensor — 1Electric Expansion Valve (cooling) — 1Electric Expansion Valve (heating) — 1Evaporator Pipe Temperature Sensor — 1Evaporator Pressure Regulator — 1Front Blower Motor — 1Front Evaporator Front Solenoid Valve — 1Air Conditioning System (for Hev Model) — 1Front Evaporator Temperature Sensor — 1Heat Exchanger Temperature Sensor — 1Heat Pump Ecu — 1High Pressure Magnetic Valve — 1Humidity Sensor — 1Internal Condenser Temperature Sensor — 1Low Pressure Magnetic Valve — 1Refrigerant (for Hfc-134a(r134a)) — 1Refrigerant Line (for Hev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Room Temperature Sensor — 1Solar Sensor — 1Floor Carpet — 1Front Console Box — 1Instrument Panel Safety Pad — 1Roof Headlining — 1Roof Sunshade — 1Ambient Light (for Driver Side) — 1Ambient Light (for Front Passenger Side) — 1Back Door Courtesy Switch — 1Footwell Light — 1Glove Box Light — 1Lighting System — 1Luggage Compartment Room Light — 1Personal Light — 1Room Light — 1Vanity Light — 1Vanity Light Switch — 1Combination Meter — 1Meter / Gauge System — 1Trip Switch — 1Digital Inner Mirror — 1Digital Rear-view Mirror System — 1Inner Mirror Monitor Camera — 1Inner Rear View Mirror (w/o Ec Mirror) — 1Accessory Power Outlet System — 1Power Outlet Socket (for Console Box Front Side) — 1Power Outlet Socket (for Console Box Rear Side) — 1Power Outlet Socket (for Console Box) — 1Power Outlet Socket (for Luggage Compartment) — 1Power Outlet Switch — 1Wireless Charger Assembly — 1Wireless Charging System — 1Climate Control Seat System — 1Front Power Seat Control System (w/ Memory) — 1Front Power Seat Motor Assembly — 1Front Seat Assembly (for Power Seat) — 1Front Seat Cushion Heater (for Power Seat) — 1Front Seatback Heater (for Power Seat) — 1Lumbar Support Adjuster Assembly — 1Power Seat Control Ecu — 1Power Seat Switch — 1Power Seat Track Rail Assembly — 1Rear Seat Assembly — 1Rear Seat Cushion Heater — 1Rear Seat Reminder System — 1Rear Seatback Heater — 1Seat Heater Control — 1Seat Heater Switch (for Front Seat) — 1Seat Heater Switch (for Rear Side) — 1Seat Heater System — 1Seat Memory Switch — 1Child Restraint Seat Anchor Bracket — 1Front Seat Inner Belt Assembly — 1Front Seat Outer Belt Assembly — 1Occupant Detection Sensor (for Front Passenger Side) — 1Rear Center Seat Outer Belt Assembly — 1Rear Seat Inner Belt Assembly (for Rh Side) — 1Rear Seat Outer Belt Assembly — 1Seat Belt Warning System (w/ Occupant Classification System) — 1Tongue Plate Stopper — 1Airbag System — 1Center Airbag Sensor Assembly — 1Curtain Shield Airbag Assembly — 1Front Airbag Sensor — 1Front Passenger Airbag Assembly — 1Front Seat Side Airbag Assembly — 1Inspection After Collision — 1Knee Airbag Assembly — 1Occupant Classification System — 1Rear Seat Side Airbag Assembly — 1Side Airbag Sensor (for Center Pillar) — 1Side Airbag Sensor (for Front Door) — 1Spiral Cable — 1Steering Pad — 1Certification Ecu — 1Digital Key Ecu — 1Digital Key Receiver (for Front Floor) — 1Digital Key Receiver (for Outside Luggage Compartment) — 1Digital Key Receiver (for Rear Door) — 1Digital Key System — 1Electrical Key Oscillator (for Front Floor) — 1Electrical Key Oscillator (for Outside Luggage Compartment) — 1Electrical Key Oscillator (for Rear Floor) — 1Engine Hood Courtesy Switch — 1Id Code Box — 1Smart Key System (for Start Function) — 1
~12min read
1special tools
010203040502720N·mlb·ft
Tightening torque found on this page
  • Removal
  • Installation

Removal

REMOVAL

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during camshaft removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

  • Replacement of throttle body assembly
  • Replacement of camshaft (for intake or exhaust camshaft)
  • Replacement of camshaft timing gear assembly
  • Replacement of ignition coil assembly

Inspection After Repair

  • Poor idle, etc.
  • Engine start function, etc.
COMPONENTS (REMOVAL)

Procedure

Part Name Code

1

NO. 1 ENGINE UNDER COVER ASSEMBLY

51410

-

-

-

2

DRAIN ENGINE COOLANT (for Engine)

-

-

-

Procedure

Part Name Code

3

WINDSHIELD WIPER MOTOR AND LINK

-

-

-

-

4

WATER GUARD PLATE

55734D

-

-

-

5

OUTER COWL TOP PANEL

55711

-

-

-

Procedure

Part Name Code

6

NO. 2 VENTILATION HOSE

12262

-

-

-

7

IGNITION COIL ASSEMBLY

19500

-

-

8

CAMSHAFT POSITION SENSOR

11101E

-

-

9

ENGINE WIRE

82121

-

-

-

10

NO. 1 FUEL VAPOR FEED HOSE

23826

-

-

-

11

FUEL VAPOR FEED PIPE

23818

-

-

-

●

Non-reusable part

★

Precoated part

Procedure

Part Name Code

12

CYLINDER HEAD COVER SUB-ASSEMBLY

11201

-

-

13

CYLINDER HEAD COVER GASKET

11213

-

-

-

14

SPARK PLUG TUBE GASKET

11193

-

-

15

SET NO. 1 CYLINDER TO TDC (COMPRESSION)

-

-

-

16

NO. 2 CHAIN VIBRATION DAMPER

13562

-

-

17

NO. 1 CHAIN TENSIONER ASSEMBLY

13540

-

-

18

CAMSHAFT TIMING SPROCKET

13523G

-

-

19

INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

13050

-

-

20

CAMSHAFT BEARING CAP

-

-

-

21

NO. 2 CAMSHAFT

13512

-

-

-

22

CAMSHAFT

13511

-

-

23

REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

13050

-

-

24

NO. 1 CAMSHAFT BEARING

-

-

-

-

25

NO. 2 CAMSHAFT BEARING

-

-

-

-

●

Non-reusable part

-

-

PROCEDURE

1. REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Click here

2. DRAIN ENGINE COOLANT (for Engine)

Click here

3. REMOVE WINDSHIELD WIPER MOTOR AND LINK

Click here

4. REMOVE WATER GUARD PLATE

Click here

5. REMOVE OUTER COWL TOP PANEL

Click here

6. DISCONNECT NO. 2 VENTILATION HOSE

Click here

7. REMOVE IGNITION COIL ASSEMBLY

Click here

8. REMOVE CAMSHAFT POSITION SENSOR

Click here

9. DISCONNECT ENGINE WIRE

10. DISCONNECT NO. 1 FUEL VAPOR FEED HOSE

Click here

11. REMOVE FUEL VAPOR FEED PIPE

Click here

12. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Click here

13. REMOVE CYLINDER HEAD COVER GASKET

Click here

14. REMOVE SPARK PLUG TUBE GASKET

Click here

15. SET NO. 1 CYLINDER TO TDC (COMPRESSION)

  • Set the No. 1 cylinder to TDC (Compression)

    Click here

*a

Paint Mark

*b

Timing Mark

(1) Place paint marks on the chain sub-assembly in alignment with the timing marks on the camshaft timing gear assembly and camshaft timing sprocket.

16. REMOVE NO. 2 CHAIN VIBRATION DAMPER

(1) Using SST, remove the 2 bolts and No. 2 chain vibration damper from the No. 1 camshaft bearing cap.

SST: 09961-00950

17. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

Click here

18. REMOVE CAMSHAFT TIMING SPROCKET

*a

14 mm Union Nut Wrench

*b

Hold

*c

Turn

-

-

(1) While holding the hexagonal portion of the No. 2 camshaft with a wrench, remove the bolt with SST and 14 mm union nut wrench.

SST: 09961-00950

(2) While removing the chain sub-assembly, pull out the camshaft timing sprocket horizontally and then upward.

19. INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

Click here

20. REMOVE CAMSHAFT BEARING CAP

(1) Uniformly loosen and remove the 10 bolts in the order shown in the illustration.

NOTICE:

Do not loosen the other bearing cap bolts in this step.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.

*a

The removal order of the parts

*b

The installation order of the service bolts and spacers for temporarily tightening the camshaft housing sub-assembly

*c

Service bolt and spacer (Used to temporarily secure the camshaft housing sub-assembly)

-

-

(1) Remove the bolts and camshaft bearing caps in the order shown in the illustration. Immediately after removing each camshaft bearing cap, install service bolts and spacers in the order shown in the illustration.

Torque:

27 N·m {275 kgf·cm, 20 ft·lbf}

NOTICE:

  • If the bolts are loosened all at once, seal packing on the camshaft housing sub-assembly and cylinder head sub-assembly may separate, resulting in oil leaks. Therefore, be sure to install the service bolts and spacers to one camshaft bearing cap at a time.
  • Do not install the camshaft bearing caps when installing the service bolts and spacers.

HINT:

  • Arrange the removed parts in such a way that they can be reinstalled to their original locations.
  • Part number for the service bolt used to temporarily secure the camshaft housing sub-assembly: 91551-G0875 (15 bolts)
  • Part number for the spacer used to temporarily secure the camshaft housing sub-assembly: 90387-12048 (15 spacers)

21. REMOVE NO. 2 CAMSHAFT

22. REMOVE CAMSHAFT

(1) Hold up the chain sub-assembly and remove the camshaft from the camshaft housing sub-assembly.

(2) Suspend the chain sub-assembly with a string or equivalent.

23. REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

*a

Do not remove

-

-

(1) Secure the hexagonal portion of the camshaft in a soft jaw vise.

(2) Remove the bolt and camshaft timing gear assembly.

NOTICE:

  • Before removing the camshaft timing gear assembly, make sure that the lock pin has been released.
  • Do not remove the other 4 bolts.
  • Keep the camshaft timing gear assembly horizontal while removing it from the camshaft.
  • If the camshaft timing gear assembly is to be reused, be sure to install it with the lock pin released.

24. REMOVE NO. 1 CAMSHAFT BEARING

Click here

25. REMOVE NO. 2 CAMSHAFT BEARING

Click here

Installation

INSTALLATION

COMPONENTS (INSTALLATION)

Procedure

Part Name Code

1

NO. 1 CAMSHAFT BEARING

-

-

-

2

NO. 2 CAMSHAFT BEARING

-

-

-

3

CAMSHAFT TIMING GEAR ASSEMBLY

13050

-

-

4

NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

13801

-

-

5

CAMSHAFT

13511

-

-

6

NO. 2 CAMSHAFT

13512

-

-

7

CAMSHAFT BEARING CAP

-

-

-

8

CAMSHAFT TIMING SPROCKET

13523G

-

-

9

NO. 1 CHAIN TENSIONER ASSEMBLY

13540

-

-

10

NO. 2 CHAIN VIBRATION DAMPER

13562

-

-

11

SET NO. 1 CYLINDER TO TDC (COMPRESSION)

-

-

-

12

SPARK PLUG TUBE GASKET

11193

-

-

-

13

CYLINDER HEAD COVER GASKET

11213

-

-

14

CYLINDER HEAD COVER SUB-ASSEMBLY

11201

-

-

N*m (kgf*cm, ft.*lbf): Specified torque

*T1

For use with SST

*T2

For use with SST and a union nut wrench

●

Non-reusable part

Procedure

Part Name Code

15

FUEL VAPOR FEED PIPE

23818

-

-

-

16

NO. 1 FUEL VAPOR FEED HOSE

23826

-

-

-

17

ENGINE WIRE

82121

-

-

-

18

CAMSHAFT POSITION SENSOR

11101E

-

-

19

IGNITION COIL ASSEMBLY

19500

-

-

20

NO. 2 VENTILATION HOSE

12262

-

-

-

N*m (kgf*cm, ft.*lbf): Specified torque

*

For use with a union nut wrench

●

Non-reusable part

★

Precoated part

Procedure

Part Name Code

21

OUTER COWL TOP PANEL

55711

-

-

-

22

WATER GUARD PLATE

55734D

-

-

-

23

WINDSHIELD WIPER MOTOR AND LINK

-

-

-

-

Tightening torque for "Major areas involving basic Toyota Prius vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf)

N*m (kgf*cm, ft.*lbf): Specified torque

Procedure

Part Name Code

24

ADD ENGINE COOLANT (for Engine)

-

-

-

25

INSPECT FOR COOLANT LEAK (for Engine)

-

-

-

26

NO. 1 ENGINE UNDER COVER ASSEMBLY

51410

-

-

-

N*m (kgf*cm, ft.*lbf): Specified torque

-

-

PROCEDURE

1. INSTALL NO. 1 CAMSHAFT BEARING

Click here

2. INSTALL NO. 2 CAMSHAFT BEARING

Click here

3. INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

HINT:

Perform "Inspection After Repair" after replacing the camshaft timing gear assembly.

Click here

*a

Knock Pin

*b

Knock Pin Hole

(1) Secure the hexagonal portion of the camshaft in a soft jaw vise.

(2) Align and fit the knock pin of the camshaft to the knock pin hole of the camshaft timing gear assembly.

*1

Camshaft Timing Gear Assembly

-

-

*a

Camshaft Flange

*b

No Gap

Lock

-

-

(1) Check that there is no gap between the camshaft timing gear assembly and camshaft flange.

(2) Tighten the bolt with the camshaft timing gear assembly secured in place.

Torque:

54 N·m {551 kgf·cm, 40 ft·lbf}

NOTICE:

When tightening the bolt, do not allow the camshaft timing gear assembly to rotate.

(3) Check that the camshaft timing gear assembly can move in the retard direction (clockwise) and locks in the most retarded position.

4. SET NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

*1

No. 1 Valve Rocker Arm Sub-assembly

*2

Valve Lash Adjuster Assembly

*3

Valve Stem Cap

-

-

*a

Correct

*b

Incorrect

(1) Make sure that the No. 1 valve rocker arm subassemblies are installed as shown in the illustration.

5. INSTALL CAMSHAFT

HINT:

Perform "Inspection After Repair" after replacing the camshaft.

Click here

(1) Clean the camshaft journals.

(1) Apply a light coat of engine oil to the camshaft journals, camshaft housing sub-assembly and camshaft bearing caps.

*a

Paint Mark

*b

Timing Mark

(1) Hold up the chain sub-assembly, align the timing mark with the paint mark and install the camshaft.

6. INSTALL NO. 2 CAMSHAFT

HINT:

Perform "Inspection After Repair" after replacing the No. 2 camshaft.

Click here

(1) Clean the No. 2 camshaft journals.

(1) Apply a light coat of engine oil to the No. 2 camshaft journals, camshaft housing sub-assembly and camshaft bearing caps.

(1) Install the No. 2 camshaft to the camshaft housing sub-assembly.

7. INSTALL CAMSHAFT BEARING CAP

*a

Service bolt and spacer (Used to temporarily secure the camshaft housing sub-assembly)

*b

Knock Pin

*c

Paint Mark

*d

Timing Mark

*e

The removal order of the service bolts and spacers for temporarily tightening the camshaft housing sub-assembly

*f

The installation order of the parts

(1) Check the marks and numbers on the camshaft bearing caps, and then remove the service bolts and spacers in the order shown in the illustration. Immediately after removing the service bolts and spacers for each camshaft bearing cap, install the camshaft bearing cap with the bolts in the order shown in the illustration.

Torque:

27 N·m {275 kgf·cm, 20 ft·lbf}

NOTICE:

If the bolts are loosened all at once, seal packing on the camshaft housing sub-assembly and cylinder head sub-assembly may separate, resulting in oil leaks. Therefore, be sure to remove the service bolts and spacers from one camshaft bearing cap at a time.

HINT:

Make sure that the orientation of the straight pin, timing mark and paint mark of the camshaft are as shown in the illustration.

(1) Tighten the 10 bolts in the order shown in the illustration.

Torque:

16 N·m {163 kgf·cm, 12 ft·lbf}

(2) Check the torque of each bolt again.

8. INSTALL CAMSHAFT TIMING SPROCKET

*a

Paint Mark

*b

Timing Mark

(1) Hold the hexagonal portion of the camshaft with a wrench and turn the camshaft slightly counterclockwise to release the chain sub-assembly.

NOTICE:

Do not turn the camshaft more than necessary.

(2) Align the paint mark with the timing mark to install the chain sub-assembly.

*a

14 mm Union Nut Wrench

*b

Torque Wrench Fulcrum Length

*c

Hold

*d

Turn

(1) Using SST, a 14 mm union nut wrench and a wrench, hold the hexagonal portion of the No. 2 camshaft and install the camshaft timing sprocket to the No. 2 camshaft with the bolt.

SST: 09961-00950

Torque:

Specified tightening torque

54 N*m (551 kgf*cm, 40 ft.*lbf)

HINT:

  • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

    Click here

  • When using a 14 mm union nut wrench (fulcrum length of 25 mm (0.984 in.)) SST (fulcrum length of 150 mm (5.91 in.)) torque wrench (fulcrum length of 255 mm (10.0 in.)): 32 N*m (326 kgf*cm, 24 ft.*lbf)

9. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

Click here

10. INSTALL NO. 2 CHAIN VIBRATION DAMPER

*a

Torque Wrench Fulcrum Length

-

-

(1) Using SST, install the No. 2 chain vibration damper to the No. 1 camshaft bearing cap with the 2 bolts.

SST: 09961-00950

Torque:

Specified tightening torque

10 N*m (102 kgf*cm, 7 ft.*lbf)

HINT:

  • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

    Click here

  • When using SST ((fulcrum length of 150 mm (5.91 in.)) torque wrench (fulcrum length of 162 mm (6.38 in.)): 5.2 N*m (53 kgf*cm, 46 in.*lbf)

11. SET NO. 1 CYLINDER TO TDC (COMPRESSION)

Click here

12. INSTALL SPARK PLUG TUBE GASKET

Click here

13. INSTALL CYLINDER HEAD COVER GASKET

Click here

14. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Click here

15. INSTALL FUEL VAPOR FEED PIPE

Click here

16. CONNECT NO. 1 FUEL VAPOR FEED HOSE

Click here

17. CONNECT ENGINE WIRE

Torque:

8 N·m {82 kgf·cm, 71 in·lbf}

18. INSTALL CAMSHAFT POSITION SENSOR

Click here

19. INSTALL IGNITION COIL ASSEMBLY

Click here

20. CONNECT NO. 2 VENTILATION HOSE

Click here

21. INSTALL OUTER COWL TOP PANEL

Click here

22. INSTALL WATER GUARD PLATE

23. INSTALL WINDSHIELD WIPER MOTOR AND LINK

Click here

24. ADD ENGINE COOLANT (for Engine)

Click here

25. INSPECT FOR COOLANT LEAK (for Engine)

Click here

26. INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY

Click here