Power Back Door System

In this manual: Power Back Door System
How To Troubleshoot Ecu Controlled Systems — 1How To Use This Manual — 1Identification Information — 1Repair Instruction — 1Terms — 12zr-fxe Air Cleaner Filter Element — 12zr-fxe Auxiliary Battery — 12zr-fxe Coolant (for Engine Coolant) — 12zr-fxe Oil And Oil Filter — 12zr-fxe Spark Plug — 1Air Conditioning Filter — 1Battery Cooling Filter — 1Brake Fluid — 1Coolant (for Inverter) — 1Front Brake Flexible Hose — 1Front Disc Brake Pad — 1Front Lower Ball Joint — 1Front Wheel Alignment — 1Front Wiper Rubber — 1General Maintenance — 1M20a-fxs Air Cleaner Filter Element — 1M20a-fxs Auxiliary Battery — 1M20a-fxs Coolant (for Engine Coolant) — 1M20a-fxs Oil And Oil Filter — 1M20a-fxs Spark Plug — 1Pa10/pb10/pb12 Hybrid Transaxle Fluid — 1Q810 Hybrid Transaxle Fluid — 1Rear Brake Flexible Hose — 1Rear Disc Brake Pad — 1Rear Wheel Alignment — 1Steering Column — 1Tire And Wheel — 1Transmitter Battery — 1When Disconnecting Or Reconnecting Battery Terminal — 1When Replacing Or Removing/installing Parts — 1Automatic High Beam Main Switch — 1Automatic High Beam System — 1Driver Monitor Camera — 1Driver Monitor Camera System — 1Driver Monitor Ecu — 1Front Camera — 1Front Camera System — 1Front Radar Sensor System — 1Front Side Radar Sensor — 1Front Side Radar Sensor System — 1Millimeter Wave Radar Sensor — 1Utility — 1Advanced Park — 1Advanced Park Main Switch — 1Amplifier Antenna — 1Audio And Visual System — 1Front Door Speaker — 1Instrument Panel Speaker — 1Microphone — 1Noise Filter — 1Pillar Speaker — 1Radio Antenna Cord (for Back Door) — 1Radio Antenna Cord (for Instrument Panel) — 1Radio Antenna Cord (for Roof) — 1Radio Receiver — 1Rear Door Speaker — 1Roof Antenna — 1Stereo Component Amplifier — 1Stereo Jack Adapter Assembly — 1Window Glass Antenna Wire — 1Back-up Battery — 1Dcm(telematics Transceiver) — 1Manual(sos)switch — 1Safety Connect System — 1Telephone And Gps Antenna (for Front Side) — 1Telephone And Gps Antenna (for Roof Side) — 1Telephone And Gps Antenna Cords — 1Garage Door Opener System (for Digital Inner Mirror) — 1Garage Door Opener System (for Ec Inner Mirror) — 1Blind Spot Monitor Sensor — 1Blind Spot Monitor System — 1Clearance Warning Ecu — 1Intuitive Parking Assist System — 1Panoramic View Monitor Switch — 1Panoramic View Monitor System — 1Parking Assist Ecu — 1Parking Assist Light — 1Parking Assist Monitor System — 1Parking Support Brake System — 1Rear View Monitor System — 1Television Camera (for Front) — 1Television Camera (for Rear) — 1Television Camera (for Side) — 1Ultrasonic Sensor (for Front) — 1Ultrasonic Sensor (for Rear) — 1Brake Actuator — 1Brake Pedal Stroke Sensor — 1Electronically Controlled Brake System — 1Front Speed Sensor — 1Rear Speed Sensor (for Awd) — 1Steering Angle Sensor — 1Brake Booster — 1Brake Fluid — 1Brake Line — 1Brake Pedal — 1Brake System — 1Electric Parking Brake Actuator — 1Electric Parking Brake Switch — 1Electric Parking Brake System — 1Forced Release — 1Front Axle Hub — 1Front Axle Hub Bolt — 1Rear Axle Carrier (for 2wd) — 1Rear Axle Carrier (for Awd) — 1Rear Axle Hub (for 2wd) — 1Rear Axle Hub (for Awd) — 1Rear Axle Hub Bolt — 1Steering Knuckle — 1Drive Shaft System — 1Front Drive Shaft Assembly — 1Rear Drive Shaft Assembly — 1Combination Switch — 1Electronic Shift Lever System — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Oil Seal — 1Hybrid Transaxle System — 1Input Shaft Oil Seal — 1Motor Cable — 1Pa10 Hybrid Vehicle Transaxle — 1Pa10 Manual Parking Lock Release — 1Pa10 Oil Cooler — 1Pb10/pb12 Hybrid Vehicle Transaxle — 1Pb10/pb12 Manual Parking Lock Release — 1Pb10/pb12 Oil Cooler — 1Shift Control Actuator — 1Shift Lever — 1Shift Lever Knob — 1Differential Side Gear Shaft — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Side Gear Oil Seal — 1Motor Cable — 1Rear Traction Motor — 1Coolant (for Engine) — 1Cooling Fan Motor — 1Cooling Fan System — 1Radiator — 1Relay — 1Thermostat — 1Water Pump — 1Canister — 1Egr Cooler — 1Egr Valve — 1Emission Control System — 1Fuel Tank Cap — 1Pcv Valve — 1Purge Valve — 1Vacuum Sensor — 1Air Fuel Ratio Sensor — 1Camshaft Oil Control Valve — 1Camshaft Position Sensor — 1Crankshaft Position Sensor — 1Ecm — 1Engine Coolant Temperature Sensor — 1Heated Oxygen Sensor — 1Ignition Coil And Spark Plug — 1Ignition System — 1Knock Sensor — 1Mass Air Flow Meter — 1Relay — 1Sfi System — 1Throttle Body — 1Camshaft — 1Cylinder Block — 1Cylinder Head — 1Cylinder Head Gasket — 1Engine — 1Engine Assembly — 1Engine Unit — 1Front Crankshaft Oil Seal — 1Rear Crankshaft Oil Seal — 1Fuel Filter — 1Fuel Injector — 1Fuel Pressure Regulator — 1Fuel Pump — 1Fuel Sender Gauge Assembly — 1Fuel System — 1Fuel Tank — 1Air Cleaner Filter Element — 1Exhaust Manifold — 1Exhaust Pipe — 1Intake Manifold — 1Intake System — 1Lubrication System — 1Oil And Oil Filter — 1Oil Pan And Oil Level Sensor — 1Oil Pressure Switch — 1Oil Pump — 1Accelerator Pedal Sensor — 1Battery Blower (for Hev Model) — 1Battery Ecu (for Hev Model) — 1Battery Ecu (for Phev Model) — 1Battery Voltage Sensor (for Phev Model) — 1Charge Cable (for Phev Model) — 1Charge Indicator (for Phev Model) — 1Charge Inlet (for Phev Model) — 1Combination Switch — 1Coolant (for Inverter) — 1Cooler (for Phev Model) — 1Electric Vehicle Charger Assembly (for Phev Model) — 1Frame Wire (for Hev Model) — 1Frame Wire (for Phev Model) — 1Heater Relay (for Phev Model) — 1Hv Battery (for Hev Model) — 1Hv Battery (for Phev Model) — 1Hv Battery Heater (for Phev Model) — 1Hv Battery Stack (for Phev Model) — 1Hv Relay Assembly (for Hev Model) — 1Hv Relay Assembly (for Phev Model) — 1Hybrid Battery System (for 2zr-fxe) — 1Hybrid Battery System (for M20a-fxs) — 1Hybrid Battery System (for Phev Model) — 1Hybrid Vehicle Control Ecu — 1Inverter With Converter (for Hev Model) — 1Motor Generator Control System (for 2zr-fxe) — 1Plug-in Charge Control System (for Phev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Service Plug Grip (for Hev Model) — 1Sub Radiator — 1Water Pump With Motor — 1Auxiliary Battery — 1Battery Current Sensor — 1Charging System — 1Solar Charging System — 1Solar Control Unit — 1Solar Roof — 1Can Communication System (for Hev Model) — 1Lin Communication System — 1Network Gateway Ecu — 1Integration Control Supply — 1Main Body Ecu — 1Power Integration System — 1Sub Battery System — 1Power Steering Ecu — 1Power Steering System — 1Heated Steering Wheel Controller — 1Heated Steering Wheel System — 1Steering Column Assembly — 1Steering Heater Switch — 1Steering Pad Switch — 1Steering System — 1Steering Wheel — 1Front Lower Ball Joint — 1Front Lower Suspension Arm (for 2zr-fxe Lh Side) — 1Front Lower Suspension Arm (for 2zr-fxe Rh Side) — 1Front Lower Suspension Arm (for M20a-fxs) — 1Front Shock Absorber — 1Front Stabilizer Bar — 1Front Suspension Member — 1Rear Coil Spring — 1Rear Lower Arm (for Awd Lh Side) — 1Rear Lower Arm (for Awd Rh Side) — 1Rear Lower Arm (for Hev Model 2wd) — 1Rear Lower Arm (for Phev Model) — 1Rear Shock Absorber — 1Rear Stabilizer Bar — 1Rear Suspension Member (for 2wd) — 1Rear Suspension Member (for Awd) — 1Rear Trailing Arm — 1Rear Upper Arm — 1Tire And Wheel System — 1Tire Repair Seal — 1Tire Pressure Warning Receiver — 1Tire Pressure Warning System — 1Tire Pressure Warning Valve — 1Acoustic Vehicle Alerting System — 1Vehicle Approaching Speaker — 1Vehicle Approaching Speaker Ecu — 1Back Door — 1Back Door Closer Ecu — 1Back Door Opener Switch — 1Back Door Support — 1Back Door Weatherstrip — 1Charge Lid Courtesy Switch — 1Charge Lid Opener Motor Assembly — 1Charge Lid Opener System — 1Charge Lid Opener Unit — 1Front Door — 1Front Door Opening Trim Weatherstrip — 1Fuel Lid Opener Motor Assembly — 1Fuel Lid Opener Switch — 1Fuel Lid Opener System — 1Hood — 1Hood Lock Control Cable Assembly — 1Power Back Door Closer Switch — 1Power Back Door Control Switch — 1Power Back Door Drive Unit — 1Power Back Door System — 1Power Back Door Touch Sensor — 1Power Back Door Warning Buzzer — 1Rear Door — 1Rear Door Opening Trim Weatherstrip — 1Reserve Lock Switch — 1Front Bumper — 1Front Door Belt Moulding — 1Front Door Window Frame Moulding — 1Front Fender — 1Front Pillar Upper Cover — 1Grille Shutter — 1Grille Shutter System — 1Name Plate — 1Quarter Garnish — 1Rear Bumper — 1Rear Door Belt Moulding — 1Rear Door Window Frame Moulding — 1Rear Wheel House Plate — 1Rocker Panel Moulding — 1Roof Drip Side Finish Moulding — 1Roof Garnish — 1Wheel Opening Moulding (for Front Side) — 1Wheel Opening Moulding (for Rear Side) — 1Windshield Outside Moulding — 1Horn — 1Horn System — 1Relay — 1Automatic Light Control Sensor — 1Back-up Light Assembly — 1Charge Lid Light — 1Front Marker Light — 1Hazard Warning Switch — 1Headlight Assembly — 1Headlight Dimmer Switch — 1Headlight Leveling Switch — 1High Mounted Stop Light Assembly — 1Illumination Light Assembly — 1License Plate Light Assembly — 1Lighting System — 1Rear Combination Light Assembly — 1Rear Light Assembly — 1Rear Side Marker Light Assembly — 1Relay — 1Side Turn Signal Light Assembly — 1Stop Light Switch — 1Switch Housing — 1Outer Mirror Switch — 1Outer Rear View Mirror — 1Outer Rear View Mirror Cover — 1Outer Rear View Mirror Glass — 1Power Mirror Control System — 1Back Door Glass — 1Front Passenger Side Power Window Switch — 1Power Window Control System — 1Power Window Master Switch — 1Power Window Regulator Motor (for Front Door) — 1Power Window Regulator Motor (for Rear Door) — 1Rear Power Window Switch — 1Relay — 1Roof Window Fix Glass — 1Window Defogger System — 1Windshield Deicer Switch — 1Windshield Deicer System — 1Windshield Glass — 1Front Wiper Motor — 1Rain Sensor — 1Relay — 1Washer Motor — 1Washer Nozzle (for Front Side) — 1Washer Nozzle (for Rear Television Camera) — 1Wiper And Washer System — 1Wiper Ecu — 1Wiper Switch — 1Back Door Lock — 1Door Control Receiver — 1Door Control Switch — 1Door Control Transmitter — 1Door Lock Release Motor (for Rear Side) — 1Door Outside Handle (for Rear Side) — 1Front Door Lock — 1Power Door Lock Control System — 1Rear Door Lock — 1Transmitter Battery — 1Wireless Door Lock Control System — 1Accumulator — 1Air Conditioning Amplifier — 1Air Conditioning Panel — 1Air Conditioning Pressure Sensor — 1Air Conditioning Unit — 1Ambient Temperature Sensor — 1Blower Unit — 1Condenser (for Hev Model) — 1Condenser (for Phev Model) — 1Discharge Temperature Sensor — 1Electric Expansion Valve (cooling) — 1Electric Expansion Valve (heating) — 1Evaporator Pipe Temperature Sensor — 1Evaporator Pressure Regulator — 1Front Blower Motor — 1Front Evaporator Front Solenoid Valve — 1Air Conditioning System (for Hev Model) — 1Front Evaporator Temperature Sensor — 1Heat Exchanger Temperature Sensor — 1Heat Pump Ecu — 1High Pressure Magnetic Valve — 1Humidity Sensor — 1Internal Condenser Temperature Sensor — 1Low Pressure Magnetic Valve — 1Refrigerant (for Hfc-134a(r134a)) — 1Refrigerant Line (for Hev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Room Temperature Sensor — 1Solar Sensor — 1Floor Carpet — 1Front Console Box — 1Instrument Panel Safety Pad — 1Roof Headlining — 1Roof Sunshade — 1Ambient Light (for Driver Side) — 1Ambient Light (for Front Passenger Side) — 1Back Door Courtesy Switch — 1Footwell Light — 1Glove Box Light — 1Lighting System — 1Luggage Compartment Room Light — 1Personal Light — 1Room Light — 1Vanity Light — 1Vanity Light Switch — 1Combination Meter — 1Meter / Gauge System — 1Trip Switch — 1Digital Inner Mirror — 1Digital Rear-view Mirror System — 1Inner Mirror Monitor Camera — 1Inner Rear View Mirror (w/o Ec Mirror) — 1Accessory Power Outlet System — 1Power Outlet Socket (for Console Box Front Side) — 1Power Outlet Socket (for Console Box Rear Side) — 1Power Outlet Socket (for Console Box) — 1Power Outlet Socket (for Luggage Compartment) — 1Power Outlet Switch — 1Wireless Charger Assembly — 1Wireless Charging System — 1Climate Control Seat System — 1Front Power Seat Control System (w/ Memory) — 1Front Power Seat Motor Assembly — 1Front Seat Assembly (for Power Seat) — 1Front Seat Cushion Heater (for Power Seat) — 1Front Seatback Heater (for Power Seat) — 1Lumbar Support Adjuster Assembly — 1Power Seat Control Ecu — 1Power Seat Switch — 1Power Seat Track Rail Assembly — 1Rear Seat Assembly — 1Rear Seat Cushion Heater — 1Rear Seat Reminder System — 1Rear Seatback Heater — 1Seat Heater Control — 1Seat Heater Switch (for Front Seat) — 1Seat Heater Switch (for Rear Side) — 1Seat Heater System — 1Seat Memory Switch — 1Child Restraint Seat Anchor Bracket — 1Front Seat Inner Belt Assembly — 1Front Seat Outer Belt Assembly — 1Occupant Detection Sensor (for Front Passenger Side) — 1Rear Center Seat Outer Belt Assembly — 1Rear Seat Inner Belt Assembly (for Rh Side) — 1Rear Seat Outer Belt Assembly — 1Seat Belt Warning System (w/ Occupant Classification System) — 1Tongue Plate Stopper — 1Airbag System — 1Center Airbag Sensor Assembly — 1Curtain Shield Airbag Assembly — 1Front Airbag Sensor — 1Front Passenger Airbag Assembly — 1Front Seat Side Airbag Assembly — 1Inspection After Collision — 1Knee Airbag Assembly — 1Occupant Classification System — 1Rear Seat Side Airbag Assembly — 1Side Airbag Sensor (for Center Pillar) — 1Side Airbag Sensor (for Front Door) — 1Spiral Cable — 1Steering Pad — 1Certification Ecu — 1Digital Key Ecu — 1Digital Key Receiver (for Front Floor) — 1Digital Key Receiver (for Outside Luggage Compartment) — 1Digital Key Receiver (for Rear Door) — 1Digital Key System — 1Electrical Key Oscillator (for Front Floor) — 1Electrical Key Oscillator (for Outside Luggage Compartment) — 1Electrical Key Oscillator (for Rear Floor) — 1Engine Hood Courtesy Switch — 1Id Code Box — 1Smart Key System (for Start Function) — 1
~91min read
  • Precaution
  • Parts Location
  • System Diagram
  • How To Proceed With Troubleshooting
  • Operation Check
  • Customize Parameters
  • Problem Symptoms Table
  • Terminals Of Ecu
  • Freeze Frame Data
  • Data List / Active Test
  • VEHICLE CONTROL HISTORY (RoB)
  • Back Door Motor Internal Electronic Failure (B222049)
  • PBD Unit Pulse Sensor LH Circuit No Signal (B222631)
  • PBD Touch Sensor LH Circuit Circuit Open (B222A13)
  • Back Door Closer General Electrical Failure (B225001)
  • Back Door Closer Switch General Electrical Failure (B225101)
  • Lost Communication with ECM/PCM "A" Missing Message (U010087,U010187,U012987,U014087,U015587,U016387,U016887,U111787,U114F87)
  • Back Door Closer does not Operate
  • Power Back Door cannot be Operated Using Any Switch
  • Power Back Door does not Operate Using Cabin Switch
  • Power Back Door does not Operate Using Outside Switch
  • Power Back Door Warning System does not Operate
  • Jam Protection Function Activates During Power Back Door Operation
  • Lock Function does not Operate (Close &)
  • Power Back Door cannot be Operated Frequently

Precaution

PRECAUTION

PRECAUTIONS FOR DISCONNECTING CABLE FROM NEGATIVE (-) AUXILIARY BATTERY TERMINAL

NOTICE:

  • After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

    Click here

    HINT:

    When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

    Click here

PRECAUTIONS FOR REMOVAL, INSTALLATION AND REPLACEMENT OF COMPONENTS

(a) After replacing certain components, it may be necessary to update the ECU security key.

Click here

Parts Location

PARTS LOCATION

ILLUSTRATION

*1

BACK DOOR OPENER SWITCH ASSEMBLY

*2

MULTIPLEX NETWORK DOOR ECU

*3

POWER BACK DOOR SENSOR ASSEMBLY RH

*4

POWER BACK DOOR SENSOR ASSEMBLY LH

*5

POWER BACK DOOR UNIT ASSEMBLY RH

*6

POWER BACK DOOR UNIT ASSEMBLY LH

*7

POWER BACK DOOR WARNING BUZZER

*8

BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY

- BACK DOOR LOCK MOTOR

- LATCH SWITCH

- INITIAL SWITCH

- PAWL SWITCH

- BACK DOOR COURTESY SWITCH

*9

POWER BACK DOOR CONTROL SWITCH NO.1

*10

BACK DOOR CONTROL SWITCH

ILLUSTRATION

*1

POWER BACK DOOR CONTROL SWITCH

*2

RADIO AND DISPLAY RECEIVER ASSEMBLY

*3

MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

*4

CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

*5

POWER DISTRIBUTION BOX ASSEMBLY

- ECU-B NO.2 FUSE

- ECU-IGR NO.1 FUSE

- PBD FUSE

*6

DLC3

System Diagram

SYSTEM DIAGRAM

How To Proceed With Troubleshooting

HINT:

  • Use the following procedure to troubleshoot the power back door system.
  • *: Use the GTS.

PROCEDURE

  1. Toyota Prius Vehicle BROUGHT TO WORKSHOP

NEXT
  1. CUSTOMER PROBLEM ANALYSIS

HINT:

  • In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
  • Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
  • The following 5 items are important points for problem analysis:
    *1: Interview the customer about the details of the driving conditions, environment and the malfunction, then check the DTCs after reading and storing the record of behavior.

    What

    Toyota Prius Vehicle model, system name

    When

    Date, time, occurrence frequency, whether the problem occurred recently or has been occurring for a long time

    Where

    Whether the problem occurs at a specific location

    Under what conditions?

    The state of each courtesy switch and door lock position switch, etc. Whether the ignition switch is ON (IG). Whether the ready on, etc.

    How did it happen?

    Problem symptoms*1

NEXT
  1. CHECK PROBLEM SYMPTOM

(a) Check the problem symptom.

NEXT
  1. INSPECT AUXILIARY BATTERY

(a) Measure the auxiliary battery voltage.

Standard Voltage:

11 to 14 V (IG OFF)

HINT:

  • It can be determined if the auxiliary battery is completely drained by operating the horn.
  • If the auxiliary battery voltage is less than 11 V, recharge or replace the auxiliary battery.

(b) While referring to the component layout drawings and wiring diagrams, etc., perform a visual inspection where possible for blown fuses, an open or short in a wire harness or improperly connected connectors.

NEXT
  1. CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*

(a) Use the GTS to check if the CAN communication system is functioning normally.

for HEV Model: Click here

for PHEV Model: Click here

Result

Proceed to

DTC is not output

A

DTC is output

B

B

GO TO CAN COMMUNICATION SYSTEM

for HEV Model: Click here

for PHEV Model: Click here

A
  1. CHECK FOR DTC*

(a) Check for DTCs.

Body Electrical > Back Door > Trouble Codes

Result

Proceed to

DTCs are not output

A

DTCs are output

B

B

GO TO DIAGNOSTIC TROUBLE CODE CHART

A
  1. CHECK Toyota Prius Vehicle CONTROL HISTORY (RoB)*

(a) Using the GTS, check for Vehicle Control History (RoB).

Body Electrical > Back Door > Utility

Toyota Prius Vehicle Control History (RoB)

(b) Make a note of the Vehicle Control History (RoB) output.

Result

Proceed to

Toyota Prius Vehicle Control History (RoB) is not output

A

Vehicle Control History (RoB) is output

B

B

GO TO Toyota Prius Vehicle CONTROL HISTORY (RoB)

A
  1. PROBLEM SYMPTOMS TABLE

(a) Refer to Problem Symptoms Table.

Click here

Result

Proceed to

Fault is not listed in Problem Symptoms Table

A

Fault is listed in Problem Symptoms Table

B

B

ADJUST, REPAIR OR REPLACE IN ACCORDANCE WITH PROBLEM SYMPTOMS TABLE

A
  1. OVERALL ANALYSIS AND TROUBLESHOOTING*

(a) Operation Check

Click here

(b) Data List / Active Test

Click here

(c) Terminals of ECU

Click here

(d) Inspection

NEXT
  1. ADJUST, REPAIR OR REPLACE

Result

Proceed to

  • The negative (-) auxiliary battery terminal has disconnected with the back door open.
  • A power source system fuse has removed and installed or replaced.
  • The multiplex network door ECU has removed and installed or replaced, or the multiplex network door ECU connector has disconnected.

A

  • The negative (-) auxiliary battery terminal has not disconnected with the back door open.
  • A power source system fuse has not removed and installed or replaced.
  • The multiplex network door ECU has not removed and installed or replaced, or the multiplex network door ECU connector has not disconnected.

B

B

GO TO STEP 12

A
  1. INITIALIZE POWER BACK DOOR SYSTEM

(a) Initialize the power back door system.

Click here

NEXT
  1. CONFIRMATION TEST

NEXT

END

Operation Check

OPERATION CHECK

OPERATION CONDITION

NOTICE:

  • This check is possible when the "Power back door" customization setting using the multi-information display in the combination meter assembly is set to "ON".

    Click here

  • Before performing an operation check, check that the power back door system customization is set to its default setting.

    Click here

(a) Conditions necessary for the power back door to open:

  • The back door is unlocked (except wireless one motion function).*
  • The Toyota Prius vehicle speed is 3 km/h or less (only when the ignition switch is turned to ON).
  • The shift lever is in P, the brake pedal is depressed or the parking brake lever is pulled up (this can be determined only when the ignition switch is turned to ON).
  • *: Depending on the customize settings, the back door may not unlock and only the driver door unlocks when the first unlock operation is performed. Check that the customize settings in the table below are set to "Disable", and check that the back door unlocks.

    Tester Display

    Link

    Unlock Key Twice Function

    Wireless Unlock Twice Function

    Entry Unlock Twice Function

    HINT:

    Functions that use the electrical key transmitter sub-assembly cannot be operated when the ignition switch is ON.

CHECK BASIC OPERATION

(a) Check the opening operation.

(1) With the back door fully closed, push the power back door control switch for 0.8 seconds or more and check that the power back door warning buzzer sounds for 0.8 seconds, the hazard warning lights flash twice and the back door starts opening.

(2) With the back door fully closed, push the electrical key transmitter sub-assembly (electrical key) for 0.8 seconds or more and check that the power back door warning buzzer sounds for 0.8 seconds, the hazard warning lights flash twice and the back door starts opening.

(3) With the back door fully closed, push the back door opener switch assembly and check that the power back door warning buzzer sounds for 0.8 seconds, the hazard warning lights flash twice and the back door starts opening.

(b) Check the close operation.

(1) With the back door fully open, push the power back door control switch for 0.8 seconds or more and check that the power back door warning buzzer sounds for 0.8 seconds, the hazard warning lights flash twice and the back door starts closing.

(2) With the back door fully open, push the electrical key transmitter sub-assembly (electrical key) for 0.8 seconds or more and check that the power back door warning buzzer sounds for 0.8 seconds, the hazard warning lights flash twice and the back door starts closing.

(3) With the back door fully open, push the power back door control switch no.1 and check that the power back door warning buzzer sounds for 0.8 seconds, the hazard warning lights flash twice and the back door starts closing.

(4) With the back door fully opened, check that when the back door control switch is briefly pressed, the buzzer sounds for 0.8 seconds, the hazard lights flash twice, and all doors lock after the back door is closed.

CHECK OPERATION WHEN ANOTHER INPUT DETECTED DURING OPEN AND CLOSE OPERATIONS

(a) Check operation when another input detected during open operations

(1) During a power back door opening operation, push the power back door control switch and check that the power back door warning buzzer sound for 0.2 seconds and the back door opening operation stops.

After the opening operation stops, press the power back door control switch again and check that the power back door warning buzzer sounds for 0.8 seconds, the hazard warning lights flash twice and the back door starts closing.

(2) During a power back door opening operation, push the electrical key transmitter sub-assembly (electrical key) and check that the power back door warning buzzer sound for 0.2 seconds and the back door opening operation stops.

After the opening operation stops, push the electrical key transmitter sub-assembly (electrical key) again and check that the power back door warning buzzer sounds for 0.8 seconds, the hazard warning lights flash twice and the back door starts closing.

(3) During a power back door opening operation, push the power back door control switch no.1 and check that the power back door warning buzzer sound for 0.2 seconds and the power back door opening operation stops.

After the opening operation stops, push the power back door control switch no.1 again and check that the power back door warning buzzer sounds for 0.8 seconds, the hazard warning lights flash twice and the back door starts closing.

(4) During a power back door opening operation, push the back door opener switch assembly and check that the power back door warning buzzer sounds for 0.2 seconds and the power back door opening operation stops.

After the opening operation stops, push the back door opener switch assembly again and check that the power back door warning buzzer sounds for 0.8 seconds, the hazard warning lights flash twice and the back door starts closing.

(b) Check operation when another input detected during close operations

(1) During a power back door closing operation, push the power back door control switch and check that the power back door warning buzzer sound for 0.2 seconds and the back door stops.

After the closing operation stops, press the power back door control switch again and check that the power back door warning buzzer sounds for 0.8 seconds, the hazard warning lights flash twice and the back door starts opening.

(2) During a power back door closing operation, push the electrical key transmitter sub-assembly (electrical key) and check that the power back door warning buzzer sound for 0.2 seconds and the back door stops.

After the closing operation stops, press the electrical key transmitter sub-assembly (electrical key) and check that the power back door warning buzzer sounds for 0.8 seconds, the hazard warning lights flash twice and the back door starts opening.

(3) During a power back door closing operation, push the power back door control switch no.1 and check that the power back door warning buzzer sounds for 0.2 seconds and the power back door closing operation stops.

After the closing operation stops, push the power back door control switch no.1 and check that the power back door warning buzzer sounds for 0.8 seconds, the hazard warning lights flash twice and the back door starts opening.

(4) During a power back door closing operation, push the back door opener switch assembly and check that the power back door warning buzzer sounds for 0.2 seconds and the power back door closing operation stops.

After the closing operation stops, push the back door opener switch assembly again and check that the power back door warning buzzer sounds for 0.8 seconds, the hazard warning lights flash twice and the back door starts opening.

CHECK WIRELESS ONE MOTION FUNCTION

NOTICE:

  • This check is possible when the "Wireless Backdoor Open Operation Adjust" customization setting using the GTS is set to other than "Prohibit".
  • This check is possible when the "PBD Wireless Function" customization setting using the GTS is set to "ON".
  • This check is possible when the "PBD Wireless One Motion Function" customization setting using the GTS is set to "ON".

    Click here

(a) Conditions necessary for the power back door to open:

(1) All doors are locked.

(b) Check the wireless one motion operation.

(1) Push the electrical key transmitter sub-assembly (electrical key) and check that the power back door warning buzzer sounds for 0.8 seconds, the hazard warning lights flash twice and the back door starts opening.

CHECK JAM PROTECTION FUNCTION

HINT:

  • The multiplex network door ECU detects changes in the operating speed of the back door while the power back door is operating.
  • When the power back door sensor assemblies built into both sides of the back door are compressed, it is judged that foreign objects are in the path of the power back door and the operation will reverse a certain amount of the opposite direction and then stop.
  • The power back door sensor assemblies operate only while the back door is closing. They do not operate while the back door is opening.

(a) Check the jam protection function (the power back door sensor assembly) while the power back door is closing.

NOTICE:

Do not check this function using a part of your body such as your hand. Also, pay thorough attention that nothing gets caught by accident in this process.

(1) Fully open the back door.

(2) Press a switch to close the power back door.

(3) While the back door is closing, press a power back door sensor assembly using the handle of a hammer or equivalent and check that the buzzer sounds twice for 0.1 seconds and the power back door reverses a certain amount and stops.

(b) Check the jam protection function (the pulse sensor in the multiplex network door ECU) while the power back door is closing.

NOTICE:

Do not check this function using a part of your body such as your hand. Also, pay thorough attention that nothing gets caught by accident in this process.

(1) Fully open the back door.

(2) Press a switch to close the power back door.

(3) While the back door is closing, insert a tire or equivalent between the door panel and Toyota Prius vehicle body, in order to interrupt the closing operation and check that the buzzer sounds twice for 0.1 seconds and the power back door reverses a certain amount and stops.

(c) Check the jam protection function while the power back door is opening.

(1) Fully close the back door.

(2) Press a switch to open the power back door.

(3) While the back door is opening, use your hands to press on the outside surface of the back door panel so that the operating speed decreases and check that the buzzer sounds twice for 0.1 seconds and the power back door stops.

CHECK ASSIST OPERATION

NOTICE:

This check is possible when the "PBD Assist Close Function" customization setting using the GTS is set to "ON".

Click here

(a) Check that the door automatically starts to fully close when the door is manually moved in the closing direction with the back door at rest.

CHECK AUTOMATIC OPENING OPERATION STOPPED POSITION MEMORIZATION FUNCTION (When not using Multi-information display)

(a) Register open operation automatic stopped position in memory

(1) Open the back door by operating each switch.

(2) Operate each switch to stop the open operation when the back door reaches the desired automatic stopped position.

(3) Press and hold the power back door control switch no.1 for 2 seconds or more with the back door at the stopped position, the buzzer sounds 4 times and the system memorizes the automatic stopped position for the open operation.

(4) Check that the back door stops at the memorized position when an open operation is performed with each switch.

(b) Clear open operation automatic stopped position memory

(1) Open the back door by operating each switch.

(2) Stop the back door by operating each switch.

(3) Press and hold the power back door control switch no.1 for 7 seconds or more with the back door at the stopped position, the buzzer sounds 4 times and sounds 2 times and the system clears the automatic stopped position for the open operation.

(4) Operate each switch to start the open operation and check that the back door stops at the default opening position.

CHECK AUTOMATIC OPENING OPERATION STOPPED POSITION MEMORIZATION FUNCTION (When using Multi-information display)

(a) Register open operation automatic stopped position in memory

(1) Using the multi-information display in the combination meter assembly, select the "Opening position" customize setting.

Click here

(2) Check that the back door stops at the position set with the customize function when an open operation is performed with each switch.

(b) Clear open operation automatic stopped position memory

(1) Open the back door by operating each switch.

(2) Stop the back door by operating each switch.

(3) Press and hold the power back door control switch no.1 for 7 seconds or more with the back door at the stopped position, the buzzer sounds 4 times and sounds 2 times and the system clears the automatic stopped position for the open operation.

(4) Operate each switch to start the open operation and check that the back door stops at the default opening position.

CHECK POWER BACK DOOR CLOSE AND LOCK FUNCTION

(a) Check reservation lock function

NOTICE:

This check is possible when the "PBD Walk Away Close & Lock Function" customization setting using the GTS is set to "OFF".

Click here

(1) When the following conditions are met, press the back door control switch while carrying the electrical key transmitter sub-assembly (electrical key), and check that the back door closes and all doors are locked.

  • Ignition switch off
  • Back door is open
  • Door other than the back door is closed
  • Electrical key transmitter sub-assembly (electrical key) is not in the Toyota Prius vehicle

HINT:

If the back door control switch is operated with the hand holding the transmitter switch (electrical key transmitter sub-assembly), it may not operate due to being outside the key detection area.

(b) Check walk away close and lock function

NOTICE:

  • This check is possible when the "PBD Walk Away Close & Lock Function" customization setting using the GTS is set to "ON".

    Click here

  • This function cannot be used with only the digital key.*
  • *: w/ Digital Key

(1) When the following conditions are met, press the back door control switch while carrying the electrical key transmitter sub-assembly (electrical key) to completes reservation, and carrying the electrical key transmitter sub-assembly (electrical key) outside of the detection area and check that the back door closes and all doors are locked.

  • Ignition switch off
  • Back door is open
  • Door other than the back door is closed
  • Electrical key transmitter sub-assembly (electrical key) is not in the Toyota Prius vehicle

HINT:

  • Bringing the electrical key transmitter sub-assembly (electrical key) into the detection area while the back door is closing will stop the operation.
  • If the back door control switch is operated with the hand holding the transmitter switch (electrical key transmitter sub-assembly), it may not operate due to being outside the key detection area.

Customize Parameters

CUSTOMIZE PARAMETERS

CUSTOMIZE POWER BACK DOOR SYSTEM

(a) Customizing with the GTS.

(1) Select the setting by referring to the table below.

PSD & PBD operation

Tester Display

Description

Default

Setting

ECU

Wireless Backdoor Open Operation Adjust

Function that select the switch operation of the power back door button (electrical key transmitter subassembly (electrical key)) to open the back door.

Long1

$00:1tim ON,$01:2tim ON,$02:Long1,$03:Long2,$07:Prohibit

Main body ECU (Multiplex network body ECU)

PBD SW Operating Condition Setting

power back door control switch operation.

Short Press (0.04s) or Long Press (0.8s)

$00:Short Press (0.04s),$01:Long Press (0.8s)

Multiplex network door ECU

PBD Assist Close Function

Function that enables/disables the power back door assist close operation. When set to ON, the back door will close automatically when operated in the close direction manually.

ON

$00:OFF,$01:ON

Multiplex network door ECU

PBD Assist Open Function

Function that enables/disables the power back door assist open operation. When set to ON, the back door will open automatically when the back door opener switch assembly (open switch) is operated.

ON

$00:OFF,$01:ON

Multiplex network door ECU

PBD Door Unlock with One Motion Setting

Function that selects the door or doors to unlock when the back door is locked and the electrical key transmitter subassembly (electrical key) is pushed to operate the power back door.

ALL DOORS

$00:Back Door,$01:All Doors

Multiplex network door ECU

PBD Wireless Function

Function that operates the power back door by pushing the transmitter switch (electrical key transmitter sub-assembly).

ON

$00:OFF,$01:ON

Multiplex network door ECU

PBD Wireless One Motion Function

Wireless one motion function.*1

ON

$00:OFF,$01:ON

Multiplex network door ECU

PBD Wireless SW Setting

Wireless operation setting condition.

1 Time Press, 2 Times Press or Long Press (0.8s)

$00:1 Time Press,$01:2 Times Press,$02:Long Press (0.8s)

Multiplex network door ECU

PBD Walk Away Close & Lock Function

Power back door walk away close and lock function.

ON

$00:OFF,$01:ON

Multiplex network door ECU

  • *1: Enables when the following conditions are met:
    • "Wireless Backdoor Open Operation Adjust" is set to other than "Prohibit"
    • "PBD Wireless Function" is set to "ON"

(b) Customizing with the multi-information display (combination meter assembly)

(1) Turn the ignition switch to ON.

(2) Enter the following menus: Toyota Prius Vehicle Settings / Power Back Door.

Display

Description

Default

Setting

Relevant ECU

Power back door

Function that enables or disables the power back door operation.

ON

ON or OFF

Multiplex network door ECU

Buzzer volume

Function that can be used to set the power back door buzzer volume.

Loud

Loud, Normal or Soft

Multiplex network door ECU

Opening position

Function that can be used to set the power back door opening angle.

5

5, 4, 3, 2, 1 or Manual

Multiplex network door ECU

Problem Symptoms Table

PROBLEM SYMPTOMS TABLE

HINT:

  • Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
  • Inspect the fuses and relays related to this system before inspecting the suspected areas below.
Power Back Door System

Symptom

Suspected Area

Link

Power back door cannot be operated using any switch

Navigation system / Audio and visual system

Check customize setting (power back door function)

Check customize setting (Unlock Key Twice Function "Disable")

Check customize setting (Wireless Unlock Twice Function "Disable")

Check customize setting (Entry Unlock Twice Function "Disable")

Power back door sensor assembly RH

Power back door sensor assembly LH

Harness and connector

Multiplex network door ECU

Power back door does not operate using the cabin switch

Power back door control switch

Harness and connector

Multiplex network door ECU

Main body ECU (multiplex network body ECU)

Power back door does not operate using outside switch

Power back door control switch no.1

Harness and connector

Multiplex network door ECU

Power back door cannot be opened using the back door opener switch assembly (open switch) (back door entry unlock function operates normally)

Multiplex network door ECU

Back door closer does not operate

Back door visual check (foreign objects)

Back door lock with courtesy light switch assembly

Harness and connector

Multiplex network door ECU

Close and lock function does not operate

Back door control switch

Harness and connector

Multiplex network door ECU

Jam protection function activates during power back door operation

Back door visual check (foreign objects)

Power back door sensor assembly RH

Power back door sensor assembly LH

Harness and connector

Multiplex network door ECU

Power back door warning system does not operate

Wireless door lock control system

Harness and connector

Power back door warning buzzer

Multiplex network door ECU

Power back door cannot be operated frequently

Refer to "Power Back Door cannot be Operated Frequently".

Terminals Of Ecu

TERMINALS OF ECU

CHECK MULTIPLEX NETWORK DOOR ECU

(a) Disconnect the W16, W17 and W13 multiplex network door ECU connectors.

(b) Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

W13-9 (IG) - Body ground

IG power supply

Ignition switch ON

11 to 14 V

Ignition switch off

Below 1 V

W13-7 (ECUB) - Body ground

Auxiliary battery power supply

Ignition switch off

11 to 14 V

W16-5 (B) - Body ground

Auxiliary battery power supply

Ignition switch off

11 to 14 V

W17-4 (GND) - Body ground

Body ground

Always

Below 1 Ω

(c) Reconnect the W13, W14 and W17 multiplex network door ECU connectors.

(d) Measure the voltage and waveform according to the value(s) in the table below.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

W17-2 (DC ) - W17-6 (DC-)

Back door lock assembly (back door lock motor) circuit

Back door lock motor operating

11 to 14 V

Back door lock motor not operating

Below 1 V

W14-1 (OSL) - W14-9 (OSE)

Power back door sensor assembly LH signal

Power back door sensor assembly LH not pressed

2 to 3 V

Power back door sensor assembly LH pressed

Below 1 V

W14-3 (DSV2) - Body ground

Power back door unit assembly RH (door sensor) power supply

Always

7 V or higher

W14-4 (DSV) - Body ground

Power back door unit assembly LH (door sensor) power supply

Always

7 V or higher

W14-5 (DS2) - Body ground

Power back door unit assembly LH (door sensor) signal

Power back door not operating

0 V or 7 V or higher

Power back door operating

Pulse generation

(See waveform 2)

W14-6 (DS12) - Body ground

Power back door unit assembly RH (door sensor) signal

Power back door not operating

0 V or 7 V or higher

Power back door operating

Pulse generation

(See waveform 1)

W14-8 (OSR) - W14-9 (OSE)

Power back door sensor assembly RH signal

Power back door sensor assembly RH not pressed

2 to 3 V

Power back door sensor assembly RH pressed

Below 1 V

W14-10 (DSG2) - Body ground

Power back door unit assembly RH (door sensor) ground

Always

Below 1 V

W14-11 (DSG) - Body ground

Power back door unit assembly LH (door sensor) ground

Always

Below 1 V

W14-12 (DS22) - Body ground

Power back door unit assembly RH (door sensor) signal

Power back door not operating

0 V or 7 V or higher

Power back door operating

Pulse generation

(See waveform 2)

W14-13 (DS1) - Body ground

Power back door unit assembly LH (door sensor) signal

Power back door not operating

0 V or 7 V or higher

Power back door operating

Pulse generation

(See waveform 1)

W13-1 (BZR ) - Body ground

Power back door warning buzzer signal

Power back door warning buzzer sounding

Pulse generation

Power back door warning buzzer not sounding

Below 1 V

W13-3(FUL) - Body ground

Back door lock with courtesy light switch assembly input

Back door open

Below 1 V

Back door closed

Pulse generation

W13-4 (CLSW) - Body ground

Back door control switch signal

Back door control switch on

Below 1 V

Back door control switch off

11 to 14 V

W13-5(HAF) - Body ground

Back door lock with courtesy light switch assembly lock signal

Back door closed

11 to 14 V

Back door fully open

Below 1 V

W13-11(LIB) - Body ground

Back door lock with courtesy light switch assembly lock signal

Back door is locked

11 to 14 V

Back door is unlocked

Below 1 V

W13-13(PAWL) - Body ground

Back door lock with courtesy light switch assembly lock signal

Back door fully open

11 to 14 V

Back door ajar

Below 1 V

Back door closed

11 to 14 V

A certain amount of time after back door closed

Below 1 V

W13-14 (BDDN) - Body ground

Power back door control switch no.1 signal

Power back door control switch no.1 on

Below 1 V

Power back door control switch no.1 off

Pulse generation

W13-15(POS) - Body ground

Back door lock with courtesy light switch assembly signal

Back door open

Below 1 V

Back door closer operating

11 to 14 V

Operation complete

Below 1 V

(1) Using an oscilloscope, check waveform 1.

Waveform 1 (Reference)

Item

Condition

Tester Connection

  • W14-13 (DS1) - Body ground
  • W14-6 (DS12) - Body ground

Tool Setting

2 V/DIV., 2 ms./DIV.

Toyota Prius Vehicle Condition

Power back door operating

HINT:

  • The period changes in accordance to the speed at which the power back door is opened and closed.
  • The wave height changes in accordance with the auxiliary battery voltage.

(2) Using an oscilloscope, check waveform 2.

Waveform 2 (Reference)

Item

Condition

Tester Connection

  • W14-5 (DS2) - Body ground
  • W14-12 (DS22) - Body ground

Tool Setting

2 V/DIV., 2 ms./DIV.

Toyota Prius Vehicle Condition

Power back door operating

HINT:

  • The period changes in accordance to the speed at which the power back door is opened and closed.
  • The wave height changes in accordance with the auxiliary battery voltage.

CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

Click here

CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND POWER DISTRIBUTION BOX ASSEMBLY

NOTICE:

When disconnecting a wire harness of any component connected to the supply power of the integrated capacitor (integration control supply) or when removing the integrated capacitor (integration control supply), make sure to wait 5 minutes or more after turning the ignition switch off for self-diagnosis to complete and the voltage of the integrated capacitor (integration control supply) to discharge.

(a) Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.

Click here

(b) Connect the power distribution box assembly connectors.

(c) Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

z1-13 (GND1) - Body ground

Body ground

Always

Below 1 Ω

z1-14 (GND2) - Body ground

Body ground

Always

Below 1 Ω

z1-26 (BECU) - Body ground

Auxiliary battery power supply

Ignition switch off

11 to 14 V

z1-27 (IGR) - Body ground

IG power supply

Ignition switch ON

11 to 14 V

Ignition switch off

Below 1 V

(d) Install the main body ECU (multiplex network body ECU).

Click here

(e) Measure the voltage and waveform according to the value(s) in the table below.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

K15-7 (LSBO) - Body ground

Back door lock signal

Back door is locked

11 to 14 V

Back door is unlocked

Below 1 V

K16-21 (PBDS) - Body ground

Power back door control switch signal

Power back door control switch off

Pulse generation

Power back door control switch on

Below 1 V

R17-2 (BCTY) - Body ground

Back door courtesy light switch input

Back door closed

11 to 14 V or pulse output (maximum 14 V)*

Back door open

Below 1 V

  • *: Differs depending on the Toyota Prius vehicle model

Freeze Frame Data

FREEZE FRAME DATA

CHECK FREEZE FRAME DATA

HINT:

Whenever a DTC is detected, the multiplex network door ECU stores the current vehicle state as Freeze Frame Data.

(a) Enter the following menus: Body Electrical / Back Door / Trouble Codes.

Body Electrical > Back Door > Trouble Codes

(b) Select a DTC to display its freeze frame data.

FREEZE FRAME DATA

Body Electrical > Back Door

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Total Distance Traveled

Total distance traveled

0 to 16777215

Same as actual total distance traveled

For the unit, refer to "Total Distance Traveled - Unit"

Total Distance Traveled - Unit

Total Distance Traveled - unit

km or mile

km: km

mile: mile

-

Data List / Active Test

DATA LIST / ACTIVE TEST

DATA LIST

HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

(a) According to the display on the GTS, read the Data List.

Body Electrical > Back Door > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Total Distance Traveled

Total distance traveled

0 to 16777215

Same as actual total distance traveled

For the unit, refer to "Total Distance Traveled - Unit"

Total Distance Traveled - Unit

Total Distance Traveled - unit

km or mile

km: km

mile: mile

-

PBD Walk Away Close & Lock Function

Status of the walk away close and lock function

ON or OFF

Current customize setting displayed

-

Back Door Lock Status

Back door condition signal

Lock or Unlock

Lock: Back door locked

Unlock: Back door unlocked

-

Half Latch Switch

Latch switch signal

ON or OFF

ON: When in the open latch or overstroke position

OFF: Half latch position → full latch position

-

Closer Position Switch

Initial switch signal

ON or OFF

ON: Back door lock sector gear in center position (Initial switch on)

OFF: Back door lock sector gear out of center position (Initial switch off)

-

Pawl Switch

Pawl switch signal

ON or OFF

ON: Back door lock motor open-latched

OFF: Back door lock motor except open latched

-

Courtesy Switch

Back door courtesy switch signal

ON or OFF

ON: Open latch position → half latch position

OFF: Full latch position → overstroke position

-

PBD Main Switch

Power back door ON/OFF signal

ON or OFF

Current customize setting displayed

-

PBD Close Switch

Power back door control switch no.1 signal

ON or OFF

ON: Power back door control switch no.1 pushed

OFF: Power back door control switch no.1 not pushed

-

IG Switch

Ignition switch signal

ON or OFF

ON: Ignition switch ON

OFF: Ignition switch off

"OFF" is also displayed for this item when the ignition switch to ACC.

Close and Lock Switch

Door control switch signal

ON or OFF

ON: Door control switch pressed

OFF: Door control switch not pressed

-

Door Lock Signal

Back door condition signal

Lock or Unlock

Lock: Back door locked

Unlock: Back door unlocked

-

PBD Touch Sensor RH

Power back door sensor assembly RH signal

ON, OFF or Open

ON: Power back door sensor assembly RH pressed

OFF: Power back door sensor assembly RH not pressed

Open: Power back door sensor assembly RH circuit open

-

PBD Touch Sensor LH

Power back door sensor assembly LH signal

ON, OFF or Open

ON: Power back door sensor assembly LH pressed

OFF: Power back door sensor assembly LH not pressed

Open: Power back door sensor assembly LH circuit open

-

Correction of Back Door Position

Correction of back door position

Not Complied With or Complied With

Not Complied With: not complied with

Complied With: complied with

-

PBD Close Switch Operation History

Power back door control switch no.1 operation history

ON or OFF

ON: Has operation history

OFF: No operation history

The operation history will be cleared by disconnecting the cable from the negative (-) terminal of the auxiliary battery for approximately 30 seconds.

Close & Lock Switch Operation History

Back door control switch operation history

ON or OFF

ON: Has operation history

OFF: No operation history

The operation history will be cleared by disconnecting the cable from the negative (-) terminal of the auxiliary battery for approximately 30 seconds.

Opened Number of Times

Number of times for back door opened

0 to 2147483647

Number of times for back door opened

-

Closed Number of Times

Number of times for back door closed

0 to 2147483647

Number of times for back door closed

-

During Open Operation Number of Stoppages

Number of times the back door stopped during an open operation

0 to 65535

Number of times the back door stopped during an open operation

-

During Close Operation Number of Stoppages

Number of times the back door stopped during a close operation

0 to 65535

Number of times the back door stopped during a close operation

-

Opening Adjustment Number of Times by Display Inside the Car

Number of times the back door opening angle adjustment was changed via the multi-information display

0 to 65535

Number of times the back door opening angle adjustment was changed

-

Opening Adjustment Number of Times by Back Door Switch

Number of times the back door opening angle adjustment was changed by pressing and holding the switch at the bottom of the back door

0 to 65535

Number of times the open operation automatic stop position was changed

-

Door Opening Setting Position

Current set value of the open operation automatic stop position (target home position after auto operation)

0 to 65535

Current set value

-

PBD SW Operating Condition Setting

Power back door control switch operation

Short Press (0.04s) or Long Press (0.8s)

Current customize setting displayed

-

PBD Buzzer Function

Status of the power back door buzzer

ON or OFF

Current customize setting displayed

-

PBD Assist Close Function

Function that enables/disables the power back door assist close operation. When set to ON, the back door will close automatically when operated in the close direction manually.

ON or OFF

Current customize setting displayed

-

PBD Assist Open Function

Function that enables/disables the power back door assist open operation. When set to ON, the back door will open automatically when the back door opener switch assembly (open switch) is operated.

ON or OFF

Current customize setting displayed

-

PBD Door Unlock with One Motion Setting

Door or doors to be unlocked when back door locked and power back door operated by pressing transmitter switch (electrical key transmitter sub-assembly).

Back Door or All Doors

Current customize setting displayed

-

PBD Wireless Function

Function that operates the power back door by pushing the transmitter switch (electrical key transmitter sub-assembly).

ON or OFF

Current customize setting displayed

-

PBD Wireless One Motion Function

Wireless one motion function

ON or OFF

Current customize setting displayed

-

PBD Wireless SW Setting

Wireless operationsetting condition

1 Time Press, 2Times Press or LongPress (0.8s)

Current customizesetting displayed

-

Body Electrical > Main Body > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Back Door Lock Position Status

Back door lock position signal

Lock or Unlock

Lock: Back door locked

Unlock: Back door unlocked

-

Back Door Operation Switch (Instrument)

Power back door control switch signal

ON or OFF

ON: Power back door control switch on

OFF: Power back door control switch off

-

ACTIVE TEST

HINT:

Using the GTS, perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) According to the display on GTS perform the "Active Test".

Body Electrical > Back Door > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

PBD Motor (Open)

Power back door motor operation

Start

-

PBD Motor (Close)

Power back door motor operation

Start

-

PBD Buzzer (Small Volume)

Power back door warning buzzer sound (small volume)

Start

-

PBD Buzzer (Middle Volume)

Power back door warning buzzer sound (Middle volume)

Start

-

PBD Buzzer (Large Volume)

Power back door warning buzzer sound (Large volume)

Start

-

PBD Release Closer

Latch release operation

Start

-

Courtesy Lamp

Back door courtesy light operation

Start

-

VEHICLE CONTROL HISTORY (RoB)

VEHICLE CONTROL HISTORY (RoB)

NOTICE:

  • If the vehicle or vehicle controls are operated (for example, during initial inspection when the vehicle is brought in for repair) before vehicle control history (RoB) has been read out and saved, the vehicle control history (RoB) information could be lost.
  • The function "Read Toyota Prius vehicle control history (RoB)" uses the current system time setting inside the GTS and the time counter inside the controlling ECU to calculate the timings shown in the vehicle control history (RoB). For this reason, before reading out the vehicle control history (RoB), first make sure that the GTS system clock is accurately set to the current time.
  • The time counter in the control ECU may deviate by up to /- 10% due to the characteristics of the time counter.
  • The time counter in the control ECU is reset approximately 34 days before the "Current" value due to the characteristics of the time counter. Therefore, the time information stored before the 34th day may not be accurately displayed.

Toyota Prius Vehicle CONTROL HISTORY (RoB)

(a) Check vehicle control history (RoB) according to the display on the GTS.

Body Electrical > Back Door > Utility

Toyota Prius Vehicle Control History (RoB)

RoB Code

RoB Item

Item description

X283E

Back Door Operation History

Memorize the factors when the power back door operated

X2903

Back Door Non-Operation History

Memorize the factors when the power back door non-operation

Body Electrical > Main Body > Utility

Toyota Prius Vehicle Control History (RoB)

RoB Code

RoB Item

Item description

X2303

Trunk/Back Door

Memorize the factors when the power back door operated

HINT:

Toyota Prius Vehicle Control History (RoB): The main body ECU (multiplex network body ECU) records the power back door system vehicle control history (RoB), which can be read out using the GTS.

CLEAR VEHICLE CONTROL HISTORY (RoB)

NOTICE:

Performing following procedure will delete all vehicle control history (RoB) records.

(a) Clear Toyota Prius vehicle control history (RoB) according to the display on the GTS.

Body Electrical > Back Door > Utility

Vehicle Control History (RoB)

Body Electrical > Main Body > Utility

Toyota Prius Vehicle Control History (RoB)

Back Door Motor Internal Electronic Failure (B222049)

DESCRIPTION

This DTC is stored when the multiplex network door ECU detects a malfunction of the motor built-into the power back door unit assembly LH or power back door unit assembly RH.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

DTC Output from

Priority

B222049

Back Door Motor Internal Electronic Failure

Malfunction of motor built into the power back door unit assembly LH or power back door unit assembly RH detected

  • Multiplex network door ECU
  • Power back door unit assembly LH
  • Power back door unit assembly RH
  • Harness or connector

Back Door

A

WIRING DIAGRAM

NOTICE:

If the multiplex network door ECU has been replaced, or if any of the connectors has been disconnected, initialize the power back door system.

Click here

PROCEDURE

  1. CLEAR DTC

(a) Clear the DTCs.

Body Electrical > Back Door > Clear DTCs
NEXT
  1. REPRODUCE DTC

(a) Perform a power back door open or close operation.

NEXT
  1. CHECK FOR DTC

(a) Check for DTCs.

Body Electrical > Back Door > Trouble Codes

Result

Proceed to

B222049 is output

A

B222049 is not output

B

B

USE SIMULATION METHOD TO CHECK

A
  1. INSPECT POWER BACK DOOR UNIT ASSEMBLY LH

Pre-procedure1

(a) Fully open the back door.

(b) Disconnect the W5 power back door unit assembly LH connector.

*a

Component without harness connected

(Power Back Door Unit Assembly LH)

Procedure1

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(W5) Click Connector(W5)

Tester Connection

Condition

Specified Condition

Result

W5-1 (BD ) - Body ground

Always

10 kΩ or higher

kΩ

W5-2 (BD-) - Body ground

Always

10 kΩ or higher

kΩ

W5-1 (BD ) - W5-2 (BD-)

Always

Below 1 MΩ

MΩ

Post-procedure1

(d) None

NG

REPLACE POWER BACK DOOR UNIT ASSEMBLY LH

OK
  1. INSPECT POWER BACK DOOR UNIT ASSEMBLY RH

Pre-procedure1

(a) Fully open the back door.

(b) Disconnect the W4 power back door unit assembly RH connector.

*a

Component without harness connected

(Power Back Door Unit Assembly RH)

Procedure1

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(W4) Click Connector(W4)

Tester Connection

Condition

Specified Condition

Result

W4-1 (BD 2) - Body ground

Always

10 kΩ or higher

kΩ

W4-2 (BD-2) - Body ground

Always

10 kΩ or higher

kΩ

W4-1 (BD 2) - W4-2 (BD-2)

Always

Below 1 MΩ

MΩ

Post-procedure1

(d) None

NG

REPLACE POWER BACK DOOR UNIT ASSEMBLY RH

OK
  1. CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - POWER BACK DOOR UNIT ASSEMBLY LH)

Pre-procedure1

(a) Disconnect the W16 multiplex network door ECU connector.

(b) Disconnect the W5 power back door unit assembly LH connector.

Procedure1

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(W16,W5) Click Connector(W16) Click Connector(W5)

Tester Connection

Condition

Specified Condition

Result

W16-1 (BD ) - W5-1 (BD )

Always

Below 1 Ω

Ω

W16-3 (BD-) - W5-2 (BD-)

Always

Below 1 Ω

Ω

W16-1 (BD ) or W5-1 (BD ) - Body ground

Always

10 kΩ or higher

kΩ

W16-3 (BD-) or W5-2 (BD-) - Body ground

Always

10 kΩ or higher

kΩ

Post-procedure1

(d) None

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - POWER BACK DOOR UNIT ASSEMBLY RH)

Pre-procedure1

(a) Disconnect the W16 multiplex network door ECU connector.

(b) Disconnect the W4 power back door unit assembly RH connector.

Procedure1

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(W16,W4) Click Connector(W16) Click Connector(W4)

Tester Connection

Condition

Specified Condition

Result

W16-6 (BD 2) - W4-1 (BD 2)

Always

Below 1 Ω

Ω

W16-8 (BD-2) - W4-2 (BD-2)

Always

Below 1 Ω

Ω

W16-6 (BD 2) or W4-1 (BD 2) - Body ground

Always

10 kΩ or higher

kΩ

W16-8 (BD-2) or W4-2 (BD-2) - Body ground

Always

10 kΩ or higher

kΩ

Post-procedure1

(d) None

OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

PBD Unit Pulse Sensor LH Circuit No Signal (B222631)

DESCRIPTION

This DTC is output when the multiplex network door ECU detects a power back door unit assembly LH pulse malfunction.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

DTC Output from

Priority

B222631

PBD Unit Pulse Sensor LH Circuit No Signal

Multiplex network door ECU detects power back door unit assembly LH pulse malfunction

  • Multiplex network door ECU
  • Power back door unit assembly LH
  • Harness or connector

Back Door

A

WIRING DIAGRAM

NOTICE:

If the multiplex network door ECU has been replaced, or if any of the connectors has been disconnected, initialize the power back door system.

Click here

PROCEDURE

  1. CLEAR DTC

(a) Clear the DTCs.

Body Electrical > Back Door > Clear DTCs
NEXT
  1. REPRODUCE DTC

(a) Perform a power back door open or close operation.

NEXT
  1. CHECK FOR DTC

(a) Check for DTCs.

Body Electrical > Back Door > Trouble Codes

Result

Proceed to

B222631 is output

A

B222631 is not output

B

B

USE SIMULATION METHOD TO CHECK

A
  1. CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - POWER BACK DOOR UNIT ASSEMBLY LH)

Pre-procedure1

(a) Disconnect the W14 multiplex network door ECU connector.

(b) Disconnect the W5 power back door unit assembly LH connector.

Procedure1

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(W14,W5) Click Connector(W14) Click Connector(W5)

Tester Connection

Condition

Specified Condition

Result

W14-11 (DSG) - W5-4 (DSG)

Always

Below 1 Ω

Ω

W14-4 (DSV) - W5-3 (DSV)

Always

Below 1 Ω

Ω

W14-5 (DS2) - W5-6 (DS2)

Always

Below 1 Ω

Ω

W14-13 (DS1) - W5-5 (DS1)

Always

Below 1 Ω

Ω

W14-11 (DSG) or W5-4 (DSG) - Body ground

Always

10 kΩ or higher

kΩ

W14-4 (DSV) or W5-3 (DSV) - Body ground

Always

10 kΩ or higher

kΩ

W14-5 (DS2) or W5-6 (DS2) - Body ground

Always

10 kΩ or higher

kΩ

W14-13 (DS1) or W5-5 (DS1) - Body ground

Always

10 kΩ or higher

kΩ

Post-procedure1

(d) None

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK MULTIPLEX NETWORK DOOR ECU

Pre-procedure1

(a) Disconnect the W5 power back door unit assembly LH connector.

Procedure1

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(W5) Click Connector(W5)

Tester Connection

Condition

Specified Condition

Result

W5-4 (DSG) - Body ground

Always

Below 1 Ω

Ω

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Click Location & Routing(W5) Click Connector(W5)

Tester Connection

Condition

Specified Condition

Result

W5-5 (DS1) - Body ground

Ignition switch off

7 V or higher

V

W5-6 (DS2) - Body ground

Ignition switch off

7 V or higher

V

W5-3 (DSV) - Body ground

Ignition switch off

7 V or higher

V

Post-procedure1

(d) None

NG

REPLACE MULTIPLEX NETWORK DOOR ECU

OK
  1. CHECK POWER BACK DOOR UNIT ASSEMBLY LH

(a) Using an oscilloscope, check the waveform of each terminal from the rear of the multiplex network door ECU connector.

*a

Component with harness connected

(Multiplex Network Door ECU)

*b

Waveform (CH1)

*c

Waveform (CH2)

-

-

Measurement Condition:

Item

Condition

Tester Connection

  • CH1: W14-13 (DS1) - Body ground
  • CH2: W14-5 (DS2) - Body ground

Tool Setting

2 V/DIV., 2 ms./DIV.

Toyota Prius Vehicle Condition

Open and close the back door by hand.

HINT:

  • The period changes in accordance to the speed at which the back door is opened and closed by hand.
  • The wave height changes in accordance with the auxiliary battery voltage.
OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPLACE POWER BACK DOOR UNIT ASSEMBLY LH

PBD Touch Sensor LH Circuit Circuit Open (B222A13)

DESCRIPTION

This DTC is output when the multiplex network door ECU detects a power back door sensor assembly LH malfunction.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

DTC Output from

Priority

B222A13

PBD Touch Sensor LH Circuit Circuit Open

Multiplex network door ECU detects power back door sensor assembly LH touch sensor malfunction

  • Multiplex network door ECU
  • Power back door sensor assembly LH
  • Harness or connector

Back Door

A

WIRING DIAGRAM

NOTICE:

If the multiplex network door ECU has been replaced, or if any of the connectors has been disconnected, initialize the power back door system.

Click here

PROCEDURE

  1. CLEAR DTC

(a) Clear the DTCs.

Body Electrical > Back Door > Clear DTCs
NEXT
  1. REPRODUCE DTC

(a) Perform a power back door close operation.

NEXT
  1. CHECK FOR DTC

(a) Check for DTCs.

Body Electrical > Back Door > Trouble Codes

Result

Proceed to

B222A13 is output

A

B222A13 is not output

B

B

USE SIMULATION METHOD TO CHECK

A
  1. READ VALUE USING GTS

(a) Read the Data List according to the display on the GTS.

Body Electrical > Back Door > Data List

Tester Display

Measurement Item

Range

Reference Value

Diagnostic Note

PBD Touch Sensor LH

Power back door sensor assembly LH signal

ON, OFF or Open

Open: Power back door sensor assembly LH circuit open

-

Body Electrical > Back Door > Data List

PBD Touch Sensor LH

Result

Proceed to

The value of PBD Touch Sensor LH is Open

A

None of the above conditions are met

B

B

GO TO STEP 7

A
  1. INSPECT POWER BACK DOOR SENSOR ASSEMBLY LH

Click here

NG

REPLACE POWER BACK DOOR SENSOR ASSEMBLY LH

OK
  1. CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - POWER BACK DOOR SENSOR ASSEMBLY LH)

Pre-procedure1

(a) Disconnect the W14 multiplex network door ECU connector.

(b) Disconnect the W7 power back door sensor assembly LH connector.

Procedure1

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(W14,W7) Click Connector(W14) Click Connector(W7)

Tester Connection

Condition

Specified Condition

Result

W14-1 (OSL) - W7-1 (OSL)

Always

Below 1 Ω

Ω

W14-9 (OSE) - W7-2 (OSLE)

Always

Below 1 Ω

Ω

W14-1 (OSL) or W7-1 (OSL) - Body ground

Always

10 kΩ or higher

kΩ

W14-9 (OSE) or W7-2 (OSLE) - Body ground

Always

10 kΩ or higher

kΩ

Post-procedure1

(d) None

OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. READ VALUE USING GTS

(a) Read the Data List according to the display on the GTS.

Body Electrical > Back Door > Data List

Tester Display

Measurement Item

Range

Reference Value

Diagnostic Note

PBD Touch Sensor LH

Power back door sensor assembly LH signal

ON, OFF or Open

OFF: Power back door sensor assembly LH not pressed

-

Body Electrical > Back Door > Data List

PBD Touch Sensor LH

Result

Proceed to

The value of PBD Touch Sensor LH is OFF

A

None of the above conditions are met

B

B

GO TO STEP 5

A
  1. READ VALUE USING GTS

(a) Read the Data List according to the display on the GTS.

Body Electrical > Back Door > Data List

Tester Display

Measurement Item

Range

Reference Value

Diagnostic Note

PBD Touch Sensor LH

Power back door sensor assembly LH signal

ON, OFF or Open

ON: Power back door sensor assembly LH pressed

-

Body Electrical > Back Door > Data List

PBD Touch Sensor LH

Result

Proceed to

The value of PBD Touch Sensor LH is ON

A

None of the above conditions are met

B

A

REPLACE MULTIPLEX NETWORK DOOR ECU

B

GO TO STEP 5

Back Door Closer General Electrical Failure (B225001)

DESCRIPTION

The back door closer is controlled by the multiplex network door ECU.

The multiplex network door ECU determines the latch position of the back door lock assembly with curtesy switch based on the combination of signals from the latch switch built into the back door lock assembly with curtesy switch, back door courtesy switch, initial switch and pawl switch.

This DTC is stored when the back door closer is operating and the initial switch signal indicates that the latch is not in the correct position within the specified amount of time.

When this DTC is output, the multiplex network door ECU suspends back door closer control and power back door control.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

DTC Output from

Priority

B225001

Back Door Closer General Electrical Failure

While the back door closer is operating, a malfunction is detected in position information from the initial switch within a specified amount of time.

  • Back door lock with courtesy light switch assembly
  • Harness or connector
  • Multiplex network door ECU

Back Door

A

WIRING DIAGRAM

NOTICE:

If the multiplex network door ECU has been replaced, or if any of the connectors has been disconnected, initialize the power back door system.

Click here

PROCEDURE

  1. READ VALUE USING GTS

(a) Read the Data List according to the display on the GTS.

Body Electrical > Back Door > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Closer Position Switch

Initial switch signal

ON or OFF

OFF: Back door lock sector gear out of center position (Initial switch off)

-

Body Electrical > Back Door > Data List

Closer Position Switch

Result

Proceed to

The value of Closer Position Switch is OFF

A

None of the above conditions are met

B

B

GO TO STEP 3

A
  1. READ VALUE USING GTS

(a) Read the Data List according to the display on the GTS.

Body Electrical > Back Door > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Closer Position Switch

Initial switch signal

ON or OFF

ON: Back door lock sector gear in center position (Initial switch on)

-

Body Electrical > Back Door > Data List

Closer Position Switch

Result

Proceed to

The value of Closer Position Switch is ON

A

None of the above conditions are met

B

A

REPLACE MULTIPLEX NETWORK DOOR ECU

B
  1. INSPECT BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY

Click here

NG

REPLACE BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY

OK
  1. CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY - MULTIPLEX NETWORK DOOR ECU AND BODY GROUND)

Pre-procedure1

(a) Disconnect the W8 back door lock with courtesy light switch assembly connector.

(b) Disconnect the W13 multiplex network door ECU connector.

Procedure1

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(W8,W13) Click Connector(W8) Click Connector(W13)

Tester Connection

Condition

Specified Condition

Result

W8-6 (OPN) - W13-15 (POS)

Always

Below 1 Ω

Ω

W8-1 (E) - Body ground

Always

Below 1 Ω

Ω

W8-6 (OPN) or W13-15 (POS) - Body ground

Always

10 kΩ or higher

kΩ

Post-procedure1

(d) None

OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

Back Door Closer Switch General Electrical Failure (B225101)

DESCRIPTION

The back door closer is controlled by the multiplex network door ECU.

The multiplex network door ECU determines the latch position of the back door lock assembly with courtesy switch based on the combination of signals from the latch switch built into the back door lock assembly with courtesy switch, back door courtesy switch, initial switch and pawl switch.

This DTC is stored when the back door closer control is being performed and it stops due to the pawl switch or door courtesy switch signal being stuck ON.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

DTC Output from

Priority

B225101

Back Door Closer Switch General Electrical Failure

During a back door closer close operation, it is detected that the pawl switch or back door courtesy switch is stuck ON.

  • Back door lock with courtesy light switch assembly
  • Harness or connector
  • Multiplex network door ECU

Back Door

A

WIRING DIAGRAM

NOTICE:

If the multiplex network door ECU has been replaced, or if any of the connectors has been disconnected, initialize the power back door system.

Click here

PROCEDURE

  1. READ VALUE USING GTS

(a) Read the Data List according to the display on the GTS.

Body Electrical > Back Door > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Half Latch Switch

Latch switch signal

ON or OFF

OFF: Half latch position → full latch position

-

Body Electrical > Back Door > Data List

Half Latch Switch

Result

Proceed to

The value of Half Latch Switch is OFF

A

None of the above conditions are met

B

B

GO TO STEP 7

A
  1. READ VALUE USING GTS

(a) Read the Data List according to the display on the GTS.

Body Electrical > Back Door > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Half Latch Switch

Latch switch signal

ON or OFF

ON: When in the open latch or overstroke position

-

Body Electrical > Back Door > Data List

Half Latch Switch

Result

Proceed to

The value of Half Latch Switch is ON

A

None of the above conditions are met

B

B

GO TO STEP 7

A
  1. READ VALUE USING GTS

(a) Read the Data List according to the display on the GTS.

Body Electrical > Back Door > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Pawl Switch

Pawl switch signal

ON or OFF

OFF: Back door lock motor except open latched

-

Body Electrical > Back Door > Data List

Pawl Switch

Result

Proceed to

The value of Pawl Switch is OFF

A

None of the above conditions are met

B

B

GO TO STEP 7

A
  1. READ VALUE USING GTS

(a) Read the Data List according to the display on the GTS.

Body Electrical > Back Door > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Pawl Switch

Pawl switch signal

ON or OFF

ON: Back door lock motor open-latched

-

Body Electrical > Back Door > Data List

Pawl Switch

Result

Proceed to

The value of Pawl Switch is ON

A

None of the above conditions are met

B

B

GO TO STEP 7

A
  1. READ VALUE USING GTS

(a) Read the Data List according to the display on the GTS.

Body Electrical > Back Door > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Courtesy Switch

Back door courtesy switch signal

ON or OFF

OFF: Full latch position → overstroke position

-

Body Electrical > Back Door > Data List

Courtesy Switch

Result

Proceed to

The value of Courtesy Switch is OFF

A

None of the above conditions are met

B

B

GO TO STEP 7

A
  1. READ VALUE USING GTS

(a) Read the Data List according to the display on the GTS.

Body Electrical > Back Door > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Courtesy Switch

Back door courtesy switch signal

ON or OFF

ON: Open latch position → half latch position

-

Body Electrical > Back Door > Data List

Courtesy Switch

Result

Proceed to

The value of Courtesy Switch is ON

A

None of the above conditions are met

B

A

REPLACE MULTIPLEX NETWORK DOOR ECU

B
  1. INSPECT BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY

HINT:

Click here

NG

REPLACE BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY

OK
  1. CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY - MULTIPLEX NETWORK DOOR ECU AND BODY GROUND)

Pre-procedure1

(a) Disconnect the W8 back door lock with courtesy light switch assembly connector.

(b) Disconnect the W13 multiplex network door ECU connector.

Procedure1

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(W8,W13) Click Connector(W8) Click Connector(W13)

Tester Connection

Condition

Specified Condition

Result

W8-3 (CLS) - W13-5 (HAF)

Always

Below 1 Ω

Ω

W8-2(FSW) - W13-13(PAWL)

Always

Below 1 Ω

Ω

W8-4 (CTY) - W13-3 (FUL)

Always

Below 1 Ω

Ω

W8-1 (E) - Body ground

Always

Below 1 Ω

Ω

W8-3 (CLS) or W13-5 (HAF) - Body ground

Always

10 kΩ or higher

kΩ

W8-2(FSW) or W13-13(PAWL) - Body ground

Always

10 kΩ or higher

kΩ

W8-4 (CTY) or W13-3 (FUL) - Body ground

Always

10 kΩ or higher

kΩ

Post-procedure1

(d) None

OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

Lost Communication with ECM/PCM "A" Missing Message (U010087,U010187,U012987,U014087,U015587,U016387,U016887,U111787,U114F87)

DESCRIPTION

These DTCs are stored when a malfunction occurs in the CAN communication circuit.

DTC No.

Detection Item

Trouble Area

DTC Output from

Priority

U010087

Lost Communication with ECM/PCM "A" Missing Message

  • CAN communication system
  • ECM
  • Multiplex network door ECU

Back Door

B

U010187

Lost Communication with TCM Missing Message

  • CAN communication system
  • Hybrid Toyota Prius vehicle control ECU
  • Multiplex network door ECU

Back Door

B

U012987

Lost Communication with Brake System Control Module Missing Message

  • CAN communication system
  • No. 2 skid control ECU (brake actuator assembly)
  • Multiplex network door ECU

Back Door

B

U014087

Lost Communication with Body Control Module Missing Message

  • CAN communication system
  • Main body ECU (multiplex network body ECU)
  • Multiplex network door ECU

Back Door

B

U015587

Lost Communication with Instrument Panel Cluster (IPC) Control Module Missing Message

  • CAN communication system
  • Combination meter assembly
  • Multiplex network door ECU

Back Door

B

U016387

Lost Communication with Navigation Control Module Missing Message

  • CAN communication system
  • Radio and display receiver assembly
  • Multiplex network door ECU

Back Door

B

U016887

Lost Communication with Toyota Prius Vehicle Security Control Module Missing Message

  • CAN communication system
  • Certification ECU (smart key ECU assembly)
  • Multiplex network door ECU

Back Door

B

U111787

Lost Communication with Accessory Gateway Missing Message

  • CAN communication system
  • Bus buffer ECU
  • Multiplex network door ECU

Back Door

B

U114F87

Lost Communication with Power Integration Module Missing Message

  • CAN communication system
  • Main body ECU (multiplex network body ECU)
  • Multiplex network door ECU

Back Door

B

PROCEDURE

  1. CLEAR DTC

(a) Clear the DTCs.

Body Electrical > Back Door > Clear DTCs
NEXT
  1. REPRODUCE DTC

(a) Turn the ignition switch to ON and wait for at least 10 seconds.

NEXT
  1. CHECK FOR DTC

(a) Check for DTCs.

Body Electrical > Back Door > Trouble Codes

Result

Proceed to

U010087, U010187, U012987, U014087, U015587, U016387, U016887, U111787 or U114F87 is output

A

U010087, U010187, U012987, U014087, U015587, U016387, U016887, U111787 and U114F87 are not output

B

None of the above conditions are met

C

A

GO TO CAN COMMUNICATION SYSTEM

for HEV Model: Click here

for PHEV Model: Click here

B

USE SIMULATION METHOD TO CHECK

C

GO TO DTC CHART

Back Door Closer does not Operate

DESCRIPTION

The back door lock with courtesy light switch assembly is controlled by the multiplex network door ECU. The multiplex network door ECU is activated according to the switch signals in the back door lock with courtesy light switch assembly.

WIRING DIAGRAM

NOTICE:

  • First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this problem.

    Click here

  • Check the smart key system with push-butten start (for Entry Function) first before troubleshooting the power back door system.

    Click here

    Click here

  • Inspect fuses for circuits related to this system before performing the following inspection procedure.
  • If the multiplex network door ECU has been replaced, or if any of the connectors has been disconnected, initialize the power back door system.

    Click here

PROCEDURE

  1. CHECK FOR DTC

(a) Check for DTCs.

Body Electrical > Back Door > Trouble Codes

Result

Proceed to

DTC is not output

A

DTC B225001 is output

B

DTC B225101 is output

C

B

GO TO DIAGNOSTIC TROUBLE CODE CHART

C

GO TO DIAGNOSTIC TROUBLE CODE CHART

A
  1. CHECK BACK DOOR LOCK FUNCTION

(a) Check if the back door can be fully closed by hand.

Result

Proceed to

The back door can be closed normally

A

The back door cannot be closed normally

B

B

IMPROPER FIT OF BACK DOOR, OR A FOREIGN OBJECT IS STUCK IN BACK DOOR

A
  1. CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - AUXILIARY BATTERY AND BODY GROUND)

(a) Disconnect the W13, W17 and W16 multiplex network door ECU connectors.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(W17) Click Connector(W17)

Tester Connection

Condition

Specified Condition

W17-4 (GND) - Body ground

Always

Below 1 Ω

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Click Location & Routing(W13,W16) Click Connector(W13) Click Connector(W16)

Tester Connection

Condition

Specified Condition

W13-7 (ECUB) - Body ground

Ignition switch off

11 to 14 V

W16-5 (B) - Body ground

Ignition switch off

11 to 14 V

W13-9 (IG) - Body ground

Ignition switch ON

11 to 14 V

Ignition switch off

Below 1 V

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. INSPECT BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY

Click here

NG

REPLACE BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY

OK
  1. CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY - MULTIPLEX NETWORK DOOR ECU AND BODY GROUND)

(a) Disconnect the W9 and W8 back door lock with courtesy light switch assembly connectors.

(b) Disconnect the W17 and W13 multiplex network door ECU connectors.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(W9,W17,W8,W13) Click Connector(W9) Click Connector(W17) Click Connector(W8) Click Connector(W13)

Tester Connection

Condition

Specified Condition

W9-2 (M ) - W17-2 (DC )

Always

Below 1 Ω

W9-1 (M-) - W17-6 (DC-)

Always

Below 1 Ω

W8-4 (CTY) - W13-3 (FUL)

Always

Below 1 Ω

W8-2 (FSW) - W13-13 (PAWL)

Always

Below 1 Ω

W8-3 (CLS) - W13-5 (HAF)

Always

Below 1 Ω

W8-6 (OPN) - W13-15 (POS)

Always

Below 1 Ω

W8-1 (E) - Body ground

Always

Below 1 Ω

W9-2 (M ) or W17-2 (DC ) - Body ground

Always

10 kΩ or higher

W9-1 (M-) or W17-6 (DC-) - Body ground

Always

10 kΩ or higher

W8-2 (FSW) or W13-13 (PAWL) - Body ground

Always

10 kΩ or higher

W8-4 (CTY) or W13-3 (FUL) - Body ground

Always

10 kΩ or higher

W8-3 (CLS) or W13-5 (HAF) - Body ground

Always

10 kΩ or higher

W8-6 (OPN) or W13-15 (POS) - Body ground

Always

10 kΩ or higher

OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

Power Back Door cannot be Operated Using Any Switch

DESCRIPTION

The power back door is controlled by the multiplex network door ECU and drives the back door motor.

If the power back door does not operate using any of the operations, a malfunction related to the power back door operation conditions or multiplex network door ECU are possible causes.

WIRING DIAGRAM

NOTICE:

  • First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this problem.

    Click here

  • Inspect fuses for circuits related to this system before performing the following inspection procedure.
  • If the multiplex network door ECU has been replaced, or if any of the connectors has been disconnected, initialize the power back door system.

    Click here

  • If the main body ECU (multiplex network body ECU) is replaced, refer to registration.

    Click here

  • If the 2-step unlock function is enabled via customize settings, only the driver door unlocks when the first unlock operation is performed and the power back door does not operate as all the doors are not unlocked.

PROCEDURE

  1. CHECK Toyota Prius Vehicle CONDITION

(a) Operate the multi-information display in the combination meter assembly and check the customization status.

Display

Description

Default

Setting

Relevant ECU

Power back door

Function that enables or disables the power back door operation.

ON

ON or OFF

Multiplex network door ECU

Result

Proceed to

Customization item is "ON" (power back door system operation is possible)

A

Customization item is "OFF" (power back door system operation is prohibited)

B

B

PERFORM CUSTOMIZE SETTING

A
  1. CHECK CUSTOMIZE SETTING (UNLOCK KEY TWICE FUNCTION)

(a) Read the customize setting "Unlock Key Twice Function" according to the display on the GTS.

Click here

Result

Proceed to

The customize setting is "Disable"

A

The customize setting is "Enable"

B

B

PERFORM CUSTOMIZE SETTING

A
  1. CHECK CUSTOMIZE SETTING (WIRELESS UNLOCK TWICE FUNCTION)

(a) Read the customize setting "Wireless Unlock Twice Function" according to the display on the GTS.

Click here

Result

Proceed to

The customize setting is "Disable"

A

The customize setting is "Enable"

B

B

PERFORM CUSTOMIZE SETTING

A
  1. CHECK CUSTOMIZE SETTING (ENTRY UNLOCK TWICE FUNCTION)

(a) Read the customize setting "Entry Unlock Twice Function" according to the display on the GTS.

Click here

Result

Proceed to

The customize setting is "Disable"

A

The customize setting is "Enable"

B

B

PERFORM CUSTOMIZE SETTING

A
  1. CHECK FOR DTC

(a) Check for DTCs.

Body Electrical > Back Door > Trouble Codes

OK:

DTC is not output

NG

GO TO DIAGNOSTIC TROUBLE CODE CHART

OK
  1. CHECK POWER BACK DOOR SYSTEM CONDITION

(a) Check the power back door system condition.

Result

Proceed to

Power back door does not operate normally

A

Power back door operates normally

B

B

GO TO POWER BACK DOOR CANNOT BE OPERATED FREQUENTLY

A
  1. CHECK COMBINATION METER FUNCTION

(a) Operation check

(1) Check that the shift position indicator light in the combination meter assembly operates correctly in accordance with the operation of the shift lever.

(2) Confirm that the speedometer indicates 0 km/h when the Toyota Prius vehicle is stopped.

OK:

The meter and gauge system operates correctly.

NG

GO TO METER / GAUGE SYSTEM

OK
  1. CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - AUXILIARY BATTERY AND BODY GROUND)

(a) Disconnect the W13, W17 and W16 multiplex network door ECU connectors.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(W17) Click Connector(W17)

Tester Connection

Condition

Specified Condition

W17-4 (GND) - Body ground

Always

Below 1 Ω

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Click Location & Routing(W13,W16) Click Connector(W13) Click Connector(W16)

Tester Connection

Condition

Specified Condition

W13-7 (ECUB) - Body ground

Ignition switch off

11 to 14 V

W16-5 (B) - Body ground

Ignition switch off

11 to 14 V

W13-9 (IG) - Body ground

Ignition switch off

Below 1 V

Ignition switch ON

11 to 14 V

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. READ VALUE USING GTS

(a) Read the Data List according to the display on the GTS.

Body Electrical > Back Door > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

PBD Main Switch

Power back door ON/OFF signal

ON or OFF

Current customize setting displayed

-

Door Lock Signal

Back door condition signal

Lock or Unlock

Lock: Back door locked

Unlock: Back door unlocked

-

Body Electrical > Back Door > Data List

Tester Display

PBD Main Switch

Door Lock Signal

Result

Proceed to

Either item is normal

A

"PBD Main SW" item does not switch to "ON" or "OFF" according to customize setting

B

"Door Lock Signal" item does not switch to "Lock" or "Unlock" according to operation to lock or unlock all doors

C

B

GO TO AUDIO AND VISUAL SYSTEM

C

GO TO STEP 15

A
  1. READ VALUE USING GTS

(a) Read the Data List according to the display on the GTS.

Body Electrical > Back Door > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

PBD Touch Sensor RH

Power back door sensor assembly RH signal

ON, OFF or Open

ON: Power back door sensor assembly RH pressed

OFF: Power back door sensor assembly RH not pressed

Open: Power back door sensor assembly RH circuit open

-

PBD Touch Sensor LH

Power back door sensor assembly LH signal

ON, OFF or Open

ON: Power back door sensor assembly LH pressed

OFF: Power back door sensor assembly LH not pressed

Open: Power back door sensor assembly LH circuit open

-

Body Electrical > Back Door > Data List

Tester Display

PBD Touch Sensor RH

PBD Touch Sensor LH

Result

Proceed to

On the GTS screen, ON or OFF is displayed accordingly

A

On the GTS screen, ON or OFF is not displayed accordingly or Open is displayed for power back door sensor assembly RH

B

On the GTS screen, ON or OFF is not displayed accordingly or Open is displayed for power back door sensor assembly LH

C

A

REPLACE MULTIPLEX NETWORK DOOR ECU

C

GO TO STEP 13

B
  1. INSPECT POWER BACK DOOR SENSOR ASSEMBLY RH

Click here

NG

REPLACE POWER BACK DOOR SENSOR ASSEMBLY RH

OK
  1. CHECK HARNESS AND CONNECTOR (POWER BACK DOOR SENSOR ASSEMBLY RH - MULTIPLEX NETWORK DOOR ECU)

(a) Disconnect the W6 power back door sensor assembly RH connector.

(b) Disconnect the W14 multiplex network door ECU connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(W6,W14) Click Connector(W6) Click Connector(W14)

Tester Connection

Condition

Specified Condition

W6-1 (OSR) - W14-8 (OSR)

Always

Below 1 Ω

W6-2 (OSRE) - W14-9 (OSE)

Always

Below 1 Ω

W6-1 (OSR) or W14-8 (OSR) - Body ground

Always

10 kΩ or higher

W6-2 (OSRE) or W14-9 (OSE) - Body ground

Always

10 kΩ or higher

OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. INSPECT POWER BACK DOOR SENSOR ASSEMBLY LH

Click here

NG

REPLACE POWER BACK DOOR SENSOR ASSEMBLY LH

OK
  1. CHECK HARNESS AND CONNECTOR (POWER BACK DOOR SENSOR ASSEMBLY LH - MULTIPLEX NETWORK DOOR ECU)

(a) Disconnect the W7 power back door sensor assembly LH connector.

(b) Disconnect the W14 multiplex network door ECU connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(W7,W14) Click Connector(W7) Click Connector(W14)

Tester Connection

Condition

Specified Condition

W7-1 (OSL) - W14-1 (OSL)

Always

Below 1 Ω

W7-2 (OSLE) - W14-9 (OSE)

Always

Below 1 Ω

W7-1 (OSL) or W14-1 (OSL) - Body ground

Always

10 kΩ or higher

W7-2 (OSLE) or W14-9 (OSE) - Body ground

Always

10 kΩ or higher

OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - MULTIPLEX NETWORK DOOR ECU)

(a) Disconnect the K15 main body ECU (multiplex network body ECU) connector.

(b) Disconnect the W13 multiplex network door ECU connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(K15,W13) Click Connector(K15) Click Connector(W13)

Tester Connection

Condition

Specified Condition

K15-7 (LSBO) - W13-11 (LIB)

Always

Below 1 Ω

K15-7 (LSBO) or W13-11 (LIB) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

(a) Remove the main body ECU (multiplex network body ECU) with the connector(s) still connected.

*a

Component with harness connected

(Main Body ECU (Multiplex Network Body ECU))

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Click Location & Routing(K15) Click Connector(K15)

Tester Connection

Condition

Specified Condition

K15-7 (LSBO) - Body ground

Back door unlocked

Below 1 V

OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

Power Back Door does not Operate Using Cabin Switch

DESCRIPTION

The power back door control switch sends a signal to the multiplex network door ECU using CAN communication via the main body ECU (multiplex network body ECU).

WIRING DIAGRAM

NOTICE:

  • If the multiplex network door ECU has been replaced, or if any of the connectors has been disconnected, initialize the power back door system.

    Click here

  • First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this problem.

    Click here

  • The auxiliary battery supplies power to the main body ECU (multiplex network body ECU) via the integration control supply. If a main body ECU (multiplex network body ECU) power source malfunction occurs, the integration control supply may be malfunctioning.
  • If the main body ECU (multiplex network body ECU) is replaced, refer to registration.

    Click here

PROCEDURE

  1. CHECK Toyota Prius Vehicle CONDITION

(a) Operate the multi-information display in the combination meter assembly and check the customization status.

Display

Description

Default

Setting

Relevant ECU

Power back door

Function that enables or disables the power back door operation.

ON

ON or OFF

Multiplex network door ECU

Result

Proceed to

Customization item is "ON" (power back door system operation is possible)

A

Customization item is "OFF" (power back door system operation is prohibited)

B

B

PERFORM CUSTOMIZE SETTING

A
  1. CHECK POWER BACK DOOR SYSTEM

(a) Check the power back door system.

Result

Proceed to

Power back door system operates normally

A

Power back door system does not operate normally

B

B

GO TO POWER BACK DOOR CANNOT BE OPERATED FREQUENTLY

A
  1. READ VALUE USING GTS

(a) Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Back Door Operation Switch (Instrument)

Power Back Door Control Switch Signal

ON or OFF

ON: Power Back Door Control Switch ON

OFF: Power Back Door Control Switch OFF

-

Body Electrical > Main Body > Data List

Back Door Operation Switch (Instrument)

OK:

The GTS display changes correctly in response to the switch operation.

OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG
  1. INSPECT POWER BACK DOOR CONTROL SWITCH

Click here

NG

REPLACE POWER BACK DOOR CONTROL SWITCH

OK
  1. CHECK HARNESS AND CONNECTOR (POWER BACK DOOR CONTROL SWITCH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)

(a) Disconnect the K65 power back door control switch connector.

(b) Disconnect the K16 main body ECU (multiplex network body ECU) connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(K65,K16) Click Connector(K65) Click Connector(K16)

Tester Connection

Condition

Specified Condition

K65-5 (CSW) - K16-21 (PBDS)

Always

Below 1 Ω

K65-2 (E) - Body ground

Always

Below 1 Ω

K65-5 (CSW) or K16-21 (PBDS) - Body ground

Always

10 kΩ or higher

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

Power Back Door does not Operate Using Outside Switch

DESCRIPTION

The power back door control switch no.1 signal is sent to the multiplex network door ECU.

If the power back door does not operate using the power back door control switch no.1, a power back door control switch no.1 circuit malfunction is a possible cause.

WIRING DIAGRAM

NOTICE:

If the multiplex network door ECU has been replaced, or if any of the connectors has been disconnected, initialize the power back door system.

Click here

PROCEDURE

  1. CHECK Toyota Prius Vehicle CONDITION

(a) Operate the multi-information display in the combination meter assembly and check the customization status.

Display

Description

Default

Setting

Relevant ECU

Power back door

Function that enables or disables the power back door operation.

ON

ON or OFF

Multiplex network door ECU

Result

Proceed to

Customization item is "ON" (power back door system operation is possible)

A

Customization item is "OFF" (power back door system operation is prohibited)

B

B

PERFORM CUSTOMIZE SETTING

A
  1. CHECK POWER BACK DOOR SYSTEM

(a) Check the power back door system.

Result

Proceed to

Power back door system operates normally

A

Power back door system does not operate normally

B

B

GO TO POWER BACK DOOR CANNOT BE OPERATED FREQUENTLY

A
  1. READ VALUE USING GTS

(a) Read the Data List according to the display on the GTS.

Body Electrical > Back Door > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

PBD Close Switch

Power back door control switch no.1 signal

ON or OFF

ON: Power back door control switch no.1 pushed

OFF: Power back door control switch no.1 not pushed

-

Body Electrical > Back Door > Data List

PBD Close Switch

OK:

The GTS display changes correctly in response to the switch operation.

OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG
  1. INSPECT POWER BACK DOOR CONTROL SWITCH NO.1

Click here

NG

REPLACE POWER BACK DOOR CONTROL SWITCH NO.1

OK
  1. CHECK HARNESS AND CONNECTOR (POWER BACK DOOR CONTROL SWITCH NO.1 - MULTIPLEX NETWORK DOOR ECU AND BODY GROUND)

(a) Disconnect the W2 power back door control switch no.1 connector.

(b) Disconnect the W13 multiplex network door ECU connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(W2,W13) Click Connector(W2) Click Connector(W13)

Tester Connection

Condition

Specified Condition

W2-5 (CLS) - W13-14 (BDDN)

Always

Below 1 Ω

W2-2 (E) - Body ground

Always

Below 1 Ω

W2-5 (CLS) or W13-14 (BDDN) - Body ground

Always

10 kΩ or higher

OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

Power Back Door Warning System does not Operate

DESCRIPTION

Depending on the operating conditions, the multiplex network door ECU sounds the buzzer and outputs a hazard light flash signal to the combination meter assembly.

WIRING DIAGRAM

NOTICE:

  • If the multiplex network door ECU has been replaced, or if any of the connectors has been disconnected, initialize the power back door system.

    Click here

  • First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this problem.
  • If the main body ECU (multiplex network body ECU) is replaced, refer to registration.

    Click here

  • The auxiliary battery supplies power to the main body ECU (multiplex network body ECU) via the integration control supply. If a main body ECU (multiplex network body ECU) power source malfunction occurs, the integration control supply may be malfunctioning.

PROCEDURE

  1. CHECK OPERATION

(a) Operate the power back door and check that the warning buzzer and hazard warning light operate.

Result

Proceed to

Hazard warning light does not come on

A

Power back door warning buzzer does not operate

B

B

GO TO STEP 6

A
  1. CHECK WIRELESS DOOR LOCK CONTROL SYSTEM (HAZARD ANSWER-BACK FUNCTION)

(a) Check wireless door lock operation.

Click here

OK:

Hazard answer-back function operates normally.

NG

GO TO WIRELESS DOOR LOCK CONTROL SYSTEM

OK
  1. REPLACE MULTIPLEX NETWORK DOOR ECU

(a) Temporarily replace the multiplex network door ECU with a new or normally functioning one.

Click here

NEXT
  1. INITIALIZE MULTIPLEX NETWORK DOOR ECU

(a) Perform the initialization for the multiplex network door ECU.

Click here

NEXT
  1. CHECK POWER BACK DOOR SYSTEM

(a) Check that the power back door hazard warning lights operate normally.

Click here

OK:

The power back door hazard warning lights operate normally.

OK

END (MULTIPLEX NETWORK DOOR ECU WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

  1. CHECK Toyota Prius Vehicle CONDITION

(a) Using the GTS, check the customization status.

PSD & PBD operation

Tester Display

Description

Default

Setting

ECU

PBD Buzzer Function

Function that changes the power back door warning buzzer setting.

OFF

$00:OFF,$01:ON

Multiplex network door ECU

Result

Proceed to

Customization item is "ON"

A

Customization item is "OFF"

B

B

PERFORM CUSTOMIZE SETTING

A
  1. PERFORM ACTIVE TEST USING GTS

(a) Perform the Active Test according to the display on the GTS.

Body Electrical > Back Door > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

PBD Buzzer (Small Volume)

Power back door warning buzzer sound (small volume)

Start

-

PBD Buzzer (Middle Volume)

Power back door warning buzzer sound (Middle volume)

Start

-

PBD Buzzer (Large Volume)

Power back door warning buzzer sound (Large volume)

Start

-

Body Electrical > Back Door > Active Test

PBD Buzzer (Small Volume)

Body Electrical > Back Door > Active Test

PBD Buzzer (Middle Volume)

Body Electrical > Back Door > Active Test

PBD Buzzer (Large Volume)

OK:

Power back door warning buzzer sounds.

OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG
  1. CHECK MULTIPLEX NETWORK DOOR ECU

(a) Disconnect the W15 Power back door warning buzzer connector.

(b) Perform the Active Test according to the display on the GTS.

Body Electrical > Back Door > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

PBD Buzzer (Middle Volume)

Power back door warning buzzer sound (Middle volume)

Start

-

Body Electrical > Back Door > Active Test

PBD Buzzer (Middle Volume)

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Click Location & Routing(W15) Click Connector(W15)

Tester Connection

Condition

Specified Condition

W15-1 (BZR ) - W15-2 (BZR-)

Active Test "PBD Buzzer (Middle Volume)" is not performed

Below 1 V

Active Test "PBD Buzzer (Middle Volume)" is being performed

Pulse generation

(frequency: 2 kHz, high voltage: 11 to 14 V, low voltage: below 1 V)

*a

Front view of wire harness connector

(to Power Back Door Warning Buzzer)

OK

REPLACE POWER BACK DOOR WARNING BUZZER

NG
  1. CHECK HARNESS AND CONNECTOR (POWER BACK DOOR WARNING BUZZER - MULTIPLEX NETWORK DOOR ECU AND BODY GROUND)

(a) Disconnect the W15 power back door warning buzzer connector.

(b) Disconnect the W13 multiplex network door ECU connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(W15,W13) Click Connector(W15) Click Connector(W13)

Tester Connection

Condition

Specified Condition

W15-1 (BZR ) - W13-1 (BZR )

Always

Below 1 Ω

W15-2 (BZR-) - Body ground

Always

Below 1 Ω

W15-1 (BZR ) or W13-1 (BZR ) - Body ground

Always

10 kΩ or higher

OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

Jam Protection Function Activates During Power Back Door Operation

DESCRIPTION

The power back door is controlled by the multiplex network door ECU and the back door motor is driven. During motor operation, the power back door (touch sensor) used for jam protection checks for obstruction by foreign objects, etc. by detecting changes in resistance due to contact.

Furthermore, the speed of the back door is monitored using the pulse sensor (power back door unit assembly) and if a change in speed is detected, it is judged that there is an obstruction by a foreign object and the door direction is reversed.

WIRING DIAGRAM

NOTICE:

If the multiplex network door ECU has been replaced, or if any of the connectors has been disconnected, initialize the power back door system.

Click here

PROCEDURE

  1. CHECK POWER BACK DOOR SYSTEM

(a) Check if there are any foreign objects interfering with back door operation.

Result

Proceed to

There are no foreign objects

A

There are foreign objects

B

B

REMOVE FOREIGN OBJECT

A
  1. CHECK BACK DOOR OPERATION

(a) Set the power back door system main switch to "OFF"

(1) Operate the multi-information display in the combination meter assembly and disable the function.

Display

Description

Default

Setting

Relevant ECU

Power back door

Function that enables or disables the power back door operation.

On

On or Off

Multiplex network door ECU

(2) Check that the back door operates smoothly without catching (does not feel heavy) when manually opened and closed.

NG

ADJUST BACK DOOR

OK
  1. READ VALUE USING GTS

(a) Check the Data List to determine if the power back door sensor assembly functions properly.

Body Electrical > Back Door > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

PBD Touch Sensor RH

Power back door sensor assembly RH signal

ON, OFF or Open

ON: Power back door sensor assembly RH pressed

OFF: Power back door sensor assembly RH not pressed

Open: Power back door sensor assembly RH circuit open

-

PBD Touch Sensor LH

Power back door sensor assembly LH signal

ON, OFF or Open

ON: Power back door sensor assembly LH pressed

OFF: Power back door sensor assembly LH not pressed

Open: Power back door sensor assembly LH circuit open

-

Body Electrical > Back Door > Data List

Tester Display

PBD Touch Sensor RH

PBD Touch Sensor LH

Result

Proceed to

On the GTS screen, ON or OFF is displayed accordingly

A

On the GTS screen, ON or OFF is not displayed accordingly or Open is displayed for power back door sensor assembly RH

B

On the GTS screen, ON or OFF is not displayed accordingly or Open is displayed for power back door sensor assembly LH

C

B

GO TO STEP 6

C

GO TO STEP 8

A
  1. CHECK POWER BACK DOOR UNIT ASSEMBLY LH

(a) Using an oscilloscope, check the waveform of each terminal from the rear of the multiplex network door ECU connector.

*a

Component with harness connected

(Multiplex Network Door ECU)

*b

Waveform (CH1)

*c

Waveform (CH2)

-

-

Measurement Condition:

Item

Condition

Tester Connection

  • CH1: W14-13 (DS1) - Body ground
  • CH2: W14-5 (DS2) - Body ground

Tool Setting

2 V/DIV., 2 ms./DIV.

Toyota Prius Vehicle Condition

Open and close the back door by hand.

HINT:

  • The period changes in accordance to the speed at which the back door is opened and closed by hand.
  • The wave height changes in accordance with the auxiliary battery voltage.
NG

REPLACE POWER BACK DOOR UNIT ASSEMBLY LH

OK
  1. CHECK POWER BACK DOOR UNIT ASSEMBLY RH

(a) Using an oscilloscope, check the waveform of each terminal from the rear of the multiplex network door ECU connector.

*a

Component with harness connected

(Multiplex Network Door ECU)

*b

Waveform (CH1)

*c

Waveform (CH2)

-

-

Measurement Condition:

Item

Condition

Tester Connection

  • CH1: W14-6 (DS12) - Body ground
  • CH2: W14-12 (DS22) - Body ground

Tool Setting

2 V/DIV., 2 ms./DIV.

Toyota Prius Vehicle Condition

Open and close the back door by hand.

HINT:

  • The period changes in accordance to the speed at which the back door is opened and closed by hand.
  • The wave height changes in accordance with the auxiliary battery voltage.
OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPLACE POWER BACK DOOR UNIT ASSEMBLY RH

  1. INSPECT POWER BACK DOOR SENSOR ASSEMBLY RH

Click here

NG

REPLACE POWER BACK DOOR SENSOR ASSEMBLY RH

OK
  1. CHECK HARNESS AND CONNECTOR (POWER BACK DOOR SENSOR ASSEMBLY RH - MULTIPLEX NETWORK DOOR ECU)

(a) Disconnect the W6 power back door sensor assembly RH connector.

(b) Disconnect the W14 multiplex network door ECU connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(W6,W14) Click Connector(W6) Click Connector(W14)

Tester Connection

Condition

Specified Condition

W6-1 (OSR) - W14-8 (OSR)

Always

Below 1 Ω

W6-2 (OSRE) - W14-9 (OSE)

Always

Below 1 Ω

W6-1 (OSR) or W14-8 (OSR) - Body ground

Always

10 kΩ or higher

W6-2 (OSRE) or W14-9 (OSE) - Body ground

Always

10 kΩ or higher

OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. INSPECT POWER BACK DOOR SENSOR ASSEMBLY LH

Click here

NG

REPLACE POWER BACK DOOR SENSOR ASSEMBLY LH

OK
  1. CHECK HARNESS AND CONNECTOR (POWER BACK DOOR SENSOR ASSEMBLY LH - MULTIPLEX NETWORK DOOR ECU)

(a) Disconnect the W7 power back door sensor assembly LH connector.

(b) Disconnect the W14 multiplex network door ECU connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(W7,W14) Click Connector(W7) Click Connector(W14)

Tester Connection

Condition

Specified Condition

W7-1 (OSL) - W14-1 (OSL)

Always

Below 1 Ω

W7-2 (OSLE) - W14-9 (OSE)

Always

Below 1 Ω

W7-1 (OSL) or W14-1 (OSL) - Body ground

Always

10 kΩ or higher

W7-2 (OSLE) or W14-9 (OSE) - Body ground

Always

10 kΩ or higher

OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

Lock Function does not Operate (Close &)

DESCRIPTION

The back door control switch signal is sent to the multiplex network door ECU. If the power back door system does not operate when the back door control switch is operated, the back door control switch circuit may be malfunctioning.

WIRING DIAGRAM

NOTICE:

  • If the multiplex network door ECU has been replaced, or if any of the connectors has been disconnected, initialize the power back door system.

    Click here

  • Check the smart key system with push-butten start (for Entry Function) first before troubleshooting the power back door system.

    Click here

  • This function cannot be used with only the digital key.*
    • *: w/ Digital Key

PROCEDURE

  1. READ VALUE USING GTS

(a) Read the Data List according to the display on the GTS.

Body Electrical > Back Door > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Close and Lock Switch

Back door control switch signal

OFF or ON

ON: Back door control switch pressed

OFF: Back door control switch not pressed

-

Body Electrical > Back Door > Data List

Close and Lock Switch

OK:

The GTS display changes correctly in response to the switch operation.

OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG
  1. INSPECT BACK DOOR CONTROL SWITCH

Click here

NG

REPLACE BACK DOOR CONTROL SWITCH

OK
  1. CHECK HARNESS AND CONNECTOR (BACK DOOR CONTROL SWITCH - MULTIPLEX NETWORK DOOR ECU AND BODY GROUND)

(a) Disconnect the W13 multiplex network door ECU connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(W3,W13) Click Connector(W3) Click Connector(W13)

Tester Connection

Condition

Specified Condition

W3-5 (MSW) - W13-4 (CLSW)

Always

Below 1 Ω

W3-2 (MSE) - Body ground

Always

Below 1 Ω

W3-5 (MSW) or W13-4 (CLSW) - Body ground

Always

10 kΩ or higher

OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

Power Back Door cannot be Operated Frequently

DESCRIPTION

If the power back door system does not operate, a vehicle malfunction, environmental problem, and customer (including passenger) operation are possible causes. Using Vehicle Control History (RoB) allows the cause to be narrowed down, and repair, replacement, and in some circumstances explaining the environment or usage conditions can help resolve the malfunction.

NOTICE:

  • If the Toyota Prius vehicle or vehicle controls are operated (for example, during initial inspection when the vehicle is brought in for repair) before vehicle control history (RoB) has been read out and saved, the vehicle control history (RoB) information could be lost.
  • The function "Read vehicle control history (RoB)" uses the current system time setting inside the GTS and the time counter inside the controlling ECU to calculate the timings shown in the Toyota Prius vehicle control history (RoB). For this reason, before reading out the vehicle control history (RoB), first make sure that the GTS system clock is accurately set to the current time.
  • The time counter in the control ECU may deviate by up to /- 10% due to the characteristics of the time counter.
  • The time counter in the control ECU is reset approximately 34 days before the "Current" value due to the characteristics of the time counter. Therefore, the time information stored before the 34th day may not be accurately displayed.

PROCEDURE

  1. CHECK Toyota Prius Vehicle CONTROL HISTORY (RoB)

(a) Using the GTS, check for vehicle control history (RoB).

Body Electrical > Back Door > Utility

Toyota Prius Vehicle Control History (RoB)

Body Electrical > Main Body > Utility

Vehicle Control History (RoB)

Result

Proceed to

Toyota Prius Vehicle control history (RoB) item is not stored.

A

Vehicle control history (RoB) item is stored.

B

A

USE SIMULATION METHOD TO CHECK

B

END (explain the cause why it did not operate to the customer)