Roof Headlining

In this manual: Roof Headlining
How To Troubleshoot Ecu Controlled Systems — 1How To Use This Manual — 1Identification Information — 1Repair Instruction — 1Terms — 12zr-fxe Air Cleaner Filter Element — 12zr-fxe Auxiliary Battery — 12zr-fxe Coolant (for Engine Coolant) — 12zr-fxe Oil And Oil Filter — 12zr-fxe Spark Plug — 1Air Conditioning Filter — 1Battery Cooling Filter — 1Brake Fluid — 1Coolant (for Inverter) — 1Front Brake Flexible Hose — 1Front Disc Brake Pad — 1Front Lower Ball Joint — 1Front Wheel Alignment — 1Front Wiper Rubber — 1General Maintenance — 1M20a-fxs Air Cleaner Filter Element — 1M20a-fxs Auxiliary Battery — 1M20a-fxs Coolant (for Engine Coolant) — 1M20a-fxs Oil And Oil Filter — 1M20a-fxs Spark Plug — 1Pa10/pb10/pb12 Hybrid Transaxle Fluid — 1Q810 Hybrid Transaxle Fluid — 1Rear Brake Flexible Hose — 1Rear Disc Brake Pad — 1Rear Wheel Alignment — 1Steering Column — 1Tire And Wheel — 1Transmitter Battery — 1When Disconnecting Or Reconnecting Battery Terminal — 1When Replacing Or Removing/installing Parts — 1Automatic High Beam Main Switch — 1Automatic High Beam System — 1Driver Monitor Camera — 1Driver Monitor Camera System — 1Driver Monitor Ecu — 1Front Camera — 1Front Camera System — 1Front Radar Sensor System — 1Front Side Radar Sensor — 1Front Side Radar Sensor System — 1Millimeter Wave Radar Sensor — 1Utility — 1Advanced Park — 1Advanced Park Main Switch — 1Amplifier Antenna — 1Audio And Visual System — 1Front Door Speaker — 1Instrument Panel Speaker — 1Microphone — 1Noise Filter — 1Pillar Speaker — 1Radio Antenna Cord (for Back Door) — 1Radio Antenna Cord (for Instrument Panel) — 1Radio Antenna Cord (for Roof) — 1Radio Receiver — 1Rear Door Speaker — 1Roof Antenna — 1Stereo Component Amplifier — 1Stereo Jack Adapter Assembly — 1Window Glass Antenna Wire — 1Back-up Battery — 1Dcm(telematics Transceiver) — 1Manual(sos)switch — 1Safety Connect System — 1Telephone And Gps Antenna (for Front Side) — 1Telephone And Gps Antenna (for Roof Side) — 1Telephone And Gps Antenna Cords — 1Garage Door Opener System (for Digital Inner Mirror) — 1Garage Door Opener System (for Ec Inner Mirror) — 1Blind Spot Monitor Sensor — 1Blind Spot Monitor System — 1Clearance Warning Ecu — 1Intuitive Parking Assist System — 1Panoramic View Monitor Switch — 1Panoramic View Monitor System — 1Parking Assist Ecu — 1Parking Assist Light — 1Parking Assist Monitor System — 1Parking Support Brake System — 1Rear View Monitor System — 1Television Camera (for Front) — 1Television Camera (for Rear) — 1Television Camera (for Side) — 1Ultrasonic Sensor (for Front) — 1Ultrasonic Sensor (for Rear) — 1Brake Actuator — 1Brake Pedal Stroke Sensor — 1Electronically Controlled Brake System — 1Front Speed Sensor — 1Rear Speed Sensor (for Awd) — 1Steering Angle Sensor — 1Brake Booster — 1Brake Fluid — 1Brake Line — 1Brake Pedal — 1Brake System — 1Electric Parking Brake Actuator — 1Electric Parking Brake Switch — 1Electric Parking Brake System — 1Forced Release — 1Front Axle Hub — 1Front Axle Hub Bolt — 1Rear Axle Carrier (for 2wd) — 1Rear Axle Carrier (for Awd) — 1Rear Axle Hub (for 2wd) — 1Rear Axle Hub (for Awd) — 1Rear Axle Hub Bolt — 1Steering Knuckle — 1Drive Shaft System — 1Front Drive Shaft Assembly — 1Rear Drive Shaft Assembly — 1Combination Switch — 1Electronic Shift Lever System — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Oil Seal — 1Hybrid Transaxle System — 1Input Shaft Oil Seal — 1Motor Cable — 1Pa10 Hybrid Vehicle Transaxle — 1Pa10 Manual Parking Lock Release — 1Pa10 Oil Cooler — 1Pb10/pb12 Hybrid Vehicle Transaxle — 1Pb10/pb12 Manual Parking Lock Release — 1Pb10/pb12 Oil Cooler — 1Shift Control Actuator — 1Shift Lever — 1Shift Lever Knob — 1Differential Side Gear Shaft — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Side Gear Oil Seal — 1Motor Cable — 1Rear Traction Motor — 1Coolant (for Engine) — 1Cooling Fan Motor — 1Cooling Fan System — 1Radiator — 1Relay — 1Thermostat — 1Water Pump — 1Canister — 1Egr Cooler — 1Egr Valve — 1Emission Control System — 1Fuel Tank Cap — 1Pcv Valve — 1Purge Valve — 1Vacuum Sensor — 1Air Fuel Ratio Sensor — 1Camshaft Oil Control Valve — 1Camshaft Position Sensor — 1Crankshaft Position Sensor — 1Ecm — 1Engine Coolant Temperature Sensor — 1Heated Oxygen Sensor — 1Ignition Coil And Spark Plug — 1Ignition System — 1Knock Sensor — 1Mass Air Flow Meter — 1Relay — 1Sfi System — 1Throttle Body — 1Camshaft — 1Cylinder Block — 1Cylinder Head — 1Cylinder Head Gasket — 1Engine — 1Engine Assembly — 1Engine Unit — 1Front Crankshaft Oil Seal — 1Rear Crankshaft Oil Seal — 1Fuel Filter — 1Fuel Injector — 1Fuel Pressure Regulator — 1Fuel Pump — 1Fuel Sender Gauge Assembly — 1Fuel System — 1Fuel Tank — 1Air Cleaner Filter Element — 1Exhaust Manifold — 1Exhaust Pipe — 1Intake Manifold — 1Intake System — 1Lubrication System — 1Oil And Oil Filter — 1Oil Pan And Oil Level Sensor — 1Oil Pressure Switch — 1Oil Pump — 1Accelerator Pedal Sensor — 1Battery Blower (for Hev Model) — 1Battery Ecu (for Hev Model) — 1Battery Ecu (for Phev Model) — 1Battery Voltage Sensor (for Phev Model) — 1Charge Cable (for Phev Model) — 1Charge Indicator (for Phev Model) — 1Charge Inlet (for Phev Model) — 1Combination Switch — 1Coolant (for Inverter) — 1Cooler (for Phev Model) — 1Electric Vehicle Charger Assembly (for Phev Model) — 1Frame Wire (for Hev Model) — 1Frame Wire (for Phev Model) — 1Heater Relay (for Phev Model) — 1Hv Battery (for Hev Model) — 1Hv Battery (for Phev Model) — 1Hv Battery Heater (for Phev Model) — 1Hv Battery Stack (for Phev Model) — 1Hv Relay Assembly (for Hev Model) — 1Hv Relay Assembly (for Phev Model) — 1Hybrid Battery System (for 2zr-fxe) — 1Hybrid Battery System (for M20a-fxs) — 1Hybrid Battery System (for Phev Model) — 1Hybrid Vehicle Control Ecu — 1Inverter With Converter (for Hev Model) — 1Motor Generator Control System (for 2zr-fxe) — 1Plug-in Charge Control System (for Phev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Service Plug Grip (for Hev Model) — 1Sub Radiator — 1Water Pump With Motor — 1Auxiliary Battery — 1Battery Current Sensor — 1Charging System — 1Solar Charging System — 1Solar Control Unit — 1Solar Roof — 1Can Communication System (for Hev Model) — 1Lin Communication System — 1Network Gateway Ecu — 1Integration Control Supply — 1Main Body Ecu — 1Power Integration System — 1Sub Battery System — 1Power Steering Ecu — 1Power Steering System — 1Heated Steering Wheel Controller — 1Heated Steering Wheel System — 1Steering Column Assembly — 1Steering Heater Switch — 1Steering Pad Switch — 1Steering System — 1Steering Wheel — 1Front Lower Ball Joint — 1Front Lower Suspension Arm (for 2zr-fxe Lh Side) — 1Front Lower Suspension Arm (for 2zr-fxe Rh Side) — 1Front Lower Suspension Arm (for M20a-fxs) — 1Front Shock Absorber — 1Front Stabilizer Bar — 1Front Suspension Member — 1Rear Coil Spring — 1Rear Lower Arm (for Awd Lh Side) — 1Rear Lower Arm (for Awd Rh Side) — 1Rear Lower Arm (for Hev Model 2wd) — 1Rear Lower Arm (for Phev Model) — 1Rear Shock Absorber — 1Rear Stabilizer Bar — 1Rear Suspension Member (for 2wd) — 1Rear Suspension Member (for Awd) — 1Rear Trailing Arm — 1Rear Upper Arm — 1Tire And Wheel System — 1Tire Repair Seal — 1Tire Pressure Warning Receiver — 1Tire Pressure Warning System — 1Tire Pressure Warning Valve — 1Acoustic Vehicle Alerting System — 1Vehicle Approaching Speaker — 1Vehicle Approaching Speaker Ecu — 1Back Door — 1Back Door Closer Ecu — 1Back Door Opener Switch — 1Back Door Support — 1Back Door Weatherstrip — 1Charge Lid Courtesy Switch — 1Charge Lid Opener Motor Assembly — 1Charge Lid Opener System — 1Charge Lid Opener Unit — 1Front Door — 1Front Door Opening Trim Weatherstrip — 1Fuel Lid Opener Motor Assembly — 1Fuel Lid Opener Switch — 1Fuel Lid Opener System — 1Hood — 1Hood Lock Control Cable Assembly — 1Power Back Door Closer Switch — 1Power Back Door Control Switch — 1Power Back Door Drive Unit — 1Power Back Door System — 1Power Back Door Touch Sensor — 1Power Back Door Warning Buzzer — 1Rear Door — 1Rear Door Opening Trim Weatherstrip — 1Reserve Lock Switch — 1Front Bumper — 1Front Door Belt Moulding — 1Front Door Window Frame Moulding — 1Front Fender — 1Front Pillar Upper Cover — 1Grille Shutter — 1Grille Shutter System — 1Name Plate — 1Quarter Garnish — 1Rear Bumper — 1Rear Door Belt Moulding — 1Rear Door Window Frame Moulding — 1Rear Wheel House Plate — 1Rocker Panel Moulding — 1Roof Drip Side Finish Moulding — 1Roof Garnish — 1Wheel Opening Moulding (for Front Side) — 1Wheel Opening Moulding (for Rear Side) — 1Windshield Outside Moulding — 1Horn — 1Horn System — 1Relay — 1Automatic Light Control Sensor — 1Back-up Light Assembly — 1Charge Lid Light — 1Front Marker Light — 1Hazard Warning Switch — 1Headlight Assembly — 1Headlight Dimmer Switch — 1Headlight Leveling Switch — 1High Mounted Stop Light Assembly — 1Illumination Light Assembly — 1License Plate Light Assembly — 1Lighting System — 1Rear Combination Light Assembly — 1Rear Light Assembly — 1Rear Side Marker Light Assembly — 1Relay — 1Side Turn Signal Light Assembly — 1Stop Light Switch — 1Switch Housing — 1Outer Mirror Switch — 1Outer Rear View Mirror — 1Outer Rear View Mirror Cover — 1Outer Rear View Mirror Glass — 1Power Mirror Control System — 1Back Door Glass — 1Front Passenger Side Power Window Switch — 1Power Window Control System — 1Power Window Master Switch — 1Power Window Regulator Motor (for Front Door) — 1Power Window Regulator Motor (for Rear Door) — 1Rear Power Window Switch — 1Relay — 1Roof Window Fix Glass — 1Window Defogger System — 1Windshield Deicer Switch — 1Windshield Deicer System — 1Windshield Glass — 1Front Wiper Motor — 1Rain Sensor — 1Relay — 1Washer Motor — 1Washer Nozzle (for Front Side) — 1Washer Nozzle (for Rear Television Camera) — 1Wiper And Washer System — 1Wiper Ecu — 1Wiper Switch — 1Back Door Lock — 1Door Control Receiver — 1Door Control Switch — 1Door Control Transmitter — 1Door Lock Release Motor (for Rear Side) — 1Door Outside Handle (for Rear Side) — 1Front Door Lock — 1Power Door Lock Control System — 1Rear Door Lock — 1Transmitter Battery — 1Wireless Door Lock Control System — 1Accumulator — 1Air Conditioning Amplifier — 1Air Conditioning Panel — 1Air Conditioning Pressure Sensor — 1Air Conditioning Unit — 1Ambient Temperature Sensor — 1Blower Unit — 1Condenser (for Hev Model) — 1Condenser (for Phev Model) — 1Discharge Temperature Sensor — 1Electric Expansion Valve (cooling) — 1Electric Expansion Valve (heating) — 1Evaporator Pipe Temperature Sensor — 1Evaporator Pressure Regulator — 1Front Blower Motor — 1Front Evaporator Front Solenoid Valve — 1Air Conditioning System (for Hev Model) — 1Front Evaporator Temperature Sensor — 1Heat Exchanger Temperature Sensor — 1Heat Pump Ecu — 1High Pressure Magnetic Valve — 1Humidity Sensor — 1Internal Condenser Temperature Sensor — 1Low Pressure Magnetic Valve — 1Refrigerant (for Hfc-134a(r134a)) — 1Refrigerant Line (for Hev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Room Temperature Sensor — 1Solar Sensor — 1Floor Carpet — 1Front Console Box — 1Instrument Panel Safety Pad — 1Roof Headlining — 1Roof Sunshade — 1Ambient Light (for Driver Side) — 1Ambient Light (for Front Passenger Side) — 1Back Door Courtesy Switch — 1Footwell Light — 1Glove Box Light — 1Lighting System — 1Luggage Compartment Room Light — 1Personal Light — 1Room Light — 1Vanity Light — 1Vanity Light Switch — 1Combination Meter — 1Meter / Gauge System — 1Trip Switch — 1Digital Inner Mirror — 1Digital Rear-view Mirror System — 1Inner Mirror Monitor Camera — 1Inner Rear View Mirror (w/o Ec Mirror) — 1Accessory Power Outlet System — 1Power Outlet Socket (for Console Box Front Side) — 1Power Outlet Socket (for Console Box Rear Side) — 1Power Outlet Socket (for Console Box) — 1Power Outlet Socket (for Luggage Compartment) — 1Power Outlet Switch — 1Wireless Charger Assembly — 1Wireless Charging System — 1Climate Control Seat System — 1Front Power Seat Control System (w/ Memory) — 1Front Power Seat Motor Assembly — 1Front Seat Assembly (for Power Seat) — 1Front Seat Cushion Heater (for Power Seat) — 1Front Seatback Heater (for Power Seat) — 1Lumbar Support Adjuster Assembly — 1Power Seat Control Ecu — 1Power Seat Switch — 1Power Seat Track Rail Assembly — 1Rear Seat Assembly — 1Rear Seat Cushion Heater — 1Rear Seat Reminder System — 1Rear Seatback Heater — 1Seat Heater Control — 1Seat Heater Switch (for Front Seat) — 1Seat Heater Switch (for Rear Side) — 1Seat Heater System — 1Seat Memory Switch — 1Child Restraint Seat Anchor Bracket — 1Front Seat Inner Belt Assembly — 1Front Seat Outer Belt Assembly — 1Occupant Detection Sensor (for Front Passenger Side) — 1Rear Center Seat Outer Belt Assembly — 1Rear Seat Inner Belt Assembly (for Rh Side) — 1Rear Seat Outer Belt Assembly — 1Seat Belt Warning System (w/ Occupant Classification System) — 1Tongue Plate Stopper — 1Airbag System — 1Center Airbag Sensor Assembly — 1Curtain Shield Airbag Assembly — 1Front Airbag Sensor — 1Front Passenger Airbag Assembly — 1Front Seat Side Airbag Assembly — 1Inspection After Collision — 1Knee Airbag Assembly — 1Occupant Classification System — 1Rear Seat Side Airbag Assembly — 1Side Airbag Sensor (for Center Pillar) — 1Side Airbag Sensor (for Front Door) — 1Spiral Cable — 1Steering Pad — 1Certification Ecu — 1Digital Key Ecu — 1Digital Key Receiver (for Front Floor) — 1Digital Key Receiver (for Outside Luggage Compartment) — 1Digital Key Receiver (for Rear Door) — 1Digital Key System — 1Electrical Key Oscillator (for Front Floor) — 1Electrical Key Oscillator (for Outside Luggage Compartment) — 1Electrical Key Oscillator (for Rear Floor) — 1Engine Hood Courtesy Switch — 1Id Code Box — 1Smart Key System (for Start Function) — 1
~32min read
2special tools
010203040503022N·mlb·ft
Tightening torque found on this page
  • Removal
  • Disassembly
  • Reassembly
  • Installation

Removal

REMOVAL

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during roof headlining assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.
w/ Occupant Classification System:
  • Front passenger seat*

Zero point calibration (Occupant classification system)

  • Occupant Classification System
  • Passenger airbag ON/OFF indicator
  • Airbag System (Front passenger side)
  • Seat Belt Warning System (Front passenger)

CAUTION:

Be sure to read Precaution thoroughly before servicing.

Click here

NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click here

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

Learning completes when Toyota Prius vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed

Necessary Procedures

Link

Front Camera System

Drive the Toyota Prius vehicle straight ahead at 35 km/h or more for 5 seconds or more.

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed

Necessary Procedures

Link

*1: w/o Power Back Door System

*2: w/ Power Back Door System

Power Door Lock Control System*1

  • Back door opener

Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.

Power Back Door System*2

Reset back door close position

Air Conditioning System

for HEV Model:
  • After the ignition switch is turned to ON, the servo motor standard position is recognized.
for PHEV Model:
  • After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized.

-

COMPONENTS (REMOVAL)

Procedure

Part Name Code

1

TONNEAU COVER ASSEMBLY

64910J

-

-

-

2

DECK BOARD ASSEMBLY

58410B

-

-

-

3

DECK FLOOR BOX RH

64995

-

-

-

4

DECK FLOOR BOX LH

64997

-

-

-

5

BATTERY SERVICE HOLE COVER ASSEMBLY

58440

-

-

-

*A

for Type A

*B

for Type B

*C

w/o Spare Tire

*D

w/ Spare Tire

*E

w/ Battery Cover

-

-

*a

HINT:

As the illustration shown is an example, the actual details may differ.

-

-

Procedure

Part Name Code

6

FRONT SEAT ASSEMBLY LH

-

-

-

-

7

FRONT SEAT ASSEMBLY RH

-

-

-

-

8

REAR SEAT ASSEMBLY

-

-

-

-

9

REAR CONSOLE BOX ASSEMBLY

-

-

-

-

Procedure

Part Name Code

10

FRONT DOOR SCUFF PLATE LH

67914

-

-

-

11

COWL SIDE TRIM BOARD LH

62112

-

-

-

12

FRONT DOOR OPENING TRIM WEATHERSTRIP LH

62312B

-

-

-

13

FRONT PILLAR GARNISH LH

62212

-

-

14

REAR DOOR SCUFF PLATE INSIDE LH

67918F

-

-

-

15

REAR DOOR OPENING TRIM WEATHERSTRIP LH

62332A

-

-

-

16

REAR UNDER SIDE COVER LH

76974E

-

-

-

17

LAP BELT OUTER ANCHOR COVER

73233

-

-

-

18

FRONT SEAT OUTER BELT ASSEMBLY LH

73220

-

-

-

19

CENTER PILLAR LOWER GARNISH LH

62414A

-

-

-

20

CENTER PILLER GARNISH ASSEMBLY LH

62420A

-

-

-

*A

for LH Side

*B

for HEV Model

●

Non-reusable part

-

-

Procedure

Part Name Code

21

FRONT DOOR SCUFF PLATE RH

67913

-

-

-

22

COWL SIDE TRIM BOARD RH

62111C

-

-

-

23

FRONT DOOR OPENING TRIM WEATHERSTRIP RH

62311B

-

-

-

24

FRONT PILLAR GARNISH RH

62211

-

-

25

REAR DOOR SCUFF PLATE INSIDE RH

67917F

-

-

-

26

REAR DOOR OPENING TRIM WEATHERSTRIP RH

62331A

-

-

-

27

REAR UNDER SIDE COVER RH

76973E

-

-

-

28

LAP BELT OUTER ANCHOR COVER

73233

-

-

-

29

FRONT SEAT OUTER BELT ASSEMBLY RH

73210

-

-

-

30

CENTER PILLAR LOWER GARNISH RH

62413A

-

-

-

31

CENTER PILLAR GARNISH ASSEMBLY RH

62410A

-

-

-

*A

for RH Side

*B

for HEV Model

●

Non-reusable part

-

-

Procedure

Part Name Code

32

REAR SEATBACK HINGE SUB-ASSEMBLY LH

71304C

-

-

-

33

REAR SEAT SIDE GARNISH LH

62552F

-

-

34

LUGGAGE HOLD BELT STRIKER ASSEMBLY

58460D

-

-

-

35

LUGGAGE HOLD BELT STRIKER ASSEMBLY

58460D

-

-

-

36

REAR DECK TRIM COVER

64716D

-

-

-

37

DECK TRIM SIDE PANEL ASSEMBLY LH

64740C

-

-

38

ROOF SIDE INNER GARNISH ASSEMBLY LH

62480A

-

-

-

*A

for LH Side

*B

for Rear Side

Procedure

Part Name Code

39

REAR SEATBACK HINGE SUB-ASSEMBLY RH

71303C

-

-

-

40

REAR SEAT SIDE GARNISH RH

62551F

-

-

41

LUGGAGE HOLD BELT STRIKER ASSEMBLY

58460D

-

-

-

42

NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY

81330

-

-

43

DECK TRIM SIDE PANEL ASSEMBLY RH

64730B

-

-

44

ROOF SIDE INNER GARNISH ASSEMBLY RH

62470A

-

-

-

*A

for RH Side

-

-

Procedure

Part Name Code

45

VISOR ASSEMBLY LH

74320

-

-

-

46

VISOR ASSEMBLY RH

74310

-

-

-

47

ASSIST GRIP COVER

74612

-

-

48

ASSIST GRIP

-

-

-

-

49

REAR ASSIST GRIP LH

-

-

-

-

50

REAR ASSIST GRIP RH

-

-

-

-

51

MAP LIGHT ASSEMBLY

81260A

-

-

-

52

VANITY LIGHT ASSEMBLY

81340

-

-

53

SPOT LIGHT ASSEMBLY

81360T

-

-

54

NO. 2 FORWARD RECOGNITION COVER

86466E

-

-

55

NO. 1 FORWARD RECOGNITION COVER

86466D

-

-

56

RAIN SENSOR

89941

-

-

-

57

ROOF CENTER REINFORCEMENT PROTECTOR

63331C

-

-

-

58

FRONT DOOR CHECK ASSEMBLY

68610

-

-

-

*A

w/ Rain Sensor

*B

for Panoramic Moon Roof

*C

for Front Passenger Side

-

-

Procedure

Part Name Code

59

ROOF HEADLINING ASSEMBLY

-

-

-

*A

for Normal Roof

*B

for Panoramic Moon Roof

*1

VISOR HOLDER

-

-

PROCEDURE

1. REMOVE TONNEAU COVER ASSEMBLY

2. REMOVE DECK BOARD ASSEMBLY

*A

for Type A

*B

for Type B

3. REMOVE DECK FLOOR BOX RH

HINT:

As the illustration shown is an example, the actual details may differ.

(a) w/o Spare Tire:

*A

for Type A

*B

for Type B

(b) w/ Spare Tire:

4. REMOVE DECK FLOOR BOX LH

HINT:

As the illustration shown is an example, the actual details may differ.

(a) w/o Spare Tire:

*A

for Type A

*B

for Type B

(b) w/ Spare Tire:

5. REMOVE BATTERY SERVICE HOLE COVER ASSEMBLY (w/ Battery Cover)

HINT:

As the illustration shown is an example, the actual details may differ.

Place Hand Here

Remove in this Direction (1)

Remove in this Direction (2)

-

-

6. REMOVE FRONT SEAT ASSEMBLY LH

(a) for Manual Seat:

Click here

(b) for Power Seat:

Click here

7. REMOVE FRONT SEAT ASSEMBLY RH

(a) Use the same procedure as for the LH side.

8. REMOVE REAR SEAT ASSEMBLY

Click here

9. REMOVE REAR CONSOLE BOX ASSEMBLY

Click here

10. REMOVE FRONT DOOR SCUFF PLATE LH

Place Hand Here

Remove in this Direction (1)

Remove in this Direction (2)

-

-

11. REMOVE COWL SIDE TRIM BOARD LH

Remove in this Direction

-

-

12. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Click here

13. REMOVE FRONT PILLAR GARNISH LH

*1

Roof Headlining Assembly

*2

Front Pillar Garnish Clip

Pull in this Direction

-

-

(1) Pull the upper part of the front pillar garnish LH toward the inside of the cabin as shown in the illustration to disengage the front pillar garnish LH from the base of the 2 front pillar garnish clips.

HINT:

  • Let the front pillar garnish LH hang from the 2 front pillar garnish clips.
  • Separate the front pillar garnish LH in such a way that the front pillar garnish clip does not contact the roof headlining assembly.

Pull in this Direction

Pull in this Direction

(1) Pull down the front pillar garnish clip while pushing the side of the release lever with SST as shown in the illustration.

SST: 09813-00020

(2) While pulling the front pillar garnish clip, push the side of the release lever with SST as shown in the illustration and then separate the front pillar garnish clip from the Toyota Prius vehicle body.

Remove in this Direction

-

-

(1) Disengage the 2 guides to remove the front pillar garnish LH as shown in the illustration.

(1) Protect the curtain shield airbag assembly LH.

1. Cover the curtain shield airbag assembly LH with a protective cover, such as a cloth, and secure the edges of the cover with tape as shown in the illustration.

NOTICE:

Cover the curtain shield airbag assembly LH with a protective cover as soon as the front pillar garnish LH is removed.

(1) Remove the 2 front pillar garnish clips from the front pillar garnish LH.

14. REMOVE REAR DOOR SCUFF PLATE INSIDE LH

Place Hand Here

Remove in this Direction

Place Hand Here

Remove in this Direction

Remove in this Direction

-

-

15. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

Click here

16. REMOVE REAR UNDER SIDE COVER LH (for HEV Model)

Remove in this Direction

-

-

17. REMOVE LAP BELT OUTER ANCHOR COVER (for LH Side)

Click here

18. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

Click here

19. REMOVE CENTER PILLAR LOWER GARNISH LH

Place Hand Here

Remove in this Direction

20. REMOVE CENTER PILLER GARNISH ASSEMBLY LH

Remove in this Direction

-

-

21. REMOVE FRONT DOOR SCUFF PLATE RH

(a) Use the same procedure as for the LH side.

22. REMOVE COWL SIDE TRIM BOARD RH

(a) Use the same procedure as for the LH side.

23. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

(a) Use the same procedure as for the LH side.

24. REMOVE FRONT PILLAR GARNISH RH

(a) Use the same procedure as for the LH side.

25. REMOVE REAR DOOR SCUFF PLATE INSIDE RH

(a) Use the same procedure as for the LH side.

26. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

(a) Use the same procedure as for the LH side.

27. REMOVE REAR UNDER SIDE COVER RH (for HEV Model)

(a) Use the same procedure as for the LH side.

28. REMOVE LAP BELT OUTER ANCHOR COVER (for RH Side)

(a) Use the same procedure as for the LH side.

29. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

(a) Use the same procedure as for the LH side.

30. REMOVE CENTER PILLAR LOWER GARNISH RH

(a) Use the same procedure as for the LH side.

31. REMOVE CENTER PILLAR GARNISH ASSEMBLY RH

(a) Use the same procedure as for the LH side.

32. REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY LH

33. REMOVE REAR SEAT SIDE GARNISH LH

(1) Remove the bolt.

Place Hand Here

Remove in this Direction (1)

Remove in this Direction (2)

-

-

(1) Disengage the claw as shown in the illustration.

(2) Disengage the claw and guide.

(1) Disengage the clamp.

(2) Disconnect the airbag connector to remove the rear seat side garnish LH.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.

HINT:

Refer to How to Connect or Disconnect Airbag Connector.

Click here

34. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY (for LH Side)

35. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY (for Rear Side)

36. REMOVE REAR DECK TRIM COVER

37. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH

(1) Perform the following procedure to remove the deck trim side panel assembly LH.

1. Disengage the 2 clips.

2. Disengage the 7 claws and guide as shown in the illustration.

(2) w/ Power Outlet Socket:

1. Disconnect the connector.

38. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH

Remove in this Direction

-

-

39. REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY RH

(a) Use the same procedure as for the LH side.

40. REMOVE REAR SEAT SIDE GARNISH RH

(a) Use the same procedure as for the LH side.

41. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY (for RH Side)

(a) Use the same procedure as for the LH side.

42. REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY

Click here

43. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH

(a) Use the same procedure as for the LH side.

44. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH

(a) Use the same procedure as for the LH side.

45. REMOVE VISOR ASSEMBLY LH

46. REMOVE VISOR ASSEMBLY RH

(a) Use the same procedure as for the LH side.

47. REMOVE ASSIST GRIP COVER

*a

30 to 45°

-

-

Remove in this Direction

-

-

(1) Insert SST into the cutout of the assist grip cover as shown in the illustration.

SST: 09813-00010

NOTICE:

To prevent the assist grip assembly from being damaged, make sure to insert SST straight into the cutout.

(2) Pull SST as shown in the illustration to disengage the claw.

NOTICE:

To prevent the assist grip assembly from being damaged, make sure to only pull SST as shown in the illustration.

HINT:

Use the same procedure for the claw on the other side of the assist grip cover.

(3) Remove the assist grip cover.

(b) Use the same procedure for all assist grip covers.

48. REMOVE ASSIST GRIP

*A

for LH Side

*B

for RH Side

Remove in this Direction

-

-

49. REMOVE REAR ASSIST GRIP LH

(a) Use the same procedure as for the assist grip.

50. REMOVE REAR ASSIST GRIP RH

(a) Use the same procedure as for the assist grip.

51. REMOVE MAP LIGHT ASSEMBLY

Click here

52. REMOVE VANITY LIGHT ASSEMBLY

Click here

53. REMOVE SPOT LIGHT ASSEMBLY

Click here

54. REMOVE NO. 2 FORWARD RECOGNITION COVER

Click here

55. REMOVE NO. 1 FORWARD RECOGNITION COVER

Click here

56. REMOVE RAIN SENSOR (w/ Rain Sensor)

Click here

57. REMOVE ROOF CENTER REINFORCEMENT PROTECTOR (for Panoramic Moon Roof)

58. DISCONNECT FRONT DOOR CHECK ASSEMBLY (for Front Passenger Side)

59. REMOVE ROOF HEADLINING ASSEMBLY

HINT:

As the illustration shown is an example, the actual details may differ.

(1) for Front Pillar LH Side:

1. Remove the protective cover.

2. Disconnect each connector.

3. Disengage the 3 clamps.

4. Install the protective cover.

(2) for Front Pillar RH Side:

1. Remove the protective cover.

2. Disconnect each connector.

3. Disengage the 2 clamps.

4. Install the protective cover.

(3) for Windshield Glass Side:

1. Disconnect each connector.

(4) for Map Light Side:

1. Disconnect the connector.

(5) for Rear Pillar LH Side:

1. Disconnect the connector.

(6) for Rear Pillar RH Side:

1. Disconnect each connector.

2. Disengage the clamp.

Rotation Direction

Remove in this Direction (1)

Remove in this Direction (2)

-

-

(1) Turn each visor holder approximately 45° and remove them as indicated by the arrows, in the order shown in the illustration.

(2) Disengage the 4 claws as shown in the illustration to remove the base of each visor holder.

(c) for Normal Roof:

Remove in this Direction

-

-

(1) Disengage the 2 clips to remove the roof headlining assembly.

(2) Remove the roof headlining assembly from the Toyota Prius vehicle through the front passenger side as shown in the illustration.

NOTICE:

Do not damage the roof headlining assembly or vehicle interior.

(d) for Panoramic Moon Roof:

*a

Fastener

-

-

Remove in this Direction

-

-

(1) Disengage the 2 clips.

(2) Disengage the 12 fasteners to remove the roof headlining assembly.

(3) Remove the roof headlining assembly from the Toyota Prius vehicle through the front passenger side as shown in the illustration.

NOTICE:

Do not damage the roof headlining assembly or vehicle interior.

Disassembly

DISASSEMBLY

COMPONENTS (DISASSEMBLY)

Procedure

Part Name Code

1

TELEPHONE MICROPHONE ASSEMBLY

86730A

-

-

-

Procedure

Part Name Code

2

MICROPHONE CASE

86255F

-

-

-

Procedure

Part Name Code

3

NO. 1 ROOF SILENCER PAD

63341

-

-

-

4

NO. 2 ROOF SILENCER PAD

63342

-

-

-

5

FRONT SIDE RAIL SPACER LH

66423

-

-

-

6

FRONT SIDE RAIL SPACER RH

66413B

-

-

-

7

NO. 2 ROOF HEADLINING SET PLATE LH

63368B

-

-

-

8

NO. 2 ROOF HEADLINING SET PLATE RH

63367B

-

-

-

9

NO. 2 ROOF HEADLINING PAD

63352D

-

-

-

10

ROOF HEADLINING PAD

63351B

-

-

-

11

ROOF HEADLINING PAD LH

63356B

-

-

-

12

ROOF HEADLINING PAD RH

63355C

-

-

-

*A

for Normal Roof

-

-

Procedure

Part Name Code

13

NO. 1 ROOF WIRE

82171

-

-

14

NO. 3 ANTENNA CORD SUB-ASSEMBLY

86101D

-

-

-

*A

for Normal Roof

*B

for Panoramic Moon Roof

PROCEDURE

1. REMOVE TELEPHONE MICROPHONE ASSEMBLY

Click here

2. REMOVE MICROPHONE CASE

(b) Use the same procedure for all microphone cases.

3. REMOVE NO. 1 ROOF SILENCER PAD (for Normal Roof)

4. REMOVE NO. 2 ROOF SILENCER PAD (for Normal Roof)

5. REMOVE FRONT SIDE RAIL SPACER LH (for Normal Roof)

6. REMOVE FRONT SIDE RAIL SPACER RH (for Normal Roof)

(a) Use the same procedure as for the LH side.

7. REMOVE NO. 2 ROOF HEADLINING SET PLATE LH

8. REMOVE NO. 2 ROOF HEADLINING SET PLATE RH

(a) Use the same procedure as for the LH side.

9. REMOVE NO. 2 ROOF HEADLINING PAD (for Normal Roof)

10. REMOVE ROOF HEADLINING PAD (for Normal Roof)

(a) Use the same procedure as for the No. 2 roof headlining pad.

11. REMOVE ROOF HEADLINING PAD LH

12. REMOVE ROOF HEADLINING PAD RH

(a) Use the same procedure as for the LH side.

13. REMOVE NO. 1 ROOF WIRE

*A

for LH side

*B

for RH side

Rotation Direction

-

-

(1) Turn the 2 visor connectors approximately 90° counterclockwise and remove them from the roof headlining assembly.

(b) for Normal Roof:

(1) Remove the adhesive tape and No. 1 roof wire from the roof headlining assembly.

(c) for Panoramic Moon Roof:

(1) Remove the adhesive tape and No. 1 roof wire from the roof headlining assembly.

14. REMOVE NO. 3 ANTENNA CORD SUB-ASSEMBLY

Click here

Reassembly

REASSEMBLY

COMPONENTS (REASSEMBLY)

Procedure

Part Name Code

1

NO. 3 ANTENNA CORD SUB-ASSEMBLY

86101D

-

-

2

NO. 1 ROOF WIRE

82171

-

-

*A

for Normal Roof

*B

for Panoramic Moon Roof

Procedure

Part Name Code

3

ROOF HEADLINING PAD LH

63356B

-

-

4

ROOF HEADLINING PAD RH

63355C

-

-

5

NO. 2 ROOF HEADLINING PAD

63352D

-

-

6

ROOF HEADLINING PAD

63351B

-

-

7

NO. 2 ROOF HEADLINING SET PLATE LH

63368B

-

-

8

NO. 2 ROOF HEADLINING SET PLATE RH

63367B

-

-

9

FRONT SIDE RAIL SPACER LH

66423

-

-

10

FRONT SIDE RAIL SPACER RH

66413B

-

-

11

NO. 2 ROOF SILENCER PAD

63342

-

-

12

NO. 1 ROOF SILENCER PAD

63341

-

-

*A

for Normal Roof

-

-

Procedure

Part Name Code

13

MICROPHONE CASE

86255F

-

-

-

Procedure

Part Name Code

14

TELEPHONE MICROPHONE ASSEMBLY

86730A

-

-

-

PROCEDURE

1. INSTALL NO. 3 ANTENNA CORD SUB-ASSEMBLY

Click here

2. INSTALL NO. 1 ROOF WIRE

(a) for Normal Roof:

*a

Marking Tape

-

-

Adjustment Area

-

-

(1) 1. Engage the clamp.

2. Align the marking tape on the No. 1 roof wire with the Toyota Prius vehicle front side tab of the roof headlining assembly.

NOTICE:

  • Securely attach the No. 1 roof wire.
  • If any of the No. 1 roof wire is left loose, it will cause an abnormal noise.
  • Make sure to attach the No. 1 roof wire without leaving any of it loose.

HINT:

Secure the extra length of the No. 1 roof wire in the adjustment area.

*1

No. 1 Roof Wire

-

-

*a

Marking

*b

Correct

*c

Incorrect

*d

10 mm (0.394 in.) or more

Adhesive Tape

-

-

(2) 1. Install the No. 1 roof wire to the roof headlining assembly with adhesive tape.

Adhesive Tape Size

Area

Dimension

Area

Dimension

A

20 mm (0.787 in.)

B

80 mm (3.15 in.)

NOTICE:

  • Apply the tape securely in place.
  • Do not touch the adhesive surface when applying the tape to prevent adhesion failure.

(b) for Panoramic Moon Roof:

*a

Marking Tape

-

-

Adjustment Area

-

-

(1) 1. Engage the clamp.

2. Align the marking tape on the No. 1 roof wire with the Toyota Prius vehicle front side tab of the roof headlining assembly.

NOTICE:

  • Securely attach the No. 1 roof wire.
  • If any of the No. 1 roof wire is left loose, it will cause an abnormal noise.
  • Make sure to attach the No. 1 roof wire without leaving any of it loose.

HINT:

Secure the extra length of the No. 1 roof wire in the adjustment area.

*1

No. 1 Roof Wire

-

-

*a

Marking

*b

Correct

*c

Incorrect

*d

10 mm (0.394 in.) or more

Adhesive Tape

-

-

(2) 1. Install the No. 1 roof wire to the roof headlining assembly with adhesive tape.

Adhesive Tape Size

Area

Dimension

Area

Dimension

A

20 mm (0.787 in.)

B

80 mm (3.15 in.)

NOTICE:

  • Apply the tape securely in place.
  • Do not touch the adhesive surface when applying the tape to prevent adhesion failure.

*A

for LH side

*B

for RH side

Rotation Direction

-

-

(1) Turn the 2 visor connectors clockwise approximately 90° to install them to the roof headlining assembly.

3. INSTALL ROOF HEADLINING PAD LH

*a

Hot-melt Glue

*b

Marking

(1) Align the roof headlining pad LH with the markings on the roof headlining assembly and install it using hot-melt glue as shown in the illustration.

4. INSTALL ROOF HEADLINING PAD RH

(a) Use the same procedure as for the LH side.

5. INSTALL NO. 2 ROOF HEADLINING PAD (for Normal Roof)

*a

Hot-melt Glue

*b

Marking

(1) Align the No. 2 roof headlining pad with the markings on the roof headlining assembly and install it using hot-melt glue as shown in the illustration.

6. INSTALL ROOF HEADLINING PAD (for Normal Roof)

(a) Use the same procedure as for the No. 2 roof headlining pad.

7. INSTALL NO. 2 ROOF HEADLINING SET PLATE LH

*a

Hot-melt Glue

*b

Marking

(1) Align the No. 2 roof headlining set plate LH with the markings on the roof headlining assembly and install it using hot-melt glue as shown in the illustration.

8. INSTALL NO. 2 ROOF HEADLINING SET PLATE RH

(a) Use the same procedure as for the LH side.

9. INSTALL FRONT SIDE RAIL SPACER LH (for Normal Roof)

*a

Hot-melt Glue

*b

Marking

(1) Align the front side rail spacer LH with the markings on the roof headlining assembly and install it using hot-melt glue as shown in the illustration.

10. INSTALL FRONT SIDE RAIL SPACER RH (for Normal Roof)

(a) Use the same procedure as for the LH side.

11. INSTALL NO. 2 ROOF SILENCER PAD (for Normal Roof)

*a

Hot-melt Glue

*b

Marking

(1) Align the No. 2 roof silencer pad with the markings on the roof headlining assembly and install it using hot-melt glue as shown in the illustration.

12. INSTALL NO. 1 ROOF SILENCER PAD (for Normal Roof)

*a

Hot-melt Glue

*b

Marking

(1) Align the No. 1 roof silencer pad with the markings on the roof headlining assembly and install it using hot-melt glue as shown in the illustration.

13. INSTALL MICROPHONE CASE

14. INSTALL TELEPHONE MICROPHONE ASSEMBLY

Installation

INSTALLATION

COMPONENTS (INSTALLATION)

Procedure

Part Name Code

1

ROOF HEADLINING ASSEMBLY

-

-

-

*A

for Normal Roof

*B

for Panoramic Moon Roof

*1

VISOR HOLDER

-

-

Procedure

Part Name Code

2

FRONT DOOR CHECK ASSEMBLY

68610

-

-

-

3

ROOF CENTER REINFORCEMENT PROTECTOR

63331C

-

-

-

4

RAIN SENSOR

89941

-

-

-

5

NO. 1 FORWARD RECOGNITION COVER

86466D

-

-

-

6

NO. 2 FORWARD RECOGNITION COVER

86466E

-

-

-

7

SPOT LIGHT ASSEMBLY

81360T

-

-

-

8

VANITY LIGHT ASSEMBLY

81340

-

-

-

9

MAP LIGHT ASSEMBLY

81260A

-

-

-

10

ASSIST GRIP ASSEMBLY

74610E

-

-

11

REAR ASSIST GRIP ASSEMBLY LH

74610E

-

-

12

REAR ASSIST GRIP ASSEMBLY RH

74610E

-

-

13

VISOR ASSEMBLY LH

74320

-

-

-

14

VISOR ASSEMBLY RH

74310

-

-

-

*A

w/ Rain Sensor

*B

for Panoramic Moon Roof

*C

for Front Passenger Side

-

-

N*m (kgf*cm, ft.*lbf): Specified torque

-

-

Procedure

Part Name Code

15

ROOF SIDE INNER GARNISH ASSEMBLY LH

62480A

-

-

-

16

DECK TRIM SIDE PANEL ASSEMBLY LH

64740C

-

-

-

17

LUGGAGE HOLD BELT STRIKER ASSEMBLY

58460D

-

-

-

18

REAR SEAT SIDE GARNISH LH

62552F

-

-

19

REAR SEATBACK HINGE SUB-ASSEMBLY LH

71304C

-

-

-

*A

for LH Side

-

-

Tightening torque for "Major areas involving basic Toyota Prius vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf)

-

-

Procedure

Part Name Code

20

ROOF SIDE INNER GARNISH ASSEMBLY RH

62470A

-

-

-

21

DECK TRIM SIDE PANEL ASSEMBLY RH

64730B

-

-

-

22

REAR DECK TRIM COVER

64716D

-

-

-

23

LUGGAGE HOLD BELT STRIKER ASSEMBLY

58460D

-

-

-

24

LUGGAGE HOLD BELT STRIKER ASSEMBLY

58460D

-

-

-

25

NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY

81330

-

-

-

26

REAR SEAT SIDE GARNISH RH

62551F

-

-

27

REAR SEATBACK HINGE SUB-ASSEMBLY RH

71303C

-

-

-

*A

for RH Side

*B

for Rear Side

Tightening torque for "Major areas involving basic Toyota Prius vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf)

-

-

Procedure

Part Name Code

28

CENTER PILLER GARNISH ASSEMBLY LH

62420A

-

-

-

29

CENTER PILLAR LOWER GARNISH LH

62414A

-

-

-

30

FRONT SEAT OUTER BELT ASSEMBLY LH

73220

-

-

-

31

LAP BELT OUTER ANCHOR COVER

73233

-

-

-

32

REAR UNDER SIDE COVER LH

76974E

-

-

-

33

REAR DOOR OPENING TRIM WEATHERSTRIP LH

62332A

-

-

34

REAR DOOR SCUFF PLATE INSIDE LH

67918F

-

-

-

35

FRONT PILLAR GARNISH LH

62212

-

-

36

FRONT DOOR OPENING TRIM WEATHERSTRIP LH

62312B

-

-

37

COWL SIDE TRIM BOARD LH

62112

-

-

-

38

FRONT DOOR SCUFF PLATE LH

67914

-

-

-

*A

for LH Side

*B

for HEV Model

●

Non-reusable part

-

-

Tightening torque for "Major areas involving basic Toyota Prius vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf)

-

-

Procedure

Part Name Code

39

CENTER PILLAR GARNISH ASSEMBLY RH

62410A

-

-

-

40

CENTER PILLAR LOWER GARNISH RH

62413A

-

-

-

41

FRONT SEAT OUTER BELT ASSEMBLY RH

73210

-

-

-

42

LAP BELT OUTER ANCHOR COVER

73233

-

-

-

43

REAR UNDER SIDE COVER RH

76973E

-

-

-

44

REAR DOOR OPENING TRIM WEATHERSTRIP RH

62331A

-

-

45

REAR DOOR SCUFF PLATE INSIDE RH

67917F

-

-

-

46

FRONT PILLAR GARNISH RH

62211

-

-

47

FRONT DOOR OPENING TRIM WEATHERSTRIP RH

62311B

-

-

48

COWL SIDE TRIM BOARD RH

62111C

-

-

-

49

FRONT DOOR SCUFF PLATE RH

67913

-

-

-

*A

for RH Side

*B

for HEV Model

●

Non-reusable part

-

-

Tightening torque for "Major areas involving basic Toyota Prius vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf)

-

-

Procedure

Part Name Code

50

REAR CONSOLE BOX ASSEMBLY

-

-

-

-

51

REAR SEAT ASSEMBLY

-

-

-

-

52

FRONT SEAT ASSEMBLY LH

-

-

-

-

53

FRONT SEAT ASSEMBLY RH

-

-

-

-

Procedure

Part Name Code

54

BATTERY SERVICE HOLE COVER ASSEMBLY

58440

-

-

-

55

DECK FLOOR BOX LH

64997

-

-

-

56

DECK FLOOR BOX RH

64995

-

-

-

57

DECK BOARD ASSEMBLY

58410B

-

-

-

58

TONNEAU COVER ASSEMBLY

64910J

-

-

-

*A

for Type A

*B

for Type B

*C

w/o Spare Tire

*D

w/ Spare Tire

*E

w/ Battery Cover

-

-

*a

HINT:

As the illustration shown is an example, the actual details may differ.

-

-

PROCEDURE

1. INSTALL ROOF HEADLINING ASSEMBLY

(a) for Normal Roof:

Install in this Direction

-

-

(1) Put the roof headlining assembly into the Toyota Prius vehicle through the for front passenger side as shown in the illustration.

NOTICE:

Do not damage the roof headlining assembly or vehicle interior.

(2) Engage the 4 claws to install the base of each visor holder.

(3) Install the 2 visor holders as shown in the illustration.

(4) Engage the 2 clips to install the roof headlining assembly.

(b) for Panoramic Moon Roof:

*a

Fastener

-

-

Install in this Direction

-

-

(1) Put the roof headlining assembly into the Toyota Prius vehicle through the for front passenger side as shown in the illustration.

NOTICE:

Do not damage the roof headlining assembly or vehicle interior.

(2) Engage the 4 claws to install the base of each visor holder.

(3) Install the 2 visor holders as shown in the illustration.

(4) Engage the 12 fasteners and 2 clips to install the roof headlining assembly.

HINT:

As the illustration shown is an example, the actual details may differ.

(1) for Front Pillar LH Side:

1. Remove the protective cover.

2. Engage the 3 clamps.

3. Connect each connector.

4. Install the protective cover.

(2) for Front Pillar RH Side:

1. Remove the protective cover.

2. Engage the 2 clamps.

3. Connect each connector.

4. Install the protective cover.

(3) for Windshield Glass Side:

1. Connect each connector.

(4) for Map Light Side:

1. Connect the connector.

(5) for Rear Pillar LH Side:

1. Connect the connector.

(6) for Rear Pillar RH Side:

1. Engage the clamp.

2. Connect each connector.

2. CONNECT FRONT DOOR CHECK ASSEMBLY (for Front Passenger Side)

Torque:

30 N·m {306 kgf·cm, 22 ft·lbf}

3. INSTALL ROOF CENTER REINFORCEMENT PROTECTOR (for Panoramic Moon Roof)

4. INSTALL RAIN SENSOR (w/ Rain Sensor)

Click here

5. INSTALL NO. 1 FORWARD RECOGNITION COVER

6. INSTALL NO. 2 FORWARD RECOGNITION COVER

7. INSTALL SPOT LIGHT ASSEMBLY

8. INSTALL VANITY LIGHT ASSEMBLY

9. INSTALL MAP LIGHT ASSEMBLY

10. INSTALL ASSIST GRIP ASSEMBLY

(1) Install the 2 clips to the assist grip assembly.

(2) Temporarily install the assist grip cover LH and assist grip cover RH to the assist grip assembly as shown in the illustration.

(b) Use the same procedure for all assist grip assemblies.

*A

for LH Side

*B

for RH Side

Install in this Direction

-

-

(1) Engage the 4 clips to install the assist grip assembly as shown in the illustration.

*A

for LH Side

*B

for RH Side

(1) Engage the 8 claws to install the assist grip cover LH and assist grip cover RH.

NOTICE:

Make sure that the clips are engaged securely.

11. INSTALL REAR ASSIST GRIP ASSEMBLY LH

(a) Use the same procedure as for the assist grip assembly.

12. INSTALL REAR ASSIST GRIP ASSEMBLY RH

(a) Use the same procedure as for the assist grip assembly.

13. INSTALL VISOR ASSEMBLY LH

14. INSTALL VISOR ASSEMBLY RH

15. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY LH

16. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH

17. INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY (for LH Side)

18. INSTALL REAR SEAT SIDE GARNISH LH

(1) Connect the airbag connector to the rear seat side garnish LH.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.

HINT:

Refer to How to Connect or Disconnect Airbag Connector.

Click here

(2) Engage the clamp.

Install in this Direction

-

-

(1) Engage the guide and claw.

(1) Install the rear seat side garnish LH with the bolt.

Torque:

16 N·m {163 kgf·cm, 12 ft·lbf}

19. INSTALL REAR SEATBACK HINGE SUB-ASSEMBLY LH

Torque:

18,1 N·m {185 kgf·cm, 13 ft·lbf}

20. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY RH

21. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH

22. INSTALL REAR DECK TRIM COVER

23. INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY (for Rear Side)

24. INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY (for RH Side)

25. INSTALL NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY

26. INSTALL REAR SEAT SIDE GARNISH RH

(a) Use the same procedure as for the LH side.

27. INSTALL REAR SEATBACK HINGE SUB-ASSEMBLY RH

(a) Use the same procedure as for the LH side.

28. INSTALL CENTER PILLER GARNISH ASSEMBLY LH

29. INSTALL CENTER PILLAR LOWER GARNISH LH

30. CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

Click here

31. INSTALL LAP BELT OUTER ANCHOR COVER (for LH Side)

32. INSTALL REAR UNDER SIDE COVER LH (for HEV Model)

33. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

Click here

34. INSTALL REAR DOOR SCUFF PLATE INSIDE LH

35. INSTALL FRONT PILLAR GARNISH LH

(1) Remove the protective cover.

(1) Install 2 new front pillar garnish clips to the front pillar garnish LH.

HINT:

Make sure that the front pillar garnish clip is engaged correctly.

Install in this Direction

-

-

(1) Push the front pillar garnish LH as shown in the illustration to engage the 2 guides.

*1

Roof Headlining Assembly

*2

Front Pillar Garnish Clip

Install in this Direction

-

-

(1) Engage the 2 front pillar garnish clips to install the front pillar garnish LH as shown in the illustration.

HINT:

  • Make sure that the curtain shield airbag assembly LH is not pinched.
  • Install the front pillar garnish LH in such a way that the front pillar garnish clip does not contact the roof headlining assembly.

36. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Click here

37. INSTALL COWL SIDE TRIM BOARD LH

38. INSTALL FRONT DOOR SCUFF PLATE LH

39. INSTALL CENTER PILLAR GARNISH ASSEMBLY RH

40. INSTALL CENTER PILLAR LOWER GARNISH RH

41. CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

(a) Use the same procedure as for the LH side.

42. INSTALL LAP BELT OUTER ANCHOR COVER (for RH Side)

43. INSTALL REAR UNDER SIDE COVER RH (for HEV Model)

44. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

(a) Use the same procedure as for the LH side.

45. INSTALL REAR DOOR SCUFF PLATE INSIDE RH

46. INSTALL FRONT PILLAR GARNISH RH

(a) Use the same procedure as for the LH side.

47. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

(a) Use the same procedure as for the LH side.

48. INSTALL COWL SIDE TRIM BOARD RH

49. INSTALL FRONT DOOR SCUFF PLATE RH

50. INSTALL REAR CONSOLE BOX ASSEMBLY

Click here

51. INSTALL REAR SEAT ASSEMBLY

Click here

52. INSTALL FRONT SEAT ASSEMBLY LH

(a) for Manual Seat:

Click here

(b) for Power Seat:

Click here

53. INSTALL FRONT SEAT ASSEMBLY RH

(a) Use the same procedure as for the LH side.

54. INSTALL BATTERY SERVICE HOLE COVER ASSEMBLY (w/ Battery Cover)

55. INSTALL DECK FLOOR BOX LH

56. INSTALL DECK FLOOR BOX RH

57. INSTALL DECK BOARD ASSEMBLY

58. INSTALL TONNEAU COVER ASSEMBLY