Inverter With Converter (for Hev Model)

In this manual: Inverter With Converter (for Hev Model)
How To Troubleshoot Ecu Controlled Systems — 1How To Use This Manual — 1Identification Information — 1Repair Instruction — 1Terms — 12zr-fxe Air Cleaner Filter Element — 12zr-fxe Auxiliary Battery — 12zr-fxe Coolant (for Engine Coolant) — 12zr-fxe Oil And Oil Filter — 12zr-fxe Spark Plug — 1Air Conditioning Filter — 1Battery Cooling Filter — 1Brake Fluid — 1Coolant (for Inverter) — 1Front Brake Flexible Hose — 1Front Disc Brake Pad — 1Front Lower Ball Joint — 1Front Wheel Alignment — 1Front Wiper Rubber — 1General Maintenance — 1M20a-fxs Air Cleaner Filter Element — 1M20a-fxs Auxiliary Battery — 1M20a-fxs Coolant (for Engine Coolant) — 1M20a-fxs Oil And Oil Filter — 1M20a-fxs Spark Plug — 1Pa10/pb10/pb12 Hybrid Transaxle Fluid — 1Q810 Hybrid Transaxle Fluid — 1Rear Brake Flexible Hose — 1Rear Disc Brake Pad — 1Rear Wheel Alignment — 1Steering Column — 1Tire And Wheel — 1Transmitter Battery — 1When Disconnecting Or Reconnecting Battery Terminal — 1When Replacing Or Removing/installing Parts — 1Automatic High Beam Main Switch — 1Automatic High Beam System — 1Driver Monitor Camera — 1Driver Monitor Camera System — 1Driver Monitor Ecu — 1Front Camera — 1Front Camera System — 1Front Radar Sensor System — 1Front Side Radar Sensor — 1Front Side Radar Sensor System — 1Millimeter Wave Radar Sensor — 1Utility — 1Advanced Park — 1Advanced Park Main Switch — 1Amplifier Antenna — 1Audio And Visual System — 1Front Door Speaker — 1Instrument Panel Speaker — 1Microphone — 1Noise Filter — 1Pillar Speaker — 1Radio Antenna Cord (for Back Door) — 1Radio Antenna Cord (for Instrument Panel) — 1Radio Antenna Cord (for Roof) — 1Radio Receiver — 1Rear Door Speaker — 1Roof Antenna — 1Stereo Component Amplifier — 1Stereo Jack Adapter Assembly — 1Window Glass Antenna Wire — 1Back-up Battery — 1Dcm(telematics Transceiver) — 1Manual(sos)switch — 1Safety Connect System — 1Telephone And Gps Antenna (for Front Side) — 1Telephone And Gps Antenna (for Roof Side) — 1Telephone And Gps Antenna Cords — 1Garage Door Opener System (for Digital Inner Mirror) — 1Garage Door Opener System (for Ec Inner Mirror) — 1Blind Spot Monitor Sensor — 1Blind Spot Monitor System — 1Clearance Warning Ecu — 1Intuitive Parking Assist System — 1Panoramic View Monitor Switch — 1Panoramic View Monitor System — 1Parking Assist Ecu — 1Parking Assist Light — 1Parking Assist Monitor System — 1Parking Support Brake System — 1Rear View Monitor System — 1Television Camera (for Front) — 1Television Camera (for Rear) — 1Television Camera (for Side) — 1Ultrasonic Sensor (for Front) — 1Ultrasonic Sensor (for Rear) — 1Brake Actuator — 1Brake Pedal Stroke Sensor — 1Electronically Controlled Brake System — 1Front Speed Sensor — 1Rear Speed Sensor (for Awd) — 1Steering Angle Sensor — 1Brake Booster — 1Brake Fluid — 1Brake Line — 1Brake Pedal — 1Brake System — 1Electric Parking Brake Actuator — 1Electric Parking Brake Switch — 1Electric Parking Brake System — 1Forced Release — 1Front Axle Hub — 1Front Axle Hub Bolt — 1Rear Axle Carrier (for 2wd) — 1Rear Axle Carrier (for Awd) — 1Rear Axle Hub (for 2wd) — 1Rear Axle Hub (for Awd) — 1Rear Axle Hub Bolt — 1Steering Knuckle — 1Drive Shaft System — 1Front Drive Shaft Assembly — 1Rear Drive Shaft Assembly — 1Combination Switch — 1Electronic Shift Lever System — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Oil Seal — 1Hybrid Transaxle System — 1Input Shaft Oil Seal — 1Motor Cable — 1Pa10 Hybrid Vehicle Transaxle — 1Pa10 Manual Parking Lock Release — 1Pa10 Oil Cooler — 1Pb10/pb12 Hybrid Vehicle Transaxle — 1Pb10/pb12 Manual Parking Lock Release — 1Pb10/pb12 Oil Cooler — 1Shift Control Actuator — 1Shift Lever — 1Shift Lever Knob — 1Differential Side Gear Shaft — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Side Gear Oil Seal — 1Motor Cable — 1Rear Traction Motor — 1Coolant (for Engine) — 1Cooling Fan Motor — 1Cooling Fan System — 1Radiator — 1Relay — 1Thermostat — 1Water Pump — 1Canister — 1Egr Cooler — 1Egr Valve — 1Emission Control System — 1Fuel Tank Cap — 1Pcv Valve — 1Purge Valve — 1Vacuum Sensor — 1Air Fuel Ratio Sensor — 1Camshaft Oil Control Valve — 1Camshaft Position Sensor — 1Crankshaft Position Sensor — 1Ecm — 1Engine Coolant Temperature Sensor — 1Heated Oxygen Sensor — 1Ignition Coil And Spark Plug — 1Ignition System — 1Knock Sensor — 1Mass Air Flow Meter — 1Relay — 1Sfi System — 1Throttle Body — 1Camshaft — 1Cylinder Block — 1Cylinder Head — 1Cylinder Head Gasket — 1Engine — 1Engine Assembly — 1Engine Unit — 1Front Crankshaft Oil Seal — 1Rear Crankshaft Oil Seal — 1Fuel Filter — 1Fuel Injector — 1Fuel Pressure Regulator — 1Fuel Pump — 1Fuel Sender Gauge Assembly — 1Fuel System — 1Fuel Tank — 1Air Cleaner Filter Element — 1Exhaust Manifold — 1Exhaust Pipe — 1Intake Manifold — 1Intake System — 1Lubrication System — 1Oil And Oil Filter — 1Oil Pan And Oil Level Sensor — 1Oil Pressure Switch — 1Oil Pump — 1Accelerator Pedal Sensor — 1Battery Blower (for Hev Model) — 1Battery Ecu (for Hev Model) — 1Battery Ecu (for Phev Model) — 1Battery Voltage Sensor (for Phev Model) — 1Charge Cable (for Phev Model) — 1Charge Indicator (for Phev Model) — 1Charge Inlet (for Phev Model) — 1Combination Switch — 1Coolant (for Inverter) — 1Cooler (for Phev Model) — 1Electric Vehicle Charger Assembly (for Phev Model) — 1Frame Wire (for Hev Model) — 1Frame Wire (for Phev Model) — 1Heater Relay (for Phev Model) — 1Hv Battery (for Hev Model) — 1Hv Battery (for Phev Model) — 1Hv Battery Heater (for Phev Model) — 1Hv Battery Stack (for Phev Model) — 1Hv Relay Assembly (for Hev Model) — 1Hv Relay Assembly (for Phev Model) — 1Hybrid Battery System (for 2zr-fxe) — 1Hybrid Battery System (for M20a-fxs) — 1Hybrid Battery System (for Phev Model) — 1Hybrid Vehicle Control Ecu — 1Inverter With Converter (for Hev Model) — 1Motor Generator Control System (for 2zr-fxe) — 1Plug-in Charge Control System (for Phev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Service Plug Grip (for Hev Model) — 1Sub Radiator — 1Water Pump With Motor — 1Auxiliary Battery — 1Battery Current Sensor — 1Charging System — 1Solar Charging System — 1Solar Control Unit — 1Solar Roof — 1Can Communication System (for Hev Model) — 1Lin Communication System — 1Network Gateway Ecu — 1Integration Control Supply — 1Main Body Ecu — 1Power Integration System — 1Sub Battery System — 1Power Steering Ecu — 1Power Steering System — 1Heated Steering Wheel Controller — 1Heated Steering Wheel System — 1Steering Column Assembly — 1Steering Heater Switch — 1Steering Pad Switch — 1Steering System — 1Steering Wheel — 1Front Lower Ball Joint — 1Front Lower Suspension Arm (for 2zr-fxe Lh Side) — 1Front Lower Suspension Arm (for 2zr-fxe Rh Side) — 1Front Lower Suspension Arm (for M20a-fxs) — 1Front Shock Absorber — 1Front Stabilizer Bar — 1Front Suspension Member — 1Rear Coil Spring — 1Rear Lower Arm (for Awd Lh Side) — 1Rear Lower Arm (for Awd Rh Side) — 1Rear Lower Arm (for Hev Model 2wd) — 1Rear Lower Arm (for Phev Model) — 1Rear Shock Absorber — 1Rear Stabilizer Bar — 1Rear Suspension Member (for 2wd) — 1Rear Suspension Member (for Awd) — 1Rear Trailing Arm — 1Rear Upper Arm — 1Tire And Wheel System — 1Tire Repair Seal — 1Tire Pressure Warning Receiver — 1Tire Pressure Warning System — 1Tire Pressure Warning Valve — 1Acoustic Vehicle Alerting System — 1Vehicle Approaching Speaker — 1Vehicle Approaching Speaker Ecu — 1Back Door — 1Back Door Closer Ecu — 1Back Door Opener Switch — 1Back Door Support — 1Back Door Weatherstrip — 1Charge Lid Courtesy Switch — 1Charge Lid Opener Motor Assembly — 1Charge Lid Opener System — 1Charge Lid Opener Unit — 1Front Door — 1Front Door Opening Trim Weatherstrip — 1Fuel Lid Opener Motor Assembly — 1Fuel Lid Opener Switch — 1Fuel Lid Opener System — 1Hood — 1Hood Lock Control Cable Assembly — 1Power Back Door Closer Switch — 1Power Back Door Control Switch — 1Power Back Door Drive Unit — 1Power Back Door System — 1Power Back Door Touch Sensor — 1Power Back Door Warning Buzzer — 1Rear Door — 1Rear Door Opening Trim Weatherstrip — 1Reserve Lock Switch — 1Front Bumper — 1Front Door Belt Moulding — 1Front Door Window Frame Moulding — 1Front Fender — 1Front Pillar Upper Cover — 1Grille Shutter — 1Grille Shutter System — 1Name Plate — 1Quarter Garnish — 1Rear Bumper — 1Rear Door Belt Moulding — 1Rear Door Window Frame Moulding — 1Rear Wheel House Plate — 1Rocker Panel Moulding — 1Roof Drip Side Finish Moulding — 1Roof Garnish — 1Wheel Opening Moulding (for Front Side) — 1Wheel Opening Moulding (for Rear Side) — 1Windshield Outside Moulding — 1Horn — 1Horn System — 1Relay — 1Automatic Light Control Sensor — 1Back-up Light Assembly — 1Charge Lid Light — 1Front Marker Light — 1Hazard Warning Switch — 1Headlight Assembly — 1Headlight Dimmer Switch — 1Headlight Leveling Switch — 1High Mounted Stop Light Assembly — 1Illumination Light Assembly — 1License Plate Light Assembly — 1Lighting System — 1Rear Combination Light Assembly — 1Rear Light Assembly — 1Rear Side Marker Light Assembly — 1Relay — 1Side Turn Signal Light Assembly — 1Stop Light Switch — 1Switch Housing — 1Outer Mirror Switch — 1Outer Rear View Mirror — 1Outer Rear View Mirror Cover — 1Outer Rear View Mirror Glass — 1Power Mirror Control System — 1Back Door Glass — 1Front Passenger Side Power Window Switch — 1Power Window Control System — 1Power Window Master Switch — 1Power Window Regulator Motor (for Front Door) — 1Power Window Regulator Motor (for Rear Door) — 1Rear Power Window Switch — 1Relay — 1Roof Window Fix Glass — 1Window Defogger System — 1Windshield Deicer Switch — 1Windshield Deicer System — 1Windshield Glass — 1Front Wiper Motor — 1Rain Sensor — 1Relay — 1Washer Motor — 1Washer Nozzle (for Front Side) — 1Washer Nozzle (for Rear Television Camera) — 1Wiper And Washer System — 1Wiper Ecu — 1Wiper Switch — 1Back Door Lock — 1Door Control Receiver — 1Door Control Switch — 1Door Control Transmitter — 1Door Lock Release Motor (for Rear Side) — 1Door Outside Handle (for Rear Side) — 1Front Door Lock — 1Power Door Lock Control System — 1Rear Door Lock — 1Transmitter Battery — 1Wireless Door Lock Control System — 1Accumulator — 1Air Conditioning Amplifier — 1Air Conditioning Panel — 1Air Conditioning Pressure Sensor — 1Air Conditioning Unit — 1Ambient Temperature Sensor — 1Blower Unit — 1Condenser (for Hev Model) — 1Condenser (for Phev Model) — 1Discharge Temperature Sensor — 1Electric Expansion Valve (cooling) — 1Electric Expansion Valve (heating) — 1Evaporator Pipe Temperature Sensor — 1Evaporator Pressure Regulator — 1Front Blower Motor — 1Front Evaporator Front Solenoid Valve — 1Air Conditioning System (for Hev Model) — 1Front Evaporator Temperature Sensor — 1Heat Exchanger Temperature Sensor — 1Heat Pump Ecu — 1High Pressure Magnetic Valve — 1Humidity Sensor — 1Internal Condenser Temperature Sensor — 1Low Pressure Magnetic Valve — 1Refrigerant (for Hfc-134a(r134a)) — 1Refrigerant Line (for Hev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Room Temperature Sensor — 1Solar Sensor — 1Floor Carpet — 1Front Console Box — 1Instrument Panel Safety Pad — 1Roof Headlining — 1Roof Sunshade — 1Ambient Light (for Driver Side) — 1Ambient Light (for Front Passenger Side) — 1Back Door Courtesy Switch — 1Footwell Light — 1Glove Box Light — 1Lighting System — 1Luggage Compartment Room Light — 1Personal Light — 1Room Light — 1Vanity Light — 1Vanity Light Switch — 1Combination Meter — 1Meter / Gauge System — 1Trip Switch — 1Digital Inner Mirror — 1Digital Rear-view Mirror System — 1Inner Mirror Monitor Camera — 1Inner Rear View Mirror (w/o Ec Mirror) — 1Accessory Power Outlet System — 1Power Outlet Socket (for Console Box Front Side) — 1Power Outlet Socket (for Console Box Rear Side) — 1Power Outlet Socket (for Console Box) — 1Power Outlet Socket (for Luggage Compartment) — 1Power Outlet Switch — 1Wireless Charger Assembly — 1Wireless Charging System — 1Climate Control Seat System — 1Front Power Seat Control System (w/ Memory) — 1Front Power Seat Motor Assembly — 1Front Seat Assembly (for Power Seat) — 1Front Seat Cushion Heater (for Power Seat) — 1Front Seatback Heater (for Power Seat) — 1Lumbar Support Adjuster Assembly — 1Power Seat Control Ecu — 1Power Seat Switch — 1Power Seat Track Rail Assembly — 1Rear Seat Assembly — 1Rear Seat Cushion Heater — 1Rear Seat Reminder System — 1Rear Seatback Heater — 1Seat Heater Control — 1Seat Heater Switch (for Front Seat) — 1Seat Heater Switch (for Rear Side) — 1Seat Heater System — 1Seat Memory Switch — 1Child Restraint Seat Anchor Bracket — 1Front Seat Inner Belt Assembly — 1Front Seat Outer Belt Assembly — 1Occupant Detection Sensor (for Front Passenger Side) — 1Rear Center Seat Outer Belt Assembly — 1Rear Seat Inner Belt Assembly (for Rh Side) — 1Rear Seat Outer Belt Assembly — 1Seat Belt Warning System (w/ Occupant Classification System) — 1Tongue Plate Stopper — 1Airbag System — 1Center Airbag Sensor Assembly — 1Curtain Shield Airbag Assembly — 1Front Airbag Sensor — 1Front Passenger Airbag Assembly — 1Front Seat Side Airbag Assembly — 1Inspection After Collision — 1Knee Airbag Assembly — 1Occupant Classification System — 1Rear Seat Side Airbag Assembly — 1Side Airbag Sensor (for Center Pillar) — 1Side Airbag Sensor (for Front Door) — 1Spiral Cable — 1Steering Pad — 1Certification Ecu — 1Digital Key Ecu — 1Digital Key Receiver (for Front Floor) — 1Digital Key Receiver (for Outside Luggage Compartment) — 1Digital Key Receiver (for Rear Door) — 1Digital Key System — 1Electrical Key Oscillator (for Front Floor) — 1Electrical Key Oscillator (for Outside Luggage Compartment) — 1Electrical Key Oscillator (for Rear Floor) — 1Engine Hood Courtesy Switch — 1Id Code Box — 1Smart Key System (for Start Function) — 1
~34min read
010203040504.53N·mlb·ft
Tightening torque found on this page
  • Precaution
  • Removal
  • Disassembly
  • Reassembly
  • Installation

Precaution

PRECAUTION

1.PRECAUTION WHEN REMOVING/INSTALLING INVERTER WITH CONVERTER ASSEMBLY

CAUTION:

  • Do not push down or apply excessive force to the inverter with converter assembly.
  • Be careful not to injure yourself on the edges of the inverter with converter assembly when performing work.

NOTICE:

Observe the following in order to prevent entry of foreign matter:

  • Do not allow foreign matter such as grease, oil or water to adhere to the inside of the inverter with converter assembly.
  • Do not use air tools in areas other than specified to prevent entry of dust.
  • Prevent wind from blowing through the workshop to prevent entry of dust.
  • Do not drop any bolts or tools into the inverter with converter assembly.
  • Clean the tools before use.

NOTICE:

PRECAUTION WHEN HANDLING ELECTRONIC COMPONENTS

  • Do not touch the terminals of the connectors or areas other than the specified on circuit boards, as static electricity may be applied to parts and damage them.
  • Do not drop electronic components such as circuit boards or subject them to impact.
  • Keep the removed parts free from dust.
  • Electronic components are very sensitive. Be sure to observe the handling instructions.

NOTICE:

PRECAUTION WHEN HANDLING PARTS

  • Do not drop parts or subject them to impact.
  • If a part is subject to impact, replace it with a new one.
  • Be sure to observe the handling instructions to prevent parts from being damaged.
  • Do not lower the vibration dampening connectors until the motor generator control ECU sub-assembly is installed to the inverter with converter assembly.

NOTICE:

PRECAUTION WHEN SUSPENDING WORK

  • If suspending work, cover parts with clean pieces of paper to prevent entry of dust and foreign matter.

HINT:

  • Arrange the removed parts in the correct order so that they can be installed to the correct position and with the correct orientation.
  • It is recommended to take pictures of parts before removing them to ensure correct installation.

Removal

REMOVAL

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during inverter with converter assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

Replacement of inverter with converter assembly

ECU configuration

-

Resolver learning

  • DTCs are stored
  • Slight vibration at a Toyota Prius vehicle speed of 5 km/h or less
  • Shock or vibration during acceleration

2ZR-FXE:

M20A-FXS:

CAUTION:

  • Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

    Click here

  • To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click here

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

Items for which learning is completed by driving the Toyota Prius vehicle

Effect/Inoperative Function when Necessary Procedure not Performed

Necessary Procedure

Link

Front Camera System

Drive the Toyota Prius vehicle straight ahead at 35 km/h or more for 5 seconds or more.

Items for which learning is completed by operating the vehicle normally

Effect/Inoperative Function when Necessary Procedure not Performed

Necessary Procedure

Link

*1: w/o Power Back Door System

*2: w/ Power Back Door System

Power Door Lock Control System*1

  • Back door opener

Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.

Power Back Door System*2

Reset back door close position

Air Conditioning System

After the ignition switch is turned to ON, the servo motor standard position is recognized.

-

COMPONENTS (REMOVAL)

Procedure

Part Name Code

1

PRECAUTION

-

-

-

2

SERVICE PLUG GRIP

G3834

-

-

-

3

DRAIN COOLANT

-

-

-

Procedure

Part Name Code

4

FRONT WIPER ARM HEAD CAP

85292B

-

-

5

SHIELD CAP

85247

-

-

6

FRONT WIPER ARM AND BLADE ASSEMBLY LH

-

-

-

7

FRONT WIPER ARM AND BLADE ASSEMBLY RH

-

-

-

8

WINDSHIELD LOWER OUTSIDE MOULDING LH

75536D

-

-

9

WINDSHIELD LOWER OUTSIDE MOULDING RH

75535F

-

-

-

10

COWL WATER EXTRACT SHIELD LH

55754F

-

-

-

11

COWL WATER EXTRACT SHIELD RH

55753D

-

-

-

12

COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

55708

-

-

13

CHECK TERMINAL VOLTAGE

-

-

-

*A

for M20A-FXS

*B

for 2ZR-FXE

*1

Connector Cover Assembly

-

-

N*m (kgf*cm, ft.*lbf): Specified torque

-

-

Procedure

Part Name Code

14

ECM

89661

-

-

-

Procedure

Part Name Code

15

BATTERY CLAMP SUB-ASSEMBLY

74404A

-

-

-

16

RADIATOR SUPPORT OPENING COVER

53289A

-

-

-

17

AIR CLEANER CAP SUB-ASSEMBLY

17705

-

-

-

18

AIR CLEANER HOSE ASSEMBLY

-

-

-

-

19

AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

17801

-

-

-

20

AIR CLEANER CASE SUB-ASSEMBLY

17701

-

-

-

21

INLET NO. 2 AIR CLEANER

17752

-

-

-

22

AIR CLEANER BRACKET

17771A

-

-

-

23

INLET NO. 1 AIR CLEANER

17751

-

-

-

*A

for 2ZR-FXE

-

-

Procedure

Part Name Code

24

NO. 2 VENTILATION HOSE

12262

-

-

-

25

AIR CLEANER CAP WITH AIR CLEANER HOSE

-

-

-

-

26

AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

17801

-

-

-

27

AIR CLEANER CASE SUB-ASSEMBLY

17701

-

-

-

28

AIR CLEANER BRACKET

17771A

-

-

-

29

HV AIR CONDITIONING WIRE

821H2

-

-

30

NO. 2 RELAY BLOCK COVER

82662B

-

-

-

31

NO. 3 ENGINE WIRE

82123

-

-

-

32

VACUUM SWITCHING VALVE ASSEMBLY

25860

-

-

-

*A

for M20A-FXS

-

-

Procedure

Part Name Code

33

ENGINE WIRE

82121

-

-

34

ENGINE ROOM MAIN WIRE

82111

-

-

35

FLOOR UNDER WIRE

821H1

-

-

36

NO. 7 ENGINE WIRE

82127D

-

-

37

OUTLET NO. 1 INVERTER COOLING HOSE

G922C

-

-

38

INLET NO. 1 INVERTER COOLING HOSE

G922AA

-

-

39

ENGINE WIRE

82121

-

-

*A

for 2WD

*B

for 4WD

Procedure

Part Name Code

40

SEPARATE INVERTER WITH CONVERTER ASSEMBLY

G9200

-

-

41

UPPER INVERTER COVER

G9221

-

-

42

MOTOR CABLE

G1148

-

-

43

REMOVE INVERTER WITH CONVERTER ASSEMBLY

G9200

-

-

PROCEDURE

1. PRECAUTION

Click here

2. REMOVE SERVICE PLUG GRIP

Click here

3. DRAIN COOLANT (for Inverter)

Click here

4. REMOVE FRONT WIPER ARM HEAD CAP

Click here

5. REMOVE SHIELD CAP (for M20A-FXS)

Click here

6. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

Click here

7. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

Click here

8. REMOVE WINDSHIELD LOWER OUTSIDE MOULDING LH

Click here

9. REMOVE WINDSHIELD LOWER OUTSIDE MOULDING RH

(a) Use the same procedure as for the LH side.

10. REMOVE COWL WATER EXTRACT SHIELD LH

Click here

11. REMOVE COWL WATER EXTRACT SHIELD RH

(a) Use the same procedure as for the LH side.

12. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Click here

13. CHECK TERMINAL VOLTAGE

CAUTION:

Be sure to wear insulated gloves.

(1) Remove the bolt (A).

(2) Using a T20 "TORX" socket wrench, remove the bolt (B) and connector cover assembly from the inverter with converter assembly.

NOTICE:

  • Do not touch the connector cover assembly waterproof seal.
  • Do not allow any foreign matter or water to enter the inverter with converter assembly.

*a

Terminal

-

-

(1) Using a voltmeter, measure the voltage between the terminals of the 2 phase connectors.

Standard Voltage:

0 V

NOTICE:

Do not allow any foreign matter or water to enter the inverter with converter assembly.

HINT:

  • Use a measuring range of DC 750 V or more on the voltmeter.
  • Perform the measurement while holding the tips of the tester probes against the terminals as shown in the illustration.

(1) Using a T20 "TORX" socket wrench, install the connector cover assembly to the inverter with converter assembly with the bolt (B).

Torque:

4,5 N·m {46 kgf·cm, 40 in·lbf}

NOTICE:

Do not touch the waterproof seal of the connector cover assembly.

(2) Install the bolt (A).

Torque:

8 N·m {82 kgf·cm, 71 in·lbf}

HINT:

It is not necessary to install the bolt (B) if it is to be removed in the next step or later, such as when removing the inverter with converter assembly.

14. REMOVE ECM

  • for M20A-FXS:

    Click here

  • for 2ZR-FXE:

    Click here

15. REMOVE BATTERY CLAMP SUB-ASSEMBLY (for 2ZR-FXE)

16. REMOVE RADIATOR SUPPORT OPENING COVER (for 2ZR-FXE)

Click here

17. REMOVE AIR CLEANER CAP SUB-ASSEMBLY (for 2ZR-FXE)

Click here

18. REMOVE AIR CLEANER HOSE ASSEMBLY (for 2ZR-FXE)

Click here

19. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY (for 2ZR-FXE)

Click here

20. REMOVE AIR CLEANER CASE SUB-ASSEMBLY (for 2ZR-FXE)

Click here

21. REMOVE INLET NO. 2 AIR CLEANER (for 2ZR-FXE)

Click here

22. REMOVE AIR CLEANER BRACKET (for 2ZR-FXE)

Click here

23. REMOVE INLET NO. 1 AIR CLEANER (for 2ZR-FXE)

Click here

24. DISCONNECT NO. 2 VENTILATION HOSE (for M20A-FXS)

Click here

25. REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE (for M20A-FXS)

Click here

26. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY (for M20A-FXS)

Click here

27. REMOVE AIR CLEANER CASE SUB-ASSEMBLY (for M20A-FXS)

28. REMOVE AIR CLEANER BRACKET (for M20A-FXS)

29. DISCONNECT HV AIR CONDITIONING WIRE

CAUTION:

Be sure to wear insulated gloves.

NOTICE:

  • Do not damage the terminals, connector housing or inverter with converter assembly during disconnection.
  • Insulate the disconnected terminals with insulating tape.

(a) for 2ZR-FXE:

*a

Green-colored Lock

-

-

Slide

-

-

(1) Slide the green-colored lock of the connector as shown in the illustration to release it and disconnect the HV air conditioning wire.

(b) for M20A-FXS:

*a

Green-colored Lock

-

-

Slide

-

-

(1) Disengage the 2 clamps.

(2) Slide the green-colored lock of the connector as shown in the illustration to release it and disconnect the HV air conditioning wire.

30. REMOVE NO. 2 RELAY BLOCK COVER

31. DISCONNECT NO. 3 ENGINE WIRE

32. DISCONNECT VACUUM SWITCHING VALVE ASSEMBLY NO.1

33. DISCONNECT ENGINE WIRE

CAUTION:

Be sure to wear insulated gloves.

NOTICE:

Do not allow any foreign matter or water to enter the inverter with converter assembly.

(1) Move the lock lever while pushing the lock on the connector, and disconnect the inverter with converter assembly connector.

NOTICE:

  • Do not damage the terminals, connector housing or inverter with converter assembly during disconnection.
  • Cover the hole where the cable was connected with tape (non-residue type) or equivalent to prevent entry of foreign matter.
  • Insulate the disconnected terminals with insulating tape.
  • Do not touch the waterproof seal or terminals of the connector.

34. DISCONNECT ENGINE ROOM MAIN WIRE

CAUTION:

Be sure to wear insulated gloves.

NOTICE:

Do not allow any foreign matter or water to enter the inverter with converter assembly.

(1) Move the lock lever while pushing the lock on the connector, and disconnect the inverter with converter assembly connector.

NOTICE:

  • Do not damage the terminals, connector housing or inverter with converter assembly during disconnection.
  • Cover the hole where the cable was connected with tape (non-residue type) or equivalent to prevent entry of foreign matter.
  • Insulate the disconnected terminals with insulating tape.
  • Do not touch the waterproof seal or terminals of the connector.

35. DISCONNECT FLOOR UNDER WIRE

CAUTION:

Be sure to wear insulated gloves.

NOTICE:

  • Do not allow any foreign matter or water to enter the inverter with converter assembly.
  • Do not touch the waterproof seal or terminals of the connector.
  • Do not damage the terminals, connector housing or inverter with converter assembly during disconnection.
  • Cover the hole where the cable was connected with tape (non-residue type) or equivalent to prevent entry of foreign matter.
  • Do not allow any foreign matter or water to enter the inverter with converter assembly.
  • Insulate the disconnected terminals with insulating tape.

*a

Waterproof Seal

-

-

(b) for 4WD:

*a

Waterproof Seal

-

-

36. DISCONNECT NO. 7 ENGINE WIRE

CAUTION:

Be sure to wear insulated gloves.

37. DISCONNECT OUTLET NO. 1 INVERTER COOLING HOSE

NOTICE:

Put pieces of cloth into the pipe and disconnected hose or cover the pipe and hose with plastic bags to prevent entry of foreign matter.

38. DISCONNECT INLET NO. 1 INVERTER COOLING HOSE

NOTICE:

Put pieces of cloth into the pipe and disconnected hose or cover the pipe and hose with plastic bags to prevent entry of foreign matter.

39. DISCONNECT ENGINE WIRE

CAUTION:

Be sure to wear insulated gloves.

NOTICE:

Do not allow any foreign matter or water to enter the inverter with converter assembly.

40. SEPARATE INVERTER WITH CONVERTER ASSEMBLY

CAUTION:

Be sure to wear insulated gloves.

NOTICE:

To prevent damage due to static electricity, do not touch the terminals of the disconnected connectors.

41. REMOVE UPPER INVERTER COVER

CAUTION:

Be sure to wear insulated gloves.

(1) Remove the bolt and inverter cover from the hybrid Toyota Prius vehicle transaxle assembly.

(2) To prevent the inverter with converter assembly from falling, temporarily install the bolt in the location shown in the illustration.

(3) Shift the position of the inverter with converter assembly and temporarily set it on top of the stud bolts as shown in the illustration.

NOTICE:

When lifting, make sure not to apply force to the motor cable.

(4) Loosen the 2 bolts, leaving 2 to 3 threads at the tip of the bolt still engaged.

*a

Interlock

*b

Waterproof Seal

(1) Using the 2 bolts as guides, remove the upper inverter cover from the inverter with converter assembly.

NOTICE:

  • Make sure to pull the upper inverter cover straight out, as a connector is connected to the inside of the upper inverter cover.
  • Do not touch the waterproof seal of the upper inverter cover.
  • Do not allow any foreign matter or water to enter the inverter with converter assembly.
  • When removing the upper inverter cover, do not pull the areas (A) as they may deform.
  • Make sure that the interlock is installed to the upper inverter cover.
  • Do not remove or excessively tighten the screw of the upper inverter cover.

    *1

    Inverter Cover

    *a

    Screw

  • Although the inverter cover may feel loose, this is not due to a malfunction.
  • Hold the upper inverter cover horizontal while removing it.

HINT:

If necessary, use a screwdriver with its tip wrapped with protective tape as shown in the illustration to remove the upper inverter cover.

(2) Remove the 2 bolts.

(1) Shift the position of the inverter with converter assembly and temporarily set it on the hybrid Toyota Prius vehicle transaxle assembly as shown in the illustration.

NOTICE:

When lifting, make sure not to apply force to the motor cable.

(2) Remove the bolt.

42. DISCONNECT MOTOR CABLE

CAUTION:

Be sure to wear insulated gloves.

*a

Waterproof Seal

-

-

(1) Using an insulated tool, remove the 6 bolts.

NOTICE:

  • Do not allow any foreign matter or water to enter the inverter with converter assembly.
  • Do not touch the waterproof seal or terminals of the connector.

(2) Remove the 4 bolts and disconnect the motor cable from the inverter with converter assembly.

NOTICE:

  • Do not allow any foreign matter or water to enter the inverter with converter assembly.
  • Do not touch the waterproof seal or terminals of the connector.
  • Do not damage the terminals, connector housing or inverter with converter assembly during disconnection.
  • Insulate the disconnected terminals with insulating tape.
  • Cover the hole where the cable was connected with tape (non-residue type) or equivalent to prevent entry of foreign matter.
  • To prevent the wire harness from being caught, make sure to bundle the wire harness using insulating tape or equivalent.

43. REMOVE INVERTER WITH CONVERTER ASSEMBLY

CAUTION:

Be sure to wear insulated gloves.

NOTICE:

  • When removing the inverter with converter assembly, be careful not to damage the parts around it.
  • To prevent damage, do not hold the inverter with converter assembly by the connectors, brackets or cooling pipes.
  • To prevent damage due to static electricity, do not touch the terminals of the disconnected connectors.

(1) Even after the coolant is drained, coolant remains in the inverter due to its internal structure. Therefore, seal or cover the pipes when removing the inverter with converter assembly so that coolant does not spill out.

Disassembly

DISASSEMBLY

COMPONENTS (DISASSEMBLY)

Procedure

Part Name Code

1

NO. 1 INVERTER BRACKET

G9214

-

-

2

NO. 2 INVERTER BRACKET

G9215

-

-

3

NO. 3 ENGINE WIRE

82123

-

-

4

HV AIR CONDITIONING WIRE

821H2

-

-

5

FUEL HOSE BRACKET

23881B

-

-

-

6

WIRE HARNESS CLAMP BRACKET

-

-

-

-

*A

for M20A-FXS

*B

for 2ZR-FXE

PROCEDURE

1. REMOVE NO. 1 INVERTER BRACKET

NOTICE:

Make sure to support the inverter with converter assembly at the positions shown in the illustration, otherwise it may be damaged.

  • *a: Bottom of Inverter with Converter Assembly

    *b: Support

(1) Set the inverter with converter assembly on wooden blocks.

(2) Remove the 2 bolts and No. 1 inverter bracket from the inverter with converter assembly.

NOTICE:

Do not touch portion (A) of the No. 1 inverter bracket.

2. REMOVE NO. 2 INVERTER BRACKET

(1) Remove the 2 bolts and No. 2 inverter bracket from the inverter with converter assembly.

NOTICE:

Do not touch portion (A) of the No. 2 inverter bracket.

3. REMOVE NO. 3 ENGINE WIRE

CAUTION:

Be sure to wear insulated gloves.

NOTICE:

  • Do not allow any foreign matter or water to enter the inverter with converter assembly.
  • Perform this procedure when it is necessary to replace the inverter with converter assembly or the No. 3 engine wire.

(1) Disengage the 2 claws and open the cover.

(2) Remove the bolt, nut, clamp and disconnect the No. 3 engine wire from the inverter with converter assembly.

NOTICE:

Move the tool in the downward direction to loosen the nut as shown in the illustration.

4. REMOVE HV AIR CONDITIONING WIRE

CAUTION:

Be sure to wear insulated gloves.

NOTICE:

  • Do not touch the waterproof seal or terminals of the connector.
  • Do not damage the terminals, connector housing or inverter with converter assembly during disconnection.
  • Cover the hole where the cable was connected with tape (non-residue type) or equivalent to prevent entry of foreign matter.
  • Do not allow any foreign matter or water to enter the inverter with converter assembly.
  • Insulate the disconnected terminals with insulating tape.

*a

Waterproof Seal

-

-

5. REMOVE FUEL HOSE BRACKET (for M20A-FXS)

*A

for 2WD

*B

for 4WD

6. REMOVE WIRE HARNESS CLAMP BRACKET

(a) for M20A-FXS:

*A

for 2WD

*B

for 4WD

(b) for 2ZR-FXE:

*A

for 2WD

*B

for 4WD

Reassembly

REASSEMBLY

COMPONENTS (REASSEMBLY)

Procedure

Part Name Code

1

WIRE HARNESS CLAMP BRACKET

-

-

-

-

2

FUEL HOSE BRACKET

23881B

-

-

-

3

HV AIR CONDITIONING WIRE

821H2

-

-

4

NO. 3 ENGINE WIRE

82123

-

-

5

NO. 2 INVERTER BRACKET

G9215

-

-

6

NO. 1 INVERTER BRACKET

G9214

-

-

*A

for M20A-FXS

*B

for 2ZR-FXE

Tightening torque for "Major areas involving basic Toyota Prius vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf)

N*m (kgf*cm, ft.*lbf): Specified torque

PROCEDURE

1. INSTALL WIRE HARNESS CLAMP BRACKET

(a) for M20A-FXS:

*A

for 2WD

*B

for 4WD

Torque:

Bolt A :

10 N·m {102 kgf·cm, 7 ft·lbf}

Bolt B :

8 N·m {82 kgf·cm, 71 in·lbf}

(b) for 2ZR-FXE:

*A

for 2WD

*B

for 4WD

Torque:

Bolt A :

10 N·m {102 kgf·cm, 7 ft·lbf}

Bolt B :

8 N·m {82 kgf·cm, 71 in·lbf}

2. INSTALL FUEL HOSE BRACKET (for M20A-FXS)

Torque:

13 N·m {133 kgf·cm, 10 ft·lbf}

3. INSTALL HV AIR CONDITIONING WIRE

CAUTION:

Be sure to wear insulated gloves.

NOTICE:

  • Do not allow any foreign matter or water to enter the inverter with converter assembly.
  • Do not touch the waterproof seal or terminals of the connector.
  • Do not damage the terminals, connector housing or inverter with converter assembly when connecting the connector.

*a

Waterproof Seal

-

-

Torque:

Bolt A :

8 N·m {82 kgf·cm, 71 in·lbf}

Bolt B :

10 N·m {102 kgf·cm, 7 ft·lbf}

4. INSTALL NO. 3 ENGINE WIRE

CAUTION:

Be sure to wear insulated gloves.

NOTICE:

  • Do not allow any foreign matter or water to enter the inverter with converter assembly.
  • Perform this procedure when it is necessary to replace the inverter with converter assembly and the No. 3 engine wire.

(1) Engage the clamp and connect the engine wire to the inverter with converter assembly with the bolt and nut.

Torque:

Bolt :

10 N·m {102 kgf·cm, 7 ft·lbf}

Nut :

16 N·m {163 kgf·cm, 12 ft·lbf}

NOTICE:

  • Move the tool in the downward direction to tighten the nut as shown in the illustration.
  • To avoid damaging the threads, be sure to perform the procedure by hand.

(2) Engage the 2 claws.

5. INSTALL NO. 2 INVERTER BRACKET

NOTICE:

Make sure to support the inverter with converter assembly at the positions shown in the illustration, otherwise it may be damaged.

  • *a: Bottom of Inverter with Converter Assembly

    *b: Support

(1) Set the inverter with converter assembly on wooden blocks.

(2) Temporarily install the No. 2 inverter bracket to the inverter with converter assembly with the 2 bolts.

NOTICE:

Do not touch portion (A) of the No. 2 inverter bracket.

(3) Fully tighten the 2 bolts in the order shown in the illustration.

Torque:

15 N·m {153 kgf·cm, 11 ft·lbf}

6. INSTALL NO. 1 INVERTER BRACKET

(1) Temporarily install the No. 1 inverter bracket to the inverter with converter assembly with the 2 bolts.

NOTICE:

Do not touch portion (A) of the No. 1 inverter bracket.

(2) Fully tighten the 2 bolts in the order shown in the illustration.

Torque:

15 N·m {153 kgf·cm, 11 ft·lbf}

Installation

INSTALLATION

COMPONENTS (INSTALLATION)

Procedure

Part Name Code

1

SET INVERTER WITH CONVERTER ASSEMBLY

G9200

-

-

2

MOTOR CABLE

G1148

-

-

3

UPPER INVERTER COVER

G9221

-

-

4

INSTALL INVERTER WITH CONVERTER ASSEMBLY

G9200

-

-

*

For use with a union nut wrench

-

-

Tightening torque for "Major areas involving basic Toyota Prius vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf)

N*m (kgf*cm, ft.*lbf): Specified torque

Procedure

Part Name Code

5

ENGINE WIRE

82121

-

-

6

INLET NO. 1 INVERTER COOLING HOSE

G922AA

-

-

7

OUTLET NO. 1 INVERTER COOLING HOSE

G922C

-

-

8

NO. 7 ENGINE WIRE

82127D

-

-

9

FLOOR UNDER WIRE

821H1

-

-

10

ENGINE ROOM MAIN WIRE

82111

-

-

11

ENGINE WIRE

82121

-

-

*A

for 2WD

*B

for 4WD

Tightening torque for "Major areas involving basic Toyota Prius vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf)

N*m (kgf*cm, ft.*lbf): Specified torque

Procedure

Part Name Code

12

VACUUM SWITCHING VALVE ASSEMBLY

25860

-

-

-

13

NO. 3 ENGINE WIRE

82123

-

-

-

14

NO. 2 RELAY BLOCK COVER

82662B

-

-

-

15

HV AIR CONDITIONING WIRE

821H2

-

-

16

AIR CLEANER BRACKET

17771A

-

-

-

17

AIR CLEANER CASE SUB-ASSEMBLY

17701

-

-

-

18

AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

17801

-

-

-

19

AIR CLEANER CAP WITH AIR CLEANER HOSE

-

-

-

-

20

NO. 2 VENTILATION HOSE

12262

-

-

-

*A

for M20A-FXS

-

-

Tightening torque for "Major areas involving basic Toyota Prius vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf)

N*m (kgf*cm, ft.*lbf): Specified torque

Procedure

Part Name Code

21

INLET NO. 1 AIR CLEANER

17751

-

-

-

22

AIR CLEANER BRACKET

17771A

-

-

-

23

INLET NO. 2 AIR CLEANER

17752

-

-

-

24

AIR CLEANER CASE SUB-ASSEMBLY

17701

-

-

-

25

AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

17801

-

-

-

26

AIR CLEANER HOSE ASSEMBLY

-

-

-

-

27

AIR CLEANER CAP SUB-ASSEMBLY

17705

-

-

-

28

RADIATOR SUPPORT OPENING COVER

53289A

-

-

-

29

BATTERY CLAMP SUB-ASSEMBLY

74404A

-

-

-

*A

for 2ZR-FXE

-

-

N*m (kgf*cm, ft.*lbf): Specified torque

-

-

Procedure

Part Name Code

30

ECM

89661

-

-

-

Procedure

Part Name Code

31

COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

55708

-

-

32

COWL WATER EXTRACT SHIELD LH

55754F

-

-

-

33

COWL WATER EXTRACT SHIELD RH

55753D

-

-

-

34

WINDSHIELD LOWER OUTSIDE MOULDING LH

75536D

-

-

-

35

WINDSHIELD LOWER OUTSIDE MOULDING RH

75535F

-

-

-

36

FRONT WIPER ARM AND BLADE ASSEMBLY LH

-

-

-

37

FRONT WIPER ARM AND BLADE ASSEMBLY RH

-

-

-

38

SHIELD CAP

85247

-

-

39

FRONT WIPER ARM HEAD CAP

85292B

-

-

*A

for M20A-FXS

*B

for 2ZR-FXE

N*m (kgf*cm, ft.*lbf): Specified torque

-

-

Procedure

Part Name Code

40

SERVICE PLUG GRIP

G3834

-

-

-

41

ADD COOLANT (for Inverter)

-

-

-

42

INSPECT FOR COOLANT LEAK (for Inverter)

-

-

-

43

ECU CONFIGURATION

-

-

-

44

RESOLVER LEARNING

-

-

-

PROCEDURE

1. SET INVERTER WITH CONVERTER ASSEMBLY

CAUTION:

Be sure to wear insulated gloves.

NOTICE:

  • When installing the inverter with converter assembly, be careful not to damage the parts around it.
  • To prevent damage, do not hold the inverter with converter assembly by the connectors, brackets or cooling pipes.
  • To prevent damage due to static electricity, do not touch the terminals of the disconnected connectors.
  • Make sure that the inverter with converter assembly is positioned so that the stud bolts are in contact with the base of the U-shaped portions of the No. 1 inverter bracket.
  • *a: Correct
  • *b: Incorrect

2. CONNECT MOTOR CABLE

CAUTION:

Be sure to wear insulated gloves.

NOTICE:

Do not allow any foreign matter or water to enter the inverter with converter assembly.

*a

Waterproof Seal

-

-

(1) Temporarily install the motor cable to the inverter with converter assembly with the 4 bolts,

NOTICE:

  • Do not touch the waterproof seal or terminals of the motor cable.
  • Do not damage the terminals, connector housing or inverter with converter assembly during connection.
  • Be careful to avoid cutting or pinching the waterproof seal during installation.

(2) Fully tighten the 3 bolts in the order shown in the illustration.

Torque:

8 N·m {82 kgf·cm}

(3) Using a 10 mm union nut wrench, fully tighten the bolt(A).

Torque:

Specified Tightening Torque :

8 N·m {82 kgf·cm, 71 in·lbf}

HINT:

  • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

    Click here

  • When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) torque wrench (fulcrum length of 162 mm (6.38 in.)): 7.0 N*m (71 kgf*cm, 62 in.*lbf)

(4) Temporarily install the 6 bolts.

CAUTION:

Insulate the tool with insulating tape.

NOTICE:

  • To prevent the threads from being damaged, temporarily tighten the 6 bolts by hand.
  • Do not damage the terminals, connector housing or inverter with converter assembly during connection.

(5) Fully tighten the 6 bolts.

Torque:

8 N·m {82 kgf·cm}

CAUTION:

Insulate the tool with insulating tape.

NOTICE:

  • Do not damage the terminals, connector housing or inverter with converter assembly during connection.
  • Be sure to use a torque wrench to tighten the bolts.

3. INSTALL UPPER INVERTER COVER

CAUTION:

Be sure to wear insulated gloves.

*a

Interlock

*b

Waterproof Seal

(1) To prevent the inverter with converter assembly from falling, temporarily install the bolt in the location shown in the illustration.

(2) Shift the position of the inverter with converter assembly and temporarily set it on top of the stud bolts as shown in the illustration.

NOTICE:

When lifting, make sure not to apply force to the motor cable.

(3) Install the inverter cover to the inverter with converter assembly with the 2 bolts.

Torque:

8 N·m {82 kgf·cm}

NOTICE:

  • To avoid deforming portion (A) of the inverter cover, do not hold portion (A) when installing.
  • Be careful not to scratch or damage portion (B) of the inverter cover.
  • Visually confirm that the inverter cover waterproof seal is securely installed before installing the upper inverter cover.
  • Do not touch the waterproof seal of the upper inverter cover.
  • Make sure that the interlock is fully engaged.
  • Do not damage the terminals, interlock connector or inverter with converter assembly during installation.
  • Do not allow any foreign matter or water to enter the inverter with converter assembly.
  • Do not remove or excessively tighten the screw of the upper inverter cover.

    *1

    Inverter Cover

    *a

    Screw

  • Although the upper inverter cover may feel loose, this is not due to a malfunction.
  • Push in the upper inverter cover until it contacts the inverter with converter assembly.

    *a

    No Gap

(1) Shift the position of the inverter with converter assembly and temporarily set it on the hybrid Toyota Prius vehicle transaxle assembly as shown in the illustration.

NOTICE:

When lifting, make sure not to apply force to the motor cable.

(2) Install the inverter cover with the bolt to the hybrid vehicle transaxle assembly.

Torque:

8 N·m {82 kgf·cm}

4. INSTALL INVERTER WITH CONVERTER ASSEMBLY

CAUTION:

Be sure to wear insulated gloves.

(1) Temporarily install the inverter with converter assembly with the 5 bolts and 2 nuts.

NOTICE:

  • When installing the inverter with converter assembly, be careful not to damage the parts around it.
  • To prevent damage due to static electricity, do not touch the terminals of the disconnected connectors.
  • Make sure that the inverter with converter assembly is positioned so that the stud bolts are in contact with the base of the U-shaped portions of the No. 1 inverter bracket.

    *a

    Correct

    *b

    Incorrect

HINT:

If the bolts and nuts are not tightened appropriately, the inverter with converter assembly may make an abnormal noise.

(2) Fully tighten the 4 bolts in the order shown in the illustration.

Torque:

55 N·m {561 kgf·cm, 41 ft·lbf}

(3) Fully tighten the 2 nuts.

Torque:

55 N·m {561 kgf·cm, 41 ft·lbf}

5. CONNECT ENGINE WIRE

CAUTION:

Be sure to wear insulated gloves.

6. CONNECT INLET NO. 1 INVERTER COOLING HOSE

(a) for 2ZR-FXE:

*a

Alignment Mark

*b

Rib

*c

2 to 11 mm (0.0787 to 0.4331 in.)

*d

Up

*e

LH Side

-

-

(1) Connect the inlet No. 1 inverter cooling hose to the inverter with converter assembly and slide the clip to secure it.

NOTICE:

  • To prevent foreign matter from entering the inverter with converter assembly and inverter cooling system, do not remove the pieces of cloth from the pipe and disconnected hose until installation.
  • Make sure to align the alignment mark of the hose with the rib of the inverter with converter assembly.
  • Make sure that the clip is positioned as shown in the illustration.

(b) for M20A-FXS:

*a

Alignment Mark

*b

Rib

*c

2 to 11 mm (0.0787 to 0.4331 in.)

*d

Up

*e

LH Side

-

-

(1) Connect the inlet No. 1 inverter cooling hose to the inverter with converter assembly and slide the clip to secure it.

NOTICE:

  • To prevent foreign matter from entering the inverter with converter assembly and inverter cooling system, do not remove the pieces of cloth from the pipe and disconnected hose until installation.
  • Make sure to align the alignment mark of the hose with the rib of the inverter with converter assembly.
  • Make sure that the clip is positioned as shown in the illustration.

7. CONNECT OUTLET NO. 1 INVERTER COOLING HOSE

(a) for 2ZR-FXE:

*a

Alignment Mark

*b

Rib

*c

2 to 11 mm (0.0787 to 0.4331 in.)

*d

Up

*e

LH Side

-

-

(1) Connect the outlet No. 1 inverter cooling hose to the inverter with converter assembly and slide the clip to secure it.

NOTICE:

  • To prevent foreign matter from entering the inverter with converter assembly and inverter cooling system, do not remove the pieces of cloth from the pipe and disconnected hose until installation.
  • Make sure to align the alignment mark of the hose with the rib of the inverter with converter assembly.
  • Make sure that the clip is positioned as shown in the illustration.

(b) for M20A-FXS:

*a

Alignment Mark

*b

Rib

*c

2 to 11 mm (0.0787 to 0.4331 in.)

-

-

(1) Connect the outlet No. 1 inverter cooling hose to the inverter with converter assembly and slide the clip to secure it.

NOTICE:

  • To prevent foreign matter from entering the inverter with converter assembly and inverter cooling system, do not remove the pieces of cloth from the pipe and disconnected hose until installation.
  • Make sure to align the alignment mark of the hose with the rib of the inverter with converter assembly.

8. CONNECT NO. 7 ENGINE WIRE

CAUTION:

Be sure to wear insulated gloves.

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

9. CONNECT FLOOR UNDER WIRE

CAUTION:

Be sure to wear insulated gloves.

NOTICE:

  • Do not allow any foreign matter or water to enter the inverter with converter assembly.
  • Do not touch the waterproof seal or terminals of the connector.
  • Do not damage the terminals, connector housing or inverter with converter assembly when connecting the connector.

Torque:

8 N·m {82 kgf·cm, 71 in·lbf}

10. CONNECT ENGINE ROOM MAIN WIRE

CAUTION:

Be sure to wear insulated gloves.

NOTICE:

  • To prevent the threads from being damaged, temporarily tighten the nut by hand.
  • Do not touch the waterproof seal or terminals of the connectors.
  • To prevent damage due to static electricity, do not touch the terminals of the disconnected connectors.
  • Do not damage the terminals, connector housing or inverter with converter assembly when connecting the connectors.

11. CONNECT ENGINE WIRE

CAUTION:

Be sure to wear insulated gloves.

NOTICE:

  • To prevent the threads from being damaged, temporarily tighten the nut by hand.
  • Do not touch the waterproof seal or terminals of the connectors.
  • To prevent damage due to static electricity, do not touch the terminals of the disconnected connectors.
  • Do not damage the terminals, connector housing or inverter with converter assembly when connecting the connectors.

Torque:

10 N·m {102 kgf·cm, 89 in·lbf}

12. CONNECT NO. 1 VACUUM SWITCHING VALVE ASSEMBLY (for M20A-FXS)

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

13. CONNECT NO. 3 ENGINE WIRE

Torque:

8,3 N·m {85 kgf·cm, 74 in·lbf}

14. INSTALL NO. 2 RELAY BLOCK COVER

15. CONNECT HV AIR CONDITIONING WIRE

CAUTION:

Be sure to wear insulated gloves.

NOTICE:

  • Do not allow any foreign matter or water to enter the inverter with converter assembly.
  • Do not touch the waterproof seal or terminals of the connector.
  • Do not damage the terminals, connector housing or inverter with converter assembly when connecting the connector.

(a) for 2ZR-FXE

*a

Green-colored Lock

-

-

Slide

-

-

(1) Connect the connector and slide the green-colored lock as shown in the illustration to securely lock it.

(b) for M20A-FXS

*a

Green-colored Lock

-

-

Slide

-

-

(1) Connect the connector and slide the green-colored lock as shown in the illustration to securely lock it.

(2) Engage the 2 clamps.

16. INSTALL AIR CLEANER BRACKET (for M20A-FXS)

Torque:

7 N·m {71 kgf·cm, 62 in·lbf}

17. INSTALL AIR CLEANER CASE SUB-ASSEMBLY (for M20A-FXS)

Torque:

4 N·m {41 kgf·cm, 35 in·lbf}

18. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY (for M20A-FXS)

19. INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE (for M20A-FXS)

20. CONNECT NO. 2 VENTILATION HOSE (for M20A-FXS)

21. INSTALL INLET NO. 1 AIR CLEANER (for 2ZR-FXE)

Click here

22. INSTALL AIR CLEANER BRACKET (for 2ZR-FXE)

Click here

23. INSTALL INLET NO. 2 AIR CLEANER (for 2ZR-FXE)

Click here

24. INSTALL AIR CLEANER CASE SUB-ASSEMBLY (for 2ZR-FXE)

Click here

25. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY (for 2ZR-FXE)

26. INSTALL AIR CLEANER HOSE ASSEMBLY (for 2ZR-FXE)

27. INSTALL AIR CLEANER CAP SUB-ASSEMBLY (for 2ZR-FXE)

28. INSTALL RADIATOR SUPPORT OPENING COVER (for 2ZR-FXE)

29. INSTALL BATTERY CLAMP SUB-ASSEMBLY (for 2ZR-FXE)

Torque:

15,4 N·m {157 kgf·cm, 11 ft·lbf}

30. INSTALL ECM

  • for M20A-FXS:

    Click here

  • for 2ZR-FXE:

    Click here

31. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Click here

32. INSTALL COWL WATER EXTRACT SHIELD RH

33. INSTALL COWL WATER EXTRACT SHIELD LH

34. INSTALL WINDSHIELD LOWER OUTSIDE MOULDING LH

35. INSTALL WINDSHIELD LOWER OUTSIDE MOULDING RH

36. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

Click here

37. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

Click here

38. INSTALL SHIELD CAP (for M20A-FXS)

39. INSTALL FRONT WIPER ARM HEAD CAP

40. INSTALL SERVICE PLUG GRIP

Click here

41. ADD COOLANT (for Inverter)

Click here

42. INSPECT FOR COOLANT LEAK (for Inverter)

Click here

43. PERFORM ECU CONFIGURATION

Click here

44. PERFORM RESOLVER LEARNING

  • for M20A-FXS:

    Click here

  • for 2ZR-FXE:

    Click here