Lighting System

In this manual: Lighting System
How To Troubleshoot Ecu Controlled Systems — 1How To Use This Manual — 1Identification Information — 1Repair Instruction — 1Terms — 12zr-fxe Air Cleaner Filter Element — 12zr-fxe Auxiliary Battery — 12zr-fxe Coolant (for Engine Coolant) — 12zr-fxe Oil And Oil Filter — 12zr-fxe Spark Plug — 1Air Conditioning Filter — 1Battery Cooling Filter — 1Brake Fluid — 1Coolant (for Inverter) — 1Front Brake Flexible Hose — 1Front Disc Brake Pad — 1Front Lower Ball Joint — 1Front Wheel Alignment — 1Front Wiper Rubber — 1General Maintenance — 1M20a-fxs Air Cleaner Filter Element — 1M20a-fxs Auxiliary Battery — 1M20a-fxs Coolant (for Engine Coolant) — 1M20a-fxs Oil And Oil Filter — 1M20a-fxs Spark Plug — 1Pa10/pb10/pb12 Hybrid Transaxle Fluid — 1Q810 Hybrid Transaxle Fluid — 1Rear Brake Flexible Hose — 1Rear Disc Brake Pad — 1Rear Wheel Alignment — 1Steering Column — 1Tire And Wheel — 1Transmitter Battery — 1When Disconnecting Or Reconnecting Battery Terminal — 1When Replacing Or Removing/installing Parts — 1Automatic High Beam Main Switch — 1Automatic High Beam System — 1Driver Monitor Camera — 1Driver Monitor Camera System — 1Driver Monitor Ecu — 1Front Camera — 1Front Camera System — 1Front Radar Sensor System — 1Front Side Radar Sensor — 1Front Side Radar Sensor System — 1Millimeter Wave Radar Sensor — 1Utility — 1Advanced Park — 1Advanced Park Main Switch — 1Amplifier Antenna — 1Audio And Visual System — 1Front Door Speaker — 1Instrument Panel Speaker — 1Microphone — 1Noise Filter — 1Pillar Speaker — 1Radio Antenna Cord (for Back Door) — 1Radio Antenna Cord (for Instrument Panel) — 1Radio Antenna Cord (for Roof) — 1Radio Receiver — 1Rear Door Speaker — 1Roof Antenna — 1Stereo Component Amplifier — 1Stereo Jack Adapter Assembly — 1Window Glass Antenna Wire — 1Back-up Battery — 1Dcm(telematics Transceiver) — 1Manual(sos)switch — 1Safety Connect System — 1Telephone And Gps Antenna (for Front Side) — 1Telephone And Gps Antenna (for Roof Side) — 1Telephone And Gps Antenna Cords — 1Garage Door Opener System (for Digital Inner Mirror) — 1Garage Door Opener System (for Ec Inner Mirror) — 1Blind Spot Monitor Sensor — 1Blind Spot Monitor System — 1Clearance Warning Ecu — 1Intuitive Parking Assist System — 1Panoramic View Monitor Switch — 1Panoramic View Monitor System — 1Parking Assist Ecu — 1Parking Assist Light — 1Parking Assist Monitor System — 1Parking Support Brake System — 1Rear View Monitor System — 1Television Camera (for Front) — 1Television Camera (for Rear) — 1Television Camera (for Side) — 1Ultrasonic Sensor (for Front) — 1Ultrasonic Sensor (for Rear) — 1Brake Actuator — 1Brake Pedal Stroke Sensor — 1Electronically Controlled Brake System — 1Front Speed Sensor — 1Rear Speed Sensor (for Awd) — 1Steering Angle Sensor — 1Brake Booster — 1Brake Fluid — 1Brake Line — 1Brake Pedal — 1Brake System — 1Electric Parking Brake Actuator — 1Electric Parking Brake Switch — 1Electric Parking Brake System — 1Forced Release — 1Front Axle Hub — 1Front Axle Hub Bolt — 1Rear Axle Carrier (for 2wd) — 1Rear Axle Carrier (for Awd) — 1Rear Axle Hub (for 2wd) — 1Rear Axle Hub (for Awd) — 1Rear Axle Hub Bolt — 1Steering Knuckle — 1Drive Shaft System — 1Front Drive Shaft Assembly — 1Rear Drive Shaft Assembly — 1Combination Switch — 1Electronic Shift Lever System — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Oil Seal — 1Hybrid Transaxle System — 1Input Shaft Oil Seal — 1Motor Cable — 1Pa10 Hybrid Vehicle Transaxle — 1Pa10 Manual Parking Lock Release — 1Pa10 Oil Cooler — 1Pb10/pb12 Hybrid Vehicle Transaxle — 1Pb10/pb12 Manual Parking Lock Release — 1Pb10/pb12 Oil Cooler — 1Shift Control Actuator — 1Shift Lever — 1Shift Lever Knob — 1Differential Side Gear Shaft — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Side Gear Oil Seal — 1Motor Cable — 1Rear Traction Motor — 1Coolant (for Engine) — 1Cooling Fan Motor — 1Cooling Fan System — 1Radiator — 1Relay — 1Thermostat — 1Water Pump — 1Canister — 1Egr Cooler — 1Egr Valve — 1Emission Control System — 1Fuel Tank Cap — 1Pcv Valve — 1Purge Valve — 1Vacuum Sensor — 1Air Fuel Ratio Sensor — 1Camshaft Oil Control Valve — 1Camshaft Position Sensor — 1Crankshaft Position Sensor — 1Ecm — 1Engine Coolant Temperature Sensor — 1Heated Oxygen Sensor — 1Ignition Coil And Spark Plug — 1Ignition System — 1Knock Sensor — 1Mass Air Flow Meter — 1Relay — 1Sfi System — 1Throttle Body — 1Camshaft — 1Cylinder Block — 1Cylinder Head — 1Cylinder Head Gasket — 1Engine — 1Engine Assembly — 1Engine Unit — 1Front Crankshaft Oil Seal — 1Rear Crankshaft Oil Seal — 1Fuel Filter — 1Fuel Injector — 1Fuel Pressure Regulator — 1Fuel Pump — 1Fuel Sender Gauge Assembly — 1Fuel System — 1Fuel Tank — 1Air Cleaner Filter Element — 1Exhaust Manifold — 1Exhaust Pipe — 1Intake Manifold — 1Intake System — 1Lubrication System — 1Oil And Oil Filter — 1Oil Pan And Oil Level Sensor — 1Oil Pressure Switch — 1Oil Pump — 1Accelerator Pedal Sensor — 1Battery Blower (for Hev Model) — 1Battery Ecu (for Hev Model) — 1Battery Ecu (for Phev Model) — 1Battery Voltage Sensor (for Phev Model) — 1Charge Cable (for Phev Model) — 1Charge Indicator (for Phev Model) — 1Charge Inlet (for Phev Model) — 1Combination Switch — 1Coolant (for Inverter) — 1Cooler (for Phev Model) — 1Electric Vehicle Charger Assembly (for Phev Model) — 1Frame Wire (for Hev Model) — 1Frame Wire (for Phev Model) — 1Heater Relay (for Phev Model) — 1Hv Battery (for Hev Model) — 1Hv Battery (for Phev Model) — 1Hv Battery Heater (for Phev Model) — 1Hv Battery Stack (for Phev Model) — 1Hv Relay Assembly (for Hev Model) — 1Hv Relay Assembly (for Phev Model) — 1Hybrid Battery System (for 2zr-fxe) — 1Hybrid Battery System (for M20a-fxs) — 1Hybrid Battery System (for Phev Model) — 1Hybrid Vehicle Control Ecu — 1Inverter With Converter (for Hev Model) — 1Motor Generator Control System (for 2zr-fxe) — 1Plug-in Charge Control System (for Phev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Service Plug Grip (for Hev Model) — 1Sub Radiator — 1Water Pump With Motor — 1Auxiliary Battery — 1Battery Current Sensor — 1Charging System — 1Solar Charging System — 1Solar Control Unit — 1Solar Roof — 1Can Communication System (for Hev Model) — 1Lin Communication System — 1Network Gateway Ecu — 1Integration Control Supply — 1Main Body Ecu — 1Power Integration System — 1Sub Battery System — 1Power Steering Ecu — 1Power Steering System — 1Heated Steering Wheel Controller — 1Heated Steering Wheel System — 1Steering Column Assembly — 1Steering Heater Switch — 1Steering Pad Switch — 1Steering System — 1Steering Wheel — 1Front Lower Ball Joint — 1Front Lower Suspension Arm (for 2zr-fxe Lh Side) — 1Front Lower Suspension Arm (for 2zr-fxe Rh Side) — 1Front Lower Suspension Arm (for M20a-fxs) — 1Front Shock Absorber — 1Front Stabilizer Bar — 1Front Suspension Member — 1Rear Coil Spring — 1Rear Lower Arm (for Awd Lh Side) — 1Rear Lower Arm (for Awd Rh Side) — 1Rear Lower Arm (for Hev Model 2wd) — 1Rear Lower Arm (for Phev Model) — 1Rear Shock Absorber — 1Rear Stabilizer Bar — 1Rear Suspension Member (for 2wd) — 1Rear Suspension Member (for Awd) — 1Rear Trailing Arm — 1Rear Upper Arm — 1Tire And Wheel System — 1Tire Repair Seal — 1Tire Pressure Warning Receiver — 1Tire Pressure Warning System — 1Tire Pressure Warning Valve — 1Acoustic Vehicle Alerting System — 1Vehicle Approaching Speaker — 1Vehicle Approaching Speaker Ecu — 1Back Door — 1Back Door Closer Ecu — 1Back Door Opener Switch — 1Back Door Support — 1Back Door Weatherstrip — 1Charge Lid Courtesy Switch — 1Charge Lid Opener Motor Assembly — 1Charge Lid Opener System — 1Charge Lid Opener Unit — 1Front Door — 1Front Door Opening Trim Weatherstrip — 1Fuel Lid Opener Motor Assembly — 1Fuel Lid Opener Switch — 1Fuel Lid Opener System — 1Hood — 1Hood Lock Control Cable Assembly — 1Power Back Door Closer Switch — 1Power Back Door Control Switch — 1Power Back Door Drive Unit — 1Power Back Door System — 1Power Back Door Touch Sensor — 1Power Back Door Warning Buzzer — 1Rear Door — 1Rear Door Opening Trim Weatherstrip — 1Reserve Lock Switch — 1Front Bumper — 1Front Door Belt Moulding — 1Front Door Window Frame Moulding — 1Front Fender — 1Front Pillar Upper Cover — 1Grille Shutter — 1Grille Shutter System — 1Name Plate — 1Quarter Garnish — 1Rear Bumper — 1Rear Door Belt Moulding — 1Rear Door Window Frame Moulding — 1Rear Wheel House Plate — 1Rocker Panel Moulding — 1Roof Drip Side Finish Moulding — 1Roof Garnish — 1Wheel Opening Moulding (for Front Side) — 1Wheel Opening Moulding (for Rear Side) — 1Windshield Outside Moulding — 1Horn — 1Horn System — 1Relay — 1Automatic Light Control Sensor — 1Back-up Light Assembly — 1Charge Lid Light — 1Front Marker Light — 1Hazard Warning Switch — 1Headlight Assembly — 1Headlight Dimmer Switch — 1Headlight Leveling Switch — 1High Mounted Stop Light Assembly — 1Illumination Light Assembly — 1License Plate Light Assembly — 1Lighting System — 1Rear Combination Light Assembly — 1Rear Light Assembly — 1Rear Side Marker Light Assembly — 1Relay — 1Side Turn Signal Light Assembly — 1Stop Light Switch — 1Switch Housing — 1Outer Mirror Switch — 1Outer Rear View Mirror — 1Outer Rear View Mirror Cover — 1Outer Rear View Mirror Glass — 1Power Mirror Control System — 1Back Door Glass — 1Front Passenger Side Power Window Switch — 1Power Window Control System — 1Power Window Master Switch — 1Power Window Regulator Motor (for Front Door) — 1Power Window Regulator Motor (for Rear Door) — 1Rear Power Window Switch — 1Relay — 1Roof Window Fix Glass — 1Window Defogger System — 1Windshield Deicer Switch — 1Windshield Deicer System — 1Windshield Glass — 1Front Wiper Motor — 1Rain Sensor — 1Relay — 1Washer Motor — 1Washer Nozzle (for Front Side) — 1Washer Nozzle (for Rear Television Camera) — 1Wiper And Washer System — 1Wiper Ecu — 1Wiper Switch — 1Back Door Lock — 1Door Control Receiver — 1Door Control Switch — 1Door Control Transmitter — 1Door Lock Release Motor (for Rear Side) — 1Door Outside Handle (for Rear Side) — 1Front Door Lock — 1Power Door Lock Control System — 1Rear Door Lock — 1Transmitter Battery — 1Wireless Door Lock Control System — 1Accumulator — 1Air Conditioning Amplifier — 1Air Conditioning Panel — 1Air Conditioning Pressure Sensor — 1Air Conditioning Unit — 1Ambient Temperature Sensor — 1Blower Unit — 1Condenser (for Hev Model) — 1Condenser (for Phev Model) — 1Discharge Temperature Sensor — 1Electric Expansion Valve (cooling) — 1Electric Expansion Valve (heating) — 1Evaporator Pipe Temperature Sensor — 1Evaporator Pressure Regulator — 1Front Blower Motor — 1Front Evaporator Front Solenoid Valve — 1Air Conditioning System (for Hev Model) — 1Front Evaporator Temperature Sensor — 1Heat Exchanger Temperature Sensor — 1Heat Pump Ecu — 1High Pressure Magnetic Valve — 1Humidity Sensor — 1Internal Condenser Temperature Sensor — 1Low Pressure Magnetic Valve — 1Refrigerant (for Hfc-134a(r134a)) — 1Refrigerant Line (for Hev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Room Temperature Sensor — 1Solar Sensor — 1Floor Carpet — 1Front Console Box — 1Instrument Panel Safety Pad — 1Roof Headlining — 1Roof Sunshade — 1Ambient Light (for Driver Side) — 1Ambient Light (for Front Passenger Side) — 1Back Door Courtesy Switch — 1Footwell Light — 1Glove Box Light — 1Lighting System — 1Luggage Compartment Room Light — 1Personal Light — 1Room Light — 1Vanity Light — 1Vanity Light Switch — 1Combination Meter — 1Meter / Gauge System — 1Trip Switch — 1Digital Inner Mirror — 1Digital Rear-view Mirror System — 1Inner Mirror Monitor Camera — 1Inner Rear View Mirror (w/o Ec Mirror) — 1Accessory Power Outlet System — 1Power Outlet Socket (for Console Box Front Side) — 1Power Outlet Socket (for Console Box Rear Side) — 1Power Outlet Socket (for Console Box) — 1Power Outlet Socket (for Luggage Compartment) — 1Power Outlet Switch — 1Wireless Charger Assembly — 1Wireless Charging System — 1Climate Control Seat System — 1Front Power Seat Control System (w/ Memory) — 1Front Power Seat Motor Assembly — 1Front Seat Assembly (for Power Seat) — 1Front Seat Cushion Heater (for Power Seat) — 1Front Seatback Heater (for Power Seat) — 1Lumbar Support Adjuster Assembly — 1Power Seat Control Ecu — 1Power Seat Switch — 1Power Seat Track Rail Assembly — 1Rear Seat Assembly — 1Rear Seat Cushion Heater — 1Rear Seat Reminder System — 1Rear Seatback Heater — 1Seat Heater Control — 1Seat Heater Switch (for Front Seat) — 1Seat Heater Switch (for Rear Side) — 1Seat Heater System — 1Seat Memory Switch — 1Child Restraint Seat Anchor Bracket — 1Front Seat Inner Belt Assembly — 1Front Seat Outer Belt Assembly — 1Occupant Detection Sensor (for Front Passenger Side) — 1Rear Center Seat Outer Belt Assembly — 1Rear Seat Inner Belt Assembly (for Rh Side) — 1Rear Seat Outer Belt Assembly — 1Seat Belt Warning System (w/ Occupant Classification System) — 1Tongue Plate Stopper — 1Airbag System — 1Center Airbag Sensor Assembly — 1Curtain Shield Airbag Assembly — 1Front Airbag Sensor — 1Front Passenger Airbag Assembly — 1Front Seat Side Airbag Assembly — 1Inspection After Collision — 1Knee Airbag Assembly — 1Occupant Classification System — 1Rear Seat Side Airbag Assembly — 1Side Airbag Sensor (for Center Pillar) — 1Side Airbag Sensor (for Front Door) — 1Spiral Cable — 1Steering Pad — 1Certification Ecu — 1Digital Key Ecu — 1Digital Key Receiver (for Front Floor) — 1Digital Key Receiver (for Outside Luggage Compartment) — 1Digital Key Receiver (for Rear Door) — 1Digital Key System — 1Electrical Key Oscillator (for Front Floor) — 1Electrical Key Oscillator (for Outside Luggage Compartment) — 1Electrical Key Oscillator (for Rear Floor) — 1Engine Hood Courtesy Switch — 1Id Code Box — 1Smart Key System (for Start Function) — 1
~100min read
  • Precaution
  • Parts Location
  • System Diagram
  • How To Proceed With Troubleshooting
  • Operation Check
  • Customize Parameters
  • Problem Symptoms Table
  • Terminals Of Ecu
  • Diagnosis System
  • Data List / Active Test
  • IG Signal Circuit
  • Front Door Courtesy Switch Circuit
  • Back Door Courtesy Switch Circuit
  • Interior Light Circuit
  • Interior Light Auto Cut Circuit
  • Footwell Light Circuit
  • Ambient Illumination Light Circuit
  • Illumination Notification does not Operate
  • Push Start Switch Illumination Circuit
  • Instrument Panel Illumination does not Turn On
  • Door Unlock Detection Switch Circuit

Precaution

PRECAUTION

PRECAUTIONS FOR DISCONNECTING CABLE FROM NEGATIVE (-) AUXILIARY BATTERY TERMINAL

NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click here

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click here

Parts Location

PARTS LOCATION

ILLUSTRATION

*1

VANITY LIGHT ASSEMBLY (RH)

*2

MAP LIGHT ASSEMBLY

*3

VANITY LIGHT ASSEMBLY (LH)

*4

SPOT LIGHT ASSEMBLY

*5

NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY

-

-

ILLUSTRATION

*A

w/ Ambient Illumination Light

*B

w/ Footwell Light

*1

PUSH START SWITCH

*2

NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY (NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY)

*3

NO. 2 INTERIOR ILLUMINATION LIGHT ASSEMBLY (NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY)

*4

NO. 2 INTERIOR ILLUMINATION LIGHT ASSEMBLY (LH)

*5

NO. 2 INTERIOR ILLUMINATION LIGHT ASSEMBLY (RH)

-

-

ILLUSTRATION

*1

VISOR ASSEMBLY LH

*2

VISOR ASSEMBLY RH

*3

FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH

*4

FRONT DOOR LOCK WITH MOTOR ASSEMBLY RH

*5

REAR DOOR LOCK ASSEMBLY LH

*6

REAR DOOR LOCK ASSEMBLY RH

*7

BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY

-

-

ILLUSTRATION

*1

POWER DISTRIBUTION BOX ASSEMBLY

*2

MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

*3

DLC3

-

-

ILLUSTRATION

*A

w/ Wireless Charging System

*B

for 12.3 Inch Display

*C

for 8 Inch Display

-

-

*1

COMBINATION METER ASSEMBLY

*2

STEERING PAD SWITCH ASSEMBLY

*3

SPIRAL CABLE SUB-ASSEMBLY

*4

NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY

*5

AIR CONDITIONING CONTROL ASSEMBLY

*6

MOBILE WIRELESS CHARGER CRADLE ASSEMBLY

*7

RADIO AND DISPLAY RECEIVER ASSEMBLY

-

-

ILLUSTRATION

*A

w/ Rear Seat Heater

*B

w/ Advanced Park

*C

w/ Heated Steering Heater System

*D

w/ Manual Headlight Leveling System

*E

w/ Panoramic View Monitor System

*F

w/ Power Back Door System

*G

w/ Windshield Deicer System

*H

w/ Accessory Power Outlet System

*1

REAR SEAT HEATER SWITCH (LH)

*2

REAR SEAT HEATER SWITCH (RH)

*3

IPA MAIN SWITCH ASSEMBLY

*4

ELECTRIC PARKING BRAKE SWITCH ASSEMBLY

*5

STEERING HEATER SWITCH

*6

FUEL LID OPENER SWITCH

*7

HEADLIGHT LEVELING SWITCH

*8

PANORAMIC VIEW MONITOR SWITCH

*9

POWER BACK DOOR CONTROL SWITCH

*10

FRONT WINDOW DEICER SWITCH

*11

AUTO HIGH BEAM SWITCH

*12

HAZARD WARNING SIGNAL SWITCH ASSEMBLY

*13

TRIP SWITCH

*14

POWER OUTLET SWITCH

ILLUSTRATION

*1

MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

*2

DOOR CONTROL SWITCH ASSEMBLY

*3

POWER WINDOW REGULATOR SWITCH ASSEMBLY

*4

REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (LH)

*5

REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (RH)

-

-

System Diagram

SYSTEM DIAGRAM

How To Proceed With Troubleshooting

HINT:

Use the following procedure to troubleshoot the lighting system.

PROCEDURE

  1. VEHICLE BROUGHT TO WORKSHOP

NEXT
  1. CUSTOMER PROBLEM ANALYSIS AND SYMPTOM CHECK

HINT:

  • In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
  • Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
  • The following 5 items are important points for problem analysis:

    What

    Toyota Prius Vehicle model, system name

    When

    Date, time, occurrence frequency

    Where

    Road conditions

    Under what conditions?

    Driving conditions, weather conditions

    How did it happen?

    Problem symptoms

NEXT
  1. PRE-CHECK

(a) Measure the auxiliary battery voltage with the ignition switch off.

Standard Voltage:

11 to 14 V

If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.

(b) Check the fuses and relays.

(c) Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.

NEXT
  1. CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*

(a) Using the GTS, check for CAN communication system DTCs.

for HEV Model: Click here

for PHEV Model: Click here

Result

Proceed to

CAN DTCs are not output

A

CAN DTCs are output

B

B

GO TO CAN COMMUNICATION SYSTEM

for HEV Model: Click here

for PHEV Model: Click here

A
  1. PROBLEM SYMPTOMS TABLE

(a) Refer to Problem Symptoms Table.

Click here

Result

Proceed to

Fault is not listed in Problem Symptoms Table

A

Fault is listed in Problem Symptoms Table

B

B

GO TO PROBLEM SYMPTOMS TABLE

A
  1. OVERALL ANALYSIS AND TROUBLESHOOTING*

(a) Operation Check.

Click here

(b) Terminals of ECU.

Click here

(c) Data List / Active Test.

Click here

(d) Inspection.

NEXT
  1. ADJUST, REPAIR OR REPLACE

NEXT
  1. CONFIRMATION TEST

NEXT

END

Operation Check

OPERATION CHECK

INSPECT ILLUMINATED ENTRY SYSTEM OPERATION

NOTICE:

Perform this inspection with the customize settings set to their default setting.

HINT:

Perform this inspection with the door linked switch of the map light assembly on and switch of the No. 1 room light assembly in the off (DOOR) position.

Function

Outline

Lights that Operate

*1: w/ Footwell light

*2: w/ Ambient illumination light

Actuation Area-linked

When a registered key is brought within any Toyota Prius vehicle exterior detection area around the doors, the lights that operate turn on.

In the following situations, the lights listed to the right dimly illuminate when an electrical key transmitter is carried inside any of the vehicle exterior detection areas.

  • IG OFF
  • All doors are closed
  • All doors are locked
Full illumination
  • No. 2 Interior Illumination Light Assembly (LH/RH)*1
  • No. 1 Interior Illumination Light Assembly (No. 1 Instrument Panel Garnish Sub-assembly)*2
  • No. 2 Interior Illumination Light Assembly (for Front Passenger Side) (No. 2 Instrument Panel Garnish Sub-assembly)*2
  • No. 2 Interior Illumination Light Assembly (for Center) (No. 2 Instrument Panel Garnish Sub-assembly)*2
Dimmed
  • Map Light Assembly
  • Spot Light Assembly

Door Lock/Unlock-linked

(When entering the Toyota Prius vehicle)

In the above situation, the lights listed to the right illuminate when any door is unlocked.

  • Map Light Assembly
  • Spot Light Assembly
  • No. 2 Interior Illumination Light Assembly (LH/RH)*1
  • No. 1 Interior Illumination Light Assembly (No. 1 Instrument Panel Garnish Sub-assembly)*2
  • No. 2 Interior Illumination Light Assembly (for Front Passenger Side) (No. 2 Instrument Panel Garnish Sub-assembly)*2
  • No. 2 Interior Illumination Light Assembly (for Center) (No. 2 Instrument Panel Garnish Sub-assembly)*2

Door Open/Close-linked

(When entering the Toyota Prius vehicle)

In the above situation, the lights listed to the right illuminate when any door is opened.

Full illumination
  • Map Light Assembly
  • Spot Light Assembly
  • No. 2 Interior Illumination Light Assembly (LH/RH)*1
  • No. 1 Interior Illumination Light Assembly (No. 1 Instrument Panel Garnish Sub-assembly)*2
  • No. 2 Interior Illumination Light Assembly (for Front Passenger Side) (No. 2 Instrument Panel Garnish Sub-assembly)*2
  • No. 2 Interior Illumination Light Assembly (for Center) (No. 2 Instrument Panel Garnish Sub-assembly)*2
Dimmed
  • Push Start Switch Illumination

Brake-linked

In the above situation, the lights listed to the right illuminate when the brake pedal is depressed.

  • Map Light Assembly
  • Spot Light Assembly
  • No. 2 Interior Illumination Light Assembly (LH/RH)*1
  • No. 1 Interior Illumination Light Assembly (No. 1 Instrument Panel Garnish Sub-assembly)*2
  • No. 2 Interior Illumination Light Assembly (for Front Passenger Side) (No. 2 Instrument Panel Garnish Sub-assembly)*2
  • No. 2 Interior Illumination Light Assembly (for Center) (No. 2 Instrument Panel Garnish Sub-assembly)*2
  • Push Start Switch Illumination

Push Start Switch-linked

In the above situation, the lights listed to the right illuminate when the ignition switch is turned from off or ACC to ON.

Full illumination
  • Map Light Assembly

    (Down Light)

  • No. 2 Interior Illumination Light Assembly (LH/RH)*1
  • No. 1 Interior Illumination Light Assembly (No. 1 Instrument Panel Garnish Sub-assembly)*2
  • No. 2 Interior Illumination Light Assembly (for Front Passenger Side) (No. 2 Instrument Panel Garnish Sub-assembly)*2
  • No. 2 Interior Illumination Light Assembly (for Center) (No. 2 Instrument Panel Garnish Sub-assembly)*2
Dimmed
  • Push Start Switch Illumination

Shift Position-linked

In the above situation, the lights listed to the right dimly illuminate when the shift state is changed to other than P.

  • Map Light Assembly

    (Down Light)

  • No. 2 Interior Illumination Light Assembly (LH/RH)*1
  • No. 1 Interior Illumination Light Assembly (No. 1 Instrument Panel Garnish Sub-assembly)*2
  • No. 2 Interior Illumination Light Assembly (for Front Passenger Side) (No. 2 Instrument Panel Garnish Sub-assembly)*2
  • No. 2 Interior Illumination Light Assembly (for Center) (No. 2 Instrument Panel Garnish Sub-assembly)*2
  • Push Start Switch Illumination

IG ON → OFF

(When exiting the Toyota Prius vehicle)

In the above situation, the lights listed to the right illuminate when the ignition switch is turned from ON to off or ACC.

Full illumination
  • Map Light Assembly
  • Spot Light Assembly
  • No. 2 Interior Illumination Light Assembly (LH/RH)*1
  • No. 1 Interior Illumination Light Assembly (No. 1 Instrument Panel Garnish Sub-assembly)*2
  • No. 2 Interior Illumination Light Assembly (for Front Passenger Side) (No. 2 Instrument Panel Garnish Sub-assembly)*2
  • No. 2 Interior Illumination Light Assembly (for Center) (No. 2 Instrument Panel Garnish Sub-assembly)*2
Dimmed
  • Push Start Switch Illumination

Door Lock/Unlock-linked

(When exiting the Toyota Prius vehicle)

In the above situation, the lights listed to the right dimly illuminate when any door is locked for approximately 7.5 seconds, or until the electrical key transmitter is carried outside of the detection area, and then turn off.

  • Map Light Assembly
  • Spot Light Assembly
  • No. 2 Interior Illumination Light Assembly (LH/RH)*1
  • No. 1 Interior Illumination Light Assembly (No. 1 Instrument Panel Garnish Sub-assembly)*2
  • No. 2 Interior Illumination Light Assembly (for Front Passenger Side) (No. 2 Instrument Panel Garnish Sub-assembly)*2
  • No. 2 Interior Illumination Light Assembly (for Center) (No. 2 Instrument Panel Garnish Sub-assembly)*2
  • Push Start Switch Illumination

Delay

When approximately 15 seconds elapse after any of the following conditions is met, the lights that operate turn off:

  • An actuation area-linked function is operated.
  • The door unlock-linked function is operated.
  • Any door is opened and then all doors are closed when the ignition switch is off.
  • The ignition switch is turned from ON to ACC or off when all the doors are closed.
  • Map Light Assembly
  • Spot Light Assembly
  • Vanity Light Assembly (LH/RH)
  • No. 1 Luggage Compartment Light Assembly

INSPECT BATTERY SAVING CONTROL OPERATION

(a) The operations and conditions of this control are described below.

Control

Condition

Lights that Operate

Battery Saving

When 20 minutes elapse after the ignition switch is turned from ON to ACC or off and the lights that operate remain on, the lights are turned off.

HINT:

Battery saving control is canceled when any of the following operations is performed before the lights are turned off by battery saving control. After the operation is performed, the lights remain on for another 20 minutes and then the lights are turned off.

  • The ignition switch is turned to ON.
  • Any door is opened and closed.
  • Any door is unlocked.
  • The key enters any exterior actuation area.
  • Map Light Assembly
  • Spot Light Assembly
  • Vanity Light Assembly (LH/RH)
  • No. 1 Luggage Compartment Light Assembly

When 20 minutes elapse after the ignition switch is turned from ON to ACC or off and the lights that operate remain on, the lights that operate turn off.

HINT:

Battery saving control is canceled when any of the following operations is performed before the light is turned off by battery saving control. After the operation is performed, the light remains on for another 20 minutes and then the light is turned off.

  • The ignition switch is turned to ON.
  • Any door is opened and closed.
  • Any door is unlocked.
  • The key enters any exterior actuation area.

Push Start Switch Illumination

Customize Parameters

CUSTOMIZE PARAMETERS

CUSTOMIZE LIGHTING SYSTEM (INT)

NOTICE:

  • When the customer requests a change in a function, first make sure that the function can be customized.
  • Be sure to make a note of the current settings before customizing.
  • When troubleshooting a function, first make sure that the function is set to the default setting.

HINT:

The following items can be customized.

(a) Customizing using the GTS

(1) Select the setting by referring to the table below.

Illuminated Entry

Tester Display

Description

Default

Setting

ECU

Interior Lights ON when Approached Function

Lights up the following lights when the door linked switch of the map light assembly is on, switch of the No. 1 room light assembly is in the off (DOOR) position and the electrical key transmitter is brought near the Toyota Prius vehicle:

Full illumination
  • No. 2 Interior Illumination Light Assembly (LH/RH)*1
  • No. 1 Interior Illumination Light Assembly (No. 1 Instrument Panel Garnish Sub-assembly)*2
  • No. 2 Interior Illumination Light Assembly (for Front Passenger Side) (No. 2 Instrument Panel Garnish Sub-assembly)*2
  • No. 2 Interior Illumination Light Assembly (for Center) (No. 2 Instrument Panel Garnish Sub-assembly)*2
Dimmed
  • Map Light Assembly
  • Spot Light Assembly

Enable

$00:Disable,$01:Enable

Main body ECU (Multiplex network body ECU)

Interior Lights ON when Door Unlocked Function

Lights up the following lights automatically when the door linked switch of the map light assembly is on, switch of the No. 1 room light assembly is in the off (DOOR) position and the doors are unlocked by an unlock operation:

  • Map Light Assembly
  • Spot Light Assembly
  • No. 2 Interior Illumination Light Assembly (LH/RH)*1
  • No. 1 Interior Illumination Light Assembly (No. 1 Instrument Panel Garnish Sub-assembly)*2
  • No. 2 Interior Illumination Light Assembly (for Front Passenger Side) (No. 2 Instrument Panel Garnish Sub-assembly)*2
  • No. 2 Interior Illumination Light Assembly (for Center) (No. 2 Instrument Panel Garnish Sub-assembly)*2

Enable

$00:Disable,$01:Enable

Main body ECU (Multiplex network body ECU)

Interior Lights ON when IG OFF Function

Lights up the following lights automatically when the door linked switch of the map light assembly is on, switch of the No. 1 room light assembly is in the off (DOOR) position and the ignition switch is turned from ON to off:

Full illumination
  • Map Light Assembly
  • Spot Light Assembly
  • No. 2 Interior Illumination Light Assembly (LH/RH)*1
  • No. 1 Interior Illumination Light Assembly (No. 1 Instrument Panel Garnish Sub-assembly)*2
  • No. 2 Interior Illumination Light Assembly (for Front Passenger Side) (No. 2 Instrument Panel Garnish Sub-assembly)*2
  • No. 2 Interior Illumination Light Assembly (for Center) (No. 2 Instrument Panel Garnish Sub-assembly)*2
Dimmed
  • Push Start Switch Illumination

Enable

$00:Disable,$01:Enable

Main body ECU (Multiplex network body ECU)

Light Control Function

Lights up the following lights when the ignition switch is ON and the shift lever is moved to any position other than P

Full illumination
  • No. 2 Interior Illumination Light Assembly (LH/RH)*1
  • No. 1 Interior Illumination Light Assembly (No. 1 Instrument Panel Garnish Sub-assembly)*2
  • No. 2 Interior Illumination Light Assembly (for Front Passenger Side) (No. 2 Instrument Panel Garnish Sub-assembly)*2
  • No. 2 Interior Illumination Light Assembly (for Center) (No. 2 Instrument Panel Garnish Sub-assembly)*2
Dimmed
  • Push Start Switch Illumination

Enable

$00:Disable,$01:Enable

Main body ECU (Multiplex network body ECU)

Interior Illumination Light 1 Function

Turns on the following lights:

  • No. 2 Interior Illumination Light Assembly (LH/RH)*1

Enable

$00:Disable,$01:Enable

Main body ECU (Multiplex network body ECU)

Interior Illumination Light 2 Function

Turns on the following lights:

  • No. 1 Interior Illumination Light Assembly (No. 1 Instrument Panel Garnish Sub-assembly)*2
  • No. 2 Interior Illumination Light Assembly (for Front Passenger Side) (No. 2 Instrument Panel Garnish Sub-assembly)*2
  • No. 2 Interior Illumination Light Assembly (for Center) (No. 2 Instrument Panel Garnish Sub-assembly)*2

Enable

$00:Disable,$01:Enable

Main body ECU (Multiplex network body ECU)

Interior Illumination Light 3 Function

-

-

$00:Disable,$01:Enable

Cannot be used

Interior Lights Lighting Timer Setting

Changes the lighting time of the following lights that are operated by the timer function when the door linked switch of the map light assembly is on and switch of the No. 1 room light assembly is in the off (DOOR) position:

  • Map Light Assembly
  • Spot Light Assembly
  • Vanity Light Assembly (LH/RH)
  • No. 1 Luggage Compartment Light Assembly

Normal

$00:Normal,$01:Short,$02:Long

Main body ECU (Multiplex network body ECU)

Interior Lights ON Function

Lights up the following lights:

  • Map Light Assembly
  • Spot Light Assembly
  • Vanity Light Assembly (LH/RH)
  • No. 1 Luggage Compartment Light Assembly

Enable

$00:Disable,$01:Enable

Main body ECU (Multiplex network body ECU)

*1: w/ Footwell light

*2: w/ Ambient illumination light

Smart Key / Access

Tester Display

Description

Default

Setting

ECU

Start Switch Light Function

Setting for the function to turn on the push start switch illumination.

ON

$00:OFF,$01:ON

Certification ECU (Smart key ECU assembly)

Front Recognition Camera

Tester Display

Description

Default

Setting

ECU

Illumination Notification

Setting for the function to turn on the illumination notification.*

ON

$00:OFF,$01:ON

Forward recognition camera

*: w/ Ambient illumination light

(b) Customizing with the multi-display

(1) Turn the ignition switch to ON.

(2) Enter the following menus: MENU / Settings / Toyota Prius Vehicle customize / Lights.

(3) Select the setting by referring to the table below.

Display

Default

Content

Setting

Relevant ECU

Interior Lights Auto-off Timer

15 sec.

Changes the lighting time of the following lights that are operated by the timer function when the door linked switch of the map light assembly is on and switch of the No. 1 room light assembly is in the off (DOOR) position:

  • Map Light Assembly
  • Spot Light Assembly
  • Vanity Light Assembly (LH/RH)
  • No. 1 Luggage Compartment Light Assembly

Off, 7.5 sec., 15 sec., 30 sec.

Main body ECU (Multiplex network body ECU)

Problem Symptoms Table

PROBLEM SYMPTOMS TABLE

NOTICE:

Before replacing the main body ECU (multiplex network body ECU) or certification ECU (smart key ECU assembly), refer to Registration.

Click here

HINT:

  • Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
  • Inspect the fuses and relays related to this system before inspecting the suspected areas below.
Map Light

Symptom

Suspected Area

Link

Map light LH or map light RH does not illuminate (Other interior lights are normal)

Map light assembly

Harness or connector

-

Map light LH and map light RH do not illuminate (Other interior lights are normal)

Map light assembly

Harness or connector

-

Dome light does not illuminate (Other interior lights are normal)

Interior light auto cut circuit

Interior light circuit

Map light assembly

Switch illumination and down light do not illuminate (Other interior lights are normal)

Map light assembly

Harness or connector

-

Spot Light

Symptom

Suspected Area

Link

Spot light assembly does not illuminate (Other interior lights are normal)

Spot light assembly

Interior light circuit

Map light assembly

Harness or connector

-

Footwell Light

Symptom

Suspected Area

Link

Footwell light LH does not illuminate

No. 2 interior illumination light assembly (LH)

Harness or connector

-

Footwell light RH does not illuminate

No. 2 interior illumination light assembly (RH)

Harness or connector

-

Footwell light LH and footwell light RH does not illuminate

Footwell light circuit

Harness or connector

-

Power distribution box assembly

Main body ECU (multiplex network body ECU)

Vanity Light

Symptom

Suspected Area

Link

Vanity light (for LH) does not illuminate

Vanity light assembly (LH)

Visor assembly LH

Harness or connector

-

Vanity light (for RH) does not illuminate

Vanity light assembly (RH)

Visor assembly RH

Harness or connector

-

Luggage Compartment Light

Symptom

Suspected Area

Link

Luggage compartment light does not illuminate

No. 1 luggage compartment light assembly

Harness or connector

-

Back door courtesy switch circuit

Main body ECU (Multiplex network body ECU)

Ambient Illumination Light

Symptom

Suspected Area

Link

No. 1 interior illumination light assembly (No. 1 instrument panel garnish sub-assembly) does not illuminate

No. 1 interior illumination light assembly (No. 1 instrument panel garnish sub-assembly)

Main body ECU (Multiplex network body ECU)

Harness or connector

-

No. 2 interior illumination light assembly (for front passenger side) (No. 2 instrument panel garnish sub-assembly) does not illuminate

No. 2 interior illumination light assembly (for front passenger side) (No. 2 instrument panel garnish sub-assembly)

Main body ECU (Multiplex network body ECU)

Harness or connector

-

No. 2 interior illumination light assembly (for center) (No. 2 instrument panel garnish sub-assembly) does not illuminate

No. 2 interior illumination light assembly (for center) (No. 2 instrument panel garnish sub-assembly)

Harness or connector

-

No. 1 interior illumination light assembly (No. 1 instrument panel garnish sub-assembly) and No. 2 interior illumination light assembly (for center) (No. 2 instrument panel garnish sub-assembly) does not illuminate

Main body ECU (Multiplex network body ECU)

Harness or connector

-

All ambient illumination lights does not illuminate

Ambient illumination light circuit

Main body ECU (Multiplex network body ECU)

Illumination notification does not operate

Check customize settings (Illumination Notification)

Main body ECU (Multiplex network body ECU)

Interior Light Power Source Control

Symptom

Suspected Area

Link

All the interior lights that receive power via the DOME CUT relay do not illuminate

Interior light auto cut circuit

Illuminated Entry System

Symptom

Suspected Area

Link

All illuminated entry system control functions do not operate under any condition

Check customize settings (Interior Lights ON Function)

Interior light circuit

Main body ECU (Multiplex network body ECU)

Actuation area-linked control function does not operate when registered key is brought into any exterior detection area

Check customize settings (Interior Lights ON when Approached Function)

CAN communication system (for HEV Model)

CAN communication system (for PHEV Model)

Smart key system (for Entry Function)

Main body ECU (Multiplex network body ECU)

Door lock/unlock-linked control function does not operate when doors are locked/unlocked

Check customize settings (Interior Lights ON when Door Unlocked Function)

Main body ECU (Multiplex network body ECU)

Door open/close-linked control function does not operate when doors are opened/closed

Front door courtesy switch circuit

Rea door courtesy switch circuit

Back door courtesy switch circuit

Main body ECU (Multiplex network body ECU)

Push start switch-linked control function does not operate when ignition switch is operated

Check customize settings (Interior Lights ON when IG OFF Function)

IG signal circuit

Main body ECU (Multiplex network body ECU)

Push start switch illumination does not illuminate

Check customize settings (Start Switch Light Function)

CAN communication system (for HEV Model)

CAN communication system (for PHEV Model)

Push start switch illumination circuit

Certification ECU (Smart key ECU assembly)

Shift position linked control does not operate when shift lever is operated

Check customize settings (Light Control Function)

CAN communication system (for HEV Model)

CAN communication system (for PHEV Model)

Main body ECU (Multiplex network body ECU)

Battery Saving Control System

Symptom

Suspected Area

Link

Battery saving function does not operate

Check illuminated entry system

Main body ECU (Multiplex network body ECU)

Terminals Of Ecu

TERMINALS OF ECU

CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND POWER DISTRIBUTION BOX ASSEMBLY

(a) Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.

Click here

(b) Connect the power distribution box assembly connectors.

(c) Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

z1-13 (GND1) - Body ground

Ground

Always

Below 1 Ω

z1-14 (GND2) - Body ground

Ground

Always

Below 1 Ω

z1-26 (BECU) - Body ground

Auxiliary battery power supply

Always

11 to 14 V

z1-27 (IGR) - Body ground

Ignition power supply (IG signal)

Ignition switch ON

11 to 14 V

(d) Install the main body ECU (multiplex network body ECU) to power distribution box assembly.

Click here

(e) Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

R17-20 - Body ground

Luggage compartment lights power supply

DOME CUT relay off

Below 1 V

DOME CUT relay on

11 to 14 V

K21-4 - Body ground

Interior lights power supply

DOME CUT relay off

Below 1 V

DOME CUT relay on

11 to 14 V

K17-5 (ILE) - Body ground

Illuminated entry system drive output

Illuminated entry system inactive

11 to 14 V

Illuminated entry system operation

Below 1 V

K21-18 - Body ground

No. 2 interior illumination light assembly (LH) ground

Footwell light off

11 to 14 V

Footwell light on

Below 1 V

K21-19 - Body ground

No. 2 interior illumination light assembly (RH) ground

Footwell light off

11 to 14 V

Footwell light on

Below 1 V

K16-10 (LED1) - Body ground

Ambient illumination lights ground

Ambient illumination light off

11 to 14 V

K16-14 (LED2) - Body ground

Ambient illumination light on

Below 1 V

R17-9 - Body ground

Instrument panel illumination power supply

TAIL relay off

Below 1 V

K21-2 - Body ground

TAIL relay on

11 to 14 V

CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

(a) Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

K13-20 (SWIL) - K13-30 (AGND)

Push start switch illumination drive output

Push start switch illumination on

11 to 14 V

Push start switch illumination off

Below 1 V

Diagnosis System

DIAGNOSIS SYSTEM

DESCRIPTION

(a) Lighting system data can be read from the Data Link Connector 3 (DLC3) of the vehicle. When the system seems to be malfunctioning, use the GTS to check for malfunctions and perform repairs.

CHECK DLC3

(a) Check the DLC3.

Click here

INSPECT AUXILIARY BATTERY VOLTAGE

(a) Measure the auxiliary battery voltage with the ignition switch off.

Standard Voltage:

11 to 14 V

If the voltage is below 11 V, recharge or replace the auxiliary battery.

Data List / Active Test

DATA LIST / ACTIVE TEST

DATA LIST

NOTICE:

In the following table, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

(a) Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

FR Door Lock Position Switch Status

Front door RH unlock detection switch signal

LOCK or UNLOCK

LOCK: Front door RH locked

UNLOCK: Front door RH unlocked

-

FL Door Lock Position Switch Status

Front door LH unlock detection switch signal

LOCK or UNLOCK

LOCK: Front door LH locked

UNLOCK: Front door LH unlocked

-

RR Door Lock Position Switch Status

Rear door RH unlock detection switch signal

LOCK or UNLOCK

ON: Rear door RH unlocked

OFF: Rear door RH locked

-

RL Door Lock Position Switch Status

Rear door LH unlock detection switch signal

LOCK or UNLOCK

ON: Rear door LH unlocked

OFF: Rear door LH locked

-

FR Door Courtesy Switch Status

Front door courtesy light switch assembly (for RH) signal

Close or Open

Close: Front door RH closed

Open: Front door RH open

-

FL Door Courtesy Switch Status

Front door courtesy light switch assembly (for LH) signal

Close or Open

Close: Front door LH closed

Open: Front door LH open

-

RR Door Courtesy Switch Status

Rear door courtesy light switch assembly (for RH) signal

Close or Open

Close: Rear door RH closed

Open: Rear door RH open

-

RL Door Courtesy Switch Status

Rear door courtesy light switch assembly (for LH) signal

Close or Open

Close: Rear door LH closed

Open: Rear door LH open

-

Back Door Courtesy Switch Status

Back door courtesy switch signal

Close or Open

Close: Back door closed

Open: Back door open

-

IGR Power

Ignition switch ON signal

OFF or ON

OFF: Ignition switch off

ON: Ignition switch ON

-

Communication Illumination Module "A"

-

-

-

Cannot be used

Communication Illumination Module "B"

-

-

-

Cannot be used

Communication of Color Illumination Module "A"

-

-

-

Cannot be used

Communication of Color Illumination Module "B"

-

-

-

Cannot be used

Communication of Color Illumination Module "C"

-

-

-

Cannot be used

Interior Lights ON when Approached Function

Function that lights up the interior lights when the electrical key transmitter is brought near the Toyota Prius vehicle

Disable or Enable

Enable

-

Interior Lights ON when Door Unlocked Function

Function that lights up the interior lights when the doors are unlocked by an unlock operation

Disable or Enable

Enable

-

Interior Lights ON when IG OFF Function

Function that lights up the interior lights when the ignition switch is turned from ON to off

Disable or Enable

Enable

-

Light Control Function

Function that dims the interior lights when the ignition switch is ON and the shift lever is moved to any position other than P

Disable or Enable

Enable

-

Interior Illumination Light 1 Function

Function that lights up the interior light 1 when the map light assembly is illuminated

Disable or Enable

Enable

-

Interior Illumination Light 2 Function

Function that lights up the interior light 2 when the map light assembly is illuminated

Disable or Enable

Enable

-

Interior Illumination Light 3 Function

Function that lights up the interior light 3 when the map light assembly is illuminated

Disable or Enable

Enable

-

Interior Lights Lighting Timer Setting

Changes the lighting time of the interior lights that are operated by the timer function

Normal/Short/Long

Normal

for User 1

Interior Lights ON Function

Function that lights up the interior lights

Disable or Enable

Enable

for User 1

Interior Lights Lighting Timer Setting

Changes the lighting time of the interior lights that are operated by the timer function

Normal/Short/Long

Normal

for User 2

Interior Lights ON Function

Function that lights up the interior lights

Disable or Enable

Enable

for User 2

Interior Lights Lighting Timer Setting

Changes the lighting time of the interior lights that are operated by the timer function

Normal/Short/Long

Normal

for User 3

Interior Lights ON Function

Function that lights up the interior lights

Disable or Enable

Enable

for User 3

Interior Lights Lighting Timer Setting

Changes the lighting time of the interior lights that are operated by the timer function

Normal/Short/Long

Normal

for Guest

Interior Lights ON Function

Function that lights up the interior lights

Disable or Enable

Enable

for Guest

Body Electrical > Power Distribution Box > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Panel Light Input Signal

Panel light input condition

OFF or ON

OFF: Light control switch not in tail position

ON: Light control switch in tail position

-

Panel Light Output Signal

Panel light output condition

OFF or ON

OFF: Panel light off

ON: Panel light on

-

Panel Light Output Current

Panel light current

Min.: 0, Max.: 255 A

Below 3.2 A

Interior light current when output is on

Panel Light Fuse Shut Off Status

Panel light fuse condition

OFF or ON

OFF: Fuse not shut off

ON: Fuse shut off

-

Panel Light Fuse Shut Off Count

Panel light fuse shut off history

Min.: 0, Max.: 255

Number of fuse shut off displayed

-

Body Electrical > Smart Key > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Start Switch Light Function

Setting for the function to turn on the push start switch illumination.

OFF or ON

Customized value is displayed

-

Chassis > Front Recognition Camera > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Illumination Notification

Setting for the function to turn on the Illumination notification.*

OFF or ON

Customized value is displayed

-

*: w/ Ambient illumination light

ACTIVE TEST

HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Illuminated Entry System

Turns on the lights that are controlled by the illuminated entry system*1

OFF or ON

Perform the Active Test with the door linked switch of the map light assembly on and switch of the No. 1 room light assembly in the off (DOOR) position.

Front Footwell Lights

Turns on the following lights:

  • No. 2 interior illumination light assembly (LH/RH)*2

OFF or ON

Perform the Active Test with the Toyota Prius vehicle stopped, ignition switch OFF and lock all doors.

Extended Illumination 1

Turns on the following lights:

  • No. 2 Interior Illumination Light Assembly (for Front Passenger Side) (No. 2 Instrument Panel Garnish Sub-assembly)*3

OFF or ON

Perform the Active Test with the Toyota Prius vehicle stopped and ignition switch ON.

Extended Illumination 2

Turns on the following lights:

  • No. 1 Interior Illumination Light Assembly (No. 1 Instrument Panel Garnish Sub-assembly)*3
  • No. 2 Interior Illumination Light Assembly (for Center) (No. 2 Instrument Panel Garnish Sub-assembly)*3

OFF or ON

Perform the Active Test with the Toyota Prius vehicle stopped and ignition switch ON.

Relay for Interior Light Auto Cut Function

DOME CUT relay

OFF or ON

  • OFF: DOME CUT relay on (interior lights turn on)
  • ON: DOME CUT relay off (interior lights turn off)

*1: Refer to Operation Check for the lights that are controlled by the illuminated entry system.

Click here

*2: w/ Footwell light

*3: w/ Ambient illumination light

Body Electrical > Smart Key > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Start SW Light Power Supply

Push start switch illumination

OFF or ON

-

IG Signal Circuit

DESCRIPTION

This circuit detects the ignition switch ON or off condition, and sends it to the main body ECU (multiplex network body ECU).

WIRING DIAGRAM

NOTICE:

  • Inspect the fuses for circuits related to this system before performing the following procedure.
  • Before replacing the main body ECU (multiplex network body ECU), refer to Registration.

    Click here

PROCEDURE

  1. READ VALUE USING GTS

(a) Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

IGR Power

Ignition switch ON signal

OFF or ON

OFF: Ignition switch off

ON: Ignition switch ON

-

OK:

Normal conditions listed above are displayed.

OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG
  1. CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - POWER SOURCE AND BODY GROUND)

(a) Disconnect the A13, K20 and K21 power distribution box assembly connectors.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Click Location & Routing(A13,K20) Click Connector(A13) Click Connector(K20)

Tester Connection

Condition

Specified Condition

A13-1 - Body ground

Ignition switch off

11 to 14 V

K20-10 - Body ground

Ignition switch off

Below 1 V

K20-10 - Body ground

Ignition switch ON

11 to 14 V

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(K21,K20) Click Connector(K21) Click Connector(K20)

Tester Connection

Condition

Specified Condition

K21-41 - Body ground

Always

Below 1 Ω

K20-36 - Body ground

Always

Below 1 Ω

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. INSPECT POWER DISTRIBUTION BOX ASSEMBLY

(a) Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.

Click here

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(K21,z1,K20,A13) Click Connector(K21) Click Connector(z1) Click Connector(K20) Click Connector(A13)

Tester Connection

Condition

Specified Condition

K21-41 - z1-13 (GND1)

Always

Below 1 Ω

K20-36 - z1-14 (GND2)

Always

Below 1 Ω

A13-1 - z1-27 (IGR)

Auxiliary battery not connected to K20-10 - K20-36 or K21-41

10 kΩ or higher

A13-1 - z1-27 (IGR)

Auxiliary battery positive ( ) → K20-10

Auxiliary battery negative (-) → K20-36 or K21-41

Below 1 Ω

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

Front Door Courtesy Switch Circuit

DESCRIPTION

The main body ECU (multiplex network body ECU) detects the condition of the front door courtesy light switch assembly.

WIRING DIAGRAM

NOTICE:

Before replacing the main body ECU (multiplex network body ECU), refer to Registration.

Click here

PROCEDURE

  1. READ VALUE USING GTS

(a) Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

FR Door Courtesy Switch Status

Front door courtesy light switch assembly (for RH) signal

Close or Open

Close: Front door RH closed

Open: Front door RH open

-

FL Door Courtesy Switch Status

Front door courtesy light switch assembly (for LH) signal

Close or Open

Close: Front door LH closed

Open: Front door LH open

-

Body Electrical > Main Body > Data List

Tester Display

FR Door Courtesy Switch Status

FL Door Courtesy Switch Status

OK:

Normal conditions listed above are displayed.

Result

Proceed to

OK

A

NG ("FL Door Courtesy Switch Status" is not normal)

B

NG ("FR Door Courtesy Switch Status" is not normal)

C

A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

C

GO TO STEP 5

B
  1. INSPECT FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH

Click here

NG

REPLACE FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH

OK
  1. CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH - POWER DISTRIBUTION BOX ASSEMBLY)

(a) Disconnect the R17 power distribution box assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(O2,R17) Click Connector(O2) Click Connector(R17)

Tester Connection

Condition

Specified Condition

O2-5 (CTYL) - R17-3

Always

Below 1 Ω

O2-5 (CTYL) or R17-3 - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. INSPECT POWER DISTRIBUTION BOX ASSEMBLY

(a) Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.

Click here

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(R17,z1) Click Connector(R17) Click Connector(z1)

Tester Connection

Condition

Specified Condition

R17-3 - z1-2 (FLCY)

Always

Below 1 Ω

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

  1. INSPECT FRONT DOOR LOCK WITH MOTOR ASSEMBLY RH

Click here

NG

REPLACE FRONT DOOR LOCK WITH MOTOR ASSEMBLY RH

OK
  1. CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK WITH MOTOR ASSEMBLY RH - POWER DISTRIBUTION BOX ASSEMBLY)

(a) Disconnect the R17 power distribution box assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(N2,R17) Click Connector(N2) Click Connector(R17)

Tester Connection

Condition

Specified Condition

N2-10 (CTYR) - R17-5

Always

Below 1 Ω

N2-10 (CTYR) or R17-5 - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. INSPECT POWER DISTRIBUTION BOX ASSEMBLY

(a) Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.

Click here

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(R17,z1) Click Connector(R17) Click Connector(z1)

Tester Connection

Condition

Specified Condition

R17-5 - z1-4 (FRCY)

Always

Below 1 Ω

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

Back Door Courtesy Switch Circuit

DESCRIPTION

The main body ECU (multiplex network body ECU) receives a back door open/closed signal from the multiplex network door ECU.

WIRING DIAGRAM

NOTICE:

Before replacing the main body ECU (multiplex network body ECU), refer to Registration.

Click here

PROCEDURE

  1. READ VALUE USING GTS

(a) Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Back Door Courtesy Switch Status

Back door courtesy switch signal

Close or Open

Close: Back door closed

Open: Back door open

-

Body Electrical > Main Body > Data List

Back Door Courtesy Switch Status

OK:

Normal conditions listed above are displayed.

OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG
  1. INSPECT BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY

Click here

NG

REPLACE BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY

OK
  1. CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY - POWER DISTRIBUTION BOX ASSEMBLY)

(a) Disconnect the R17 power distribution box assembly connector.

(b) Disconnect the W20 back door lock with courtesy light switch assembly.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(W20,R17) Click Connector(W20) Click Connector(R17)

Tester Connection

Condition

Specified Condition

W20-3 (D ) - R17-2

Always

Below 1 Ω

W20-3 (D ) or R17-2 - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. INSPECT POWER DISTRIBUTION BOX ASSEMBLY

(a) Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.

Click here

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(R17,z1) Click Connector(R17) Click Connector(z1)

Tester Connection

Condition

Specified Condition

R17-2 - z1-19 (BCTY)

Always

Below 1 Ω

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

Interior Light Circuit

DESCRIPTION

The main body ECU (multiplex network body ECU) controls the operation of the following lights:

  • Map Light Assembly
  • Spot Light Assembly

WIRING DIAGRAM

NOTICE:

  • Inspect the fuses for circuits related to this system before performing the following procedure.
  • Before replacing the main body ECU (multiplex network body ECU), refer to Registration.

    Click here

HINT:

The DOME CUT relay supplies power to the interior lights. If all the lights that use power from the DOME CUT relay do not turn on, check the interior light auto cut circuit first.

Click here

PROCEDURE

  1. PERFORM ACTIVE TEST USING GTS

(a) Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Illuminated Entry System

Turns on the lights that are controlled by the illuminated entry system*

OFF or ON

Perform the Active Test with the door linked switch of the map light assembly on and switch of the No. 1 room light assembly in the off (DOOR) position.

  • *: Refer to Operation Check for the lights that are controlled by the illuminated entry system.

    Click here

Body Electrical > Main Body > Active Test

Illuminated Entry System

OK:

All lights that are controlled by the illuminated entry system come on.

Result

Proceed to

OK

A

NG (Map light assembly does not come on)

B

NG (Spot light assembly does not come on)

C

NG (All lights that are controlled by the illuminated entry system do not come on)

D

A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

C

GO TO STEP 5

D

GO TO STEP 9

B
  1. INSPECT MAP LIGHT ASSEMBLY

Click here

NG

REPLACE MAP LIGHT ASSEMBLY

OK
  1. CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - MAP LIGHT ASSEMBLY)

(a) Disconnect the K21 power distribution box assembly connector.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Click Location & Routing(K21,U1) Click Connector(K21) Click Connector(U1)

Tester Connection

Condition

Specified Condition

K21-4 - U1-4 ( B1)

DOME CUT relay off

Below 1 V

DOME CUT relay on

11 to 14 V

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - BODY GROUND)

(a) Disconnect the U1 map light assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(U1) Click Connector(U1)

Tester Connection

Condition

Specified Condition

U1-6 (GND9) - Body ground

Always

Below 1 Ω

OK

USE SIMULATION METHOD TO CHECK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. INSPECT SPOT LIGHT ASSEMBLY

Click here

NG

REPLACE SPOT LIGHT ASSEMBLY

OK
  1. CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - SPOT LIGHT ASSEMBLY)

(a) Disconnect the K21 power distribution box assembly connector.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Click Location & Routing(K21,U2) Click Connector(K21) Click Connector(U2)

Tester Connection

Condition

Specified Condition

K21-4 - U2-5 (B)

Ignition switch off

11 to 14 V

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - SPOT LIGHT ASSEMBLY)

(a) Disconnect the U1 map light assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(U1,U2) Click Connector(U1) Click Connector(U2)

Tester Connection

Condition

Specified Condition

U1-8 (RRMP) - U2-2 (CTY)

Always

Below 1 Ω

U1-8 (RRMP) or U2-2 (CTY) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. INSPECT MAP LIGHT ASSEMBLY

Click here

OK

USE SIMULATION METHOD TO CHECK

NG

REPLACE MAP LIGHT ASSEMBLY

  1. CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

(a) Disconnect the U1 map light assembly connector.

(b) Disconnect the z1 main body ECU (multiplex network body ECU) connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(U1,z1) Click Connector(U1) Click Connector(z1)

Tester Connection

Condition

Specified Condition

U1-7 (DOOR) - z1-5 (ILE)

Always

Below 1 Ω

U1-7 (DOOR) or z1-5 (ILE) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - BODY GROUND)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(U1) Click Connector(U1)

Tester Connection

Condition

Specified Condition

U1-6 (GND9) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - MAP LIGHT ASSEMBLY)

(a) Disconnect the K21 power distribution box assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(K21,U1) Click Connector(K21) Click Connector(U1)

Tester Connection

Condition

Specified Condition

K21-4 - U1-4 ( B1)

Always

Below 1 Ω

K21-4 or U1-4 ( B1) - Body ground

Always

10 kΩ or higher

OK

USE SIMULATION METHOD TO CHECK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

Interior Light Auto Cut Circuit

DESCRIPTION

When the battery saving control operates, the main body ECU (multiplex network body ECU) controls the operation of the DOME CUT relay that is built into the instrument panel junction block assembly to turn off the interior lights.

WIRING DIAGRAM

NOTICE:

  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  • Before replacing the main body ECU (multiplex network body ECU), refer to Registration.

    Click here

PROCEDURE

  1. PERFORM ACTIVE TEST USING GTS

(a) Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Relay for Interior Light Auto Cut Function

DOME CUT relay

ON or OFF

  • ON: DOME CUT relay off (interior lights turn off)
  • OFF: DOME CUT relay on (interior lights turn on)
Body Electrical > Main Body > Active Test

Relay for Interior Light Auto Cut Function

OK:

All of the interior lights turn off when ON is selected.

OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG
  1. CHECK HARNESS AND CONNECTOR (POWER SOURCE - POWER DISTRIBUTION BOX ASSEMBLY)

(a) Disconnect the A14 power distribution box assembly connector.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Click Location & Routing(A14) Click Connector(A14)

Tester Connection

Condition

Specified Condition

A14-1 - Body ground

Ignition switch off

11 to 14 V

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. INSPECT POWER DISTRIBUTION BOX ASSEMBLY

(a) Connect the A14 power distribution box assembly connector.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Click Location & Routing(K21,R17) Click Connector(K21) Click Connector(R17)

Tester Connection

Condition

Specified Condition

K21-4 - Body ground

DOME CUT relay on

11 to 14 V

DOME CUT relay off

Below 1 V

R17-20 - Body ground

DOME CUT relay on

11 to 14 V

DOME CUT relay off

Below 1 V

OK

USE SIMULATION METHOD TO CHECK

NG

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

Footwell Light Circuit

DESCRIPTION

The main body ECU (multiplex network body ECU) controls the operation of the following lights:

  • No. 2 Interior Illumination Light Assembly (LH)
  • No. 2 Interior Illumination Light Assembly (RH)

WIRING DIAGRAM

NOTICE:

  • Inspect the fuses for circuits related to this system before performing the following procedure.
  • Before replacing the main body ECU (multiplex network body ECU), refer to Registration.

    Click here

PROCEDURE

  1. PERFORM ACTIVE TEST USING GTS

(a) Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Front Footwell Lights

No. 2 interior illumination light assembly (LH/RH)

OFF or ON

Perform the Active Test with the Toyota Prius vehicle stopped, ignition switch OFF and lock all doors.

Body Electrical > Main Body > Active Test

Front Footwell Lights

OK:

Footwell lights come on.

Result

Proceed to

OK

A

NG (Footwell light LH does not come on)

B

NG (Footwell light RH does not come on)

C

NG (Footwell light LH and RH do not come on)

D

A

USE SIMULATION METHOD TO CHECK

C

GO TO STEP 5

D

GO TO STEP 8

B
  1. INSPECT NO. 2 INTERIOR ILLUMINATION LIGHT ASSEMBLY (LH)

Click here

NG

REPLACE NO. 2 INTERIOR ILLUMINATION LIGHT ASSEMBLY (LH)

OK
  1. CHECK HARNESS AND CONNECTOR (NO. 2 INTERIOR ILLUMINATION LIGHT ASSEMBLY (LH) - POWER DISTRIBUTION BOX ASSEMBLY)

(a) Disconnect the K21 power distribution box assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(K28,K21) Click Connector(K28) Click Connector(K21)

Tester Connection

Condition

Specified Condition

K28-1(L) - K21-18

Always

Below 1 Ω

K28-1(L) or K21-18 - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (NO. 2 INTERIOR ILLUMINATION LIGHT ASSEMBLY (LH) - POWER DISTRIBUTION BOX ASSEMBLY)

(a) Disconnect the K20 power distribution box assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(K28,K20) Click Connector(K28) Click Connector(K20)

Tester Connection

Condition

Specified Condition

K28-2 (B) - K20-44

Always

Below 1 Ω

K28-2 (B) or K20-44 - Body ground

Always

10 kΩ or higher

OK

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. INSPECT NO. 2 INTERIOR ILLUMINATION LIGHT ASSEMBLY (RH)

Click here

NG

REPLACE NO. 2 INTERIOR ILLUMINATION LIGHT ASSEMBLY (RH)

OK
  1. CHECK HARNESS AND CONNECTOR (NO. 2 INTERIOR ILLUMINATION LIGHT ASSEMBLY (RH) - POWER DISTRIBUTION BOX ASSEMBLY)

(a) Disconnect the K21 power distribution box assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(K27,K21) Click Connector(K27) Click Connector(K21)

Tester Connection

Condition

Specified Condition

K27-1 (L) - K21-19

Always

Below 1 Ω

K27-1 (L) - K21-19 - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (NO. 2 INTERIOR ILLUMINATION LIGHT ASSEMBLY (RH) - POWER DISTRIBUTION BOX ASSEMBLY)

(a) Disconnect the K20 power distribution box assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(K27,K20) Click Connector(K27) Click Connector(K20)

Tester Connection

Condition

Specified Condition

K27-2 (B) - K20-44

Always

Below 1 Ω

K27-2 (B) or K20-44 - Body ground

Always

10 kΩ or higher

OK

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. INSPECT POWER DISTRIBUTION BOX ASSEMBLY

(a) Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.

Click here

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(K21,z1,A15,K20) Click Connector(K21) Click Connector(z1) Click Connector(A15) Click Connector(K20)

Tester Connection

Condition

Specified Condition

K21-18 - z1-16 (FSPT)

Always

Below 1 Ω

K21-19 - z1-16 (FSPT)

Always

Below 1 Ω

A15-1 - K20-44

Always

Below 1 Ω

NG

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

OK
  1. CHECK HARNESS AND CONNECTOR (NO. 2 INTERIOR ILLUMINATION LIGHT ASSEMBLY - POWER DISTRIBUTION BOX ASSEMBLY)

(a) Disconnect the K20 power distribution box assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(K28,K20,K27) Click Connector(K28) Click Connector(K20) Click Connector(K27)

Tester Connection

Condition

Specified Condition

K28-2 (B) - K20-44

Always

Below 1 Ω

K27-2 (B) - K20-44

Always

Below 1 Ω

K28-2 (B) or K20-44 - Body ground

Always

10 kΩ or higher

K27-2 (B) or K20-44 - Body ground

Always

10 kΩ or higher

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

Ambient Illumination Light Circuit

DESCRIPTION

The main body ECU (multiplex network body ECU) controls the operation of the following lights:

  • No. 1 Interior Illumination Light Assembly (No. 1 Instrument Panel Garnish Sub-assembly)
  • No. 2 Interior Illumination Light Assembly (for Front Passenger Side) (No. 2 Instrument Panel Garnish Sub-assembly)
  • No. 2 Interior Illumination Light Assembly (for Center) (No. 2 Instrument Panel Garnish Sub-assembly)

WIRING DIAGRAM

NOTICE:

  • Inspect the fuses for circuits related to this system before performing the following procedure.
  • Before replacing the main body ECU (multiplex network body ECU), refer to Registration.

    Click here

PROCEDURE

  1. PERFORM ACTIVE TEST USING GTS

(a) Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Extended Illumination 1

Turns on the following lights:

  • No. 2 Interior Illumination Light Assembly (for Front Passenger Side) (No. 2 Instrument Panel Garnish Sub-assembly)

OFF or ON

Perform the Active Test with the Toyota Prius vehicle stopped and ignition switch ON.

Extended Illumination 2

Turns on the following lights:

  • No. 1 Interior Illumination Light Assembly (No. 1 Instrument Panel Garnish Sub-assembly)
  • No. 2 Interior Illumination Light Assembly (for Center) (No. 2 Instrument Panel Garnish Sub-assembly)

OFF or ON

Perform the Active Test with the Toyota Prius vehicle stopped and ignition switch ON.

Body Electrical > Main Body > Active Test

Extended Illumination 1

Body Electrical > Main Body > Active Test

Extended Illumination 2

Result

Proceed to

OK

A

NG (No. 2 interior illumination light assembly (for front passenger side) (No. 2 instrument panel garnish sub-assembly) does not come on)

B

NG (No. 1 interior illumination light assembly (No. 1 instrument panel garnish sub-assembly) does not come on)

C

NG (No. 2 interior illumination light assembly (for center) (No. 2 instrument panel garnish sub-assembly) does not come on)

D

NG (No. 1 interior illumination light assembly (No. 1 instrument panel garnish sub-assembly) and No. 2 interior illumination light assembly (for center) (No. 2 instrument panel garnish sub-assembly) do not come on)

E

NG (All lights do not come on)

F

A

USE SIMULATION METHOD TO CHECK

C

GO TO STEP 5

D

GO TO STEP 8

E

GO TO STEP 11

F

GO TO STEP 13

B
  1. INSPECT NO. 2 INTERIOR ILLUMINATION LIGHT ASSEMBLY (for FRONT PASSENGER SIDE) (NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY)

Click here

NG

REPLACE NO. 2 INTERIOR ILLUMINATION LIGHT ASSEMBLY (for FRONT PASSENGER SIDE) (NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY)

OK
  1. CHECK HARNESS AND CONNECTOR (NO. 2 INTERIOR ILLUMINATION LIGHT ASSEMBLY (for FRONT PASSENGER SIDE) - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

(a) Disconnect the K16 main body ECU (multiplex network body ECU) connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(K16,K51) Click Connector(K16) Click Connector(K51)

Tester Connection

Condition

Specified Condition

K16-10 (LED1) - K51-1 (E)

Always

Below 1 Ω

K16-10 (LED1) or K51-1 (E) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (NO. 2 INTERIOR ILLUMINATION LIGHT ASSEMBLY (for FRONT PASSENGER SIDE) - POWER DISTRIBUTION BOX ASSEMBLY)

(a) Disconnect the K20 power distribution box assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(K51,K20) Click Connector(K51) Click Connector(K20)

Tester Connection

Condition

Specified Condition

K51-5 (B) - K20-44

Always

Below 1 Ω

K51-5 (B) or K20-44 - Body ground

Always

10 kΩ or higher

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. INSPECT NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY (NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY)

Click here

NG

REPLACE NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY (NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY)

OK
  1. CHECK HARNESS AND CONNECTOR (NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

(a) Disconnect the K16 main body ECU (multiplex network body ECU) connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(K16,K52) Click Connector(K16) Click Connector(K52)

Tester Connection

Condition

Specified Condition

K16-14 (LED2) - K52-1 (E)

Always

Below 1 Ω

K16-14 (LED2) or K52-1 (E) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY - POWER DISTRIBUTION BOX ASSEMBLY)

(a) Disconnect the K20 power distribution box assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(K52,K20) Click Connector(K52) Click Connector(K20)

Tester Connection

Condition

Specified Condition

K52-5 (B) - K20-44

Always

Below 1 Ω

K52-5 (B) or K20-44 - Body ground

Always

10 kΩ or higher

OK

USE SIMULATION METHOD TO CHECK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. INSPECT NO. 2 INTERIOR ILLUMINATION LIGHT ASSEMBLY (for CENTER) (NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY)

Click here

NG

REPLACE NO. 2 INTERIOR ILLUMINATION LIGHT ASSEMBLY (for CENTER) (NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY)

OK
  1. CHECK HARNESS AND CONNECTOR (NO. 2 INTERIOR ILLUMINATION LIGHT ASSEMBLY (for CENTER) - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

(a) Disconnect the K16 main body ECU (multiplex network body ECU) connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(K16,K95) Click Connector(K16) Click Connector(K95)

Tester Connection

Condition

Specified Condition

K16-14 (LED2) - K95-1 (E)

Always

Below 1 Ω

K16-14 (LED2) or K95-1 (E) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (NO. 2 INTERIOR ILLUMINATION LIGHT ASSEMBLY (for CENTER) - POWER DISTRIBUTION BOX ASSEMBLY)

(a) Disconnect the K20 power distribution box assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(K95,K20) Click Connector(K95) Click Connector(K20)

Tester Connection

Condition

Specified Condition

K95-5 (B) - K20-44

Always

Below 1 Ω

K95-5 (B) or K20-44 - Body ground

Always

10 kΩ or higher

OK

USE SIMULATION METHOD TO CHECK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. CHECK HARNESS AND CONNECTOR (NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

(a) Disconnect the K16 main body ECU (multiplex network body ECU) connector.

(b) Disconnect the K52 No. 1 interior illumination light assembly (No. 1 instrument panel garnish sub-assembly) connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(K16,K52) Click Connector(K16) Click Connector(K52)

Tester Connection

Condition

Specified Condition

K16-14 (LED2) - K52-1 (E)

Always

Below 1 Ω

K16-14 (LED2) or K52-1 (E) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY - POWER DISTRIBUTION BOX ASSEMBLY)

(a) Disconnect the K20 power distribution box assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(K52,K20) Click Connector(K52) Click Connector(K20)

Tester Connection

Condition

Specified Condition

K52-5 (B) - K20-44

Always

Below 1 Ω

K52-5 (B) or K20-44 - Body ground

Always

10 kΩ or higher

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - POWER SOURCE)

(a) Disconnect the A15 power distribution box assembly connectors.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Click Location & Routing(A15) Click Connector(A15)

Tester Connection

Condition

Specified Condition

A15-1 - Body ground

Ignition switch off

11 to 14 V

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. INSPECT POWER DISTRIBUTION BOX ASSEMBLY

(a) Disconnect the K20 power distribution box assembly connectors.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(A15,K20) Click Connector(A15) Click Connector(K20)

Tester Connection

Condition

Specified Condition

A15-1 - K20-44

Always

Below 1 Ω

NG

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

OK
  1. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - ILLUMINATION LIGHTS)

(a) Disconnect the K16 main body ECU (multiplex network body ECU) connector.

(b) Disconnect the K51 No. 2 interior illumination light assembly (for front passenger side) (No. 2 instrument panel garnish sub-assembly) connector.

(c) Disconnect the K52 No. 1 interior illumination light assembly (No. 1 instrument panel garnish sub-assembly) connector.

(d) Disconnect the K95 No. 2 interior illumination light assembly (for center) (No. 2 instrument panel garnish sub-assembly) connector.

(e) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(K16,K51,K52,K95) Click Connector(K16) Click Connector(K51) Click Connector(K52) Click Connector(K95)

Tester Connection

Condition

Specified Condition

K16-10 (LED1) - K51-1 (E)

Always

Below 1 Ω

K16-14 (LED2) - K52-1 (E)

Always

Below 1 Ω

K16-14 (LED2) - K95-1 (E)

Always

Below 1 Ω

K16-10 (LED1) or K51-1 (E) - Body ground

Always

10 kΩ or higher

K16-14 (LED2) or K52-1 (E) - Body ground

Always

10 kΩ or higher

K16-14 (LED2) or K95-1 (E) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (ILLUMINATION LIGHTS - POWER DISTRIBUTION BOX ASSEMBLY)

(a) Disconnect the K20 power distribution box assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(K51,K20,K52,K95) Click Connector(K51) Click Connector(K20) Click Connector(K52) Click Connector(K95)

Tester Connection

Condition

Specified Condition

K51-5 (B) - K20-44

Always

Below 1 Ω

K52-5 (B) - K20-44

Always

Below 1 Ω

K95-5 (B) - K20-44

Always

Below 1 Ω

K51-5 (B) or K20-44 - Body ground

Always

10 kΩ or higher

K52-5 (B) or K20-44 - Body ground

Always

10 kΩ or higher

K95-5 (B) or K20-44 - Body ground

Always

10 kΩ or higher

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

Illumination Notification does not Operate

DESCRIPTION

The following lights flash as an illumination notification:

  • No. 1 Interior Illumination Light Assembly (No. 1 Instrument Panel Garnish Sub-assembly)
  • No. 2 Interior Illumination Light Assembly (for Front Passenger Side) (No. 2 Instrument Panel Garnish Sub-assembly)
  • No. 2 Interior Illumination Light Assembly (for Center) (No. 2 Instrument Panel Garnish Sub-assembly)

WIRING DIAGRAM

NOTICE:

  • Inspect the fuses for circuits related to this system before performing the following procedure.
  • Before replacing the main body ECU (multiplex network body ECU), refer to Registration.

    Click here

  • By performing customization using the GTS, check that "Illumination Notification" is "ON".

    Click here

  • Using meter / gauge system customization, check that "PDA" is "ON".

    Click here

PROCEDURE

  1. CHECK FOR DTCs (HEALTH CHECK)

(a) Using the GTS, perform a health check.

OK:

DTCs are not output by any system other than the front camera system (Front Recognition Camera).

Result

Proceed to

DTC is not output

A

DTC is output

B

B

GO TO FRONT CAMERA SYSTEM

A
  1. PERFORM ACTIVE TEST USING GTS

(a) Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Extended Illumination 1

Turns on the following lights:

  • No. 2 Interior Illumination Light Assembly (for Front Passenger Side) (No. 2 Instrument Panel Garnish Sub-assembly)

OFF or ON

Perform the Active Test with the Toyota Prius vehicle stopped and ignition switch ON.

Extended Illumination 2

Turns on the following lights:

  • No. 1 Interior Illumination Light Assembly (No. 1 Instrument Panel Garnish Sub-assembly)
  • No. 2 Interior Illumination Light Assembly (for Center) (No. 2 Instrument Panel Garnish Sub-assembly)

OFF or ON

Perform the Active Test with the Toyota Prius vehicle stopped and ignition switch ON.

Body Electrical > Main Body > Active Test

Extended Illumination 1

Body Electrical > Main Body > Active Test

Extended Illumination 2

Result

Proceed to

OK

A

NG (No. 2 interior illumination light assembly (for front passenger side) (No. 2 instrument panel garnish sub-assembly) does not come on)

B

NG (No. 1 interior illumination light assembly (No. 1 instrument panel garnish sub-assembly) does not come on)

C

NG (No. 2 interior illumination light assembly (for center) (No. 2 instrument panel garnish sub-assembly) does not come on)

D

NG (No. 1 interior illumination light assembly (No. 1 instrument panel garnish sub-assembly) and No. 2 interior illumination light assembly (for center) (No. 2 instrument panel garnish sub-assembly) do not come on)

E

NG (All lights do not come on)

F

A

USE SIMULATION METHOD TO CHECK

C

GO TO STEP 6

D

GO TO STEP 9

E

GO TO STEP 12

F

GO TO STEP 14

B
  1. INSPECT NO. 2 INTERIOR ILLUMINATION LIGHT ASSEMBLY (for FRONT PASSENGER SIDE) (NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY)

Click here

NG

REPLACE NO. 2 INTERIOR ILLUMINATION LIGHT ASSEMBLY (for FRONT PASSENGER SIDE) (NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY)

OK
  1. CHECK HARNESS AND CONNECTOR (NO. 2 INTERIOR ILLUMINATION LIGHT ASSEMBLY (for FRONT PASSENGER SIDE) - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

(a) Disconnect the K16 main body ECU (multiplex network body ECU) connector.

(b) Disconnect the K51 No. 2 interior illumination light assembly (for front passenger side) (No. 2 instrument panel garnish sub-assembly) connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(K16,K51) Click Connector(K16) Click Connector(K51)

Tester Connection

Condition

Specified Condition

K16-10 (LED1) - K51-1 (E)

Always

Below 1 Ω

K16-10 (LED1) or K51-1 (E) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (NO. 2 INTERIOR ILLUMINATION LIGHT ASSEMBLY (for FRONT PASSENGER SIDE) - POWER DISTRIBUTION BOX ASSEMBLY)

(a) Disconnect the K20 power distribution box assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(K51,K20) Click Connector(K51) Click Connector(K20)

Tester Connection

Condition

Specified Condition

K51-5 (B) - K20-44

Always

Below 1 Ω

K51-5 (B) or K20-44 - Body ground

Always

10 kΩ or higher

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. INSPECT NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY (NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY)

Click here

NG

REPLACE NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY (NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY)

OK
  1. CHECK HARNESS AND CONNECTOR (NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

(a) Disconnect the K16 main body ECU (multiplex network body ECU) connector.

(b) Disconnect the K52 No. 1 interior illumination light assembly (No. 1 instrument panel garnish sub-assembly) connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(K16,K52) Click Connector(K16) Click Connector(K52)

Tester Connection

Condition

Specified Condition

K16-14 (LED2) - K52-1 (E)

Always

Below 1 Ω

K16-14 (LED2) or K52-1 (E) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY - POWER DISTRIBUTION BOX ASSEMBLY)

(a) Disconnect the K20 power distribution box assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(K52,K20) Click Connector(K52) Click Connector(K20)

Tester Connection

Condition

Specified Condition

K52-5 (B) - K20-44

Always

Below 1 Ω

K52-5 (B) or K20-44 - Body ground

Always

10 kΩ or higher

OK

USE SIMULATION METHOD TO CHECK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. INSPECT NO. 2 INTERIOR ILLUMINATION LIGHT ASSEMBLY (for CENTER) (NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY)

Click here

NG

REPLACE NO. 2 INTERIOR ILLUMINATION LIGHT ASSEMBLY (for CENTER) (NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY)

OK
  1. CHECK HARNESS AND CONNECTOR (NO. 2 INTERIOR ILLUMINATION LIGHT ASSEMBLY (for CENTER) - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

(a) Disconnect the K16 main body ECU (multiplex network body ECU) connector.

(b) Disconnect the K95 No. 2 interior illumination light assembly (for center) (No. 2 instrument panel garnish sub-assembly) connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(K16,K95) Click Connector(K16) Click Connector(K95)

Tester Connection

Condition

Specified Condition

K16-14 (LED2) - K95-1 (E)

Always

Below 1 Ω

K16-14 (LED2) or K95-1 (E) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (NO. 2 INTERIOR ILLUMINATION LIGHT ASSEMBLY (for CENTER) - POWER DISTRIBUTION BOX ASSEMBLY)

(a) Disconnect the K20 power distribution box assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(K95,K20) Click Connector(K95) Click Connector(K20)

Tester Connection

Condition

Specified Condition

K95-5 (B) - K20-44

Always

Below 1 Ω

K95-5 (B) or K20-44 - Body ground

Always

10 kΩ or higher

OK

USE SIMULATION METHOD TO CHECK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. CHECK HARNESS AND CONNECTOR (NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

(a) Disconnect the K16 main body ECU (multiplex network body ECU) connector.

(b) Disconnect the K52 No. 1 interior illumination light assembly (No. 1 instrument panel garnish sub-assembly) connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(K16,K52) Click Connector(K16) Click Connector(K52)

Tester Connection

Condition

Specified Condition

K16-14 (LED2) - K52-1 (E)

Always

Below 1 Ω

K16-14 (LED2) or K52-1 (E) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY - POWER DISTRIBUTION BOX ASSEMBLY)

(a) Disconnect the K20 power distribution box assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(K52,K20) Click Connector(K52) Click Connector(K20)

Tester Connection

Condition

Specified Condition

K52-5 (B) - K20-44

Always

Below 1 Ω

K52-5 (B) or K20-44 - Body ground

Always

10 kΩ or higher

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - POWER SOURCE)

(a) Disconnect the A15 power distribution box assembly connectors.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Click Location & Routing(A15) Click Connector(A15)

Tester Connection

Condition

Specified Condition

A15-1 - Body ground

Ignition switch off

11 to 14 V

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. INSPECT POWER DISTRIBUTION BOX ASSEMBLY

(a) Disconnect the K20 power distribution box assembly connectors.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(A15,K20) Click Connector(A15) Click Connector(K20)

Tester Connection

Condition

Specified Condition

A15-1 - K20-44

Always

Below 1 Ω

NG

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

OK
  1. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - ILLUMINATION LIGHTS)

(a) Disconnect the K16 main body ECU (multiplex network body ECU) connector.

(b) Disconnect the K51 No. 2 interior illumination light assembly (for front passenger side) (No. 2 instrument panel garnish sub-assembly) connector.

(c) Disconnect the K52 No. 1 interior illumination light assembly (No. 1 instrument panel garnish sub-assembly) connector.

(d) Disconnect the K95 No. 2 interior illumination light assembly (for center) (No. 2 instrument panel garnish sub-assembly) connector.

(e) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(K16,K51,K52,K95) Click Connector(K16) Click Connector(K51) Click Connector(K52) Click Connector(K95)

Tester Connection

Condition

Specified Condition

K16-10 (LED1) - K51-1 (E)

Always

Below 1 Ω

K16-14 (LED2) - K52-1 (E)

Always

Below 1 Ω

K16-14 (LED2) - K95-1 (E)

Always

Below 1 Ω

K16-10 (LED1) or K51-1 (E) - Body ground

Always

10 kΩ or higher

K16-14 (LED2) or K52-1 (E) - Body ground

Always

10 kΩ or higher

K16-14 (LED2) or K95-1 (E) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (ILLUMINATION LIGHTS - POWER DISTRIBUTION BOX ASSEMBLY)

(a) Disconnect the K20 power distribution box assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(K51,K20,K52,K95) Click Connector(K51) Click Connector(K20) Click Connector(K52) Click Connector(K95)

Tester Connection

Condition

Specified Condition

K51-5 (B) - K20-44

Always

Below 1 Ω

K52-5 (B) - K20-44

Always

Below 1 Ω

K95-5 (B) - K20-44

Always

Below 1 Ω

K51-5 (B) or K20-44 - Body ground

Always

10 kΩ or higher

K52-5 (B) or K20-44 - Body ground

Always

10 kΩ or higher

K95-5 (B) or K20-44 - Body ground

Always

10 kΩ or higher

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

Push Start Switch Illumination Circuit

DESCRIPTION

The illuminated entry system controls the push start switch illumination.

WIRING DIAGRAM

NOTICE:

Before replacing the certification ECU (smart key ECU assembly), refer to Registration.

Click here

PROCEDURE

  1. PERFORM ACTIVE TEST USING GTS

(a) Perform the Active Test according to the display on the GTS.

Body Electrical > Smart Key > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Start SW Light Power Supply

Push start switch illumination

OFF or ON

-

Body Electrical > Smart Key > Active Test

Start SW Light Power Supply

OK:

Push start switch illumination comes on.

OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG
  1. INSPECT PUSH START SWITCH

for M20A-FXS: Click here

for 2ZR-FXE: Click here

NG

REPLACE PUSH START SWITCH

for M20A-FXS: Click here

for 2ZR-FXE: Click here

OK
  1. CHECK HARNESS AND CONNECTOR (PUSH START SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

(a) Disconnect the K13 certification ECU (smart key ECU assembly) connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(K66,K13) Click Connector(K66) Click Connector(K13)

Tester Connection

Condition

Specified Condition

K66-5(SWIL) - K13-20(SWIL)

Always

Below 1 Ω

K66-3(GND) - K13-30(AGND)

Always

Below 1 Ω

K66-5(SWIL) or K13-20(SWIL) - Body ground

Always

10 kΩ or higher

K66-3(GND) or K13-30(AGND) - Body ground

Always

10 kΩ or higher

OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

Instrument Panel Illumination does not Turn On

DESCRIPTION

The main body ECU (multiplex network body ECU) controls the instrument panel illuminations.

WIRING DIAGRAM

NOTICE:

  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  • First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CXPI communication malfunctions before troubleshooting this symptom.

    Click here

PROCEDURE

  1. READ VALUE USING GTS

(a) Turn the light control switch to the TAIL position.

(b) Read the Data List according to the display on the GTS.

Body Electrical > Power Distribution Box > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Panel Light Fuse Shut Off Status

Panel light fuse condition

OFF or ON

OFF: Fuse not shut off

ON: Fuse shut off

-

Body Electrical > Power Distribution Box > Data List

Panel Light Fuse Shut Off Status

OK:

The Data List value displays "OFF".

NG

GO TO STEP 5

OK
  1. READ VALUE USING GTS

(a) Read the Data List according to the display on the GTS.

Body Electrical > Power Distribution Box > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Panel Light Input Signal

Panel light input condition

OFF or ON

OFF: Light control switch not in tail position

ON: Light control switch in tail position

-

Body Electrical > Power Distribution Box > Data List

Panel Light Input Signal

OK:

The GTS display changes correctly in response to the operation of the light control switch.

NG

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

OK
  1. READ VALUE USING GTS

(a) Read the Data List according to the display on the GTS.

Body Electrical > Power Distribution Box > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Panel Light Output Signal

Panel light output condition

OFF or ON

OFF: Panel light off

ON: Panel light on

-

Body Electrical > Power Distribution Box > Data List

Panel Light Output Signal

OK:

The GTS display changes correctly in response to the operation of the light control switch.

NG

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

OK
  1. CHECK HARNESS AND CONNECTOR

(a) Disconnect the M3 rear power window regulator switch assembly (LH) connector.

(b) Disconnect the L3 rear power window regulator switch assembly (RH) connector.

(c) Disconnect the O8 multiplex network master switch assembly connector.

(d) Disconnect the O13 outer mirror switch assembly connector.

(e) w/ Door Control Switch Assembly

(1) Disconnect the N10 door control switch assembly connector.

(f) Disconnect the N11 power window regulator switch assembly connector.

(g) w/ Rear Seat Heater

(1) Disconnect the K29 rear seat heater switch (RH) connector.

(2) Disconnect the K30 rear seat heater switch (LH) connector.

(h) Disconnect the K33 No. 1 interior illumination light assembly connector.

(i) w/ Advanced Park

(1) Disconnect the K34 IPA main switch assembly connector.

(j) Disconnect the K22 electric parking brake switch assembly connector.

(k) w/ Heated Steering Heater System

(1) Disconnect the K87 steering heater switch connector.

(l) Disconnect the K50 fuel lid opener switch connector.

(m) Disconnect the K80 radio and display receiver assembly connector.

(n) Disconnect the K68 air conditioning control assembly connector.

(o) w/ Manual Headlight Leveling System

(1) Disconnect the K97 headlight leveling switch connector.

(p) Disconnect the U1 map light assembly connector.

(q) w/ Panoramic View Monitor System

(1) Disconnect the K49 panoramic view monitor switch connector.

(r) w/ Power Back Door System

(1) Disconnect the K65 power back door control switch connector.

(s) w/ Accessory Power Outlet System

(1) Disconnect the K32 power outlet switch connector.

(t) w/ Windshield Deicer System

(1) Disconnect the K31 front window deicer switch connector.

(u) w/ Wireless Charging System

(1) Disconnect the K46 mobile wireless charger cradle assembly connector.

(v) Disconnect the K77 auto high beam switch connector.

(w) Disconnect the K69 hazard warning signal switch assembly connector.

(x) Disconnect the K64 trip switch connector.

(y) Disconnect the z6 steering pad switch connector.

(z) Disconnect the K96 spiral cable sub-assembly connector.

(aa) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(M3,R17,L3,O8,O13,N10,N11,K29,K21,K30,K33,K34,K22,K87,K50,K80,K68,K97,U1,K49,K65,K32,K31,K46,K77,K69,K64,z6,K96) Click Connector(M3) Click Connector(R17) Click Connector(L3) Click Connector(O8) Click Connector(O13) Click Connector(N10) Click Connector(N11) Click Connector(K29) Click Connector(K21) Click Connector(K30) Click Connector(K33) Click Connector(K34) Click Connector(K22) Click Connector(K87) Click Connector(K50) Click Connector(K80) Click Connector(K68) Click Connector(K97) Click Connector(U1) Click Connector(K49) Click Connector(K65) Click Connector(K32) Click Connector(K31) Click Connector(K46) Click Connector(K77) Click Connector(K69) Click Connector(K64) Click Connector(z6) Click Connector(K96)

Tester Connection

Condition

Specified Condition

*1: w/ Rear Seat Heater

*2: w/ Advanced Park

*3: w/ Heated Steering Heater System

*4: w/ Manual Headlight Leveling System

*5: w/ Panoramic View Monitor System

*6: w/ Power Back Door System

*7: w/ Windshield Deicer System

*8: w/ Wireless Charging System

*9: w/ Accessory Power Outlet System

*10: w/ Door Control Switch Assembly

M3-3 (ILL ) - R17-9

Always

Below 1 Ω

L3-3 (ILL ) - R17-9

Always

Below 1 Ω

O8-8 (ILL ) - R17-9

Always

Below 1 Ω

O13-12 (ILL ) - R17-9

Always

Below 1 Ω

N10-3 (ILL ) - R17-9*10

Always

Below 1 Ω

N11-6 (ILL ) - R17-9

Always

Below 1 Ω

K29-6 (ILL ) - K21-2*1

Always

Below 1 Ω

K30-6 (ILL ) - K21-2*1

Always

Below 1 Ω

K33-2 (B) - K21-2

Always

Below 1 Ω

K34-6 (ILL ) - K21-2*2

Always

Below 1 Ω

K22-10 (ILL ) - K21-2

Always

Below 1 Ω

K87-6 (ILL ) - K21-2*3

Always

Below 1 Ω

K50-6 (ILL ) - K21-2

Always

Below 1 Ω

K80-25 (ILL ) - K21-2

Always

Below 1 Ω

K68-6 (ILL ) - K21-2

Always

Below 1 Ω

K97-6 (ILL ) - K21-2*4

Always

Below 1 Ω

U1-2 (ILLB) - K21-2

Always

Below 1 Ω

K49-6 (ILL ) - K21-2*5

Always

Below 1 Ω

K65-6 (ILL ) - K21-2*6

Always

Below 1 Ω

K32-6 (ILL ) - K21-2*9

Always

Below 1 Ω

K31-6 (ILL ) - K21-2*7

Always

Below 1 Ω

K46-7 (TAIL) - K21-2*8

Always

Below 1 Ω

K77-6 (ILL ) - K21-2

Always

Below 1 Ω

K69-7 (ILL ) - K21-2

Always

Below 1 Ω

K64-3 (ILL ) - K21-2

Always

Below 1 Ω

z6-1 - K21-2

Always

Below 1 Ω

K96-14 (IL 2) - K21-2

Always

Below 1 Ω

OK

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (LH)

(a) Disconnect the M3 rear power window regulator switch assembly (LH) connector.

(b) Turn the light control switch to the TAIL position.

(c) Read the Data List according to the display on the GTS.

Body Electrical > Power Distribution Box > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Panel Light Fuse Shut Off Status

Panel light fuse condition

OFF or ON

OFF: Fuse not shut off

ON: Fuse shut off

-

Body Electrical > Power Distribution Box > Data List

Panel Light Fuse Shut Off Status

OK:

The Data List value displays "OFF".

OK

REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (LH)

NG
  1. INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (RH)

(a) Disconnect the L3 rear power window regulator switch assembly (RH) connector.

(b) Turn the light control switch to the TAIL position.

(c) Read the Data List according to the display on the GTS.

Body Electrical > Power Distribution Box > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Panel Light Fuse Shut Off Status

Panel light fuse condition

OFF or ON

OFF: Fuse not shut off

ON: Fuse shut off

-

Body Electrical > Power Distribution Box > Data List

Panel Light Fuse Shut Off Status

OK:

The Data List value displays "OFF".

OK

REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (RH)

NG
  1. INSPECT MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

(a) Disconnect the O8 multiplex network master switch assembly connector.

(b) Turn the light control switch to the TAIL position.

(c) Read the Data List according to the display on the GTS.

Body Electrical > Power Distribution Box > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Panel Light Fuse Shut Off Status

Panel light fuse condition

OFF or ON

OFF: Fuse not shut off

ON: Fuse shut off

-

Body Electrical > Power Distribution Box > Data List

Panel Light Fuse Shut Off Status

OK:

The Data List value displays "OFF".

OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG
  1. INSPECT OUTER MIRROR SWITCH ASSEMBLY (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)

(a) Disconnect the O13 outer mirror switch assembly connector.

(b) Turn the light control switch to the TAIL position.

(c) Read the Data List according to the display on the GTS.

Body Electrical > Power Distribution Box > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Panel Light Fuse Shut Off Status

Panel light fuse condition

OFF or ON

OFF: Fuse not shut off

ON: Fuse shut off

-

Body Electrical > Power Distribution Box > Data List

Panel Light Fuse Shut Off Status

OK:

The Data List value displays "OFF".

OK

REPLACE OUTER MIRROR SWITCH ASSEMBLY (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)

NG
  1. CONFIRM MODEL

Result

Proceed to

w/o Door Control Switch Assembly

A

w/ Door Control Switch Assembly

B

A

GO TO STEP 11

B
  1. INSPECT DOOR CONTROL SWITCH ASSEMBLY

(a) Disconnect the N10 door control switch assembly connector.

(b) Turn the light control switch to the TAIL position.

(c) Read the Data List according to the display on the GTS.

Body Electrical > Power Distribution Box > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Panel Light Fuse Shut Off Status

Panel light fuse condition

OFF or ON

OFF: Fuse not shut off

ON: Fuse shut off

-

Body Electrical > Power Distribution Box > Data List

Panel Light Fuse Shut Off Status

OK:

The Data List value displays "OFF".

OK

REPLACE DOOR CONTROL SWITCH ASSEMBLY

NG
  1. INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY

(a) Disconnect the N11 power window regulator switch assembly connector.

(b) Turn the light control switch to the TAIL position.

(c) Read the Data List according to the display on the GTS.

Body Electrical > Power Distribution Box > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Panel Light Fuse Shut Off Status

Panel light fuse condition

OFF or ON

OFF: Fuse not shut off

ON: Fuse shut off

-

Body Electrical > Power Distribution Box > Data List

Panel Light Fuse Shut Off Status

OK:

The Data List value displays "OFF".

OK

REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY

NG
  1. CONFIRM MODEL

Result

Proceed to

w/o Rear Seat Heater

A

w/ Rear Seat Heater

B

A

GO TO STEP 15

B
  1. INSPECT REAR SEAT HEATER SWITCH (RH)

(a) Disconnect the K29 rear seat heater switch (RH) connector.

(b) Turn the light control switch to the TAIL position.

(c) Read the Data List according to the display on the GTS.

Body Electrical > Power Distribution Box > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Panel Light Fuse Shut Off Status

Panel light fuse condition

OFF or ON

OFF: Fuse not shut off

ON: Fuse shut off

-

Body Electrical > Power Distribution Box > Data List

Panel Light Fuse Shut Off Status

OK:

The Data List value displays "OFF".

OK

REPLACE REAR SEAT HEATER SWITCH (RH)

NG
  1. INSPECT REAR SEAT HEATER SWITCH (LH)

(a) Disconnect the K30 rear seat heater switch (LH) connector.

(b) Turn the light control switch to the TAIL position.

(c) Read the Data List according to the display on the GTS.

Body Electrical > Power Distribution Box > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Panel Light Fuse Shut Off Status

Panel light fuse condition

OFF or ON

OFF: Fuse not shut off

ON: Fuse shut off

-

Body Electrical > Power Distribution Box > Data List

Panel Light Fuse Shut Off Status

OK:

The Data List value displays "OFF".

OK

REPLACE REAR SEAT HEATER SWITCH (LH)

NG
  1. INSPECT NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY

(a) Disconnect the K33 No. 1 interior illumination light assembly connector.

(b) Turn the light control switch to the TAIL position.

(c) Read the Data List according to the display on the GTS.

Body Electrical > Power Distribution Box > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Panel Light Fuse Shut Off Status

Panel light fuse condition

OFF or ON

OFF: Fuse not shut off

ON: Fuse shut off

-

Body Electrical > Power Distribution Box > Data List

Panel Light Fuse Shut Off Status

OK:

The Data List value displays "OFF".

OK

REPLACE NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY

NG
  1. CONFIRM MODEL

Result

Proceed to

w/o Advanced Park

A

w/ Advanced Park

B

A

GO TO STEP 18

B
  1. INSPECT IPA MAIN SWITCH ASSEMBLY

(a) Disconnect the K34 IPA main switch assembly connector.

(b) Turn the light control switch to the TAIL position.

(c) Read the Data List according to the display on the GTS.

Body Electrical > Power Distribution Box > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Panel Light Fuse Shut Off Status

Panel light fuse condition

OFF or ON

OFF: Fuse not shut off

ON: Fuse shut off

-

Body Electrical > Power Distribution Box > Data List

Panel Light Fuse Shut Off Status

OK:

The Data List value displays "OFF".

OK

REPLACE IPA MAIN SWITCH ASSEMBLY

NG
  1. INSPECT ELECTRIC PARKING BRAKE SWITCH ASSEMBLY

(a) Disconnect the K22 electric parking brake switch assembly connector.

(b) Turn the light control switch to the TAIL position.

(c) Read the Data List according to the display on the GTS.

Body Electrical > Power Distribution Box > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Panel Light Fuse Shut Off Status

Panel light fuse condition

OFF or ON

OFF: Fuse not shut off

ON: Fuse shut off

-

Body Electrical > Power Distribution Box > Data List

Panel Light Fuse Shut Off Status

OK:

The Data List value displays "OFF".

OK

REPLACE ELECTRIC PARKING BRAKE SWITCH ASSEMBLY

NG
  1. CONFIRM MODEL

Result

Proceed to

w/o Heated Steering Heater System

A

w/ Heated Steering Heater System

B

A

GO TO STEP 21

B
  1. INSPECT STEERING HEATER SWITCH

(a) Disconnect the K87 steering heater switch connector.

(b) Turn the light control switch to the TAIL position.

(c) Read the Data List according to the display on the GTS.

Body Electrical > Power Distribution Box > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Panel Light Fuse Shut Off Status

Panel light fuse condition

OFF or ON

OFF: Fuse not shut off

ON: Fuse shut off

-

Body Electrical > Power Distribution Box > Data List

Panel Light Fuse Shut Off Status

OK:

The Data List value displays "OFF".

OK

REPLACE STEERING HEATER SWITCH

NG
  1. INSPECT FUEL LID OPENER SWITCH

(a) Disconnect the K50 fuel lid opener switch connector.

(b) Turn the light control switch to the TAIL position.

(c) Read the Data List according to the display on the GTS.

Body Electrical > Power Distribution Box > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Panel Light Fuse Shut Off Status

Panel light fuse condition

OFF or ON

OFF: Fuse not shut off

ON: Fuse shut off

-

Body Electrical > Power Distribution Box > Data List

Panel Light Fuse Shut Off Status

OK:

The Data List value displays "OFF".

OK

REPLACE FUEL LID OPENER SWITCH

NG
  1. INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

(a) Disconnect the K80 radio and display receiver assembly connector.

(b) Turn the light control switch to the TAIL position.

(c) Read the Data List according to the display on the GTS.

Body Electrical > Power Distribution Box > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Panel Light Fuse Shut Off Status

Panel light fuse condition

OFF or ON

OFF: Fuse not shut off

ON: Fuse shut off

-

Body Electrical > Power Distribution Box > Data List

Panel Light Fuse Shut Off Status

OK:

The Data List value displays "OFF".

OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG
  1. INSPECT AIR CONDITIONING CONTROL ASSEMBLY

(a) Disconnect the K68 air conditioning control assembly connector.

(b) Turn the light control switch to the TAIL position.

(c) Read the Data List according to the display on the GTS.

Body Electrical > Power Distribution Box > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Panel Light Fuse Shut Off Status

Panel light fuse condition

OFF or ON

OFF: Fuse not shut off

ON: Fuse shut off

-

Body Electrical > Power Distribution Box > Data List

Panel Light Fuse Shut Off Status

OK:

The Data List value displays "OFF".

OK

REPLACE AIR CONDITIONING CONTROL ASSEMBLY

NG
  1. CONFIRM MODEL

Result

Proceed to

w/o Manual Headlight Leveling System

A

w/ Manual Headlight Leveling System

B

A

GO TO STEP 26

B
  1. INSPECT HEADLIGHT LEVELING SWITCH

(a) Disconnect the K97 headlight leveling switch connector.

(b) Turn the light control switch to the TAIL position.

(c) Read the Data List according to the display on the GTS.

Body Electrical > Power Distribution Box > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Panel Light Fuse Shut Off Status

Panel light fuse condition

OFF or ON

OFF: Fuse not shut off

ON: Fuse shut off

-

Body Electrical > Power Distribution Box > Data List

Panel Light Fuse Shut Off Status

OK:

The Data List value displays "OFF".

OK

REPLACE HEADLIGHT LEVELING SWITCH

NG
  1. INSPECT MAP LIGHT ASSEMBLY

(a) Disconnect the U1 map light assembly connector.

(b) Turn the light control switch to the TAIL position.

(c) Read the Data List according to the display on the GTS.

Body Electrical > Power Distribution Box > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Panel Light Fuse Shut Off Status

Panel light fuse condition

OFF or ON

OFF: Fuse not shut off

ON: Fuse shut off

-

Body Electrical > Power Distribution Box > Data List

Panel Light Fuse Shut Off Status

OK:

The Data List value displays "OFF".

OK

REPLACE MAP LIGHT ASSEMBLY

NG
  1. CONFIRM MODEL

Result

Proceed to

w/o Panoramic View Monitor System

A

w/ Panoramic View Monitor System

B

A

GO TO STEP 29

B
  1. INSPECT PANORAMIC VIEW MONITOR SWITCH

(a) Disconnect the K49 panoramic view monitor switch connector.

(b) Turn the light control switch to the TAIL position.

(c) Read the Data List according to the display on the GTS.

Body Electrical > Power Distribution Box > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Panel Light Fuse Shut Off Status

Panel light fuse condition

OFF or ON

OFF: Fuse not shut off

ON: Fuse shut off

-

Body Electrical > Power Distribution Box > Data List

Panel Light Fuse Shut Off Status

OK:

The Data List value displays "OFF".

OK

REPLACE PANORAMIC VIEW MONITOR SWITCH

NG
  1. CONFIRM MODEL

Result

Proceed to

w/o Power Back Door System

A

w/ Power Back Door System

B

A

GO TO STEP 31

B
  1. INSPECT POWER BACK DOOR CONTROL SWITCH

(a) Disconnect the K65 power back door control switch connector.

(b) Turn the light control switch to the TAIL position.

(c) Read the Data List according to the display on the GTS.

Body Electrical > Power Distribution Box > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Panel Light Fuse Shut Off Status

Panel light fuse condition

OFF or ON

OFF: Fuse not shut off

ON: Fuse shut off

-

Body Electrical > Power Distribution Box > Data List

Panel Light Fuse Shut Off Status

OK:

The Data List value displays "OFF".

OK

REPLACE POWER BACK DOOR CONTROL SWITCH

NG
  1. CONFIRM MODEL

Result

Proceed to

w/o Accessory Power Outlet System

A

w/ Accessory Power Outlet System

B

A

GO TO STEP 33

B
  1. INSPECT POWER OUTLET SWITCH

(a) Disconnect the K32 power outlet switch connector.

(b) Turn the light control switch to the TAIL position.

(c) Read the Data List according to the display on the GTS.

Body Electrical > Power Distribution Box > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Panel Light Fuse Shut Off Status

Panel light fuse condition

OFF or ON

OFF: Fuse not shut off

ON: Fuse shut off

-

Body Electrical > Power Distribution Box > Data List

Panel Light Fuse Shut Off Status

OK:

The Data List value displays "OFF".

OK

REPLACE POWER OUTLET SWITCH

NG
  1. CONFIRM MODEL

Result

Proceed to

w/o Windshield Deicer System

A

w/ Windshield Deicer System

B

A

GO TO STEP 35

B
  1. INSPECT FRONT WINDOW DEICER SWITCH

(a) Disconnect the K31 front window deicer switch connector.

(b) Turn the light control switch to the TAIL position.

(c) Read the Data List according to the display on the GTS.

Body Electrical > Power Distribution Box > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Panel Light Fuse Shut Off Status

Panel light fuse condition

OFF or ON

OFF: Fuse not shut off

ON: Fuse shut off

-

Body Electrical > Power Distribution Box > Data List

Panel Light Fuse Shut Off Status

OK:

The Data List value displays "OFF".

OK

REPLACE FRONT WINDOW DEICER SWITCH

NG
  1. CONFIRM MODEL

Result

Proceed to

w/o Wireless Charging System

A

w/ Wireless Charging System

B

A

GO TO STEP 37

B
  1. INSPECT MOBILE WIRELESS CHARGER CRADLE ASSEMBLY

(a) Disconnect the K46 mobile wireless charger cradle assembly connector.

(b) Turn the light control switch to the TAIL position.

(c) Read the Data List according to the display on the GTS.

Body Electrical > Power Distribution Box > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Panel Light Fuse Shut Off Status

Panel light fuse condition

OFF or ON

OFF: Fuse not shut off

ON: Fuse shut off

-

Body Electrical > Power Distribution Box > Data List

Panel Light Fuse Shut Off Status

OK:

The Data List value displays "OFF".

OK

REPLACE MOBILE WIRELESS CHARGER CRADLE ASSEMBLY

NG
  1. INSPECT AUTO HIGH BEAM SWITCH

(a) Disconnect the K77 auto high beam switch connector.

(b) Turn the light control switch to the TAIL position.

(c) Read the Data List according to the display on the GTS.

Body Electrical > Power Distribution Box > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Panel Light Fuse Shut Off Status

Panel light fuse condition

OFF or ON

OFF: Fuse not shut off

ON: Fuse shut off

-

Body Electrical > Power Distribution Box > Data List

Panel Light Fuse Shut Off Status

OK:

The Data List value displays "OFF".

OK

REPLACE AUTO HIGH BEAM SWITCH

NG
  1. INSPECT HAZARD WARNING SIGNAL SWITCH ASSEMBLY

(a) Disconnect the K69 hazard warning signal switch assembly connector.

(b) Turn the light control switch to the TAIL position.

(c) Read the Data List according to the display on the GTS.

Body Electrical > Power Distribution Box > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Panel Light Fuse Shut Off Status

Panel light fuse condition

OFF or ON

OFF: Fuse not shut off

ON: Fuse shut off

-

Body Electrical > Power Distribution Box > Data List

Panel Light Fuse Shut Off Status

OK:

The Data List value displays "OFF".

OK

REPLACE HAZARD WARNING SIGNAL SWITCH ASSEMBLY

NG
  1. INSPECT TRIP SWITCH

(a) Disconnect the K64 trip switch connector.

(b) Turn the light control switch to the TAIL position.

(c) Read the Data List according to the display on the GTS.

Body Electrical > Power Distribution Box > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Panel Light Fuse Shut Off Status

Panel light fuse condition

OFF or ON

OFF: Fuse not shut off

ON: Fuse shut off

-

Body Electrical > Power Distribution Box > Data List

Panel Light Fuse Shut Off Status

OK:

The Data List value displays "OFF".

OK

REPLACE TRIP SWITCH

NG
  1. INSPECT STEERING PAD SWITCH ASSEMBLY

(a) Disconnect the z6 steering pad switch assembly connector.

(b) Turn the light control switch to the TAIL position.

(c) Read the Data List according to the display on the GTS.

Body Electrical > Power Distribution Box > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Panel Light Fuse Shut Off Status

Panel light fuse condition

OFF or ON

OFF: Fuse not shut off

ON: Fuse shut off

-

Body Electrical > Power Distribution Box > Data List

Panel Light Fuse Shut Off Status

OK:

The Data List value displays "OFF".

OK

REPLACE STEERING PAD SWITCH ASSEMBLY

NG
  1. INSPECT SPIRAL CABLE SUB-ASSEMBLY

(a) Disconnect the K96 spiral cable sub-assembly connector.

(b) Turn the light control switch to the TAIL position.

(c) Read the Data List according to the display on the GTS.

Body Electrical > Power Distribution Box > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Panel Light Fuse Shut Off Status

Panel light fuse condition

OFF or ON

OFF: Fuse not shut off

ON: Fuse shut off

-

Body Electrical > Power Distribution Box > Data List

Panel Light Fuse Shut Off Status

OK:

The Data List value displays "OFF".

OK

REPLACE SPIRAL CABLE SUB-ASSEMBLY

NG
  1. CHECK HARNESS AND CONNECTOR

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(M3,R17,L3,O8,O13,N10,N11,K29,K21,K30,K33,K34,K22,K87,K50,K80,K68,K97,U1,K49,K65,K32,K31,K46,K77,K69,K64,z6,K96) Click Connector(M3) Click Connector(R17) Click Connector(L3) Click Connector(O8) Click Connector(O13) Click Connector(N10) Click Connector(N11) Click Connector(K29) Click Connector(K21) Click Connector(K30) Click Connector(K33) Click Connector(K34) Click Connector(K22) Click Connector(K87) Click Connector(K50) Click Connector(K80) Click Connector(K68) Click Connector(K97) Click Connector(U1) Click Connector(K49) Click Connector(K65) Click Connector(K32) Click Connector(K31) Click Connector(K46) Click Connector(K77) Click Connector(K69) Click Connector(K64) Click Connector(z6) Click Connector(K96)

Tester Connection

Condition

Specified Condition

*1: w/ Rear Seat Heater

*2: w/ Advanced Park

*3: w/ Heated Steering Heater System

*4: w/ Manual Headlight Leveling System

*5: w/ Panoramic View Monitor System

*6: w/ Power Back Door System

*7: w/ Windshield Deicer System

*8: w/ Wireless Charging System

*9: w/ Accessory Power Outlet System

*10: w/ Door Control Switch Assembly

M3-3 (ILL ) or R17-9 - Body ground

Always

10 kΩ or higher

L3-3 (ILL ) or R17-9 - Body ground

Always

10 kΩ or higher

O8-8 (ILL ) or R17-9 - Body ground

Always

10 kΩ or higher

O13-12 (ILL ) or R17-9 - Body ground

Always

10 kΩ or higher

N10-3 (ILL ) or R17-9 - Body ground*10

Always

10 kΩ or higher

N11-6 (ILL ) or R17-9 - Body ground

Always

10 kΩ or higher

K29-6 (ILL ) or K21-2 - Body ground*1

Always

10 kΩ or higher

K30-6 (ILL ) or K21-2 - Body ground*1

Always

10 kΩ or higher

K33-2 (B) or K21-2 - Body ground

Always

10 kΩ or higher

K34-6 (ILL ) or K21-2 - Body ground*2

Always

10 kΩ or higher

K22-10 (ILL ) or K21-2 - Body ground

Always

10 kΩ or higher

K87-6 (ILL ) or K21-2 - Body ground*3

Always

10 kΩ or higher

K50-6 (ILL ) or K21-2 - Body ground

Always

10 kΩ or higher

K80-25 (ILL ) or K21-2 - Body ground

Always

10 kΩ or higher

K68-6 (ILL ) or K21-2 - Body ground

Always

10 kΩ or higher

K97-6 (ILL ) or K21-2 - Body ground*4

Always

10 kΩ or higher

U1-2 (ILLB) or K21-2 - Body ground

Always

10 kΩ or higher

K49-6 (ILL ) or K21-2 - Body ground*5

Always

10 kΩ or higher

K65-6 (ILL ) or K21-2 - Body ground*6

Always

10 kΩ or higher

K32-6 (ILL ) or K21-2 - Body ground*9

Always

10 kΩ or higher

K31-6 (ILL ) or K21-2 - Body ground*7

Always

10 kΩ or higher

K46-7 (TAIL) or K21-2 - Body ground*8

Always

10 kΩ or higher

K77-6 (ILL ) or K21-2 - Body ground

Always

10 kΩ or higher

K69-7 (ILL ) or K21-2 - Body ground

Always

10 kΩ or higher

K64-3 (ILL ) or K21-2 - Body ground

Always

10 kΩ or higher

z6-1 or K21-2 - Body ground

Always

10 kΩ or higher

K96-14 (IL 2) or K21-2 - Body ground

Always

10 kΩ or higher

OK

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

Door Unlock Detection Switch Circuit

DESCRIPTION

The main body ECU (multiplex network body ECU) detects the condition of each door unlock detection switch.

WIRING DIAGRAM

NOTICE:

Before replacing the main body ECU (multiplex network body ECU), refer to Registration.

Click here

PROCEDURE

  1. READ VALUE USING GTS

(a) Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

FR Door Lock Position Switch Status

Front door RH unlock detection switch signal

LOCK or UNLOCK

LOCK: Front door RH locked

UNLOCK: Front door RH unlocked

-

FL Door Lock Position Switch Status

Front door LH unlock detection switch signal

LOCK or UNLOCK

LOCK: Front door LH locked

UNLOCK: Front door LH unlocked

-

RR Door Lock Position Switch Status

Rear door RH unlock detection switch signal

LOCK or UNLOCK

ON: Rear door RH unlocked

OFF: Rear door RH locked

-

RL Door Lock Position Switch Status

Rear door LH unlock detection switch signal

LOCK or UNLOCK

ON: Rear door LH unlocked

OFF: Rear door LH locked

-

Body Electrical > Main Body > Data List

Tester Display

FR Door Lock Position Switch Status

FL Door Lock Position Switch Status

RR Door Lock Position Switch Status

RL Door Lock Position Switch Status

OK:

Normal conditions listed above are displayed.

Result

Proceed to

OK

A

NG ("FR Door Lock Position Switch Status" is not normal)

B

NG ("FL Door Lock Position Switch Status" is not normal)

C

NG ("RR Door Lock Position Switch Status" is not normal)

D

NG ("RL Door Lock Position Switch Status" is not normal)

E

A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

C

GO TO STEP 4

D

GO TO STEP 6

E

GO TO STEP 8

B
  1. INSPECT FRONT DOOR LOCK WITH MOTOR ASSEMBLY RH

Click here

NG

REPLACE FRONT DOOR LOCK WITH MOTOR ASSEMBLY RH

OK
  1. CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK WITH MOTOR ASSEMBLY RH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) OR BODY GROUND)

(a) Disconnect the K17 main body ECU (multiplex network body ECU) connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(N2,K17) Click Connector(N2) Click Connector(K17)

Tester Connection

Condition

Specified Condition

N2-7 (LSSR) - K17-3 (LSFR)

Always

Below 1 Ω

N2-7 (LSSR) or K17-3 (LSFR) - Body ground

Always

10 kΩ or higher

N2-5 (E) - Body ground

Always

Below 1 Ω

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. INSPECT FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH

Click here

NG

REPLACE FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH

OK
  1. CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) OR BODY GROUND)

(a) Disconnect the K17 instrument panel junction block assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(O2,K17) Click Connector(O2) Click Connector(K17)

Tester Connection

Condition

Specified Condition

O2-8 (LSSR) - K17-9 (LSFL)

Always

Below 1 Ω

O2-8 (LSSR) or K17-9 (LSFL) - Body ground

Always

10 kΩ or higher

O2-10 (E) - Body ground

Always

Below 1 Ω

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. INSPECT REAR DOOR LOCK WITH MOTOR ASSEMBLY RH

Click here

NG

REPLACE REAR DOOR LOCK WITH MOTOR ASSEMBLY RH

OK
  1. CHECK HARNESS AND CONNECTOR (REAR DOOR LOCK WITH MOTOR ASSEMBLY RH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) OR BODY GROUND)

(a) Disconnect the K16 main body ECU (multiplex network body ECU) connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(L1,K16) Click Connector(L1) Click Connector(K16)

Tester Connection

Condition

Specified Condition

L1-9 (LSSR) - K16-23 (LSWR)

Always

Below 1 Ω

L1-9 (LSSR) or K16-23 (LSWR) - Body ground

Always

10 kΩ or higher

L1-6 (E) - Body ground

Always

Below 1 Ω

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. INSPECT REAR DOOR LOCK WITH MOTOR ASSEMBLY LH

Click here

NG

REPLACE REAR DOOR LOCK WITH MOTOR ASSEMBLY LH

OK
  1. CHECK HARNESS AND CONNECTOR (REAR DOOR LOCK WITH MOTOR ASSEMBLY LH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) OR BODY GROUND)

(a) Disconnect the K17 instrument panel junction block assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(M1,K17) Click Connector(M1) Click Connector(K17)

Tester Connection

Condition

Specified Condition

M1-6 (LSSR) - K17-10 (LSWL)

Always

Below 1 Ω

M1-6 (LSSR) or K17-10 (LSWL) - Body ground

Always

10 kΩ or higher

M1-9 (E) - Body ground

Always

Below 1 Ω

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR