Wheel Opening Moulding (for Rear Side)
- Removal
- Disassembly
- Reassembly
- Installation
Removal
REMOVAL
COMPONENTS (REMOVAL)
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
REAR WHEEL HOUSE FRONT PLATE |
65632D |
- |
- |
- |
2 |
QUARTER OUTSIDE MOULDING SUB-ASSEMBLY |
75606B |
- |
- |
|
PROCEDURE
1. REMOVE REAR WHEEL HOUSE FRONT PLATE
Click here ![]()
2. REMOVE QUARTER OUTSIDE MOULDING SUB-ASSEMBLY

(1) Apply protective tape around the quarter outside moulding sub-assembly as shown in the illustration.
(2) Remove the 2 clips and screw.
(b) for LH Side:

![]() |
Push |
![]() |
Place to Insert Hand |
![]() |
Remove in this Direction |
- |
- |
(1) As shown in the illustration, insert your hand between the "U" and "S" of the "PRIUS" and directly push the claw to disengage it.
NOTICE:
In order not to damage the claw, pull the quarter outer side moulding carefully.
(c) for RH Side:

![]() |
Push |
![]() |
Place to Insert Hand |
![]() |
Remove in this Direction |
- |
- |
(1) As shown in the illustration, insert your hand between the "P" and "R" of the "PRIUS" and directly push the claw to disengage it.
NOTICE:
In order not to damage the claw, pull the quarter outer side moulding carefully.

![]() |
Push |
![]() |
Place Hand Here |
![]() |
Remove in this Direction |
- |
- |
(1) Disengage the 3 claws by pushing the area indicated by the arrow in the illustration with a finger.
NOTICE:
To avoid damaging the claws, do not forcibly pull the quarter outside moulding sub-assembly.

![]() |
Place Hand Here |
![]() |
Remove in this Direction |
(1) Disengage the 2 clips as shown in the illustration.
NOTICE:
To prevent damage to the clips, make sure to pull the quarter outer side moulding evenly and straight.

![]() |
Place Hand Here |
![]() |
Remove in this Direction |
(1) Disengage the 7 clips as shown in the illustration to remove the quarter outside moulding sub-assembly.
Disassembly
DISASSEMBLY
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
NO. 1 BODY OUTSIDE MOULDING PAD |
75696 |
- |
- |
- |
2 |
REAR QUARTER MOULDING LOWER PROTECTOR |
75687 |
- |
- |
- |
● |
Non-reusable part |
- |
- |
PROCEDURE
1. REMOVE NO. 1 BODY OUTSIDE MOULDING PAD

2. REMOVE REAR QUARTER MOULDING LOWER PROTECTOR

Reassembly
REASSEMBLY
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
REAR QUARTER MOULDING LOWER PROTECTOR |
75687 |
- |
- |
|
2 |
NO. 1 BODY OUTSIDE MOULDING PAD |
75696 |
- |
- |
|
● |
Non-reusable part |
- |
- |
PROCEDURE
1. INSTALL REAR QUARTER MOULDING LOWER PROTECTOR

![]() |
Cleaning Area |
![]() |
Primer |
(1) Clean the quarter outside moulding sub-assembly surface.
1. Using a heat light, heat the double-sided tape remaining on the quarter outside moulding sub-assembly and rear quarter moulding lower protector.
Heating TemperatureArea | Temperature | Area | Temperature |
|---|---|---|---|
Quarter Outside Moulding Sub-assembly |
20 to 30 °C |
Rear Quarter Moulding Lower Protector |
20 to 30 °C |
CAUTION:
- Do not touch the heat light and heated parts, touching the heat light may result in burns.
- Touching heated parts for a long time may result in burns.

*a |
Heated Part |
*b |
Heat Light |
NOTICE:
Do not heat the quarter outside moulding sub-assembly excessively.
2. Remove any remaining double-sided tape from the quarter outside moulding sub-assembly.
3. Wipe off any tape adhesive residue with cleaner.
(2) Apply primer to the quarter outside moulding sub-assembly on the installation area of the rear quarter moulding lower protector.
1. Using a brush or felt, apply primer or equivalent to the rear quarter moulding lower protector installation area.
NOTICE:
- Replace the brush or felt if it is dirty or has become hardened.
- Do not apply primer to the painted side.
- Do not touch the quarter outside moulding sub-assembly until the primer has dried.
2. Let the primer dry sufficiently.
NOTICE:
Do not touch applied surfaces until the primer is dry.
Recommended drying time:
10 minutes or more (at 23 °C)
3. Confirm that the primer has completely dried by touching the quarter outside moulding sub-assembly. Then remove the tape.

*a |
Scribed Line |
- |
- |
Standard Measurement:
Area | Measurement | Area | Measurement |
|---|---|---|---|
A |
10.0 mm (0.394 in.) |
B |
3.0 mm (0.118 in.) |
(1) Install a new rear quarter moulding lower protector.
1. Using a heat light, heat the quarter outside moulding sub-assembly surface.
2. Remove the release paper from the rear quarter moulding lower protector.
HINT:
After removing the release paper, keep the exposed adhesive free from foreign matter.
3. Install the rear quarter moulding lower protector as shown in the illustration.
HINT:
- Apply the rear quarter moulding lower protector along the scribed line on the quarter outside moulding sub-assembly.
- Press the rear quarter moulding lower protector firmly to install it.
2. INSTALL NO. 1 BODY OUTSIDE MOULDING PAD

![]() |
Cleaning Area |
![]() |
Primer |
(1) Clean the quarter outside moulding sub-assembly surface.
1. Using a heat light, heat the double-sided tape remaining on the quarter outside moulding sub-assembly and No. 1 body outside moulding pad.
Heating TemperatureArea | Temperature | Area | Temperature |
|---|---|---|---|
Quarter Outside Moulding Sub-assembly |
20 to 30 °C |
No. 1 Body Outside Moulding Pad |
20 to 30 °C |
CAUTION:
- Do not touch the heat light and heated parts, touching the heat light may result in burns.
- Touching heated parts for a long time may result in burns.

*a |
Heated Part |
*b |
Heat Light |
NOTICE:
Do not heat the quarter outside moulding sub-assembly excessively.
2. Remove any remaining double-sided tape from the quarter outside moulding sub-assembly.
3. Wipe off any tape adhesive residue with cleaner.
(2) Apply primer to the quarter outside moulding sub-assembly on the installation area of the No. 1 body outside moulding pad.
1. Using a brush or felt, apply primer or equivalent to the No. 1 body outside moulding pad installation area.
NOTICE:
- Replace the brush or felt if it is dirty or has become hardened.
- Do not apply primer to the painted side.
- Do not touch the quarter outside moulding sub-assembly until the primer has dried.
2. Let the primer dry sufficiently.
NOTICE:
Do not touch applied surfaces until the primer is dry.
Recommended drying time:
10 minutes or more (at 23 °C)
3. Confirm that the primer has completely dried by touching the quarter outside moulding sub-assembly. Then remove the tape.

*a |
Scribed Line |
- |
- |
Standard Measurement:
Area | Measurement | Area | Measurement |
|---|---|---|---|
A |
3.0 mm (0.118 in.) |
B |
10.0 mm (0.394 in.) |
(1) Install a new No. 1 body outside moulding pad.
1. Using a heat light, heat the quarter outside moulding sub-assembly surface.
2. Remove the release paper from the No. 1 body outside moulding pad.
HINT:
After removing the release paper, keep the exposed adhesive free from foreign matter.
3. Install the No. 1 body outside moulding pad as shown in the illustration.
HINT:
- Apply the No. 1 body outside moulding pad along the scribed line on the quarter outside moulding sub-assembly.
- Press the No. 1 body outside moulding pad firmly to install it.
Installation
INSTALLATION
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
QUARTER OUTSIDE MOULDING SUB-ASSEMBLY |
75606B |
- |
- |
- |
2 |
REAR WHEEL HOUSE FRONT PLATE |
65632D |
- |
- |
- |
PROCEDURE
1. INSTALL QUARTER OUTSIDE MOULDING SUB-ASSEMBLY

2. INSTALL REAR WHEEL HOUSE FRONT PLATE































