Rocker Panel Moulding
- Removal
- Installation
Removal
REMOVAL
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
FRONT FENDER MOULDING SUB-ASSEMBLY |
75602A |
- |
- |
|
2 |
REAR WHEEL HOUSE FRONT PLATE |
65632D |
- |
- |
- |
3 |
QUARTER OUTSIDE MOULDING SUB-ASSEMBLY |
75606B |
- |
- |
|
4 |
BODY ROCKER PANEL MOULDING ASSEMBLY |
75860A |
- |
- |
|
5 |
ROCKER PANEL MOULDING FRONT END COVER |
75862E |
- |
- |
- |
PROCEDURE
1. DISCONNECT FRONT FENDER MOULDING SUB-ASSEMBLY

![]() |
Place Hand Here |
![]() |
Remove in this Direction (1) |
![]() |
Remove in this Direction (2) |
- |
- |
(1) Remove the 3 screws and clip.
(2) Disengage the 3 clips as shown in the illustration.
(3) Disengage the clip as shown in the illustration to disconnect the front fender moulding sub-assembly.
NOTICE:
To prevent damage to the clips, make sure to pull the front fender moulding sub-assembly evenly and straight.
2. REMOVE REAR WHEEL HOUSE FRONT PLATE
Click here ![]()
3. DISCONNECT QUARTER OUTSIDE MOULDING SUB-ASSEMBLY

![]() |
Place Hand Here |
![]() |
Remove in this Direction |
(1) Disengage the 2 clips as shown in the illustration.
NOTICE:
To prevent damage to the clips, make sure to pull the quarter outer side moulding evenly and straight.

![]() |
Place Hand Here |
![]() |
Remove in this Direction |
(1) Disengage the 3 clips as shown in the illustration to disconnect the quarter outside moulding sub-assembly.
4. REMOVE BODY ROCKER PANEL MOULDING ASSEMBLY

*a |
Clip (A) |
*b |
Clip (B) |
(1) Apply protective tape around the body rocker panel moulding assembly as shown in the illustration.
(2) Remove the 8 clips.

![]() |
Remove in this Direction |
- |
- |
(1) Remove the 2 screws.
(2) Disengage the 8 clips to remove the body rocker panel moulding assembly as shown in the illustration.
5. REMOVE ROCKER PANEL MOULDING FRONT END COVER

Installation
INSTALLATION
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
ROCKER PANEL MOULDING FRONT END COVER |
75862E |
- |
- |
- |
2 |
BODY ROCKER PANEL MOULDING ASSEMBLY |
75860A |
- |
- |
- |
3 |
QUARTER OUTSIDE MOULDING SUB-ASSEMBLY |
75606B |
- |
- |
- |
4 |
REAR WHEEL HOUSE FRONT PLATE |
65632D |
- |
- |
- |
5 |
FRONT FENDER MOULDING SUB-ASSEMBLY |
75602A |
- |
- |
- |
PROCEDURE
1. INSTALL ROCKER PANEL MOULDING FRONT END COVER
2. INSTALL BODY ROCKER PANEL MOULDING ASSEMBLY
3. CONNECT QUARTER OUTSIDE MOULDING SUB-ASSEMBLY
4. INSTALL REAR WHEEL HOUSE FRONT PLATE
5. CONNECT FRONT FENDER MOULDING SUB-ASSEMBLY
















