Thermostat
- Removal
- Inspection
- Installation
Removal
REMOVAL
COMPONENTS (REMOVAL)
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
NO. 1 ENGINE UNDER COVER ASSEMBLY |
51410 |
- |
- |
- |
2 |
DRAIN ENGINE COOLANT (for Engine) |
- |
- |
- |
|

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
3 |
RADIATOR SUPPORT OPENING COVER |
53289A |
- |
- |
- |
4 |
INLET NO. 2 AIR CLEANER |
17752 |
- |
- |
- |
5 |
AIR CLEANER CAP SUB-ASSEMBLY |
17705 |
- |
- |
- |
6 |
AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
17801 |
- |
- |
- |
7 |
AIR CLEANER CASE SUB-ASSEMBLY |
17701 |
- |
- |
- |
8 |
AIR CLEANER BRACKET |
17771A |
- |
- |
- |
9 |
INLET NO. 1 AIR CLEANER |
17751 |
- |
- |
- |

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
10 |
ENGINE OIL LEVEL DIPSTICK |
15301 |
- |
- |
- |
11 |
ENGINE OIL LEVEL DIPSTICK GUIDE |
11452 |
- |
- |
- |
12 |
WATER INLET WITH THERMOSTAT SUB-ASSEMBLY |
16031 |
- |
- |
|
*A |
Type A |
*B |
Type B |
*1 |
NO. 2 RADIATOR HOSE |
*2 |
NO. 3 WATER BY-PASS HOSE |
*3 |
GASKET |
*4 |
ENGINE OIL LEVEL DIPSTICK GUIDE O-RING |
● |
Non-reusable part |
- |
- |
PROCEDURE
1. REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY
Click here ![]()
2. DRAIN ENGINE COOLANT (for Engine)
Click here ![]()
3. REMOVE RADIATOR SUPPORT OPENING COVER
Click here ![]()
4. REMOVE INLET NO. 2 AIR CLEANER
Click here ![]()
5. REMOVE AIR CLEANER CAP SUB-ASSEMBLY
Click here ![]()
6. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
Click here ![]()
7. REMOVE AIR CLEANER CASE SUB-ASSEMBLY
Click here ![]()
8. REMOVE AIR CLEANER BRACKET
Click here ![]()
9. REMOVE INLET NO. 1 AIR CLEANER
Click here ![]()
10. REMOVE ENGINE OIL LEVEL DIPSTICK

11. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

12. REMOVE WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

*1 |
No. 2 Radiator Hose |
*2 |
No. 3 Water By-pass Hose |
(1) Slide the 2 clips and disconnect the No. 2 radiator hose and No. 3 water by-pass hose from the water inlet with thermostat sub-assembly.
NOTICE:
- Do not apply force to the water inlet with thermostat sub-assembly when disconnecting the No. 3 water by-pass hose.
- Do not damage the water inlet with thermostat sub-assembly.
HINT:
When disconnecting the No. 3 water by-pass hose, slide the clip, rotate the hose and pull it straight off the pipe.

*A |
Type A |
*B |
Type B |
Inspection
INSPECTION
PROCEDURE
1. INSPECT WATER INLET WITH THERMOSTAT SUB-ASSEMBLY
CAUTION:
- Do not put your hands into the water that has been heated for the inspection.
- Touching the heated water could result in burns.

Pre-procedure1
(a) Immerse the water inlet with thermostat sub-assembly in water and then gradually heat the water.
Procedure1
(b) Check that the valve of the water inlet with thermostat sub-assembly opens at the specified temperature.
Standard Valve Opening Temperature:
Specified Condition | Result |
|---|---|
80 to 84 °C 176 to 183 °F |
°C °F |
If the result is not as specified, replace the water inlet with thermostat sub-assembly.
Procedure2
(c) Check the valve lift. Standard Valve Lift:
If the result is not as specified, replace the water inlet with thermostat sub-assembly. |
|
Procedure3
(d) Check that the valve is fully closed when the water inlet with thermostat sub-assembly is at low temperatures (below 77 °C).
If it is not fully closed, replace the water inlet with thermostat sub-assembly.
Post-procedure1
(e) None
Installation
INSTALLATION
COMPONENTS (INSTALLATION)
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
WATER INLET WITH THERMOSTAT SUB-ASSEMBLY |
16031 |
- |
- |
- |
2 |
ENGINE OIL LEVEL DIPSTICK GUIDE |
11452 |
- |
- |
- |
3 |
ENGINE OIL LEVEL DIPSTICK |
15301 |
- |
- |
- |
*A |
Type A |
*B |
Type B |
*1 |
NO. 2 RADIATOR HOSE |
*2 |
NO. 3 WATER BY-PASS HOSE |
*3 |
GASKET |
*4 |
ENGINE OIL LEVEL DIPSTICK GUIDE O-RING |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
4 |
INLET NO. 1 AIR CLEANER |
17751 |
- |
- |
- |
5 |
AIR CLEANER BRACKET |
17771A |
- |
- |
- |
6 |
AIR CLEANER CASE SUB-ASSEMBLY |
17701 |
- |
- |
- |
7 |
AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
17801 |
- |
- |
- |
8 |
AIR CLEANER CAP SUB-ASSEMBLY |
17705 |
- |
- |
|
9 |
INLET NO. 2 AIR CLEANER |
17752 |
- |
- |
|
10 |
RADIATOR SUPPORT OPENING COVER |
53289A |
- |
- |
- |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
- |
- |

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
11 |
ADD ENGINE COOLANT (for Engine) |
- |
- |
- |
|
12 |
INSPECT FOR COOLANT LEAK (for Engine) |
- |
- |
- |
|
13 |
NO. 1 ENGINE UNDER COVER ASSEMBLY |
51410 |
- |
- |
- |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
- |
- |
PROCEDURE
1. INSTALL WATER INLET WITH THERMOSTAT SUB-ASSEMBLY
Torque:
10 N·m {102 kgf·cm, 7 ft·lbf}
2. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE
Torque:
21 N·m {214 kgf·cm, 15 ft·lbf}
3. INSTALL ENGINE OIL LEVEL DIPSTICK
4. INSTALL INLET NO. 1 AIR CLEANER
Click here ![]()
5. INSTALL AIR CLEANER BRACKET
Click here ![]()
6. INSTALL AIR CLEANER CASE SUB-ASSEMBLY
Click here ![]()
7. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
8. INSTALL AIR CLEANER CAP SUB-ASSEMBLY
![]() |
Click here |
9. INSTALL INLET NO. 2 AIR CLEANER
![]() |
Click here |
10. INSTALL RADIATOR SUPPORT OPENING COVER
11. ADD ENGINE COOLANT (for Engine)
Click here ![]()
12. INSPECT FOR COOLANT LEAK (for Engine)
Click here ![]()
13. INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY
Click here ![]()





























