Windshield Glass

In this manual: Windshield Glass
How To Troubleshoot Ecu Controlled Systems — 1How To Use This Manual — 1Identification Information — 1Repair Instruction — 1Terms — 12zr-fxe Air Cleaner Filter Element — 12zr-fxe Auxiliary Battery — 12zr-fxe Coolant (for Engine Coolant) — 12zr-fxe Oil And Oil Filter — 12zr-fxe Spark Plug — 1Air Conditioning Filter — 1Battery Cooling Filter — 1Brake Fluid — 1Coolant (for Inverter) — 1Front Brake Flexible Hose — 1Front Disc Brake Pad — 1Front Lower Ball Joint — 1Front Wheel Alignment — 1Front Wiper Rubber — 1General Maintenance — 1M20a-fxs Air Cleaner Filter Element — 1M20a-fxs Auxiliary Battery — 1M20a-fxs Coolant (for Engine Coolant) — 1M20a-fxs Oil And Oil Filter — 1M20a-fxs Spark Plug — 1Pa10/pb10/pb12 Hybrid Transaxle Fluid — 1Q810 Hybrid Transaxle Fluid — 1Rear Brake Flexible Hose — 1Rear Disc Brake Pad — 1Rear Wheel Alignment — 1Steering Column — 1Tire And Wheel — 1Transmitter Battery — 1When Disconnecting Or Reconnecting Battery Terminal — 1When Replacing Or Removing/installing Parts — 1Automatic High Beam Main Switch — 1Automatic High Beam System — 1Driver Monitor Camera — 1Driver Monitor Camera System — 1Driver Monitor Ecu — 1Front Camera — 1Front Camera System — 1Front Radar Sensor System — 1Front Side Radar Sensor — 1Front Side Radar Sensor System — 1Millimeter Wave Radar Sensor — 1Utility — 1Advanced Park — 1Advanced Park Main Switch — 1Amplifier Antenna — 1Audio And Visual System — 1Front Door Speaker — 1Instrument Panel Speaker — 1Microphone — 1Noise Filter — 1Pillar Speaker — 1Radio Antenna Cord (for Back Door) — 1Radio Antenna Cord (for Instrument Panel) — 1Radio Antenna Cord (for Roof) — 1Radio Receiver — 1Rear Door Speaker — 1Roof Antenna — 1Stereo Component Amplifier — 1Stereo Jack Adapter Assembly — 1Window Glass Antenna Wire — 1Back-up Battery — 1Dcm(telematics Transceiver) — 1Manual(sos)switch — 1Safety Connect System — 1Telephone And Gps Antenna (for Front Side) — 1Telephone And Gps Antenna (for Roof Side) — 1Telephone And Gps Antenna Cords — 1Garage Door Opener System (for Digital Inner Mirror) — 1Garage Door Opener System (for Ec Inner Mirror) — 1Blind Spot Monitor Sensor — 1Blind Spot Monitor System — 1Clearance Warning Ecu — 1Intuitive Parking Assist System — 1Panoramic View Monitor Switch — 1Panoramic View Monitor System — 1Parking Assist Ecu — 1Parking Assist Light — 1Parking Assist Monitor System — 1Parking Support Brake System — 1Rear View Monitor System — 1Television Camera (for Front) — 1Television Camera (for Rear) — 1Television Camera (for Side) — 1Ultrasonic Sensor (for Front) — 1Ultrasonic Sensor (for Rear) — 1Brake Actuator — 1Brake Pedal Stroke Sensor — 1Electronically Controlled Brake System — 1Front Speed Sensor — 1Rear Speed Sensor (for Awd) — 1Steering Angle Sensor — 1Brake Booster — 1Brake Fluid — 1Brake Line — 1Brake Pedal — 1Brake System — 1Electric Parking Brake Actuator — 1Electric Parking Brake Switch — 1Electric Parking Brake System — 1Forced Release — 1Front Axle Hub — 1Front Axle Hub Bolt — 1Rear Axle Carrier (for 2wd) — 1Rear Axle Carrier (for Awd) — 1Rear Axle Hub (for 2wd) — 1Rear Axle Hub (for Awd) — 1Rear Axle Hub Bolt — 1Steering Knuckle — 1Drive Shaft System — 1Front Drive Shaft Assembly — 1Rear Drive Shaft Assembly — 1Combination Switch — 1Electronic Shift Lever System — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Oil Seal — 1Hybrid Transaxle System — 1Input Shaft Oil Seal — 1Motor Cable — 1Pa10 Hybrid Vehicle Transaxle — 1Pa10 Manual Parking Lock Release — 1Pa10 Oil Cooler — 1Pb10/pb12 Hybrid Vehicle Transaxle — 1Pb10/pb12 Manual Parking Lock Release — 1Pb10/pb12 Oil Cooler — 1Shift Control Actuator — 1Shift Lever — 1Shift Lever Knob — 1Differential Side Gear Shaft — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Side Gear Oil Seal — 1Motor Cable — 1Rear Traction Motor — 1Coolant (for Engine) — 1Cooling Fan Motor — 1Cooling Fan System — 1Radiator — 1Relay — 1Thermostat — 1Water Pump — 1Canister — 1Egr Cooler — 1Egr Valve — 1Emission Control System — 1Fuel Tank Cap — 1Pcv Valve — 1Purge Valve — 1Vacuum Sensor — 1Air Fuel Ratio Sensor — 1Camshaft Oil Control Valve — 1Camshaft Position Sensor — 1Crankshaft Position Sensor — 1Ecm — 1Engine Coolant Temperature Sensor — 1Heated Oxygen Sensor — 1Ignition Coil And Spark Plug — 1Ignition System — 1Knock Sensor — 1Mass Air Flow Meter — 1Relay — 1Sfi System — 1Throttle Body — 1Camshaft — 1Cylinder Block — 1Cylinder Head — 1Cylinder Head Gasket — 1Engine — 1Engine Assembly — 1Engine Unit — 1Front Crankshaft Oil Seal — 1Rear Crankshaft Oil Seal — 1Fuel Filter — 1Fuel Injector — 1Fuel Pressure Regulator — 1Fuel Pump — 1Fuel Sender Gauge Assembly — 1Fuel System — 1Fuel Tank — 1Air Cleaner Filter Element — 1Exhaust Manifold — 1Exhaust Pipe — 1Intake Manifold — 1Intake System — 1Lubrication System — 1Oil And Oil Filter — 1Oil Pan And Oil Level Sensor — 1Oil Pressure Switch — 1Oil Pump — 1Accelerator Pedal Sensor — 1Battery Blower (for Hev Model) — 1Battery Ecu (for Hev Model) — 1Battery Ecu (for Phev Model) — 1Battery Voltage Sensor (for Phev Model) — 1Charge Cable (for Phev Model) — 1Charge Indicator (for Phev Model) — 1Charge Inlet (for Phev Model) — 1Combination Switch — 1Coolant (for Inverter) — 1Cooler (for Phev Model) — 1Electric Vehicle Charger Assembly (for Phev Model) — 1Frame Wire (for Hev Model) — 1Frame Wire (for Phev Model) — 1Heater Relay (for Phev Model) — 1Hv Battery (for Hev Model) — 1Hv Battery (for Phev Model) — 1Hv Battery Heater (for Phev Model) — 1Hv Battery Stack (for Phev Model) — 1Hv Relay Assembly (for Hev Model) — 1Hv Relay Assembly (for Phev Model) — 1Hybrid Battery System (for 2zr-fxe) — 1Hybrid Battery System (for M20a-fxs) — 1Hybrid Battery System (for Phev Model) — 1Hybrid Vehicle Control Ecu — 1Inverter With Converter (for Hev Model) — 1Motor Generator Control System (for 2zr-fxe) — 1Plug-in Charge Control System (for Phev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Service Plug Grip (for Hev Model) — 1Sub Radiator — 1Water Pump With Motor — 1Auxiliary Battery — 1Battery Current Sensor — 1Charging System — 1Solar Charging System — 1Solar Control Unit — 1Solar Roof — 1Can Communication System (for Hev Model) — 1Lin Communication System — 1Network Gateway Ecu — 1Integration Control Supply — 1Main Body Ecu — 1Power Integration System — 1Sub Battery System — 1Power Steering Ecu — 1Power Steering System — 1Heated Steering Wheel Controller — 1Heated Steering Wheel System — 1Steering Column Assembly — 1Steering Heater Switch — 1Steering Pad Switch — 1Steering System — 1Steering Wheel — 1Front Lower Ball Joint — 1Front Lower Suspension Arm (for 2zr-fxe Lh Side) — 1Front Lower Suspension Arm (for 2zr-fxe Rh Side) — 1Front Lower Suspension Arm (for M20a-fxs) — 1Front Shock Absorber — 1Front Stabilizer Bar — 1Front Suspension Member — 1Rear Coil Spring — 1Rear Lower Arm (for Awd Lh Side) — 1Rear Lower Arm (for Awd Rh Side) — 1Rear Lower Arm (for Hev Model 2wd) — 1Rear Lower Arm (for Phev Model) — 1Rear Shock Absorber — 1Rear Stabilizer Bar — 1Rear Suspension Member (for 2wd) — 1Rear Suspension Member (for Awd) — 1Rear Trailing Arm — 1Rear Upper Arm — 1Tire And Wheel System — 1Tire Repair Seal — 1Tire Pressure Warning Receiver — 1Tire Pressure Warning System — 1Tire Pressure Warning Valve — 1Acoustic Vehicle Alerting System — 1Vehicle Approaching Speaker — 1Vehicle Approaching Speaker Ecu — 1Back Door — 1Back Door Closer Ecu — 1Back Door Opener Switch — 1Back Door Support — 1Back Door Weatherstrip — 1Charge Lid Courtesy Switch — 1Charge Lid Opener Motor Assembly — 1Charge Lid Opener System — 1Charge Lid Opener Unit — 1Front Door — 1Front Door Opening Trim Weatherstrip — 1Fuel Lid Opener Motor Assembly — 1Fuel Lid Opener Switch — 1Fuel Lid Opener System — 1Hood — 1Hood Lock Control Cable Assembly — 1Power Back Door Closer Switch — 1Power Back Door Control Switch — 1Power Back Door Drive Unit — 1Power Back Door System — 1Power Back Door Touch Sensor — 1Power Back Door Warning Buzzer — 1Rear Door — 1Rear Door Opening Trim Weatherstrip — 1Reserve Lock Switch — 1Front Bumper — 1Front Door Belt Moulding — 1Front Door Window Frame Moulding — 1Front Fender — 1Front Pillar Upper Cover — 1Grille Shutter — 1Grille Shutter System — 1Name Plate — 1Quarter Garnish — 1Rear Bumper — 1Rear Door Belt Moulding — 1Rear Door Window Frame Moulding — 1Rear Wheel House Plate — 1Rocker Panel Moulding — 1Roof Drip Side Finish Moulding — 1Roof Garnish — 1Wheel Opening Moulding (for Front Side) — 1Wheel Opening Moulding (for Rear Side) — 1Windshield Outside Moulding — 1Horn — 1Horn System — 1Relay — 1Automatic Light Control Sensor — 1Back-up Light Assembly — 1Charge Lid Light — 1Front Marker Light — 1Hazard Warning Switch — 1Headlight Assembly — 1Headlight Dimmer Switch — 1Headlight Leveling Switch — 1High Mounted Stop Light Assembly — 1Illumination Light Assembly — 1License Plate Light Assembly — 1Lighting System — 1Rear Combination Light Assembly — 1Rear Light Assembly — 1Rear Side Marker Light Assembly — 1Relay — 1Side Turn Signal Light Assembly — 1Stop Light Switch — 1Switch Housing — 1Outer Mirror Switch — 1Outer Rear View Mirror — 1Outer Rear View Mirror Cover — 1Outer Rear View Mirror Glass — 1Power Mirror Control System — 1Back Door Glass — 1Front Passenger Side Power Window Switch — 1Power Window Control System — 1Power Window Master Switch — 1Power Window Regulator Motor (for Front Door) — 1Power Window Regulator Motor (for Rear Door) — 1Rear Power Window Switch — 1Relay — 1Roof Window Fix Glass — 1Window Defogger System — 1Windshield Deicer Switch — 1Windshield Deicer System — 1Windshield Glass — 1Front Wiper Motor — 1Rain Sensor — 1Relay — 1Washer Motor — 1Washer Nozzle (for Front Side) — 1Washer Nozzle (for Rear Television Camera) — 1Wiper And Washer System — 1Wiper Ecu — 1Wiper Switch — 1Back Door Lock — 1Door Control Receiver — 1Door Control Switch — 1Door Control Transmitter — 1Door Lock Release Motor (for Rear Side) — 1Door Outside Handle (for Rear Side) — 1Front Door Lock — 1Power Door Lock Control System — 1Rear Door Lock — 1Transmitter Battery — 1Wireless Door Lock Control System — 1Accumulator — 1Air Conditioning Amplifier — 1Air Conditioning Panel — 1Air Conditioning Pressure Sensor — 1Air Conditioning Unit — 1Ambient Temperature Sensor — 1Blower Unit — 1Condenser (for Hev Model) — 1Condenser (for Phev Model) — 1Discharge Temperature Sensor — 1Electric Expansion Valve (cooling) — 1Electric Expansion Valve (heating) — 1Evaporator Pipe Temperature Sensor — 1Evaporator Pressure Regulator — 1Front Blower Motor — 1Front Evaporator Front Solenoid Valve — 1Air Conditioning System (for Hev Model) — 1Front Evaporator Temperature Sensor — 1Heat Exchanger Temperature Sensor — 1Heat Pump Ecu — 1High Pressure Magnetic Valve — 1Humidity Sensor — 1Internal Condenser Temperature Sensor — 1Low Pressure Magnetic Valve — 1Refrigerant (for Hfc-134a(r134a)) — 1Refrigerant Line (for Hev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Room Temperature Sensor — 1Solar Sensor — 1Floor Carpet — 1Front Console Box — 1Instrument Panel Safety Pad — 1Roof Headlining — 1Roof Sunshade — 1Ambient Light (for Driver Side) — 1Ambient Light (for Front Passenger Side) — 1Back Door Courtesy Switch — 1Footwell Light — 1Glove Box Light — 1Lighting System — 1Luggage Compartment Room Light — 1Personal Light — 1Room Light — 1Vanity Light — 1Vanity Light Switch — 1Combination Meter — 1Meter / Gauge System — 1Trip Switch — 1Digital Inner Mirror — 1Digital Rear-view Mirror System — 1Inner Mirror Monitor Camera — 1Inner Rear View Mirror (w/o Ec Mirror) — 1Accessory Power Outlet System — 1Power Outlet Socket (for Console Box Front Side) — 1Power Outlet Socket (for Console Box Rear Side) — 1Power Outlet Socket (for Console Box) — 1Power Outlet Socket (for Luggage Compartment) — 1Power Outlet Switch — 1Wireless Charger Assembly — 1Wireless Charging System — 1Climate Control Seat System — 1Front Power Seat Control System (w/ Memory) — 1Front Power Seat Motor Assembly — 1Front Seat Assembly (for Power Seat) — 1Front Seat Cushion Heater (for Power Seat) — 1Front Seatback Heater (for Power Seat) — 1Lumbar Support Adjuster Assembly — 1Power Seat Control Ecu — 1Power Seat Switch — 1Power Seat Track Rail Assembly — 1Rear Seat Assembly — 1Rear Seat Cushion Heater — 1Rear Seat Reminder System — 1Rear Seatback Heater — 1Seat Heater Control — 1Seat Heater Switch (for Front Seat) — 1Seat Heater Switch (for Rear Side) — 1Seat Heater System — 1Seat Memory Switch — 1Child Restraint Seat Anchor Bracket — 1Front Seat Inner Belt Assembly — 1Front Seat Outer Belt Assembly — 1Occupant Detection Sensor (for Front Passenger Side) — 1Rear Center Seat Outer Belt Assembly — 1Rear Seat Inner Belt Assembly (for Rh Side) — 1Rear Seat Outer Belt Assembly — 1Seat Belt Warning System (w/ Occupant Classification System) — 1Tongue Plate Stopper — 1Airbag System — 1Center Airbag Sensor Assembly — 1Curtain Shield Airbag Assembly — 1Front Airbag Sensor — 1Front Passenger Airbag Assembly — 1Front Seat Side Airbag Assembly — 1Inspection After Collision — 1Knee Airbag Assembly — 1Occupant Classification System — 1Rear Seat Side Airbag Assembly — 1Side Airbag Sensor (for Center Pillar) — 1Side Airbag Sensor (for Front Door) — 1Spiral Cable — 1Steering Pad — 1Certification Ecu — 1Digital Key Ecu — 1Digital Key Receiver (for Front Floor) — 1Digital Key Receiver (for Outside Luggage Compartment) — 1Digital Key Receiver (for Rear Door) — 1Digital Key System — 1Electrical Key Oscillator (for Front Floor) — 1Electrical Key Oscillator (for Outside Luggage Compartment) — 1Electrical Key Oscillator (for Rear Floor) — 1Engine Hood Courtesy Switch — 1Id Code Box — 1Smart Key System (for Start Function) — 1
18steps
~108min
5/5difficulty
Done 0 of 18
  • Removal
  • Installation

Removal

REMOVAL

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during windshield glass removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedures

Effect/Inoperative Function When Necessary Procedures are not Performed

Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

Windshield glass*

Adjust forward recognition camera

  • Front Camera System
  • Automatic High Beam System

One Time Recognition:

Driving Adjustment:

NOTICE:

  • After cutting off the old adhesive remaining on the adhesion surface, apply new adhesive within 2 hours.
  • If the cut surface of the old adhesive is left exposed for a long time, the adhesion strength will be reduced, so apply the new adhesive quickly.
COMPONENTS (REMOVAL)

Procedure

Part Name Code

1

FRONT WIPER ARM HEAD CAP

85292B

-

-

2

SHIELD CAP

85247

-

-

3

FRONT WIPER ARM AND BLADE ASSEMBLY LH

-

-

-

-

4

FRONT WIPER ARM AND BLADE ASSEMBLY RH

-

-

-

-

5

WINDSHIELD LOWER OUTSIDE MOULDING LH

75536D

-

-

6

WINDSHIELD LOWER OUTSIDE MOULDING RH

75535F

-

-

7

COWL WATER EXTRACT SHIELD LH

55754F

-

-

-

8

COWL WATER EXTRACT SHIELD RH

55753D

-

-

-

9

COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

55708

-

-

-

10

FORWARD RECOGNITION CAMERA

8646C

-

-

-

11

RAIN SENSOR

89941

-

-

-

12

INNER REAR VIEW MIRROR ASSEMBLY

87810

-

-

-

13

FRONT DOOR OPENING TRIM WEATHERSTRIP LH

62312B

-

-

-

14

FRONT DOOR OPENING TRIM WEATHERSTRIP RH

62311B

-

-

-

15

FRONT PILLAR GARNISH LH

62212

-

-

16

FRONT PILLAR GARNISH RH

62211

-

-

17

MAP LIGHT ASSEMBLY

-

-

-

-

*A

w/ Rain Sensor

*B

for M20A-FXS

*C

for 2ZR-FXE

-

-

●

Non-reusable part

-

-

Procedure

Part Name Code

18

VISOR ASSEMBLY LH

74320

-

-

-

19

VISOR ASSEMBLY RH

74310

-

-

-

20

ASSIST GRIP COVER

74612

-

-

21

ASSIST GRIP

-

-

-

-

22

VANITY LIGHT ASSEMBLY

81340

-

-

23

ROOF HEADLINING ASSEMBLY

-

-

-

*1

VISOR HOLDER

-

-

Procedure

Part Name Code

24

WINDSHIELD GLASS SUB-ASSEMBLY

-

-

-

25

WINDSHIELD OUTSIDE MOULDING

75533G

-

-

26

NO. 2 WINDOW GLASS ADHESIVE DAM

56118B

-

-

27

FRONT WINDOW INNER CENTER MOULDING

56153C

-

-

28

NO. 1 WINDSHIELD GLASS STOPPER

56115A

-

-

29

NO. 2 WINDSHIELD GLASS STOPPER

56116C

-

-

30

NO. 1 WINDSHIELD GLASS STOPPER

56115A

-

-

*A

for 2-piece Type

*B

for 1-piece Type

●

Non-reusable part

-

-

PROCEDURE

1. REMOVE FRONT WIPER ARM HEAD CAP

Click here

2. REMOVE SHIELD CAP

Click here

3. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

Click here

4. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

Click here

5. REMOVE WINDSHIELD LOWER OUTSIDE MOULDING LH

Click here

6. REMOVE WINDSHIELD LOWER OUTSIDE MOULDING RH

(a) Use the same procedure as for the LH side.

7. REMOVE COWL WATER EXTRACT SHIELD LH

Click here

8. REMOVE COWL WATER EXTRACT SHIELD RH

(a) Use the same procedure as for the LH side.

9. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Click here

10. REMOVE FORWARD RECOGNITION CAMERA

Click here

11. REMOVE RAIN SENSOR (w/ Rain Sensor)

Click here

12. REMOVE INNER REAR VIEW MIRROR ASSEMBLY

w/o EC Mirror: Click here

w/ EC Mirror: Click here

for Digital Inner Mirror: Click here

13. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

14. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

(a) Use the same procedure as for the LH side.

15. REMOVE FRONT PILLAR GARNISH LH

Click here

16. REMOVE FRONT PILLAR GARNISH RH

(a) Use the same procedure as for the LH side.

17. REMOVE MAP LIGHT ASSEMBLY

Click here

18. REMOVE VISOR ASSEMBLY LH

Click here

19. REMOVE VISOR ASSEMBLY RH

(a) Use the same procedure as for the LH side.

20. REMOVE ASSIST GRIP COVER

Click here

21. REMOVE ASSIST GRIP

Click here

22. REMOVE VANITY LIGHT ASSEMBLY

Click here

23. DISCONNECT ROOF HEADLINING ASSEMBLY

Rotation Direction

Remove in this Direction (1)

Remove in this Direction (2)

-

-

(1) Turn each visor holders approximately 45° and remove them as indicated by the arrows, in the order shown in the illustration.

(2) Disengage the 4 claws as shown in the illustration to remove the base of each visor holder.

(1) Slightly lower the front section of the roof headlining assembly so that the windshield glass can be removed.

NOTICE:

Do not damage the roof headlining assembly or Toyota Prius vehicle interior.

HINT:

It is not necessary to completely remove the roof headlining assembly.

24. REMOVE WINDSHIELD GLASS SUB-ASSEMBLY

NOTICE:

  • After cutting off the old adhesive remaining on the adhesion surface, apply new adhesive within 2 hours.
  • If the cut surface of the old adhesive is left exposed for a long time, the adhesion strength will be reduced, so apply the new adhesive quickly.

(a) w/ Windshield Deicer System:

(1) Disconnect the connector.

Protective Tape

-

-

(1) Apply protective tape to the area around the installation position of the windshield glass on the Toyota Prius vehicle body to prevent it from being scratched.

*a

Cut

-

-

(1) Using a knife, cut off the windshield outside moulding as shown in the illustration.

*a

Matchmark

-

-

(1) Place matchmarks on the windshield glass and Toyota Prius vehicle body at the locations indicated in the illustration.

HINT:

Matchmarks are not necessary if the windshield glass is not going to be reused.

*a

Suction Cup

-

-

(1) Install the 2 suction cups to the windshield glass.

*1

Windshield Glass

-

-

*a

Windshield Knife

*b

Adhesive

Pull

-

-

(1) When using a windshield knife:

  1. Apply soapy water to the area around the adhesive.
  2. Insert a windshield knife into the adhesive between the windshield glass and Toyota Prius vehicle body.
  3. While keeping the windshield knife perpendicular to the outer surface of the windshield glass, cut the adhesive by pulling the windshield knife around the windshield glass.

    NOTICE:

    • Do not pry the windshield glass with the windshield knife.
    • Do not use a windshield knife to cut the adhesive on the lower side of the windshield glass.
    • When separating the windshield glass, be careful not to damage the paint or interior and exterior ornaments.

    HINT:

    Insert the windshield knife in an area where the gap between windshield glass and Toyota Prius vehicle body is large.

*1

Windshield Glass Stopper

-

-

*a

Piano Wire

-

-

(1) When using piano wire:

  1. Pass a piano wire between the Toyota Prius vehicle body and glass from the interior, as shown in the illustration.
  2. Tie both wire ends to wooden blocks or similar objects that can serve as handles.
  3. Cut the adhesive by pulling the piano wire around the windshield glass.

    NOTICE:

    • When separating the windshield glass, be careful not to damage the paint or interior and exterior ornaments.
    • To prevent the safety pad from being scratched when removing the windshield glass, place a plastic sheet between the piano wire and safety pad.

*A

for 1-piece Type

*B

for 2-piece Type

*1

No. 1 Windshield Glass Stopper

*2

No. 2 Windshield Glass Stopper

(1) Disengage the windshield glass stoppers.

NOTICE:

  • The No. 1 windshield glass stoppers and No. 2 windshield glass stoppers are installed to the windshield glass as shown in the illustration. Be careful not to damage the windshield glass when cutting the adhesive.
  • To prevent the windshield glass from falling when performing this operation, be sure to hold the windshield glass using 2 suction cups.

HINT:

Depending on the Toyota Prius vehicle, either 1-piece type or 2-piece type stoppers may be present.

25. REMOVE WINDSHIELD OUTSIDE MOULDING

(a) When reusing the windshield glass:

*a

Back Side

-

-

(1) Using a scraper, remove the windshield outside moulding.

NOTICE:

  • Be careful not to damage the windshield glass.
  • Be sure to replace the windshield outside moulding with a new one.

26. REMOVE NO. 2 WINDOW GLASS ADHESIVE DAM

(a) When reusing the windshield glass:

*a

Back Side

-

-

(1) Using a scraper, remove the 3 No. 2 windshield glass adhesive dams.

NOTICE:

  • Be careful not to damage the windshield glass.
  • Be sure to replace the windshield glass adhesive dam with a new one.

27. REMOVE FRONT WINDOW INNER CENTER MOULDING

*a

Back Side

*b

Matchmark

(1) Place matchmarks on the windshield glass at the locations indicated in the illustration.

(2) Using a scraper, remove the front window inner center moulding.

NOTICE:

  • Be careful not to damage the windshield glass.
  • Be sure to replace the front window inner center moulding with a new one.

28. REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 1-piece Type)

(a) When reusing windshield glass:

*a

Back Side

-

-

(1) Remove the 2 No. 1 windshield glass stoppers as shown in the illustration.

NOTICE:

  • Be careful not to damage the windshield glass.
  • Be sure to replace the 1-piece type No. 1 windshield glass stoppers with new 2-piece type No. 1 and No. 2 windshield glass stoppers.

29. REMOVE NO. 2 WINDSHIELD GLASS STOPPER (for 2-piece Type)

(a) When reusing the windshield glass:

*a

Back Side

-

-

(1) Using a scraper, remove the 2 No. 2 windshield glass stoppers.

NOTICE:

  • Be careful not to damage the windshield glass.
  • Be sure to replace the No. 2 windshield glass stoppers with new ones.

30. REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type)

*1

No. 1 Windshield Glass Stopper

-

-

(1) Remove the 2 No. 1 windshield glass stoppers from the Toyota Prius vehicle body.

NOTICE:

Be sure to replace the No. 1 windshield glass stoppers with new ones.

Installation

INSTALLATION

NOTICE:

  • Make sure to use Toyota Genuine Windshield Glass Adhesive (High Modulus Type) or an equivalent high modulus adhesive.
  • After cutting off the old adhesive remaining on the adhesion surface, apply new adhesive within 2 hours.
  • If the cut surface of the old adhesive is left exposed for a long time, the adhesion strength will be reduced, so apply the new adhesive quickly.
  • When replacing the windshield glass of a Toyota Prius vehicle equipped with a forward recognition camera, make sure to use a Lexus genuine part. If a non-Lexus genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket. Also, the dynamic radar cruise control system, front camera system, lane tracing assist system, pre-collision system or adaptive high beam system may not operate properly due to a difference in the transmissivity or black ceramic border.
COMPONENTS (INSTALLATION)

Procedure

Part Name Code

1

NO. 1 WINDSHIELD GLASS STOPPER

56115A

-

-

2

NO. 2 WINDSHIELD GLASS STOPPER

56116C

-

-

3

FRONT WINDOW INNER CENTER MOULDING

56153C

-

-

4

NO. 2 WINDOW GLASS ADHESIVE DAM

56118B

-

-

5

WINDSHIELD OUTSIDE MOULDING

75533G

-

-

6

WINDSHIELD GLASS SUB-ASSEMBLY

-

-

-

7

INSPECT FOR LEAK AND REPAIR

-

-

-

●

Non-reusable part

-

-

Procedure

Part Name Code

8

ROOF HEADLINING ASSEMBLY

-

-

-

9

VANITY LIGHT ASSEMBLY

81340

-

-

-

10

ASSIST GRIP SUB-ASSEMBLY

74610E

-

-

11

VISOR ASSEMBLY RH

74310

-

-

-

12

VISOR ASSEMBLY LH

74320

-

-

-

*1

VISOR HOLDER

-

-

Procedure

Part Name Code

13

MAP LIGHT ASSEMBLY

-

-

-

-

14

FRONT PILLAR GARNISH LH

62212

-

-

15

FRONT PILLAR GARNISH RH

62211

-

-

16

FRONT DOOR OPENING TRIM WEATHERSTRIP RH

62311B

-

-

-

17

FRONT DOOR OPENING TRIM WEATHERSTRIP LH

62312B

-

-

-

18

INNER REAR VIEW MIRROR ASSEMBLY

87810

-

-

-

19

RAIN SENSOR

89941

-

-

-

20

FORWARD RECOGNITION CAMERA

8646C

-

-

-

21

COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

55708

-

-

-

22

COWL WATER EXTRACT SHIELD RH

55753D

-

-

-

23

COWL WATER EXTRACT SHIELD LH

55754F

-

-

-

24

WINDSHIELD LOWER OUTSIDE MOULDING LH

75536D

-

-

-

25

WINDSHIELD LOWER OUTSIDE MOULDING RH

75535F

-

-

-

26

FRONT WIPER ARM AND BLADE ASSEMBLY LH

-

-

-

27

FRONT WIPER ARM AND BLADE ASSEMBLY RH

-

-

-

28

INSPECT FRONT WIPER ARM AND BLADE ASSEMBLY

-

-

-

29

SHIELD CAP

85247

-

-

-

30

FRONT WIPER ARM HEAD CAP

85292B

-

-

-

31

ADJUST FORWARD RECOGNITION CAMERA

8646C

-

-

*A

w/ Rain Sensor

*B

for M20A-FXS

*C

for 2ZR-FXE

-

-

N*m (kgf*cm, ft.*lbf): Specified torque

●

Non-reusable part

PROCEDURE

1. INSTALL NO. 1 WINDSHIELD GLASS STOPPER

*1

No. 1 Windshield Glass Stopper

-

-

(1) Install 2 new No. 1 windshield glass stoppers to the Toyota Prius vehicle body as shown in the illustration.

HINT:

Only 2-piece type windshield glass stoppers are provided as supply parts. Use 2-piece type stoppers as replacements even if 1-piece type stoppers were originally installed.

2. INSTALL NO. 2 WINDSHIELD GLASS STOPPER

*a

Back Side

*b

Ceramic Notch

*c

Windshield Glass Edge Side

-

-

Standard Dimension:

Area

Dimension

Area

Dimension

a

27.8 mm (1.094 in.)

-

-

(1) Using a brush or sponge, coat the installation area of 2 new No. 2 windshield glass stoppers with glass primer.

NOTICE:

  • Do not apply too much glass primer.
  • Allow the glass primer to dry for 3 minutes or more.
  • Throw away any leftover glass primer.

HINT:

If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.

(2) Install the 2 No. 2 windshield glass stoppers to the windshield glass as shown in the illustration.

HINT:

Only 2-piece type windshield glass stoppers are provided as supply parts. Use 2-piece type stoppers as replacements even if 1-piece type stoppers were originally installed.

3. INSTALL FRONT WINDOW INNER CENTER MOULDING

*a

Back Side

-

-

Glass Primer

-

-

Standard Dimension:

Item

Dimension

Item

Dimension

a

17.5 to 20.5 mm (0.689 to 0.807 in.)

-

-

(1) Using a brush or sponge, coat the adhesive application area with glass primer.

NOTICE:

  • Do not apply too much glass primer.
  • Allow the glass primer to dry for 3 minutes or more.
  • Throw away any leftover glass primer.

HINT:

If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.

*a

Back Side

-

-

(1) Install the new front window inner center moulding to the windshield glass as shown in the illustration.

Standard Dimension:

Item

Dimension

Item

Dimension

a

0.6 mm (0.0236 in.)

b

-2.0 to 2.0 mm (-0.0787 to 0.0787 in.)

NOTICE:

Do not damage the front window inner center moulding.

(2) Remove the matchmarks.

4. INSTALL NO. 2 WINDOW GLASS ADHESIVE DAM

*a

Back Side

*b

Ceramic Notch

Reference Measurement:

Area

Measurement

Area

Measurement

a

0.0 mm (0.0 in.)

b

82.1 to 83.1 cm (2.69 to 2.73 ft.)

c

83.2 to 84.2 cm (2.73 to 2.76 ft.)

d

128.8 to 129.8 cm (4.22 to 4.26 ft.)

(1) Using a brush or sponge, coat the installation area of 3 new windshield glass adhesive dams with glass primer.

NOTICE:

  • Do not apply too much glass primer.
  • Allow the glass primer to dry for 3 minutes or more.
  • Throw away any leftover glass primer.

HINT:

If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.

(2) Install the 3 windshield glass adhesive dams to the windshield glass as shown in the illustration.

5. INSTALL WINDSHIELD OUTSIDE MOULDING

*a

Back Side

-

-

Reference Measurement / Standard Dimension:

Area

Measurement

Area

Dimension

a

6.9 mm (0.272 in.)

b

-3.0 to 3.0 mm (-0.118 to 0.118 in.)

(1) Using a brush or sponge, coat the installation area of a new windshield outside moulding with glass primer.

NOTICE:

  • Do not apply too much glass primer.
  • Allow the glass primer to dry for 3 minutes or more.
  • Throw away any leftover glass primer.

HINT:

If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.

(2) Install the windshield outside moulding to the windshield glass as shown in the illustration.

6. INSTALL WINDSHIELD GLASS SUB-ASSEMBLY

NOTICE:

  • After cutting off the old adhesive remaining on the adhesion surface, apply new adhesive within 2 hours.
  • If the cut surface of the old adhesive is left exposed for a long time, the adhesion strength will be reduced, so apply the new adhesive quickly.

*a

Matchmark

*b

Suction Cup

(1) Prepare to install the windshield glass by the below procedure.

  1. Position the windshield glass.
  2. Using 2 suction cups, place the windshield glass in the correct position.
  3. Check that the whole contact surface of the windshield glass rim is perfectly even.
  4. Align the matchmarks on the windshield glass and Toyota Prius vehicle body.

    NOTICE:

    Check that the windshield glass stoppers are attached to the vehicle body correctly.

  5. Remove the windshield glass.
  6. Using a brush, coat the installation surface on the vehicle body with body primer.

    NOTICE:

    • Do not coat the adhesive with body primer.
    • Do not apply too much body primer.
    • Allow the body primer to dry for 3 minutes or more.
    • Throw away any leftover body primer.

*1

Windshield Outside Moulding

*2

Windshield Glass Adhesive Dam

*a

Back Side

-

-

Glass Primer

-

-

Standard Dimension:

Item

Dimension

Item

Dimension

a

10.5 mm (0.413 in.) or more

b

10.5 mm (0.413 in.) or more

c

10.5 mm (0.413 in.) or more

d

8.0 mm (0.3150 in.) or more

e

18 mm (0.709 in.) or more

-

-

(1) Using a brush or sponge, coat the adhesive application area with glass primer.

NOTICE:

  • Do not apply too much glass primer.
  • Allow the glass primer to dry for 3 minutes or more.
  • Throw away any leftover glass primer.

HINT:

  • Apply glass primer to the ceramic notches.
  • If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.

*a

Nozzle

-

-

(1) Prepare to apply adhesive to the windshield glass by the below procedure.

Adhesive:

Toyota Genuine Windshield Glass Adhesive (High modulus type) or equivalent

  1. Cut off the tip of the cartridge nozzle as shown in the illustration.

    Standard Dimension:

    Item

    Dimension

    Item

    Dimension

    a

    10.0 to 13.0 mm (0.394 to 0.512 in.)

    b

    6.0 to 9.0 mm (0.236 to 0.354 in.)

  2. Load the sealer gun with cartridge.

*1

Windshield Outside Moulding

*2

Windshield Glass Adhesive Dam

*a

Back Side

-

-

Adhesive

-

-

(1) Apply adhesive to the windshield glass, as shown in the illustration.

Standard Dimension:

Item

Dimension

Item

Dimension

a

11.5 mm (0.453 in.)

b

11.5 mm (0.453 in.)

c

11.4 mm (0.449 in.)

d

4.0 mm (0.157 in.)

e

6.0 mm (0.236 in.)

-

-

HINT:

Apply adhesive onto the ceramic notches.

*a

Matchmark

*b

Suction Cup

(1) Install the windshield glass.

  1. Using 2 suction cups, position the windshield glass so that the matchmarks are aligned, and press it in gently along the rim.

    NOTICE:

    • Check that the windshield glass stoppers are engaged to the Toyota Prius vehicle body correctly.
    • Check the clearance between the vehicle body and windshield glass.
  2. Lightly press the outer surface of the windshield glass to ensure that the windshield glass is securely fit to the vehicle body.

    HINT:

    Press the glass with a force of 98 N (10 kgf, 22.0 lbf) or more.

  3. Using a scraper, remove any excess or protruding adhesive.
  4. Hold the windshield glass using protective tape until the applied adhesive becomes hard.

    HINT:

    Follow the instructions supplied by the adhesive manufacturer or in the corresponding instruction manual for the minimum amount of time necessary to wait before driving the Toyota Prius vehicle.

(f) w/ Windshield Deicer System:

(1) Connect the connector.

7. INSPECT FOR LEAK AND REPAIR

(1) Inspect for leaks by the below procedure.

1. After the adhesive has hardened, apply water from the outside of the Toyota Prius vehicle. Check that no water leaks into the cabin.

2. If water leaks into the cabin, allow the water to dry and add adhesive.

3. Remove the protective tape.

8. INSTALL ROOF HEADLINING ASSEMBLY

(1) Return the front section of the roof headlining assembly to its original position.

NOTICE:

Do not damage the roof headlining assembly or Toyota Prius vehicle interior.

Install in this Direction

-

-

(1) Engage the 4 claws to install the base of each visor holder.

(2) Install the 2 visor holders as shown in the illustration.

9. INSTALL VANITY LIGHT ASSEMBLY

10. INSTALL ASSIST GRIP SUB-ASSEMBLY

Click here

11. INSTALL VISOR ASSEMBLY RH

12. INSTALL VISOR ASSEMBLY LH

13. INSTALL MAP LIGHT ASSEMBLY

14. INSTALL FRONT PILLAR GARNISH LH

Click here

15. INSTALL FRONT PILLAR GARNISH RH

(a) Use the same procedure as for the LH side.

16. CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

17. CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

18. INSTALL INNER REAR VIEW MIRROR ASSEMBLY

w/o EC Mirror: Click here

w/ EC Mirror: Click here

for Digital Inner Mirror: Click here

19. INSTALL RAIN SENSOR (w/ Rain Sensor)

Click here

20. INSTALL FORWARD RECOGNITION CAMERA

Click here

21. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Click here

22. INSTALL COWL WATER EXTRACT SHIELD RH

23. INSTALL COWL WATER EXTRACT SHIELD LH

24. INSTALL WINDSHIELD LOWER OUTSIDE MOULDING LH

25. INSTALL WINDSHIELD LOWER OUTSIDE MOULDING RH

26. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

Click here

27. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

Click here

28. INSPECT FRONT WIPER ARM AND BLADE ASSEMBLY

Click here

29. INSTALL SHIELD CAP

30. INSTALL FRONT WIPER ARM HEAD CAP

31. ADJUST FORWARD RECOGNITION CAMERA

(a) If the forward recognition camera has been replaced with a new one or the windshield glass has been removed and installed, it is necessary to perform Forward Recognition Camera Learning.

HINT:

Forward Recognition Camera Learning can be performed by using either One Time Recognition or Driving Adjustment.

Target Adjustment(One Time Recognition): Click here

Driving Adjustment: Click here